High Flow Degasser
-
Upload
marcus-backman -
Category
Documents
-
view
243 -
download
3
description
Transcript of High Flow Degasser
everything for the lab
Biotech AB – your single provider of HPLC and fluidic scientific customized parts & assemblies
For ordering & informtion – Telephone +46 (0)300-56 91 80. Fax +46 (0)300-56 91 81. www.biotech.se2
Product Advance Sheet
Eastern Plastics I Innovadyne I Ismatec I Isolation Technologies I Rheodyne I Sapphire Engineering I Systec I Upchurch Scientific
IDEX Health & Science’s Systec® High-Flow Degasser is a non-porus, air-permeable membrane activated by a controlled vacuum source capable of removing dissolved air from liquids at a rate of up to one liter per minute in OEM instruments. The High-Flow Degasser is designed to degas liquids in high-throughput applications such as clinical chemistry analyzers to prevent bubble formation and improve dispense precision.
Accommodating a broad range of fluids including aqueous salts, organics, detergents, and sterilizing agents, the High-Flow Degasser incorporates the longest-life pump available on the market with membrane materials chosen to reduce maintenance and provide the lowest total cost of ownership.
Dispense Precision, Long Life f Removes dissolved gases and bubbles from fluidic lines to improve dispense precision
f Longest lifetime pump and membrane materials are selected to reduce maintenance and provide best TCO
f Compatible with broad range of fluids including aqueous salts, organics, detergents and sterilizing agents (pH range: 2–13)
f Highest efficiency membrane reduces unit size, which increases available benchtop space
f Tested and calibrated assembly is ready for installation
Systec®
High-Flow Degasser
Technical Data
Part Number 0001-6673 0001-6676
Operational flow rate(mL/min) 0–500 0–1,000
Pressure Drop(at 20 °C and max flow) < 1 kPa < 12 kPa
Internal Volume 45 mL 30 mL
Degassing Efficiency(removed O2% in DI water at max flow)
< 60 % < 60 %
Number of Channels 1 1
Maximum Operating Pressure 1 bar (15 psi) 1 bar (15 psi)
Maximum Temperature 40 °C 40 °C
Wetted Materials(membrane)
Polysulfone, silicone rubber, polypropylene, Tygon™ S-50-HL, medical grade adhesives
External Fluidic Ports 3/16 inch (4.8 mm) ID barb fittings
Expected Lifetime* > 6 years (continuous run at 100 rpm 12 hours/day 365 days/year)
*�Please contact factory for additional pump/lifetime options.
Tygon® is a registered trademark of Saint-Gobain Performance Plastics Corporation Teflon® is a registered trademark of E.I. du Pont de Nemours and Company,
used under license by Upchurch Scientific. Only DuPont makes Teflon®. Systec® is a registered trademark of IDEX Health & Science LLC
©2011 IDEX Health & Science LLC
IDX1353-PS-HS/6.2011
www.idex-hs.com I North/South America +1 866 339 4653 I Europe +49 1801 808 800 I Asia +86 10 6566 9090
Eastern Plastics I Innovadyne I Ismatec I Isolation Technologies I Rheodyne I Sapphire Engineering I Systec I Upchurch Scientific
Product Advance Sheet
6.1”155 mm
3/16" ID TUBE CONNECTION [ 4.8 mm ]
EXHAUST: 1/8" ID TUBE CONNECTION [ 3.2 mm ]
4.1”105 mm
3.9”100 mm
8.4”212 mm
3.5”89 mm
6.0”152 mm
1.25”31.8 mm
1.1”27 mm
7.5”191 mm
8.3”211 mm
6.1”155 mm
3/16" ID TUBE CONNECTION [ 4.8 mm ]
EXHAUST: 1/8" ID TUBE CONNECTION [ 3.2 mm ]
4.1”105 mm
3.9”100 mm
8.4”212 mm
3.5”89 mm
6.0”152 mm
1.25”31.8 mm
1.1”27 mm
7.5”191 mm
8.3”211 mm
Systec High-Flow Degasser
6.1”155 mm
3/16" ID TUBE CONNECTION [ 4.8 mm ]
EXHAUST: 1/8" ID TUBE CONNECTION [ 3.2 mm ]
4.1”105 mm
3.9”100 mm
8.4”212 mm
3.5”89 mm
6.0”152 mm
1.25”31.8 mm
1.1”27 mm
7.5”191 mm
8.3”211 mm
6.1”155 mm
3/16" ID TUBE CONNECTION [ 4.8 mm ]
EXHAUST: 1/8" ID TUBE CONNECTION [ 3.2 mm ]
4.1”105 mm
3.9”100 mm
8.4”212 mm
3.5”89 mm
6.0”152 mm
1.25”31.8 mm
1.1”27 mm
7.5”191 mm
8.3”211 mm
Pump Control Specifications
Power Requirements 24 VDC at 0.85 amp max. (0.5 amp typical)
International Power Adapter Included
AC adapter: 100–240 V AC, 1A, 50–60 Hz(for North America, UK, continental Europe, Japan, Australia)
Vacuum Sensor Calibration Accuracy
±5 mm Hg absolute over an ambient operating temperature range of 10–35 °C (NIST traceable)
Closed-Loop Control Setpoint
120 mm Hg absolute (pump runs at high rpm until near setpoint, then speed is varied to maintain a value of 120 mm Hg absolute — load independent)
LED IndicatorsSingle Bi-Color
Green - Blinking Vacuum reaches upper control range
Green - Solid Vacuum reaches control set point
Amber - Blinking Power on, vacuum operating normally
Amber - Solid Error condition, shutdown
Errors Detected
1 - PumpdownUnable to reach 120 mm Hg (16 kPa) in 10 minutes
2 - High VacuumVacuum > 200 mm Hg (26.7 kPa) for > 10 minutes
3 - Sensor SignalSensor > 800 mm Hg (106.7 kPa) or < 10 mm Hg (1.3 kPa)
Internal structure
For ordering & informtion – Telephone +46 (0)300-56 91 80. Fax +46 (0)300-56 91 81. www.biotech.se2
Biotech Sweden is a company highly specialized in chromato-
graphy accessories and consumables. Biotech is located on the
Swedish Westcoast – south of Gothenburg – at the beautiful
Onsala peninsula, covering 15.000 sq.m. land and 700 sq.m.
production and office area.
bioteChview from our office windows
Biotech AB. P.O. Box 133, SE-439 23 Onsala, Sweden.
Telephone +46 (0)300-56 91 80. Fax +46 (0)300-56 91 81
[email protected] – www.biotech.se
We at Biotech believe that value is not ”the lowest price” – our
customers are the reason we exist – our customers always come
first. We have not lost sight where we come from and therefore
we try harder to be your partner, we’re not satisfied unless you
are satisfied.
Thank you for your business. I know we’ll continue to grow
and prosper together.
a simple philosophy...
Affiliated companies: Biotech USA LLC
281 County Road C2W,
Roseville MN 55113, USA
Biotech India Pvt Ltd
Mumbai 400-099, India
Banking Reference: Handelsbanken
Kungsbacka Branch, Sweden
Fax +46 300 334 29
We accept visa® and masterCard® - no minimum order.