HERITAGE COUNCILheritagecouncil.vic.gov.au/.../Old-Cobram-Barooga-Bridge.doc · Web viewSchematic...

HERITAGE COUNCIL DETERMINATION

Determination Date 4 February 2016

Place/Object Name Old Cobram-Barooga Bridge

Location Vermont Street Cobram, Moira Shire

VHR Number H2352

Category Heritage Place

At a meeting of the Heritage Council of Victoria on 4 February 2016 it was determined that, in accordance with Section 42 of the Heritage Act 1995, the above place is of cultural heritage significance to the State of Victoria and warrants inclusion in the Victorian Heritage Register. This decision was reached having considered the assessment against the Heritage Council’s criteria, other information contained in the attached report and all submissions received in response to the Executive Director’s recommendation. The Heritage Council endorses and adopts the attached report for the purposes of making its decision.

Professor Stuart Macintyre AOChair, Heritage Council of Victoria

ASSESSMENT OF CULTURAL HERITAGE SIGNIFICANCE AND EXECUTIVE DIRECTOR RECOMMENDATION TO THE HERITAGE COUNCIL

Name: Old Cobram-Barooga BridgeHermes Number: 197955

Page | 1

NAME OLD COBRAM-BAROOGA BRIDGE

LOCATION VERMONT STREET COBRAM, MOIRA SHIRE

HERMES NUMBER: 197955

CATEGORY: HERITAGE PLACE

FILE NUMBER: FOL/15/48243

INCLUDEPICTURE "https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/800px-CobramBaroogaBridgeOld.JPG" \*

MERGEFORMATINET INCLUDEPICTURE "https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/800px-CobramBaroogaBridgeOld.JPG" \*









https://upload.wikimedia.org/wikipedia/commons/4/47/CobramBaroogaBridgeOld.JPG


MERGEFORMATINET

EXECUTIVE DIRECTOR RECOMMENDATION TO THE HERITAGE COUNCIL: That the Old Cobram-Barooga Bridge (the section in Victorian territory) be included as a

Heritage Place in the Victorian Heritage Register under the Heritage Act 1995 [Section 32 (1)(a)].

This is a joint registration made in partnership with the Heritage Council of New South Wales. It is anticipated that the New South Wales section of the Bridge will be registered in the New South Wales Heritage Register in mid-December 2015. There are currently four bridges over the Murray River jointly registered in each state’s heritage register.

TIM SMITHExecutive DirectorRecommendation Date: 13 November 2015



EXTENT OF NOMINATION

The section of the Old Cobram-Barooga Bridge which extends into Victorian territory.

RECOMMENDED REGISTRATION

All of the place shown hatched in Diagram 2352 encompassing part of Crown Allotment 7D Parish of Cobram.

The extent of registration of the Old Cobram-Barooga Bridge in the Victorian Heritage Register affects the whole place shown on Diagram 2352 including the land, roads, trees, landscape elements and other features.

AERIAL PHOTO OF THE PLACE SHOWING PROPOSED REGISTRATION

STATEMENT OF CULTURAL HERITAGE SIGNIFICANCE

WHAT IS SIGNIFICANT?

The Old Cobram-Barooga Bridge, consisting of a two-span de Burgh truss bridge with a central single, vertical-lift opening span supported on cast iron piers located on the former road that connects the border towns of Cobram (Victoria) and Barooga (New South Wales).

History Summary

Since the beginnings of European settlement, the waters of the Murray River have been a key factor in the commercial agricultural development of what has been some of the most productive land in modern Australia. During the mid-nineteenth century toll-ferries and row boats had a monopoly on transporting people and goods across the river. From 1889 a punt operated between Cobram and Barooga and was the only means of crossing the river at this point. In 1879 two bridges opened - the Murray Bridge (South Australia) and the Echuca-Moama Bridge. During the 1880s and 90s the colonial governments of New South Wales and Victoria began a joint program of building bridges with opening spans which could accommodate paddle steamers, trains and road traffic. The Old Cobram-Barooga Bridge was officially opened on 3 December 1902 and provided access for heavy goods vehicles to transport agricultural produce. The central lift-span of the bridge allowed paddle steamers to pass underneath. The bridge was constructed by the prolific Victorian bridge-building firm of JB and W Farquharson of Melbourne. The improved capacity to transport agricultural goods, particularly wool and wheat, to Melbourne, Sydney and larger regional towns consolidated the importance of north-eastern Victoria and the Riverina District of New South Wales. The Cobram Bridge is the only bridge on the Murray River whose construction was completely funded by the Victorian government. In 2002 a high level concrete bridge was built to the south of the original 1902 bridge, which remains open for pedestrian traffic.

Description SummaryThe Old Cobram-Barooga Bridge is a timber truss, lift-span bridge carrying two traffic lanes across the Murray River between Cobram and Barooga. The primary axis of the bridge is east-west. The bridge has a clearance over normal water level of 7.9m with the lift-span closed and 14.3m with the lift-span open. The bridge was superseded by a parallel concrete bridge and no longer carries vehicular traffic. The three main spans include a single, vertical-lift opening span supported on cast iron piers in the centre of the bridge, flanked by a single de Burgh Truss span on each side. The eastern (NSW) side has been truncated and retains only one timber beam approach span, which terminates in a steel fence and stair to ground level. All three timber beam approach spans survive on the western (Victorian) side. The outer ends of the truss spans and the approach spans are carried on timber trestles on timber piles. The outer ends of the lift-span are carried on twin cylindrical cast iron piers with intermediate perforated steel plate braces.

The lift-span is formed by a roadway between riveted Pratt-Truss box-girders with a span of 18m. The road deck on the lift-span is narrower than the approaches and reduces to one traffic lane. The lifting superstructure comprises four steel lattice towers, connected at their upper level by steel lattice girders. The two de Burgh truss spans, each 31.7m, are of composite timber and steel construction, with paired timber top chords and vertical struts with steel rods forming diagonals within each panel.

The approach spans range from approximately 9.1m to 11m in length and are of timber beam construction, comprising five parallel timber logs spanning between timber and trestle piers. Each span has been

strengthened by the addition of four steel rolled steel joists (RSJs), one each located in between the timber logs. There is a footway on the southern side with a timber guardrail but the majority of the timber decking of the footway has been removed. The footway is absent on the lifting span and the footways have an entrance to the road deck on either side of the opening span (pedestrians are/were required to share the road deck with vehicles for the length of the opening span).

This site is part of the traditional land of the Yorta Yorta people.

HOW IS IT SIGNIFICANT?

The Old Cobram-Barooga Bridge is of historical and scientific significance to the State of Victoria. It satisfies the following criterion for inclusion in the Victorian Heritage Register:

Criterion A

Importance to the course, or pattern, of Victoria’s cultural history.

Criterion B

Possession of uncommon, rare or endangered aspects of Victoria’s cultural history.

Criterion F

Importance in demonstrating a high degree of creative or technical achievement at a particular period.

WHY IS IT SIGNIFICANT?

The Old Cobram-Barooga Bridge is historically significant as one of most important Murray River bridges constructed between New South Wales and Victoria. Built Federation era, the bridge was understood from its beginnings as an important physical symbol of the creation of a national Australian society out of disparate colonial social components. The bridge was an impressive capital works project which linked road, river and rail routes and facilitated economic and regional growth in both states. Although most of the bridge is in New South Wales it has a special significance in Victoria’s history because it was built entirely from Victorian funds and constructed by the Victorian bridge-building firm of JB and W Farquharson. [Criterion A]

The Old Cobram-Barooga Bridge is a rare de Burgh design timber truss bridge incorporating a metal Pratt lift-span. It features a steel lift-span on an iron and concrete substructure with two large de Burgh composite timber-steel truss spans one on each side of the steel lift-span. The de Burgh-Pratt composite timber-steel trusses were built only for a brief period between 1900 and 1904. This bridge is one of three surviving vertical lift-span bridges of this type in Australia and is one of two that retain all of their lift-span operating mechanisms intact. [Criterion B]

The Old Cobram-Barooga Bridge demonstrates a high degree of technical achievement because it represents the peak of lift-span technology in bridge engineering in Australia. The design was largely developed in New South Wales and the efficacy and durability of the design is evidenced by the survival of this bridge and many of its peers for over a century of use. It illustrates the historic need to embrace composite materials for bridges for practical and economic reasons and the ongoing adoption of innovations in bridge construction by Ernest de Burgh Australia's foremost engineers of the late colonial and post-Federation era whose work was influential in this field nationally and internationally. [Criterion F]

The Old Cobram-Barooga Bridge is also significant for the following reasons, but not at the State level:

The bridge is of significance to the people of northern Victoria and the Riverina region of New South Wales as it improved road, rail and river links between the states which encouraged the agricultural and economic development of these regions.

RECOMMENDATION REASONS

REASONS FOR RECOMMENDING INCLUSION IN THE VICTORIAN HERITAGE REGISTER [s.34A(2)]

Following is the Executive Director's assessment of the place against the tests set out in The Victorian Heritage Register Criteria and Thresholds Guidelines (2014).

CRITERION A

Importance to the course, or pattern, of Victoria’s cultural history.

STEP 1: A BASIC TEST FOR SATISFYING CRITERION A

The place/object has a CLEAR ASSOCIATION with an event, phase, period, process, function, movement, custom or way of life in Victoria’s cultural history.

PlusThe association of the place/object to the event, phase, etc IS EVIDENT in the physical fabric of the

place/object and/or in documentary resources or oral history.Plus

The EVENT, PHASE, etc is of HISTORICAL IMPORTANCE, having made a strong or influential contribution to Victoria.

Executive Director’s Response

The Old Cobram-Barooga Bridge is historically significant as one of most important Murray River bridges constructed between New South Wales and Victoria. It was an important post-Federation era infrastructure project and facilitated regional and population growth in both states. The opening up of northern Victoria and growth of agriculture made a strong and influential contribution to the Victorian economy.

Criterion A is likely to be satisfied.

STEP 2: A BASIC TEST FOR DETERMINING STATE LEVEL SIGNIFICANCE FOR CRITERION A

The place/object allows the clear association with the event, phase etc. of historical importance to be UNDERSTOOD BETTER THAN MOST OTHER PLACES OR OBJECTS IN VICTORIA WITH SUBSTANTIALLY THE

SAME ASSOCIATION.


The Old Cobram-Barooga Bridge facilitated the agricultural and economic development of northern Victoria in the post-Federation era as a result of improved road and river links between New South Wales and Victoria. It allows this to be understood better than most other places or objects in Victoria with substantially the same association.

Criterion A is likely to be satisfied at the State level.

CRITERION B

Possession of uncommon, rare or endangered aspects of Victoria’s cultural history.

STEP 1: A BASIC TEST FOR SATISFYING CRITERION B

The place/object has a clear ASSOCIATION with an event, phase, period, process, function, movement, custom or way of life of importance in Victoria’s cultural history.

PlusThe association of the place/object to the event, phase, etc IS EVIDENT in the physical fabric of the

place/object and/or in documentary resources or oral history.Plus

The place/object is RARE OR UNCOMMON, being one of a small number of places/objects remaining that demonstrates the important event, phase etc.

ORThe place/object is RARE OR UNCOMMON, containing unusual features of note that were not widely

replicatedOR

The existence of the class of place/object that demonstrates the important event, phase etc is ENDANGERED to the point of rarity due to threats and pressures on such places/objects.


The Old Cobram-Barooga Bridge is a rare de Burgh timber truss bridge with a metal Pratt lift-span. It features a steel lift-span on an iron and concrete substructure with two large de Burgh composite timber-steel truss spans (modelled on the American Pratt pattern) one on each side of the steel lift-span. The de Burgh/Pratt composite timber-steel trusses were built only for a brief period between 1900 and 1904.

Criterion B is likely to be satisfied

STEP 2: A BASIC TEST FOR DETERMINING STATE LEVEL SIGNIFICANCE FOR CRITERION B

The place/object is RARE, UNCOMMON OR ENDANGERED within Victoria.


The Old Cobram-Barooga Bridge is one of three surviving vertical lift-span bridges of this type in Australia and is one of two (including the Barham-Koondrook Bridge H0795) that retain all of their lift-span operating mechanisms intact.

Criterion B is likely to be satisfied at the State level.

CRITERION F

Importance in demonstrating a high degree of creative or technical achievement at a particular period.

STEP 1: A BASIC TEST FOR SATISFYING CRITERION F

The place/object contains PHYSICAL EVIDENCE that clearly demonstrates creative or technical ACHIEVEMENT for the time in which it was created.

PlusThe physical evidence demonstrates a HIGH DEGREE OF INTEGRITY.


The Old Cobram-Barooga Bridge is of technical significance because it represents the evolutionary peak of lift-span technology in bridge engineering in Australia. The design was largely developed in New South Wales and the efficacy and durability of the design is evidenced by the survival of this bridge and many of its peers for over a century of use.

Criterion F is likely to be satisfied.

STEP 2: A BASIC TEST FOR DETERMINING STATE LEVEL SIGNIFICANCE FOR CRITERION F

The nature &/or scale of the achievement is OF A HIGH DEGREE or ‘beyond the ordinary’ for the period in which it was undertaken as evidenced by:

critical acclaim of the place/object within the relevant creative or technological discipline as an outstanding example in Victoria; or

wide acknowledgement of exceptional merit in Victoria in medium such as publications and print media; or

recognition of the place/object as a breakthrough in terms of design, fabrication or construction techniques; or

recognition of the place/object as a successful solution to a technical problem that extended the limits of existing technology; or

recognition of the place/object as an outstanding example of the creative adaptation of available materials and technology of the period.


The Old Cobram-Barooga Bridge illustrates the ongoing adoption of innovations in bridge construction made by Ernest de Burgh, one of Australia's foremost engineers, of the late colonial and post-Federation era. De Burgh’s work was influential nationally and internationally.

Criterion F is likely to be satisfied at the State level.

PROPOSED PERMIT POLICYPreamble

The purpose of the Permit Policy is to assist when considering or making decisions regarding works to a registered place. It is recommended that any proposed works be discussed with an officer of Heritage Victoria prior to making a permit application. Discussing proposed works will assist in answering questions the owner may have and aid any decisions regarding works to the place.

The extent of registration of The Old Cobram-Barooga Bridge in the Victorian Heritage Register affects the whole place shown on Diagram 2352 including the land, all buildings, roads, trees, landscape elements and other features. Under the Heritage Act 1995 a person must not remove or demolish, damage or despoil, develop or alter or excavate, relocate or disturb the position of any part of a registered place or object without approval. It is acknowledged, however, that alterations and other works may be required to keep places and objects in good repair and adapt them for use into the future.

If a person wishes to undertake works or activities in relation to a registered place or registered object, they must apply to the Executive Director, Heritage Victoria for a permit. The purpose of a permit is to enable appropriate change to a place and to effectively manage adverse impacts on the cultural heritage significance of a place as a consequence of change. If an owner is uncertain whether a heritage permit is required, it is recommended that Heritage Victoria be contacted.

Permits are required for anything which alters the place or object, unless a permit exemption is granted. Permit exemptions usually cover routine maintenance and upkeep issues faced by owners as well as minor works or works to the elements of the place or object that are not significant. They may include appropriate works that are specified in a conservation management plan. Permit exemptions can be granted at the time of registration (under s.42 of the Heritage Act) or after registration (under s.66 of the Heritage Act).

It should be noted that the addition of new buildings to the registered place, as well as alterations to the interior and exterior of existing buildings requires a permit, unless a specific permit exemption is granted.

Conservation management plans

It is recommended that a Conservation Management Plan is developed to manage the place in a manner which respects its cultural heritage significance.

Cultural heritage significance

Overview of significance

The cultural heritage significance of the Old Cobram-Barooga Bridge lies in its historical significance as one of most important Murray River bridges constructed between New South Wales and Victoria. Built in the Federation era, it was an impressive capital works project which formed part of a broader network of road, river and rail routes and facilitated economic and regional growth in both states. The Old Cobram-Barooga Bridge is a rare de Burgh timber truss bridge with a metal Pratt lift-span. It is one of three surviving vertical lift-span bridges of this type and is one of two that retain all of their lift-span operating mechanisms intact. The Bridge is of technical significance because it represents the peak in the evolution of lift-span technology in bridge engineering in Australia.

Archaeological: Ground disturbance may affect the archaeological significance of the place and, subject to the exemptions stated in this document, requires a permit.

PROPOSED PERMIT EXEMPTIONS (UNDER SECTION 42 OF THE HERITAGE ACT)It should be noted that Permit Exemptions can be granted at the time of registration (under s.42(4) of the Heritage Act). Permit Exemptions can also be applied for and granted after registration (under s.66 of the Heritage Act)

General Condition 1

All exempted alterations are to be planned and carried out in a manner which prevents damage to the fabric of the registered place or object.

General Condition 2

Should it become apparent during further inspection or the carrying out of works that original or previously hidden or inaccessible details of the place or object are revealed which relate to the significance of the place or object, then the exemption covering such works shall cease and Heritage Victoria shall be notified as soon as possible.

General Condition 3

All works should be informed by Conservation Management Plans prepared for the place. The Executive Director is not bound by any Conservation Management Plan, and permits still must be obtained for works suggested in any Conservation Management Plan.

General Condition 4

Nothing in this determination prevents the Heritage Council from amending or rescinding all or any of the permit exemptions.

General Condition 5

Nothing in this determination exempts owners or their agents from the responsibility to seek relevant planning or building permits from the relevant responsible authority, where applicable.

Specific Permit ExemptionsPermit exemptions as outlined in Standard Exemptions for Works Requiring Heritage Council Approval, Heritage Branch, New South Wales Department of Planning as approved the New South Wales Minister of Planning, 25 March 2009.

RELEVANT INFORMATIONLOCAL GOVERNMENT AUTHORITY Berrigan Shire Council, New South Wales

Shire of Moira, Victoria

HERITAGE LISTING INFORMATION

Heritage Overlay: No

Heritage Overlay Controls: NA

Other listing: National Trust Listed (State Level)

HISTORY

The Old Cobram-Barooga BridgeSince the beginnings of European settlement the waters of the Murray River have been a key factor in the commercial agricultural development of what has been some of the most productive land in modern Australia. From the 1830s onwards crossing the river became a necessity and this involved the construction of infrastructure such as wharves, weirs, locks, bridges, including pontoon and truss bridges. By the mid-nineteenth century toll-ferries and row boats had a monopoly on transporting people and goods across the river. In 1879 two bridges opened - the Murray Bridge and the Echuca-Moama Bridge. From 1889 a punt operated between Cobram in (Victoria) and Barooga (New South Wales) and was the only means of crossing the river at this point.

By the 1890s the limited capacity of ferries became a hindrance to the steadily increasing road traffic. In response the Colonial Governments of New South Wales and Victoria began a joint program of building bridges for land-based transport and that would accommodate paddle steamers. High-level bridges were the ideal, but the combination of expensive river spans and long approach viaducts graded to suit horse and bullock drays made this option too costly. The affordable alternative was low-level bridges with moveable spans. This solution had already been anticipated when in 1858 Henry Hopwood established a pontoon bridge at Echuca. During the 1880s and 90s the Colonial Governments of New South Wales and Victoria began a joint program of building bridges with opening spans which could accommodate paddle steamers, trains and road traffic.

The bridge building program coincided with discussions about the use of Murray River water for agricultural irrigation between the colonies. During the 1870s closer settlement programs highlighted the need for a regular water supply and in 1887 George Chaffey commenced designing a massive irrigation scheme at Mildura. In 1893, representatives of the three states met in Melbourne and considered the installation of locks on the Murray River to preserve supplies for irrigation and facilitate river transport. Economic conflicts of interests between the colonies stymied coordinated action. Federation in 1901 meant that the three states in which the Murray flowed were no longer in competition. In 1902 a Royal Commission recommended joint control of the Murray River by the three states and a joint funding arrangement for water conservation infrastructure, such as dams and weirs. As irrigation systems grew there continued to be a need for bridges over the Murray River between Victoria and New South Wales.

The prospect of a bridge in the Cobram-Barooga district had been discussed regularly at public meetings since 1884. By November 1899, Government Ministers in both states reported that decisions had been taken to proceed with the bridge and that specifications were being prepared. After Federation was given royal

assent on 9 July 1900 the declaration of tenders for the Bridge were awarded in November 1900. It was decided that the bridge would be financed and built by the Victorian government. The bridge was constructed by the prolific Victorian bridge-building firm of JB and W Farquharson of Melbourne. The Bridge opened officially on 3 December 1902, two months after being open to traffic. It provided access for heavy goods vehicles and the central lift-span allowed paddle steamers to pass underneath. The improved capacity to transport agricultural goods, particularly wool and wheat, to Melbourne, Sydney and larger regional towns consolidated the importance of north-eastern Victoria and the Riverina District of New South Wales.

The Cobram Bridge is the only bridge on the Murray River whose construction was completely funded by the Victorian government. It appears that the Victorian Country Roads Board was also responsible for its maintenance after opening. The construction of the bridge is evidence of the value of the wool industry in the vicinity and of the economic flows of goods between NSW and Victoria. In 2002 a high level concrete bridge was built to the south of the original 1902 bridge, which remains open for pedestrian traffic.

The development of bridge technology

In Australia, stone (and brick) arch bridges provided the major form of bridge until the middle of the nineteenth century, after which, local engineers turned to timber truss bridges to provide the majority of river crossings, with the (expensive) imported wrought iron bridges reserved for railways and the larger and more heavily trafficked roads. Although timber beam bridges are limited by the dimensions of available materials, timber offered the cheapest and quickest bridge solution. In NSW, the availability of excellent hardwoods provided Public Works engineers McDonald, Allan, Dare and de Burgh with a uniquely strong and durable material for timber truss bridges. Timber beam bridges served well for 150 years as relatively inexpensive structures to aid the movement of goods and people.

In the latter half of the nineteenth century the emergence of steel provided a cheaper, stronger and more adaptable material for bridges than cast or wrought iron. It was rapidly adopted world-wide, its application limited only by its relative cost. In Australia, this meant that its use continued to be constrained until after local manufacture commenced in 1915. In response, the timber truss bridge designs in NSW evolved after 1899 to include steel members in critical locations such as bottom chords, whilst continuing to utilise timber for the majority of the bridge structure. There were five main types of timber truss bridges erected in NSW, distinguished by the evolving arrangement of the primary truss members. The five types are:

1860-1886 Public Works Department Truss (PWD)

A basic truss bridge, based upon English models, in use from 1860 to 1886. It took advantage of the local hardwoods for its main members and was a solid and durable design.

1886 to 1893 McDonald Truss Built from 1886 to 1893, the McDonald truss improved upon the Old PWD type by addressing several of its particular shortcomings. These included the placement of cast-iron shoes at the junctions between timber beams, the end members were doubled and splayed for better lateral stability and wrought-iron rods were utilised for vertical tension members.

1893 to 1929 Allan Truss Built from 1893 to 1929, the Allan type also used cast iron connection pieces and vertical iron rods but was a significant improvement on the McDonald type, with most main members doubled and spaced, a simplified tensioning system and using smaller individual pieces of timber.

1899 to 1905 de Burgh Truss The de Burgh Truss was built from 1899 to 1905. This truss was a composite truss, utilising timber and steel in combination. It was distinguished by the use of pin-joints in the connections between

the steel bottom chords and the steel diagonal rods. The de Burgh Truss was an adaptation of the American Pratt Truss design developed by Americans Thomas and Caleb Pratt in 1844. Prevalent from the 1840s through the early twentieth century, the Pratt truss inspired a large number of variations and modified subtypes during the nineteenth and early twentieth centuries.

Schematic design of a de Burgh TrussSource: RTA NSW Timber Truss Bridge Strategy – de Burgh truss Bridge Profiles

1905 to 1936 Dare Truss The Dare Truss is very similar to an Allan truss but used steel bottom chords. Designed by Harvey Dare and built from 1905 to 1936, the Dare Truss incorporates the best features of both the Allan Truss and the de Burgh Truss, whilst eliminating the pin-joints of the latter that proved problematic in maintenance. The Dare Truss was the most successful of the timber/steel composite trusses.

The Old Cobram-Barooga Bridge was designed by Ernest de Burgh and uses de Burgh Trusses. The de Burgh Truss is unique amongst the five timber truss types, as it was the first to depart from the previous standard type. A defining feature of the Old Cobram-Baroonga Bridge its arrangement, with timber vertical posts, timber top-chords and steel rods as inclined tension members, bottom chords formed by continuous parallel steel plates, steel plates and diagonal rods connected to the bottom chords by turned pins. The Cobram-Barooga Bridge also has a movable lift-span bridge whereby a horizontal span, counterweighted between two towers, could be raised vertically to provide a passageway for the steamers and their towed barges. Opening-span bridges were built from 1890 until 1941, after which no new opening bridges were erected on the Murray River.

Ernest de Burgh

Ernest Macartney de Burgh (1863-1929) was one of Australia's foremost engineers of the late colonial period and the early 20th century. He was born in Dublin, Ireland and received his engineering education at the Royal College of Science. At age 22 he arrived in Melbourne then onto Sydney where he joined the New South Wales Department of Public Works on 30 April 1885. He was to specialise in the design and construction of bridges, water supply schemes and dams. In 1901 de Burgh was appointed Engineer for Bridges in NSW and by that time had been associated with many major bridges. This included the 50 metre single truss bridge over the Lane Cove River which was at the time the longest timber truss span ever built in Australia. He also developed the composite timber and steel truss that now bears his name, and was a member of the Sydney Harbour Bridge Advisory Board. Ernest Macartney de Burgh was regarded as one of the ablest civil engineers in Australia whose achievements had been recognised internationally.

DESCRIPTION

The Old Cobram-Barooga Bridge is a timber truss, lift-span bridge carrying two traffic lanes across the Murray River between Cobram and Barooga. The primary axis of the bridge is east-west. The bridge has a clearance over normal water level of 7.9m with the lift-span closed and 14.3m with the lift-span open. The bridge has been superseded by a parallel bridge and no longer carries vehicular traffic. The three main spans include a single, vertical-lift opening span supported on cast iron piers in the centre of the bridge, flanked by a single de Burgh Truss span on each side. The eastern (NSW) side has been truncated and retains only one timber beam approach span, which terminates in a steel fence and stair to ground level. All three timber beam approach spans survive on the western (Victorian) side. The outer ends of the truss spans and the approach spans are carried on timber trestles on timber piles. The outer ends of the lift-span are carried on twin cylindrical cast iron piers with intermediate perforated steel plate braces.

The lift-span is formed by a roadway between riveted Pratt-Truss box-girders with a span of 18m. The road deck on the lift-span is narrower than the approaches and reduces to one traffic lane. The lifting superstructure comprises four steel lattice towers, connected at their upper level by steel lattice girders. The two de Burgh truss spans, each 31.7m, are of composite timber and steel construction, with paired timber top chords and vertical struts with steel rods forming diagonals within each panel.

The approach spans range from approximately 9.1m to 11m in length and are of timber beam construction, comprising five parallel timber logs spanning between timber and trestle piers. Each span has been strengthened by the addition of four steel RSJs, one each located in between the timber logs. There is a footway on the southern side with a timber guardrail but the majority of the timber decking of the footway has been removed. The footway is absent on the lifting span and the footways have an entrance to the road deck on either side of the opening span (pedestrians are/were required to share the road deck with vehicles for the length of the opening span).

The bridge links Cobram and Barooga, but is situated on a broad stretch of Murray River floodplain, within a picturesque rural context of spreading red-gum trees belonging to the Barooga State Forest.

CONSTRUCTION DETAILS

Bridge engineer: Ernest Macartney de Burgh

Builder name: JB and W Farquharson

Construction end date: 1904

VICTORIAN HISTORICAL THEMES

03 Connecting Victorians by transport and communications3.2 Travelling by water3.4 Linking Victorians by road in the 20th century

04 Transforming and managing land and natural resources4.7 Transforming the land and waterways

INTEGRITY/INTACTNESS

Intactness – The remaining components are largely intact. (March 2014)

Integrity – Integrity spoilt by removal of northern approach spans. The eastern (NSW) side has been truncated and retains only one timber beam approach span, which terminates in a steel fence and stair to ground level. All three timber beam approach spans survive on the western (Victorian) side. (March 2014)

CONDITION

Bridge fabric condition generally good . (March 2014)

COMPARISONS

There are four bridges over the Murray River currently included in the VHR as joint registrations with the State Heritage Register (SHR) of New South Wales, and which have similar cultural heritage values to the Old Cobram-Barooga Bridge:

1. Swan Hill Bridge (1896)2. Barham-Koondrook Bridge (1904)3. Tooleybuc Bridge (1925)4. Bethanga Bridge (1930)

Swan Hill Bridge (1896) H0794

INCLUDEPICTURE "http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0794/Swan Hill Bridge_Swan Hill_Feb

2008_mz_080.jpg/medium.jpg&context=ImageFactory.Hermes&delete=no&version=" \* MERGEFORMATINET INCLUDEPICTURE

"http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0794/Swan Hill Bridge_Swan Hill_Feb



















2008_mz_080.jpg/medium.jpg&context=ImageFactory.Hermes&delete=no&version=" \*

MERGEFORMATINET

Built in 1896 by the Victorian bridge builders, Farquharson Brothers, to a design by New South Wales Public Works Department Engineer, Percy Allan, the Swan Hill Bridge is a timber truss and steel centre lift-span bridge over the Murray River at Swan Hill. The Bridge is of technical (scientific) significance for the innovations used in its design and construction. At the time of construction, the Bridge represented some of the most sophisticated methods in Australian bridge construction. The Bridge is of historical significance for its role in facilitating inter-colonial trade between New South Wales and Victoria. The Bridge provided a vital

link between the pastoral runs in the New South Wales Riverina to the railways on the Victorian side of the Murray allowing easy transport of wool to the Victorian markets and ports. The link also benefited drovers overlanding livestock between Queensland and the Victorian markets. In time the bridge also provided an essential link between the Moulamein-Wakool irrigation areas and the Swan Hill rail head and Victorian markets and sea ports.

Barham-Koondrook Bridge (1904) H0795

INCLUDEPICTURE "http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0795/Koondrook-Barham Bridge_Koondrook_Feb


"http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0795/Koondrook-Barham Bridge_Koondrook_Feb




















MERGEFORMATINET

The Barham-Koondrook Bridge was built in 1904 by engineering firm Monash and Anderson. It was the twelfth bridge to cross the Murray River. The Barham-Koondrook Bridge is of technical (scientific) significance as it is a rare combination of the Percy Allan designed steel central lift-span with composite De Burg trusses. The only other Murray River bridge to have this configuration is The Old Cobram-Barooga Bridge. The Barham-Koondrook Bridge is of historical significance as it directly connected the pastoral and agricultural concerns in the Riverina with the Victorian railhead at Koondrook and has long been an important link in the north-south stock route connecting Victoria with the New South Wales and Queensland pastoral centres. The bridge also has associations with John Monash who was one of Australia's most important engineers, and one of the country's most famous soldiers.

Tooleybuc Bridge (1925) H0765

INCLUDEPICTURE "http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0765/Tooleybuc Bridge_Tooleybuc_Feb


"http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=PROV H0765/Tooleybuc Bridge_Tooleybuc_Feb




















MERGEFORMATINET

Built in 1925, the Tooleybuc Bridge is a timber truss and steel lift-span bridge over the Murray River at Tooleybuc in New South Wales, near Piangil in Victoria. There are only two surviving Murray River bridges with Allan truss spans – Swan Hill and Tooleybuc. Swan Hill Bridge was the first of its type to be constructed anywhere, and the Tooleybuc Bridge was the last. Both bridges were built with Allan trusses in conjunction with Percy Allan designed steel lift-spans. The Tooleybuc Bridge is of technical (scientific) significance for its sophisticated design and construction. The Tooleybuc Bridge was the last of a series of bridges over the Murray River that incorporated central lift-spans with innovative truss spans. The Tooleybuc Bridge is of historical significance for its role in facilitating interstate trade between New South Wales and Victoria.

INCLUDEPICTURE "http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=hvi2009/eastern_rural_compressed/h0989_dig0217.jpg/

medium.jpg&context=ImageFactory.Hermes&delete=no&version=" \* MERGEFORMATINET INCLUDEPICTURE "http://applications.doi.vic.gov.au/ImageFactoryWeb/getfile?path=hvi2009/

eastern_rural_compressed/h0989_dig0217.jpg/medium.jpg&context=ImageFactory.Hermes&delete=no&version=" \* MERGEFORMATINET









eastern_rural_compressed/h0989_dig0217.jpg/






Bethanga Bridge (1930) H0989

The Bethanga Bridge, was built between 1927 and 1930 as a joint venture between New South Wales and Victoria. The Bridge is a road bridge over a flooded section of a Murray River valley that now forms part of the Hume Dam. It consists of Pratt trusses built by Vickers Ruwolt in Melbourne. The Bridge is of historical significance for its associations with the construction of Hume Dam and the River Murray Waters Commission. It is of scientific (technical) significance to the State of Victoria for the rare use of Pratt trusses in Victoria. The use of this system symbolises the cooperation of New South Wales and Victoria in the development and ongoing use of major Murray River infrastructure.

The Old Cobram-Barooga Bridge (1904) shares similar values to the Murray River bridges listed above and demonstrates state level technical and historical significance. It and the Barham-Koondrook Bridge (1904) are rare as the only two surviving bridges consisting of a combination of the Percy Allan designed steel central lift-span with composite de Burgh trusses.

KEY REFERENCES USED TO PREPARE ASSESSMENT

NSW State Heritage Register Nomination Form, Department of Planning/Heritage Council, NSW, September 2015.Don Fraser, ‘Cobram-Barooga Bridge over the River Murray’, in Newsletter of Engineering Australia, no.15, August 2004.Berrigan Shire, Cobram-Barooga Bridge http://berriganshire.nsw.gov.au/QuickLinks/FlashbackFriday/tabid/263/articleType/ArticleView/articleId/2190/Cobram-Barooga-Bridge.aspx

PROPOSED TEXT FOR THE BLUE HERITAGE PLAQUE

This rare de Burgh truss bridge (1904) is one of most important bridges constructed between Victoria and New South Wales. It facilitated agricultural, population and economic growth and represents the apex of lift-span bridge engineering in Australia.

ADDITIONAL IMAGES / MAPS

Map image showing the New Barooga-Cobram Bridge running along Vermont Street, and the Old Barooga-Cobram Bridge to the north.

Aerial photo from Wikimapia.

INCLUDEPICTURE "http://www.travelnsw.com.au/images/barooga/photos/12.jpg" \* MERGEFORMATINET INCLUDEPICTURE

"http://www.travelnsw.com.au/images/barooga/photos/12.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.travelnsw.com.au/images/barooga/photos/12.jpg" \*

MERGEFORMATINET INCLUDEPICTURE "http://www.travelnsw.com.au/images/barooga/photos/12.jpg" \* MERGEFORMATINET





"http://www.travelnsw.com.au/images/barooga/photos/12.jpg" \* MERGEFORMATINET

Pre-2006View from West Bank of the Murray back into New South Wales across the Old Cobram-Barooga Bridge prior

to the building of the New Barooga-Cobram Bridge.Source: http://www.travelnsw.com.au/barooga/photos/

INCLUDEPICTURE "https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/

800px-CobramBaroogaBridgeOld.JPG" \* MERGEFORMATINET INCLUDEPICTURE "https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/



800px-CobramBaroogaBridgeOld.JPG" \* MERGEFORMATINET INCLUDEPICTURE



"https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/800px-CobramBaroogaBridgeOld.JPG" \* MERGEFORMATINET INCLUDEPICTURE





"https://upload.wikimedia.org/wikipedia/commons/thumb/4/47/CobramBaroogaBridgeOld.JPG/800px-CobramBaroogaBridgeOld.JPG" \* MERGEFORMATINET

Post-2006View from West Bank of the Murray back into New South Wales across the Old Cobram-Barooga Bridge after

the building of the New Barooga-Cobram Bridge (see concrete supports).Source: http://www.travelnsw.com.au/barooga/photos/

INCLUDEPICTURE "https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \*

MERGEFORMATINET INCLUDEPICTURE "https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-side-cobram-barooga-

bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET INCLUDEPICTURE "https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-

side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET INCLUDEPICTURE

"https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET



bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET

https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg






bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET INCLUDEPICTURE "https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-

side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET INCLUDEPICTURE

"https://communityhistoryoz.files.wordpress.com/2012/10/bridges-side-by-side-cobram-barooga-bridge-24-09-12-shannonkneebone.jpg?w=450&h=302" \* MERGEFORMATINET

View from New South Wales in to Victoria. The old and new Cobram-Barooga Bridges (2012)

Source: https://communityhistoryoz.wordpress.com/cobram-barooga-bridge/present-day-debates-to-destroy-or-conserve/©ShannonKneebone



View from Victoria into New South Wales along the Old Cobram-Barooga Bridge in the 1990s.

Source: http://www.travelnsw.com.au/barooga/photos/











"http://www.travelnsw.com.au/images/barooga/photos/13.jpg" \* MERGEFORMATINET

View east from Victoria along the Old Cobram-Barooga Bridge into New South Walesprior to the building of the New Barooga-Cobram Bridge. Source: http://www.travelnsw.com.au/barooga/photos/

Postcard image of the Cobram Bridge, undated (High Country Library Corporation).

HERITAGE COUNCILheritagecouncil.vic.gov.au/.../Old-Cobram-Barooga-Bridge.doc · Web viewSchematic...

Documents

Transcript of HERITAGE COUNCILheritagecouncil.vic.gov.au/.../Old-Cobram-Barooga-Bridge.doc · Web viewSchematic...