HulaminCatalogue.pdf

Standard Profile Catalogue

August 2007

Note:All the information has been provided in good faith. However, if there is an error in the information, whether due to the negligence of the company or otherwise, the company cannot accept liability for any loss caused by such an error. Similarly, the company accepts no liability of any nature whatsoever, whether arising through damage or loss caused by the customer's negligence or other fault.

Hulamin Extrusions reserves the right to modify any specifications and/or dimensions without prior notice in the interest of product development.

www.hulaminextrusions.co.za

Prev

Next

Pg 5

http://www.hulaminextrusions.co.za

Introduction

SynopsisThis Hulamin Extrusions Standard Profile Catalogue lists the range of standard profiles available at the time of going to press.

RangeThe range of extrusions available is constantly changing and enquiries for shapes not listed can be made through any one of our sales offices. Please also refer to our website, www.hulaminextrusions.co.za for the latest version of this catalogue.

ShapeAll dimensions are expressed in millimetres. Fully dimensioned die drawings are available from any one of our sales offices which can provide complete details of any section required.

MassAll profile masses are expressed in kilograms per metre.

Prev

Next

Pg 5

Company Profile

Hulamin Extrusions, formerly known as Hulett-Hydro

Extrusions, is South Africa's leading extruder. Operating out of three plants in Johannesburg, Pietermaritzburg and Cape Town, the company has 40 years experience in developing and servicing the South African market and exporting to customers around the world. The founding shareholder of the company was Alcan.

The expertise in Hulamin Extrusions emanates from its two shareholders:

?Hulamin (formerly Hulett Aluminium), has long been South Africa's leading producer of rolled and extruded aluminium.

?Hydro Aluminium Extrusions, in 1997 bought a share in the company in order to establish itself in the expanding Sub-Saharan African Market.

In April 2007, Hulett Aluminium changed its name to Hulamin, and as a result Hulett-Hydro Extrusions changed its name to Hulamin Extrusions.

International Service

Our mission at Hulamin Extrusions is to consolidate our position as Southern Africa's leading extruder and supplier of quality extrusions locally and internationally. Our customer base today extends into the demanding engineer-ing markets within the UK, Europe and North America, where on-shore representation ensures excellent customer service is provided by experienced, dedicated personnel.

In South Africa we are the leader in developing extrusion applications in a diverse range of markets.

Quality from start to finish

Hulamin Extrusions operates a quality system approved to ISO 9001.2000, dimensional tolerances based on EN 755. This system allows quality management from an initial contract review through to product shipment – literally from start to finish on each enquiry. Laboratory facilities are also available to assist with quality issues and any necessary metallurgical testing.

Hulamin Extrusions has a proud record of extrusion supply, both locally and throughout the world. Our ongoing commitment is to quality and customer service.

Prev

Next

Pg 5

Contents

How to order 5The Properties of Aluminium 6Alloys 7Technical Information 7Technical Grade 11Manufacturing Limits 11Dimensions 12Lengths 12General 13Forms of Corrosion 13Corrosion Resistance in Different Environments 14Surface Treatment 14

AnglesType 1 15Type 2 16Type 3 16Type 4 17Type 5 20Type 6 20Type 13 21

ChannelsType 1 22Type 2 25Type 3 26Type 4 26Type 5 27Type 7 27Type 11 27Type 15 27

Extruded Rods 28Extruded Tubes 29Flat Bars

Type 1 33Type 2 36Type 3 36

Square Bars 37Hexagonal Bars 37Rectangular Hollows 38Square Hollows 42I - Sections 44Tees

Type 1 45Type 2 46

Z - Sections 46

Engineering Data for Structural Shapes 47Angle

Type 1 47Type 2 51Type 3 52Type 4 53Type 6 58

ChannelType 1 59Type 2 65Type 3 66

I - Sections 67Tees

Type 1 69Type 2 70

Index 71

4Hulamin Extrusions Standard Profile Catalogue August 2007

Prev

Next

5 Hulamin Extrusions Standard Profile CatalogueAugust 2007

How to order

Essential information required for entry of enquiries or orders

Complete specifications:?Alloy/condition?drawing number/die number?lengths?special tolerances?finishing requirements (type, colour and micron thickness of anodising)?powder coating requirements and any other fabrication related specification detail to ensure material conforms to detailed

requirements.

Additional information:?End use: Brief detail on end use of material.?Delivery requirements: State specific delivery requirements.

PackingUnless otherwise specified on the order, normal Hulamin Extrusions packing methods will be used.

Shipping tolerancesExtruded products will, within practical limits, be supplied in the number of pieces ordered. Unless otherwise stated, orders for production by Hulamin Extrusions will be subject to a mass or piece quantity tolerance of ± 10%.

If over-shipment is not permissible the order shall be endorsed ”Do not over-ship mass” (or “Pieces” as is applicable) in which case an under-shipment of 10% may be supplied.

Supply of an exact number of pieces or other shipping tolerances closer than those stated will be subject to enquiry, and may incur a price premium.

Other requirementsOrders should be clearly detailed with any special requirements.

Minimum acceptable quantities per itemThe process is such that a minimum length of extrusion emerges from the extrusion cycle. This results in certain minimum quantities being readily produced. All enquiries will be handled by our sales offices who will advise on minimum quantities. A price premium is applied to small orders.

MassesThe masses shown for sections in this catalogue are for guidance and may vary slightly according to the alloy and the dimensional accuracy achieved within the permissible tolerances.

Prev

Next

Pg 5

6

Aluminium’s physical properties compared to other common construction materials.

Aluminium 6063 Copper Steel 371 Plastic

Hulamin Extrusions Standard Profile Catalogue August 2007

225

10 to 24

69 000

2 700

600 to 655

-250 to 150

35

200

23

Yes

Yes

250

25

125 000

8 900

1 080

-200 to 300

55

400

17

Yes

Yes

400

20

210 000

7 800

1 500

-50 to 500

7

76

12

No

Yes

50

25

3 000

1 400

80

-50 to 80

-

0,15

60 to 100

Yes

Yes

Strength / Breaking strength MPa

Ductility / Expansion %

Elasticity E, Young’s modulus MPa3Density kg/moMelting point C

Working temperature range2Electrical conductivity m/Ohm-mm

Heat conductivity W/mK E-06 oCoefficient of linear expansion x 10 /C

Non-magnetic

Weldable

The properties of aluminium

Aluminium has a unique and unbeatable combination of pro-perties that make it a versatile, highly usable and attractive construction material.

MassAluminium is a light metal with a density of 2,700 kg/m3, one third that of steel.

StrengthAluminium is strong with a tensile strength of 70 to 700 Mpa, depending on the alloy and manufacturing process. Extru-sions of the right alloy and design are as strong as structural steel.

ElasticityThe Young's modulus for aluminium (E=69000 Mpa) is a third that of steel. This means that the moment of inertia has to be three times as great for an aluminium extrusion to achieve the same deflection as a steel profile.

FormabilityAluminium is very easy to machine. Ordinary machining equipment can be used such as saws and drills. Aluminium is also suitable for forming in both the hot and the cold condition.

JoiningAluminium can be joined using all the normal methods avail-able such as welding, brazing, adhesive bonding and riveting.

Corrosion resistanceA thin layer of oxide is formed when exposed to air. This pro-vides very good protection against corrosion even in corrosive environments. This layer can be further strengthened by sur-face treatments such as anodising or powder coating.

ConductivityThe thermal and electrical conductivities are very good even when compared with copper. Furthermore, an aluminium conductor has only half the weight of an equivalent copper conductor.

Linear expansionAluminium has a relatively high coefficient of linear expan-sion compared to other metals. This should be taken into account at the design stage to compensate for differences in expansion.

Non-toxicAluminium is non-toxic and is therefore highly suitable for the preparation and storage of food.

ReflectivityAluminium is a good reflector of both light and heat. Prev

Next

Pg 5

7

Alloy Nomenclature

Alloy Designations

Guaranteed Mechanical Properties - Extruded Products

Important:The four-digit system of alloy nomenclature used by Hulamin Extrusions, in common with the Aluminium Federation, uses a block number to indicate the main alloying constituents.

Alloys

Technical Information

1xxx2xxx3xxx4xxx5xxx6xxx7xxx

Alloy

Series

SiliconMagnesium

Magnesium and SiliconZinc, Magnesium and/or Copper

Main alloying constituentAluminium, 99.0% minimum and greater

CopperManganese

Alloy EN Equivalent Previous German Equivalent

1070A Al 99.7 Al 99.76063 Al Mg0.7Si AlMgSi 0.5 F22

6063A Al Mg0.7Si(A) AlMgSi 0.5 F256463 Al Mg0.7Si(B) -

6101A Eal MgSi(A) E-AlMgSi 0.56061 Al MgSiCu -6082 Al Si1MgMn AlMgSi 16005 Al SiMg AlMgSi 0.7

1070A F - All - 60 - 25 23O - 100 - - 130 18 16T4 - 25 65 120 - 14 12T5 - 3 130 175 - 8 6T5 3 25 110 160 - 7 5T6 - 10 170 215 - 8 6T6 10 80 160 195 - 8 6O - 100 - 150 - 16 14T4 - 25 90 150 - 12 10T5 - 25 160 200 - 7 5T6 - 25 190 230 - 7 5T4 - 50 75 125 - 14 12T6 - 50 160 195 - 10 8

6101A T6 - 50 160 215 - 8 6O - - - - 150 16 14T4 - 25 110 180 - 15 13T6 - 5 240 260 - 8 6O - 100 - - 160 16 14F - 100 - 110 - 13 12T4 - 80 120 190 - 16 14T6 - 20 250 295 - 8 6T6 20 80 260 310 - 8 -T4 - 10 90 180 - - 13T6 - 5 215 255 - - 6T6 5 15 200 250 - - 6

6082

6005

6063

6063A

6463

6061

0.2% Proof

stress Min

Mpa

Ultimate tensile strength Elongation Min

Max

Mpa

A%

Min

Auo mm

% mm

Min

Mpa

TemperAlloy

Thickness

Over

mm

Up to and

including mm

Hulamin Extrusions Standard Profile CatalogueAugust 2007

Prev

Next

Pg 5

8

Note: Single figures denote maximum content. Aluminium remainder. Other alloys may be available - subject to enquiry.

Alloy Compositions.

Si Fe Cu Mn Mg Cr Zn Ti Each Total1070A 0.2 0.25 0.03 0.03 0.03 - 0.07 0.03 0.03 -6063 0.2-0.6 0.35 0.10 0.10 0.45-0.90 0.10 0.10 0.10 0.05 0.15

6063A 0.3-0.6 0.15-0.35 0.10 0.15 0.60-0.90 0.05 0.15 0.10 0.05 0.156463 0.2-0.6 0.15 0.20 0.05 0.45-0.90 - 0.05 - 0.05 0.156061 0.4-0.7 0.4 0.15-0.40 0.20-0.35 0.70-1.00 0.10 0.20 0.10 0.05 0.156005 0.6-0.9 0.35 0.10 0.10 0.40-0.60 0.10 0.10 0.10 0.05 0.156082 0.7-1.3 0.5 0.10 0.40-1.00 0.60-1.20 0.25 0.20 0.10 0.05 0.15

AlloyPercentages Others

Tempers

Temper Description ApplicationF As fabricated Forging stock: Maximum formabilityO Annealed Forging stock: Maximum formability

T6 Solution heat-treated and artificially agedWhere highest mechanical properties are required

T4 Solution heat treated and naturally agedFormability with higher properties than F or O conditions

T5Cooled from an elevated shaping process and

artificially agedWhere highest mechanical properties are not required by end use (i.e. non-structural)


The choice of material is a critical decision in all product de-velopment. Aluminium makes it possible to give the product suitable physical and mechanical properties at the same time as achieving an aesthetically attractive appearance.

Furthermore, the extrusion technique, combined with the right alloy and proper thermal treatment, offers an infinite number of application opportunities. It also forms the basis for product improvement. Pure aluminium is only used in a limited way commercially. The majority of extrusions are made from aluminium alloyed with other metals.

The most common elements used are magnesium (Mg), silicon (Si), manganese (Mn), zinc (Zn) and copper (Cu). They form between 0.2 and 0.7 per cent of aluminium alloys.

Aluminium alloys used for extrusions are generally with the following serial numbers:1000 series - Al6000 series - Al + Mg + Si

The 1000 series is not heat treatable. These alloys are often chosen in products where high thermal and electrical con-ductivity are desired. They have low strength.

The 6000 series are heat treatable. They are the most com-monly used extrusion alloys and have a wide range of appli-cations.

The 6000 series has good extrudability and can be solution heat treated at the extrusion temperature. Furthermore, these alloys have medium to high strength, are easy to weld and offer good resistance to corrosion, even in marine en-vironments. The bulk of the extruded material for load bear-ing constructions is made from these qualities. They are used for load bearing constructions both on land and at sea.

The 6063 alloy offers medium strength and is easy to extrude even for complicated cross sections. This alloy is one of the most used extrusion alloys. It has good formability during bending in the T4 condition. Typical applications are extru-

sions for windows and doors, lighting, awnings, handrails and furniture. This material is highly suitable for anodising, both for decorative and protective reasons.

The 6005 alloy has higher strength than 6063 but is slightly harder to extrude. The material withstands comparatively little elon-gation before there is permanent deformation in the heat treated condition. This alloy can be exposed to greater inter-crystalline corrosion than 6063 and 6082, it is suitable for anodising for protective purposes but the quality of the surface make decorative finishing more difficult.

The 6061/6082 alloys have high strength qualities and are suitable for extrusion of cross-sections that are not too com-plicated. Typical applications are load carrying structures in ships, offshore transport, and the building industry such as platforms, bridges, stairs, scaffolds and handrails. The material is suitable for anodising for protective purposes.

Temperature – mechanical propertiesCare should be taken when using aluminium at high tempera-tures. Mechanical properties could significantly be reduced at temperatures above 100°C, especially if the material has been thermally hardened or cold worked.

In general the 6063, 6005, 6061 and 6082 alloys should not be used in structures at temperatures above 100°C. The tensile strength decreases as the temperature increases while elong-ation on fracturing usually increases. It should be noted that the characteristics are dependent on alloy, temperature, and time. If the designer is unfamiliar with the exact temperature characteristics for a given alloy, it can be assumed as a starting point that properties such as tension, shear and fatigue strength vary in proportion to the tensile strength.

Low temperature propertiesIn contrast to steel, aluminium alloys do not become brittle at low temperatures. In fact aluminium alloys increase in strength and ductility whilst impact strength remain unchanged. As the temperature decreases, below 0°C, the yield strength and tensile strength of aluminium alloys increase.

Prev

Next

Pg 5

9

Summary of Alloys

Values for the mechanical properties can vary for different process parameters. The values given are typical and can be guaranteed on the assumption that a special agreement has been reached.

The relationship between some accepted methods for measuring hardness.

Brinell

Vickers

Rockwell ‘F’

Rockwell ‘E’

Rockwell ‘B’

Rockwell ‘K’

Webster

Hardness Number

45 50 55 60 65 70 75 80 85 90 95 100 105 110

46 51 56 61 66 71 76 82 87 92 98 103 109 115

36 46 54 61 67 71 76 79 82 85 87 89 91

47 55 62 68 72 77 80 83 86 88 90 92 94 96

12 23 32 39 45 50 56 60 63 66

15 25 35 41 48 53 58 62 66 70 73 76 78

13121110975 13-14 14-25 15 15-16 16 16-17 17

- - - -

-

-


Hulamin Extrusion Alloys Condition 1070A 6063 6005 6061 6082

O 20 - - - -F 25 - - - -T4 - 95 70 145 125T6 - 225 260 275 290O 75 - - - -F 80 - - - -T4 - 190 160 220 225T6 - 250 285 310 315T4 - 24 22 20 20T6 - 10 8 10 10T4 - 47 47 65 65T6 - 81 92 100 100

2 700 2 700 2 700 2 700 2 71069 000 69 000 69 000 69 000 69 000

Electrical conductivity % IACS - 62 52 52 46 46

Melting Point (oC) - 645-658 600-655 615-655 580-650 580-650EN-AW 6063A 6005A 6061 6082

Yield strength, Mpa

Tensile strength, Mpa

Elongation, A5 %

Brinell Hardness, HB

Density (kg/m2) Young's Modulus (Mpa)Coefficient of expansion

20-100oC (oC-1)- 24E-06 23E-06 23E-06 24E-06 23E-06

200 180 180Thermal conductivity

20oC (W/mK)- 229 200

Prev

Next

Pg 5

10

Metal Thickness Chart

Definitions

1. Flat solid shapes:Shape to be basically flat.Thickness to be uniform.No dovetails or screw receiving slots.

2. Regular solid shapes:1 3H = /D W = /D3 4

Medium depth channels:1 3H = /D W = /D3 4

3.

Deep solid channels:1 3H = /D W = /D3 4

4.

DH

W

Sem

i-hol

low a

nd h

ollo

w shap

es

Deep s

olid c

hann

els (4

)

Medium depth channels,

angles, tees (

3)

Regular solid shapes (2)

Flat solid shapes (1)

4.00

3.80

3.60

3.40

3.20

3.00

2.80

2.60

2.40

2.20

2.00

1.80

1.60

1.40

1.20

4.00

3.80

3.60

3.40

3.20

3.00

2.80

2.60

2.40

2.20

2.00

1.80

1.60

1.40

1.20

20 40 60 80

100

120

140

160

180

200

220

240

260

280

mm

Diameter of Circumscribing Circle (D)

Min

imum

rec

omm

ende

d m

etal

thic

knes

s (T

)

Min

imum

rec

omm

ende

d m

etal

thic

knes

s (T

)

mmmm


Prev

Next

Pg 5


Technical GradeTechnical grade implies that the following tests will be carried out.

Ultrasonic testingThe aluminium billet to be used will be ultrasonically tested to a pre-determined level to detect inclusions and cracks. Should a customer require the billet to be to a higher standard, the standard of acceptance shall be agreed with the customer prior to manufacture and clearly stated on the order.

Etch test piecesFor extruded lengths or bars or sections produced, test pieces of the full cross-section shall be taken from the front end and back end of the extruded length. The specimen shall be suitably prepared, etched and inspected. The etched sur-

?face shall be free from harmful defects . If any specimen reveals a harmful defect, the relevant length of bar or section shall be scrapped.

?Definition - Harmful defects in the above context refers to any physical defect such as cracks and over extrusion, which can be seen with the naked eye. It is up to the pur-chaser to inform the manufacturer of any other possible defects for which the product should be checked.

Longer than normal discardsFor each billet extruded, a longer than normal discard will be set and maintained so as to obviate the risk of over extrusion.

Drift testingAll hollow sections with wall thickness up to 12 mm produced by the porthole type extrusion die shall have test pieces cut from every extruded length. Test pieces shall be subjected to an expansion test to determine the soundness of the extruded seam welds. HE can however not provide a 100% guarantee on the weld soundness even though the above testing has been carried out. It is the responsibility of the end user to ensure that the product is entirely suitable for its intended use. Profiles with wall thickness greater than 12 mm cannot be drift tested.

TraceabilityAll test pieces and heat treatment records relating to Tech-nical Grade lots are kept for a period of six months and five years respectively to enable traceability and ongoing evalu-ation of quality.

Manufacturing Limits

General NotesManufacturing limits are imposed by available production facilities and also by the nature of the extrusion process. The size and power of available extrusion presses limit the overall cross-sectional dimensions of sections. The stretching, hand-ling and heat-treatment equipment limit cross-sectional areas and lengths. Lengths may also be limited by transport restrictions. Minimum thickness, shape configuration and complexity of detail may be limited by the extrusion process as well as by press capacity. Manufacturing limits for sections of complicated shape and abnormal design may be narrower than stated. The limits given are for sections designed accor-ding to accepted extrusion design practice. The maximum circumscribing circle diameters given on are a guide and must not be read as being available at the minimum thickness shown in the adjacent column. A guide as to this ratio of circumscribing circle to minimum thickness may be obtained from the diagram on Page 10. The maximum limits as dictated by press capacity, are given on Page 12.

Manufacturing TolerancesAs with all manufacturing and fabrication processes, the pro-cess whereby aluminium is extruded sets a range of manufac-turing tolerances within which aluminium extrusion products can be expected to vary.

The extrusion process is remarkable in its ability to produce lengths of intricate shapes within close shape and dimen-sional tolerances. Normal deviations are proved to be small and to have little impact in a very wide range of applications. Although dies are produced to exact size with virtually no tolerances allowed in manufacture, the extruded profile emer-ging from the die is subject to:

?Extrusion flow effects (influenced by die design and shape design)

?Cooling effects (both cooling medium and profile design can lead to irregular cooling)

?Handling effects (transfer and stretching)

Minor deviations to shape and size can be expected to occur no matter how experienced the die designer, how good the handling equipment or how well-trained the operating staff. It is against this background that extrusion tolerances need to be part and parcel of the extrusion process. In no way are published tolerances to be seen as the extruder's choice of how accurately he decides or wishes to work. Rather, extru-sion tolerances need to be seen and understood to be the range of shape and dimensional variations, which can be expected from the process.

The choice open to the extruder faced with requests for closer than standard or published tolerances depends on the nature of the request.

?If a metal dimension is involved, i.e. across the web of a channel, the prospects are good that closer than normal tolerances may be achieved provided the dimension is measurable. Shorter die life is likely to be incurred because the die may need to be replaced earlier than normally is the case, due to die wear.

?If a space dimension is involved, i.e. the width across the open flanges of a channel. Only in exceptional cases where it is vital for an assembly, will closer than Data Book tolerances be considered.

The straightness of a length of extrusion can depend on the degree to which the shape can be stretcher-straightened without incurring shape distortion. A compromise between straightness and shape may result. Both straightness and twist can be influenced by imbalance of the shape itself.

It is most important that new users of extruded products are aware from the design stage that machining tolerances can-not be expected from the extrusion process. All too often de-signers and draughtsman have had experience of machine shop tolerances only and need guidance in the understan-ding of extrusion tolerances or they are likely to specify the tolerances they are most familiar with. This can result in needless communications with producer plants, possibly obscuring, as a result, very real needs a designer may have for closer than normal tolerances.

The time to discuss extrusion tolerances is thus at the design stage rather than after delivery of the product which may be found to be difficult to use because allowance has not been made for normal tolerances.

Prev

Next

Pg 5

12

Maximumcircumscribing

circlediameter mm

Alloy

Minimumthicknessmm (2)

Range of cross-sectional areas and weight

Maximum Minimum

Area2mm(3)

Masskg/m

Area2mm

Masskg/m

Dimensional Capability Guide

1.20

1.20

1.50

1.75

1.25

1.25

1.50

1.751.60


5000

5000

5000

5000

5000

5000

5000

5000

13

13

13

13

13

13

13

13

26

29

55

55

55

55

195

195

0.07

0.08

0.15

0.15

0.15

0.15

0.53

0.53

320

320

320

320

200

200

200

200

1070A

6063

6061

6082

1070A

6063

6061

6082HO

LL

OW

SS

OL

IDS

The tolerances used by our extrusion plants as published in the Data Book are those published by the British Standards institute in BS EN 755.

Requests for tighter tolerances than these may be considered. Requests to produce to other specifications such as DIN, ASTM, BS EN 12020 and ISO will be considered but this must be made clear to the producing plant at the enquiry stage.

DimensionsNotes:

1.The manufacturing limits above are given as guidelines only and profiles outside of these limits may be available upon request.

2.The minimum thickness at which a section can be extruded is dependent on the alloy, circumscribing circle diameter, shape configuration and the complexity of detail. A guide to the relationship between circumscribing circle diameter and minimum wall thickness is shown on pg 10. The mini-mum thickness listed above does thus not relate to the maximum circumscribing circle diameters.

3.The maximum limit on cross-sectional area is imposed by extrusion ratio and stretching capacity. Sections of greater cross-sectional area may be supplied in the unstretched condition, on enquiry, but mechanical properties and straightness will not be guaranteed.

Hollow ProfilesTube and hollow shapes for the architectural and general engineering markets are produced by the porthole extrusion process. In this process the seam welds are formed in the dies during the extrusion process. Although considerable tonnages of hollow shapes and tubing are regularly and successfully extruded and put to good use, it is possible for weld soundness to be adversely affected by process factors. In spite of all measures normally taken during extrusion to achieve sound welds, the weld quality may vary along the extruded length. Notwithstanding the successful use made regularly of hollow shapes and tubing produced by the port-hole extrusion method, it is not possible to guarantee such welds. Drift testing as described in the section of Technical Grade, can be performed and gives a reasonable degree of assurance of the seam weld quality. However, this test can only be carried out on the ends of hollow profiles and tubes. Where physical injury or danger can result from seam weld failure, e.g. hang glider tubing, yacht masts, drift testing is

recommended. Where tubing is required to contain pressu-rised fluids, pressure testing is recommended before use.

Lengths

Maximum lengthsThe normal maximum straight length is 12 metres but 14,5 metre lengths may be available, subject to enquiry and de-pendent on transport conditions. Maximum length may also be limited by the maximum mass of section that can be supplied.

Minimum lengthsPieces less than 500 mm in length are generally available but are subject to enquiry.

Random lengthsWhere customer accepts random lengths and orders are en-dorsed accordingly, between 3 metres and 8 metres will be supplied. It is possible to supply most of an order to a length suitable to the customer within this range, and the balance only in random lengths.

Multiple LengthsSections can be supplied in multiples of the required unit length. In calculating the overall length an allowance of 5mm must be made for each saw cut.

Specified LengthsWhen a specified length is ordered, all lengths will be cut to specification within the limits of the length tolerance.

General

Products outside the limits outlined below will be subject to enquiry.

Tubing and Hollow Sections

Maximum LimitsMaximum Wall Thickness 12,0 mm Maximum Mass per Metre 13,0 kg/m

Minimum LimitsMinimum Tube Wall Thickness 1,2 mmMinimum Tube outside Diameter 10,0 mm

Prev

Next

Pg 5


Rod and Bar

Maximum Limits for Normal ExtrusionMaximum Diameter 80 mm (area 5 000 mm²)

Maximum Limits for Extrusion of Forging StockMaximum Diameter 100 mm (area 7 850 mm²)

Spreader Sections

All spreader sections are prone to defective areas at the front and back of each extruded length (apart from the front of the very FIRST billet during a production run), which necessitates the removal of a rejection of up to 3 metres of metal from the front and 1 metre from the back end of the pressed lengths.

Maximum Mass per Metre = 13,6 kg/mMaximum Length of a 13,6 kg/m section = 3,6 me.g. Maximum Length of a 10 kg/m section = 6,5 mMaximum Useable Billet Mass (length 910 mm) = 105 kg

Important: Due to high mass per metre, profiles greater than 12 kg/m will be supplied in Technical Grade only.

Forms of Corrosion

One of the principal reasons for choosing aluminium and its alloys for construction applications is their high corrosion resistance. Although aluminium is a chemically active metal, its behaviour is stabilised by the formation of a protective film of oxide on the surface. Generally, this film is stable in aqueous solutions with pH 4.5 – 8.5. Further considerations need to be made if the pH exceeds these limits or the environ-ment contains chloride.

Although generally very stable, the most common types of corrosion, which can occur on aluminium alloys, are summarised below:

Uniform attackThe corrosion proceeds homogeneously over the whole sur-face of the metal. With aluminium and its alloys this type of corrosion is mainly seen in very alkaline or acid environments where the solubility of the natural oxide film is high.

Pitting corrosionPitting corrosion is the most common type of corrosive pheno-mena with light alloys, and is characterised by local discon-tinuities in the oxide film, i.e. locally reduced film thickness, rupture, localised concentrations of impurities/alloying ele-ments, etc. Aluminium is sensitive to pitting when chloride ions are present (e.g. sea water). Pits develop at weak spots in the surface films and at sites where the oxide film is mechani-cally damaged.

Pitting can penetrate several millimetres during a short period of time if the surrounding conditions are extremely unfavour-able. The pits can be of different shapes, wide or narrow. The narrow pits can often be dangerous since the pits could be deep and difficult to detect.

The correct choice of alloy and surface treatment e.g. anodis-ing, powder coating, coating with anodic layer (Zn), cathodic protection with sacrificial anodes or applied current, or by use of inhibitors, are methods which can be used to limit or prevent pitting corrosion. Frequent cleaning, as well as ventila-tion of dense constructions and a profile design avoiding accumulation of stagnant water, are recommended.

Intergranular corrosion(IGC) is a selective corrosion around the grains and in the ad-jacent zones without any appreciable attack on the grain itself. The reason for the IGC is a difference in corrosion potential between grain boundaries and the bulk of the immediately adjacent grains. The difference in potential may be caused by the difference in chemical composition between the two zones. This situation may for example develop as a result of slow cooling after the extrusion process.

In this case the grains will be larger and the intermetallic par-ticles will precipitate on the grain boundaries, thus increasing the potential difference between the grain boundaries and the interior of the grain.

Due to the low metal consumption, intercrystalline corrosion is difficult to detect visually and even less by measurements of weight loss. However, if the corrosion is permitted to propa-gate into the metal, the mechanical properties of the material will be severely deteriorated.

Alloys in 6000 series are normally resistant to IGC, however, this is dependent on the chemical composition. Recrystall-ised structures in addition to high content of Si or Cu, may give corrosion of this type. Addition of Mn/Cr will prevent or minimise recrystallisation. IGC of alloys in 7000 series is linked to MgZn precipitates, which are very anodic compared to aluminium.

One action to prevent IGC is the correct choice of alloy. In ad-dition, see the actions mentioned under “Pitting Corrosion”.

Crevice corrosionCrevice corrosion may occur in narrow crevices, filled with liquid (e.g. water). Use of sealant prior to joining may prevent penetration of moisture. By use of correct profile design, it is possible to minimise the risk of crevice corrosion.

Water staining is a type of crevice corrosion and is caused by water or moisture entrapped between, for example, densely stacked profiles. Water staining is a very common corrosion type. The appearance varies from iridescent in mild cases, to white, grey or black in more severe instances. Water staining on profiles is normally removed by finishing (grinding) or pow-der coating.

Profiles without any surface treatment should never be stored outdoors, even though plastic wrapping is used, because of risk of condensation. Storing should be carried out in places with a maximum relative humidity of RH 45 %, and a maxi-

±mum temperature variation of 5°C. During transportation from a cold to a warmer area, the temperature should be increased gradually to avoid condensation on the metal.

Galvanic corrosionGalvanic corrosion is the type of corrosion that occurs when two metallic materials are in contact in the presence of an electrolyte. Corrosion will increase on the least noble material (the anode) and decrease on the noblest (the cathode). Since aluminium is less noble than most commonly used construc-tion materials, with the exception of zinc, magnesium and cadmium, this can be a serious form of corrosion with alumi-nium.

The protective effect from the oxide layer can be seriously compromised by the coupling to a more noble material. This is especially dangerous in atmospheres or water with high concentrations of chlorides or other aggressive substances.

Most types of aluminium corrosion can be related to some

Prev

Next

Pg 5


kind of galvanic coupling with a dissimilar material.Galvanic corrosion can be avoided or minimised by means of the following actions:

?If possible, avoid the use of materials far from each other in the galvanic potential difference series of the environ-ment where it will be used (stainless steel not included). However, if that is not a practical solution, the different material qualities have to be properly electrically insulated. It is important to use insulation material of proper electri-cal resistance and to avoid metallic contact in the entire construction. This can be checked by resistant measure-ments using a multimeter.

?Aluminium may be protected by means of sacrificial anodes. The most noble material can be surface treated with e.g. a metallic coating (Al/Zn), organic coating, (lacquer, paint, plastic, rubber) or a special coating for screws and bolts. The surface treatment has to be carried out correctly, that means treatment shall not be done only on the less noble material. As a consequence, a defect in the surface coating may generate a very unfavourable cathode/anode ratio (a big cathode area in relation to a small anode area gives considerable corrosion). Galvanic corrosion in, combination with crevice corrosion, may give concentrated attacks. Based on that, it is important to avoid entrapment of water or other liquids in crevices between materials of varying nobleness.

?Avoid transfer of ions of noble materials to aluminium sur-faces, for instance droplets from a copper tube on an alumi-nium surface will generate precipitation of copper metal. The result is corrosion of aluminium (deposition corrosion). The next step will be micro-galvanic corrosion between aluminium and the copper particles in the aluminium sur-face. Severe pitting may occur within a few weeks.

Filiform corrosion (FFC)Filiform corrosion on passivated surfaces exhibits itself as thin, threadlike and shallow attacks progressing below sur-face layers such as paint. The corrosion normally starts in coating defects (e.g. on mitres) and follows certain directions, like for example the extrusion direction. The front of the attack is supported by moisture, which penetrates the surface layer and becomes depleted of oxygen making the area anodic.

FFC is mainly an aesthetical problem, but corrosion products may cause deformation in narrow crevices or delamination of surface treatment. The extensive FFC attack observed during corrosion testing can be attributed to a reactive uppermost surface region showing an unpredictable chemical composi-tion, which may be formed during thermo-mechanical trans-formation of the alloy. It is proven that sufficient metal removal of aluminium 2 g/m² by chemical etching prior to properly performed chromating is required. Providing this is done properly, aluminium extrusions in 6060/6063 will exhibit high FFC resistance.

Corrosion resistance in different environments

The atmosphereCorrosion is insignificant in clean country air. Aluminium does not corrode where there are high levels of sulphur dioxide but can under certain circumstances become dark or matt in appearance.

WaterPitting can occur in stagnant water. The composition of the water is the important factor as the presence of copper, cal-cium, chloride and bicarbonate ions increase the risk signifi-cantly. This can be prevented however by regular cleaning and drying. In this way the aluminium is highly suitable for making saucepans for example.

SeawaterAlloys containing silicon, magnesium and manganese show good resistance to corrosion in seawater. Copper alloys on the other hand should be avoided.

SoilThe resistance to corrosion is to a great degree dependent on the moisture in the soil and its pH. Aluminium surfaces in contact with the soil are best treated with a thick layer of bitumen or a powder coating.

AcidsThe majority of inorganic acids have a very corrosive effect on aluminium – except nitric acid. High temperature, high acid concentrations and high levels of impurities in the level of the aluminium increase the rate of corrosion significantly.

AlkalisStrong alkalis are very corrosive. Sodium hydroxide reacts violently with aluminium. The rate of corrosion can be reduced in environments where the pH is between 9 and 11 by using silicates. Wet cement has a high pH and therefore corrodes aluminium alloys.

Organic compoundsAluminium is highly resistant to the majority of organic com-pounds. Corrosion can occur however with some anhydrous liquids.

Other materialIn practice the corrosion problem caused by the contact with other materials is for the most part small. The natural oxide layer provides protection.

Surface Treatment

In its natural state, Aluminium has a clean and attractive sur-face with good corrosion resistance. There are a number of types of surface treatments that improve resistance to corro-sion and mechanical wear. They can also provide a decorative appearance or in other ways alter the properties of the surface.

AnodisingAnodising is an electrochemical process where the thickness of the oxide film on the aluminium surface is increased artifi-cially. The process involves lowering the extrusion into an elec-trolytic bath where a DC current is connected to the extrusion, which acts as the anode in the circuit. While the natural oxide film is only 0.02 um, anodising increases the oxide layer to between 5 and 25 um depending on the product characteristics required. With the anodising process, aluminium's natural colour (naturally anodized) can be retained or a colour from a wide range of alternatives can be chosen.

Powder coatingPowder coating offers a virtually unlimited choice of colours and is very durable.

Other methods of surface treatmentOther methods of surface treatment include screen printing and the use of protective foils. Grinding, polishing and barrel processing are examples of mechanical surface treatments.

Prev

Next

Pg 5

Type 1

R1

A

A

TAnglesType 1 angles have legs of equal length and of equal thickness.The radii are all less than or equal to 0.80 mm. (C.C.D.: Circumscribing diameter)

15

15137 12.70 1.60 0.76 49 18 0.10215554 12.70 3.18 0.40 50 18 0.19115139 14.00 2.00 0.76 56 20 0.142150021 15.00 1.25 0.40 59 21 0.09715579 15.00 1.50 0.40 59 21 0.11515574 15.00 2.00 0.40 59 21 0.15115565 15.00 3.00 0.40 59 21 0.21915992 15.88 1.59 0.40 62 22 0.13015821 15.88 3.18 0.40 62 22 0.24615297 19.04 1.60 0.40 76 27 0.15615823 19.05 3.18 0.40 75 27 0.30115145 19.06 3.18 0.64 76 27 0.303150019 20.00 1.25 0.40 19 28 0.13115578 20.00 1.50 0.40 79 28 0.15615556 20.00 2.00 0.40 79 28 0.20615859 20.00 3.00 0.40 79 28 0.30015147 22.22 1.60 0.64 89 31 0.18515148 22.22 3.18 0.64 89 31 0.355150020 25.00 1.25 0.40 99 35 0.165150003 25.00 1.50 0.40 99 35 0.19715359 25.00 1.60 0.30 99 36 0.21015526 25.00 2.00 0.50 100 35 0.26015871 25.00 3.00 0.40 99 35 0.38215940 25.00 4.00 0.40 99 35 0.49815192 25.40 1.52 0.40 101 36 0.20315155 25.40 2.38 0.64 102 36 0.31115824 25.40 3.18 0.40 101 36 0.41015193 25.40 4.75 0.63 102 36 0.59215825 25.40 4.78 0.40 101 36 0.59615158 25.40 6.36 0.40 101 36 0.76615150 25.40 10.14 0.56 102 35 0.15415527 30.00 2.00 0.50 119 42 0.31415860 30.00 3.00 0.40 119 42 0.46315529 30.00 3.00 0.76 118 42 0.46215861 30.00 4.00 0.40 119 42 0.60715901 30.00 5.00 0.40 119 30 0.74515708 31.75 1.60 0.50 126 44 0.26815585 31.75 2.60 0.40 126 45 0.42915826 31.75 3.18 0.40 126 45 0.51915555 31.75 4.76 0.40 126 45 0.75715163 31.76 6.36 0.40 126 45 0.98515713 35.00 1.80 0.40 123 50 0.33315540 35.00 3.00 0.50 139 50 0.54415970 38.00 3.00 0.40 151 53 0.59315972 38.00 6.00 0.40 151 54 1.138150007 38.10 1.60 0.40 151 54 0.32315291 38.10 2.04 0.76 150 53 0.40915827 38.10 3.18 0.40 151 54 0.62915165 38.10 3.18 0.64 152 54 0.63015828 38.10 4.78 0.40 151 54 0.92515170 38.10 6.36 0.40 151 54 1.203150004 40.00 1.50 0.40 159 56 0.31915372 40.00 1.60 0.40 159 27 0.340

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm15862 40.00 2.00 0.40 159 56 0.42215879 40.00 3.00 0.40 159 56 0.62615557 40.00 4.00 0.40 159 56 0.82415532 40.00 5.00 0.76 158 57 1.01515373 40.00 6.00 0.40 159 57 1.203150014 44.45 4.76 0.40 177 63 1.08515172 44.46 3.18 0.40 177 63 0.73915913 45.00 4.00 0.40 179 64 0.93215890 45.00 5.00 0.40 179 64 1.15115563 50.00 2.00 0.40 199 50 0.53115736 50.00 2.00 0.80 198 76 0.53015733 50.00 3.00 0.50 200 71 0.78915530 50.00 3.00 0.76 198 71 0.78715906 50.00 4.00 0.40 199 71 1.04015854 50.00 6.00 0.40 199 70 1.52815908 50.00 8.00 0.40 199 71 1.99415993 50.80 1.59 0.40 202 72 0.43115829 50.80 3.18 0.40 202 72 0.84815830 50.80 4.78 0.40 202 72 1.25415831 50.80 6.35 0.40 202 72 1.63915174 50.80 9.52 0.76 201 72 2.374150000 60.00 2.00 0.40 239 85 0.63915575 60.00 2.50 0.40 239 85 0.79615880 60.00 3.00 0.40 239 85 0.95115572 60.00 4.00 0.40 239 85 1.25715881 60.00 5.00 0.40 239 85 1.55815872 60.00 6.00 0.40 239 85 1.85315506 60.00 8.00 0.50 239 85 2.43015207 63.50 3.18 0.64 252 89 1.06615176 63.50 6.36 0.40 254 90 2.08015363 64.00 8.00 0.76 254 91 2.60015939 70.00 5.00 0.40 279 99 1.82915907 70.00 6.00 0.40 279 99 2.17815485 75.00 3.00 0.50 299 106 1.19415980 75.00 6.00 0.40 299 106 2.34015735 76.00 2.00 0.50 304 107 0.81315420 76.00 4.00 0.64 304 107 1.60415832 76.20 3.18 0.40 304 108 1.28615833 76.20 4.78 0.40 304 108 1.91215834 76.20 6.35 0.40 304 108 2.51315209 76.20 6.35 0.64 305 108 2.51415210 76.20 9.52 0.64 303 107 3.68515178 76.20 12.70 0.76 303 108 4.81715995 88.90 6.35 0.40 355 125 2.95015922 100.00 3.00 0.40 399 141 1.60115905 100.00 10.00 0.40 399 141 5.14915984 101.60 6.35 0.40 405 153 3.38715994 101.60 9.53 0.40 405 143 5.00115181 101.60 12.70 0.78 404 143 6.55515947 120.00 8.00 0.40 479 170 5.02915856 120.00 12.00 0.40 479 170 7.414150005 152.40 12.70 0.40 608 215 10.05

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm


Prev

Next

Pg 5

Type 2 AnglesType 2 angles have legs of equal length and of equal thickness. The radii are all greater than 0.80 mm.

16

Type 3 Type 3 angles have legs of equal length and of equal thickness. The inside corner radius is greater than 0.80 mm.Other radii are less than or equal to 0.80 mm.

R1

R2

A

A

T

R1

R2

A

A

T

15810 44.45 6.35 4.76 3.18 172 63 1.42115349 50.00 3.00 3.00 1.50 196 69 0.78915990 50.00 4.70 1.00 1.00 198 70 1.21315949 50.00 5.00 1.20 1.20 198 71 1.26015545 50.80 3.18 6.35 3.18 197 72 0.86015546 50.80 4.76 6.35 3.18 197 72 1.26015547 50.80 6.35 6.35 3.18 197 72 1.65015811 63.50 6.35 6.35 3.18 248 90 2.08715543 76.20 6.35 7.93 6.35 295 108 2.50315964 76.20 6.35 7.95 3.18 298 109 2.53915544 76.20 9.53 7.93 6.35 295 108 3.67915135 101.60 6.36 9.52 6.36 396 144 3.39715813 101.60 9.53 9.53 6.35 396 144 5.00715851 101.60 12.70 9.54 6.35 396 144 6.562

R2

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

15096 25.40 3.18 4.58 0.64 100 36 0.42215966 38.10 3.18 2.38 0.38 149 54 0.62615102 38.10 3.18 5.34 0.64 150 54 0.64615103 38.10 4.74 5.34 0.64 150 54 0.93815104 38.10 6.36 5.34 0.64 150 54 1.22015110 50.80 3.18 6.10 0.64 201 72 0.87015111 50.80 4.74 6.10 0.64 201 72 1.26915112 50.80 6.36 6.10 0.64 199 72 1.66215113 50.80 7.92 6.10 0.64 201 72 2.03515118 63.50 6.36 6.86 0.64 251 90 2.10315119 63.50 7.92 6.86 0.64 251 90 2.62015121 76.20 6.36 7.62 0.64 300 107 2.55015122 76.20 7.96 7.62 0.64 300 108 3.14815123 76.20 9.52 7.62 0.64 300 107 3.71915125 88.90 6.36 8.38 0.64 352 126 2.99415234 88.90 7.95 8.38 0.64 351 126 3.69915127 88.90 9.52 8.38 0.64 351 125 4.38115128 88.90 12.70 8.38 0.64 351 126 5.72215479 100.00 4.00 4.50 0.50 397 141 2.13615130 101.60 9.52 9.14 0.64 402 144 5.05215132 127.00 9.52 10.66 0.76 503 180 6.38215294 127.00 12.70 6.36 0.76 504 197 8.32715286 152.40 9.52 12.18 0.76 603 216 7.70315287 152.40 12.70 12.18 0.76 603 216 10.138

R2

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm


Prev

Next

Pg 5

Type 4 AnglesType 4 angles have legs of unequal length but of equal thickness. The radii are all less than or equal to 0.80 mm.

17

15561 15.00 10.00 2.00 0.40 49 18 0.12415408 15.88 9.52 1.60 0.64 49 19 0.10215000 19.04 6.36 1.60 0.76 50 20 0.10315441 19.06 9.54 2.38 0.76 57 21 0.16915038 19.06 12.70 1.58 0.76 62 23 0.12815039 19.06 12.70 3.18 0.64 64 23 0.24715322 20.00 9.00 3.00 0.50 58 24 0.21115909 20.00 10.00 2.00 0.40 59 22 0.15115885 20.00 15.00 2.00 0.40 69 25 0.17915040 20.66 6.36 1.60 0.76 52 22 0.10915376 22.00 8.00 3.00 0.30 59 24 0.21915041 22.22 7.96 3.18 0.78 60 23 0.23215042 22.22 9.52 1.60 0.76 62 24 0.12915043 22.22 9.52 3.18 0.76 62 24 0.245

150027 25.00 10.30 1.30 0.50 69 27 0.11915347 25.00 12.00 1.50 0.30 74 28 0.14615928 25.00 15.00 2.00 0.40 79 29 0.206

150001 25.00 20.00 1.60 0.40 89 32 0.18815985 25.00 20.00 3.00 0.40 89 32 0.34115241 25.40 12.70 1.60 0.64 75 28 0.15715050 25.40 12.70 3.18 0.20 76 28 0.30115051 25.40 15.88 1.60 0.64 83 30 0.17115264 25.40 15.88 3.18 0.64 83 30 0.32915836 25.40 19.05 3.18 0.40 88 32 0.35515412 28.00 22.00 2.48 0.76 98 36 0.31815731 30.00 10.00 2.00 0.25 79 31 0.20615567 30.00 15.00 2.00 0.40 89 33 0.23315558 30.00 15.00 3.00 0.40 89 34 0.34115875 30.00 20.00 2.00 0.40 99 36 0.25915559 30.00 20.00 3.00 0.40 99 36 0.38215926 30.00 20.00 4.00 0.40 99 36 0.49815255 31.76 12.70 2.64 0.64 89 34 0.29515411 31.76 15.88 2.76 0.76 93 36 0.33315057 31.76 19.06 3.18 0.40 102 37 0.41015463 31.76 25.40 2.00 0.76 114 41 0.29815058 31.76 25.40 3.18 0.40 113 40 0.46515059 32.94 17.86 1.60 0.64 102 33 0.21315882 35.00 20.00 3.00 0.40 109 41 0.42215061 38.10 12.70 3.18 0.64 102 40 0.40915837 38.10 19.05 3.18 0.40 113 43 0.46515838 38.10 25.40 3.18 0.40 126 46 0.51915845 38.10 25.40 4.75 0.50 126 46 0.51915581 40.00 10.00 2.00 0.40 99 41 0.258

150002 40.00 20.00 1.60 0.40 119 44 0.25315876 40.00 20.00 2.00 0.40 119 44 0.31415891 40.00 20.00 2.50 0.40 119 45 0.38915886 40.00 20.00 3.00 0.40 119 44 0.46315576 40.00 20.00 4.00 0.40 119 45 0.60715950 40.00 25.00 2.00 0.40 129 47 0.34115986 40.00 25.00 3.00 0.40 129 47 0.50415931 40.00 30.00 2.00 0.40 139 50 0.36815562 40.00 30.00 3.00 0.40 139 50 0.54415258 44.45 19.05 3.17 0.63 126 48 0.520

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T

mm

R1

mm

R1

A

B

T


Prev

Next

Pg 5

Type 4continued

AnglesType 4 angles have legs of unequal length but of equal thickness. The radii are all less than or equal to 0.80 mm.

18

15064 44.46 22.22 2.04 0.64 132 50 0.35615065 44.46 22.22 3.18 0.64 133 50 0.54815067 44.46 38.10 3.18 0.76 165 59 0.68415892 45.00 20.00 3.00 0.40 129 49 0.50415339 46.00 17.00 2.00 0.50 125 49 0.33015308 46.00 34.00 3.00 0.76 158 57 0.62515523 48.00 25.00 2.00 0.50 146 54 0.38515954 50.00 15.00 2.00 0.40 129 52 0.34115893 50.00 15.00 2.50 0.40 129 52 0.42315877 50.00 20.00 2.00 0.40 139 54 0.36815937 50.00 20.00 3.00 0.40 139 54 0.544

150012 50.00 25.00 1.60 0.40 149 56 0.31815987 50.00 25.00 3.00 0.40 149 56 0.58515956 50.00 25.00 4.00 0.40 149 56 0.76915571 50.00 30.00 2.00 0.40 159 58 0.42215932 50.00 30.00 3.00 0.40 159 58 0.62615933 50.00 30.00 4.00 0.40 159 58 0.82415564 50.00 40.00 3.00 0.40 179 64 0.70715248 50.80 25.40 1.60 0.64 151 56 0.32215073 50.80 25.40 2.02 0.76 152 57 0.40915075 50.80 25.40 6.36 0.76 152 57 1.20415976 50.80 12.70 3.18 0.50 126 52 0.51915839 50.80 19.05 3.18 0.40 139 54 0.57415840 50.80 25.40 3.18 0.40 151 57 0.62915849 50.80 25.40 4.76 0.40 151 57 0.92115841 50.80 38.10 3.18 0.40 177 64 0.73815902 50.80 38.10 4.76 0.40 177 63 1.08615894 55.00 15.00 2.00 0.40 139 57 0.36815927 60.00 15.00 2.00 0.40 149 62 0.39515582 60.00 25.00 2.00 0.40 169 65 0.44915923 60.00 25.00 2.50 0.40 169 65 0.55915857 60.00 30.00 3.00 0.40 179 66 0.70715953 60.00 30.00 4.00 0.40 179 67 0.93215924 60.00 40.00 3.00 0.40 199 72 0.78815929 60.00 40.00 4.00 0.40 199 72 1.04015888 60.00 40.00 5.00 0.40 200 72 1.28715959 60.00 40.00 6.00 0.40 199 72 1.52815361 60.00 41.50 2.50 0.50 202 73 0.67015899 60.00 50.00 2.00 0.40 219 78 0.58515570 60.00 50.00 4.00 0.50 219 79 1.14815078 63.50 25.40 3.18 0.64 178 68 0.738

150010 63.50 38.10 3.18 0.40 202 74 0.84815903 63.50 38.10 4.76 0.40 202 74 1.24915989 63.50 38.10 6.35 0.40 202 74 1.63915262 63.50 50.80 6.36 0.64 229 81 1.86015375 70.00 50.00 1.50 3.00 239 86 0.482

150025 70.00 60.00 2.00 0.60 258 92 0.69315374 70.50 53.00 6.00 0.50 246 88 1.91015522 71.00 25.00 2.00 0.50 192 75 0.50915348 75.00 20.00 5.00 0.30 189 78 1.21915520 75.00 25.00 2.00 0.50 200 79 0.53115999 75.00 50.00 3.00 0.40 249 90 0.99115517 75.00 50.00 4.00 0.76 250 90 1.312

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T

mm

R1

mm

R1

A

B

T


Prev

Next

Pg 5

AnglesType 4 angles have legs of unequal length but of equal thickness. The radii are all less than or equal to 0.80 mm.

Type 4continued

19

R1

A

B

T

15969 75.00 50.00 6.00 0.40 249 90 1.93515569 76.00 22.00 1.50 0.40 195 79 0.39215504 76.00 22.00 2.00 0.40 196 79 0.52015355 76.00 38.00 2.00 0.50 227 85 0.60615083 76.20 19.44 1.78 0.76 195 79 0.46215421 76.20 25.40 2.03 0.76 203 80 0.54815842 76.20 25.40 3.18 0.40 203 80 0.84815085 76.20 38.10 3.18 0.40 228 85 0.95715252 76.20 38.10 4.74 0.64 229 85 1.41015988 76.20 38.10 6.35 0.40 228 85 1.85715843 76.20 50.80 3.18 0.40 253 92 1.067

150015 76.20 50.80 4.50 0.40 253 91 1.49315263 76.20 50.80 6.35 0.64 252 91 2.07515086 76.20 63.50 7.96 0.76 277 99 2.84015936 80.00 20.00 2.00 0.40 199 82 0.53115942 80.00 25.00 2.50 0.40 209 84 0.69415925 80.00 30.00 3.00 0.40 219 85 0.86915920 80.00 40.00 3.00 0.40 239 89 0.95115870 80.00 40.00 4.00 0.40 239 89 1.25715863 80.00 40.00 5.00 0.40 239 89 1.55815455 84.50 28.00 1.40 0.76 224 89 0.45615850 88.90 31.75 3.18 0.40 240 94 1.01215087 88.90 63.50 9.52 0.78 305 109 3.69115356 100.00 35.00 3.00 0.50 269 105 1.07215919 100.00 40.00 3.00 0.40 279 108 1.11315934 100.00 40.00 4.00 0.40 279 108 1.47415878 100.00 50.00 3.00 0.40 299 112 1.19515518 100.00 50.00 4.00 0.76 300 112 1.58015858 100.00 50.00 5.00 0.40 299 112 1.96415887 100.00 50.00 6.00 0.40 299 112 2.34115900 100.00 70.00 2.00 0.40 339 122 0.91015844 101.60 50.80 3.18 0.40 304 114 1.28615977 101.60 50.80 6.35 0.50 304 113 2.513

150008 101.60 76.20 6.35 0.40 355 127 2.95015524 110.00 25.00 2.00 0.50 270 113 0.72115364 110.00 90.00 8.00 0.30 399 142 4.16215519 115.00 25.00 2.00 0.50 280 118 0.74815962 120.00 60.00 8.00 0.40 359 134 3.72815944 120.00 80.00 3.00 0.40 399 144 1.60115943 120.00 100.00 4.00 0.40 439 156 2.34115290 127.00 50.80 2.00 0.76 354 137 0.95115971 130.00 100.00 8.00 0.50 459 164 4.81215952 150.00 50.00 4.00 0.40 399 158 2.124

150017 150.00 50.00 6.00 0.50 399 158 3.15415958 150.00 100.00 10.00 0.40 499 180 6.504

150006 152.40 76.20 6.35 0.40 456 170 3.82415983 152.40 76.20 9.53 0.40 456 170 5.657

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T

mm

R1

mm


Prev

Next

Pg 5

Type 5

Type 6

Angles

Angles

Type 5 angles have legs of unequal length but of equal thickness. The outside corner radii are all greater than 0.80 mm.

Type 6 angles have legs of unequal length but of equal thickness. The inside corner radius is greater than 0.80 mm.Other radii are less than or equal to 0.80 mm

20

R1

A

B

T

R1

A

B

T

R2

15002 38.10 25.40 3.18 5.08 0.64 125 46 0.53515214 50.80 25.40 3.18 5.33 0.64 150 57 0.64615272 50.80 38.10 6.34 6.34 0.76 175 64 1.44515216 63.50 38.10 3.18 6.10 0.64 201 74 0.86515011 63.50 50.80 0.52 7.96 0.76 226 81 2.74415010 63.50 50.80 3.18 6.60 0.64 226 81 0.98315012 63.50 50.80 6.36 6.60 0.64 226 81 1.92115013 76.20 25.40 6.36 7.92 0.64 198 81 1.67715018 76.20 38.10 9.52 6.36 0.64 229 85 2.73015016 76.20 50.80 6.36 6.86 0.64 251 92 2.10515017 76.20 50.80 7.96 6.36 0.64 229 85 2.59015225 88.90 63.50 9.52 7.62 0.64 300 109 3.71815228 88.90 76.20 12.70 8.13 0.64 327 117 5.28215271 101.60 50.80 9.52 8.12 0.76 301 114 3.72515024 101.60 63.50 6.36 8.12 0.64 327 120 2.77415025 101.60 76.20 9.52 8.38 0.64 352 127 4.38915027 127.00 76.20 9.52 9.14 0.64 401 148 5.04415327 140.00 50.00 3.00 3.00 0.50 377 149 1.50715991 140.00 100.00 6.00 5.00 0.40 477 172 5.34715350 150.00 45.00 5.00 5.00 0.50 387 157 2.58815028 152.40 76.20 9.52 9.90 0.64 452 170 5.70815231 152.40 76.20 12.70 9.90 0.64 452 170 7.48715457 152.40 88.90 9.52 10.42 0.76 487 176 6.037

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.

C.C.D.

mm

Profile

Number

A

mm

B

mm

T

mm

15341 22.00 16.00 3.00 0.50 1.00 74 27 0.28115846 63.50 38.10 6.35 6.35 3.18 197 74 1.65015852 63.50 50.80 4.76 6.35 3.18 222 81 1.42415515 65.00 35.00 10.00 1.00 1.00 200 74 2.43715816 76.20 50.80 6.36 7.94 4.76 246 92 2.08915333 100.00 75.00 5.00 2.00 2.50 346 125 2.29815847 101.60 76.20 6.35 9.53 6.35 345 127 2.95715963 114.30 76.20 6.35 8.80 6.10 372 137 3.17115819 127.00 76.20 9.53 9.53 7.94 395 148 4.98115474 140.00 63.50 6.35 9.53 4.76 400 154 3.432

Profile

Number

A

mm

B

mm

T

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.

C.C.D.

mm


Prev

Next

Pg 5

Type 13 AnglesType 13 angles have legs of unequal length but of equal thickness.

21

R1

R1

A

B

T

R2

15433 21.12 15.88 2.04 3.04 0.76 5.08 69 26 0.18215295 25.40 25.40 2.38 0.76 2.39 1.19 99 35 0.30115323 54.00 25.00 3.00 5.00 0.50 8.00 152 60 0.59415996 190.50 76.20 12.70 12.20 1.00 1.00 526 205 8.83

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

R3

mm

Anod.

Peri.

Profile

Number

A

mm

B

mm

T

mm


Prev

Next

Pg 5

Type 1 ChannelsType 1 channels are of a uniform thickness with all radii less than or equal to 1.00 mm.

22

16007 9.52 9.52 1.60 0.76 54 13 0.11016008 9.52 12.70 1.60 0.76 67 16 0.13816502 9.52 19.06 1.58 0.25 92 21 0.19016009 10.00 10.00 1.50 0.26 54 14 0.11016895 10.00 10.00 2.00 0.40 55 14 0.14116500 11.00 10.00 1.50 0.50 59 15 0.11416472 12.00 10.00 1.50 0.40 60 16 0.11716016 12.70 9.52 1.52 0.76 51 16 0.11716445 12.70 12.70 1.50 0.50 73 18 0.14316018 12.70 12.70 2.04 0.76 72 18 0.18716020 12.70 12.70 3.18 0.76 70 18 0.27316824 12.70 19.05 3.18 0.40 94 23 0.38316022 14.30 7.96 1.60 0.64 57 16 0.11516473 15.00 10.00 1.50 0.40 66 18 0.13016465 15.00 15.00 1.50 0.40 86 21 0.17016885 15.00 15.00 2.00 0.40 85 21 0.22216026 15.87 12.70 1.63 0.82 79 20 0.16816027 15.88 15.88 1.60 0.40 91 22 0.192

160042 15.88 15.88 3.18 0.40 88 22 0.35516444 16.00 48.50 3.00 0.50 230 53 0.918

160037 17.00 20.00 1.45 0.40 110 26 0.21216470 18.00 20.00 1.45 0.40 110 26 0.212

160026 18.70 38.00 1.85 0.50 183 41 0.45016348 19.00 20.00 1.50 0.50 115 28 0.23016223 19.05 19.05 3.18 0.50 108 27 0.43716031 19.06 12.70 1.60 0.76 83 23 0.17816032 19.06 12.70 3.18 0.64 83 23 0.32716464 20.00 10.00 2.00 0.40 75 22 0.19516341 20.00 15.00 2.00 0.50 96 25 0.24916466 20.00 20.00 1.50 0.40 116 28 0.23116867 20.00 20.00 2.00 0.40 115 28 0.30316887 20.00 30.00 2.00 0.40 155 36 0.41216396 21.00 18.60 1.20 0.30 122 30 0.19616902 21.00 25.00 2.50 0.50 135 33 0.44616857 21.20 30.00 2.00 0.50 157 36 0.41816907 21.80 21.80 6.00 0.50 117 31 0.868

160027 22.22 22.22 3.17 0.50 125 31 0.51816710 22.23 22.23 1.63 0.50 130 31 0.28016357 22.61 69.85 1.78 0.50 320 73 0.76616430 23.00 6.00 2.00 0.50 64 24 0.16716919 23.00 25.00 2.00 0.50 140 34 0.37316220 23.17 23.17 1.27 0.38 138 33 0.23216041 23.24 22.98 1.40 0.76 133 31 0.25116417 23.82 35.00 1.60 0.64 182 42 0.39216043 23.82 50.80 1.60 0.78 245 55 0.52816421 24.00 38.00 3.00 0.50 194 45 0.76416923 25.00 12.00 1.50 0.50 93 14 0.18616395 25.00 20.00 1.50 0.30 126 32 0.25116428 25.00 20.00 3.50 0.20 123 32 0.55016446 25.00 25.00 2.00 0.40 145 36 0.38416448 25.00 25.00 3.00 0.40 143 35 0.56116505 25.40 12.70 1.58 0.50 98 28 0.20216825 25.40 12.70 3.18 0.40 94 29 0.383

R1

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

AT1

T1

B

R1


Prev

Next

Pg 5

ChannelsType 1 channels are of a uniform thickness with all radii less than or equal to 1.00 mm.

Type 1continued

23

16048 25.40 15.88 1.60 0.64 111 30 0.23416826 25.40 19.05 3.18 0.40 119 32 0.49216827 25.40 25.40 3.18 0.40 145 36 0.60116828 25.40 50.80 3.18 0.40 246 57 1.039

160036 25.40 63.50 3.18 0.40 221 68 0.93016881 25.70 23.60 1.60 0.50 141 35 0.302

160002 27.00 20.00 3.00 0.50 127 33 0.49616339 29.00 12.70 1.20 0.50 106 32 0.16916530 29.00 65.00 3.00 0.50 312 70 1.47916254 29.46 30.15 3.18 0.64 173 42 0.71916056 29.84 15.88 3.18 0.76 117 34 0.45016889 30.00 20.00 2.00 0.40 135 36 0.35716927 30.00 23.00 2.00 0.50 186 56 0.49816449 30.00 30.00 3.00 0.40 173 42 0.68316830 31.75 31.75 3.18 0.40 183 45 0.76616059 31.76 12.70 3.18 0.64 108 34 0.43816061 31.76 25.40 2.64 0.76 160 41 0.55316072 31.76 63.50 1.90 0.76 318 71 0.82116384 32.00 12.00 1.50 0.50 107 34 0.21416066 32.14 25.40 3.18 0.64 160 41 0.66016067 32.20 19.04 1.56 0.64 137 37 0.28916389 33.25 38.00 1.50 0.50 214 50 0.43116476 33.50 35.00 2.00 0.50 209 51 0.56016255 34.93 12.83 1.52 0.76 116 38 0.236

160014 35.20 100.00 2.00 0.50 465 106 1.25316069 35.36 9.52 1.58 0.64 106 37 0.22016354 36.00 27.40 2.00 0.50 178 42 0.47016372 38.00 25.00 2.00 0.20 171 45 0.45516408 38.00 50.00 6.00 0.25 264 63 2.04916832 38.10 19.05 3.18 0.40 145 43 0.60116833 38.10 25.40 3.18 0.40 170 46 0.71116077 38.10 25.40 6.36 0.64 159 46 1.31216079 38.10 28.58 3.18 0.64 184 48 0.76716834 38.10 38.10 3.18 0.40 221 54 0.930

160035 38.10 38.10 6.35 0.40 215 54 1.74816426 39.20 32.00 1.70 0.76 200 51 0.45816450 40.00 20.00 2.00 0.40 155 45 0.41216463 40.00 29.00 3.00 0.50 200 49 0.79616890 40.00 40.00 3.00 0.40 233 56 0.92616886 40.00 40.00 4.00 0.40 231 56 1.21416383 42.00 25.00 2.00 0.50 178 49 0.47616462 43.00 50.00 2.00 0.50 280 66 0.75216567 43.76 19.06 1.50 0.75 160 48 0.32016917 44.00 12.00 1.50 0.50 132 45 0.262

160043 44.00 17.00 2.00 0.30 151 47 0.40116092 44.02 28.58 1.78 0.76 199 52 0.471

160044 44.10 19.00 1.57 0.79 159 48 0.33416268 44.44 15.88 1.62 0.76 146 47 0.31716094 44.46 25.40 3.18 0.76 182 51 0.76516924 45.50 22.00 2.50 0.50 172 51 0.57216912 47.00 47.00 3.00 0.50 230 32 0.91816360 47.30 19.00 1.40 0.71 167 51 0.31416100 47.50 19.06 1.52 0.76 165 51 0.341

R1

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

AT1

T1

B

R1


Prev

Next

Pg 5

Type 1continued


24

16729 47.65 44.45 1.60 0.50 263 65 0.57916332 48.51 12.70 1.60 0.80 145 50 0.30516423 48.90 19.06 1.80 0.50 168 52 0.40616106 48.90 19.06 2.04 0.76 167 52 0.456

160052 49.40 54.85 3.00 0.50 310 73 1.24416811 50.00 20.00 1.25 0.63 178 54 0.29616588 50.00 25.00 1.50 0.50 195 56 0.39416451 50.00 30.00 3.00 0.40 213 58 0.845

160034 50.00 50.00 3.00 0.40 293 70 1.170160003 50.00 50.00 4.00 0.40 291 70 1.53916110 50.80 14.48 1.78 0.76 153 53 0.36616836 50.80 25.40 3.18 0.40 195 57 0.82016882 50.80 25.40 4.76 0.40 192 57 1.18816872 50.80 25.40 6.35 0.40 189 57 1.529

160029 50.80 38.10 6.35 0.40 240 63 1.96716856 50.80 50.80 3.18 0.40 297 72 1.25816837 50.80 50.80 6.35 0.40 291 72 2.40416369 51.60 25.90 1.80 0.50 203 74 0.48616892 55.00 45.00 2.00 0.40 285 71 0.76416869 55.00 50.00 2.00 0.40 305 74 0.81816118 58.82 25.40 3.30 0.76 209 64 0.88916119 59.54 21.60 3.30 0.76 196 63 0.86316452 60.00 20.00 2.00 0.40 195 63 0.52016870 60.00 40.00 3.00 0.40 273 72 1.08916398 60.00 40.00 4.00 0.30 271 73 1.43016874 60.00 40.00 5.00 0.40 269 72 1.76116457 60.00 50.00 3.00 0.40 313 78 1.25216458 60.00 60.00 3.00 0.40 353 85 1.41416841 63.50 38.10 3.18 0.40 272 74 1.149

160028 63.50 50.80 3.17 0.50 322 81 1.36316453 65.00 25.00 2.50 0.40 224 69 0.74516447 70.00 35.00 3.00 0.40 273 78 1.08916406 70.50 17.00 2.00 0.50 204 73 0.544

160045 71.00 40.00 4.00 0.50 292 81 1.549160024 75.00 50.00 6.00 0.40 337 90 2.64916434 76.00 20.00 1.50 0.50 227 79 0.45916281 76.20 14.30 1.60 0.64 203 78 0.44116125 76.20 19.06 3.18 0.76 220 79 0.92716322 76.20 25.40 2.50 0.76 246 80 0.82616248 76.20 25.40 3.18 0.64 248 80 1.03716126 76.20 38.10 3.18 0.64 298 85 1.258

160030 76.20 38.10 4.76 0.40 294 85 1.843160039 76.20 38.10 6.36 0.40 291 85 2.40716127 76.20 44.46 3.18 0.64 324 88 1.367

160038 76.20 50.80 3.18 0.40 348 91 1.47716880 76.20 50.80 6.35 0.40 342 91 2.84116587 80.00 35.00 2.00 0.50 296 87 0.79116879 86.00 40.00 3.00 0.40 325 95 1.30016875 88.00 50.00 3.00 0.40 369 101 1.47916597 90.00 20.00 3.00 0.50 252 92 1.00816420 95.00 32.00 6.00 0.75 305 100 0.39016343 97.25 19.00 1.50 0.50 268 99 0.53716876 100.00 40.00 3.00 0.40 353 108 1.414

R1

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

AT1

T1

B

R1


Prev

Next

Pg 5


Type 1continued

25

Type 2

Type 2 channels have the web and flanges of different thicknesses and all radii less than or equal to 0.80 mm.

AT1

T1

B

R1

AT2

T1

B

R1

16877 100.00 50.00 5.00 0.40 389 112 2.57416802 101.60 44.45 3.17 0.78 372 110 1.58116133 101.60 50.80 3.18 0.78 397 113 1.695

160032 101.60 50.80 6.00 0.40 393 113 3.108160051 101.60 50.80 8.00 0.60 388 113 3.63516302 102.40 15.88 2.00 0.76 266 108 0.72816801 102.40 44.45 3.17 0.78 388 117 1.64416911 104.00 42.00 2.00 0.50 370 112 0.997

160006 105.00 38.00 2.00 0.50 356 111 0.95916878 106.00 40.00 3.00 0.40 365 113 1.46316135 111.24 38.10 4.56 0.76 363 118 2.20816865 120.00 45.00 10.00 0.40 399 128 5.14916570 125.00 45.00 3.18 0.80 421 132 1.797

160041 127.00 34.93 9.53 0.75 372 131 4.59116140 139.70 18.26 2.38 0.64 341 141 1.09716863 140.00 60.00 8.00 0.40 503 152 5.289

160040 152.40 76.20 4.76 0.40 599 170 3.80916556 158.75 50.80 3.18 0.80 512 166 2.190

160016 175.00 45.00 2.25 sharp 526 180 1.58816868 180.00 64.00 4.00 0.40 607 191 3.25216563 210.00 30.00 3.00 0.76 531 212 2.147

R1

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

16806 8.50 22.00 2.00 1.50 0.75 99 24 0.20716148 15.88 23.02 8.74 3.96 0.64 106 28 0.68216150 25.40 22.22 3.18 1.60 0.64 133 34 0.38516460 40.00 20.20 8.00 8.00 0.50 143 44 1.395

160033 88.90 38.10 6.36 7.93 0.50 316 96 2.896

Est.

kg/m

T2

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

Profile

Number

A

mm

B

mm

T1

mm


Prev

Next

Pg 5

Type 3 ChannelsType 3 channels may have the web and flanges of different thicknesses. The two inside corner radii are always greater than 0.80 mm.All other radii are less than or equal to 0.80 mm.

26

Type 4

Type 4 channels may have the web and flanges of different thicknesses. The radii on both the inside corners of the channel and the inside cornersof the legs are greater than 0.80 mm.

AT2

T1

B

R1

R2

AT2

T1

B

R1

R2

R3

16303 16.36 15.68 1.60 1.60 3.00 0.76 88 23 0.202160019 47.63 34.93 3.18 3.18 3.18 0.50 225 59 0.96916443 50.80 25.40 3.30 3.30 2.54 0.60 193 56 0.85616197 50.80 31.75 6.35 6.35 3.18 0.64 216 60 1.76016178 63.50 26.18 3.18 3.18 1.58 0.67 224 69 0.93616386 64.00 35.00 2.00 2.00 1.00 0.50 262 72 0.704

160013 72.22 35.00 3.18 3.18 3.18 0.64 274 80 1.18116184 88.90 53.98 6.36 6.36 6.36 0.64 375 104 3.21516185 94.60 22.45 1.75 1.75 1.60 0.63 271 96 0.65316525 101.60 50.80 3.96 4.74 14.28 0.64 386 114 2.536

160022 101.60 50.80 6.35 7.94 9.15 0.50 385 114 3.75916293 104.02 48.00 8.00 11.43 1.58 0.76 384 115 4.86516236 127.00 50.80 6.36 7.96 9.14 0.64 437 137 4.20016158 127.00 63.50 6.36 9.52 10.66 0.64 484 142 5.26816266 130.00 60.00 4.00 6.00 6.00 0.76 492 143 3.27016566 150.00 35.00 10.00 25.00 11.10 0.80 410 154 7.59416235 152.40 50.80 6.36 7.96 9.14 0.64 487 161 4.63716159 152.40 63.50 6.36 7.92 10.66 0.64 537 165 5.21516289 152.40 76.20 6.36 9.52 12.18 0.64 585 170 6.40116524 152.40 76.20 9.52 12.70 12.20 0.62 578 170 8.69416539 177.80 50.80 6.36 9.52 9.14 0.76 551 184 5.45516000 177.80 76.20 6.34 11.12 12.20 0.62 636 193 7.43716234 177.80 88.90 7.92 12.70 13.72 0.64 683 199 9.62016598 203.00 89.00 9.52 14.28 14.28 0.64 728 222 11.77416541 203.20 65.02 11.84 11.84 12.70 0.80 630 213 10.10016001 203.20 76.20 7.14 11.10 7.14 0.62 689 217 8.144

160023 203.20 76.20 9.52 12.70 12.20 0.64 680 217 10.000

Profile

Number

A

mm

B

mm

T1

mm

C.C.D.

mm

Est.

kg/m

T2

mm

R1

mm

R2

mm

Anod.

Peri.


16475 8.00 16.00 1.20 1.20 0.20 0.60 0.50 76 17 0.12116459 14.00 35.00 1.30 1.30 0.20 1.80 0.20 164 38 0.28416518 29.46 25.40 2.04 2.04 3.18 2.06 1.02 156 39 0.40916442 38.30 30.00 1.40 1.40 2.40 1.00 0.50 191 49 0.35716256 43.24 7.92 3.18 2.38 1.20 0.64 0.64 109 44 0.43016461 49.00 40.00 2.00 2.00 0.50 1.00 0.50 251 63 0.67516817 51.00 50.00 3.00 3.00 5.00 2.00 0.50 289 71 1.15416412 52.20 13.00 1.20 1.20 4.20 3.00 0.25 153 56 0.24516435 60.00 18.00 4.00 8.00 2.00 4.00 0.50 177 63 1.26616522 76.20 50.80 0.34 6.34 12.70 6.34 0.76 325 92 2.70216583 150.00 100.00 10.00 10.00 15.00 7.50 1.00 659 180 8.74416267 200.02 88.90 11.12 11.12 13.72 13.72 0.76 709 219 10.742

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

T2

mm

R1

mm

R2

mm

R3

mm

Profile

Number

A

mm

B

mm

T1

mm

Prev

Next

Pg 5

229 25.40 15.88 12.70 1.60 1.60 1.60 0.79 2.39 0.8 104 30 0.22112 82.56 31.76 47.62 3.18 3.18 3.18 2.38 2.38 0.64 281 88 1.21111 88.90 44.46 38.12 3.18 3.18 6.36 2.38 3.18 - 331 99 1.74876 139.70 38.10 22.22 3.18 3.18 3.18 3.18 3.18 0.64 409 145 1.733

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

C

mm

T1

mm

B

mm

T2

mm

T3

mm

R1

mm

R2

mm

R3

mm

Est.

kg/m

27

Type 5 ChannelsType 5 channels may have the web and flanges of different thicknesses. The radii on both the inside and outside corners of the channel are greater than 0.80 mm.The radii of the legs are less than or equal to 0.80 mm.

Type 11

Type 11 channels are sometimes referred to as “C” sections.The web, flanges and feet may all differ in thickness. They usually have a radius onthe inside of the angle formed between the web and flange and the flange and the feet.Other radii are less than or equal to 0.80 mm.

Type 15

Type 15 channels have tapered legs of equal length and thickness. The inside corner radius and inside leg radii are greater than 0.80 mm.

Type 7

Type 7 channels are sometimes referred to as “top hats”. The web, flanges and legs may differ in thickness. They usually have a radius on the inside of the angle formedbetween the web and flange and between the flange and legs.The radii of the legs are less than or equal to 0.80 mm.

A

C

T1

T2

T3

B R3

R2

R1

AT2

T1

B

R1

R2

R3

A T2

T1

B

R1

R2

A

T2

T1

B

CR1

R2

16340 12.70 12.70 5.50 1.28 1.28 0.50 0.50 80 18 0.139282 22.24 9.54 9.52 2.04 5.64 0.78 0.64 89 24 0.234

16926 30.00 9.00 12.00 2.00 2.00 0.50 0.50 117 32 0.31416900 30.00 9.20 11.30 2.35 2.35 0.50 1.175 116 32 0.36416910 35.00 18.00 20.00 2.00 2.00 0.50 1.00 156 39 0.4202894 38.10 15.88 25.40 1.52 1.52 0.76 0.76 147 41 0.310H448 38.10 28.58 12.70 3.18 3.18 0.76 0.76 218 48 0.92716942 41.60 4.10 3.00 1.30 1.30 0.30 0.30 102 40 0.17816930 104.00 65.00 70.00 3.00 3.00 0.50 0.50 539 123 2.178

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

T2

mm

R1

mm

R2

mm

C

mm

Anod.

Peri.

C.C.D.

mm

16884 69.00 146.72 9.55 10.00 4.50 8.00 1.00 673 160 6.27016860 127.00 44.45 4.83 4.83 7.37 2.79 0.60 403 134 3.44516849 152.40 49.40 5.72 5.08 7.62 3.05 0.60 470 160 4.46416861 152.40 51.66 7.98 7.98 7.62 3.05 0.60 475 161 6.085

Est.

kg/m

Profile

Number

A

mm

B

mm

T1

mm

T2

mm

R1

mm

R2

mm

C

mm

Anod.

Peri.

C.C.D.

mm


16327 31.25 23.80 1.60 1.60 2.36 0.78 0.80 155 40 0.33416326 34.93 25.40 1.60 1.60 2.36 0.78 0.80 164 43 0.34716568 36.00 15.48 1.40 1.40 1.00 0.20 0.70 129 39 0.24116246 76.20 38.10 6.34 6.34 2.00 0.64 2.00 292 85 2.62016589 163.25 26.00 6.00 6.00 10.00 0.80 16.00 384 164 3.121

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

T2

mm

R1

mm

R2

mm

R3

mm

Profile

Number

A

mm

B

mm

T1

mm

Prev

Next

Pg 5

Extruded RodsAn extruded rod, or round bar, is a solid which is circular in shape.

6.00 19 6 0.0778.00 25 8 0.1369.00 28 9 0.172

10.00 31 10 0.20911.00 35 11 0.25812.00 38 12 0.30512.70 40 13 0.34313.00 41 13 0.36014.00 44 14 0.41515.00 47 15 0.47916.00 50 16 0.54518.00 57 18 0.69019.00 60 19 0.76820.00 63 20 0.85121.00 66 21 0.93922.00 69 22 1.03323.00 72 23 1.12625.00 79 25 1.33025.40 80 25 1.37326.00 81 26 1.43927.00 85 27 1.55028.00 88 28 1.66829.00 91 29 1.79030.00 94 30 1.91631.00 97 31 2.04532.00 101 32 2.18033.00 104 33 2.37135.00 110 35 2.607

A

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

36.00 113 36 2.75838.10 120 38 3.09040.00 126 40 3.41042.00 132 42 3.75544.00 138 44 4.12144.45 140 44 4.20345.00 141 45 4.31046.00 145 46 4.50448.00 151 48 4.90450.00 157 50 5.32150.80 160 51 5.49354.00 170 54 6.20455.00 173 55 6.44057.15 180 57 6.95260.00 189 60 7.66263.00 198 63 8.44865.00 204 65 8.99570.00 220 70 10.43171.00 223 71 10.72872.00 226 72 11.03475.00 236 75 11.97276.20 239 76 12.35980.00 251 80 13.62281.00 254 81 13.96585.00 267 85 15.37890.00 283 90 17.24095.00 298 95 19.209100.00 314 100 21.284

A

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m


A

28

Prev

Next

Pg 5

9.52 1.22* 41 10 0.08610.00 1.50 42 10 0.10910.00 1.22* 43 10 0.09112.00 2.00 50 12 0.17012.00 3.50 46 12 0.25312.00 1.00* 53 12 0.09412.70 1.62 55 13 0.15312.70 2.04 53 13 0.18512.70 2.64 52 13 0.22612.70 3.25 50 13 0.26112.70 1.22* 56 13 0.11914.00 1.80 60 14 0.18714.00 1.22* 62 14 0.13315.00 1.50 66 15 0.17215.00 2.00 64 15 0.22115.88 1.62 70 16 0.19715.88 2.00 69 16 0.23615.88 3.18 65 16 0.34415.88 1.22* 71 16 0.15216.00 1.50 71 16 0.18516.00 2.00 69 16 0.23816.00 2.75 67 16 0.31016.00 4.00 63 16 0.40816.00 1.20* 72 16 0.15118.00 1.22* 81 18 0.17418.00 1.50 80 18 0.21118.00 2.00 79 18 0.27219.00 1.50 85 19 0.22319.00 3.20 79 19 0.43019.06 1.62 85 19 0.24019.06 2.00 84 19 0.29019.06 3.18 80 19 0.43019.06 4.53 76 19 0.56019.06 1.22* 86 19 0.18520.00 1.50 90 20 0.23620.00 2.00 88 20 0.30620.00 3.00 85 20 0.43420.00 6.00 75 20 0.71520.00 1.20* 90 20 0.19222.00 1.50 99 22 0.26222.00 2.00 97 22 0.34022.00 2.50 96 22 0.41522.00 6.60 83 22 0.86522.22 1.22* 101 22 0.21822.22 1.62 100 22 0.28422.22 2.74 96 22 0.45422.22 3.18 95 22 0.51525.00 1.20* 114 25 0.24325.00 1.50 113 25 0.30025.00 2.00 112 25 0.39125.00 2.50 110 25 0.47925.00 3.00 108 25 0.56225.00 4.00 105 25 0.71525.00 5.00 102 25 0.851

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

25.00 8.25 92 25 1.17625.40 1.50 115 25 0.30525.40 1.62 115 25 0.32825.40 2.00 113 25 0.39825.40 2.64 111 25 0.51125.40 3.18 110 25 0.60125.40 4.76 105 25 0.83625.40 5.20 103 25 0.89425.40 6.35 100 25 1.02925.40 1.10* 116 25 0.22725.40 1.22* 116 25 0.25128.00 1.50 127 28 0.33828.00 3.75 120 28 0.77428.00 6.55 111 28 1.19628.58 1.62 130 29 0.37228.58 2.50 127 29 0.55528.58 3.98 122 29 0.83328.58 1.22* 131 29 0.28430.00 1.15* 138 30 0.28230.00 1.50 137 30 0.36430.00 2.00 135 30 0.47730.00 2.50 134 30 0.58530.00 3.00 132 30 0.68930.00 4.00 129 30 0.88530.00 5.00 126 30 1.06430.00 8.00 116 30 1.49831.00 2.00 140 31 0.49431.00 2.20 139 31 0.53931.75 1.40* 145 32 0.36231.75 1.62 145 32 0.41531.75 3.18 140 32 0.77331.75 6.35 130 32 1.37331.76 2.04 143 32 0.51632.00 1.50 146 32 0.38932.00 2.00 145 32 0.51132.00 2.50 143 32 0.62832.00 3.00 141 32 0.74032.00 4.25 137 32 1.00432.00 6.00 132 32 1.32832.50 8.62 126 33 1.75232.50 8.75 126 33 1.76835.00 1.60 160 35 0.45535.00 2.00 159 35 0.56235.00 3.00 156 35 0.81735.00 1.35* 161 35 0.38738.10 1.50 175 38 0.46738.10 1.62 174 38 0.50338.10 2.02 173 38 0.62038.10 3.18 170 38 0.94538.10 3.68 168 38 1.07838.10 4.06 167 38 1.17638.10 5.95 161 38 1.62838.10 6.36 160 38 1.71838.10 1.22* 176 38 0.383

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

W.T.

A

Extruded TubesAn extruded tube is a hollow of uniform thickness in the shape of a circle.Anodising Perimeter = outside perimeter + ½ inside perimeter.

29

* Alloy 6063 only.


Prev

Next

Pg 5

50.80 1.05* 236 51 0.44550.80 1.27* 235 51 0.53551.00 1.60 235 51 0.67351.00 3.00 231 51 1.22552.00 1.50 240 52 0.64552.00 3.00 236 52 1.25155.00 7.25 236 55 2.94656.00 3.00 254 56 1.35358.00 6.00 254 58 2.65558.00 8.50 247 58 3.58158.00 12.00 236 58 4.69860.00 1.20* 279 60 0.60060.00 1.68 277 60 0.83460.00 2.00 276 60 0.98760.00 2.50 275 60 1.22360.00 3.00 273 60 1.45560.00 3.60 271 60 1.72860.00 5.00 267 60 2.34060.85 9.80 256 61 4.25763.50 1.62 294 64 0.85363.50 2.50 291 64 1.29863.50 3.18 289 64 1.63263.50 4.78 284 64 2.38963.50 5.08 283 64 2.52663.50 6.00 280 64 2.93663.50 6.36 279 64 3.09363.60 13.48 257 64 5.75063.60 16.08 249 64 6.50365.00 1.68 301 65 0.90565.00 3.70 295 65 1.93065.00 9.00 278 65 4.28967.00 2.50 308 67 1.37268.00 9.38 291 68 4.67968.00 10.30 288 68 5.05870.00 1.27* 326 70 0.74370.00 2.25 323 70 1.29770.00 5.00 314 70 2.76672.50 6.00 323 73 3.39573.00 7.00 322 73 3.93275.00 1.20* 350 75 0.75475.00 2.50 346 75 1.54275.00 5.00 338 75 2.97975.00 15.00 306 75 7.65976.20 1.05* 356 76 0.67276.20 1.62 354 76 1.02876.20 2.00 353 76 1.26376.20 2.50 351 76 1.56876.20 3.18 349 76 1.97676.20 3.25 349 76 2.01876.20 4.76 344 76 2.89476.20 5.40 342 76 3.25476.20 6.36 339 76 3.78076.20 8.13 334 76 4.71076.20 9.53 329 76 5.407

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

40.00 1.65 183 40 0.53840.00 2.00 182 40 0.64740.00 2.50 181 40 0.79840.00 3.00 179 40 0.94540.00 3.18 179 40 0.99640.00 4.00 176 40 1.22540.00 5.00 173 40 1.48940.00 5.50 171 40 1.61540.00 9.00 160 40 2.37442.00 2.00 192 42 0.68142.00 2.50 190 42 0.84044.45 1.62 204 44 0.59044.45 6.35 190 44 2.05944.46 1.28* 205 44 0.47044.46 3.18 200 44 1.11745.00 2.00 206 45 0.73245.00 2.50 204 45 0.90445.00 3.00 203 45 1.07245.00 5.00 196 45 1.70245.00 5.50 195 45 1.84945.84 3.18 206 46 1.15446.00 3.00 207 46 1.09846.45 8.88 191 46 2.83946.45 9.63 189 46 3.01746.45 10.88 185 46 3.29346.70 2.80 211 47 1.04646.70 4.01 207 47 1.45746.70 5.08 204 47 1.79948.00 1.65 221 48 0.65148.00 2.50 218 48 0.96848.00 3.00 217 48 1.14948.00 4.50 212 48 1.66649.00 4.50 217 49 1.70450.00 1.00* 232 50 0.41750.00 1.20* 232 50 0.49850.00 1.50 231 50 0.61950.00 2.00 229 50 0.81750.00 2.50 228 50 1.01150.00 3.00 226 50 1.20050.00 3.50 225 50 1.38550.00 4.00 223 50 1.56650.00 5.00 220 50 1.91550.00 10.00 204 50 3.40450.80 1.22* 236 51 0.51550.80 1.62 234 51 0.67850.80 2.04 233 51 0.84650.80 2.54 231 51 1.04350.80 3.18 229 51 1.28950.80 3.25 229 51 1.31550.80 4.06 227 51 1.61550.80 4.78 224 51 1.87250.80 6.36 219 51 2.40550.80 8.23 214 51 2.98150.80 9.53 209 51 3.347

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

W.T.

A

Extruded Tubes - continued

An extruded tube is a hollow of uniform thickness in the shape of a circle.Anodising Perimeter = outside perimeter + ½ inside perimeter.

30

* Alloy 6063 only.


Prev

Next

Pg 5

76.20 11.35 323 76 6.26476.20 1.27* 355 76 0.81080.00 1.68 372 80 1.12080.00 3.00 368 80 1.96680.00 4.00 364 80 2.58780.00 5.00 361 80 3.19180.00 6.00 358 80 3.77880.00 8.00 352 80 4.90280.00 10.00 346 80 5.95780.00 12.50 338 80 7.18080.00 15.00 330 80 8.29780.00 16.00 327 80 8.71483.00 3.18 381 83 2.16085.00 3.50 390 85 2.42785.00 11.00 366 85 6.92786.00 3.00 396 86 2.11986.00 4.20 392 86 2.92486.00 18.38 348 86 10.57787.00 8.50 383 87 5.67889.00 2.00 413 89 1.48189.00 1.27* 415 89 0.94890.00 1.68 419 90 1.26390.00 1.98 418 90 1.48390.00 3.00 415 90 2.22190.00 5.00 408 90 3.61790.00 6.00 405 90 4.28990.00 7.12 402 90 5.02290.00 10.00 393 90 6.80896.00 3.00 443 96 2.37496.00 18.00 396 96 11.94897.00 3.50 446 97 2.785100.00 2.00 465 100 1.668100.00 3.00 462 100 2.476100.00 4.00 459 100 3.268100.00 5.00 456 100 4.042100.00 6.00 452 100 4.800100.00 8.00 446 100 6.263100.00 10.00 440 100 7.659100.00 12.00 434 100 8.987100.00 13.50 429 100 9.938100.00 15.00 424 100 10.850101.60 1.27* 475 102 1.084101.60 1.82 473 102 1.545101.60 2.04 472 102 1.728101.60 2.64 470 102 2.223101.60 3.18 469 102 2.663101.60 3.26 469 102 2.728101.60 3.66 467 102 3.050101.60 4.00 466 102 3.322101.60 4.76 464 102 3.923101.60 5.74 461 102 4.683101.60 6.36 459 102 5.155101.60 1.62* 474 102 1.378107.00 5.25 488 107 4.546

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

110.00 2.00 512 110 1.838110.00 5.00 503 110 4.468110.00 1.50* 514 110 1.385112.00 3.50 517 112 3.232112.00 7.75 503 112 6.876114.00 19.00 478 114 15.361114.30 3.18 529 114 3.007114.30 4.00 526 114 3.755114.30 6.36 519 114 5.842115.00 10.00 511 115 8.936118.00 2.50 548 118 2.457120.00 2.00 559 120 2.008120.00 3.00 556 120 2.987120.00 4.00 553 120 3.949120.00 5.00 550 120 4.893120.00 6.00 547 120 5.821120.00 8.00 540 120 7.625120.00 10.00 534 120 9.361120.00 15.00 518 120 13.403120.00 30.00 471 120 22.977120.00 1.50* 561 120 1.513125.00 2.50 581 125 2.606125.00 3.50 578 125 3.619125.00 4.00 576 125 4.119125.00 1.50* 584 125 1.576127.00 1.20* 595 127 1.285127.00 3.18 588 127 3.351127.00 3.50 587 127 3.678127.00 4.76 584 127 4.952127.00 5.00 583 127 5.191127.00 6.36 578 127 6.529127.00 1.50* 594 127 1.602130.00 10.00 581 130 10.212130.00 1.75* 607 130 1.910133.00 3.50 616 133 3.857133.00 4.00 614 133 4.391135.00 9.00 608 135 9.650138.00 2.25 643 138 2.599138.00 3.00 641 138 3.447139.70 9.50 628 140 10.526140.00 5.00 644 140 5.744140.00 8.00 635 140 8.987150.00 3.00 697 150 3.753150.00 5.00 691 150 6.170150.00 6.50 686 150 7.938150.00 8.00 682 150 9.667150.00 10.00 675 150 11.914152.40 2.00 712 152 2.560152.40 2.50 710 152 3.189152.40 3.25 708 152 4.125152.40 4.00 706 152 5.052152.40 5.00 702 152 6.272152.40 6.36 698 152 7.904152.40 9.50 688 152 11.553

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm



31

* Alloy 6063 only.

W.T.

A


Prev

Next

Pg 5



32

* Alloy 6063 only.

152.40 1.70* 713 152 2.180158.00 4.00 732 158 5.242160.00 1.85 748 160 2.490160.00 4.00 741 160 5.310160.00 5.00 738 160 6.595160.00 6.00 735 160 7.863160.00 10.00 723 160 12.765160.00 12.50 715 160 15.690162.00 2.20 756 162 2.992162.00 3.50 752 162 4.721165.10 6.36 758 165 8.592169.28 3.70 786 169 5.214

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

169.60 4.85 784 170 6.800169.60 9.25 770 170 12.622169.60 11.30 764 170 15.223177.80* 8.00 813 178 11.560180.00* 3.50 837 180 5.257180.00* 5.00 833 180 7.446180.00* 9.10 820 180 13.235185.00* 5.00 856 185 7.659185.00* 9.00 844 185 13.480185.00* 10.00 840 185 14.893185.00* 11.00 837 185 16.288

O.D.

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

W.T.

mm

W.T.

A


Prev

Next

Pg 5

10005 9.52 3.18 0.76 24 10 0.081101203 10.00 4.00 0.40 27 11 0.10810429 12.00 2.50 0.50 28 13 0.08110465 12.00 6.00 0.76 36 13 0.19510579 12.00 7.20 0.40 38 14 0.234

101132 12.70 3.18 0.40 31 13 0.109101192 12.70 4.76 0.40 34 13 0.164101194 12.70 6.35 0.40 37 14 0.21810015 12.70 9.52 0.40 44 16 0.328

101273 15.00 3.00 0.40 35 15 0.12210548 15.00 5.00 0.40 39 16 0.20310567 15.00 6.00 0.40 41 16 0.24310573 15.00 8.00 0.50 45 17 0.32410363 15.00 10.00 0.40 49 18 0.40610516 16.00 5.00 0.76 42 17 0.21710477 19.00 2.50 0.64 43 20 0.12910022 19.05 4.78 0.76 48 20 0.246

101131 19.06 3.18 0.50 44 19 0.16410023 19.06 6.36 0.40 50 20 0.32810024 19.06 9.52 0.40 56 21 0.491

101592 19.06 15.88 0.40 69 24 0.82010546 20.00 2.00 0.40 43 20 0.10810547 20.00 3.00 0.40 45 20 0.162

101274 20.00 4.00 0.40 47 20 0.21610568 20.00 5.00 0.40 49 20 0.27110503 20.00 6.00 0.50 52 21 0.325

101265 20.00 8.00 0.40 55 21 0.433101175 20.00 10.00 0.40 59 22 0.54210558 20.00 15.00 0.40 69 25 0.813

101504 20.00 17.00 0.50 73 26 0.92110027 22.13 3.18 0.76 49 23 0.19010577 25.00 2.00 0.40 53 26 0.135

101244 25.00 3.00 0.40 55 25 0.203101167 25.00 4.00 0.40 57 25 0.27110569 25.00 5.00 0.40 59 25 0.338

101261 25.00 6.00 0.40 61 26 0.406101176 25.00 8.00 0.40 65 26 0.542101243 25.00 10.00 0.40 69 27 0.677101209 25.00 15.00 0.40 79 29 1.01610559 25.00 20.00 0.40 89 32 1.35510229 25.40 2.38 0.76 54 26 0.162

101127 25.40 3.18 0.50 56 26 0.21810231 25.40 4.78 0.40 60 26 0.32510533 25.40 6.35 0.50 63 27 0.417

101547 25.40 7.94 0.50 66 26 0.546101134 25.40 9.53 0.40 70 27 0.656101158 25.40 12.70 0.40 76 28 0.874101551 25.40 15.88 0.40 82 30 1.093101162 25.40 19.05 0.40 88 32 1.31110509 30.00 2.00 0.25 64 30 0.163

101177 30.00 3.00 0.40 65 30 0.24410570 30.00 4.00 0.40 67 30 0.325

101178 30.00 5.00 0.40 69 30 0.40610560 30.00 6.00 0.40 71 30 0.487

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

101179 30.00 8.00 0.40 75 31 0.650101180 30.00 10.00 0.40 79 31 0.812101264 30.00 12.00 0.40 83 32 0.975101181 30.00 15.00 0.40 89 34 1.219101182 30.00 20.00 0.40 99 36 1.626101204 30.00 25.00 0.40 109 39 2.03210248 31.75 3.18 0.38 69 32 0.273

101191 31.75 12.70 0.40 88 34 1.09210249 31.76 4.78 0.76 73 32 0.41110250 31.76 6.36 0.40 76 33 0.54710251 31.76 9.52 0.76 83 33 0.81910167 31.76 15.88 0.40 95 36 1.36610253 31.76 19.06 0.76 100 37 1.639

101593 31.76 25.4 0.40 114 40 2.18610517 32.00 2.00 0.76 68 32 0.173

101313 34.00 3.00 0.50 73 35 0.27610469 34.00 8.00 0.76 84 35 0.73710378 34.92 3.18 0.76 75 35 0.300

101270 35.00 5.00 0.40 79 35 0.474101211 35.00 6.00 0.40 81 35 0.569101235 35.00 10.00 0.40 89 36 0.948101508 35.00 20.00 0.40 31 36 1.89710515 38.00 3.00 0.76 82 38 0.30910809 38.10 2.03 0.50 79 38 0.209

101135 38.10 3.18 0.40 82 38 0.328101165 38.10 4.78 0.40 85 39 0.49310534 38.10 6.35 0.50 88 39 0.655

101596 38.10 7.94 0.40 91 39 0.819101164 38.10 9.53 0.60 94 39 0.98310537 38.10 12.70 0.50 101 41 1.31110036 38.10 15.88 0.76 107 41 1.638

101136 38.10 19.05 0.40 114 43 1.967101155 38.10 25.40 0.40 126 46 2.622101575 38.10 31.75 0.40 139 49 3.278101212 40.00 2.00 0.40 83 40 0.216101213 40.00 3.00 0.40 85 40 0.32510561 40.00 4.00 0.40 87 40 0.433

101183 40.00 5.00 0.40 89 40 0.542101258 40.00 6.00 0.40 91 40 0.65010504 40.00 7.00 0.50 94 41 0.759

101184 40.00 8.00 0.40 95 41 0.86710730 40.00 10.00 0.40 99 42 1.084

101185 40.00 15.00 0.40 109 42 1.626101169 40.00 20.00 0.40 119 45 2.168101218 40.00 25.00 0.40 129 47 2.710101224 40.00 30.00 0.40 139 50 3.25210044 44.45 6.36 0.76 102 45 0.767

101585 44.45 7.94 0.40 104 45 0.956101586 44.45 15.88 0.40 120 47 1.913101546 44.45 19.06 0.50 126 48 2.295101537 44.45 25.40 0.40 139 51 3.060101588 44.45 31.75 0.40 152 54 3.82410042 44.46 3.18 0.76 94 45 0.38210043 44.65 4.78 0.64 98 45 0.574

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

Flat BarsType 1 flat bars have standard corner radii.

Type 1


AT

R1

Prev

Next

Pg 5

10045 44.65 9.52 0.76 108 46 1.148101221 45.00 3.00 0.40 95 45 0.366101609 45.00 10.30 0.50 110 46 1.256101606 45.00 17.50 0.50 124 48 2.134101607 45.00 19.50 0.50 128 49 2.37710493 45.00 20.00 0.50 129 50 2.438

101613 45.00 23.50 0.50 135 50 2.865101608 45.00 33.50 0.50 156 56 4.08510578 50.00 3.00 0.40 105 51 0.40610562 50.00 4.00 0.40 107 50 0.542

101186 50.00 5.00 0.40 109 50 0.677101272 50.00 6.00 0.40 111 50 0.813101269 50.00 8.00 0.40 115 51 1.084101298 50.00 10.00 0.40 119 51 1.355101217 50.00 12.00 0.40 123 51 1.626101187 50.00 15.00 0.40 129 52 2.03210555 50.00 20.00 0.40 138 54 2.71010544 50.00 25.00 0.50 149 56 3.40010575 50.00 27.00 0.50 153 57 3.657

101599 50.00 46.50 0.50 193 68 6.30110387 50.80 2.04 0.50 106 51 0.281

101137 50.80 3.18 0.40 107 51 0.437101138 50.80 4.76 0.40 110 51 0.65510535 50.80 6.35 0.50 113 52 0.874

101128 50.80 9.52 0.50 120 52 1.31010542 50.80 12.70 0.50 126 53 1.748

101159 50.80 15.88 0.40 133 53 2.186101139 50.80 19.05 0.40 139 54 2.62210540 50.80 25.40 0.40 152 57 3.496

101156 50.80 31.75 0.40 164 60 4.371101152 50.80 38.10 0.40 177 64 5.24510399 53.00 1.60 0.75 108 53 0.228

101306 54.00 2.00 0.50 111 54 0.29210740 54.00 3.18 0.40 114 55 0.465

101266 60.00 3.00 0.40 125 60 0.488101228 60.00 4.00 0.40 127 60 0.650101188 60.00 5.00 0.40 129 60 0.81310531 60.00 6.00 0.50 131 61 0.975

101267 60.00 8.00 0.40 135 61 1.3010563 60.00 12.00 0.40 143 61 1.95110550 60.00 15.00 0.40 149 62 2.43910564 60.00 25.00 0.40 169 65 4.065

101624 60.50 30.00 0.50 180 68 4.91810369 63.00 2.36 0.76 129 64 0.40210265 63.50 3.18 0.76 133 64 0.548

101589 63.50 4.76 0.40 136 64 0.819101166 63.50 6.35 0.40 139 64 1.09210267 63.50 7.96 0.76 142 64 1.368

101140 63.50 9.53 0.40 145 65 1.640101130 63.50 12.70 0.50 152 65 2.18510270 63.50 15.88 0.76 157 66 2.731

101154 63.50 19.05 0.40 164 66 3.278101151 63.50 25.40 0.40 177 69 4.37110273 63.50 31.76 0.76 189 71 5.464

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

101153 63.50 38.10 0.40 203 74 6.556101572 63.50 50.80 0.40 228 81 8.74210552 70.00 5.00 0.40 149 70 0.948

101268 70.00 10.00 0.40 159 71 1.897101245 75.00 1.40 0.50 152 75 0.28410490 75.00 6.50 0.76 163 75 1.32110958 75.00 7.54 0.40 164 76 1.532

101300 75.00 8.00 0.40 165 75 1.62610449 75.00 9.50 0.80 168 76 1.92910726 75.00 12.00 0.76 173 76 2.438

101317 75.00 13.50 0.50 176 77 2.743101332 75.00 15.50 0.40 180 77 3.150101335 75.00 17.50 0.40 184 77 3.55710829 75.00 19.00 0.50 187 77 3.861

101555 75.00 20.00 0.50 189 77 4.064101560 75.00 23.00 0.50 195 79 4.674101563 75.00 25.00 0.50 199 79 5.08110512 76.20 1.91 0.50 155 77 0.39410279 76.20 2.54 0.25 157 76 0.524

101141 76.20 3.18 0.40 158 76 0.65610280 76.20 4.78 0.40 161 76 0.98710541 76.20 6.35 0.50 164 77 1.31110286 76.20 8.53 0.79 170 77 1.966

101129 76.20 9.52 0.50 171 77 1.96510538 76.20 12.70 0.50 177 78 2.62210289 76.20 15.88 0.76 182 78 3.280

101123 76.20 19.05 0.40 190 79 3.934101126 76.20 25.40 0.50 202 80 5.245101157 76.20 31.75 0.40 215 83 6.556101124 76.20 38.10 0.50 228 85 7.867101142 76.20 50.80 0.40 253 92 10.490101286 80.00 3.00 0.40 165 80 0.65010565 80.00 4.00 0.40 167 80 0.86710566 80.00 5.00 0.40 169 80 1.084

101238 80.00 6.00 0.40 171 80 1.300101189 80.00 8.00 0.40 175 80 1.734101240 80.00 10.00 0.40 179 81 2.168101168 80.00 15.00 0.40 189 81 3.25210551 80.00 20.00 0.40 199 83 4.33610553 80.00 25.00 0.40 209 84 5.420

101173 80.00 30.00 0.40 219 85 6.503101628 80.00 41.00 0.40 241 90 8.888101524 80.00 50.00 0.75 259 94 10.839101649 80.00 70.00 0.50 299 106 15.17510925 84.00 5.00 0.50 177 85 1.138

101587 88.90 3.18 0.40 183 89 0.76610074 88.90 6.36 0.64 191 90 1.531

101598 88.90 7.94 0.40 193 89 1.91310319 88.90 9.53 0.64 197 89 2.298

101578 88.90 12.70 0.40 203 90 3.05910076 88.90 15.88 0.76 208 91 3.824

101574 88.90 19.05 0.40 215 91 4.589101573 88.90 25.40 0.40 228 92 6.119101229 90.00 5.00 0.40 189 90 1.219

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

Flat Bars Type 1continued

Type 1 flat bars have standard corner radii.


AT

R1

Prev

Next

Pg 5

Flat Bars Type 1 flat bars have standard corner radii.

Type 1continued

35

AT

R1

101597 100.00 3.00 0.40 205 100 0.81310365 100.00 5.00 0.76 209 100 1.355

101234 100.00 6.00 0.40 211 101 1.626101190 100.00 10.00 0.40 219 101 2.71010946 100.00 12.50 0.50 224 101 3.387

101236 100.00 15.00 0.40 229 102 4.065101170 100.00 20.00 0.40 239 102 5.419101171 100.00 25.00 0.40 249 102 6.775101282 100.00 30.00 0.40 259 104 8.12910409 101.60 2.04 0.75 206 102 0.56010321 101.60 3.18 0.25 209 103 0.87510081 101.60 4.77 0.76 213 102 1.31510536 101.60 6.35 0.50 215 102 1.748

101581 101.60 7.94 0.40 218 102 2.186101144 101.60 9.53 0.40 222 102 2.62410539 101.60 12.70 0.50 228 105 3.49610209 101.60 15.88 0.76 234 103 4.373

101145 101.60 19.05 0.40 241 103 5.245101146 101.60 25.40 0.40 253 104 6.993101571 101.60 31.75 0.50 266 106 8.741101640 101.60 40.00 0.60 282 109 11.013101122 101.60 50.80 0.50 304 113 13.986101528 101.60 63.50 0.80 329 120 17.482101206 120.00 5.00 0.40 249 121 1.626101208 120.00 6.00 0.40 251 121 1.951101237 120.00 10.00 0.40 259 120 3.252101113 120.00 20.00 0.50 279 122 6.503101594 120.00 25.00 0.40 289 124 8.130101207 120.00 30.00 0.40 299 124 9.75610094 127.00 6.35 0.76 267 127 2.18710095 127.00 9.52 0.65 273 127 3.28110096 127.00 12.70 0.64 279 128 4.375

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

10216 127.00 15.88 0.76 284 128 5.46710324 127.00 19.04 0.64 291 129 6.55210097 127.00 25.40 0.64 305 130 8.749

101214 130.00 10.00 0.40 279 130 3.523101591 140.00 6.00 0.40 291 140 2.276101202 140.00 10.00 0.40 299 140 3.794101115 140.00 20.00 0.50 319 141 7.587101595 140.00 25.00 0.50 329 142 9.48410791 140.00 45.00 0.80 369 147 17.0710941 149.50 3.18 0.80 304 150 1.287

101231 150.00 5.00 0.40 309 150 2.03010979 150.00 7.90 0.76 316 150 3.211

101200 150.00 10.00 0.40 319 151 4.065101527 150.00 12.00 0.40 323 150 4.877101279 150.00 15.00 0.40 329 151 6.09710358 152.40 3.18 0.76 311 153 1.311

101583 152.40 4.76 0.40 314 152 1.965101147 152.40 6.35 0.40 317 153 2.622101577 152.40 7.94 0.40 320 153 3.279101148 152.40 9.53 0.40 323 154 3.936101149 152.40 12.70 0.40 330 153 5.24510104 152.40 15.88 0.76 335 153 6.55710105 152.40 19.06 0.76 343 154 7.87510106 152.40 25.40 0.76 356 155 10.499

101630 155.00 90.00 5.00 481 179 37.74610777 160.00 10.00 0.80 339 161 4.33410704 165.10 12.70 0.80 354 166 5.68010921 200.00 10.00 0.80 419 200 5.418

101289 200.00 20.00 0.40 439 201 10.839101602 200.00 25.00 0.50 449 201 13.55010360 228.60 9.52 0.76 475 229 5.896

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm


Prev

Next

Pg 5

Flat Bars

36

Type 2

Type 2 flat bars have radii of more than 0.80 mm on the top corners.The other two corners have radii of less than or equal to 0.80 mm.

Type 3

Type 3 flat bars have radius so that the sum of the two side radii mustequal the thickness of the bar.

AT

R1

R2

AT

R1

R2

10114 25.40 3.18 1.60 0.64 56 26 0.215101307 28.58 3.18 0.30 1.20 60 30 0.22910118 31.75 3.18 1.60 0.64 70 32 0.27110122 38.00 3.00 1.50 0.64 81 38 0.325

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

R2

mm

10132 12.70 3.18 1.60 1.60 29 13 0.103101199 18.00 8.00 4.00 4.00 45 18 0.35310351 24.77 7.92 3.96 3.96 59 26 0.49510142 25.40 3.18 1.60 1.60 57 26 0.21310397 44.20 3.74 1.86 1.86 95 45 0.439

101281 70.00 20.00 10.00 10.00 163 70 3.561101518 70.00 30.00 15.00 15.00 174 70 5.16610492 75.00 1.90 0.95 0.95 152 75 0.38410157 76.20 3.18 1.58 1.58 156 76 0.650

101516 82.00 26.00 13.00 13.00 194 82 5.384

Est.

kg/m

Profile

Number

A

mm

T

mm

R1

mm

Anod.

Peri.

C.C.D.

mm

R2

mm


Prev

Next

Pg 5

31.76 0.40 126 45 2.73335.00 0.40 139 49 3.31938.10 0.40 152 54 3.93340.00 2.50 156 56 4.32145.00 0.40 179 63 5.48750.00 0.40 199 70 6.774

39955 50.80 0.76 202 72 6.99257.15 0.40 228 80 8.85160.00 0.76 239 85 9.75563.50 0.76 253 89 10.92665.00 2.00 257 92 11.44070.00 0.40 279 99 13.27976.20 0.60 304 107 15.73590.00 3.00 355 123 21.930

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

R

mm

Square Bars A square bar is a solid with all four sides equal in length.It is identified by size across the flats.

37

R

A

Hexagonal Bars A hexagonal is a solid with six equal sides.All corners will be broken with radii less than or equal to 0.80 mm.It is identified by the size measurement across the flats.

AR

6.35 0.80 24 9 0.1088.00 0.50 31 11 0.173

10.00 0.40 39 14 0.27112.00 0.50 47 17 0.39012.70 0.40 50 18 0.437

38101 15.00 0.50 59 21 0.60916.00 0.40 63 22 0.69318.00 0.40 71 25 0.87819.06 0.76 75 27 0.98320.00 0.40 79 28 1.08422.00 0.50 87 31 1.311

101326 25.00 0.40 99 35 1.69325.40 0.40 101 36 1.74830.00 0.40 119 42 2.439

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

R

mm

9.50 0.76 33 9 0.21210.00 0.50 34 12 0.23411.00 0.50 38 13 0.28412.70 0.76 44 15 0.37813.00 0.50 45 15 0.39714.00 0.76 48 16 0.45817.00 0.50 59 20 0.67818.04 0.76 62 21 0.76319.00 0.76 66 22 0.84720.82 0.76 72 24 1.017

A

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

R

mm

21.00 0.76 73 24 1.03522.00 0.50 76 25 1.13624.00 0.50 83 29 1.35225.00 0.50 87 29 1.46727.00 0.25 93 31 1.71027.94 0.76 96 32 1.83230.00 0.50 104 35 2.11232.00 0.50 111 37 2.40345.50 0.76 153 53 4.859

A

mm

Anod.

Peri.

C.C.D.

mm

Est.

kg/m

R

mm


Prev

Next

Pg 5

Rectangular Hollows A rectangular hollow is a hollow of uniform thickness in the shape of a rectangle.The inside corner radii may or may not equal the outside corner radii.

38

H6545 15.00 10.00 1.50 0.40 0.40 68 18 0.179H5441 17.20 10.90 1.70 0.75 1.20 75 20 0.225H1485 18.00 12.00 1.20 0.76 0.76 84 22 0.180H4932 20.00 10.00 1.50 0.40 0.40 83 22 0.220H6560 20.00 10.00 2.00 0.40 0.40 81 22 0.282H6543 20.00 10.00 3.00 0.40 0.40 77 22 0.390H4895 20.00 15.00 2.00 0.40 0.40 96 25 0.336H6932 24.00 18.00 1.20 2.30 3.50 113 30 0.241H3303 25.00 12.00 2.00 0.50 0.50 103 28 0.358H4993 25.00 15.00 1.50 0.40 0.40 113 29 0.301H4729 25.00 15.00 2.00 0.40 0.40 111 29 0.390H6067 25.00 16.00 2.00 0.20 0.20 114 30 0.401H4730 25.00 20.00 2.00 0.40 0.40 126 32 0.444H4125 25.20 20.00 2.00 1.50 2.50 122 32 0.437H4318 25.35 14.60 1.30 1.00 1.00 112 29 0.263H6441 25.40 12.70 3.18 0.50 0.50 100 28 0.547H5440 28.40 12.40 1.70 0.80 1.40 113 31 0.341H4091 30.00 10.00 1.50 0.50 0.50 114 32 0.300H6918 30.00 16.00 1.75 6.25 8.00 112 34 0.344H5894 30.00 19.00 1.30 0.75 0.75 140 35 0.327H4765 30.00 20.00 1.50 0.40 0.40 143 36 0.382H4707 30.00 20.00 2.00 0.40 0.40 141 36 0.499H1561 33.00 20.00 1.25 2.25 3.50 146 39 0.325H2497 33.00 20.00 1.50 2.00 3.50 145 39 0.388H4912 34.00 20.00 2.00 0.40 0.40 153 39 0.542H5852 34.92 25.40 1.30 1.08 2.38 171 44 0.396H7207 34.92 25.40 1.30 0.78 2.38 171 43 0.395H4856 34.92 25.40 1.60 0.78 2.38 170 41 0.484H7385 35.00 12.00 1.50 0.30 0.30 134 37 0.358H4893 35.00 20.00 2.00 0.40 0.40 156 40 0.553H4205 35.00 25.00 1.20 0.50 0.50 175 43 0.370H6486 35.00 25.00 1.40 1.00 2.40 165 43 0.423H1885 35.00 25.00 1.50 11.00 12.50 143 35 0.381H6541 35.00 25.00 2.00 0.40 0.40 171 43 0.607H8339 38.00 15.00 1.50 0.40 0.40 152 41 0.407H8161 38.00 25.00 1.50 1.50 3.00 177 43 0.472H8340 38.00 27.00 1.50 0.40 0.40 188 46 0.504H1568 38.10 19.00 3.17 0.25 0.25 159 43 0.880H8088 38.10 19.05 1.63 0.40 0.40 164 43 0.476H4605 38.10 25.40 1.57 1.60 3.18 177 46 0.498H8047 38.10 25.40 3.25 0.40 0.40 176 46 1.004H2547 40.00 20.00 1.20 3.80 5.00 163 45 0.350H4689 40.00 20.00 2.00 0.40 0.40 171 44 0.607H6641 40.00 20.00 3.00 0.40 0.40 167 45 0.878H4900 40.00 25.00 2.00 10.50 12.50 157 40 0.554H4764 40.00 30.00 2.00 0.40 0.40 201 50 0.715H4952 40.00 30.00 2.50 0.40 0.40 199 50 0.881H4963 40.00 30.00 3.00 0.40 0.40 197 50 1.041H4996 40.00 30.00 4.00 0.40 0.40 193 50 1.344H7043 42.88 27.94 1.27 0.20 0.20 207 51 0.469H8341 44.00 37.00 1.50 0.40 0.40 236 57 0.634H0102 44.46 25.40 3.18 0.64 0.64 195 51 1.083H2591 45.00 20.00 1.20 1.80 3.00 184 49 0.396H7495 45.00 20.00 1.20 1.00 0.50 129 49 0.409

Profile

Number

A

mm

B

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.

TR1

R2

A

B


Prev

Next

Pg 5

Rectangular Hollows - continued A rectangular hollow is a hollow of uniform thickness in the shape of a rectangle.The inside corner radii may or may not equal the outside corner radii.

39


Profile

Number

A

mm

B

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.

TR1

R2

A

B


Prev

Next

Pg 5

A rectangular hollow is a hollow of uniform thickness in the shape of a rectangle.The inside corner radii may or may not equal the outside corner radii.

Rectangular Hollows - continued

40


Profile

Number

A

mm

B

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.

TR1

R2

A

B


Prev

Next

Pg 5

A rectangular hollow is a hollow of uniform thickness in the shape of a rectangle.The inside corner radii may or may not equal the outside corner radii.

41

TR1

R2

A

BRectangular Hollows - continued

H4962 150.00 50.00 2.50 0.50 0.50 589 158 2.642H8166 150.00 50.00 3.00 0.50 0.50 587 158 3.154H4738 150.00 50.00 4.00 0.40 0.40 583 158 4.163H4732 150.00 100.00 3.00 0.40 0.40 737 180 3.968H4521 152.40 50.80 3.18 0.50 0.50 596 161 3.393H8131 152.40 76.20 9.53 0.40 0.40 647 170 10.823H4735 160.00 40.00 4.00 0.40 0.40 583 165 4.163H4739 160.00 60.00 5.00 0.40 0.40 639 171 5.691H4733 180.00 40.00 4.00 0.40 0.40 643 184 4.596H3308 190.00 80.00 3.00 0.50 0.50 707 206 4.292H8207 197.00 97.00 8.50 0.50 0.50 847 220 12.761H3176 200.00 50.00 3.00 0.50 0.50 737 206 3.967H4917 200.00 50.00 4.00 0.40 0.40 733 206 5.247

Profile

Number

A

mm

B

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.


Prev

Next

Pg 5

Square Hollows A square hollow is a hollow of uniform thickness in the shape of a square.The inside corner radii may or may not equal the outside corner radii.

T

R1

R2

A

42

H6542 10.00 2.00 0.40 0.40 51 14 0.173H5433 12.00 1.20 0.30 0.30 66 17 0.140H7511 12.70 1.57 0.40 0.40 69 18 0.189H6912 15.00 1.50 0.40 0.40 83 21 0.219H4918 15.00 2.00 0.40 0.40 81 21 0.282H4570 15.88 1.57 0.40 0.40 88 22 0.244H2564 18.00 1.20 0.76 0.76 102 25 0.219H4084 19.00 1.20 0.50 0.50 109 27 0.231H7512 19.05 1.58 0.40 0.40 107 27 0.299H4571 19.05 3.18 0.40 0.40 101 27 0.547H0823 19.06 1.62 0.40 0.40 107 27 0.306H5958 20.00 1.20 0.50 0.50 114 28 0.244H6913 20.00 1.50 0.40 0.40 113 28 0.301H6539 20.00 2.00 0.40 0.40 111 28 0.390H5836 21.00 1.30 0.40 0.40 120 29 0.277H0012 22.22 1.90 1.27 3.18 119 30 0.398H7312 25.00 1.20 0.50 0.50 144 35 0.310H7573 25.00 1.50 0.50 1.50 141 35 0.377H6429 25.00 2.00 0.50 0.50 141 35 0.499H4944 25.00 3.00 0.40 0.40 137 35 0.715H4415 25.40 1.60 0.40 0.40 146 36 0.413H0175 25.40 2.04 2.38 0.64 141 36 0.529H0315 25.40 3.18 1.60 1.60 136 36 0.766H7509 25.40 3.18 0.40 0.40 139 36 0.766H4668 25.40 3.25 0.40 0.40 139 36 0.780H7413 27.00 1.50 0.50 0.50 155 38 0.405H4971 30.00 2.00 1.00 3.00 166 40 0.588H6540 30.00 2.00 0.40 0.40 171 42 0.607H4690 30.00 3.00 0.40 0.40 167 42 0.878H3002 30.76 1.63 0.80 0.80 178 44 0.514H5037 31.75 1.60 0.40 0.40 183 45 0.523H6450 31.75 3.18 0.50 0.50 176 45 0.985H4759 31.75 3.25 0.40 0.40 176 45 1.000H2256 31.76 2.00 0.64 0.64 181 45 0.645H4964 34.00 3.00 0.40 0.40 191 48 1.010H5291 34.93 1.60 4.75 6.35 188 49 0.536H8452 34.93 2.13 4.22 6.35 187 49 0.705H6559 35.00 2.00 0.40 0.40 201 49 0.715H2105 38.00 3.00 0.76 0.76 214 54 1.139H8430 38.10 1.60 1.40 3.00 205 54 0.617H4669 38.10 1.63 0.40 0.40 221 54 0.644H0041 38.10 2.00 0.40 0.40 220 54 0.782H6451 38.10 3.18 0.50 0.50 215 54 1.204H4666 38.10 3.25 0.40 0.40 215 54 1.228H0363 38.10 4.78 0.76 1.28 207 54 1.728H6496 40.00 1.50 0.30 1.27 232 56 0.622H4643 40.00 2.00 0.40 0.40 231 56 0.824H4722 40.00 2.50 0.40 0.40 229 56 1.017H6636 40.00 2.50 2.50 5.00 219 57 0.973H4660 40.00 3.00 0.40 0.40 227 56 1.203H6436 40.00 4.00 0.76 0.76 222 56 1.561H3855 44.46 3.18 0.50 1.00 254 63 1.420H6217 50.00 1.50 5.50 7.00 277 71 0.744H3121 50.00 2.00 0.50 0.50 283 70 1.041

Profile

Number

A

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.


Prev

Next

Pg 5

Square Hollows - continued A square hollow is a hollow of uniform thickness in the shape of a square.The inside corner radii may or may not equal the outside corner radii.

43

T

R1

R2

A

H4720 50.00 2.50 0.40 0.40 289 70 1.287H6640 50.00 3.00 0.40 0.40 247 70 1.528H4661 50.00 4.00 0.40 0.40 283 70 1.995H4670 50.80 1.63 0.40 0.40 297 72 0.869H8167 50.80 2.03 4.00 6.00 283 70 1.026H2309 50.80 3.18 0.50 0.50 292 72 1.643H4754 50.80 3.25 0.40 0.40 291 72 1.675H0256 50.80 3.26 1.60 1.60 288 72 1.680H4576 50.80 6.35 0.40 0.40 278 72 3.060H6544 60.00 3.00 0.40 0.40 347 85 1.854H4574 63.50 3.18 0.40 0.40 367 90 2.079H3557 72.60 2.00 3.75 0.50 424 103 1.563H4316 75.00 3.00 0.50 0.50 438 106 2.341H6452 76.20 3.18 0.50 0.50 443 108 2.517H8143 76.20 3.25 0.40 0.40 442 107 2.570H4577 76.20 6.35 0.40 0.40 431 107 4.808H2268 78.00 2.00 2.00 0.50 461 110 1.656H4934 80.00 3.00 0.40 0.40 467 113 2.504H4919 80.00 4.00 0.40 0.40 463 113 3.295H8100 100.00 2.00 0.40 0.40 590 141 2.125H4887 100.00 3.00 0.50 0.50 587 141 3.154H3012 100.00 4.00 0.80 0.80 584 141 4.163H2027 100.00 6.00 0.80 0.80 574 141 6.113H4894 100.00 8.00 5.00 0.50 563 141 8.035H8085 101.60 3.25 0.40 0.40 594 143 3.465H8056 101.60 6.35 0.40 0.40 582 143 6.556H1673 114.50 3.00 1.00 1.00 672 162 3.630H4746 125.00 6.00 0.40 0.40 725 176 7.740H8228 125.00 8.00 0.50 0.50 715 176 10.146H4575 127.00 3.18 0.40 0.40 748 180 4.268H8276 127.00 6.35 0.40 0.40 736 179 8.305H4525 150.00 2.50 0.50 0.50 889 212 3.997H4519 152.40 3.18 0.50 0.50 900 216 5.144H1671 160.00 3.00 1.00 1.00 945 226 5.106

Profile

Number

A

mm

T

mm

C.C.D.

mm

Est.

kg/m

R1

mm

R2

mm

Anod.

Peri.


Prev

Next

Pg 5

I - SectionsI - sections may have web and flanges of different thicknesses.They will have radii (R) in the corners formed between the web and flanges.2

The outside corners of the flanges have a radius, (R).1

A

B

R1R2

T2

T1

44

17010 9.52 21.44 1.58 2.38 0.76 0.76 96 23 0.22417211 13.50 22.00 1.75 1.75 0.40 0.40 109 26 0.25617068 15.62 6.36 1.02 1.02 0.50 0.50 52 17 0.07217108 15.88 15.88 1.60 0.76 0.80 0.80 88 23 0.19117131 16.60 19.06 1.30 1.30 0.60 0.25 105 25 0.18317401 17.48 9.53 1.60 1.60 0.30 0.30 84 20 0.17917110 19.52 19.52 1.26 1.26 0.50 0.50 112 28 0.19117123 21.00 21.00 1.20 1.20 0.60 0.30 121 30 0.19517515 22.00 22.00 3.00 2.00 0.90 0.90 128 31 0.44417043 23.24 22.98 1.40 1.40 0.76 0.76 136 33 0.25117207 32.00 20.00 1.50 1.50 0.50 0.50 138 38 0.28017107 47.83 27.50 1.50 1.50 0.30 0.30 203 53 0.40617528 48.00 50.00 2.00 2.00 4.00 0.50 290 68 0.77517408 48.50 27.40 2.00 2.00 0.64 0.64 203 56 0.53917022 48.90 19.06 2.04 2.04 0.76 0.76 170 52 0.45717209 49.00 78.00 2.00 2.00 1.00 0.50 402 92 1.08517102 50.00 65.00 5.00 5.00 1.50 4.00 338 82 2.33017411 50.80 50.80 3.18 3.18 0.25 3.18 292 72 1.28217514 51.40 150.00 6.00 6.00 1.50 1.50 707 159 5.70917415 57.20 25.40 1.60 1.60 0.76 0.50 209 63 0.45217071 63.50 44.46 3.18 3.18 0.64 3.18 293 78 1.28117206 71.00 44.00 2.10 1.60 0.50 0.50 323 84 0.80917127 75.60 19.70 1.30 1.30 0.20 0.20 226 79 0.39617208 76.00 20.00 1.50 1.50 0.50 0.50 226 79 0.45917502 120.00 120.00 10.00 10.00 1.00 7.00 686 170 9.32317013 127.00 76.20 9.52 6.36 0.64 9.40 530 148 6.00417529 130.00 50.00 6.00 4.00 0.40 4.00 444 139 2.94217073 130.00 100.00 5.00 5.00 0.76 5.00 598 164 4.39217527 150.00 150.00 3.80 3.80 0.50 3.00 885 211 4.57617098 150.00 150.00 12.00 10.00 1.00 8.00 880 212 13.32017069 152.40 101.60 6.36 6.36 0.78 0.78 694 183 5.89917092 177.80 101.60 9.54 9.54 0.76 0.76 739 205 9.35617507 177.80 101.60 11.11 7.94 1.50 11.50 746 205 9.76017087 177.80 101.60 12.70 12.70 0.76 0.76 737 205 12.24917091 203.20 101.60 11.12 7.94 0.80 11.43 775 227 10.320

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

B

mm

T1

mm

T2

mm

R1

mm

R2

mm


Prev

Next

Pg 5

Tees Type 1 tees are of a uniform thickness.The head and body of the tee may not be equal in length.All radii are less than or equal to 0.80 mm.

Type 1

45

A

B

T

T

R1

14518 15.00 15.00 1.50 0.40 59 19 0.11514005 19.06 19.06 3.18 0.64 74 24 0.30014538 20.00 11.25 1.25 0.50 62 21 0.10314214 20.00 20.00 1.50 0.40 79 28 0.15914006 22.04 46.06 3.00 0.20 136 48 0.53014116 22.20 22.20 2.00 0.25 88 31 0.22914108 22.20 22.20 3.00 0.50 89 52 0.33714013 22.22 45.24 3.18 0.64 133 48 0.55314117 25.00 25.00 1.60 0.30 99 32 0.20914017 25.40 25.40 3.18 0.64 99 31 0.40914085 25.40 31.75 1.28 0.38 114 36 0.12014019 25.40 38.10 3.18 0.64 127 41 0.52014091 25.40 44.45 3.18 0.20 139 49 0.57414511 30.00 30.00 3.00 0.40 119 38 0.46314215 35.00 35.00 3.00 0.40 139 44 0.54414032 38.10 12.70 1.14 0.50 100 39 0.15314067 38.10 38.10 2.38 0.80 153 48 0.47514536 38.10 38.10 6.35 0.76 151 48 1.20114068 38.45 38.45 3.20 0.63 154 48 0.62914121 40.00 20.00 3.00 0.20 119 41 0.46314209 40.00 40.00 3.00 0.40 159 50 0.62614512 40.00 40.00 4.00 0.40 159 50 0.82314128 42.00 42.00 2.00 0.50 168 53 0.44414096 50.00 25.00 3.00 0.80 150 36 0.58414506 50.00 50.00 4.00 0.40 199 62 1.04014520 50.80 31.75 6.35 0.30 164 53 1.31114500 50.80 50.80 3.18 0.40 202 64 0.84814507 60.00 60.00 4.00 0.40 239 75 1.25714508 60.00 60.00 6.00 0.40 239 75 1.85314529 76.20 76.20 6.36 0.40 303 96 2.51714505 100.00 60.00 5.00 0.40 319 116 2.100

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

T

mm

R1

mm

B

mm


Prev

Next

Pg 5

14408 19.00 15.87 2.36 1.60 0.75 72 23 0.22514103 30.00 20.00 2.00 0.50 1.00 98 32 0.22114524 32.00 75.00 6.00 3.00 0.50 210 79 1.65214047 38.10 38.10 4.78 5.84 0.64 147 48 0.96414202 38.10 50.80 6.36 3.00 0.50 178 56 1.42514531 50.00 75.00 5.00 6.00 0.40 244 84 1.66814532 50.00 100.00 5.00 6.00 0.40 294 107 2.00614530 50.80 50.80 6.00 5.00 0.40 198 64 1.58314050 50.80 50.80 6.36 6.36 0.64 198 58 1.68714112 56.00 38.00 4.00 1.00 10.00 179 66 1.03914522 60.00 86.00 6.00 3.00 0.80 284 105 2.05014052 63.50 63.50 6.36 6.36 0.64 247 73 1.68714523 65.00 100.00 8.00 3.00 0.50 326 111 3.41314129 70.00 80.00 3.18 3.18 0.50 296 95 1.27614502 76.00 76.00 6.50 7.00 0.50 297 95 2.61914533 76.20 152.40 9.50 9.52 1.00 446 162 5.74314043 99.40 51.30 3.15 0.82 0.82 298 72 1.25814503 102.00 102.00 6.50 7.00 0.50 401 128 3.53514058 127.00 101.60 9.52 9.90 0.76 447 141 5.76414097 152.40 76.20 9.50 9.52 1.00 446 153 5.749

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

T

mm

R1

mm

B

mm

R2

mm

Tees Type 2 tees are of a uniform thickness.The head and body of the tee are not equal in length.The inside corners have a radius.

Type 2

46

Z - Sections Z - sections are profiles in the shape of a “Z” with a uniform thickness throughout.The radii are all less than or equal to 0.80 mm

B

C

T2

T1A

A

B

T

T

R1

17128 10.50 12.00 12.00 2.00 2.00 63 26 0.165736 15.88 25.40 19.05 3.17 3.18 114 44 0.559

38396 25.00 17.00 17.00 2.00 2.00 113 41 0.29838398 25.00 25.00 25.00 2.00 2.00 145 54 0.385

33 28.58 19.05 19.06 3.18 3.18 159 45 0.54038397 40.00 40.00 40.00 3.00 3.00 233 87 0.926

Est.

kg/m

Profile

Number

A

mm

Anod.

Peri.

C.C.D.

mm

C

mm

T1

mm

B

mm

T2

mm


R2

Prev

Next

Pg 5

Type 1 Equal angle, no radius

Hulam

in Extrusions Standard Profile C

atalogue4

7 En

gin

ee

ring

Da

ta fo

r Stru

ctura

l Sh

ap

es

AngleT

o90

A

A

T

y 2

Cyy

Cx

1

x

21

x

15137 12.70 1.60 0.76 0.10 38.1 3.8 3.8 0.6 64 3.9 0.6 64 3.9 0.9 101 4.9 0.2 44 2.5 45 32

15554 12.70 3.18 0.40 0.19 70.7 4.3 4.3 1.0 114 3.7 1.0 114 3.7 1.5 165 4.6 0.4 72 2.5 45 238

15139 14.00 2.00 0.76 0.14 52.0 4.2 4.2 0.9 95 4.2 0.9 95 4.2 1.5 149 5.3 0.4 65 2.7 45 69

150021 15.00 1.25 0.40 0.10 35.9 4.2 4.2 0.8 72 4.7 0.8 72 4.7 1.2 117 5.9 0.3 53 3.0 45 19

15579 15.00 1.50 0.40 0.12 42.8 4.3 4.3 0.9 85 4.6 0.9 85 4.6 1.5 137 5.8 0.4 61 2.9 45 32

15574 15.00 2.00 0.40 0.15 56.0 4.5 4.5 1.2 110 4.6 1.2 110 4.6 1.8 173 5.7 0.5 76 2.9 45 75

15565 15.00 3.00 0.40 0.22 81.0 4.8 4.8 1.6 156 4.4 1.6 156 4.4 2.5 235 5.5 0.7 101 2.9 45 243

15992 15.88 1.59 0.40 0.13 48.0 4.6 4.6 1.1 101 4.9 1.1 101 4.9 1.8 162 6.2 0.5 73 3.1 45 40

15821 15.88 3.18 0.40 0.25 90.9 5.1 5.1 2.0 186 4.7 2.0 186 4.7 3.1 279 5.9 0.9 120 3.1 45 306

15297 19.04 1.60 0.40 0.16 58.4 5.4 5.4 2.0 149 5.9 2.0 149 5.9 3.2 241 7.5 0.8 109 3.8 45 50

15823 19.05 3.18 0.40 0.30 111.0 5.9 5.9 3.6 275 5.7 3.6 275 5.7 5.7 422 7.2 1.5 182 3.7 45 374

15145 19.06 3.18 0.76 0.30 111.1 5.9 5.9 3.6 275 5.7 3.6 275 5.7 5.7 423 7.2 1.5 183 3.7 45 375

150019 20.00 1.25 0.40 0.13 48.4 5.5 5.5 1.9 131 6.3 1.9 131 6.3 3.0 215 7.9 0.8 99 4.0 45 25

15578 20.00 1.50 0.40 0.16 57.8 5.6 5.6 2.2 155 6.2 2.2 155 6.2 3.6 253 7.9 0.9 115 4.0 45 43

15556 20.00 2.00 0.40 0.21 76.0 5.7 5.7 2.9 202 6.2 2.9 202 6.2 4.6 324 7.8 1.2 145 3.9 45 101

15859 20.00 3.00 0.40 0.30 111.0 6.1 6.1 4.0 290 6.0 4.0 290 6.0 6.4 451 7.6 1.7 196 3.9 45 333

15147 22.22 1.60 0.64 0.19 68.5 6.1 6.1 3.3 205 6.9 3.3 205 6.9 5.2 334 8.8 1.3 153 4.4 45 58

15148 22.22 3.18 0.64 0.36 131.2 6.7 6.7 5.9 381 6.7 5.9 381 6.7 9.4 596 8.4 2.5 259 4.3 45 442

150020 25.00 1.25 0.40 0.17 60.9 6.7 6.7 3.8 207 7.9 3.8 207 7.9 6.0 342 10.0 1.5 160 5.0 45 32

150003 25.00 1.50 0.40 0.20 72.8 6.8 6.8 4.5 246 7.8 4.5 246 7.8 7.1 404 9.9 1.8 187 5.0 45 55

15359 25.00 1.60 0.30 0.21 77.4 6.8 6.8 4.7 261 7.8 4.7 261 7.8 7.6 428 9.9 1.9 197 5.0 45 66

15526 25.00 2.00 0.50 0.26 96.0 7.0 7.0 5.8 321 7.8 5.8 321 7.8 9.2 522 9.8 2.3 237 4.9 45 128

15871 25.00 3.00 0.40 0.38 141.0 7.4 7.4 8.2 465 7.6 8.2 465 7.6 13.0 737 9.6 3.4 325 4.9 45 423

15940 25.00 4.00 0.40 0.50 184.0 7.7 7.7 10.4 599 7.5 10.4 599 7.5 16.3 925 9.4 4.4 400 4.9 45 981

15192 25.40 1.52 0.25 0.20 74.9 6.9 6.9 4.7 257 8.0 4.7 257 8.0 7.6 422 10.1 1.9 196 5.1 45 58

15155 25.40 2.38 0.64 0.31 115.2 7.2 7.2 7.1 390 7.8 7.1 390 7.8 11.3 628 9.9 2.9 282 5.0 45 218

15824 25.40 3.18 0.40 0.41 151.4 7.5 7.5 9.1 506 7.7 9.1 506 7.7 14.4 800 9.7 3.7 352 5.0 45 510

15193 25.40 4.75 0.63 0.59 218.7 8.1 8.1 12.4 718 7.5 12.4 718 7.5 19.5 1088 9.4 5.3 468 4.9 45 1645

15825 25.40 4.78 0.40 0.60 220.0 8.1 8.1 12.5 722 7.5 12.5 722 7.5 19.6 1092 9.4 5.4 470 4.9 45 1675

15158 25.40 6.36 0.40 0.77 282.6 8.6 8.6 15.4 916 7.4 15.4 916 7.4 23.7 1321 9.2 7.0 574 5.0 45 3811

15150 25.40 10.14 0.56 0.15 412.3 9.8 9.8 20.8 1336 7.1 20.8 1336 7.1 30.2 1680 8.6 11.4 822 5.3 45 14131

15527 30.00 2.00 0.50 0.31 116.0 8.2 8.2 10.2 469 9.4 10.2 469 9.4 16.3 767 11.8 4.1 353 6.0 45 155

Torsion

ConstantProfile

Number

Dimensions Centroid X-X Axis Y-Y Axis Principal Axis

A

mm

T

mm

R1

mm

Mass

kg/m

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

August 2007

Prev

Next

Pg 5

Hulam


atalogue4

8

T

o90

A

A

T

y 2

Cyy

Cx

1

x

21

x

15860 30.00 3.00 0.40 0.46 171.0 8.6 8.6 14.6 681 9.2 14.6 681 9.2 23.2 1094 11.7 5.9 489 5.9 45 513

15529 30.00 3.00 0.76 0.46 171.0 8.6 8.6 14.6 681 9.2 14.6 681 9.2 23.2 1094 11.7 5.9 489 5.9 45 513

15861 30.00 4.00 0.40 0.61 224.0 9.0 9.0 18.6 882 9.1 18.6 882 9.1 29.4 1387 11.5 7.7 607 5.9 45 1195

15901 30.00 5.00 0.40 0.75 275.0 9.3 9.3 22.2 1072 9.0 22.2 1072 9.0 34.9 1647 11.3 9.4 712 5.8 45 2292

15708 31.75 1.60 0.20 0.27 99.0 8.5 8.5 9.9 426 10.0 9.9 426 10.0 15.8 705 12.6 4.0 330 6.3 45 85

15585 31.75 2.60 0.40 0.43 158.3 8.9 8.9 15.4 673 9.9 15.4 673 9.9 24.5 1092 12.4 6.2 495 6.3 45 357

15826 31.75 3.18 0.40 0.52 191.8 9.1 9.1 18.3 809 9.8 18.3 809 9.8 29.2 1299 12.3 7.5 580 6.2 45 647

15555 31.75 4.76 0.40 0.76 279.6 9.7 9.7 25.6 1159 9.6 25.6 1159 9.6 40.5 1802 12.0 10.7 783 6.2 45 2112

15163 31.76 6.36 0.40 0.99 363.5 10.2 10.2 32.0 1487 9.4 32.0 1487 9.4 50.1 2231 11.7 13.9 960 6.2 45 4902

15713 35.00 1.80 0.40 0.33 122.8 9.4 9.4 14.9 582 11.0 14.9 582 11.0 23.8 962 13.9 6.0 450 7.0 45 133

15540 35.00 3.00 0.50 0.54 201.0 9.9 9.9 23.6 940 10.8 23.6 940 10.8 37.7 1522 13.7 9.6 688 6.9 45 603

15970 38.00 3.00 0.40 0.59 219.0 10.6 10.6 30.5 1115 11.8 30.5 1115 11.8 48.7 1813 14.9 12.4 824 7.5 45 657

15972 38.00 6.00 0.40 1.14 420.0 11.7 11.7 54.7 2079 11.4 54.7 2079 11.4 86.4 3215 14.3 23.0 1392 7.4 45 5040

150007 38.10 1.60 0.40 0.32 119.4 10.1 10.1 17.3 619 12.0 17.3 619 12.0 27.7 1028 15.2 7.0 486 7.6 45 102

15291 38.10 2.04 0.76 0.41 151.3 10.3 10.3 21.7 781 12.0 21.7 781 12.0 34.7 1288 15.1 8.7 600 7.6 45 210

15827 38.10 3.18 0.40 0.63 232.2 10.7 10.7 32.4 1183 11.8 32.4 1183 11.8 51.7 1918 14.9 13.1 868 7.5 45 783

15165 38.10 3.18 0.76 0.63 232.2 10.7 10.7 32.4 1183 11.8 32.4 1183 11.8 51.7 1918 14.9 13.1 868 7.5 45 783

15828 38.10 4.78 0.40 0.93 341.4 11.3 11.3 45.9 1712 11.6 45.9 1712 11.6 72.9 2705 14.6 19.0 1188 7.5 45 2600

15170 38.10 6.35 0.40 1.20 443.5 11.8 11.8 57.7 2195 11.4 57.7 2195 11.4 90.9 3375 14.3 24.4 1458 7.4 45 5962

150004 40.00 1.50 0.40 0.32 117.8 10.6 10.6 18.9 642 12.7 18.9 642 12.7 30.2 1069 16.0 7.6 508 8.0 45 88

15372 40.00 1.60 0.40 0.34 125.4 10.6 10.6 20.1 684 12.7 20.1 684 12.7 32.1 1136 16.0 8.1 538 8.0 45 107

15862 40.00 2.00 0.40 0.42 156.0 10.7 10.7 24.8 846 12.6 24.8 846 12.6 39.6 1399 15.9 10.0 655 8.0 45 208

15879 40.00 3.00 0.40 0.63 231.0 11.1 11.1 35.8 1240 12.5 35.8 1240 12.5 57.2 2021 15.7 14.5 922 7.9 45 693

15557 40.00 4.00 0.40 0.82 304.0 11.5 11.5 46.1 1615 12.3 46.1 1615 12.3 73.4 2594 15.5 18.8 1158 7.9 45 1621

15532 40.00 5.00 0.76 1.02 375.0 11.8 11.8 55.6 1974 12.2 55.6 1974 12.2 88.3 3121 15.3 22.9 1371 7.8 45 3125

15373 40.00 6.00 0.40 1.20 444.0 12.2 12.2 64.5 2319 12.1 64.5 2319 12.1 102.0 3605 15.2 27.0 1566 7.8 45 5328

150014 44.45 4.76 0.40 1.09 400.5 12.9 12.9 74.5 2359 13.6 74.5 2359 13.6 118.5 3771 17.2 30.5 1675 8.7 45 3025

15172 44.46 3.18 0.40 0.74 272.7 12.3 12.3 52.4 1629 13.9 52.4 1629 13.9 83.6 2660 17.5 21.2 1218 8.8 45 919

15913 45.00 4.00 0.40 0.93 344.0 12.7 12.7 66.7 2065 13.9 66.7 2065 13.9 106.2 3339 17.6 27.1 1504 8.9 45 1835

15890 45.00 5.00 0.40 1.15 425.0 13.1 13.1 80.7 2530 13.8 80.7 2530 13.8 128.4 4035 17.4 33.1 1788 8.8 45 3542

15563 50.00 2.00 0.40 0.53 196.0 13.2 13.2 49.1 1335 15.8 49.1 1335 15.8 78.5 2219 20.0 19.7 1051 10.0 45 261

15736 50.00 2.00 0.80 0.53 196.0 13.2 13.2 49.1 1335 15.8 49.1 1335 15.8 78.5 2219 20.0 19.7 1051 10.0 45 261

Torsion

ConstantProfile

Number


A

mm

T

mm

R1

mm

Mass

kg/m

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

Angle Type 1 Equal angle, no radius

(continued)

August 2007

Prev

Next

Pg 5

T

o90

A

A

T

y 2

Cyy

Cx

1

x

21

x

15733 50.00 3.00 0.50 0.79 291.0 13.6 13.6 71.5 1965 15.7 71.5 1965 15.7 114.2 3230 19.8 28.8 1496 9.9 45 873

15530 50.00 3.00 0.76 0.79 291.0 13.6 13.6 71.5 1965 15.7 71.5 1965 15.7 114.2 3230 19.8 28.8 1496 9.9 45 873

15906 50.00 4.00 0.40 1.04 384.0 14.0 14.0 92.6 2571 15.5 92.6 2571 15.5 147.7 4178 19.6 37.5 1897 9.9 45 2048

15854 50.00 6.00 0.40 1.53 564.0 14.7 14.7 131.3 3719 15.3 131.3 3719 15.3 208.5 5897 19.2 54.0 2598 9.8 45 6768

15908 50.00 8.00 0.40 1.99 736.0 15.4 15.4 165.7 4790 15.0 165.7 4790 15.0 261.5 7397 18.9 69.8 3202 9.7 45 15701

15993 50.80 1.59 0.40 0.43 159.0 13.3 13.3 41.4 1105 16.1 41.4 1105 16.1 66.3 1845 20.4 16.6 884 10.2 45 134

15829 50.80 3.18 0.40 0.85 313.0 13.9 13.9 79.2 2145 15.9 79.2 2145 15.9 126.5 3520 20.1 31.9 1626 10.1 45 1055

15830 50.80 4.78 0.40 1.25 462.8 14.5 14.5 113.7 3130 15.7 113.7 3130 15.7 181.2 5045 19.8 46.3 2263 10.0 45 3525

15831 50.80 6.35 0.40 1.64 604.8 15.0 15.0 144.7 4044 15.5 144.7 4044 15.5 229.7 6393 19.5 59.7 2809 9.9 45 8130

15174 50.80 9.52 0.76 2.37 876.6 16.1 16.1 199.3 5752 15.1 199.3 5752 15.1 313.0 8713 18.9 85.7 3752 9.9 45 26482

150000 60.00 2.00 0.40 0.64 236.0 15.7 15.7 85.6 1935 19.0 85.6 1935 19.0 137.0 3228 24.1 34.3 1542 12.1 45 315

15575 60.00 2.50 0.40 0.80 293.8 15.9 15.9 105.7 2400 19.0 105.7 2400 19.0 169.1 3985 24.0 42.4 1884 12.0 45 612

15880 60.00 3.00 0.40 0.95 351.0 16.1 16.1 125.4 2856 18.9 125.4 2856 18.9 200.3 4722 23.9 50.4 2211 12.0 45 1053

15572 60.00 4.00 0.40 1.26 464.0 16.5 16.5 163.1 3749 18.8 163.1 3749 18.8 260.5 6139 23.7 65.8 2823 11.9 45 2475

15881 60.00 5.00 0.40 1.56 575.0 16.8 16.8 199.1 4613 18.6 199.1 4613 18.6 317.4 7482 23.5 80.7 3387 11.8 45 4792

15872 60.00 6.00 0.40 1.85 684.0 17.2 17.2 233.3 5452 18.5 233.3 5452 18.5 371.4 8754 23.3 95.2 3910 11.8 45 8208

15506 60.00 8.00 0.50 2.43 896.0 17.9 17.9 296.9 7056 18.2 296.9 7056 18.2 470.7 11094 22.9 123.0 4853 11.7 45 19115

15207 63.50 3.18 0.64 1.07 393.7 17.1 17.1 157.5 3391 20.0 157.5 3391 20.0 251.7 5606 25.3 63.3 2624 12.7 45 1327

15176 63.50 6.36 0.40 2.08 767.3 18.2 18.2 293.1 6472 19.5 293.1 6472 19.5 466.6 10391 24.7 119.6 4640 12.5 45 10345

15363 64.00 8.00 0.76 2.60 960.0 18.9 18.9 364.5 8087 19.5 364.5 8087 19.5 578.6 12784 24.5 150.4 5617 12.5 45 20480

15939 70.00 5.00 0.40 1.83 675.0 19.4 19.4 321.6 6350 21.8 321.6 6350 21.8 513.3 10370 27.6 129.9 4747 13.9 45 5625

15907 70.00 6.00 0.40 2.18 804.0 19.7 19.7 378.1 7519 21.7 378.1 7519 21.7 602.7 12177 27.4 153.4 5501 13.8 45 9648

15485 75.00 3.00 0.50 1.19 441.0 19.9 19.9 248.5 4506 23.7 248.5 4506 23.7 397.2 7490 30.0 99.7 3548 15.0 45 1323

15980 75.00 6.00 0.40 2.34 864.0 21.0 21.0 468.8 8677 23.3 468.8 8677 23.3 747.8 14101 29.4 189.9 6403 14.8 45 10368

15735 76.00 2.00 0.50 0.81 300.0 19.7 19.7 175.9 3126 24.2 175.9 3126 24.2 281.3 5234 30.6 70.4 2522 15.3 45 400

15420 76.00 4.00 0.64 1.60 592.0 20.5 20.5 338.4 6095 23.9 338.4 6095 23.9 540.7 10061 30.2 136.1 4696 15.2 45 3157

15832 76.20 3.18 0.40 1.29 474.5 20.2 20.2 275.5 4923 24.1 275.5 4923 24.1 440.4 8174 30.5 110.6 3864 15.3 45 1600

15833 76.20 4.78 0.40 1.91 705.6 20.8 20.8 401.6 7252 23.9 401.6 7252 23.9 641.4 11903 30.1 161.9 5496 15.1 45 5374

15834 76.20 6.35 0.40 2.51 927.4 21.4 21.4 517.9 9450 23.6 517.9 9450 23.6 825.8 15327 29.8 210.0 6939 15.0 45 12465

15209 76.20 6.35 0.64 2.52 927.4 21.4 21.4 517.9 9450 23.6 517.9 9450 23.6 825.8 15327 29.8 210.0 6939 15.0 45 12465

15210 76.20 9.52 0.40 3.69 1360.2 22.5 22.5 732.1 13644 23.2 732.1 13644 23.2 1162.2 21569 29.2 302.1 9476 14.9 45 41092

15178 76.20 12.70 0.76 4.81 1774.2 23.7 23.7 922.5 17561 22.8 922.5 17561 22.8 1454.6 26997 28.6 390.4 11664 14.8 45 95386

Torsion

ConstantProfile

Number


A

mm

T

mm

R1

mm

Mass

kg/m

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg


(continued)

Hulam


atalogue4

9August 2007

Prev

Next

Pg 5

50


(continued)

T

o90

A

A

T

y 2

Cyy

Cx

1

x

21

x

15995 88.90 6.35 0.40 2.95 1088.7 24.6 24.6 836.6 13006 27.7 836.6 13006 27.7 1335.3 21241 35.0 337.9 9723 17.6 45 14633

15922 100.00 3.00 0.40 1.60 591.0 26.1 26.1 597.7 8090 31.8 597.7 8090 31.8 955.9 13518 40.2 239.5 6483 20.1 45 1773

15905 100.00 10.00 0.40 5.15 1900.0 28.7 28.7 1800.0 25240 30.8 1800.0 25240 30.8 2865.8 40529 38.8 734.3 18100 19.7 45 63333

15984 101.60 6.35 0.40 3.39 1250.0 27.8 27.8 1265.1 17131 31.8 1265.1 17131 31.8 2020.3 28122 40.2 509.8 12988 20.2 45 16801

15994 101.60 9.53 0.40 5.00 1845.7 28.9 28.9 1815.0 24971 31.4 1815.0 24971 31.4 2891.5 40248 39.6 738.6 18061 20.0 45 55875

15181 101.60 12.70 0.78 6.56 2419.4 30.1 30.1 2314.9 32356 30.9 2314.9 32356 30.9 3674.5 51148 39.0 955.2 22471 19.9 45 130072

15947 120.00 8.00 0.40 5.03 1856.0 33.0 33.0 2610.2 29990 37.5 2610.2 29990 37.5 4167.3 49113 47.4 1053.0 22586 23.8 45 39595

15856 120.00 12.00 0.40 7.41 2736.0 34.4 34.4 3732.6 43616 36.9 3732.6 43616 36.9 5942.6 70034 46.6 1522.5 31278 23.6 45 131328

150005 152.40 12.70 0.40 10.05 3709.7 42.8 42.8 8286.3 75600 47.3 8286.3 75600 47.3 13213.2 122613 59.7 3359.4 55509 30.1 45 199444

Torsion

ConstantProfile

Number


A

mm

T

mm

R1

mm

Mass

kg/m

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

Type 2 Equal angle, with all radii

greater than 0.80

51

Angle

y 2

Cyy

Cx

1

x

2

x

1

R1 R2

R2

T

o90A

A

T

15810 44.45 6.35 4.76 3.18 1.42 524.7 13.3 13.3 92.6 2972 13.3 92.6 2972 13.3 135.7 4318 16.1 49.6 2639 9.7 45 7046

15349 50.00 3.00 3.00 1.50 0.79 292.0 13.5 13.5 71.0 1945 15.6 71.0 1945 15.6 109.8 3107 19.4 32.2 1684 10.5 45 873

15990 50.00 4.70 1.00 1.00 1.21 447.7 14.2 14.2 106.4 2973 15.4 106.4 2973 15.4 165.7 4687 19.2 47.1 2341 10.3 45 3298

15949 50.00 5.00 1.20 1.20 1.26 474.7 14.3 14.3 112.1 3142 15.4 112.1 3142 15.4 173.7 4914 19.1 50.5 2493 10.3 45 3958

15545 50.80 3.18 6.35 3.18 0.86 317.3 13.5 13.5 76.8 2057 15.6 76.8 2057 15.6 115.4 3213 19.1 38.2 2005 11.0 45 1055

15546 50.80 4.76 6.35 3.18 1.26 465.3 14.2 14.2 111.0 3030 15.4 111.0 3030 15.4 165.6 4611 18.9 56.3 2806 11.0 45 3481

15547 50.80 6.35 6.35 3.18 1.65 609.2 14.8 14.8 142.3 3957 15.3 142.3 3957 15.3 211.1 5876 18.6 73.5 3505 11.0 45 8130

15811 63.50 6.35 6.35 3.18 2.09 770.4 18.0 18.0 289.0 6352 19.4 289.0 6352 19.4 435.9 9709 23.8 142.0 5577 13.6 45 10297

15543 76.20 6.35 7.93 6.35 2.50 923.6 20.9 20.9 493.5 8917 23.1 493.5 8917 23.1 726.8 13488 28.1 260.2 8822 16.8 45 12465

15964 76.20 6.35 7.95 3.18 2.54 936.6 21.1 21.1 513.4 9321 23.4 513.4 9321 23.4 782.5 14523 28.9 244.3 8182 16.2 45 12465

15544 76.20 9.53 7.93 6.35 3.68 1357.7 22.2 22.2 709.4 13135 22.9 709.4 13135 22.9 1032.4 19160 27.6 386.4 12311 16.9 45 41219

15135 101.60 6.36 9.52 6.36 3.40 1254.0 27.1 27.1 1224.1 16435 31.2 1224.1 16435 31.2 1841.9 25638 38.3 606.4 15812 22.0 45 16880

15813 101.60 9.53 9.53 6.35 5.01 1847.9 28.5 28.5 1773.4 24259 31.0 1773.4 24259 31.0 2648.7 36868 37.9 898.1 22286 22.0 45 55875

15851 101.60 12.70 9.54 6.35 6.56 2421.6 29.8 29.8 2274.1 31651 30.6 2274.1 31651 30.6 3374.4 46970 37.3 1173.9 27900 22.0 45 130072

Torsion

ConstantProfile

Number


A

mm

T

mm

R2

mm

Mass

kg/m

R1

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm4

Zx

mm3

r

mm

Iy

x103mm4

Zy

mm3

r

mm

I1

x103mm4

Z1

mm3

r

mm

J

mm4

I2

x103mm4

Z2

mm3

r

mm

Angle

deg

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

Type 3 Equal angle, with outside corner

radius (R) less than or equal to 0.802

52

Angle

y 2

Cyy

Cx

1

x

2

x

1

R1 R2

R2

T

o90A

A

T

15096 25.40 3.18 4.58 0.64 0.42 155.8 7.4 7.4 9.1 505 7.6 9.1 505 7.6 14.3 798 9.6 3.8 365 5.0 45 510

15966 38.10 3.18 2.38 0.38 0.63 233.4 10.7 10.7 32.4 1183 11.8 32.4 1183 11.8 51.6 1917 14.9 13.2 879 7.5 45 783

15102 38.10 3.18 5.34 0.64 0.65 238.1 10.5 10.5 32.6 1182 11.7 32.6 1182 11.7 51.6 1915 14.7 13.6 913 7.6 45 783

15103 38.10 4.74 5.34 0.64 0.94 344.7 11.2 11.2 45.7 1697 11.5 45.7 1697 11.5 72.3 2684 14.5 19.1 1212 7.5 45 2537

15104 38.10 6.36 5.34 0.64 1.22 450.1 11.8 11.8 57.8 2195 11.3 57.8 2195 11.3 90.9 3376 14.2 24.6 1479 7.4 45 5989

15110 50.80 3.18 6.10 0.64 0.87 320.8 13.6 13.6 79.8 2146 15.8 79.8 2146 15.8 126.3 3515 19.8 33.2 1723 10.2 45 1055

15111 50.80 4.74 6.10 0.64 1.27 466.9 14.3 14.3 113.4 3106 15.6 113.4 3106 15.6 179.7 5004 19.6 47.0 2324 10.0 45 3438

15112 50.80 6.36 6.10 0.64 1.66 613.5 14.9 14.9 145.2 4048 15.4 145.2 4048 15.4 229.8 6397 19.4 60.6 2869 9.9 45 8167

15113 50.80 7.92 6.10 0.64 2.04 749.8 15.5 15.5 173.2 4908 15.2 173.2 4908 15.2 273.1 7603 19.1 73.3 3338 9.9 45 15513

15118 63.50 6.36 6.86 0.64 2.11 777.2 18.1 18.1 294.0 6472 19.4 294.0 6472 19.4 466.3 10386 24.5 121.6 4756 12.5 45 10345

15119 63.50 7.92 6.86 0.64 2.58 953.0 18.7 18.7 353.3 7882 19.3 353.3 7882 19.3 559.5 12460 24.2 147.1 5571 12.4 45 19719

15121 76.20 6.36 7.62 0.76 2.57 941.0 21.2 21.2 520.5 9466 23.5 520.5 9466 23.5 826.4 15338 29.6 214.5 7148 15.1 45 12523

15122 76.20 7.96 7.62 0.64 3.15 1162.0 21.8 21.8 631.6 11620 23.3 631.6 11620 23.3 1002.1 18599 29.4 261.1 8452 15.0 45 24283

15123 76.20 9.52 7.62 0.64 3.72 1372.5 22.4 22.4 733.5 13643 23.1 733.5 13643 23.1 1161.8 21563 29.1 305.2 9618 14.9 45 41092

15125 88.90 6.36 8.38 0.64 2.99 1105.3 24.4 24.4 841.5 13036 27.6 841.5 13036 27.6 1336.6 21263 34.8 346.3 10054 17.7 45 14702

15234 88.90 7.95 8.38 0.64 3.70 1365.2 25.0 25.0 1023.9 16020 27.4 1023.9 16020 27.4 1626.2 25869 34.5 421.6 11930 17.6 45 28448

15127 88.90 9.52 8.38 0.64 4.38 1616.9 25.6 25.6 1194.8 18872 27.2 1194.8 18872 27.2 1895.9 30159 34.2 493.7 13641 17.5 45 48397

15128 88.90 12.70 8.38 0.64 5.72 2111.7 26.8 26.8 1515.0 24387 26.8 1515.0 24387 26.8 2395.1 38101 33.7 634.9 16768 17.3 45 112729

15479 100.00 4.00 4.50 0.50 2.14 788.2 26.4 26.4 786.9 10687 31.6 786.9 10687 31.6 1255.0 17748 39.9 318.9 8552 20.1 45 4181

15130 101.60 9.52 9.14 0.64 5.04 1861.6 28.7 28.7 1818.3 24957 31.3 1818.3 24957 31.3 2888.3 40203 39.4 748.4 18413 20.1 45 55702

15132 127.00 9.52 10.66 0.76 6.37 2351.6 35.0 35.0 3650.4 39690 39.4 3650.4 39690 39.4 5803.7 64627 49.7 1497.1 30222 25.2 45 70313

15294 127.00 12.70 6.36 0.76 8.33 3072.9 36.4 36.4 4686.0 51701 39.1 4686.0 51701 39.1 7453.7 83001 49.3 1918.2 37301 25.0 45 164758

15286 152.40 9.52 12.18 0.76 7.70 2842.7 41.3 41.3 6427.3 57851 47.6 6427.3 57851 47.6 10220.9 94846 60.0 2633.6 45092 30.4 45 84923

15287 152.40 12.70 12.18 0.76 10.14 3741.3 42.6 42.6 8308.7 75642 47.1 8308.7 75642 47.1 13211.2 122595 59.4 3406.3 56596 30.2 45 199444

Torsion

ConstantProfile

Number


A

mm

T

mm

R2

mm

Mass

kg/m

R1

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm4

Zx

mm3

r

mm

Iy

x103mm4

Zy

mm3

r

mm

I1

x103mm4

Z1

mm3

r

mm

J

mm4

I2

x103mm4

Z2

mm3

r

mm

Angle

deg

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

53

y 2

Cyy

Cx1

x

2

x

1

T

o90

A

B

T

15561 15.00 10.00 2.00 0.40 0.12 46.0 2.7 5.2 1.0 104 4.7 0.4 49 2.8 1.2 106 5.0 0.2 36 2.1 23.0 61

15408 15.88 9.52 1.60 0.64 0.10 38.1 2.4 5.6 1.0 94 5.0 0.3 37 2.6 1.1 96 5.3 0.2 28 2.1 19.6 32

15000 19.06 6.36 1.60 0.78 0.10 38.1 1.4 7.8 1.4 124 6.0 0.1 17 1.5 1.4 124 6.1 0.1 15 1.3 7.2 33

15441 19.06 9.54 2.38 0.76 0.17 62.4 2.5 7.3 2.3 191 6.0 0.4 53 2.5 2.4 191 6.2 0.3 44 2.0 13.8 118

15038 19.06 12.70 1.58 0.76 0.13 47.7 3.1 6.3 1.8 138 6.1 0.6 66 3.6 2.0 144 6.5 0.4 49 2.8 23.7 40

15039 19.06 12.70 3.18 0.64 0.25 90.9 3.7 6.9 3.2 259 5.9 1.1 122 3.5 3.6 261 6.3 0.7 90 2.7 22.4 306

15322 20.00 9.00 3.00 0.50 0.21 78.0 2.5 8.0 3.0 254 6.2 0.4 59 2.2 3.1 252 6.3 0.3 51 1.9 10.9 234

15909 20.00 10.00 2.00 0.40 0.15 56.0 2.4 7.4 2.3 181 6.4 0.4 51 2.6 2.4 182 6.5 0.3 41 2.1 14.3 75

15885 20.00 15.00 2.00 0.40 0.18 66.0 4.0 6.5 2.6 194 6.3 1.3 115 4.4 3.2 204 7.0 0.7 79 3.2 28.7 88

15040 20.66 6.36 1.60 0.76 0.11 40.7 1.4 8.5 1.7 144 6.5 0.1 17 1.4 1.8 144 6.6 0.1 15 1.2 6.4 35

15376 22.00 8.00 3.00 0.30 0.22 81.0 2.2 9.2 3.8 298 6.9 0.3 48 1.8 3.9 296 6.9 0.2 44 1.6 7.4 243

15041 22.22 7.96 3.18 0.64 0.23 85.9 2.3 9.4 4.1 320 6.9 0.3 51 1.8 4.2 317 7.0 0.2 47 1.6 7.0 289

15042 22.22 9.52 1.60 0.76 0.13 48.2 2.1 8.4 2.5 178 7.1 0.3 38 2.4 2.6 180 7.3 0.2 32 2.0 11.4 41

15043 22.22 9.52 3.18 0.76 0.25 90.8 2.6 9.0 4.4 331 6.9 0.5 70 2.3 4.5 329 7.0 0.4 61 2.0 10.0 306

150027 25.00 10.30 1.30 0.50 0.12 44.2 2.0 9.4 2.9 186 8.1 0.3 38 2.7 3.0 188 8.2 0.2 31 2.2 11.0 25

15347 25.00 12.50 1.50 0.30 0.15 54.0 2.7 8.9 3.5 220 8.1 0.6 63 3.4 3.8 224 8.4 0.4 50 2.7 15.0 41

15928 25.00 15.00 2.00 0.40 0.21 76.0 3.6 8.6 4.9 297 8.0 1.3 118 4.2 5.4 306 8.4 0.8 89 3.3 19.9 101

150001 25.00 20.00 1.60 0.40 0.19 69.4 5.0 7.5 4.4 253 8.0 2.5 169 6.0 5.7 275 9.0 1.3 114 4.3 32.3 59

15985 25.00 20.00 3.00 0.40 0.34 126.0 5.5 8.0 7.6 450 7.8 4.3 299 5.9 9.7 476 8.8 2.2 199 4.2 31.8 378

15241 25.40 12.70 1.60 0.64 0.16 58.4 2.7 9.1 3.9 242 8.2 0.7 69 3.4 4.2 246 8.5 0.4 55 2.7 14.9 50

15050 25.40 12.70 3.18 0.20 0.30 111.0 3.3 9.7 7.1 453 8.0 1.2 126 3.3 7.5 453 8.2 0.8 103 2.7 13.8 374

15051 25.40 15.88 1.60 0.64 0.17 63.5 3.7 8.4 4.3 251 8.2 1.3 108 4.6 4.8 261 8.7 0.8 81 3.5 21.6 54

15264 25.40 15.88 3.18 0.64 0.33 121.2 4.2 9.0 7.7 471 8.0 2.3 198 4.4 8.6 479 8.4 1.4 150 3.4 20.6 408

15836 25.40 19.05 3.18 0.40 0.36 131.2 5.3 8.4 8.2 485 7.9 3.9 286 5.5 10.0 505 8.7 2.2 198 4.1 28.4 442

15412 28.00 22.00 2.48 0.76 0.32 117.8 5.8 8.8 9.2 479 8.8 5.0 309 6.5 11.6 512 9.9 2.6 209 4.7 31.2 242

15731 30.00 10.00 2.00 0.25 0.21 76.0 2.1 12.1 7.0 390 9.6 0.4 53 2.4 7.1 390 9.7 0.3 46 2.0 7.5 101

15567 30.00 15.00 2.00 0.40 0.23 86.0 3.3 10.8 8.1 420 9.7 1.4 120 4.0 8.6 427 10.0 0.9 96 3.2 14.9 115

15558 30.00 15.00 3.00 0.40 0.34 126.0 3.6 11.1 11.5 610 9.6 1.9 171 3.9 12.2 615 9.8 1.3 138 3.2 14.3 378

15875 30.00 20.00 2.00 0.40 0.26 96.0 4.8 9.8 8.9 441 9.6 3.2 213 5.8 10.3 462 10.4 1.8 156 4.4 24.0 128

15559 30.00 20.00 3.00 0.40 0.38 141.0 5.1 10.1 12.7 641 9.5 4.6 306 5.7 14.7 663 10.2 2.6 224 4.3 23.5 423

15926 30.00 20.00 4.00 0.40 0.50 184.0 5.5 10.5 16.2 829 9.4 5.7 392 5.6 18.5 847 10.0 3.4 289 4.3 23.0 981

15255 31.76 12.70 2.64 0.64 0.30 110.4 2.8 12.4 11.4 587 10.1 1.1 110 3.1 11.7 588 10.3 0.8 93 2.6 10.0 256

Torsion

ConstantProfile

Number


A

mm

B

mm

R1

mm

Mass

kg/m

T

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

Angle Type 4 Unequal angle, no radius

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

54

y 2

Cyy

Cx1

x

2

x

1

T

o90

A

B

T

15411 31.76 15.88 2.76 0.76 0.33 123.9 3.7 11.6 12.8 637 10.2 2.2 180 4.2 13.6 644 10.5 1.4 144 3.4 14.5 315

15057 31.76 19.06 3.18 0.40 0.41 151.5 4.8 11.1 15.4 748 10.1 4.2 294 5.3 17.1 764 10.6 2.6 224 4.1 19.6 511

15463 31.76 25.40 2.00 0.76 0.30 110.3 6.4 9.6 11.3 510 10.1 6.5 342 7.7 14.5 555 11.5 3.3 231 5.5 32.3 147

15058 31.76 25.40 3.18 0.40 0.47 171.7 6.8 10.0 17.1 784 10.0 9.7 522 7.5 21.8 837 11.3 5.0 348 5.4 32.0 579

15059 32.94 17.86 1.60 0.64 0.21 78.7 3.8 11.3 9.1 418 10.7 2.0 140 5.0 9.8 430 11.2 1.2 110 3.9 17.3 67

15882 35.00 20.00 3.00 0.40 0.42 156.0 4.8 12.3 19.6 861 11.2 4.7 311 5.5 21.4 880 11.7 2.9 241 4.3 18.3 468

15061 38.10 12.70 3.18 0.64 0.41 151.4 2.9 15.6 22.1 982 12.1 1.3 133 2.9 22.5 981 12.2 1.0 117 2.5 7.2 510

15837 38.10 19.05 3.18 0.40 0.47 171.6 4.4 13.9 25.6 1059 12.2 4.4 300 5.1 27.2 1072 12.6 2.9 240 4.1 14.6 579

15838 38.10 25.40 3.18 0.40 0.52 191.8 6.3 12.6 28.4 1113 12.2 10.2 534 7.3 32.7 1158 13.1 5.9 391 5.5 23.7 647

15845 38.10 25.40 4.75 0.50 0.76 279.1 6.8 13.2 39.9 1601 12.0 14.1 759 7.1 45.6 1640 12.8 8.3 557 5.5 23.1 2099

15581 40.00 10.00 2.00 0.40 0.26 96.0 1.8 16.8 15.5 669 12.7 0.4 55 2.2 15.6 669 12.8 0.3 49 1.9 4.8 128

150002 40.00 20.00 1.60 0.40 0.25 93.4 4.0 14.0 16.0 613 13.1 2.9 178 5.5 17.0 628 13.5 1.8 142 4.4 15.3 80

15876 40.00 20.00 2.00 0.40 0.31 116.0 4.1 14.1 19.7 759 13.0 3.5 219 5.5 20.9 775 13.4 2.2 175 4.4 15.1 155

15891 40.00 20.00 2.50 0.40 0.39 143.8 4.3 14.3 24.1 937 12.9 4.2 268 5.4 25.6 954 13.3 2.7 214 4.3 14.9 299

15886 40.00 20.00 3.00 0.40 0.46 171.0 4.5 14.5 28.3 1110 12.9 4.9 316 5.4 30.1 1126 13.3 3.2 253 4.3 14.7 513

15576 40.00 20.00 4.00 0.40 0.61 224.0 4.9 14.9 36.3 1445 12.7 6.2 406 5.2 38.4 1457 13.1 4.1 327 4.3 14.3 1195

15950 40.00 25.00 2.00 0.40 0.34 126.0 5.6 13.1 21.2 788 13.0 6.6 340 7.2 24.0 823 13.8 3.9 256 5.5 21.8 168

15986 40.00 25.00 3.00 0.40 0.50 186.0 5.9 13.4 30.7 1154 12.8 9.4 493 7.1 34.5 1195 13.6 5.5 370 5.5 21.4 558

15931 40.00 30.00 2.00 0.40 0.37 136.0 7.2 12.2 22.6 812 12.9 11.1 486 9.0 27.8 874 14.3 5.8 341 6.6 29.3 181

15562 40.00 30.00 3.00 0.40 0.54 201.0 7.5 12.5 32.6 1189 12.7 15.9 708 8.9 40.1 1267 14.1 8.4 492 6.5 29.0 603

15258 44.45 19.05 3.17 0.63 0.52 191.2 4.1 16.8 39.1 1414 14.3 4.5 304 4.9 40.6 1425 14.6 3.1 251 4.0 11.4 641

15064 44.46 22.22 2.04 0.64 0.36 131.9 4.5 15.6 27.7 960 14.5 4.9 278 6.1 29.5 982 15.0 3.1 222 4.9 15.2 183

15065 44.46 22.22 3.18 0.64 0.55 201.9 4.9 16.0 41.5 1459 14.3 7.2 415 6.0 44.0 1481 14.8 4.6 332 4.8 14.8 681

15067 44.46 38.10 3.18 0.76 0.68 252.4 10.0 13.2 49.9 1594 14.1 34.0 1208 11.6 67.7 1755 16.4 16.2 776 8.0 36.0 851

15892 45.00 20.00 3.00 0.40 0.50 186.0 4.2 16.7 39.2 1387 14.5 5.0 319 5.2 40.9 1401 14.8 3.3 262 4.2 12.2 558

15339 46.00 17.00 2.00 0.50 0.33 122.0 3.1 17.6 27.2 957 14.9 2.2 160 4.3 27.9 965 15.1 1.5 135 3.5 9.4 163

15308 46.00 34.00 3.00 0.76 0.63 231.0 8.3 14.3 50.1 1583 14.7 23.6 920 10.1 61.1 1689 16.3 12.6 646 7.4 28.4 693

15523 48.00 25.00 2.00 0.50 0.39 142.0 5.0 16.5 34.9 1110 15.7 6.9 347 7.0 37.5 1140 16.3 4.3 274 5.5 16.3 189

15954 50.00 15.00 2.00 0.40 0.34 126.0 2.5 20.0 32.8 1093 16.1 1.6 125 3.5 33.2 1097 16.2 1.1 109 3.0 6.7 168

15893 50.00 15.00 2.50 0.40 0.42 156.3 2.8 20.3 40.2 1351 16.0 1.9 153 3.5 40.7 1354 16.1 1.4 134 3.0 6.5 326

15877 50.00 20.00 2.00 0.40 0.37 136.0 3.6 18.6 36.1 1152 16.3 3.7 223 5.2 37.3 1164 16.6 2.5 186 4.2 10.7 181

15937 50.00 20.00 3.00 0.40 0.54 201.0 4.0 19.0 52.4 1692 16.1 5.1 322 5.1 54.0 1704 16.4 3.5 269 4.2 10.4 603

Torsion

ConstantProfile

Number


A

mm

B

mm

R1

mm

Mass

kg/m

T

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg


(continued)

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

55

y 2

Cyy

Cx1

x

2

x

1

T

o90

A

B

T

150012 50.00 25.00 1.60 0.40 0.32 117.4 4.8 17.3 31.6 967 16.4 5.7 282 7.0 33.7 992 17.0 3.6 226 5.5 15.4 100

15987 50.00 25.00 3.00 0.40 0.59 216.0 5.3 17.8 56.7 1761 16.2 9.9 505 6.8 60.3 1794 16.7 6.3 403 5.4 15.0 648

15956 50.00 25.00 4.00 0.40 0.77 284.0 5.7 18.2 73.2 2302 16.1 12.6 653 6.7 77.7 2332 16.5 8.2 523 5.4 14.7 1515

15571 50.00 30.00 2.00 0.40 0.42 156.0 6.4 16.4 41.5 1236 16.3 11.8 498 8.7 46.4 1288 17.2 6.9 381 6.7 20.5 208

15932 50.00 30.00 3.00 0.40 0.63 231.0 6.8 16.8 60.4 1817 16.2 16.9 726 8.5 67.2 1882 17.1 10.0 553 6.6 20.2 693

15933 50.00 30.00 4.00 0.40 0.82 304.0 7.1 17.1 78.1 2376 16.0 21.5 941 8.4 86.7 2444 16.9 13.0 716 6.5 19.9 1621

15564 50.00 40.00 3.00 0.40 0.71 261.0 10.0 15.0 66.6 1903 16.0 38.3 1277 12.1 85.6 2071 18.1 19.3 862 8.6 32.4 783

15248 50.80 25.40 1.60 0.64 0.32 119.4 4.9 17.6 33.2 998 16.7 6.0 292 7.1 35.4 1024 17.2 3.8 233 5.6 15.4 102

15073 50.80 25.40 2.02 0.76 0.41 149.8 5.0 17.7 41.3 1249 16.6 7.4 363 7.0 44.1 1279 17.2 4.7 290 5.6 15.3 204

15075 50.80 25.40 6.36 0.76 1.20 444.2 6.6 19.3 113.9 3621 16.0 19.0 1010 6.5 120.0 3627 16.4 12.8 825 5.4 13.8 5989

15976 50.80 12.70 3.18 0.50 0.52 191.8 2.6 21.6 49.3 1692 16.0 1.4 138 2.7 49.6 1690 16.1 1.1 126 2.4 4.6 647

15839 50.80 19.05 3.18 0.40 0.57 212.0 3.9 19.7 56.7 1824 16.3 4.7 308 4.7 58.1 1833 16.6 3.3 261 3.9 9.3 715

15840 50.80 25.40 3.18 0.40 0.63 232.2 5.5 18.2 62.7 1922 16.4 11.0 550 6.9 66.7 1956 16.9 7.0 439 5.5 14.9 783

15849 50.80 25.40 4.76 0.40 0.92 340.1 6.0 18.7 89.4 2790 16.2 15.2 786 6.7 94.7 2818 16.7 10.0 632 5.4 14.4 2568

15841 50.80 38.10 3.18 0.40 0.74 272.6 9.4 15.7 72.2 2056 16.3 35.3 1228 11.4 88.8 2203 18.1 18.7 857 8.3 29.1 919

15902 50.80 38.10 4.76 0.40 1.09 400.5 9.9 16.3 103.2 2989 16.1 49.9 1772 11.2 126.3 3159 17.8 26.8 1228 8.2 28.8 3025

15894 55.00 15.00 2.00 0.40 0.37 136.0 2.4 22.4 42.5 1306 17.7 1.6 126 3.4 43.0 1309 17.8 1.2 111 2.9 5.8 181

15927 60.00 15.00 2.00 0.40 0.40 146.0 2.3 24.8 54.0 1536 19.2 1.6 127 3.3 54.4 1539 19.3 1.2 113 2.9 5.0 195

15582 60.00 25.00 2.00 0.40 0.45 166.0 4.5 22.0 64.0 1683 19.6 7.3 354 6.6 66.5 1706 20.0 4.8 292 5.4 11.5 221

15923 60.00 25.00 2.50 0.40 0.56 206.3 4.7 22.2 78.9 2085 19.6 8.8 435 6.5 81.8 2111 19.9 5.9 359 5.3 11.4 430

15857 60.00 30.00 3.00 0.40 0.71 261.0 6.2 21.2 99.5 2562 19.5 17.6 739 8.2 106.0 2616 20.1 11.2 590 6.5 15.1 783

15953 60.00 30.00 4.00 0.40 0.93 344.0 6.5 21.5 129.2 3358 19.4 22.5 959 8.1 137.3 3415 20.0 14.4 766 6.5 14.9 1835

15924 60.00 40.00 3.00 0.40 0.79 291.0 9.1 19.1 109.9 2689 19.4 40.3 1304 11.8 127.5 2834 20.9 22.7 960 8.8 24.2 873

15929 60.00 40.00 4.00 0.40 1.04 384.0 9.5 19.5 142.9 3527 19.3 51.9 1701 11.6 165.3 3695 20.7 29.5 1248 8.8 24.0 2048

15888 60.00 40.00 5.00 0.40 1.29 475.0 9.9 19.9 174.2 4340 19.1 62.7 2081 11.5 200.9 4517 20.6 36.0 1524 8.7 23.7 3958

15959 60.00 40.00 6.00 0.40 1.53 564.0 10.2 20.2 203.9 5127 19.0 72.8 2446 11.4 234.5 5303 20.4 42.2 1791 8.7 23.5 6768

15361 60.00 41.50 2.50 0.50 0.67 247.5 9.4 18.7 93.9 2273 19.5 37.9 1181 12.4 110.9 2418 21.2 20.9 860 9.2 25.8 516

15899 60.00 50.00 2.00 0.40 0.59 216.0 12.1 17.1 80.9 1886 19.4 51.8 1367 15.5 107.7 2100 22.3 25.0 913 10.8 34.7 288

15570 60.00 50.00 4.00 0.50 1.15 424.0 12.8 17.8 154.0 3652 19.1 97.9 2634 15.2 204.0 4002 21.9 47.8 1729 10.6 34.5 2261

15078 63.50 25.40 3.18 0.76 0.73 272.6 4.9 23.9 115.6 2922 20.6 11.5 561 6.5 119.4 2949 20.9 7.8 468 5.3 10.5 919

150010 63.50 38.10 3.18 0.40 0.85 313.0 8.3 21.0 133.2 3137 20.6 37.5 1259 10.9 148.5 3259 21.8 22.2 960 8.4 20.3 1055

15903 63.50 38.10 4.76 0.40 1.25 461.0 8.9 21.6 191.9 4583 20.4 53.0 1819 10.7 213.0 4722 21.5 31.8 1384 8.3 20.0 3481

Torsion

ConstantProfile

Number


A

mm

B

mm

R1

mm

Mass

kg/m

T

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg


(continued)

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

56

y 2

Cyy

Cx1

x

2

x

1

T

o90

A

B

T

15989 63.50 38.10 6.35 0.40 1.64 604.8 9.5 22.2 246.5 5971 20.2 67.1 2347 10.5 272.5 6101 21.2 41.0 1789 8.2 19.6 8130

15262 63.50 50.80 6.36 0.64 1.86 686.5 13.6 20.0 272.7 6266 19.9 155.1 4175 15.0 348.1 6689 22.5 79.7 2783 10.8 32.0 9256

15375 70.00 50.00 1.50 0.30 0.48 177.8 11.0 21.0 93.3 1904 22.9 41.1 1054 15.2 112.3 2054 25.1 22.1 764 11.2 27.3 133

150025 70.00 60.00 2.00 0.60 0.69 256.0 14.6 19.6 130.5 2590 22.6 89.7 1975 18.7 178.0 2913 26.4 42.2 1299 12.8 36.2 341

15374 70.50 53.00 6.00 0.50 1.91 705.0 13.6 22.4 352.3 7318 22.4 172.0 4366 15.6 432.6 7767 24.8 91.8 3026 11.4 29.0 8460

15522 71.00 25.00 2.00 0.50 0.51 188.0 4.1 27.1 101.1 2300 23.2 7.5 358 6.3 103.4 2320 23.5 5.2 303 5.2 8.9 251

15348 75.00 20.00 5.00 0.30 1.22 450.0 4.2 31.7 253.1 5840 23.7 8.4 533 4.3 255.0 5835 23.8 6.5 482 3.8 5.1 3750

15520 75.00 25.00 2.00 0.50 0.53 196.0 3.9 28.9 117.3 2545 24.5 7.6 360 6.2 119.6 2564 24.7 5.3 307 5.2 8.2 261

15999 75.00 50.00 3.00 0.40 0.99 366.0 11.1 23.6 218.0 4243 24.4 80.3 2066 14.8 253.2 4490 26.3 45.1 1526 11.1 24.3 1098

15517 75.00 50.00 4.00 0.50 1.31 484.0 11.5 24.0 284.7 5583 24.3 104.1 2705 14.7 330.1 5879 26.1 58.8 1990 11.0 24.1 2581

15969 75.00 50.00 6.00 0.40 1.94 714.0 12.2 24.7 410.2 8163 24.0 147.9 3918 14.4 473.5 8508 25.8 84.7 2871 10.9 23.8 8568

15569 76.00 22.00 1.50 0.40 0.39 144.8 3.1 30.1 88.5 1927 24.7 4.0 213 5.3 89.6 1937 24.9 2.9 185 4.5 6.6 109

15504 76.00 22.00 2.00 0.40 0.52 192.0 3.3 30.3 116.6 2550 24.6 5.2 279 5.2 118.0 2561 24.8 3.7 242 4.4 6.5 256

15355 76.00 38.00 2.00 0.50 0.61 224.0 7.1 26.1 140.1 2808 25.0 25.5 824 10.7 149.6 2885 25.8 16.0 659 8.4 15.5 299

15083 76.20 19.44 1.78 0.76 0.46 167.1 2.7 31.1 101.0 2239 24.6 3.3 195 4.4 101.9 2246 24.7 2.4 172 3.8 5.3 176

15421 76.20 25.40 2.03 0.76 0.55 202.1 4.0 29.4 124.8 2667 24.9 8.1 377 6.3 127.3 2687 25.1 5.6 321 5.3 8.2 278

15842 76.20 25.40 3.18 0.40 0.85 313.0 4.5 29.9 190.4 4108 24.7 11.9 570 6.2 193.9 4129 24.9 8.4 488 5.2 7.9 1055

15085 76.20 38.10 3.18 0.40 0.96 353.4 7.6 26.6 219.0 4417 24.9 39.1 1282 10.5 233.4 4520 25.7 24.7 1023 8.4 15.2 1191

15252 76.20 38.10 4.74 0.64 1.41 519.3 8.2 27.2 315.8 6448 24.7 55.3 1846 10.3 335.8 6563 25.4 35.3 1474 8.2 14.9 3889

15988 76.20 38.10 6.35 0.40 1.86 685.5 8.8 27.8 409.2 8460 24.4 70.2 2394 10.1 433.9 8565 25.2 45.6 1920 8.2 14.6 9213

15843 76.20 50.80 3.18 0.40 1.07 393.7 11.4 24.1 241.7 4635 24.8 88.9 2255 15.0 280.6 4901 26.7 50.0 1664 11.3 24.3 1327

150015 76.20 50.80 4.50 0.40 1.49 551.3 11.9 24.6 333.0 6448 24.6 121.4 3117 14.8 385.7 6774 26.5 68.7 2291 11.2 24.1 3721

15263 76.20 50.80 6.35 0.64 2.08 766.1 12.5 25.2 453.1 8889 24.3 163.1 4262 14.6 522.6 9253 26.1 93.5 3122 11.1 23.7 10297

15086 76.20 63.50 7.96 0.76 2.84 1048.7 17.4 23.7 594.1 11319 23.8 374.6 8120 18.9 782.3 12169 27.3 186.4 5261 13.3 34.2 22148

15936 80.00 20.00 2.00 0.40 0.53 196.0 2.8 32.8 130.1 2758 25.8 4.0 231 4.5 131.1 2765 25.9 2.9 204 3.9 5.2 261

15942 80.00 25.00 2.50 0.40 0.69 256.3 4.0 31.5 172.7 3560 26.0 9.3 444 6.0 175.4 3579 26.2 6.6 382 5.1 7.3 534

15925 80.00 30.00 3.00 0.40 0.87 321.0 5.3 30.3 217.9 4384 26.1 18.7 758 7.6 223.9 4424 26.4 12.8 636 6.3 9.7 963

15920 80.00 40.00 3.00 0.40 0.95 351.0 7.8 27.8 240.7 4613 26.2 43.2 1343 11.1 256.7 4725 27.0 27.2 1072 8.8 15.3 1053

15870 80.00 40.00 4.00 0.40 1.26 464.0 8.2 28.2 314.5 6072 26.0 55.7 1752 11.0 334.9 6200 26.9 35.3 1398 8.7 15.1 2475

15863 80.00 40.00 5.00 0.40 1.56 575.0 8.6 28.6 385.3 7494 25.9 67.4 2145 10.8 409.7 7628 26.7 43.0 1713 8.7 14.9 4792

15455 84.50 28.00 1.40 0.76 0.46 155.5 4.1 32.3 119.3 2286 27.7 7.8 324 7.1 121.7 2305 28.0 5.4 276 5.9 8.2 102

15850 88.90 31.75 3.18 0.40 1.01 373.6 5.5 34.0 312.7 5699 28.9 23.7 903 8.0 320.1 5743 29.3 16.4 763 6.6 9.0 1259

Torsion

ConstantProfile

Number


A

mm

B

mm

R1

mm

Mass

kg/m

T

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg


(continued)

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

57


(continued)

y 2

Cyy

Cx1

x

2

x

1

T

o90

A

B

T

15087 88.90 63.50 9.52 0.78 3.69 1360.2 16.8 29.5 1066.8 17946 28.0 453.5 9701 18.3 1266.5 18694 30.5 253.8 6885 13.7 26.4 41092

15356 100.00 35.00 3.00 0.50 1.07 396.0 5.7 38.2 421.3 6822 32.6 30.7 1049 8.8 430.8 6877 33.0 21.2 889 7.3 8.8 1188

15919 100.00 40.00 3.00 0.40 1.11 411.0 6.9 36.9 440.8 6986 32.7 45.3 1369 10.5 455.8 7076 33.3 30.3 1137 8.6 10.8 1233

15934 100.00 40.00 4.00 0.40 1.47 544.0 7.3 37.3 577.8 9214 32.6 58.4 1787 10.4 597.0 9316 33.1 39.3 1486 8.5 10.7 2901

15878 100.00 50.00 3.00 0.40 1.20 441.0 9.5 34.5 475.8 7264 32.8 86.1 2126 14.0 507.9 7456 33.9 54.1 1699 11.1 15.4 1323

15518 100.00 50.00 4.00 0.76 1.58 584.0 9.9 34.9 624.2 9585 32.7 111.7 2785 13.8 665.5 9813 33.8 70.4 2223 11.0 15.3 3115

15858 100.00 50.00 5.00 0.40 1.96 725.0 10.3 35.3 767.8 11859 32.5 136.0 3422 13.7 817.6 12110 33.6 86.2 2730 10.9 15.1 6042

15887 100.00 50.00 6.00 0.40 2.34 864.0 10.6 35.6 906.7 14087 32.4 159.0 4039 13.6 964.3 14348 33.4 101.4 3224 10.8 15.0 10368

15900 100.00 70.00 2.00 0.40 0.91 336.0 15.2 30.2 361.1 5171 32.8 151.6 2765 21.2 430.3 5560 35.8 82.5 2021 15.7 26.5 448

15844 101.60 50.80 3.18 0.40 1.29 474.5 9.7 35.1 527.9 7937 33.4 95.4 2321 14.2 563.4 8144 34.5 59.9 1854 11.2 15.4 1600

15977 101.60 50.80 6.35 0.40 2.51 927.4 10.9 36.3 1002.4 15351 32.9 175.3 4395 13.7 1065.7 15626 33.9 112.0 3509 11.0 14.9 12465

150008 101.60 76.20 6.35 0.40 2.95 1088.7 18.7 31.4 1153.2 16426 32.5 564.1 9809 22.8 1419.2 17601 36.1 298.1 6847 16.5 29.1 14633

15524 110.00 25.00 2.00 0.50 0.72 266.0 3.2 45.7 332.8 5173 35.4 8.0 368 5.5 334.9 5185 35.5 6.0 327 4.8 4.5 355

15364 110.00 90.00 8.00 0.30 4.16 1536.0 23.2 33.2 1869.2 24345 34.9 1133.3 16971 27.2 2439.0 26477 39.8 563.5 11243 19.2 33.4 32768

15519 115.00 25.00 2.00 0.50 0.75 276.0 3.1 48.1 375.9 5618 36.9 8.1 369 5.4 377.9 5628 37.0 6.1 330 4.7 4.2 368

15962 120.00 60.00 8.00 0.40 3.73 1376.0 13.1 43.1 2066.9 26868 38.8 360.1 7672 16.2 2196.4 27318 40.0 230.6 6130 12.9 14.9 29355

15944 120.00 80.00 3.00 0.40 1.60 591.0 17.1 37.1 913.8 11028 39.3 339.5 5401 24.0 1063.6 11731 42.4 189.8 4009 17.9 24.5 1773

15943 120.00 100.00 4.00 0.40 2.34 864.0 24.2 34.2 1294.3 15089 38.7 828.9 10938 31.0 1722.6 16798 44.7 400.6 7303 21.5 34.7 4608

15290 127.00 50.80 2.02 0.76 0.96 355.1 8.1 46.2 622.9 7705 41.9 65.6 1534 13.6 644.9 7826 42.6 43.5 1275 11.1 11.0 483

15971 130.00 100.00 8.00 0.50 4.81 1776.0 24.7 39.7 3073.6 34045 41.6 1602.1 21283 30.0 3844.3 36692 46.5 831.5 14669 21.6 30.4 37888

15952 150.00 50.00 4.00 0.40 2.12 784.0 7.9 57.9 1876.2 20364 48.9 121.3 2878 12.4 1913.0 20513 49.4 84.4 2453 10.4 8.2 4181

150017 150.00 50.00 6.00 0.50 3.15 1164.0 8.7 58.7 2748.3 30092 48.6 172.9 4183 12.2 2799.7 30253 49.0 121.5 3577 10.2 8.0 13968

15958 150.00 100.00 10.00 0.40 6.50 2400.0 23.8 48.8 5580.4 55115 48.2 2026.3 26574 29.1 6455.5 57738 51.9 1151.2 19503 21.9 24.0 80000

150006 152.40 76.20 6.35 0.40 3.82 1411.3 15.1 53.2 3498.1 35280 49.8 625.1 10239 21.0 3728.8 36103 51.4 394.4 8171 16.7 15.3 18969

15983 152.40 76.20 9.53 0.40 5.66 2087.7 16.4 54.5 5076.9 51837 49.3 888.0 14839 20.6 5397.8 52762 50.8 567.1 11849 16.5 14.9 63203

Torsion

ConstantProfile

Number


A

mm

B

mm

R1

mm

Mass

kg/m

T

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

58

Angle Type 6 Unequal angle, with outside cornerradius (R) less than or equal to 0.802

y 2

Cyy

Cx1

x

2

x

1

T

o90A

B

T

R1

R2

R2

15002 38.10 25.40 3.18 5.08 0.64 0.53 197.2 6.3 12.6 29.2 1142 12.2 10.6 553 7.3 33.7 1189 13.1 6.0 405 5.5 23.8 647

15214 50.80 25.40 3.18 5.33 0.64 0.65 238.1 5.5 18.0 64.5 1968 16.5 11.3 570 6.9 68.6 2002 17.0 7.3 455 5.5 15.0 783

15272 50.80 38.10 6.34 6.34 0.76 1.44 531.8 10.6 16.9 134.0 3956 15.9 64.7 2351 11.0 163.6 4125 17.5 35.1 1615 8.1 28.7 7013

15216 63.50 38.10 3.18 6.10 0.64 0.87 320.8 8.4 20.8 136.5 3200 20.6 38.4 1290 10.9 151.9 3320 21.8 23.0 991 8.5 20.2 1055

15011 63.50 50.80 9.52 7.96 0.76 2.74 1010.9 14.9 21.2 386.4 9136 19.6 218.5 6081 14.7 489.7 9515 22.0 115.2 4011 10.7 31.7 30135

15010 63.50 50.80 3.18 6.60 0.64 0.98 362.5 12.4 18.6 150.1 3344 20.3 86.5 2251 15.4 192.1 3646 23.0 44.4 1549 11.1 32.3 1191

15012 63.50 50.80 6.36 6.60 0.64 1.92 695.7 13.7 20.0 276.9 6365 19.9 158.0 4257 15.1 353.8 6794 22.6 81.0 2837 10.8 32.1 9256

15013 76.20 25.40 6.36 7.92 0.64 1.68 619.0 5.8 30.9 363.2 8010 24.2 21.8 1113 5.9 369.0 8006 24.4 15.9 971 5.1 7.4 8167

15018 76.20 38.10 9.52 6.36 0.64 2.73 1006.0 10.0 29.1 582.5 12361 24.1 98.1 3497 9.9 614.7 12385 24.7 65.9 2843 8.1 14.0 30135

15016 76.20 50.80 6.36 6.86 0.64 2.11 777.2 12.6 25.2 460.4 9029 24.3 166.3 4351 14.6 531.3 9397 26.1 95.4 3190 11.1 23.8 10345

15017 76.20 50.80 7.96 6.86 0.64 2.59 957.5 13.2 25.8 557.6 11074 24.1 199.7 5310 14.4 641.6 11436 25.9 115.7 3882 11.0 23.6 20013

15225 88.90 63.50 9.54 7.62 0.64 3.73 1375.2 16.8 29.5 1080.5 18188 28.0 460.9 9875 18.3 1284.2 18946 30.6 257.2 7000 13.7 26.4 41346

15228 88.90 76.20 12.70 8.13 0.64 5.28 1949.5 22.3 28.7 1453.3 24123 27.3 981.0 18199 22.4 1948.9 25575 31.6 485.4 11424 15.8 35.6 104058

15271 101.60 50.80 9.52 8.12 0.76 3.72 1374.1 12.2 37.5 1449.7 22613 32.5 248.5 6438 13.4 1536.3 22837 33.4 162.0 5166 10.9 14.5 41092

15024 101.60 63.50 6.36 8.12 0.64 2.77 1023.6 14.6 33.5 1101.1 16170 32.8 340.6 6970 18.2 1241.1 16802 34.8 200.6 5256 14.0 21.5 13612

15025 101.60 76.20 9.52 8.38 0.64 4.38 1616.9 19.9 32.5 1668.5 24163 32.1 808.9 14368 22.4 2042.9 25532 35.5 434.6 9964 16.4 28.8 48397

15027 127.00 76.20 9.52 9.14 0.64 5.04 1861.6 17.9 43.2 3102.6 37013 40.8 859.1 14741 21.5 3444.7 38129 43.0 517.0 11230 16.7 20.0 55702

15327 140.00 50.00 3.00 3.00 0.50 1.51 562.8 7.8 52.8 1189.3 13639 46.0 93.5 2217 12.9 1219.0 13778 46.5 63.8 1872 10.6 9.2 1683

15991 140.00 100.00 6.00 5.00 0.40 5.35 1409.3 23.1 43.1 2904.7 29966 45.4 1269.3 16506 30.0 3485.9 32050 49.7 688.1 11880 22.1 27.1 16848

15350 150.00 45.00 5.00 5.00 0.50 2.59 955.3 7.3 59.6 2258.2 24988 48.6 109.8 2912 10.7 2289.4 25091 49.0 78.6 2522 9.1 6.8 7917

15028 152.40 76.20 9.52 9.90 0.64 5.71 2106.5 16.4 54.2 5129.5 52260 49.3 898.1 15019 20.6 5452.5 53184 50.9 575.1 12010 16.5 14.9 63008

15231 152.40 76.20 12.70 9.90 0.64 7.49 2762.8 17.6 55.6 6606.6 68227 48.9 1137.0 19412 20.3 7006.4 69074 50.4 737.2 15557 16.3 14.6 147415

15457 152.40 88.90 9.52 10.42 0.76 6.04 2229.6 20.0 51.6 5416.7 53715 49.3 1407.2 20430 25.1 5971.6 55384 51.8 852.3 15719 19.6 19.2 66660

Torsion

ConstantProfile

Number


A

mm

B

mm

R2

mm

Mass

kg/m

T

mm

R1

mm

Area

mm2

Cy

mm

Cx

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

r

mm

I1

x103mm

4

Z1

mm3

r

mm

J

mm4

I2

x103mm

4

Z2

mm3

r

mm

Angle

deg

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

59

o90A

T1

T1

B

R1

y

y

x x

e

CyChannel Type 1 No radius

Hulam


atalogueAugust 2007

Centroid

16007 9.52 9.52 1.60 0.76 0.110 40.8 0.5 109 3.6 0.4 61 2.9 3.8 2.9 35

16008 9.52 12.70 1.60 0.76 0.138 51.0 0.7 143 3.7 0.8 107 4.0 5.2 4.4 43

16502 9.52 19.06 1.58 0.25 0.190 70.3 1.0 209 3.8 2.5 230 5.9 8.3 7.6 58

16009 10.00 10.00 1.50 0.26 0.110 40.5 0.6 118 3.8 0.4 64 3.1 3.9 3.2 30

16895 10.00 10.00 2.00 0.40 0.141 52.1 0.7 138 3.6 0.5 82 3.1 4.1 2.8 69

16500 11.00 10.00 1.50 0.50 0.114 42.1 0.7 136 4.2 0.4 66 3.1 3.8 3.1 32

16472 12.00 10.00 1.50 0.40 0.117 43.6 0.9 154 4.6 0.4 67 3.1 3.7 3.1 33

16016 12.70 9.52 1.52 0.76 0.117 43.9 1.0 162 4.8 0.4 62 2.9 3.4 2.8 34

16445 12.70 12.70 1.50 0.50 0.143 52.8 1.3 208 5.0 0.8 107 4.0 4.8 4.3 39

16018 12.70 12.70 2.04 0.76 0.187 69.6 1.6 252 4.8 1.1 140 3.9 5.0 3.9 96

16020 12.70 12.70 3.18 0.76 0.273 101.2 2.0 310 4.4 1.5 201 3.8 5.4 2.9 340

16824 12.70 19.05 3.18 0.40 0.383 141.4 2.9 459 4.5 4.8 448 5.8 8.4 5.9 476

16022 14.30 7.96 1.60 0.64 0.115 43.4 1.2 171 5.3 0.2 46 2.4 2.7 1.9 37

16473 15.00 10.00 1.50 0.40 0.130 48.1 1.6 212 5.8 0.5 69 3.1 3.4 2.9 36

16465 15.00 15.00 1.50 0.40 0.170 63.1 2.3 304 6.0 1.4 152 4.8 5.6 5.3 47

16885 15.00 15.00 2.00 0.40 0.222 82.1 2.8 371 5.8 1.8 196 4.7 5.8 5.0 109

16026 15.87 12.70 1.63 0.82 0.168 62.2 2.4 301 6.2 1.0 120 4.0 4.5 4.1 55

16027 15.88 15.88 1.60 0.40 0.192 71.2 2.9 362 6.4 1.8 182 5.0 5.9 5.6 61

160042 15.88 15.88 3.18 0.40 0.355 131.3 4.4 553 5.8 3.1 328 4.8 6.5 4.4 442

16444 16.00 48.50 3.00 0.50 0.918 321.1 12.8 1596 6.3 71.2 2698 14.9 22.1 20.4 963

160037 17.00 20.00 1.45 0.40 0.212 78.5 3.9 454 7.0 3.2 261 6.4 7.6 7.7 55

16470 18.00 20.00 1.45 0.40 0.212 80.0 4.4 489 7.4 3.3 264 6.4 7.5 7.7 56

160026 18.70 38.00 1.85 0.50 0.450 168.5 10.5 1128 7.9 24.5 1115 12.1 16.0 16.2 192

16348 19.00 20.00 1.50 0.50 0.230 84.1 5.1 539 7.8 3.5 275 6.4 7.3 7.6 63

16223 19.05 19.05 3.18 0.50 0.437 161.6 8.3 869 7.2 5.6 487 5.9 7.5 5.8 544

16031 19.06 12.70 1.60 0.76 0.178 66.3 3.7 383 7.4 1.0 122 4.0 4.2 3.9 56

16032 19.06 12.70 3.18 0.64 0.327 121.3 5.7 599 6.9 1.7 218 3.8 4.8 2.7 408

16464 20.00 10.00 2.00 0.40 0.195 72.1 3.9 394 7.4 0.6 93 3.0 3.2 2.3 96

16341 20.00 15.00 2.00 0.50 0.249 92.1 5.6 557 7.8 2.0 207 4.7 5.2 4.7 123

16466 20.00 20.00 1.50 0.40 0.231 85.6 5.8 576 8.2 3.5 277 6.4 7.2 7.5 64

16867 20.00 20.00 2.00 0.40 0.303 112.1 7.2 719 8.0 4.5 360 6.4 7.4 7.1 149

16887 20.00 30.00 2.00 0.40 0.412 152.1 10.4 1045 8.3 14.0 778 9.6 12.0 12.0 203

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number

Dimensions X-X Axis Y-Y Axis

A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

60

o90A

T1

T1

B

R1

y

y

x x

e

CyChannel Type 1 No radius(continued)

Hulam


atalogueAugust 2007

Centroid

16396 21.00 18.60 1.20 0.30 0.196 67.0 5.0 479 8.7 2.4 198 6.0 6.4 7.0 32

16902 21.00 25.00 2.50 0.50 0.446 165.1 11.6 1107 8.4 10.4 681 7.9 9.8 9.1 344

16857 21.20 30.00 2.00 0.50 0.418 154.5 12.0 1128 8.8 14.3 787 9.6 11.9 12.0 206

16907 21.80 21.80 6.00 0.50 0.868 320.5 17.6 1613 7.4 13.5 1096 6.5 9.4 4.5 3845

160027 22.22 22.22 3.17 0.50 0.518 191.3 14.0 1257 8.5 9.2 676 6.9 8.6 7.2 640

16710 22.23 22.23 1.63 0.50 0.280 103.5 8.6 777 9.1 5.3 373 7.2 8.0 8.4 92

16357 22.61 69.85 1.78 0.50 0.766 282.7 28.1 2483 10.0 135.8 3479 21.9 30.8 31.8 298

16430 23.00 6.00 2.00 0.50 0.167 62.1 3.8 331 7.8 0.1 34 1.5 1.8 0.4 83

16919 23.00 25.00 2.00 0.50 0.373 138.1 12.2 1062 9.4 8.9 566 8.0 9.3 9.4 184

16220 23.17 23.17 1.27 0.38 0.232 85.1 8.0 691 9.7 4.8 322 7.5 8.2 9.0 46

16041 23.24 22.98 1.40 0.76 0.251 93.2 8.7 749 9.7 5.2 348 7.4 8.2 8.8 61

16417 23.82 35.00 1.60 0.64 0.392 145.2 15.0 1262 10.2 18.6 871 11.3 13.7 14.6 124

16043 23.82 50.80 1.60 0.78 0.528 195.8 21.3 1788 10.4 51.7 1747 16.2 21.2 22.4 167

16421 24.00 38.00 3.00 0.50 0.764 282.1 26.8 2231 9.7 40.9 1828 12.0 15.6 15.0 846

16923 25.00 12.00 1.50 0.50 0.186 69.1 6.3 506 9.6 0.9 107 3.6 3.5 3.4 52

16395 25.00 20.00 1.50 0.30 0.251 93.0 9.6 770 10.2 3.8 288 6.4 6.7 7.2 70

16428 25.00 20.00 3.50 0.20 0.550 203.0 18.0 1442 9.4 7.7 612 6.2 7.4 5.7 829

16446 25.00 25.00 2.00 0.40 0.384 142.1 14.8 1185 10.2 9.1 575 8.0 9.1 9.3 189

16448 25.00 25.00 3.00 0.40 0.561 207.1 20.0 1599 9.8 12.9 828 7.9 9.5 8.5 621

16505 25.40 12.70 1.58 0.50 0.202 75.4 7.2 564 9.7 1.1 126 3.9 3.8 3.6 63

16825 25.40 12.70 3.18 0.40 0.383 141.4 11.9 935 9.2 1.9 229 3.7 4.3 2.5 476

16048 25.40 15.88 1.60 0.64 0.234 86.5 8.7 684 10.0 2.1 197 5.0 5.0 5.1 74

16826 25.40 19.05 3.18 0.40 0.492 181.8 16.9 1330 9.6 6.3 514 5.9 6.9 5.5 612

16827 25.40 25.40 3.18 0.40 0.601 222.2 21.9 1725 9.9 14.2 901 8.0 9.7 8.6 749

16828 25.40 50.80 3.18 0.40 1.039 383.7 42.0 3306 10.5 98.5 3377 16.0 21.6 21.0 1293

160036 25.40 63.50 3.18 0.40 0.930 464.5 52.0 4096 10.6 183.7 5148 19.9 27.8 27.3 1565

16881 25.70 23.60 1.60 0.50 0.302 111.6 12.5 974 10.6 6.5 421 7.6 8.2 8.9 95

160002 27.00 20.00 3.00 0.50 0.496 183.1 19.7 1459 10.4 7.0 544 6.2 7.1 6.0 549

16339 29.00 12.70 1.20 0.50 0.169 62.5 7.8 537 11.2 0.9 100 3.9 3.4 3.8 30

16530 29.00 65.00 3.00 0.50 1.479 459.1 69.3 4776 12.3 193.8 5214 20.5 27.8 28.0 1377

16254 29.46 30.15 3.18 0.64 0.719 265.4 36.6 2482 11.7 24.3 1289 9.6 11.3 10.7 894

16056 29.84 15.88 3.18 0.76 0.450 175.9 21.5 1441 11.1 3.9 368 4.7 5.2 3.8 592

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number


A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

61

Channel Type 1 No radius(continued)

Hulam


atalogueAugust 2007

o90A

T1

T1

B

R1

y

y

x x

e

Cy

Centroid

16889 30.00 20.00 2.00 0.40 0.357 132.1 18.6 1243 11.9 5.2 387 6.3 6.5 6.6 176

16927 30.00 23.00 2.00 0.50 0.498 144.1 21.0 1401 12.1 7.7 506 7.3 7.7 8.0 192

16449 30.00 30.00 3.00 0.40 0.683 252.1 36.4 2427 12.0 22.9 1216 9.5 11.1 10.7 756

16830 31.75 31.75 3.18 0.40 0.766 282.7 45.7 2880 12.7 28.8 1443 10.1 11.8 11.3 953

16059 31.76 12.70 3.18 0.64 0.438 161.7 20.9 1318 11.4 2.1 237 3.6 4.0 2.2 545

16061 31.76 25.40 2.64 0.76 0.553 204.3 32.6 2055 12.6 13.2 796 8.0 8.8 8.6 474

16072 31.76 63.50 1.90 0.76 0.821 294.7 57.4 3613 14.0 122.5 3283 20.4 26.2 27.9 354

16384 32.00 12.00 1.50 0.50 0.214 79.6 11.4 716 12.0 1.0 111 3.5 3.1 3.1 60

16066 32.14 25.40 3.18 0.64 0.660 243.7 38.6 2401 12.6 15.5 941 8.0 9.0 8.2 821

16067 32.20 19.04 1.56 0.64 0.289 104.9 17.2 1068 12.8 3.8 283 6.0 5.7 6.3 85

16389 33.25 38.00 1.50 0.50 0.431 159.5 32.2 1939 14.2 24.6 1014 12.4 13.8 15.5 120

16476 33.50 35.00 2.00 0.50 0.560 199.1 39.1 2333 14.0 25.6 1144 11.3 12.6 13.7 265

16255 34.93 12.83 1.52 0.76 0.236 87.7 15.1 862 13.1 1.2 129 3.8 3.3 3.3 67

160014 35.20 100.00 2.00 0.50 1.253 462.5 115.4 6559 15.8 463.1 8180 31.6 43.4 45.8 617

16069 35.36 9.52 1.58 0.64 0.220 81.1 13.0 737 12.7 0.5 74 2.6 2.3 1.8 67

16354 36.00 27.40 2.00 0.50 0.470 173.7 37.2 2067 14.6 13.4 729 8.8 9.0 9.8 231

16372 38.00 25.00 2.00 0.20 0.455 168.0 39.0 2052 15.2 10.6 617 7.9 7.8 8.6 224

16408 38.00 50.00 6.00 0.25 2.049 756.0 164.2 8642 14.7 185.4 6276 15.7 20.5 17.7 9072

16832 38.10 19.05 3.18 0.40 0.601 222.2 45.5 2390 14.3 7.2 550 5.7 5.9 4.9 749

16833 38.10 25.40 3.18 0.40 0.711 262.5 57.9 3038 14.8 16.4 969 7.9 8.4 7.9 885

16077 38.10 25.40 6.36 0.64 1.312 484.7 91.2 4785 13.7 27.7 1743 7.6 9.5 5.5 6533

16079 38.10 28.58 3.18 0.64 0.767 282.9 64.1 3364 15.1 22.9 1218 9.0 9.8 9.4 953

16834 38.10 38.10 3.18 0.40 0.930 343.3 82.6 4334 15.5 51.1 2114 12.2 13.9 14.1 1157

160035 38.10 38.10 6.35 0.40 1.748 645.2 132.3 6942 14.3 89.6 3891 11.8 15.1 11.6 8671

16426 39.20 32.00 1.70 0.76 0.458 169.9 44.9 2288 16.2 18.3 852 10.4 10.6 12.1 163

16450 40.00 20.00 2.00 0.40 0.412 152.1 36.7 1835 15.5 5.8 404 6.2 5.7 6.1 203

16463 40.00 29.00 3.00 0.50 0.796 276.1 69.5 3477 15.9 23.1 1199 9.2 9.7 9.7 828

16890 40.00 40.00 3.00 0.40 0.926 342.1 92.2 4608 16.4 56.6 2217 12.9 14.5 15.0 1026

16886 40.00 40.00 4.00 0.40 1.214 448.1 115.0 5752 16.0 72.5 2882 12.7 14.9 14.3 2389

16383 42.00 25.00 2.00 0.50 0.476 176.1 49.2 2344 16.7 10.9 627 7.9 7.5 8.4 235

16462 43.00 50.00 2.00 0.50 0.752 278.1 94.0 4374 18.4 74.0 2333 16.3 18.3 20.5 371

16567 43.76 19.06 1.50 0.75 0.320 118.6 34.1 1559 17.0 4.0 286 5.8 5.0 5.8 89

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number


A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

62


Hulam


atalogueAugust 2007

o90A

T1

T1

B

R1

y

y

x x

e

Cy

Centroid

16917 44.00 12.00 1.50 0.50 0.262 97.6 24.9 1133 16.0 1.1 115 3.3 2.7 2.7 73

160043 44.00 17.00 2.00 0.30 0.401 148.0 40.7 1850 16.6 3.7 297 5.0 4.4 4.5 197

16092 44.02 28.58 1.78 0.76 0.471 174.0 55.3 2514 17.8 14.5 732 9.1 8.7 10.1 184

160044 44.10 19.00 1.57 0.79 0.334 124.2 36.1 1637 17.0 4.2 297 5.8 5.0 5.7 102

16268 44.44 15.88 1.62 0.76 0.317 118.4 33.1 1491 16.7 2.6 215 4.7 3.9 4.3 103

16094 44.46 25.40 3.18 0.76 0.765 282.9 83.7 3765 17.2 17.3 993 7.8 7.9 7.6 953

16924 45.50 22.00 2.50 0.50 0.572 211.4 64.8 2848 17.5 9.5 606 6.7 6.3 6.4 440

16912 47.00 47.00 3.00 0.50 0.918 405.1 154.0 6552 19.5 93.5 3097 15.2 16.8 18.0 1215

16360 47.30 19.00 1.40 0.71 0.314 115.7 38.4 1624 18.2 3.8 269 5.8 4.7 5.7 75

16100 47.50 19.06 1.52 0.76 0.341 125.8 41.9 1764 18.2 4.2 292 5.8 4.8 5.7 97

16729 47.65 44.45 1.60 0.50 0.579 213.5 87.2 3660 20.2 45.2 1539 14.6 15.1 17.7 182

16332 48.51 12.70 1.60 0.80 0.305 113.4 34.9 1439 17.5 1.4 138 3.5 2.8 2.8 97

16423 48.90 19.06 1.80 0.50 0.406 150.3 52.1 2130 18.6 4.9 343 5.7 4.8 5.4 162

16106 48.90 19.06 2.04 0.76 0.456 169.4 58.1 2378 18.5 5.4 384 5.7 4.9 5.2 235

160052 49.40 54.85 3.00 0.50 1.244 459.4 197.9 8011 20.8 145.3 4179 17.8 20.1 21.7 1378

16811 50.00 20.00 1.25 0.63 0.296 109.5 41.0 1639 19.3 4.1 269 6.1 4.9 6.2 57

16588 50.00 25.00 1.50 0.50 0.394 145.6 57.2 2286 19.8 8.9 491 7.8 6.8 8.3 109

16451 50.00 30.00 3.00 0.40 0.845 312.1 120.9 4835 19.7 27.5 1327 9.4 9.3 9.6 936

160034 50.00 50.00 3.00 0.40 1.170 432.1 187.2 7489 20.8 113.2 3519 16.2 17.8 19.3 1296

160003 50.00 50.00 4.00 0.40 1.539 568.1 236.9 9474 20.4 146.2 4595 16.0 18.2 18.6 3029

16110 50.80 14.48 1.78 0.76 0.366 135.9 46.8 1841 18.5 2.2 198 4.0 3.3 3.3 143

16836 50.80 25.40 3.18 0.40 0.820 302.9 115.0 4528 19.5 18.1 1013 7.7 7.5 7.3 1021

16882 50.80 25.40 4.76 0.40 1.188 438.4 156.5 6162 18.9 24.9 1438 7.5 8.1 6.2 3310

16872 50.80 25.40 6.35 0.40 1.529 564.6 189.7 7469 18.3 30.7 1829 7.4 8.6 5.0 7588

160029 50.80 38.10 6.35 0.40 1.967 725.9 269.9 10627 19.3 100.0 4108 11.7 13.8 11.0 9755

16856 50.80 50.80 3.18 0.40 1.258 464.5 206.7 8139 21.1 125.4 3840 16.4 18.2 19.5 1565

16837 50.80 50.80 6.35 0.40 2.404 887.2 350.1 13785 19.9 226.5 7198 16.0 19.3 17.1 11923

16369 51.60 25.90 1.80 0.50 0.486 179.7 74.5 2887 20.4 11.8 627 8.1 7.2 8.5 194

16892 55.00 45.00 2.00 0.40 0.764 282.1 148.6 5404 23.0 60.5 1999 14.6 14.7 17.3 376

16869 55.00 50.00 2.00 0.40 0.818 302.1 162.7 5915 23.2 80.6 2435 16.3 16.9 19.7 403

16118 58.82 25.40 3.30 0.76 0.889 340.2 168.7 5735 22.3 19.5 1068 7.6 7.1 6.9 1234

16119 59.54 21.60 3.30 0.76 0.863 317.5 153.8 5167 22.0 12.3 775 6.2 5.8 5.1 1152

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number


A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

63


Hulam


atalogueAugust 2007

o90A

T1

T1

B

R1

y

y

x x

e

Cy

Centroid

16452 60.00 20.00 2.00 0.40 0.520 192.1 96.6 3221 22.4 6.5 425 5.8 4.7 5.3 256

16870 60.00 40.00 3.00 0.40 1.089 402.1 234.5 7818 24.2 65.2 2376 12.7 12.5 13.9 1206

16398 60.00 40.00 4.00 0.30 1.430 528.0 298.2 9940 23.8 83.8 3093 12.6 12.9 13.2 2816

16874 60.00 40.00 5.00 0.40 1.761 650.1 355.5 11849 23.4 101.0 3777 12.5 13.3 12.5 5417

16457 60.00 50.00 3.00 0.40 1.252 462.1 283.3 9444 24.8 120.7 3632 16.2 16.8 18.7 1386

16458 60.00 60.00 3.00 0.40 1.414 522.1 332.1 11070 25.2 198.9 5120 19.5 21.2 23.6 1566

16841 63.50 38.10 3.18 0.40 1.149 424.1 270.1 8508 25.2 61.1 2304 12.0 11.6 12.7 1429

160028 63.50 50.80 3.17 0.50 1.363 503.4 342.8 10795 26.1 135.2 3979 16.4 16.8 18.8 1686

16453 65.00 25.00 2.50 0.40 0.745 275.1 167.2 5145 24.7 15.2 817 7.4 6.4 7.0 573

16447 70.00 35.00 3.00 0.40 1.089 402.1 301.4 8612 27.4 47.3 1880 10.8 9.9 11.0 1206

16406 70.50 17.00 2.00 0.50 0.544 201.1 128.9 3657 25.3 4.2 313 4.6 3.5 3.7 268

160045 71.00 40.00 4.00 0.50 1.549 572.1 443.0 12479 27.8 88.7 3175 12.5 12.1 12.6 3051

160024 75.00 50.00 6.00 0.40 2.649 978.1 841.0 22428 29.3 238.4 7115 15.6 16.5 15.8 11736

16434 76.00 20.00 1.50 0.50 0.459 169.6 132.0 3475 27.9 5.3 334 5.6 4.0 5.1 127

16281 76.20 14.30 1.60 0.64 0.441 162.7 115.8 3039 26.7 2.1 182 3.6 2.6 2.7 139

16125 76.20 19.06 3.18 0.76 0.927 343.6 252.3 6621 27.1 8.8 600 5.1 4.4 3.5 1157

16322 76.20 25.40 2.50 0.76 0.826 305.2 248.0 6510 28.5 16.6 858 7.4 6.0 6.7 635

16248 76.20 25.40 3.18 0.64 1.037 383.8 306.0 8030 28.2 20.4 1067 7.3 6.3 6.3 1293

16126 76.20 38.10 3.18 0.64 1.258 464.6 413.7 10858 29.8 64.8 2366 11.8 10.7 12.1 1565

160030 76.20 38.10 4.76 0.40 1.843 680.2 581.2 15253 29.2 91.5 3411 11.6 11.3 11.0 5137

160039 76.20 38.10 6.36 0.40 2.407 888.4 728.2 19114 28.6 115.5 4396 11.4 11.8 9.8 11978

16127 76.20 44.46 3.18 0.64 1.367 505.0 467.6 12274 30.4 99.8 3186 14.1 13.1 15.1 1702

160038 76.20 50.80 3.18 0.40 1.477 545.2 521.3 13682 30.9 144.3 4111 16.3 15.7 18.1 1838

16880 76.20 50.80 6.35 0.40 2.841 1048.5 924.7 24269 29.7 262.7 7737 15.8 16.9 15.8 14091

16587 80.00 35.00 2.00 0.50 0.791 292.1 286.3 7158 31.3 34.2 1310 10.8 8.9 11.3 389

16879 86.00 40.00 3.00 0.40 1.300 480.1 541.6 12596 33.6 73.3 2504 12.4 10.7 12.6 1440

16875 88.00 50.00 3.00 0.40 1.479 546.1 680.1 15456 35.3 137.3 3859 15.9 14.4 17.2 1638

16597 90.00 20.00 3.00 0.50 1.008 372.1 375.5 8345 31.8 10.1 639 5.2 4.2 3.7 1116

16420 95.00 32.00 6.00 0.75 0.390 882.2 1047.9 22061 34.5 70.9 3038 9.0 8.7 6.5 10584

16343 97.25 19.00 1.50 0.50 0.537 198.5 235.5 4844 34.4 4.9 308 4.9 3.3 4.1 149

16876 100.00 40.00 3.00 0.40 1.414 522.1 772.5 15450 38.5 76.6 2553 12.1 10.0 12.0 1566

16877 100.00 50.00 5.00 0.40 2.574 950.1 1433.1 28661 38.8 225.0 6310 15.4 14.3 15.3 7917

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm

4

Zx

mm3

r

mm

Iy

x103mm

4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number


A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

Channel

64

Type 1 No radius(continued)

Hulam


atalogueAugust 2007

o90A

T1

T1

B

R1

y

y

x x

e

Cy

Centroid

16802 101.60 44.45 3.17 0.78 1.581 584.0 911.8 17948 39.5 108.8 3306 13.6 11.5 13.9 1955

16133 101.60 50.80 3.18 0.78 1.695 626.2 1012.2 19925 40.2 158.4 4289 15.9 13.9 16.8 2110

160032 101.60 50.80 6.00 0.40 3.108 1147.3 1754.5 34537 39.1 276.1 7690 15.5 14.9 14.9 13766

160051 101.60 50.80 8.00 0.60 3.635 1497.8 2203.0 43366 38.4 348.7 9909 15.3 15.6 13.4 31949

16302 102.40 15.88 2.00 0.76 0.728 260.6 319.5 6240 35.0 3.7 282 3.8 2.7 2.5 347

16801 102.40 44.45 3.17 0.78 1.644 586.6 928.7 18139 39.8 109.0 3309 13.6 11.5 13.9 1964

16911 104.00 42.00 2.00 0.50 0.997 368.1 604.0 11615 40.5 61.3 1923 12.9 10.1 13.5 491

160006 105.00 38.00 2.00 0.50 0.959 354.1 575.2 10956 40.3 46.5 1587 11.5 8.7 11.6 472

16878 106.00 40.00 3.00 0.40 1.463 540.1 886.9 16734 40.5 77.9 2571 12.0 9.7 11.8 1620

16135 111.24 38.10 4.56 0.76 2.208 813.4 1394.5 25073 41.4 98.8 3448 11.0 9.4 9.7 5636

16865 120.00 45.00 10.00 0.40 5.149 1900.1 3563.5 59392 43.3 305.3 9627 12.7 13.3 8.6 63333

16570 125.00 45.00 3.18 0.80 1.797 663.7 1505.5 24089 47.6 119.8 3483 13.4 10.6 13.2 2236

160041 127.00 34.93 9.53 0.75 4.591 1694.7 3301.3 51988 44.1 140.7 5588 9.1 9.8 4.3 51297

16140 139.70 18.26 2.38 0.64 1.097 408.3 897.9 12855 46.9 6.9 447 4.1 2.9 2.5 770

16863 140.00 60.00 8.00 0.40 5.289 1952.1 5458.2 77975 52.9 623.1 14419 17.9 16.8 16.0 41643

160040 152.40 76.20 4.76 0.40 3.809 1405.6 5111.9 67085 60.3 800.2 14448 23.9 20.8 25.3 10615

16556 158.75 50.80 3.18 0.80 2.190 808.0 2894.5 36466 59.9 179.8 4530 14.9 11.1 14.5 2723

160016 175.00 45.00 2.25 sharp 1.588 586.1 244.0 27888 64.52369 94.9 2600 12.7 8.5 12.1 989

16868 180.00 64.00 4.00 0.40 3.252 1200.1 5662.3 62914 68.7 439.9 8941 19.1 14.8 19.0 6400

16563 210.00 30.00 3.00 0.76 2.147 792.2 4053.3 38603 71.5 39.3 1546 7.0 4.6 4.9 2376

Shear

Centre

e

mm

J

mm4

Cy

mm

r

mm

Ix

x103mm4

Zx

mm3

r

mm

Iy

x103mm4

B

mm

T1

mm

R1

mm

Zy

mm3

Torsion

ConstantProfile

Number


A

mm

Mass

kg/m

Area

mm2

Prev

Next

Pg 5

Type 2 No radiusChannel

65

x

o90A

T2

T1

B

R1

y

y

x

e

Cy

Hulam


atalogueAugust 2007

Centroid

16806 8.50 22.00 2.00 1.50 0.75 0.207 77.2 0.9 200 3.3 3.7 302 6.9 9.7 8.5 68

16148 15.88 23.02 8.74 3.96 0.64 0.682 252.1 7.1 892 5.3 14.8 1196 7.7 10.6 2.5 4125

16150 25.40 22.22 3.18 1.60 0.64 0.385 141.9 13.0 1024 9.6 6.8 440 6.9 6.7 5.8 324

16460 40.00 20.20 8.00 8.00 0.50 1.395 515.3 93.7 4685 13.5 16.5 1333 5.7 7.8 1.7 10991

160033 88.90 38.10 6.36 7.93 0.50 2.896 1068.9 1200.2 27002 33.5 133.0 5054 11.2 11.8 10.0 18175

Shear

Centre

e

mm

T2

mm

J

mm4

Cy

mm

Zy

mm3

r

mm

Ix

x103mm

4

Zx

mm3

R1

mm

r

mm

Iy

x103mm

4

Mass

kg/m

Area

mm2

Torsion

ConstantProfile

Number


A

mm

B

mm

T1

mm

Prev

Next

Pg 5

Centroid

16303 16.36 15.68 1.60 1.60 3.00 0.76 0.202 74.8 3.2 388 6.5 1.8 179 4.9 5.5 5.3 61

160019 47.63 34.93 3.18 3.18 3.18 0.50 0.969 357.6 130.2 5468 19.1 43.7 1863 11.1 11.5 11.8 1191

16443 50.80 25.40 3.30 3.30 2.54 0.60 0.856 316.1 119.7 4711 19.5 18.7 1044 7.7 7.5 7.1 1138

16197 50.80 31.75 6.35 6.35 3.18 0.64 1.760 649.3 231.2 9102 18.9 59.1 2859 9.5 11.1 7.9 8671

16178 63.50 26.18 3.18 3.18 1.58 0.67 0.936 349.1 201.7 6354 24.0 21.1 1104 7.8 7.1 7.1 1174

16386 64.00 35.00 2.00 2.00 1.00 0.50 0.704 260.3 170.9 5340 25.6 31.9 1268 11.1 9.9 12.0 347

160013 72.22 35.00 3.18 3.18 3.18 0.64 1.181 436.2 345.5 9567 28.1 50.3 1989 10.7 9.7 10.7 1456

16184 88.90 53.98 6.36 6.36 6.36 0.64 3.215 1188.3 1429.2 32154 34.7 331.1 8953 16.7 17.0 16.4 15791

16185 94.60 22.45 1.75 1.75 1.60 0.63 0.653 238.9 281.5 5952 34.3 8.9 491 6.1 4.3 5.4 243

16525 101.60 50.80 3.96 4.74 14.28 0.64 2.536 933.7 1550.4 30520 40.7 230.1 6313 15.7 14.4 15.1 5429

160022 101.60 50.80 6.35 7.94 9.15 0.50 3.759 1386.9 2166.6 42650 39.5 326.7 9344 15.3 15.8 15.1 23505

16293 104.02 48.00 8.00 11.43 1.58 0.76 4.865 1747.4 2721.4 52324 39.5 344.4 10654 14.0 15.7 13.4 57573

16236 127.00 50.80 6.36 7.96 9.14 0.64 4.200 1550.9 3698.1 58237 48.8 351.0 9676 15.0 14.5 14.1 25833

16158 127.00 63.50 6.36 9.52 10.66 0.64 5.268 1944.3 4977.5 78386 50.6 732.1 16910 19.4 20.2 20.8 43758

16266 130.00 60.00 4.00 6.00 6.00 0.76 3.270 1207.2 3368.1 51816 52.8 426.1 10189 18.8 18.2 21.0 10837

16566 150.00 35.00 10.00 25.00 11.10 0.80 7.594 2802.6 7879.7 105063 53.0 162.9 6442 7.6 9.7 6.2 310417

16235 152.40 50.80 6.36 7.96 9.14 0.64 4.637 1712.4 5726.3 75149 57.8 370.4 9918 14.7 13.5 13.3 28011

16159 152.40 63.50 6.36 7.92 10.66 0.64 5.215 1923.0 6815.5 89443 59.5 706.5 15493 19.2 17.9 18.9 31993

16289 152.40 76.20 6.36 9.52 12.18 0.64 6.401 2362.5 8933.2 117233 61.5 1313.4 25111 23.6 23.9 25.8 53241

16524 152.40 76.20 9.52 12.70 12.20 0.62 8.694 3208.2 11330.4 148693 59.4 1697.6 32638 23.0 24.2 23.2 134888

16539 177.80 50.80 6.36 9.52 9.14 0.76 5.455 2012.6 9188.8 103361 67.6 421.8 11245 14.5 13.3 13.5 40809

16000 177.80 76.20 6.34 11.12 12.20 0.62 7.437 2744.7 14136.5 159016 71.8 1491.4 28315 23.3 23.5 26.0 79144

16234 177.80 88.90 7.92 12.70 13.72 0.64 9.620 3545.7 18186.5 204572 71.6 2649.2 43880 27.3 28.5 30.4 140029

16598 203.00 89.00 9.52 14.28 14.28 0.64 11.774 4289.9 27504.5 270980 80.1 3096.2 50114 26.9 27.2 28.0 212678

16541 203.20 65.02 11.84 11.84 12.70 0.80 10.100 3734.1 20343.3 200229 73.8 1205.5 25125 18.0 17.0 12.7 171269

16001 203.20 76.20 7.14 11.10 7.14 0.62 8.144 3005.7 19323.6 190193 80.2 1595.0 29448 23.0 22.0 24.4 87620

160023 203.20 76.20 9.52 12.70 12.20 0.64 10.000 3691.8 22518.7 221641 78.1 1859.9 34091 22.4 21.6 21.4 149498

Shear

Centre

e

mm

T2

mm

R1

mm

Ix

x103mm4

Zx

mm3

r

mm

Iy

x103mm4

Mass

kg/m

Area

mm2

R2

mm

J

mm4

Cy

mm

Zy

mm3

r

mm

Torsion

ConstantProfile

Number


A

mm

B

mm

T1

mm

Type 3 With radiusChannel

66

o90A

T2

T1

B

R1

R1

y

y

x x

e

Cy

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

I - Sections

67 y

y

x x

o90A

B

R1

R3

R2

T2

T1

T1

17010 9.52 9.57 1.60 2.39 0.76 0.76 0.224 45.2 0.5 110 3.4 0.2 46 2.2 55

17401 9.53 17.48 1.60 1.60 0.64 0.64 0.179 65.7 0.9 192 3.7 1.4 157 4.6 56

17211 13.50 22.00 1.75 1.75 0.40 0.40 0.256 94.4 2.8 417 5.5 3.1 280 5.7 96

17068 15.62 6.36 1.02 1.02 0.50 0.50 0.072 26.6 0.9 114 5.8 0.0 13 1.2 9

17108 15.88 15.88 1.60 0.76 0.80 0.76 0.191 59.8 2.7 339 6.7 1.0 126 4.1 45

17131 16.60 19.06 1.30 1.30 0.60 0.25 0.183 67.2 3.2 382 6.9 1.4 152 4.6 38

17110 19.52 19.52 1.26 1.26 0.50 0.50 0.191 70.4 4.6 472 8.1 1.5 156 4.7 37

17123 21.00 21.00 1.20 1.20 0.60 0.30 0.195 72.2 5.5 527 8.8 1.8 170 5.0 35

17515 22.00 22.00 3.00 2.00 0.90 0.90 0.444 163.3 12.6 1146 8.8 5.2 470 5.6 439

17043 23.24 22.98 1.40 1.40 0.76 0.76 0.251 92.5 8.6 741 9.7 2.7 236 5.4 61

17204 25.00 35.00 1.50 1.50 0.75 0.20 0.331 137.1 15.7 1257 10.7 10.4 596 8.7 104

17106 31.75 22.23 3.02 3.17 1.59 0.79 0.648 212.0 31.5 1984 12.2 5.1 459 4.9 681

17207 32.00 20.00 1.50 1.50 0.50 0.50 0.280 103.3 17.0 1060 12.8 2.0 197 4.4 78

17107 44.83 27.50 1.50 1.50 0.30 0.30 0.406 145.2 47.8 2135 18.2 5.2 377 6.0 109

17528 48.00 50.00 2.00 2.00 4.00 0.50 0.775 260.7 105.9 4413 20.2 26.0 1040 10.0 384

17408 48.50 27.40 2.00 2.00 0.64 0.64 0.539 198.2 73.8 3042 19.3 6.8 493 5.8 265

17022 48.90 19.06 2.04 2.04 0.76 0.76 0.457 168.7 57.7 2361 18.5 2.3 241 3.7 235

17209 49.00 78.00 2.00 2.00 1.00 0.50 1.085 400.5 186.8 7623 21.6 155.6 3991 19.7 536

17102 50.00 65.00 5.00 5.00 1.50 4.00 2.330 859.9 360.1 14406 20.5 225.6 6941 16.2 7083

17411 50.80 50.80 3.18 3.18 0.15 3.18 1.282 473.0 210.7 8295 21.1 69.7 2743 12.1 1565

17514 51.40 150.00 6.00 6.00 1.50 1.50 5.709 2034.5 962.2 37440 21.7 3354.2 44723 40.6 24437

17415 57.20 25.40 1.60 1.60 0.76 0.50 0.452 166.9 83.2 2910 22.3 4.2 333 5.0 143

17071 63.50 44.46 3.18 3.18 0.64 3.18 1.281 472.4 313.0 9858 25.7 46.5 2091 9.9 1566

17206 71.00 44.00 2.10 1.60 0.50 0.50 0.809 291.5 258.9 7292 29.8 29.6 1347 10.1 363

17127 75.60 19.70 1.30 1.30 0.20 0.20 0.396 146.1 112.8 2984 27.8 1.7 169 3.4 82

17208 76.00 20.00 1.50 1.50 0.50 0.50 0.459 169.3 131.6 3463 27.9 2.0 198 3.4 127

17502 120.00 120.00 10.00 10.00 1.00 7.00 9.323 3440.3 8207.0 136783 48.8 2885.3 48089 29.0 113333

17013 127.00 76.20 9.52 6.36 0.64 9.40 6.004 2212.6 5886.1 92695 51.6 709.7 18628 17.9 53088

17529 130.00 50.00 6.00 4.00 0.40 4.00 2.942 1085.5 2901.2 44634 51.7 125.7 5029 10.8 9717

17073 130.00 100.00 5.00 5.00 0.76 5.00 4.392 1620.5 4698.9 72291 53.8 832.7 16655 22.7 13333

17527 150.00 150.00 3.80 3.80 0.50 3.00 4.576 1688.4 7043.6 93915 64.6 2135.8 28478 35.6 8092

17098 150.00 150.00 10.00 12.00 8.00 1.00 13.320 4451.0 16390.5 218540 60.7 5059.2 67456 33.7 174880

J

mm4

r

mm

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

R2

mm

Mass

kg/m

Area

mm2

Ix

x103mm

4

B

mm

T1

mm

T2

mm

R1

mm

Torsion

ConstantProfile

Number


A

mm

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

I - Sections - continued

68

17069 152.40 101.60 6.36 6.36 0.78 0.78 5.899 2180.2 8336.4 109402 61.8 1112.0 21890 22.6 29403

17092 177.80 101.60 9.54 9.54 0.76 0.76 9.356 3452.2 16910.2 190216 70.0 1676.5 33002 22.0 104746

17507 177.80 101.60 11.50 7.94 1.50 11.50 9.760 3675.6 19246.8 216500 72.4 2021.2 39788 23.5 128843

17087 177.80 101.60 12.70 12.70 0.76 0.76 12.249 4515.6 21362.6 240299 68.8 2243.4 44161 22.3 242802

17091 203.20 101.60 11.12 7.94 0.80 11.43 10.320 3807.5 25644.0 252401 82.1 1962.6 38634 22.7 123330

J

mm4

r

mm

Zx

mm3

r

mm

Iy

x103mm

4

Zy

mm3

R2

mm

Mass

kg/m

Area

mm2

Ix

x103mm

4

B

mm

T1

mm

T2

mm

R1

mm

Torsion

ConstantProfile

Number


A

mm

o90A

B

R1

R3

R2

T2

T1

T1

y

y

x x

Hulam


atalogueAugust 2007

Prev

Next

Pg 5

Type 1 No radiusT - Sections

69

Centroid

14518 15.00 15.00 1.50 0.40 0.115 42.8 1.2 0.1 0.2 0.4 0.1 0.1 4.7 36

14005 19.06 19.06 3.18 0.64 0.300 111.1 5.3 0.4 0.2 1.9 0.2 0.1 6.8 419

14538 20.00 11.25 1.25 0.50 0.103 37.5 2.2 0.2 0.2 0.2 0.0 0.1 7.3 22

14214 20.00 20.00 1.50 0.40 0.159 57.8 3.0 0.2 0.2 1.0 0.1 0.1 5.9 49

14006 22.04 46.06 3.00 0.20 0.530 195.3 13.4 0.8 0.3 24.5 1.1 0.4 5.2 656

14116 22.20 22.20 2.00 0.25 0.229 84.8 5.4 0.4 0.3 1.8 0.2 0.1 6.8 127

14108 22.20 22.20 3.00 0.50 0.337 124.2 8.0 0.5 0.3 2.8 0.3 0.1 7.5 417

14013 22.22 45.24 3.18 0.64 0.553 204.4 14.2 0.8 0.3 24.6 1.1 0.3 5.4 772

14117 25.00 25.00 1.60 0.30 0.209 77.4 6.3 0.4 0.3 2.1 0.2 0.2 7.3 74

14017 25.40 25.40 3.18 0.64 0.409 151.4 12.7 0.7 0.3 4.4 0.3 0.2 8.4 572

14085 25.40 31.75 1.28 0.38 0.120 71.5 6.0 0.3 0.3 3.4 0.2 0.2 6.4 44

14019 25.40 38.10 3.18 0.64 0.520 191.8 16.3 0.9 0.3 14.7 0.8 0.3 6.9 724

14091 25.40 44.45 3.18 0.20 0.574 212.0 18.5 1.0 0.3 23.3 1.0 0.3 6.4 800

14511 30.00 30.00 3.00 0.40 0.463 171.0 20.0 1.0 0.3 6.8 0.5 0.2 9.4 575

14215 35.00 35.00 3.00 0.40 0.544 201.0 31.9 1.3 0.4 10.8 0.6 0.2 10.6 675

14032 38.10 12.70 1.14 0.50 0.153 56.6 13.8 0.6 0.5 0.2 0.0 0.1 15.2 27

14067 38.10 38.10 2.38 0.80 0.475 175.7 33.1 1.2 0.4 11.0 0.6 0.3 11.0 372

14536 38.10 38.10 6.35 0.76 1.201 443.5 84.1 3.4 0.4 29.9 1.6 0.3 13.6 6677

14068 38.45 38.45 3.20 0.63 0.629 235.8 45.2 1.7 0.4 15.3 0.8 0.3 11.6 902

14121 40.00 20.00 3.00 0.20 0.463 171.0 41.4 1.7 0.5 2.1 0.2 0.1 15.5 575

14209 40.00 40.00 3.00 0.40 0.626 231.0 47.9 1.7 0.5 16.1 0.8 0.3 11.9 776

14512 40.00 40.00 4.00 0.40 0.823 304.0 63.1 2.3 0.5 21.5 1.1 0.3 12.5 1816

14128 42.00 42.00 2.00 0.50 0.444 164.0 37.5 1.2 0.5 12.4 0.6 0.3 11.8 245

14096 50.00 25.00 3.00 0.80 0.584 216.0 81.0 2.6 0.6 4.0 0.3 0.1 18.9 726

14506 50.00 50.00 4.00 0.40 1.040 384.0 124.5 3.6 0.6 41.9 1.7 0.3 15.0 2294

14520 50.80 31.75 6.35 0.30 1.311 483.9 179.9 5.9 0.6 17.9 1.1 0.2 20.1 7284

14500 50.80 50.80 3.18 0.40 0.848 313.0 104.8 2.9 0.6 34.9 1.4 0.3 14.7 1182

14507 60.00 60.00 4.00 0.40 1.257 464.0 216.7 5.1 0.7 72.3 2.4 0.4 17.5 2772

14508 60.00 60.00 6.00 0.40 1.853 684.0 319.6 7.8 0.7 109.0 3.6 0.4 18.8 9193

14529 76.20 76.20 6.36 0.40 2.517 928.8 699.6 13.2 0.9 236.0 6.2 0.5 23.1 14026

14505 100.00 60.00 5.00 0.40 2.100 775.0 1095.7 16.8 1.2 91.0 3.0 0.3 34.8 7233

J

mm4

Mass

kg/m

R1

mm

Profile

NumberA

mm

Torsion

Constant

Area

mm2

Ix

x103mm4

Zx

mm3

B

mm

T

mm


r

mm

Cx

mm

r

mm

Iy

x103mm4

Zy

mm3

Hulam


atalogue

o90

A

B

T

T

R1Cx

x

y

y

x

August 2007

Prev

Next

Pg 5

Type 2 With radius

70

T - Sectionso90

A

B

T

T

R1

R2

Cx

x

y

y

x

Centroid

14408 19.00 15.87 2.36 1.60 0.75 0.225 77.8 3.7 0.3 0.2 0.8 0.1 0.1 6.7 160

14103 30.00 20.00 2.00 0.50 1.00 0.221 96.1 12.0 0.6 0.4 1.4 0.1 0.1 10.4 143

14524 32.00 75.00 6.00 3.00 0.50 1.652 609.9 91.1 3.8 0.4 211.4 5.6 0.6 8.1 8145

14415 38.10 38.10 1.22 1.145 0.79 0.252 92.0 17.3 0.6 0.4 5.7 0.3 0.2 10.2 51

14047 38.10 38.10 4.78 5.84 0.64 0.964 356.0 67.1 2.6 0.4 23.4 1.2 0.3 12.2 2912

14202 38.10 50.80 6.36 3.00 0.50 1.425 528.8 99.9 3.8 0.4 70.3 2.8 0.4 11.9 7927

14531 50.00 75.00 5.00 6.00 0.40 1.668 615.5 204.5 5.5 0.6 177.5 4.7 0.5 12.7 5600

14532 50.00 100.00 5.00 6.00 0.40 2.006 740.5 261.2 6.7 0.6 418.0 8.4 0.8 11.0 6767

14530 50.80 50.80 6.00 5.00 0.40 1.583 584.3 195.7 5.7 0.6 67.6 2.7 0.3 16.3 7709

14050 50.80 50.80 6.36 6.36 0.64 1.687 623.1 208.7 6.1 0.6 72.6 2.9 0.3 16.4 9147

14112 56.00 38.00 4.00 1.00 10.00 1.039 360.4 155.7 4.3 0.7 18.6 1.0 0.2 19.4 2150

14522 60.00 86.00 6.00 3.00 0.80 2.050 843.9 399.3 9.0 0.7 319.4 7.4 0.6 15.8 11290

14052 63.50 63.50 6.36 6.36 0.64 1.687 784.6 410.1 9.3 0.7 140.4 4.4 0.4 19.6 11587

14523 65.00 100.00 8.00 3.00 0.50 3.413 1259.9 705.2 14.8 0.7 669.5 13.4 0.7 17.4 30010

14129 70.00 80.00 3.18 3.18 0.50 1.276 471.2 299.6 5.8 0.8 136.8 3.4 0.5 18.1 1763

14502 76.00 76.00 6.50 7.00 0.50 2.619 966.8 723.5 13.6 0.9 245.5 6.5 0.5 22.7 14918

14533 76.20 152.40 9.50 9.52 1.00 5.743 2120.3 1731.5 29.7 0.9 2811.8 36.9 1.2 17.8 70131

14043 99.40 51.30 3.15 0.82 0.82 1.258 465.1 672.8 10.5 1.2 36.0 1.4 0.3 35.0 1722

14503 102.00 102.00 6.50 7.00 0.50 3.535 1304.8 1759.3 24.2 1.2 588.4 11.5 0.7 29.2 20249

14058 127.00 101.60 9.52 9.90 0.76 5.764 2127.7 4543.7 52.8 1.5 884.2 17.4 0.6 40.9 70568

14097 152.40 76.20 9.50 9.52 1.00 5.749 2120.3 7285.9 76.3 1.9 449.2 11.8 0.5 56.9 70131

J

mm4

Mass

kg/m

R2

mm

Profile

NumberA

mm

Torsion

Constant

Area

mm2

Ix

x103mm

4

Zx

mm3

B

mm

T

mm

Dimensions

R1

mm

X-X Axis Y-Y Axis

r

mm

Cx

mm

r

mm

Iy

x103mm

4

Zy

mm3

Hulam


atalogueAugust 2007

Prev

Pg 5

Next


Index

Die Nr Pg

11 2712 2733 4676 27229 27282 27736 462894 2710005 3310015 3310022 3310023 3310024 3310027 3310036 3310042 3310043 3310044 3310045 3410074 3410076 3410081 3510094 3510095 3510096 3510097 3510104 3510105 3510106 3510114 3610118 3610122 3610132 3610142 3610157 3610167 3510209 3510216 3510229 3310231 3310248 3310249 3310250 3310251 3310253 3310265 3410267 3410270 3410273 3410279 3410280 3410286 3410289 3410319 3410321 3510324 3510351 3610358 3510360 3510363 3310365 35

Die Nr Pg

10369 3410378 3310387 3410397 3610399 3410409 3510429 3310449 3410465 3310469 3310477 3310490 3410492 3610493 3410503 3310504 3310509 3310512 3410515 3310516 3310517 3310531 3410533 3310534 3310535 3410536 3510537 3310538 3410539 3510540 3410541 3410542 3410544 3410546 3310547 3310548 3310550 3410551 3410552 3410553 3410555 3410558 3310559 3310560 3310561 3310562 3410563 3410564 3410565 3410566 3410567 3310568 3310569 3310570 3310573 3310575 3410577 3310578 3410579 3310704 3510726 35

Die Nr Pg

10730 3310740 3410777 3510791 3510809 3310829 3410921 3510925 3410941 3510946 3510958 3410979 3514005 4514006 4514013 4514017 4514019 4514032 4514043 4614047 4614050 4614052 4614058 4614067 4514068 4514085 4514091 4514096 4514097 4614103 4614108 4514112 4614116 4514117 4514121 4514128 4514129 4614202 4614209 4514214 4514215 4514408 4614415 4614500 4514502 4614503 4614505 4514506 4514507 4514508 4514511 4514512 4514518 4514520 4514522 4614523 4614524 4614529 4514530 4614531 4614532 46

Die Nr Pg

14533 4614536 4514538 4515000 1715002 2015010 2015011 2015012 2015013 2015016 2015017 2015018 2015024 2015025 2015027 2015028 2015038 1715039 1715040 1715041 1715042 1715043 1715050 1715051 1715057 1715058 1715059 1715061 1715064 1815065 1815067 1815073 1815075 1815078 1815083 1915085 1915086 1915087 1915096 1615102 1515103 1515104 1515110 1615111 1615112 1615113 1615118 1615119 1615121 1615122 1615123 1615125 1615127 1615128 1615130 1615132 1615135 1615137 1515139 1515145 1515147 15

Die Nr Pg

15148 1515150 1515155 1515158 1515163 1515165 1515170 1515172 1515174 1515176 1515178 1515181 1515192 1515193 1515207 1515209 1515210 1515214 2015216 2015225 2015228 2015231 2015234 1615241 1715248 1815252 1915255 1715258 1715262 1815263 1915264 1715271 2015272 2015286 1615287 1615290 1915291 1515294 1615295 2115297 1515308 1815322 1715323 2115327 2015333 2015339 1815341 2015347 1715348 1815349 1615350 2015355 1915356 1915359 1515361 1815363 1515364 1915372 1515373 1515374 1815375 18

Die Nr Pg

15376 1715408 1715411 1715412 1715420 1515421 1915433 2115441 1715455 1915457 2015463 1715474 2015479 1615485 1515504 1915506 1515515 2015517 1815518 1915519 1915520 1815522 1815523 1815524 1915526 1515527 1515529 1515530 1515532 1515540 1515543 1615544 1615545 1615546 1615547 1615554 1515555 1515556 1515557 1515558 1715559 1715561 1715562 1715563 1515564 1815565 1515567 1715569 1915570 1815571 1815572 1515574 1515575 1515576 1715578 1515579 1515581 1715582 1815585 1515708 1515713 15

Die Nr Pg

15731 1715733 1515735 1515736 1515810 1615811 1615813 1615816 2015819 2015821 1515823 1515824 1515825 1515826 1515827 1515828 1515829 1515830 1515831 1515832 1515833 1515834 1515836 1715837 1715838 1715839 1815840 1815841 1815842 1915843 1915844 1915845 1715846 2015847 2015849 1815850 1915851 1615852 2015854 1515856 1515857 1815858 1915859 1515860 1515861 1515862 1515863 1915870 1915871 1515872 1515875 1715876 1715877 1815878 1915879 1515880 1515881 1515882 1715885 1715886 1715887 19

Prev

Next

Pg 5


Die Nr Pg

15888 1815890 1515891 1715892 1815893 1815894 1815899 1815900 1915901 1515902 1815903 1815905 1515906 1515907 1515908 1515909 1715913 1515919 1915920 1915922 1515923 1815924 1815925 1915926 1715927 1815928 1715929 1815931 1715932 1815933 1815934 1915936 1915937 1815939 1515940 1515942 1915943 1915944 1915947 1515949 1615950 1715952 1915953 1815954 1815956 1815958 1915959 1815962 1915963 2015964 1615966 1615969 1915970 1515971 1915972 1515976 1815977 1915980 1515983 1915984 1515985 17

Die Nr Pg

15986 1715987 1815988 1915989 1815990 1615991 2015992 1515993 1515994 1515995 1515996 2115999 1816000 2616001 2616007 2216008 2216009 2216016 2216018 2216020 2216022 2216026 2216027 2216031 2216032 2216041 2216043 2216048 2316056 2316059 2316061 2316066 2316067 2316069 2316072 2316077 2316079 2316092 2316094 2316100 2316106 2416110 2416118 2416119 2416125 2416126 2416127 2416133 2516135 2516140 2516148 2516150 2516158 2616159 2616178 2616184 2616185 2616197 2616220 2216223 2216234 26

Die Nr Pg

16235 2616236 2616246 2716248 2416254 2316255 2316256 2616266 2616267 2616268 2316281 2416289 2616293 2616302 2516303 2616322 2416326 2716327 2716332 2416339 2316340 2716341 2216343 2416348 2216354 2316357 2216360 2316369 2416372 2316383 2316384 2316386 2616389 2316395 2216396 2216398 2416406 2416408 2316412 2616417 2216420 2416421 2216423 2416426 2316428 2216430 2216434 2416435 2616442 2616443 2616444 2216445 2216446 2216447 2416448 2216449 2316450 2316451 2416452 2416453 2416457 24

Die Nr Pg

16458 2416459 2616460 2516461 2616462 2316463 2316464 2216465 2216466 2216470 2216472 2216473 2216475 2616476 2316500 2216502 2216505 2216518 2616522 2616524 2616525 2616530 2316539 2616541 2616556 2516563 2516566 2616567 2316568 2716570 2516583 2616587 2416588 2416589 2716597 2416598 2616710 2216729 2416801 2516802 2516806 2516811 2416817 2616824 2216825 2216826 2316827 2316828 2316830 2316832 2316833 2316834 2316836 2416837 2416841 2416849 2716856 2416857 2216860 2716861 2716863 25

Die Nr Pg

16865 2516867 2216868 2516869 2416870 2416872 2416874 2416875 2416876 2416877 2516878 2516879 2416880 2416881 2316882 2416884 2716885 2216886 2316887 2216889 2316890 2316892 2416895 2216900 2716902 2216907 2216910 2716911 2516912 2316917 2316919 2216923 2216924 2316926 2716927 2316930 2716942 2717010 4417013 4417022 4417043 4417068 4417069 4417071 4417073 4417087 4417091 4417092 4417098 4417102 4417107 4417108 4417110 4417123 4417127 4417128 4617131 4417206 4417207 4417208 4417209 44

Die Nr Pg

17211 4417401 4417408 4417411 4417415 4417502 4417507 4417514 4417515 4417527 4417528 4417529 4438101 3738396 4638397 4638398 4639955 37101113 35101115 35101122 35101123 34101124 34101126 34101127 33101128 34101129 34101130 34101131 33101132 33101134 33101135 33101136 33101137 34101138 34101139 34101140 34101141 34101142 34101144 35101145 35101146 35101147 35101148 35101149 35101151 34101152 34101153 34101154 34101155 33101156 34101157 34101158 33101159 34101162 33101164 33101165 33101166 34101167 33101168 34101169 33101170 35

Die Nr Pg

101171 35101173 34101175 33101176 33101177 33101178 33101179 33101180 33101181 33101182 33101183 33101184 33101185 33101186 34101187 34101188 34101189 34101190 35101191 33101192 33101194 33101199 36101200 35101202 35101203 33101204 33101206 35101207 35101208 35101209 33101211 33101212 33101213 33101214 35101217 34101218 33101221 34101224 33101228 34101229 34101231 35101234 35101235 33101236 35101237 35101238 34101240 34101243 33101244 33101245 34101258 33101261 33101264 33101265 33101266 34101267 34101268 34101269 34101270 33101272 34101273 33

Index

Prev

Next

Pg 5


Index

Die Nr Pg

101274 33101279 35101281 36101282 35101286 34101289 35101298 34101300 34101306 34101307 36101313 33101317 34101326 37101332 34101335 34101504 33101508 33101516 36101518 36101524 34101527 35101528 35101537 33101546 33101547 33101551 33101555 34101560 34101563 34101571 35101572 34101573 34101574 34101575 33101577 35101578 34101581 35101583 35101585 33101586 33101587 34101588 33101589 34101591 35101592 33101593 33101594 35101595 35101596 33101597 35101598 34101599 34101602 35101606 34101607 34101608 34101609 34101613 34101624 34101628 34101630 35

Die Nr Pg

101640 35101649 34150000 15150001 17150002 17150003 15150004 15150005 15150006 19150007 15150008 19150010 18150012 18150014 15150015 19150017 19150019 15150020 15150021 15150025 18150027 17160002 23160003 24160006 25160013 26160014 23160016 25160019 26160022 26160023 26160024 24160026 22160027 22160028 24160029 24160030 24160032 25160033 25160034 24160035 23160036 23160037 22160038 24160039 24160040 25160041 25160042 22160043 23160044 23160045 24160051 25160052 24H0006 40H0007 39H0012 42H0041 42H0102 38H0175 42H0247 39H0256 43H0315 42

Die Nr Pg

H0363 42H0454 40H0532 39H0637 40H0668 40H0803 40H0823 42H1358 40H1485 38H1561 38H1568 38H1569 39H1639 40H1671 43H1673 43H1885 38H1978 39H2027 43H2045 39H2071 40H2105 42H2256 42H2268 43H2309 43H2497 38H2547 38H2564 42H2591 38H2961 40H3002 42H3012 43H3115 39H3121 42H3176 41H3197 40H3209 39H3303 38H3308 41H3523 39H3557 43H3576 40H3855 42H4026 40H4084 42H4091 38H4092 39H4125 38H4147 39H4205 38H4316 43H4318 38H4415 42H448 27H4488 40H4519 43H4520 40H4521 41H4522 40H4525 43H4570 42H4571 42

Die Nr Pg


Die Nr Pg


Die Nr Pg


Die Nr Pg

H8207 41H8228 43H8276 43H8339 38H8340 38H8341 38H8378 40H8430 42H8432 39H8433 39H8452 42

Prev

Next

Pg 5

Notes


Prev

Next

Pg 5


Notes

Prev

Next

Pg 5

www.hulaminextrusions.co.za

Prev

Next

Pg 5

Head Office and Midrand OperationTel: +27 (11) 206 0200Fax: +27 (11) 206 0206Address: Cnr Main & Olifantsfontein Road, Olifantsfontein.PO Box 25, Olifantsfontein. 1665 . South Africa

Pietermaritzburg Operation and Export Sales OfficeTel: +27 (33) 395 6911Fax: +27 (33) 395 6244 (Local Sales)

+27 (33) 394 7395 (Export Sales)Address: Edendale Road, Pietermaritzburg.PO Box 74, Pietermaritzburg. 3200. South Africa.

Cape Town OperationTel: +27 (21) 534 5531Fax: +27 (21) 535 0041Address: Bertie Avenue, Epping Industria 2, Cape Town.PO Box 160, Eppingdust. 7475. South Africa.

Southern Africa Enquiries: [email protected] Enquires: [email protected]: www.hulaminextrusions.co.za

Prev

Pg 5

mailto:[email protected]

mailto:[email protected]

http://www.hulaminextrusions.co.za

HulaminCatalogue.pdf

Documents

Transcript of HulaminCatalogue.pdf