IBAYT-PBL3(motherboard card) AD1040(daughter...

1

IBAYT-PBL3(motherboard card)

AD1040(daughter card)

Intel® Bay Trail SOC

Atom™ J1900

Startup Manual V1.0

2

Copyright

The documentation and the software included with this product are copyrighted 2015 by

LONGSHINE Technology GmbH. All rights are reserved. LONGSHINE Technology GmbH reserves

the right to make improvements in the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in any form or by any

means without the prior written permission of LONGSHINE Technology GmbH. Information

provided in this manual is intended to be accurate and reliable. However, LONGSHINE Technology

GmbH assumes no responsibility for its use, nor for any infringements of the rights of third parties,

which may result from its use.

Safety Declaration

The manufacturer reserves the right to make changes, without notice, to any product, including

circuits and/or software described or contained in this manual in order to improve design and/or

performance. The manufacturer assumes no responsibility or liability for the use of the described

product(s), conveys no license or title under any patent, copyright, or masks work rights to these

products, and makes no representations or warranties that these products are free from patent,

copyright, or mask work right infringement, unless otherwise specified. For the detail product

information, please refer to user’s manual.

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use

liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment and must be

easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause

damage.

7. The openings on the enclosure are for air convection. Protect the equipment from overheating.

DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the equipment to the

power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over the power

cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by

qualified service personnel.

3

14. If one of the following situations arises, get the equipment checked by service personnel:

� The power cord or plug is damaged.

� Liquid has penetrated into the equipment.

� The equipment has been exposed to moisture.

� The equipment does not work well, or you cannot get it to work according to the user's

manual.

� The equipment has been dropped and damaged.

� The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD

DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED

ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE

MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S

INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70

dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. LONGSHINE Technology

GmbH disclaims all responsibility for the accuracy of any statements contained herein.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from damage.

To avoid electrical shock, always disconnect the power from your PC chassis before you work on it.

Don't touch any components on the CPU card or other cards while the PC is on.

Disconnect power before making any configuration changes. The sudden rush of power as you

connect

1. General Introduction

1.1 Product Overview

IBAYT-PBL3 is designed with Intel® Celeron™ J1900 SoC for industrial applications that request

performance computing and reliable stability. The motherboard has on board CPU Intel® Celeron™

J1900 Quad core 2.0 GHz.

IBAYT-PBL3 has rich I/O connectivity with PS/2, COM port, LAN, USB port and audio Jack

integrated in a customerized form factor. It also supports dual display for LVDS and VGA.

IBAYT-PBL3 also comes with plenty of connectivity and expansion options. 8-bit GPIO, mini PCIe

expansion slot and PCIe x 1 slot enable easy integration. 10/100/1000 Mbps Ethernet port is also

available to deliver high speed networking.

1.2 Specifications

Specifications

System

CPU BayTrail-D Intel® Celeron® Processor J1900

2GHz/2M Cache (Quad core)

BIOS AMI 64Mb SPI ROM

Memory - 2GB memory as Standard, Max. 8GB

- DDR3L-133 SO-DIMM Socket x 2 (Horizental type); 4GB on each SO-DIMM)

Watchdog Timer 256-level Watchdog Timer

H/W Status Monitor Monitoring System Temperature and Voltages

Expansion Slots 1 x Full-size mini-PCIe Socket (for Wireless LAN)

1 x mSATA Solid State Drive (SSD) slot (optional)

Wake up / Boot on LAN LAN (WOL,PXE)

Smart Fan Control Yes

Display

Chipset Intel® Integrated Graphics Engine (Dual Display Support)

Internal Display 2 x LVDS (Single Channel 24bits + Dual Channel 24bits) With Chrontel CH7511B IC

Internal Display 1 x DB-15 VGA ; Max resolution: 2048 x 1536

Touch IC 5-wired Flat Resistive Touch (EETI touch controller defined in daughter board)

Audio

Audio Codec Realtek® ALC892 HD Audio

Audio Amp 6W Audio Amp

Ethernet

LAN1 Intel® i211-AT PCIe Gigabit Ethernet Controller

External IO Ports

Serial Port External:

- 4 x RS-232 Ports (RJ45 type)

- COM1/2/3/4

- 0V/+5V/+12V power output by BIOS adustable; default 0V

USB Port 4 x USB 2.0

Cash Drawer Port - 1 x RJ-11

- +12/+24V power output by BIOS adjustable; default +24V

Keyboard/ Mouse 1 x PS2 (Keyboard/Mouse Auto Detection)

LAN Port 1 x RJ-45 GigLAN

VGA 1 x VGA (DB15)

4 pin DIN type 1x DIN (4P) 19V

Internal Connectors

Memory Slot 2 x SO-DIMM memory slot (Horizontal)

LVDS 1 x LVDS1 (30-pin Single Channel 24-bit)

1 x LVDS2 (40-pin, Dual Channel 24-bit)

LVDS Power 1 x LVDS PWR select (2x3 pin header for 3.3V/5V select)

SATA SATA1: 1 x SATA 22p

SATA2: 1 x mSATA

Clear CMOS Jumper 1 x CMOS Clear (1x3 pin header)

BIOS Flash 1 x SPI for BIOS flash (2x4 pin header)

Speaker out 1 x speaker out (1x2 pin header with R & L channel)

mini PCIe - 1 x mini PCIe

- with USB signal

Serial Port Internal :

- 2 x RS-232 PIN Header

- 0/12V/5V power output by BIOS adjustable; default 0V

For Touch controller:

- 1 x RS-232 PIN Header

- 0/12V/5V power output by BIOS adjustable; default +5V

USB Port 2 x USB 2.0 PIN Header(2x6 wafer)

1 x USB 2.0 PIN Header(1x4 wafer)

1 x USB 2.0 (in mini-PCIe)

Printer Port 1 x LPT (2x13 box header)

Battery 1 x Button Cell with wire (Horizontal paste on selected area)

Buzzer 1 x Buzzer

CPU/system fan

connector

Optional CPU/System fan (1x4 for CPU and 1x3 for SYS pin header)

6

1.3 Platform Features and Benefits

Integrated Gfx (Intel® HD Graphics) supports embedded hardware decode accelerator deliver

1080p HD video stream with excellent performance.

DirectX® 11.1 & Open GL 4.0 let you enjoy awesome graphics performance, stunning 3D visual

effect and dynamic interactivity

Memory support low voltage DDR3 memory controller

Operating system support:

– Windows 7 32 bit / 64 bit

– Windows 8 32 bit / 64 bit

– Fedora 18 Remix / Yocto

7

2. Product Introduction / Installation

2.1 Before you Proceed

Take note of the following precautions before you install motherboard components or change any

motherboard settings.

Caution!

� Unplug the power cord from the wall socket before touching any component.

� Use a grounded wrist strap or touch a safely grounded object or a metal object, such as

the power supply case, before handling components to avoid damaging them due to static

electricity

� Hold components by the edges to avoid touching the ICs on them.

� Whenever you uninstall any component, place it on a grounded anti-static pad or in the

bag that came with the component.

� Before you install or remove any component, ensure that the ATX power supply is

switched off or the power cord is detached from the power supply. Failure to do so may

cause severe damage to the motherboard, peripherals, and/or components.

2.2 Motherboard Overview

Before you install the motherboard, study the configuration of your chassis to ensure that the

motherboard fits into it. Refer to the chassis documentation before installing the motherboard.

Warning!

Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so

can cause you physical injury and damage motherboard components.

2.2.1 Placement Direction When installing the motherboard, make sure that you place it into the chassis in the correct

orientation. The edge with external ports goes to the rear part of the chassis as indicated in the

image below.

2.2.2 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis.

Caution!

Do not over tighten the screws! Doing so can damage the motherboard.

8

2.2.3 Motherboard Layout

IBAYT-PBL3 Top side:

IBAYT-PBL3 Bottom side:

9

2.2.4 Daughterboard Layout

AD1040 TOP side:

2.2.5 Jumper Content and Function List

Jumpers:

Label Function Note

JATX1

ATX/AT SELECTION

AT mode

ATX mode(default)

JVDD2

JLVDS2 Power select

1-3 (default): 3.3V

3-5: 5V

For LVDS2_VDD

2-4 (default): 3.3V

4-6: 5V

For JBKLVOL2

JVDD3

JLVDS2 Converter

Power select

5V

12V

JCMOS1

Clear CMOS

NA

Clear CMOS

10

2.2.6 MB Internal Connector and PIN Definition

Label Function Note

CPU_FAN

1.GND

2.12V

3.CPUFAN_DEC

4.CPUFAN_PWM

JFP1

PIN1 : +5VSB

PIN2 : PWR_LED#

PIN3 : PANSWIN#

PIN4 : GND

PIN5 : PMC_RST_BTN#_D

PIN6 : GND

JLVDS1

LVDS Connector

PIN1 : +12V_BL PIN21: LVDSA_N3

PIN2 : +12V_BL PIN22: LVDSA_N2

PIN3 : LVDS1_VDD L PIN23: GND

PIN4 : +12V_BL PIN24: GND

PIN5 : LVDS1_VDD PIN25: LVDSB_P1


PIN7 : LVDS1_EDID_CLK PIN27: LVDSB_N1

PIN8 : LVDS1_EDID_DATA PIN28: LVDSB_N0

PIN9 : BRIGHT1 PIN29: GND

PIN10 : LVDS_VDD_EN PIN30: GND

PIN11 : BL_EN PIN31: LVDSB_P3

PIN12 : LVDS1_DETECT#_C PIN32: LVDSB_P2

PIN13 : LVDSA_P1 PIN33: LVDSB_N3


PIN15 : LVDSA_N1 PIN35: GND


PIN17 : GND PIN37: LVDSB_CLK_P

PIN18 : GND PIN38: LVDSA_CLK_P

PIN19 : LVDSA_P3 PIN39: LVDSB_CLK_N

PIN20 : LVDSA_P2 PIN40: LVDSA_CLK_N

COM5,6

Serial Port Connector

PIN1 : COM1_DCD#

PIN2 : COM1_RXD

PIN3 : COM1_TXD

PIN4 : COM1_DTR#

PIN5 : GND

PIN6 : COM1_DSR#

PIN7 : COM1_RTS#

PIN8 : COM1_CTS#

PIN9 : C1_RID#

JSPI1

SPI debug port

PIN1 : +1.8V_SPI

PIN2 : GND

PIN3 : SPISKT_CS0#

PIN4 : SPISKT_CLK

PIN5 : SPISKT_MISO

PIN6 : SPISKT_MOSI

PIN7 : SPISKT_HOLD0#

11

JTOUCH1

PIN1: +5V

PIN2: +3.3V

PIN3: TOUCH_232_RXD

PIN4: TOUCH_232_TXD

PIN5: GND

JLVDS2

LVDS Connector

PIN1 : Conv_SRC PIN16 : LVDS2A_N2

PIN2 : LVDS2A_P3 PIN17 : LVDS2_VDD

PIN3 : Conv_SRC PIN18 : GND

PIN4 : LVDS2A_N3 PIN19 : LVDS2_VDD

PIN5 : BL_EN2 PIN20 : LVDS2A_P1

PIN6 : GND PIN21: +3.3V

PIN7 : BRIGHT2 PIN22: LVDS2A_N1

PIN8 : LVDS2A_CLK_P PIN23: GND

PIN9 : NC PIN24: GND

PIN10 : LVDS2A_CLK_N PIN25: LVDS2_EDID_DATA

PIN11 : LVDS2_DETECT#_C PIN26: LVDS2A_P0

PIN12 : GND PIN27: LVDS2_EDID_CLK

PIN13 : GND PIN28: LVDS2A_N0

PIN14 : LVDS2A_P2 PIN29: GND

PIN15 : GND PIN30: GND

JUSB1

PIN1: USB_HB_CM_P4 PIN7: USB_HB_CM_P2

PIN2: +5V_USB789 PIN8: USB_HB_CM_P3

PIN3: USB_HB_CM_N4 PIN9 : USB_HB_CM_N2

PIN4: +5V_USB789 PIN10: USB_HB_CM_N3

PIN5: GND PIN11: +5V_USB789


JUSB2,3

PIN1: +5V_USB56

PIN2: USB_CM_N2

PIN3: USB_CM_P2

PIN4: GND

JLPT1

PIN1 : LPT_STB# PIN14: GND

PIN2 : LPT_AFD# PIN15: LPT_PD6

PIN3 : LPT_PD0 PIN16: 16.GND

PIN4 : LPT_ERR# PIN17: LPT_PD7

PIN5 : LPT_PD1 PIN18: GND

PIN6 : LPT_INIT# PIN19: LPT_ACK#


PIN8 : LPT_SLIN# PIN21: LPT_BUSY


PIN10 : GND PIN23: LPT_PE

PIN11 : LPT_PD4 PIN24:GND

PIN12 : GND PIN25: LPT_SLCT

PIN13 : LPT_PD5 PIN26: NC

JAMP2

PIN1: AMP_L-

PIN2: AMP_L+

JCASE1

PIN1: SIO_CASEOPEN#

PIN2: GND

12

JRTC1

JTPM1

PIN1 : CK_25M_SIO_R

PIN2 : +3.3VSB

PIN3 : PLTRST_TPM#

PIN4 : +3.3V

PIN5 : LPC_AD0

PIN6 : LPC_SERIRQ_R

PIN7 : LPC_AD1

PIN8 : +5V

PIN9 : LPC_AD2

PIN10 : NC

PIN11 : LPC_AD3

PIN12 : GND

PIN13 : LPC_FRAME#

PIN14 : GND

JLPC1

PIN1: NC PIN7: LPC_FRAME#

PIN2: +3.3V PIN8: LPC_AD0

PIN3: LPC_AD3 PIN9: No pin

PIN4: PLTRST_SIO# PIN10: GND

PIN5: LPC_AD1 PIN11: CK_25M_SIO_R

PIN6: LPC_AD2 PIN12: GND

2.2.7 Daugherboard Internal Connector and PIN Definition

Label Function Note

JLED_OUT

PIN1: PLED

PIN2: SLED

JUSB2_CAMERA

PIN1: GND

PIN2: USB_HB_CM_N3

PIN3: USB_HB_CM_P3

PIN4: +5V_USB789

JUSB2_MSR

PIN1: GND

PIN2: USB_HB_CM_N2

PIN3: USB_HB_CM_P2

PIN4: +5V_USB789

COM0_OUT/

COM1_OUT

PIN1 : C1_RID#

PIN2 : No pin

PIN3 : COM1_RTS#

PIN4 : COM1_CTS#

PIN5 : GND

PIN6 : COM1_DSR#

PIN7 : COM1_TXD

PIN8 : COM1_DTR#

PIN9 : COM1_DCD#

PIN10: COM1_RXD

JLVDS_IN_30P



PIN3 : Conv_SRC PIN8 : LVDS2A_CLK_P







PIN10 : LVDS2A_CLK_N PIN25:LVDS2_EDID_DATA

13






JLVDS_IN_40P

PIN1 : +12V PIN21: LVDSA_N3


PIN3 : LVDS1_VDD PIN23: GND

PIN4 : +12V PIN24: GND

















JCONV1

PIN1: Conv_SRC

PIN2: Conv_SRC

PIN3: GND

PIN4: BL_EN2

PIN5: BRIGHT2

PIN6: GND

JLVDS_OUT_40P



PIN3 : LVDS1_VDD PIN23: GND

PIN4 : +12V PIN24: GND

















JLVDS_OUT_30P



PIN3 : Conv_SRC PIN8 : LVDS2A_CLK_P







PIN10 : LVDS2A_CLK_N PIN25:LVDS2_EDID_DATA






14

TOUCH2

PIN1: THY+

PIN2: THY-

PIN3: THOROBE_R

PIN4: THX-

PIN5: THX+

JUSB2_RESV

PIN1: GND

PIN2: USB_HB_CM_N4

PIN3: USB_HB_CM_P4

PIN4: +5V_USB789

JTOUCH1

PIN1 : +5V_RS232

PIN2 : +3.3V

PIN3 : 232_RX

PIN4 : 232_TX

PIN5 : GND

COM0_IN/

COM1_IN

PIN1 : COM1_DCD#

PIN2 : COM1_RXD

PIN3 : COM1_TXD

PIN4 : COM1_DTR#

PIN5 : GND

PIN6 : COM1_DSR#

PIN7 : COM1_RTS#

PIN8 : COM1_CTS#

PIN9 : C1_RID#

PIN10: No pin.

JUSB1

PIN1: USB_HB_CM_P4 PIN7: USB_HB_CM_P2

PIN2: +5V_USB789 PIN8:USB_HB_CM_P3

PIN3: USB_HB_CM_N4 PIN9 : USB_HB_CM_N2

PIN4: +5V_USB789 PIN10: USB_HB_CM_N3



JLED_IN

PIN1: PLED

PIN2: SLED

15

3. BIOS Setup Program

This motherboard supports a programmable firmware chip that you can update using the

provided utility. Use the BIOS Setup program when you are installing a motherboard,

reconfiguring your system, or prompted to “Run Setup.” This section explains how to

configure your system using this utility.

Even if you are not prompted to use the Setup program, you can change the configuration

of your computer in the future. For example, you can enable the security password feature

or change the power management settings. This requires you to reconfigure your system

using the BIOS Setup program so that the computer can recognize these changes and

record them in the CMOS RAM of the firmware hub.

The firmware hub on the motherboard stores the Setup utility. When you start up the

computer, the system provides you with the opportunity to run this program. Press <Del>

during the Power-On-Self-Test (POST) to enter the Setup utility; otherwise, POST

continues with its test routines.

If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or

by pressing the reset button on the system chassis. You can also restart by turning the

system off and then back on. Do this last option only if the first two failed.

The Setup program is designed to make it as easy to use as possible. Being a menu-driven

program, it lets you scroll through the various sub-menus and make your selections from

the available options using the navigation keys.

� The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Optimized Defaults from the BIOS menu screen.

� The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

� Visit the system builder’s website to download the latest BIOS file for this motherboard

16

Legend Box

The keys in the legend bar allow you to navigate through the various setup menus

Key(s) Function Description

→← Select Screen

↑↓ Select Item

Enter Select

+ - Change Opt.

F1 General Help

F2 Previous Values

F3 Optimal Defaults

F4 Save and Exit

ESC Exit

List Box

This box appears only in the opening screen. The box displays an initial list of configurable

items in the menu you selected.

Sub-menu

Note that a right pointer symbol appears to the left of certain fields. This pointer

indicates that you can display a sub-menu from this field. A sub-menu contains additional

options for a field parameter. To display a sub-menu, move the highlight to the field and

press <Enter>. The sub-menu appears. Use the legend keys to enter values and move

from field to field within a sub-menu as you would within a menu. Use the <Esc> key to

return to the main menu.

Take some time to familiarize yourself with the legend keys and their corresponding

functions. Practice navigating through the various menus and submenus. If you

accidentally make unwanted changes to any of the fields, press <F3> to load the optimal

default values. While moving around through the Setup program, note that explanations

appear in the Item Specific Help window located to the right of each menu. This window

displays the help text for the currently highlighted field.

17

BIOS Menu Screen

When you enter the BIOS, the following screen appears. The BIOS menu screen displays

the items that allow you to make changes to the system configuration. To access the menu

items, press the up/down/right/left arrow key on the keyboard until the desired item is

highlighted, then press [Enter] to open the specific menu.

18

3.1 Main Setup

This menu gives you an overview of the general system specifications. The BIOS

automatically detects the items in this menu. Use this menu for basic system configurations,

such as time, date etc.

BIOS Information

Displays the auto-detected BIOS information.

� System Date

The date format is <Date>,<Month>,<Day>,<Year>.

� System Time

The time format is <Hour>,<Minute>,<Second>.

19

3.2 Advanced BIOS Setup

Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen.

You can select any of the items in the left frame of the screen, such as Chipset

configuration, to go to the sub menu for that item. You can display an Advanced BIOS

Setup option by highlighting it using the <Arrow> keys. All Advanced BIOS Setup options

are described in this section. The Advanced BIOS Setup screen is shown below. The sub

menus are described on the following pages.

Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.

20

ACPI Settings

� Enable Hibernation [Enable]

Enable or Disable system ability to hibernation.

� ACPI Sleep State [S3 (Suspend to RAM)]

Select the highest ACPI sleep state the system will enter the SUSPEND button is

press. Configuration options: [Suspend Disable] [S3 (suspend to RAM )]

21

Super IO configuration

� Serial Port 1~7 Configuration

Set Parameters of Serial Port 1~7

22

� Serial Port [Enable]

Enable or Disable Serial Port

� Change Settings [Auto]

Select an optimal setting for Serial Port. You can decide IO and IRQ by yourself.

Suggest to leave this option “Auto”

� COM1~7 Voltage [0V]

Select 0V, 5V, 12V voltage for serial port

Parallel Port Configuration:

� Parallel Port [Enable]

Enable or Disable Parallel Port (LPT/LPTE)

� Change Settings [Auto]

Select an optimal setting for Parallel port device. Suggest to leave this option “Auto”

� Device Mode [ STD Printer Mode]

Change the printer mode: [STD Printer Mode][SPP Mode][EPP-1.9 and SPP

Mode][ EPP-1.7 and SPP Mode][ECP Mode][ECP and EPP 1.9 Mode][ECP and EPP

1.7 Mode]

23

� CASH Drawer Voltage:

Select 0V, 12V, and 24V for cash drawer device

Cash Drawer Control in GPIO port:

Open Drawer

Write “87”h to I/O Port “2E”h



Write “07”h to I/O Port “2F”h

Write “E5”h to I/O Port “2E”h


Close Drawer







Detect Drawer Satus



24




Read I/O “2F”h

Definition(bit3)

� Deep Sleep Function]Disabled]:

Select to Enable/Disable Deep Sleep S5 function. When select to Enabled, Only

Power Button can power on the system

25

PC Health Status

Display the system information including temperature and voltage.

� Smart Fan Function [Enable]

Enable or Disable the Smart FAN

� Smart Fan Function

When Enter this sub-menu. You can choose the mode of smart Fan.

Option:[ Manual Mode][Thermal Cruise Mode]

26

� Digital IO configuration

You can configure Digital I/O pin1~3 this this sub-menu

� Case Open warning[Disable]

Enable or Disable Case Open warning

Configuration options: [Disabled] [Enabled]

� Watch Dog Timer[Disable]

Enable or Disable watch dog timer function. After enabling this function, you can set

watch dog timer count mode and time out value like below.


27

S5 RTC wake up

setting

� Wake system from S5 [Disable]

Enable or Disable system wake on alarm event. Select FixedTime, system will wake on

the hr :min ::sec specified.. After you enable this funciton, you can see the screen like

below.

28

PC Health Status

Display Intel Trusted Execution Technology configuration.

29

� Display CPU information

� Limit CPUID Maximum [Disable]

Disable for Windows XP

Configuration options: [Disable] [Enable]

� Execute Disable Bit [Enable]

XD can prevent certain classes of malicious buffer overflow attacks when combined

with a supporting OS(Windows server 2003 SP1, WindowsXP SP2, SuSE Linux 9.2,

Redhat Enterprise 3 update 3.)


� Intel virtualization technology [Enable]

When enabled, a VMM can utilize the additional hardware capabilities provided by

Vanderpool Technology


PPM configuration

� S0ix [Enable]

Enable/Disable CPU S0ix state


30

IDE Configuration

Display and set IDE related device configuration.

� Serial-ATA(SATA) [Enable]

nable/Disable Serial ATA


� SATA Speed Support [Gen2]

SATA speed support Gen1 or Gen2

Configuration options: [Gen1] [Gen2]

� SATA mode [IDE mode]

Select IDE or AHCI

Configuration options: [IDE mode] [AHCI mode]

� Serial-ATA Port1 [Enable]

Enable/Disable Serial ATA port1

Configuration options: [Enable][Disable]

� Serial-ATA mSATA [Enable]

Enable/Disable Serial ATA mSATA


31

Miscellaneous Configuration

Display miscellaneous configuration.

� High Precision Timer [Enable]

Enable or Disable the High Precision Event Timer


� OS Selection[Windows 7]

OS selection

Configuration options: [Win8.X] [Windows 7]

32

Network Stack Configuration

Network Configuration and setup

� Network Stack [Enabled]

Enable/Disable UEFI Network Stack.

Configuration options: [Enabled] [Disabled]

� Ipv4 PXE support [Enabled]

Enable Ipv4 PXE boot Support. If disabled, IPV4 PXE boot option will not be created.


� Ipv6 PXE support [Enabled]

Enable Ipv6 PXE boot Support. If disabled, IPV6 PXE boot option will not be created.


� PXE boot wait time

Wait time to press ESC key to abort the PXE boot

33

Compatibility Support Module Configuration

� CSM Support [Enabled]

Enable/Disable CSM Support

Configuration options: [Enable] [Disable]

� GateA10 Active[Upon Request]

Upon request-GA20 can be disabled using BIOS services. Always- Do not allow

disabling GA20; this option is useful when any RT code is executed above 1MB.

Configuration options: [Upon request] [Always]

� Option ROM messages[Force BIOS]

Set Display mode for option ROM

Configuration options: [Force BIOS] [Keep Current]

� INT19 Trap Response[immediate]

BIOS reaction on INT19 trapping by option ROM: Immediate- execute the trap right

away; postpone- execute the trap during legacy boot.

Configuration options: [Immediate] [Postpone]

� Boot option Filter[UEFI and legacy]

This option controls legacy/UEFI ROMs priority.

Configuration options: [UEFI and legacy] [legacy only]

� Networks[legacy]

Controls the execution of UEFI and legacy PXE OpROM

Configuration options: [Do not launch] [UEFI][Legacy]

34

� Storage[legacy]

Controls the execution of UEFI and legacy Storage OpROM


� Video[legacy]

Controls the execution of UEFI and legacy video OpROM


� Other PCI devices[legacy]

Determine OpROM execution policy for devices other than Network, Storage, or Video

Configuration options: [UEFI][Legacy]

USB Configuration

� Legacy USB Support [Enabled]

Enable Legacy USB support. Auto option disables legacy support if no USB devices

are connected. Disable option will keep USB devices available only for EFI application

Configuration options: [Enable] [Disable][Auto]

� XHCI hand-off[Enable]

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership

change should be claimed by XHCI driver.

35


� EHCI hand-off[Enable]

This is a workaround for OSes without EHCI hand-off support. The EHCI ownership

change should be claimed by XHCI driver.


� USB Mass storage[Enable]

Enable/Disable USB mass storage driver support.


� USB Transfer time-out[20sec]

The time-out value for Control, bulk, and interrupt transfers.

Configuration options: [1sec] [5sec][10 sec][20sec]

� Device reset time-out[20sec]

USB mass storage device start unit command time-out.

Configuration options: [10sec] [20sec][30 sec][40sec]

� Device power-up delay[Auto]

Maximum time the device will take before it properly reports itself to the Host controller.

Auto’ uses default value: for a Root port it is 100ms, for a Hub port the delay is taken

from Hub descriptor.

Configuration options: [Auto] [manual]

36

Driver healthy

Provide the Health status of the drivers and controllers.

37

3.3 Chipset

North Bridge :

Intel IGD configuration :

38

� DVMT Pre-allocated [64MB]

Select DVMT 5.0 Pre-allocate(Fixed0 Graphic memory size used by the internal

graphic device.

Configuration options: Min: [64M] to Max:[512M]

� DVMT Total Gfx Mem[256MB]

Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphic device.

Configuration options: [128MB] [256MB][Max]

� Aperture size[256MB]

Select the aperture size

Configuration options: [128MB] [256MB][512MB]

39

LCD control :

� Primary IGFX Boot [CRT]

Select the Video Device which will be activated during Post. This has no effect if

external graphics present. Secondary boot display selection will appear based on your

selextion. VGA modes will be supported only on primary display.

Configuration options: [VBIOS Default][CRT][eDP/LVDS1][DP/LVDS2]

� Secondary IGFX Boot[eDP/LVDS1]

Select secondary display device.

Configuration options: [VBIOS Default][CRT][eDP/LVDS1][DP/LVDS2]

� LVDS1 Panel Type [1024x768(24bit]]

Select the resolution of LVDS1

Configuration options: [disable]or different resolution

� LVDS2 Panel Type [Disable]

Select the resolution of LVDS2

Configuration options: [disable]or different resolution

� Max T0LUD

Maximum Value of T0LUD

Configuration options: [Dynamic][2GB][2.25GB][2.5GB][2.75GB][3GB]

40

South Bridge :

41

Azalia HD audio :

� Audio Controller [Enable]

Control Detection of the Azalia device. Disabled=Azalia will be unconditionally disabled.

Enabled= Azalia will be unconditionally Enabled. Auto= Azalia will be enabled if

present disabled otherwise.


� Amplifier GAIN(db)

Select Amplifier GAIN value

onfiguration options: [15.3db][21.2db][27.2db][31.8db]

42

USB configuration :

� XHCI Mode [Auto]

Mode of operation of XHCI controller

Configuration options: [Enable][Disable][Auto][Smart Auto]

� USB2 Link Power[Enabled]

Enable/Disable USB2 Link Power management

Configuration options: [Enabled][Disabled]

43

� High Precision Timer [Enabled]

Enable or Disable the High precision Event Timer


� Onboard LAN control[Enabled]

Enable/Disable the LAN


� Onboard LAN BootROM[Disabled]

Enable/Disable the boot option for LAN controller


� PCIE Wake [Disabled]

Enable or disable PCIE to wake the system from S5


� Restore AC power loss[power off]

Select AC power state when power is re-applied after a power failure

Configuration options: [Power off][Power on][Last state]

44

3.4 Security

� Administrator Password

Set setup Administrator Password

� User Password

Set User Password

45

3.5 Boot

� Setup Prompt Timeout [1]

Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite

waiting.

� Bootup NumLock State [On]

Select the keyboard NumLock state

Configuration options: [On] [Off]

� Quick Boot [Disable]

Enable or disable Quick Boot option


� Fast Boot [Disable]

Enable or disable boot with initialization of a minimal set of devices required to launch

active boot option. Has no effect for BBS boot options.


� Boot mode select [LEGACY]

Select boot mode LEGACY/UEFI

Configuration options: [LEGACY] [UEFI]

� Fixed boot order priorities

Define the boot priorities 1~8 in these option

46

3.6 Save & Exit

� Save changes and Exit

Exit system setup after saving the changes.

� Discard changes and Exit

Exit system setup without saving the changes.

� Save changes and Reset

Reset the system after saving the changes.

� Discard changes and Reset

Reset the system without saving the changes.

� Restore Defaults

Restore/Load default values for all the setup option.

� Launch EFI shell from filesystem device

Attempts to launch EFI shell application (shell.efi) from one of the available filesystem

devices.

47

� Reset system with ME disable ModeMEUD000

ME will runs into the temporary disable mode, Ignore if ME ignition FWMEUD001.

IBAYT-PBL3(motherboard card) AD1040(daughter...

Documents

Transcript of IBAYT-PBL3(motherboard card) AD1040(daughter...