HDB SOR - Jul 2013

STANDARD SCHEDULE OF RATES FOR:

BUILDING WORKS,

CIVIL ENGINEERING WORKS AND

ELECTRICAL WORKS

(JUL 2013 EDITION)

STANDARD SCHEDULE OF RATES FOR BUILDING WORKS (JUL 2013)

HOUSING AND DEVELOPMENT BOARD

STANDARD SCHEDULE OF RATES

FOR

BUILDING WORKS (JUL 2013)

CONTENTS

S/N DESCRIPTION PAGE

GENERAL PREAMBLES 1 - 3

PARTICULAR PREAMBLES TO VARIOUS TRADES 4 - 18

1 EXCAVATION 19 - 21

2 CONCRETE WORK 22 - 31

3 BRICKWORK AND BLOCKWORK 32 - 33

4 FLOOR FINISHES 34 - 39

5 ROOFING 40 - 41

6 CARPENTRY AND JOINERY 42 - 47

7 IRONMONGERY 48 - 50

8 STRUCTURAL STEELWORK & METALWORK 51 - 66

9 WALL AND CEILING FINISHES 67 - 68

10 SANITARY, WATER AND GAS INSTALLATION 69 - 86

11 GLAZING 87 - 88

12 PAINTING AND DECORATING 89 - 91

13 TURFING, TREE PLANTING & LANDSCAPING WORKS 92 - 94

14 MISCELLANEOUS 95 - 97

15 DAYWORK 98 - 100

Published by Housing and Development Board, Republic of Singapore.

No part of this document may be reproduced or copied in any form or

by any means without the prior written permission of the publisher.

of 100

GENERAL PREAMBLES Introduction

1.1 The clauses in the General Preambles shall apply to all work items

contained in the Standard Schedule of Rates. 1.2 The Particular Preambles to each Trade shall be read in conjunction with

the respective Trade in the Standard Schedule of Rates. 1.3 All rates include the allowances for complying with the General and

Particular Preambles. 2 All rates contained in the Standard Schedule of Rates are fixed basic

rates (in Singapore Currency) and no amendment whatsoever shall be made to such rates. The tenderers shall be deemed to have closely studied all rates contained herein and duly noted their implications.

3 All rates contained in this Standard Schedule of Rates are exclusive of

any Goods and Services Tax. Any such Goods and Services Tax shall be borne by the HDB as and when the same becomes due and payable.

4 All work, materials and goods described in this Standard Schedule of

Rates shall be of the respective kinds described in the Contract and in accordance with the instructions of the Superintending Officer or the Superintending Officer's Representative.

5 Headings to groups of items shall be read as part of the descriptions of

the items to which the headings apply. 6 Where brand/trade names are given in the descriptions, they are solely

intended for fixing the rates of the items. The products and materials to be used in the contract shall be governed by the specifications, Drawings and other documents forming the contract (and not this Schedule of Rates).

Description of Works and Inclusions

7 Unless specifically stated otherwise, the following shall be deemed to be included in the description of the item of work:-

a) Labour and all costs in connection therewith including the labour in

fabricating, assembling, setting, fitting and fixing of materials and goods in position.

of 100

GENERAL PREAMBLES

Description of Works and Inclusions (Cont’d)

b) Materials and goods including materials required for lapping, jointing and the like and all costs in connection therewith such as delivery, unloading, storing, returning of packings, handling, hoisting and lowering.

c) Preparing surfaces to receive work.

d) Protecting materials and work. e) Waste of materials.

f) All cutting and waste.

g) Use of construction equipment, tools, vehicles and all costs in

connection therewith.

h) Cleaning up on completion and making good all work disturbed.

i) General requirements set out in the Specifications, Drawings and other documents forming the Contract.

j) Establishment charges, overhead and profit.

8 Unless otherwise stated, all work shall be measured net as fixed in its place.

9 Where minimum deductions of voids are dealt with in this document they

shall refer only to openings or voids which are within the boundaries of measured area. Openings or voids which are at the boundaries of measured area shall always be the subject of deductions irrespective of size.

Billing of Quantities

10.1 Where the unit of measurement is the linear metre, square metre and cubic metre, quantities shall be billed to the nearest whole unit. Fractions of the unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit.

of 100

GENERAL PREAMBLES

Billing of Quantities (Cont'd) 10.2 Where the unit of measurement is the kilogramme, quantities shall be

billed to the nearest whole unit. Fractions of a unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit. Where the unit of billing is the tonne or litre, quantities shall be billed to the nearest two places of decimals.

10.3 Where the unit of measurement is the hour, fractions of the unit shall be billed to the nearest next half hour. 10.4 Where the application of clauses 11.1 and 11.2 would cause an entire

item to be eliminated, such item shall be billed to the nearest two places of decimals.

11 Where rates with descriptions pertain to the same purpose are listed in

more than one Standard Schedule of Rates incorporated in the Contract; the rate as listed in the following schedules (in the stated order of precedence) shall prevail:-

1st Precedence - Standard Schedule of Rates for

Building Works

2nd Precedence - Standard Schedule of Rates for Civil Engineering Works

3rd Precedence - Standard Schedule of Rates for

Electrical Works 12 Unless otherwise stated, the term "as specified" means as specified in

any of the documents forming part of the Contract. 13 The following abbreviations are used for the units:-

m - Linear metre m2 - Square metre m3 - Cubic metre no - Number kg - Kilogram ton - Tonne pr - Pair sht - Sheet ltr - Litre hr - Hour

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES

1.0 EXCAVATION

Definition of Ground 1.1 Ordinary ground:- includes spoil or rubbish of every description, rubbish

tip material etc, sand gravel, decomposed granite, red or white earth, loamy or gravelly clay, gravelly laterite, mud, bog or any other formation of pick and shovel and at any depth.

Description

1.2 The description of each item of excavation shall be deemed to include excavating around foundation, piles and confined areas, getting out, removing of bakau piles, trimming, levelling and compacting bottoms of excavations, keeping sides plumb and planking and strutting.

Measurement

1.3.1 The measurement of all excavations and subsequent disposal shall be those before excavating. The increases in bulk and any extra excavation required for earthwork support, planking and strutting and formwork for concrete shall be deemed to be included in the rates.

1.3.2 No allowance for working space shall be made in the measurement of all

excavation unless the method of construction requires workmen to operate from the outside of the structure. In such cases, a working space of 600mm shall be measured from the external face of the structure.

1.3.3 Filling shall be measured as equal to the void to be filled. Any thickness

stated shall be deemed to be after compacting.

Rate 1.3.4 Rates for each item shall be held to include for keeping all excavation free

from water and site dry, pumping or bailing if required and providing any temporary drains required.

1.4 Pre-Treatment of Soil against Subterranean Termites

Measurement 1.4.1 Soil treatment shall be measured flat on plan and the method of

measurement shall be up to the perimeter of the building line (excluding the apron areas). Link buildings, linkways and other structures shall also be similarly measured.

1.4.2 No deduction shall be made in the measurement for plan areas occupied

by the column stumps.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 1.0 EXCAVATION (CONT’D) 1.4.3 The rates indicated shall be inclusive of the provision of warranty and

shall not in any way affect the provisions of Building Specifications on Pre-Treatment of Soil for Protection of Buildings Against Subterranean Termites which provisions remain applicable in every respect in relation to all situations where these rates are applied.

2.0 CONCRETE WORK

Rate 2.1 Rates for each item of concrete shall be held to include the following:-

a) Forming, cutting grooves, chases, mortices, holes and making good any other sundry items of a like nature.

b) Extra labour for laying to falls, or cambers and preparing surfaces

to receive screeds or pavings also to be included.

c) All tests on concrete, cement and aggregate etc, as required and compliance with the strengths as specified.

d) Tamping and/or vibrating to give thorough compaction; working

between and around reinforcements.

e) Laying on any type of sub-base; preparing and leaving surfaces to receive screeds or paving.

Deduction

2.2 No deduction shall be made in the measurement of concrete work for:- a) Voids of 0.05 cubic metre or less.

b) Volume of the reinforcement and steelwork.

c) Openings in walls, floor, roof slabs and the like of 0.10 square

metre or less. Measurement 2.2.1 In the measurement of concrete for pile caps, the overall dimensions of

the pile caps shall be taken. No deduction shall be made for the precast formwork panels.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 2.0 CONCRETE WORK (CONT'D) 2.3 Reinforcement

Description 2.3.1 The description of each item of reinforcement shall be deemed to

include:- a) Allowances in the weight of reinforcement for rolling margins.

b) All cleaning, cutting, bending, fabricating, placing, tying and the

provision of all necessary distance blocks, tying wires, spacers or chairs, temporary fixings and supports.

Measurement 2.3.2 The conversion factor for the various steel reinforcement bars shall be as

follows:

6mm diameter - 0.222 kg/m 7mm diameter - 0.302 kg/m 8mm diameter - 0.394 kg/m 9mm diameter - 0.499 kg/m 10mm diameter - 0.616 kg/m 13mm diameter - 1.042 kg/m 16mm diameter - 1.579 kg/m 20mm diameter - 2.466 kg/m 22mm diameter - 2.984 kg/m 25mm diameter - 3.854 kg/m 28mm diameter - 4.834 kg/m 32mm diameter - 6.313 kg/m

2.4 Fabric Reinforcement

Rate 2.4.1 Rates for each item of fabric reinforcement shall be held to include for

extra material at laps, tying wires and all bending, cutting and notching around obstruction. Only the net area covered shall be measured and no deduction shall be made for opening less than 1.00 square metre.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 2.0 CONCRETE WORK (CONT'D) 2.5 Cage Reinforcement

Rate 2.5.1 Rates for each item of cage reinforcement shall be held to include for

extra material at laps.

Measurement 2.5.2 The area of Beam Stirrup Cage Reinforcement shall be the product of the

perimeter of stirrup multiplied by the length of the Cage. 2.5.3 The area of the Capping Link shall be the product of the perimeter of the

Link multiplied by the length of the Cage. 2.5.4 The area for prefabricated pilecap mesh reinforcement shall be based on

the bottom flat area of the mesh reinforcement without considering the upward projecting bars.

2.5.5 The area for dowel mesh reinforcement shall be the product of the length

and breadth which includes the depth of the bend. 2.6 Formwork

Description 2.6.1 The description of each item of formwork shall be deemed to include:-

a) All necessary boardings, supports, erecting, framing, cutting, perforations for pipes, angles, cleaning, wetting and treatment with mould oil, mould liquid or limewhite and the like.

b) All splayed edges, notchings, allowance for overlaps and passings

at angles, battens, strutting, bolting, wedging, easing, striking and removal.

Measurement

2.6.2 Formwork shall be measured to the surface of work sloping more than 15 degree from the horizontal.

Deduction

2.6.3 No deduction shall be made in measurement of formwork for:-

a) Openings less than 1 square metre.

b) Intersection of main and secondary beams.

c) Intersection of beams and stanchion casing or columns.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 2.0 CONCRETE WORK (CONT'D) 2.7 Unless otherwise stated, rates for concrete, reinforcement and formwork

shall be applicable to all work irrespective of locality, positions, shapes and height.

2.8 Precast Work

Description 2.8.1 a) All precast concrete components shall be grade 40 concrete as

specified unless otherwise indicated. b) The description of each item of precast work shall be deemed to

include concrete, reinforcement, formwork including the formation and filling of pockets, holes, chases and recesses for anchors, bolts and the like, grouting, pointing of joints, surface finishes, delivery, unloading, hoisting, erecting, fixing including all necessary temporary erection gear, bracing and working platforms.

2.9 Precast Concrete Vent

Measurement 2.9.1 The measurement of precast concrete vents shall be taken by volumes

without deduction of voids. 2.10 Piling Work 2.10.1 Piling work shall be executed in accordance with the relevant

Specifications and the instructions of Superintending Officer's Representative.

Description

2.10.2 The description of each type of piling work shall be deemed to include removal of underground obstructions together with all work in connection therewith unless specifically otherwise provided.

2.10.3 The description of each type of piling work shall be deemed to include

extending piles, dollying and connections unless specifically otherwise provided.

2.10.4 Redriving or intermittent driving necessitated by lengthening or upheaving

of piles or by the removal of obstructions under piles or other causes including moving and repositioning the piling frame shall be deemed to be included with the items of piling.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 2.0 CONCRETE WORK (CONT'D) 2.10 Piling Work (Cont'd) Rate 2.10.5 The rate of each item of piling shall be deemed to include:-

a) Handling, pitching, heading, pointing and bracing and providing protective wrought iron ring or helmet to pile.

b) Cutting off surplus and heads of piles, preparing and integrating

reinforcement into pile caps where applicable, extra excavation, backfilling and disposal of debris.

c) Disposing of materials displaced arising out of driving the piles.

2.10.6 The rate of each item of treated timber piles includes the application of

wood preservative to cut off surfaces of piles. 2.10.7 The rate of each item of reinforced concrete piles includes moulds,

reinforcement, preparing heads and extra labour and materials to receive pile extensions.

2.10.8 The rate of each item of pile tests includes provision of all anchors,

platforms, loading and unloading of materials, instruments and monitoring of the tests.

2.10.9 Movement of piling frames into position and about the site, any necessary

excavation or filling required to place the frames, raising or lowering the frames and any staging, barges or the like required to support the frames, shall be deemed to be included with the item of piling. Measurement

2.10.10 Payment for treated timber piles driven shall be the product of the relevant rate per metre run and the penetration depth (measured from tip to cut-off level).

2.10.11 The pay length of each reinforced concrete pile after it is driven into the

ground is measured from the cut-off level of the pile to the end of pile shoe. Notwithstanding the provisions of Billing of Quantities contained in the General Preambles, the pay length of reinforced concrete piles shall be billed to the accuracy of nearest of 10mm.

of 100


2.0 CONCRETE WORK (CONT'D) 2.11 Surface Water Channels

Rate 2.11.1 Rates for each item of surface water channels shall be held to include for

all angles, intersections, ends, outlets and extra labour and material for forming grooves or rebates to sides.

Measurement 2.11.2 Where an item is described as “Add to last item for the increase in stages

of 150mm deep”, the difference of any depth less than 150mm shall be paid based on 150mm depth.

3.0 BRICKWORK AND BLOCKWORK

Rate 3.1 The rates for each item of block, brickwork shall be held to include for all

special made blocks, bricks and in-situ concrete in lieu, all rough and fair cuttings, oversailing and receding courses, rough relieving and discharging arches, wedging and pining, raking out joints for and pointing flashings, bedding plates, bedding and pointing of frames, parging and coring flues, labour eaves filling, plumbing angles, forming square and rebated reveals, cut squints or birdsmouths, notches, forming, leaving or cutting chases, holes and mortices, cutting and pining and making good and any other sundry items of a like nature.

3.2 Rates for blockwork and brickwork shall be applicable to all work

irrespective of positions, patterns, shapes and height.

Deduction 3.3 Deductions shall be measured the net sizes of the openings and

recesses, including the extra width or rebated reveals. No deductions shall be made for openings of 0.50 square metre or less.

3.4 Deductions shall be made for strings, sills, lintols and the like only when

exceeding 100mm in height.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 4.0 FLOOR FINISHES

Description

4.1 The description of each item of floor finishes shall be deemed to include all temporary rules, temporary grounds, temporary screeds and the like, cutting holes, notching and the like, all normal bedding and pointing materials, providing all necessary samples, cleaning down and making good around pipes, sanitary fixtures and the like, work in narrow widths and small quantities in areas interrupted by seatings, channels and the like, all internal angles, quirks, grooves, throats, drips, coves and rounded external angles not exceeding 25mm radius, angles, stops, intersections, fair ends junctions, wreathed corners and the like on cornices, mouldings, enrichments, coves, skirtings, gutters, channels, strings, kerbs and similar or other sundry items of a like nature.

4.2 The description of each item of floor finishes shall be deemed to include

protecting surfaces from the weather or building operations.

Rate 4.3 Unless otherwise stated, rates in this section are applicable to works at

horizontal surfaces exceeding 300mm wide.

4.4 The rates for skirtings, shall be applicable to the following:- (a) Drops, risers, sides of plinths and curbs and other vertical surfaces

not exceeding 300mm high. (b) Treads, top of curbs and other horizontal surfaces not exceeding

300mm wide. Deduction

4.5 No deduction shall be made for openings of 0.50 square metre or less. 4.6 Measurement

Where an item is described as “Add to (or deduct from) ..... for each 5mm thickness over (or under) ......”, the difference for any thickness less than 5mm shall be paid/deducted based on 5mm thick.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 5.0 ROOFING

Description 5.1 The description of each item of roofing shall be deemed to include:-

a) All laps, straight, skew and circular cutting at eaves, verges, top edges, abutments, valleys and hips, cutting holes for pipes, nails, screws, clips, pellets, straps and the like.

b) Chasing the structure for burning-in or tucking in edges of

coverings, flashing and the like.

c) Holes in coverings, underbeds and insulations for pipes, standards and the like and making good.

Deduction

5.2 No deduction shall be made for voids of 0.50 square metre or less. 5.3 Membranes System and Panel Roofing System

Rate 5.3.1 Rates for Waterproofing Membranes System and Panel Roofing System

shall be held to include for narrow widths, small quantities, temporary rules, covering up, protecting after laying and cleaning on completion, all labour to form arrises, fair edges etc., all cuttings and working around pipes, dress down at eaves to form drips or carried up at abutments to walls, pipes, parapets, skirtings, concrete curbs etc. and the like.

5.4 Profiled Sheet Roofing

Description 5.4.1 The description of each item of profiled sheet roofing or cladding shall be

deemed to include all cutting at square and raking abutments, top edges, bedding and pointing eaves fillers, verges, cutting and fitting and making good around outlets, pipes and any other sundry items of a like nature.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 6.0 CARPENTRY AND JOINERY

Description 6.1 The description of each item of carpentry work shall be deemed to include

all cutting, notching, boring, sinking, pelleting, fitting, trimming, mitring, halving, morticing, tenoning, dovetailing, scarfing, wedging and all ends, splayed edges, short lengths and temporary supports and any other sundry of a like nature and also all labour in forming, drilling for bolts and fixing in position complete with nails, screws or adhesives.

6.2 The description of each item of joinery work shall be deemed to include all

nailing, gluing, screwing, plugging, cutting, notching, holes, housing ends, mitring ends and shaped ends, angles, junctions, heading joints, short lengths, tongued angles, splayed or rounded edges, chamfers, rebates, grooves and any other sundry items of a like nature including stops and working cross-grain, fitting and hanging and the like.

6.3 Nominal sizes are stated for wrot timber and an allowance of 2.5mm is

permitted for each wrot face. 6.4 Rates for windows and doors include hanging and fixing. 6.5 Where ironmongery is included in the description of doors, it shall be

deemed to include hinges, floor springs, door gears, locks, latches, catches, bolts, closers, holders, padlocks, stoppers, push-bars and plates, pull bars and handles, kickplates, locking eyes and the like as specified.

7.0 IRONMONGERY

Rate

7.1 Rates for each item shall be held to include for supply, delivery to site and fixing complete with all matching screws of the same finish as ironmongery, nails, pins or brads, cutting sinking and boring and morticing as required, oiling and easing and adjusting all moving parts, taking off and refixing after painting where necessary and handing 3 keys properly labelled to the Superintending Officer or the Superintending Officer's Representative etc unless otherwise described.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 8.0 STRUCTURAL STEELWORK AND METALWORK 8.1 Description The description of each item of work shall be deemed to include:-

a) Allowances for rolling margins and the weight of welding materials.

b) Shop and site fabrication including drilling, cutting (including holes and openings for other trades), notching, splicing, mitring, welding, riveting, bolting, machining ends and bearings, delivery, unloading, handling, assembling, hoisting, erecting, fitting and fixing in position, bedding, filling in solid, polishing and pointing including necessary lugs or other attachment.

c) Provision of all necessary construction equipment, temporary

bracing supports and the like required for erection, providing samples and tests required by the specification, the inspection of welds including the use of any special radio-graphic techniques.

d) Protection such as wrapping finished work with paper, coating with

grease or carrying out such other protective measures as may be required and removing and cleaning on completion.

e) Nuts and any type of washer which may be required.

f) Preparation of shop Drawings.

Deduction 8.2 No deduction shall be made for drillings, holes, notchings, splay cuts and

the like. Measurement

8.3 Weights stated shall be net theoretical weights. 8.4 Steel sections and plates in connections or fitted stiffeners, column cap

and base plates, rigid frame bases and butt plates, purlins, girts, eaves, fascias and similar cleats or brackets attached to trusses, lattice girders and open web joists and plates, and similar items shall be weighted at net dimensions.

8.5 Irregular, including circular shaped plates shall be weighted at the

smallest size rectangles from which they can be cut; regular and triangular shaped plates shall be weighted at net dimensions.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 8.0 STRUCTURAL STEELWORK AND METALWORK (CONT’D) 8.6 Half or other parts of steel sections in connections shall be weighted at

half the weight of the section from which they have been cut when equal to or less than half the section and at the full weight of the section from which they have been cut when greater than half the section.

9.0 WALL AND CEILING FINISHES

Rate 9.1 Rates for each item shall be deemed to include the provision of keys to

receive finishes, all temporary rules, temporary grounds, temporary screeds and the like, cramps, dowels, ties, special metal supporting brackets and the like, cutting holes, notching and the like, masking, labour to internal angles other than coved angles, making good around pipes, sanitary fixtures and the like, work in narrow widths and small quantities, joints between different types of work, joints between new and old work, internal angles, fair edges, rounded or chamfered edges or angles, quirks, grooves, V-joints, groin points and other intersections of curved surfaces, rounded coves and external angles not exceeding 25mm radius, necessary UPVC trimming pieces, mitres, stops and the like on cornices, mouldings, architraves, coves, skirtings, gutters, strings and all making good and any other sundry items of a like nature.

9.2 Rates for each item shall also be deemed to include protecting surfaces

from the weather or building operations. 9.3 Rates for each item of wall tiling shall be held to include for narrow widths

and small quantities, fittings around air bricks, pipes and the like and any other sundry items.

9.4 Rates for each item of terrazzo shall be held to include for narrow widths

and small quantities, and for all temporary rules, internal angles, arises, joints between different types of terrazzo, quirks and all making good and any other sundry items of a like nature on in-situ terrazzo, fitting around air bricks, pipes and the like and any other sundry items of a like nature on precast terrazzo.

Deduction

9.5 No deduction shall be made for openings of 0.50 square metre or less.

Measurement 9.6 In the measurement of plastering, no deduction shall be made for casings

for pipes under 300mm wide or angles which are finished in a different material if these do not exceed 100mm girth.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 9.0 WALL AND CEILING FINISHES (CONT’D) 9.7 Measurement of ceilings shall include sides and soffits of beams. 9.8 "Within the building" shall mean surfaces within the internal of

buildings/flats, corridors, staircases and the like which normally do not entail scaffolding or mechanical cradles to carry out the works.

9.9 "External face of building" shall mean surfaces such as gable end walls,

front/back external walls and any other surfaces which are constantly exposed to weather and/or which normally require the use of scaffolding or mechanical cradles to carry out the work.

9.10 Work shall be deemed to be executed when scaffolding has been

provided during the course of construction. Should scaffolding be required separately just to execute the work, it would be paid as an extra item.

10.0 SANITARY, WATER AND GAS INSTALLATION

Description 10.1 The description of each item of pipework shall be deemed to include:-

a) All short lengths, joints in the running lengths, joints to all branches, tees, sockets, sleeves, connectors, backnuts, nipples, standard pipe framings or supporting clips, saddles, fastening brackets, holderbats, straps and the like.

b) Giving notices.

c) Complying with all requirements of the relevant authorities, paying

fees and the like in connection with the installations and preparing and submitting Drawings for approval if required.

Measurement 10.2 Where an item is described as “Add to last item for each additional

150mm depth”, the difference of any depth less than 150mm shall be paid based on 150mm depth.

11.0 GLAZING

Rate 11.1 Rates for each item of glazier shall be held to include for cutting and

rounded edges, fixing panel pins, clips, brass screws and cup, neoprene strips, silicone sealants and the like and leaving the glass clean on completion

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 12.0 PAINTING AND DECORATING

Rate 12.1 Rates for each item of painting shall be held to include for all necessary

preparation of surfaces including cleaning off, knotting, stopping and sandpapering woodwork, wirebrushing metal and leaving all surfaces free from dust, rust, grease and oil before painting, narrow widths, etc.

12.2 All items in this section shall be deemed to include for multi-coloured

works.

Deduction 12.3 No deduction shall be made for openings of 0.50 m2 or less. 12.4 Work shall be deemed to be executed when scaffolding has been provided

during the course of construction. Should scaffolding be required separately just to execute the work, it would be paid as an extra item.

13.0 TURFING AND TREE-PLANTING & LANDSCAPING WORKS

Definition of Approved Soil Mixture 13.1 Approved soil mixture shall be three parts topsoil with one part of soil

conditioner and 1 kg per m3 of granular fertilizer NPK (15:15:6.4) or 4:2:1 subsoil, unwashed sand and soil conditioner with 1 kg per m3 of granular fertilizer NPK (15:15:6.4). Measurement

13.2 The measurement of girths of the trees shall be at a height of 1.0 metre above ground.

13.3 Rates

The rate for cutting down trees shall be deemed to include for grubbing up roots and filling of voids after removal of tree roots.

13.4 The rate of each item of turfing and planting shall be deemed to include

for watering, weeding, fertilizing, cutting, settlement, re-seeding and maintenance during the “Maintenance Period” as specified.

of 100

PARTICULAR PREAMBLES TO VARIOUS TRADES 14.0 DAYWORK

Rate 14.1 Rates shall be applicable in respect of all work executed on a daywork

basis. During the continuance of such work, the Contractor shall keep proper records of the names, occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and construction equipment employed. Such records, receipts or vouchers must be verified by the Superintending Officer or the Superintending Officer's Representative before payment can be effected.

of 100

HOUSING AND DEVELOPMENT BOARDSTANDARD SCHEDULE OF RATES FOR BUILDING WORKS (JUL 2013)

S/N DESCRIPTION UNIT RATE($) CODE

EXCAVATION

Excavation oversite commencing from ground levelin ordinary ground, including forming of surfaces andremoval of surplus excavated materials within site,for the following average overall depth:

1 not exceeding 150mm deep. m² $2.20 SA001

2 exceeding 150mm but not exceeding 300mm deep. m² $3.80 SA002

3 exceeding 300mm deep. m³ $11.60 SA003

4 Excavation in Embankment commencing from reducedlevel in ordinary ground including forming of surfaces andremoval of surplus excavated materials within site.

m³ $13.30 SA007

Excavate to form Trenches for Columns, Pilecaps,Foundations, Beams, Basements, Pier Holes etc inordinary ground including forming of bottom,necessary planking and strutting, part return, fill andram, and remainder get out and deposit on site asdirected in stages of the following depth:

5 not exceeding 2.00m deep. m³ $22.50 SA008

6 exceeding 2.00m but not exceeding 4.00m deep. m³ $24.10 SA009



Excavation for HARD GROUND where blasting willnot be permitted HARD GROUND is defined as:cemented sand, shale, decomposed rock or othermaterial with Standard Penetration Values notexceeding 70 blows per 30cm and bulk density notexceeding 2100kg/m3 and can be excavated by heavymachinery with a maximum breakout force of13,000kg such as Caterpillar 977L or its equivalent:




of 100



EXCAVATION (CONT'D)

Excavate to form trenches for drain lines in ordinaryground including forming of bottom, necessaryplanking and strutting, get out and deposit on site asdirected and backfill excavated trench with granitedust/fines in stages of the following depth:



Excavate to form trenches for service pipes, cablecrossings, etc. in ordinary ground including formingbottom and get out, deposit on site as directed andbackfill trench in stages of the following depths:

14 not exceeding 2.00m deep with granular materials. m³ $40.20 SA038

15 exceeding 2.00m but not exceeding 4.00m deep with ditto.

m³ $40.10 SA039

16 not exceeding 2.00m deep with selected excavated material.

m³ $16.70 SA036


m³ $16.50 SA040

18 not exceeding 2.00m deep with selected imported earth.

m³ $26.10 SA037


m³ $26.00 SA041

20 CART AWAY excavated materials off site and deposit atthe Contractor's own dumping ground.

m³ $11.90 SA016

21 Dry approved earth filling obtained from outside sourceand fill in layers of 300mm thick; including labour forspreading, trimming and consolidating to form earthmounds or to form levels outside buildings and/or underfloor slabs, etc as specified.

m³ $14.90 SA017

22 Selected excavated material obtained within the site andused as filling to make up level including consolidation.

m³ $14.80 SA018

of 100



EXCAVATION (CONT'D)

23 80mm diameter (minimum) bakau piles as roller supports. m $1.80 SA033

24 Unwashed sand including spreading, levelling andconsolidating.

m³ $64.50 SA020

25 Hardcore in beds, comprising of clean brokenbricks/concrete, deposit, spread, levelled, mechanicallyconsolidated and including 25mm thick sand or granitedust blinding/topping.

m³ $26.20 SA024

26 Granite dust, spread, level and consolidate. m³ $53.10 SA025

27 Pre-treatment of soil for the protection of building againstsubterranean termites with approved chemicals includinga layer of black polythene sheets on top of the treatedarea (treated/untreated area shall be measured flat onplan up to the perimeter of the building line excludingapron areas - rate inclusive of the provision of a 5-yearwarranty).

m² $12.20 SA027

28 Supply and delivery of Grade 43 steel sheet piles for useas temporary shoring to retain the sides of excavation inapproved section and lengths.

ton $171.30 SA028

29 Driving Grade 43 steel sheet piles including the provisionof all labour, Construction equipment (providing,assembling and subsequent dismantling of pilingequipment measured separately), tools and everythingnecessary for the installation as specified.

ton $379.50 SA029

30 Extracting, recovering and stacking Grade 43 steel sheetpiles including the provision of all labour, tools (providing,assembling and subsequent dismantling of pilingequipment measured separately), and everythingnecessary for the execution as specified.

ton $253.00 SA030

31 Grade 43 steel sheet piles left in permanently includingthe provision of all labours, tools (providing, assemblingand subsequent dismantling of piling equipmentmeasured separately), and everything necessary for theinstallation as specified.

ton $1,847.50 SA031

32 Providing and assembling of necessary piling equipmentto drive/extract Grade 43 steel sheet piles of any sizeincluding all necessary tools and appliances, subsequentdismantling and removal on completion of the work onsite.

item $8,159.30 SA032

33 Approximately 16mm nominal internal diameter hollowUPVC pipe with a prelaid 3mm diameter wire inside theUPVC pipe within each cast in-situ pile.

m $2.00 SA043

of 100



CONCRETE WORK

Mass/lean concrete to underside of foundations,ground beams, floor slabs, apron slabs, etcirrespective of thickness as specified:

34 Concrete (1:3:6). m³ $142.60 SB003

35 Concrete (1:2:4). m³ $145.00 SB002

Reinforced Concrete in foundations, ground beams,column stumps, ground floor slabs, apron slabs etcincluding working around rod or fabric reinforcementbelow ground floor level as specified (reinforcementmeasured separately):

36 Grade 20. m³ $149.30 SB004

37 Grade 25. m³ $151.60 SB006

38 Grade 30. m³ $156.10 SB008

39 Grade 35. m³ $158.50 SB111

40 Grade 40. m³ $162.10 SB113

41 Grade 45. m³ $166.80 SB116

42 Grade 50. m³ $172.80 SB118

43 Extra over grade 40 reinforced concrete for the provisionof precast pilecap formwork panels including fabricationand all necessary tie bars and clamps.

m2 $50.00 SB367

Reinforced Concrete to suspended slabs, beams,columns, staircases, walls, etc including workingaround rod or fabric reinforcement above groundfloor level as specified (reinforcement measuredseparately):

44 Grade 20. m³ $156.90 SB005

45 Grade 25. m³ $159.20 SB007

46 Grade 30. m³ $163.70 SB009

47 Grade 35. m³ $166.10 SB112

of 100



CONCRETE WORK (CONT'D)

Reinforced Concrete to suspended slabs, beams,columns, staircases, walls, etc including workingaround rod or fabric reinforcement above groundfloor level as specified (reinforcement measuredseparately) (Cont'd):

48 Grade 40. m³ $169.80 SB114

49 Grade 45. m³ $174.50 SB117

50 Grade 50. m³ $180.50 SB119

51 Approved damp proof membrane Type B (felt fibre base)to underside of reinforced concrete slab includingprovision for laps and preparation of surface as specified.

m² $10.30 SB011

52 Liquid-applied flexible cementitious or water-basedWaterproofing Membrane to bath/wc/kitchen floorsincluding upturns on pipes and walls as specified(Measured flat-on-plan and no adjustment to be made forvoids occupied by pipes).

m² $12.50 SB359

Mild Steel Rod Reinforcement, fabricated and laid infoundations, beds, suspended slab, walls, columns,beams, staircases etc, and including labour forforming stirrups, links etc:

53 6mm diameter. kg $2.50 SB022







of 100




Deformed High Tensile Steel Rod Reinforcement,fabricated and laid in foundations, beds, suspendedslabs, walls, columns, beams, staircases etc, andincluding labour for forming stirrups, links etc:











70 Extra over steel rod reinforcement for galvanising. kg $0.70 SB039

Welded steel fabric reinforcement well lapped andtied at joints (measured nett) :

71 A5. m² $4.00 SB040

72 A6. m² $5.00 SB041

73 A7. m² $6.50 SB042

74 A8. m² $8.00 SB043

of 100




Welded steel fabric reinforcement well lapped andtied at joints (measured nett) (Cont'd):

75 A10. m² $12.20 SB145

76 A12. m² $17.10 SB284

77 B5. m² $6.90 SB146

78 B6. m² $8.00 SB147

79 B7. m² $9.00 SB148

80 B8. m² $11.80 SB149

81 B8A. m² $7.00 SB352

82 B9. m² $13.90 SB229

83 B10. m² $15.80 SB150

84 B12. m² $20.80 SB151

85 B13. m² $26.10 SB350

86 D5. m² $7.20 SB346

87 D6. m² $9.30 SB048

88 D7. m² $12.00 SB049

89 D8. m² $15.40 SB124

90 D9. m² $19.20 SB230

91 D10. m² $23.80 SB231

92 D11. m² $28.50 SB347

93 D12. m² $34.00 SB348

94 D13. m² $39.90 SB349

95 Dowel Mesh (DM). m² $9.60 SB358

of 100




Prefabricated pilecap mesh reinforcement:

96 Type H1320 0840. m² $13.70 SB326

97 Type H1315 1315. m² $27.00 SB354

98 Type H1310 1310. m² $38.00 SB324

99 Type H1310 1610. m² $49.70 SB325

100 Type 2H1310 1320. m² $48.10 SB327

101 Type 2H1315 1315. m² $39.00 SB331

102 Type 2H1310 0840. m² $40.80 SB330

103 Type 2H1315 0840. m² $28.70 SB355

104 Type 2H1310 1310. m² $57.10 SB328

105 Type 2H1310 1610. m² $68.10 SB329

106 ECC mesh H1320 (Type 1) m $12.70 SB363

107 ECC mesh H1320 (Type 2) m $13.90 SB364

108 Prefabricated pilecap link mesh reinforcement. m² $21.40 SB332

Prefabricated beam stirrup cage reinforcement:

109 Reference no. S07. m² $18.50 SB280







116 Reference no. 2S130 (twin). m² $39.50 SB334

117 Prefabricated beam capping link reinforcement no R10-300.

m² $20.40 SB288

of 100




Prefabricated wall mesh reinforcement:

118 Type H1320 0820. m² $13.00 SB356

119 Type H1310 0820. m² $21.60 SB357

Prefabricated column link cage of R6 reinforcement(Reference no L36, L36A, L36B, L46, L46A, L46B, L56,L56A, L56B) :

120 at 100mm spacing. m² $8.30 SB306

121 at 150mm spacing. m² $7.00 SB307

122 at 175mm spacing. m² $6.60 SB337

123 at 200mm spacing. m² $6.40 SB308

Prefabricated column link cage of R8 reinforcement(Reference no L38, L38A, L38B, L48, L48A, L48B, L58,L58A, L58B) :

124 at 100mm spacing. m² $11.50 SB309

125 at 150mm spacing. m² $9.10 SB310

126 at 200mm spacing. m² $7.90 SB311

127 at 250mm spacing. m² $7.20 SB338

128 Timber formwork to surfaces of concrete foundations,column stumps, ground beams, ground floor slabs, etc.

m² $19.70 SB110

129 Timber formwork to surfaces of concrete columns, walls,suspended slabs, stairs, canopies, beams, lintols etc.

m² $29.00 SB062

130 Timber formwork to produce a good off-form finish tosurfaces of concrete columns, walls, slabs, beams,staircases, canopies, lintols etc. as specified.

m² $37.00 SB274

131 Formwork of approved materials to produce a good off-form finish to curved surfaces of concrete columns, walls,slabs, beams, staircases, canopies, lintols, etc. asspecified.

m² $46.50 SB275

132 LABOUR ONLY for preparing, cleaning, assembling,erecting and dismantling of metal formwork of any typesto surfaces of concrete columns, walls, suspended slabs,staircases, canopies, beams etc.

m² $29.80 SB064

of 100




PRECAST CONCRETE in sills, lintols, slabs, etcincluding moulds, hoisting and fixing in position:

133 Grade 25 with reinforcement. m³ $571.20 SB158

134 Grade 25 without reinforcement. m³ $317.40 SB159





139 Precast concrete Grade 40 in footing/stump includingmoulds, hoisting and placing in position (reinforcementmeasured separately).

m³ $286.80 SB380

140 Hacking through reinforced concrete floors or walls (anythickness) to form opening including making good andremove debris from site.

m³ $749.50 SB068

141 Breaking up existing reinforced concrete structuresincluding removing debris off the site.

m³ $138.70 SB164

142 Breaking up of existing mass concrete structuresincluding removing debris off the site.

m³ $111.10 SB165

143 One layer of approved epoxy concrete bonding agent tohacked concrete surfaces before concreting.

m² $26.70 SB166

Concrete in small quantities not exceeding 0.15m³including all necessary formwork:

144 Grade 20. m³ $395.50 SB069

145 Grade 25. m³ $399.00 SB160

146 Grade 30. m³ $405.70 SB163

147 Grade 40. m³ $414.80 SB317

of 100




Coring of holes through concrete structure includingremoval of debris off site:

148 25 to 31mm diameter x 100 to 200mm depth. no $55.70 SB190


150 25 to 31mm to diameter x 301 to 400mm depth. no $77.50 SB194



153 32 t0 49mm diameter x 301 to 400mm depth. no $70.10 SB302


















of 100




Coring of holes through concrete structure includingremoval of debris off site (Cont'd):

171 300mm diameter x 100 to 200mm depth. no $188.10 SB220



Forming bituminous expansion joint in concretefloors including all necessary formwork andbituminous seal:

174 13mm wide x 75mm deep. m $5.30 SB316

175 25mm wide x 100mm deep. m $11.80 SB096

176 Forming of 25mm wide expansion joint in cavity with foamplastic infill as specified.

m² $2.50 SB120

177 Forming of surface channel 150mm wide x 50mm deepon concrete floor slab to fall.

m $2.50 SB360

225mm wide (internal) Reinforced ConcreteSURFACE DRAIN constructed with 100mm thicksides, 100mm thick bottom and all exposed sides,bottom and arrises rendered smooth in cementmortar including all necessary excavation, formworkand lean concrete laid to fall as directed:

178 Grade 25 not exceeding 400mm deep (average) to invert and reinforced with B6 WSF reinforcement.

m $102.70 SB099

179 Add to LAST ITEM for the increase in stages of 100mm deep.

m $19.70 SB100

180 Grade 40 not exceeding 400mm deep (average) to invert and reinforced with A7 WSF reinforcement.

m $102.20 SB314

181 Add to LAST ITEM for the increase in stages of 100mm deep.

m $19.70 SB315

182 Extra over 225mm wide reinforced concrete drain forPRECAST CONCRETE INVERT.

m $2.10 SB105

of 100




183 225mm wide (internal) grade 40 precast concrete housedrain not exceeding 400mm deep (average) to invert with100mm thick sides and bottom complete withreinforcement and topping up sides with in-situ concreteincluding all necessary jointing, excavation, formwork andlean concrete and laid to falls as specified.

m $67.50 SB365

184 Add to LAST ITEM for the increase in stages of 100mmdeep.

m $4.90 SB366

185 315mm diameter UPVC pipe conforming to SS272 forconcealed drain outlet with Grade 30 concrete bed andreinforced with WSF B5 including formwork and leanconcrete (excavation measured separately).

m $91.70 SB371

Precast concrete (Grade 40) components includingall reinforcement, moulds, formwork stacking,hoisting, setting, labour and materials for jointing,testing accessories and protection, atc as specified:

186 100mm thick normal weight partition wall m² $99.60 SB130

187 90mm thick normal weight partition wall m² $93.30 SB131

188 70-90mm thick prestressed plank m² $75.20 SB381

189 70-90mm thick non-pretressed plank m² $101.00 SB383

190 250mm thick gable end wall m² $277.00 SB134

191 100-120mm facade wall without beam m² $140.60 SB132

192 Precast beam m³ $1,348.00 SB372

193 75mm thick ferrolite partition wall (designed mix asspecified)

m² $64.50 SB384

of 100



BRICKWORK AND BLOCKWORK

Brickwork in standard common bricks (size 215 x102.5 x 65mm) laid in prepacked mortar as specifiedwith 10mm joints raked 10mm deep or flush pointedas work proceeds:

194 Generally. m³ $320.60 SC005

195 One brick thick wall. m² $77.50 SC006

196 Half brick thick wall reinforced with expanded metal brickwork reinforcement.

m² $39.60 SC007

197 Half brick thick wall built honeycomb. m² $30.50 SC008

Common brickwall using modular bricks laid inprepacked mortar as specified with 10mm jointsraked 10mm deep or flush pointed as the workproceeds:

198 90mm thick reinforced with expanded metal brickwork reinforcement.

m² $34.60 SC016

199 190mm thick. m² $70.80 SC015

200 290mm thick. m² $98.20 SC044

Red facing brickwall using modular bricks laid inprepacked mortar as specified with 10mm jointsraked 10mm deep or flush pointed as the workproceeds:

201 90mm thick reinforced with expanded metal brickwork reinforcement.

m² $78.70 SC055

202 190mm thick. m² $152.10 SC062

203 Extra over common modular brickwork for using redfacing bricks to one face of the brickwall (applicable tobrickwall of thickness 190mm and above).

m² $49.80 SC017

of 100



BRICKWORK AND BLOCKWORK (CONT'D)

Glass block wall laid in premix mortar complete withpanel reinforcing, panel anchors, expansion strips,etc as specified:

204 146 x 146 x 98mm thick "Pittsburgh Corning" transparent/non-transparent glass blocks.

m² $453.70 SC047

205 Extra over item SC047 for using colour coated edge blocks.

m² $41.60 SC048

206 197 x 197 x 98mm thick "Pittsburgh Corning" transparent/non-transparent glass blocks.

m² $303.90 SC045

207 Extra over item SC045 for using colour coated edge blocks.

m² $23.40 SC046

208 145 x 145 x 95mm thick "NEG" transparent/non-transparent glass blocks.

m² $487.40 SC052

209 190 x 190 x 95mm thick "NEG" transparent/non-transparent glass blocks.

m² $324.10 SC049

Solid block wall laid in prepacked mortar asspecified:

210 70mm thick wall using 190 x 90 x 70mm solid blocks. m² $30.40 SC027

211 90mm thick wall using 190/290 x 90 x 90mm solid blocks.

m² $30.00 SC028

212 190mm thick wall using 190 x 90 x 90mm solid blocks. m² $58.70 SC030

213 Breaking up blockwork or brickwork in cement mortarincluding plaster (measured in gross thickness) andremoving debris off site.

m³ $45.20 SC031

214 Approved horizontal damp proof course Type B (felt fibrebase) to brick/block walls bedded in prepacked mortar asspecified.

m² $16.10 SC035

of 100



FLOOR FINISHES

215 Hack existing concrete surface to form keys and washclean to receive finishing.

m² $3.00 SD001

216 Extra over concrete slab for trowelling surface of floor orroof slab.

m² $1.10 SD002

217 Extra over concrete slab for compacting and trowellingsmooth surface of reinforced concrete floor slab by powertrowel.

m² $2.90 SD003

218 Extra over concrete floor or screed for the application ofapproved non-metallic hardener with power trowelledfinish including spraying a coat of approved curing agentonto the finished surface as specified.

m² $17.30 SD082

219 Extra over concrete ramp for the application of approvednon-metallic hardener with power trowelled finishincluding spraying a coat of approved curing agent ontothe finished surface and forming ring indentations asspecified (measured flat on plan).

m² $23.10 SD083

Forming 10mm wide groove lines on surfaces ofconcrete ramp:

220 At not more than 150mm apart. m² $7.20 SD104

221 Exceeding 150mm but not more than 300mm apart. m² $3.20 SD109

222 Matt finished polymer surface coating of approvedcolours over roof slab as specified. (rate inclusive of theprovision of a 5-year warranty).

m² $31.10 SD103

223 20-30mm thick non-shrink cement rendering to concretesurfaces trowelled to a smooth finish.

m² $28.70 SD105

224 10mm thick prepacked waterproof screed for kitchen,bath and WC floors as specified.

m² $8.00 SD110

225 ADD to (or deduct from) ITEM SD110 for each 5mmthickness over (or under) 10mm.

m² $2.40 SD112

226 20mm thick prepacked screed to floor trowelled to asmooth finish.

m² $11.60 SD004


m² $2.40 SD005

of 100



FLOOR FINISHES (CONT'D)

20mm thick prepacked screed to skirting, treads,risers, curbs and returns etc and trowelled to asmooth finish including coved and rounded angles:

228 Not exceeding 150mm in height/width. m $6.50 SD006

229 Exceeding 150mm but not exceeding 300mm in height/width.

m $10.30 SD007

230 ADD to (or deduct from) ITEM SD006 for each 5mm thickness over (or under) 20mm.

m $1.30 SD008


m $2.10 SD009

232 20mm thick prepacked screed to receive floor finishes. m² $9.50 SD087


m² $2.00 SD088

234 25mm thick Concrete Screed (Grade 25) with 10mmmaximum size aggregate to concrete floor surfacesfinished with steel trowelling including all necessarylabour and materials for preparation of substrate'ssurface to receive screed as specified.

m² $10.60 SD010


m² $1.70 SD011

25mm thick Concrete Screed (Grade 25) with 10mmmaximum size aggregate to skirting, treads, risers,curbs and return etc, trowelled to a smooth finishincluding coved and rounded angles and allnecessary labour and materials for preparation ofsubstrate's surface as specified:



m $11.50 SD013

238 ADD to (or deduct from) ITEM SD012 for each 5mm thickness over (or under) 25mm .

m $1.20 SD014


m $1.90 SD015

of 100




240 20mm thick granolithic paving consisting of cement, sandand granite chippings (1:1:2) to floor and trowelled to asmooth finish.

m² $12.20 SD019

241 ADD to (or deduct from) ITEM SD019 for each 5mmthickness of granolithic layer over (or under) 20mm.

m² $2.40 SD020

20mm thick granolithic consisting of cement, sandand granite chippings (1:1:2) to skirtings, treads,risers, curbs and returns etc and trowelled to asmooth surface including coved and rounded angles:



m $9.90 SD022


m $1.30 SD023


m $1.90 SD024

246 Extra over granolithic paving (irrespective of thickness)for exposed aggregate finish.

m² $10.00 SD025

247 Extra over granolithic paving (irrespective of thickness)for exposed aggregate finish all as in ITEM SD025 but forskirting etc not exceeding 150mm in height/width.

m $2.60 SD026

248 Extra over granolithic paving (irrespective of thickness)for exposed aggregate finish all as in ITEM SD025 but forskirting etc exceeding 150mm but not exceeding 300mmin height/width.

m $4.50 SD027

249 50mm thick cement rendering to floor slab including20mm thk granolithic paving consisting of cement, sandand granite chippings (1:1:1) with concrete hardenertrowelled to a smooth finish.

m² $32.30 SD116

of 100




8mm thick quarry tiles laid and bedded on andincluding necessary prepacked base screed asspecified:

250 100 x 100mm tiles. m² $48.00 SD043

251 200 x 100mm tiles. m² $45.60 SD044

252 Brick-on-edge paving using red facing modular bricks laidto approved pattern, jointed and pointed in prepackedmortar as specified (screed measured separately).

m² $76.20 SD047

253 190mm wide brick-on-edge curb using M211 red facingmodular bricks jointed and pointed in prepacked mortaras specified (screed measured separately).

m $22.30 SD054

254 190mm wide brick-on-edge curb/coping using M211 redfacing bullnose/splayed edge bricks jointed and pointedin prepacked mortar as specified (screed measuredseparately)

m $20.00 SD070

255 Grade C glazed ceramic floor tiles of approved colours,patterns and textures (nominal size 200 x 200 x 8mmthick), bedded on and including prepacked screed andpointing with approved coloured tile grouts as specified.

m² $49.10 SD092

Grade C glazed ceramic floor tiles of approvedcolours, patterns and textures (to match 200 x 200 x8mm thick tiling) to skirtings, treads, risers, curbs,nosing and returns, bedded on and includingprepacked screed and pointing with approvedcoloured tile grouts as specified:



m $18.70 SD094

of 100




258 Grade C glazed ceramic floor tiles of approved colours,patterns and textures (nominal size 300 x 300 x 9mmthick), bedded on and including prepacked screed andpointing with approved coloured tile grouts as specified.

m² $51.40 SD064

Grade C glazed ceramic floor tiles of approvedcolours, patterns and textures (to match 300 x 300 x9mm thick tiling) to skirtings, treads, risers, curbs,nosing and returns, bedded on and includingprepacked screed and pointing with approvedcoloured tile grouts as specified:



m $17.90 SD066

261 Glazed porcelain ceramic floor tiles of approved colours,patterns (nominal size 600 x 600 x 10mm thick), beddedon and including prepacked screed and pointing withapproved coloured tile grouts as specified.

m² $62.80 SD119

262 Polished porcelain ceramic floor tiles of approved colours,patterns (nominal size 600 x 600 x 10mm thick), beddedon and including prepacked screed and pointing withapproved coloured tile grouts as specified.

m² $60.90 SD120

263 Heavy duty unglazed ceramic floor tiles of approvedcolours, patterns and textures (nominal size 200 x 200 x8mm thick), bedded on and including prepacked screedand pointing with approved coloured tile grouts asspecified.

m² $56.10 SD100

Heavy duty unglazed ceramic floor tiles of approvedcolours, patterns and textures (to match 200 x 200 x8mm thick tiling) to skirtings, treads, risers, curbs,nosing and returns, bedded on and includingprepacked screed and pointing with approvedcoloured tile grouts as specified:



m $21.50 SD102

266 Heavy duty unglazed ceramic floor tiles of approvedcolours, patterns and textures (nominal size 300 x 300 x9mm thick), bedded on and including prepacked screedand pointing with approved coloured tile grouts asspecified.

m² $56.00 SD097

of 100




Heavy duty unglazed ceramic floor tiles of approvedcolours, patterns and textures (to match 300 x 300 x9mm thick tiling) to skirtings, treads, risers, curbs,nosing and returns, bedded on and includingprepacked screed and pointing with approvedcoloured tile grouts as specified:



m $19.40 SD099

269 Glazed ceramic round edge skirting tile 400x80x8mmthick of approved colour and textures bedded on andincluding prepacked screed and pointing with approvedcoloured tile grouts as specified.

m $14.70 SD115

270 Heavy duty structured/textured ceramic floor tile (nominalsize 300x300x9mm thick) bedded on and includingprepacked screed and pointing with approved colouredtile grouts as specified.

m2 $55.80 SD114

271 Heavy duty polished homogeneous floor tiles of approvedcolours, patterns and textures, (nominal size 400 x 400 x9mm thick), bedded on and including prepacked screedand pointing with approved coloured tile grouts asspecified.

m2 $60.30 SD111

272 Extra over ceramic floor tiles for prepacked waterproofscreed in lieu of prepacked screed.

m2 $1.10 SD113

Coloured interlocking concrete paving blocks toapproved pattern including 50mm thick compactedsand bed as specified:

273 224 x 110.5 x 80mm thick. m² $41.40 SD077

274 225 x 111 x 100mm thick. m² $42.80 SD078

275 453 x 453 x 100mm thick. m² $43.40 SD079

276 600 x 600 x 50mm thick concrete paving slab of grade 25concrete with 10mm max. aggregate jointed withprepacked mortar as specified.

m $17.10 SD080

277 20 x 25mm PVC "L" shaped Floor Strip laid to fall,secured to reinforced concrete floor slab with masonrynails at 500mm centre to centre and top of strip to beflushed with concrete screed as specified.

m $3.50 SD084

of 100



ROOFING

278 BRC 3315 to roof to support sisalation paper. m² $3.10 SE001

Woodwool slab to roof:

279 25mm thick. m² $43.30 SE005

280 50mm thick. m² $56.10 SE045

281 900 x 600 x 20mm thick ferrocement secondary roofslabs, reinforced with galvanised fine mesh to reinforcedconcrete flat roof including all necessary supportingconcrete solid blocks, labour and materials for sealing uppipes etc as specified.

m² $51.30 SE048

282 3mm thick acrylic polymer modified cementitious coatingto roof surfaces and gutter as specified.

m² $12.20 SE049

283 Panel Roofing System to roof surfaces consisting of38mm thick waterproofing cement and sand panel (1:3),50mm thick Styrofoam insulation board or other approvedand 6 coats of waterproofing membranes, 1 layer of openwoven glass membrane and a minimum of 20mm thickwaterproofing cement and sand screed (1:3) laid to fall asspecified and including all necessary materials for jointing(measured flat on plan - rate inclusive of the provision ofa 10 year warranty).

m² $65.90 SE008

284 One layer of "Parsec Thermo-brite II" double sidedreflective roof heat insulation sheet including lapping with"Parsec Thermo-brite" tape and secured to roof structureby self-drilling fasteners complete with metal washers asspecified and in accordance with Manufacturer'sinstructions.

m² $9.90 SE034

285 One layer of "Super Sisalation" double sided reflectiveroof heat insulation sheet including lapping with PPC 493reinforced aluminium foil tape and secured to roofstructure by self-drilling fasteners complete with metalwashers as specified and in accordance withManufacturer's instructions.

m² $8.70 SE035

286 One layer of "Super Brite" double sided reflective roofheat insulation sheet including lapping and secured toroof structure by self-drilling fasteners complete withmetal washers as specified and in accordance withManufacturer's instructions.

m² $8.40 SE047

of 100



ROOFING (CONT'D)

Colourbond XRW metal roofing sheets including allnecessary fixing accessories as specified (rateinclusive of the provision of a 10-year warranty):

287 0.47mm thick Lysaght Spandek m² $29.80 SE014

288 0.47mm thick Lysaght Trimdek m² $28.60 SE046

289 0.53mm thick Lysaght Kliplok m² $34.50 SE015

290 0.65mm thick Lysaght Kliplok m² $40.10 SE016

0.60mm thick custom made colourbond XRWflashings/cappings/trims to Kliplok/Spandek roofingincluding all necessary fixing accessories asspecified (rate inclusive of the provision of a 10-yearwarranty):

291 not exceeding 100mm girth. m $8.50 SE019

292 exceeding 100mm but not exceeding 200mm girth. m $11.90 SE020




296 0.53mm thick Lysaght Speed Deck colorbond metalroofing including all necessary fixing accessories asspecified (rate inclusive of the provision of a 10-yearwarranty).

m² $48.60 SE012

297 Colorbond ridge capping (type A) to Lysaght Speed Deckroofing including all necessary fixing accessories asspecified (rate inclusive of the provision of a 10-yearwarranty).

m $36.30 SE013

of 100



CARPENTRY AND JOINERY

Approved calcium silicate board as ceiling boardincluding corrosion resistant countersunk screwsfixed to timber joists as specified (timber joists andpainting measured separately):

298 9mm thick. m² $17.00 SF128

299 12mm thick. m² $20.70 SF049

300 Ceiling duct for concealment of discharge pipes andfittings comprising of 9mm thick calcium silicate boardwith galvanised steel angle frames, including egg cratechrome plastic lighting diffuser with powder coatedaluminium frames as specified. (measurement based onexposed surface area of duct and painting measuredseparately).

m2 $86.50 SF204

301 9mm thick calcium silicate board as box-up forconcealment of gas pipes complete with 40 x 40 x 3mmthick galvanised steel angle frames/supports as specified(painting measured separately).

m2 $60.50 SF208

302 Approved calcium silicate board with 1-hourcompartmentation as box-up for concealment of gaspipes complete with galvanised steel angleframes/supports as specified (painting measuredseparately).

m2 $101.60 SF209

303 Extra over items SF208 and SF209 for forming 15mmdiameter ventilation holes at 300mm centres.

m $1.10 SF210

304 Sawn timber in wall plates, rafters, purlins, joists, collarsand backing pieces.

m³ $1,526.90 SF004

305 Extra over structural timber for pressure impregnationtreatment with approved wood preservative.

m³ $82.20 SF005

306 Wrot timber for BOARDS under 50mm thick and 100mmor more wide including all labour and materials for anynecessary jointings.

m³ $1,471.90 SF006

307 Wrot timber for frame, head, mullion, transome or cillworked to the required shape.

m³ $1,711.50 SF007

308 Wrot timber for hand rails not exceeding 5,000 mm² insectional area.

m $21.40 SF010

of 100



CARPENTRY AND JOINERY (CONT'D)

Wrot timber for architraves, cover fillets, etc:

309 not exceeding 500 mm² in sectional area. m $2.00 SF008

310 exceeding 500 mm² but not exceeding 1,000 mm² in sectional area.

m $2.50 SF009

Wrot timber for louvre blades:

311 not exceeding 2,000 mm² in sectional area. m $4.30 SF011

312 exceeding 2,000 mm² but not exceeding 4,000 mm² in sectional area.

m $5.40 SF012

Boarding in shelving, partitions, panellings, etcscrewed on:

313 19mm thick. m² $41.50 SF013

314 25mm thick. m² $48.40 SF014

315 Teak or other approved timber hardwood strip flooringcomprising of 70mm wide x 350-450mm long x 12mmthick tongued and grooved timber strips jointed togetherand laid to approved patterns including sanding andpolishing to approval and painting surfaces with 3 coatsvarnish as specified (cement screed measuredseparately).

m2 $91.50 SF205

316 95mm high timber skirting comprising of 95mm wide x1200mm long x 11mm thick timber strips includingsanding and polishing to approval and painting surfaceswith 3 coats varnish as specified.

m $21.70 SF206

45mm thick solid cored timber door comprising of33mm thick tongued and grooved jointed boardsfixed together with 3nos 10mm diameter bolts andfilled in both faces with 6mm thick plywood lining asspecified (door frame and ironmongery measuredseparately):

317 Single-leaf door Type DT2A, D1/D1A or ST1 for opening of 1000 x 2190mm height.

no $470.00 SF096

318 Double leaf door Type DT2B or ST2 for opening of 1500 x 2190mm height.

no $707.30 SF094

of 100




38mm thick single-leaf semi-cored timber flush doorwith 6mm thick plywood lining on both faces asspecified (door frame, calcium silicate panel andironmongery measured separately):

319 Type DT1B/DF1B for opening 450 x 2190mm height. no $205.90 SF164

320 Type DT1C/DF1C for opening 500 x 2190mm height. no $209.60 SF165

321 Type HT/1 or HTF/1 for opening of 380 x 2190mm height.

no $208.00 SF192


no $209.70 SF193


no $235.20 SF194


no $259.40 SF195

of 100




325 12mm thick calcium silicate fixed panel to top of doorcomplete with supporting frames as specified.

m² $49.00 SF187

326 38mm thick semi-solid timber toilet door with highpressure plastic laminated on both sides as specified toopening size 975x2190mm (door frame and ironmongerymeasured separately).

no $349.00 SF217

327 38mm thick single-leaf solid timber bedroom door TypeDM4, DM5 and DM6 with approved veneered plywoodfacing and decorative inlays on both sides complete withvarnish as specified to opening size of 975x2190mmheight (door frame and ironmongery measuredseparately).

no $367.00 SF214

328 38mm thick single-leaf semi-solid timber bedroom doorType DM4A, DM5A and DM6A with approved veneeredplywood facing and decorative inlays on both sidescomplete with varnish as specified to opening size of975x2190mm height (door frame and ironmongerymeasured separately).

no $343.30 SF218

329 45mm thick solid timber main entrance door Type DM1,DM2 and DM3 with approved veneered plywood facingand decorative inlays on both sides and complete withmild steel door frame, varnish, approved ironmongery asspecifed to opening size of 1200x2190mm height.

no $825.70 SF216

330 45mm thick half-hour fire-rated solid timber main entrancedoor Type FDM1, FDM2 and FDM3 with approvedveneered plywood facing and decorative inlays on bothsides and complete with mild steel door frame, varnish,approved ironmongery as specifed to opening size of1200x2190mm height.

no $877.10 SF215

of 100




45mm thick double-leaf half-hour fire rated timbersurface finished composite door complete with 100 x63mm timber door frame, all necessary ironmongeryand accessories as specified:

331 Type FDT2F for opening of 1500 x 2190mm height. no $948.60 SF089

332 Type FST2 for opening of 1500 x 2190mm height. no $957.40 SF202

45mm thick single-leaf half-hour fire rated timbersurface finished composite door complete with 100 x63mm timber door frame, all necessary ironmongeryand accessories as specified (fire-rated removablepanel measured separately) :

333 Type FDT1B/FDF1B for opening of 450 x 2190mm height.

no $542.60 SF145

334 Type FDT1C/FDF1C for opening of 500 x 2190mm height.

no $551.00 SF146

335 Type FDT1E/FDF1E for opening of 650 x 2190mm height.

no $577.10 SF148

336 Type FDT1F/FDF1F for opening of 750 x 2190mm height.

no $588.00 SF149

337 Type FDT1G/FDF1G for opening of 850 x 2190mm height.

no $594.60 SF150

338 Type FDT2H for opening of 1000 x 2190mm height. no $612.70 SF091

339 Type FST1 for opening of 1000 x 2190mm height. no $664.30 SF201

340 Type FDT2J for opening of 1000 x 2190mm height with clear glass observation panel size 150 x 300mm.

no $636.30 SF092

341 45mm thick half-hour fire rated removal timber panel with3mm thick plywood finish on both sides and complete with 100x63mm thick timber frame to service duct above doorpanel.

m² $306.00 SF207

of 100




Approved waterproofed plywood in panels forshelves, partitions and the like:

342 6mm thick . m² $17.90 SF033

343 9mm thick . m² $19.80 SF034

344 12mm thick. m² $21.90 SF035

345 18mm thick. m² $26.60 SF036

346 25mm thick. m² $29.20 SF037

of 100



IRONMONGERY

Brass lever action flush bolt in satin finish:

347 200 x 20mm wide. no $10.70 SG091

348 300 x 20mm wide. no $12.10 SG092

Stainless steel shoot bolt:

349 90 x 27mm barrel/square shoot bolt. no $6.40 SG013

350 240 x 27mm barrel/square shoot bolt. no $8.70 SG014

Stainless steel lever action flush bolt:

351 225 x 25mm wide. no $9.80 SG072

352 150 x 25mm wide. no $8.50 SG073

Stainless steel lever action box type flush bolt insatin finish:

353 200 x 20mm wide. no $9.40 SG123

354 300 x 20mm wide. no $10.30 SG124

Stainless steel butt hinges (grade 304):

355 100 x 70 x 1.5/1.7/1.8mm (±0.2mm) thick. no $4.90 SG141

356 102 x 76 x 2.0mm thick. no $5.30 SG075

357 102 x 76 x 3mm thick satin finished solid brass hingeswith flat button tip and ball bearing.

no $7.80 SG090

358 Nickel plated cabinet spring hinge. no $2.30 SG137

Cabin hook and eye:

359 80mm brass. no $9.70 SG080

360 100mm stainless steel. no $13.90 SG041

4mm thick stainless steel plate locking eyes for:

361 Single leaf door. set $15.30 SG096

362 Double leaf door. set $16.70 SG093

of 100



IRONMONGERY (CONT'D)

363 95mm stainless steel bow handle. no $7.20 SG079

364 18mm diameter (min) x approximate length 225mmstainless steel pull handle Tiki PH-20/BB/225SS.

no $18.10 SG110

365 300 x 150 x 1.2mm thick stainless steel push plate. no $24.90 SG111

366 150mm stout hasp and staple. no $22.10 SG078

367 Aluminium die cast single panic bolt with extrudedaluminium guides in silver colour finish Accord 376 forsingle door complete with cylinder panic lock.

no $244.70 SG116

368 Solid brass magnetic door holder. no $11.70 SG136

369 Antique brass finish door viewer. no $8.70 SG040

370 Slim line door closer with cushioned back checking actionas specified.

no $49.50 SG142

371 Rebated 5 pin double cylinder mortice lockset completewith brass chromium plated/stainless steel handle asspecified.

no $80.70 SG143

372 Rebated 5 pin single cylinder antique brass mortice leveron backplate lockset complete with thumb turn and solidbrass lever handles on both sides for entrance door asspecified.

no $87.00 SG144

373 Cylinder mortice night latch with chromium plated finishincluding the provision of keys as specified.

no $93.40 SG145

374 Antique brass finish lever handle lockset with 5-pin singlecylinder and thumb turn (key on outside and thumb turnon inside) with lever handles on both sides for bedroomdoor as specified.

no $72.70 SG150

375 Antique brass finish lever handle lockset with emergencyrelease on outside and thumb turn on inside with leverhandles on bothsides for bathroom door as specified.

no $68.50 SG151

376 Antique brass finish 5 pin tumbler single cylinder knobset(with key on the outside and push button on the inside)for bedroom door as specified.

no $28.70 SG139

377 Antique brass finish privacy knobset with emergencyrelease on the outside and push button on the inside forbathroom door as specified.

no $26.10 SG138

378 Privacy knobset with emergency release as specified. no $23.10 SG146

379 Cylinder deadlock as specified. no $93.40 SG147

of 100



IRONMONGERY (CONT'D)

Padlock under master key as specified:

380 Union 3104-50mm. no $15.50 SG061

381 Union 3142. no $31.10 SG062

382 Union 3122/2 PL. no $16.60 SG106

383 Yale 110.30. no $12.90 SG063

384 Yale 110.50. no $17.90 SG105

385 Yale 110.60. no $25.00 SG064

386 Abloy 330C/25. no $32.10 SG065

387 Abloy 320C/20. no $32.10 SG127

388 Abloy 330C/25 under key alike series. no $45.00 SG095

389 Stainless steel cup handle as specified. no $12.20 SG148

390 Stainless steel cup handle passage latch with cuphandles on both sides as specified.

no $30.30 SG149

391 Brass rebated part for lockset. no $12.10 SG094

of 100



STRUCTURAL STEELWORK & METALWORK

Galvanised steel Class 'A' pipe bent to shape andfixed as rails including necessary bends, tees, etcwelded (masonry work measured separately):

392 50mm diameter. m $14.20 SH469

393 40mm diameter. m $11.00 SH470

394 30mm diameter. m $9.70 SH471

395 20mm diameter. m $7.40 SH472

396 Galvanised wrought iron holdfast 25x230x3mm, one endscrewed to door or window frames and the other endfishtailed and built into joints of brick or block walls, orcast into reinforced concrete walls/columns.

no $1.80 SH410

397 Heavy duty hot-dipped galvanised steel gratingcomprising of 65x9mm thick flats as framing, 65x9mmthick intermediate flats spaced at 30mm centres restingon 12mm diameter rods at 85mm centres and supportingon 75x75x9.4mm thick angle frame anchored to concretestructure with mild steel fish tail.

m² $888.60 SH475

398 Heavy duty hot-dipped galvanised steel gratingcomprising of 65x9mm thick flats as framing, 50x9mmthick intermediate flats spaced at 30mm centres restingon 10mm diameter rods at 75mm centres and supportingon 75x75x9.4mm thick angle frame anchored to concretestructure with mild steel fish tail.

m² $807.50 SH590

399 Heavy duty hot-dipped galvanised steel gratingcomprising of 65x10mm thick flats as framing, 55x10mmthick intermediate flats at 30mm centres resting on 10mmdiameter bars at 75mm centres and supporting on75x60x8mm thick angle frame anchored to concretestructure with mild steel fish tail.

m² $748.90 SH714

400 300mm wide hot dipped galvanised steel grating overapron drain comprising of 50x8mm thick galvanised steelflats as framing infilled with 10 nos 25x6mm thickgalvanised steel flats resting on 25x6mm thick galvanisedsteel flat supports at 200mm centres as specified.

m $87.40 SH658

of 100



STRUCTURAL STEELWORK & METALWORK (CONT'D)

401 300x600mm hot dipped galvanised steel hinged gratingover apron drain comprising of 32x9mm thick galvanisedsteel flats as framing infilled with 9 nos 25x6mm thickgalvanised steel flats resting on 2 nos 25x6mm thickgalvanised steel flats and supported on 64x38x4.5mmthick galvanised steel angle frame anchored to concretestructure as specified.

no $72.20 SH659

402 300x600mm hot-dipped galvanised hinged gratingcomplete with 3mm thick galvanised mild steel chequeredplate over reinforced concrete apron drain as specified.

no $70.20 SH568

403 0.8mm thick galvanised steel motorised roller shutter(with ventilation holes) finished with colourbond siliconemodified polyester coating complete with channel guide,shutter motor, angle bolts, bottom rail, auto-stop safetydevice, push-button switches in weatherproof control boxwith utility lock and all necessary components inaccordance with Manufacturer's instructions tocentralised refuse chamber with approximate overall size3400mm (min) wide x 3800mm height to underside ofmotor casing.

no $3,780.00 SH411

404 0.5mm (minimum) thick zincalume steel motorised rollershutter (with ventilation holes) finished with colourbondsilicone modified polyester coating complete with channelguide, shutter motor, angle bolts, bottom rail, auto-stopsafety device, push-button switches in weatherproofcontrol box with utility lock and all necessary componentsin accordance with Manufacturer's instructions tocentralised refuse chamber with approximate overall size3400mm (min) wide x 3800mm height to underside ofmotor casing.

no $3,984.80 SH489

405 Galvanised steel grille panel over parapet at staircase &access balcony comprising of 50x50x1.6mm thick hollowsection frame filled in with 18x9mm thick flats spaced atnot more than 100mm centres welded on to frame andthe panel fixed to wall with 38x9mm fishtail holdfast.

m2 $156.30 SH707

406 Galvanised steel railing 900mm high at staircasecomprising of 18x9mm thick flat baluster spaced at notmore than 100mm centres and 25x25x1.6mm thick hollowsection supports at not more than 1200mm centres, allwelded to 43mm diameter x 1.6mm thick hollow sectionhandrail and 38x9mm thick flat bottom rail and thesupport cast into concrete curb.

m $114.90 SH708

of 100




407 Galvanised steel grille panel comprising of 50x50x6mmthick hollow section framings filled in with 19x10x1.2mmthick hollow section members welded to the frame andpanel fixed to wall with 25x25x2.2mm thick hollow sectionsupports.

m² $106.10 SH587

408 Mild steel Grade 43A for flats, angles, tees, channels,hollow sections, square sections, rivets and bolts, etc. ofany size fabricated and fixed including welding or bolting,and painting with one coat of lead and chromate-freeprimer (for structural steel work only).

kg $6.70 SH018

409 Mild steel flats, angles, tees, channels, rivets and bolts,etc. of any size fabricated and fixed including welding orbolting (for non-structural steel work only).

kg $4.90 SH019

410 Extra over mild steel rods, flats, angles, tees, channels,hollow sections, rivets, bolts, etc for galvanising in lieu ofpainting one coat of lead and chromate-free primer.

kg $0.40 SH670

411 Extra over mild steel rods, flats, angles, tees, channels,hollow sections, rivets, bolts, etc for galvanising.

kg $0.70 SH584

412 13mm diameter mild steel fan hook to concrete surface ofceiling.

no $7.50 SH022

413 Ramset Nail No.2330 or equal and approved includinguse of gun and explosive charges.

no $0.70 SH023

414 Mild steel blast door BD4 for household shelter completewith mild steel door frames, hinges, locking device,stainless steel handles ventilation sleeve and plate units,etc including approved primer as specified.

no $1,221.90 SH671

415 Wrought iron steel gate Type MG1A, MG2A and MG3Afixed to metal door frame of entrance door of openingsize 1200x2190mm height complete with approvedironmongery, wrought iron house number plate andpainting as specified.

no $552.00 SH715

of 100




Mild steel door frame fixed into door openings inaccordance with Board's Standard Drawingsincluding one coat of approved primer and allnecessary fittings and hinges, all as specified:

416 90 x 45 x 1.6mm thick jamb to opening size 900mm width x 2190mm height.

no $94.40 SH062


no $110.20 SH073


no $134.60 SH084

3.175mm B.G. x 50mm PVC coated mesh Chain LinkFencing of the following heights, to top of mesh with3 nos. horizontal lines of double strand 2.517mm B.G.galvanised barbed wire above at 100mm centres, thechain link and barbed wires fixed to and including50x50x6mm angle iron posts at 3m centres with topbent to form spurs and bottom cast in300x300x450mm deep concrete (1:3:6) foundationsincluding all necessary straining and tying wires andsplit pins and priming and painting posts with onecoat aluminium paint:

419 1.20m high. m $36.40 SH009

420 1.50m high. m $39.60 SH011

421 1.80m high. m $44.80 SH013

422 2.10m high. m $48.80 SH015

423 2.40m high. m $63.70 SH017

424 625mm high fluorocarbon coated aluminium sunbreakercomprising of 50.8mm diameter x 3mm thick aluminiumCHS frames filled in with 3mm thick aluminium perforatedsheets and fixed according to PE's recommendations asspecified (rate inclusive of the provision of 10-yearwarranty).

m $157.30 SH672

425 0.7mm thick aluminium false ceiling comprising of 600 x600mm double coated polyester stove enamelled colouraluminium tiles complete with all fixing accessories,suspension hangers, etc in accordance to Manufacturer'sinstructions.

m² $106.50 SH585

426 3mm thick aluminium chequered plate cover to bulk metersump complete with stainless steel handle, hinges andwelded to and including galvanised steel frames.

m2 $265.60 SH709

of 100




Natural anodised aluminium door comprising of 97 x42 x 2.3mm thick natural anodised aluminium top railand stiles, and 120x42x2.3mm thick middle andbottom rails filled in with 2.3mm thick naturalanodised aluminium louvres complete with 2.3mmthick galvanised steel door frame and all necessaryironmongery and accessories as specified:

427 Single leaf door Type DT5 for opening of 900 x 2190mm height.

no $1,396.20 SH420

428 Double-leaf door Type D7A for opening of 1500 x 2190mm height.

no $2,242.20 SH479

Natural anodised aluminium door comprising of 40 x30 x 3mm thick aluminium stiles, top, bottom andintermediate rails covered with 2mm thick aluminiumflat sheet on both faces and fill in with rockwool(density: 60kg/m³) complete with 2.3mm thickaluminium door frame and all ironmongery andaccessories as specified:

429 Single-leaf door Type DT2G/DT2J for opening of 1000 x 2190mm height.

no $1,474.70 SH599

430 Double-leaf door Type DT2E for opening of 1500 x 2190mm height.

no $2,364.10 SH597

Natural anodised aluminium door comprising of 100 x42 x 2.3mm thick aluminium stiles, top, bottom andintermediate rails covered with 2mm thick aluminiumflat sheet on both faces complete with 2.3mm thickaluminium door frame and all ironmongery andaccessories as specified:

431 Single-leaf door Type STM1 for opening of 1000 x 2190mm height.

no $1,764.50 SH681

432 Double-leaf door Type STM2 for opening of 1500 x 2190mm height.

no $2,795.20 SH682

of 100




Natural anodised aluminium door comprising ofaluminium supports and bracings covered with 2mmthick aluminium flat sheet on both faces and filled inwith rockwool complete with aluminium refusehopper, fixed aluminium louvred vent and 2.3mmthick aluminium door frame and all ironmongery andaccessories as specified:

433 Single leaf door Type DT6 for opening of 1000 x 2190mm height.

no $2,408.00 SH600

434 Double-leaf door Type DT6B for opening of 1500 x 2190mm height.

no $3,514.30 SH602

Heavy duty natural anodised aluminium louvred doorfor ESS comprising of 2.3mm thick aluminiumlouvres complete with 2mm thick aluminium doorframe including ironmongery all as specified:

435 Double-leaf door Type ALD/1 for opening of 2700 x 2700mm height.

no $3,045.30 SH574

436 Double-leaf door Type ALD/2 for opening of 1800 x 2900mm height.

no $2,386.10 SH579

Heavy duty natural anodised aluminium flush door forESS complete with 2mm thick aluminium door frameincluding ironmongery all as specified:

437 Single-leaf door Type AFD/3 for opening of 900 x 1500mm height.

no $1,491.20 SH711

438 Double-leaf door Type AFD/4 for opening of 1800 x 1500mm height.

no $2,429.80 SH712

439 Single-leaf door Type AFD/5 for opening of 900 x 2200mm height.

no $1,638.30 SH713

Bronze anodised aluminium louvred vent at serviceduct complete with frame filled in with 2.3mm thickextruded aluminium louvred blades for:

440 Opening size 615 x 400mm height. no $117.30 SH605

441 Opening size 310 x 900mm height. no $144.80 SH606

of 100




442 Three-way natural anodised aluminium letter box with anti-junk mail device in accordance with Board's StandardDrawings including master doors, locks and keys andengraving with house numbers, block numbers and streetname to top frame of letter box (masonry work measuredseparately).

no $89.10 SH717

443 Block number numeral size 500mm high x 35mm deepmade to profile, with 1.5mm thick bronze anodisedaluminium sheet and fixed to wall with aluminiumextruded sections as specified.

no $44.30 SH559

Anodised aluminium motorised roller shutter (withventilation holes) with channel guide, shutter motor,angle bolts, bottom rail, auto-stop safety device, push-button switches in weatherproof control box withutility lock and all necessary components inaccordance with Manufacturer's instructions:

444 Approximate size 3400mm wide (min) x 3800mm height to underside of motor casing for centralised refuse chamber comprising of 1.6mm thick extruded aluminium curtain interlocking slats.

no $3,910.00 SH412

445 Approximate size 2100mm wide (min) x 2100mm height to underside of motor casing for utilities centre comprising of 1.6mm thick extruded aluminium curtain interlocking slats.

no $1,000.50 SH607

446 Aluminium alloy inspection door overall size 550 x 800mmcomprising of 1.2mm thick aluminium sheets to bothfaces supported with aluminium "C" channel bracingscomplete with aluminium frames, 100mm stainless steelbutt hinges and cam lock to manufacturer's details.

no $389.90 SH414

of 100




447 40mm thick inspection cover for refuse chute overall size1140 x 1140mm to top of refuse chute comprising of1.2mm thick anodised aluminium alloy sheets on bothfaces supported with 1.2mm thick galvanised steel "C"channel bracings and infilled with rockwool insulationcomplete with 5mm thick extruded aluminium sectionframings including stainless steel friction stay, hinges andhot dipped galvanised steel safety mesh supported ongalvanised steel angle, etc to manufacturer's details.

no $616.60 SH413

448 Aluminium catladder approximately 355mm widecomprising of aluminium 'U' channel handle, 25mmdiameter tubular aluminium rungs, complete withaluminium hooks, brackets, rubber cappings and allnecessary fixing accessories as specified.

m $100.30 SH586

449 Aluminium retractable ladder overall 2900mm longcomprising of aluminium 'C' channel, aluminium hooks,25mm diameter aluminium rungs spaced at 305mm apartand complete with 2 sets of aluminium fixing bracketsincluding all necessary fixing accessories as specified.

no $279.10 SH129

450 Aluminium retractable ladder overall 5700mm longcomprising of aluminium 'C' channel, aluminium hooks,25mm diameter aluminium rungs spaced at 305mm apartand complete with 5 sets of aluminium fixing bracketsincluding all necessary fixing accessories as specified.

no $959.40 SH130

451 Aluminium cage guard comprising of 6 nos. of 32mmdiameter (external) aluminium pipes spaced not morethan 650mm apart with 38x6mm thick vertical aluminiumflats rivetted to pipes and including all necessary fixingaccessories as specified.

no $177.20 SH131

452 Purpose made aluminium handrails of overall 1000mm(approx) height to roof top access opening comprising of32mm diameter (external) aluminium pipe bent to shapeand welded with 10mm thick aluminium plates andincluding all necessary fixing accessories as specified.

pr $392.60 SH132

453 Bronze anodised extruded aluminium framed adjustablelouvred vents complete with aluminium 'U' clips/holders,6mm thick obscure wired rough cast glass louvres and allnecessary fixing and jointing materials and accessoriesas specified (measurement based on size of opening).

m² $404.50 SH677

of 100




454 Bronze anodised extruded aluminium framed fixedlouvred vent complete with 2.3mm thick extruded bronzeanodised aluminium louvred blades, and all necessaryfixing and jointing materials and accessories as specified(based on size of opening).

m² $387.50 SH678

Bronze anodised extruded aluminium framed windowcomplete with 5mm thick green grey/grey tinted floatglass and ironmongery and all necessary fixing andjointing materials and accessories as specified(measurement based on size of opening):

455 Top hung casement window. m² $469.20 SH673

456 Top and side hung casement windows. m² $364.50 SH674

457 2-track sliding window with top hung casement. m² $302.40 SH675

458 3-track sliding window with top hung casement. m² $301.90 SH676

459 Bronze anodised extruded aluminium framed sliding doorcomplete with 6mm thick green grey/grey tinted floatglass, ironmongery and jointing materials and accessoriesas specified (measurement based on size of opening).

m² $240.10 SH680

460 Bronze anodised extruded aluminium framed fixedlouvred vent for ESS complete with 2.3mm thick extrudedbronze anodised aluminium louvred blades and allnecessary fixing and jointing materials and accessoriesas specified (measurement based on size of opening).

m² $456.50 SH706

of 100




2mm thick natural anodised aluminium sign platewith helvetica medium letters and figures/symbolsengraved in black/red colour including fixing withstainless steel screws as specified:

461 200/220 x 25mm services duct signage. no $13.20 SH480

462 300 x 300mm 'No Smoking' sign plate. no $21.00 SH582

463 700mm to 1000mm long x 120mm high sign plates for services rooms.

no $36.20 SH468

464 700mm to 1000mm long x 120mm high warning sign plate for consumer switch room.

no $36.20 SH142

2mm thick natural anodised aluminium sign platewith folio caravelle bold letters and figures/symbolsengraved in red colour including fixing with stainlesssteel screws as specified :

465 70mm height x width of door leaf (approximately 290mm to 790mm) with the wordings "Wet Rising Main Outlet", "Dry Rising Main Inlet", "Fire Hose Reel" or "Down Comer Outlet".

no $23.00 SH660

466 130mm height x width of door leaf (approximately 290mm to 790mm) with the wordings "Wet Rising Main Outlet", "Dry Rising Main Outlet", "Wet Rising Main Inlet", "Dry Rising Main Inlet" or "Down Comer Outlet".

no $25.30 SH661

Signplate to multi-storey carpark comprising of 2mmthick natural anodised aluminium plate withapproved Engineer's grade reflective sheets withhelvetica medium letters and figures/symbols fixed towall as specified:

467 450 x 250mm. no $28.00 SH704

468 450 x 450mm. no $53.00 SH591

469 600 x 250mm. no $36.60 SH705

470 600 x 450mm. no $58.20 SH592

of 100




471 Height limit signboard comprising of 600 x 600 x 2mmthick aluminium plate with approved Engineer's gradereflective sheets and letterings on one face mounted onand including 50 x 50 x 6mm thick mild steel hollowsection with base plate set in concrete (1:2:4) foundationand all necessary excavation as specified.

no $216.10 SH593

472 External clothes drying racks consist of stainless steelclothes drying racks extrusion with 3 nos of fixed stainless steel poles, bend sections and all necessary componentsfixed to structure as specified,

set $609.50 SH112

473 Internal retractable clothes drying racks consist ofaluminium extrusion poles (for ceiling mounted); brackets,links, fasteners and all necessary components fixed tostructure as specified.

set $526.10 SH113

474 Complete set of clothes drying racks at recess areacomprising of 2 nos aluminium racks and stainless steelrailings of approximate size 2800 x 1250mm height asspecified.

set $948.80 SH571

2mm thick grade 304 hair-line finish stainless steelplate signage with letterings and graphics engraved,all as specified:

475 200 x 200mm signage for central refuse chute. no $19.60 SH416

476 300 x 300mm plaque at 1st storey lift entrance. no $28.40 SH417

477 Foot-operated grade 304 stainless steel refuse chutehopper to centralised refuse chute complete with allnecessary fixing accessories as specified.

no $862.50 SH476

of 100




Stainless steel pipe for railing purposes including allnecessary cutting, welding, polishing, bending toshape and fixing on site.(Measurement based onlength of stainless steel pipes)

478 19.1mm diameter x 1.0mm thick. m $32.60 SH687










Stainless steel square tube for railing purposesincluding all necessary cutting, welding, polishing,bending to shape and fixing on site. (Measurementbased on length of stainless steel square tube)

488 19.1mm x 19.1mm x 1.2mm thick. m $37.20 SH697






494 Stainless steel flats, angles, plates, channels, bolts, etcincluding cutting, welding, polishing and fixing on sitecomplete with other fixing accessories.

kg $26.10 SH703

of 100




Galvanised heavy duty expansion anchor boltincluding stud anchor, nut and washer :

495 8mm anchor diameter x 95mm long (Hilti HSL 3M8/20).

no $14.70 SH346


no $16.10 SH347


no $17.20 SH348


no $23.50 SH349


no $26.00 SH350


no $61.10 SH351


no $73.40 SH352

502 M10 x 108mm length (Ramset SA10108). no $11.70 SH353











of 100




Galvanised medium duty expansion anchor boltincluding stud anchor, nut and washer :

513 6mm anchor diameter x 65mm long (Hilti HSA M6x65).

no $2.80 SH365


no $4.80 SH366


no $4.90 SH367


no $5.20 SH368


no $5.60 SH369


no $6.50 SH370


no $7.20 SH371


no $10.00 SH372


no $10.00 SH373


no $15.10 SH374

523 6mm anchor diameter x 45mm long (Ramset Trubolt T6045).

no $2.10 SH375


no $2.20 SH376


no $4.20 SH377


no $2.50 SH378


no $2.20 SH379

of 100




Galvanised medium duty expansion anchor boltincluding stud anchor, nut and washer (Cont'd):


no $4.20 SH380


no $4.80 SH381


no $2.40 SH382


no $2.40 SH383


no $4.40 SH384


no $5.20 SH385


no $4.70 SH386


no $4.80 SH387


no $5.60 SH388


no $5.70 SH389


no $6.40 SH390


no $8.30 SH391


no $9.10 SH394


no $12.20 SH396


no $16.80 SH398

of 100




Chemical Adhesive Galvanised stud anchor includinganchor rod, nut and washer :

543 8mm anchor diameter x 110mm long with chemical capsules (Ramset M8110/CHEM8).

no $5.90 SH399


no $7.00 SH400


no $8.50 SH401


no $10.60 SH402


no $20.70 SH403

548 8mm anchor diameter x 80mm long with adhesive capsule (Hilti HAS M8 + HVU).

no $12.20 SH404


no $14.60 SH405


no $17.20 SH406


no $23.70 SH407


no $33.40 SH408


no $42.20 SH409

Chemical Capsule all to manufacturer's instructions:

554 Hilti HVU M8. no $7.80 SH553

555 Hilti HVU M10. no $9.30 SH554

556 Hilti HVU M12. no $10.60 SH555

557 Hilti HVU M16. no $13.70 SH556

558 Hilti HVU M20. no $17.20 SH557

559 Hilti HVU M24. no $19.00 SH558

of 100



WALL AND CEILING FINISHES

560 Hack existing concrete surface to form keys and washand clean to receive finishes.

m² $4.50 SI001

Skim coat of approved skimming materials appliedfrom within the building:

561 To wall. m² $5.90 SI002

562 To ceiling. m² $6.40 SI004

Skim coat of approved skimming materials appliedfrom the external face of the building:

563 To wall. m² $7.10 SI003

564 To sides and soffit of beam and slab. m² $7.60 SI005

565 Skim coating to external RC surfaces in two coats to amaximum total thickness of 6mm using approvedskimming materials as specified.

m² $17.20 SI035

566 Two coats of polymer compound and cement (1:2)mixture (total thickness 2.5mm) to concrete blockwall.

m² $6.60 SI029

567 18mm thk plastering with approved PREPACKEDMORTAR MIX to RC surfaces, brickwalls and blockwallsetc., applied from within the building as specified.

m² $21.30 SI037

568 18mm thk plastering with approved PREPACKEDMORTAR MIX to RC surfaces, brickwalls and blockwallsetc., applied from the external face of the building asspecified.

m² $24.90 SI038

569 Extra over plastering for forming 20 x 15mm deep groovelines to walls, columns, beams, etc as specified.

m $3.80 SI032

570 Pattern coloured glazed wall tiles size (200 to 300)mm x(200 to 300)mm x 7mm thick of approved colours,patterns and texture to walls including prepacked mortarscreed as specified.

m² $54.60 SI039

571 Pattern coloured glazed wall tiles size 400mm x 200mm x7mm thick of approved colours, patterns and texture towalls including prepacked mortar screed as specified.

m² $55.60 SI040

572 Pattern coloured glazed wall tiles size 600mm x 300mm x7mm thick of approved colours, patterns and texture towalls including prepacked mortar screed as specified.

m² $59.70 SI041

573 Extra over pattern coloured glazed wall tiles for laying onecourse of Listello tiles size 198 x 65mm high.

m $9.80 SI036

of 100



WALL AND CEILING FINISHES (CONT'D)

First quality grade Y glazed ceramic tiles of approvedcolours, patterns and textures to walls includingprepacked mortar screed as specified:

574 200 x 200 x 8mm thick (nominal size). m² $52.90 SI033

575 Polished homogeneous ceramic tiles of approvedcolours, patterns and textures (nominal size 300 x 300 x9mm) to wall surface including prepacked mortar screedas specified.

m² $66.70 SI034

of 100



SANITARY, WATER AND GAS INSTALLATION

UPVC pipe for rainwater fixed to wall with collarbrackets as specified:

576 200mm diameter. m $32.30 SJ324

Extra over UPVC rainwater downpipe for fittings:

577 200mm diameter connector piece. no $40.20 SJ329

578 200 x 50mm diameter junction. no $38.00 SJ387

579 200mm diameter x 275 x 120 mm adaptor. no $129.50 SJ326

UPVC fittings for rainwater downpipe :

580 120 x 275mm rectangular elbow. no $143.90 SJ327

581 Rectangular 'Y' branch junction. no $143.90 SJ328

UPVC pipe for rainwater outlet embedded in concretefloor (concrete measured separately):

582 200 x 80 x 5mm thick rectangular pipe. m $33.20 SJ331

583 275 x 120 x 5mm thick rectangular pipe. m $40.50 SJ330

584 UPVC screw-down domical grating to top of 200mmdiameter pipe complete with 240 x 240mm square body.

no $42.30 SJ325

UPVC pipe for underground sewer with flexible jointslaid on concrete bed in trench (trench and concretebed measured separately) :

585 100mm diameter. m $11.90 SJ390

586 150mm diameter. m $15.60 SJ391

587 200mm diameter. m $26.80 SJ392

Extra over UPVC sewer pipe for fittings:

588 100mm diameter bend (all angles). no $7.60 SJ393

of 100



SANITARY, WATER AND GAS INSTALLATION (CONT'D)

Extra over UPVC sewer pipe for fittings (Cont'd):

589 100mm diameter Y-junction. no $16.10 SJ394





UPVC pipe Class D for soil, waste, ventilation,discharge stacks and down pipes fixed to wall orceiling with collar brackets :

594 80mm diameter. m $19.50 SJ428

595 100mm diameter. m $21.30 SJ399

596 150mm diameter. m $33.60 SJ400

UPVC pipe for soil, waste,ventilation, dischargestacks and down pipes fixed to wall or ceiling withcollar brackets :

597 32mm diameter. m $8.20 SJ401

598 50mm diameter. m $9.40 SJ402

599 80mm diameter. m $13.90 SJ403

600 100mm diameter. m $17.40 SJ404

601 150mm diameter. m $20.40 SJ405

Extra over UPVC soil, waste, ventilation, dischargestacks and down pipes for fittings:


603 50mm diameter bend (all angles) - with double-locking device.

no $6.20 SJ407


no $10.10 SJ408

605 80mm x 50mm diameter junction. no $13.30 SJ409

of 100




Extra over UPVC soil, waste, ventilation, dischargestacks and down pipes for fittings (cont'd) :


no $9.50 SJ410

607 100mm diameter single junction - with double-locking device.

no $16.30 SJ411

608 100mm diameter double junction. no $20.80 SJ412

609 100mm x 50mm diameter single junction - with double-locking device.

no $17.50 SJ413

610 100mm x 50mm diameter double junction - with double-locking device.

no $26.20 SJ414

611 100mm x 80mm diameter single junction. no $13.60 SJ415

612 100mm x 80mm diameter double junction. no $22.60 SJ416


614 150mm diameter single junction. no $27.00 SJ418

UPVC fittings for soil, waste, ventilation, dischargestacks and down pipes :

615 80mm diameter adaptor. no $11.50 SJ422



Extra over UPVC soil, waste, ventilation, dischargestacks and down pipes for fittings Class D :

618 100mm x 80mm diameter level invert taper. no $8.90 SJ425

619 150mm x 100mm diameter level invert taper. no $11.40 SJ426

UPVC end cap to waste pipe :

620 50mm diameter. no $3.60 SJ296



of 100




UPVC waste outlet to 50mm diameter waste pipecomprising of 110 x 110mm square base includingjointing to pipe and setting on concrete floor:

623 With dome-shaped screw-in grating cover. no $9.00 SJ271

624 With flat round screw-in grating cover. no $6.20 SJ333

UPVC downspout outlet with dome-shaped screw-ingrating complete with all necessary accessories andsetting in cement mortar as specified:

625 With 150 x 150mm square base to 80mm diameter pipe.

no $13.70 SJ231

626 With 200 x 200mm square base to 100mm diameter pipe.

no $18.50 SJ232

627 150mm diameter UPVC gully trap complete with hopperand 150 x 150mm UPVC grating with screw-in roundgrating cover and filter including jointing to waste pipeand encasing in concrete.

no $88.90 SJ265

628 100mm diameter UPVC floor waste complete with hopperand 150 x 150mm UPVC grating with screw-in roundgrating cover and filter including jointing to waste pipeand encasing in concrete.

no $58.00 SJ268

629 Anti-mosquito device to floor and gully traps as specified. no $2.60 SJ368

of 100




100mm diameter UPVC floor trap complete with 150 x150mm UPVC hinged grating with round gratingcover including jointing to waste pipe:

630 'S' trap - with double-locking device. no $38.90 SJ264

631 'P' trap - with double-locking device. no $34.30 SJ349

UPVC socket sleeve to reinforced concrete flooropening:




UPVC vent cowl to top of pipe as specified:



Ductile iron pipe with cement lining laid on concretebed in trench (trench and concrete bed measuredseparately):

637 80mm diameter. m $43.90 SJ033

638 100mm diameter. m $38.40 SJ034

639 150mm diameter. m $52.10 SJ035

Extra over ductile iron pipe for:




of 100




643 80mm diameter stainless steel washout connecting pipe350mm long with stainless steel flange at one end andwelded with and including 150mm diameter x 9mm thickstainless steel collar at mid-length and cast in reinforcedconcrete structure.

set $347.50 SJ027

644 28mm diameter stainless steel overflow warningconnecting pipe 400mm long welded with and includingstainless steel collar at mid-length and cast in reinforcedconcrete structure.

set $93.50 SJ028

645 15mm diameter stainless steel flexible connecting pipe400mm long welded with and including stainless steelcollar at mid-length and cast in reinforced concretestructure.

set $8.50 SJ261

Grade 30 concrete bed and haunching to drain pipecomplete with 40mm thick lean concrete and allnecessary formwork (drain pipes measuredseparately):

646 400mm wide x overall 400mm thick to 100mm diameter pipe reinforced with A10 WSF reinforcement.

m $49.70 SJ347

647 400mm wide x overall 400mm thick to 100mm diameter pipe reinforced with B10 WSF reinforcement.

m $51.00 SJ334

648 400mm wide x overall 400mm thick to 100mm diameter pipe reinforced with B10 WSF reinforcement and 2 nos T13 reinforcement bars.

m $55.20 SJ029


m $58.50 SJ348

650 450mm wide x overall 450mm thick to 150mm diameter pipe reinforced with B10 WSF reinforcement.

m $59.90 SJ335

651 450mm wide x overall 450mm thick to 150mm diameter pipe reinforced with B10 WSF reinforcement and 2 nos T13 reinforcement bars.

m $64.20 SJ030


m $67.40 SJ386

of 100




Reinforced Concrete Grade 30 inspectionchamber/sump comprising of 150mm thick walls andbottom slab, 200mm thick top slab includingnecessary reinforcement and formwork completewith granolithic concrete benching, half roundvitrified clay main and branch channels, cementplastering to internal walls, lean concrete base andexcavation (inspection chamber/sump cover andframe measured separately):

653 Overall size 1200 x 1000 x 1070mm deep to invert. no $832.30 SJ298

654 Add to last item for each additional 150mm depth. no $80.90 SJ299



657 Overall size 1800 x 1000 x 1070mm deep to invert. no $1,093.60 SJ302










of 100




667 Precast concrete inspection chamber size900x700(internal)x1070mm deep to invert complete withreinforcement, granolithic concrete benching, channels,cast-in-situ concrete topping and excavation (structuralbeam supports, inspection chamber cover and framemeasured separately).

no $658.40 SJ502


669 Precast concrete inspection chamber size1200x700(internal)x1070mm deep to invert complete withreinforcement, granolithic concrete benching, channels,cast-in-situ concrete topping and excavation (structuralbeam supports, inspection chamber cover and framemeasured separately).

no $787.20 SJ504


671 Precast concrete encasement for 150mm diameter maindrainline including concrete haunching and jointing(excavation, drain pipe and structural supports measuredseparately).

m $137.10 SJ506

672 225mm thick (average) granolithic concrete (1:1:1) inbenching and haunching to bottom of inspectionchamber/sump finished to falls towards channels,including all necessary shaping of channels, bends etc asrequired.

m² $48.10 SJ051

673 100mm diameter half round vitrified clay straight or curvemain or branch channels to inspection chamber/sumpincluding bedding and jointing in cement mortar (1:1).

m $11.00 SJ054

674 150mm diameter ditto. m $13.80 SJ055

675 13mm thick cement and sand (1:2) rendering tointernal/external surfaces of inspection chamber/sump.

m² $11.90 SJ056

676 Light duty galvanised cast iron cover and frame size 600x 450mm for inspection chamber/sump including settingframe in cement mortar and sealing cover in grease andfine sand.

no $72.50 SJ057

677 Standard cast iron street gulley including connection, allnecessary excavation and concrete surround.

no $383.00 SJ046

of 100




678 Close-coupled dual flush low capacity coloured vitreouschina pedestal w.c. suite complete with w.c bowl, seatand cover and cistern with a flushing capacity of 4.5 litresper single action flush, including all necessary fittings andaccessories.

no $250.60 SJ257

679 Wash-hand basin in coloured vitreous china size 500 x400mm complete with waste plug and chain, approvednon-corrosive brackets, UPVC waste pipe, bottle trap andall necessary washers, seals and nuts and fixed to wallall as specified.

no $98.10 SJ105

680 Wash-hand basin with pedestal stand in colouredvitreous china size 500 x 400mm complete with wasteplug and chain, approved non- corrosive brackets, UPVCwaste pipe, bottle trap and all necessary washers, sealsand nuts and fixed to wall all as specified.

no $157.80 SJ501

681 Integral coloured cultured marble basin and top ofapproximate size 525 x 1500mm with 100mm backsplash,200mm front apron complete with integrated basin,approved single lever mixer tap with pop-up waste, bottletrap, waste pipe and galvanised steel brackets for fixingto wall and all necessary accessories for fixing andjointing to pipework.

no $681.00 SJ274

of 100




682 PUB approved stainless steel sensor operated flushvalve complete with stainless steel outlet flush pipes towater closets including fixing and jointing to water supplyand fittings as specified.

no $426.80 SJ286

683 PUB approved stainless steel sensor operated flushvalve complete with stainless steel outlet flush pipes tourinals including fixing and jointing to water supply andfittings as specified.

no $398.50 SJ285

684 15mm chromium plated brass pillar tap including allnecessary accessories for fixing and jointing topipeworks.

no $26.50 SJ106

685 15mm chromium plated brass pillar tap with swivel swanneck including all necessary accessories for fixing andjointing to pipeworks.

no $64.30 SJ107

686 Delay action tap including all necessary accessories forfixing and jointing to pipeworks.

no $164.40 SJ109

687 15mm chromium plated brass bib-tap including allnecessary accessories for fixing and jointing topipeworks.

no $24.80 SJ110

688 15mm chromium plated brass 2-way bib-tap including allnecessary accessories for fixing and jointing topipeworks.

no $33.80 SJ290

689 15mm chromium plated ceramic disc cartridge operatedsingle lever basin mixer tap complete with pop-up wasteincluding all necessary accessories for fixing and jointingto pipeworks.

no $64.50 SJ273

690 Chrome plated bath mixer tap with single lever controlcomplete with adjustable jet shower head, 1.5m flexibleshower hose and sliding bar and all necessaryaccessories as specified.

set $109.30 SJ361

of 100




Food-grade silicone thimble in natural colour with 4nos holes each 2.5mm diameter:

691 Size 18.5mm diameter x 2.5mm thick at basin tap inlet.

no $0.20 SJ350

692 Size 21.0mm diameter x 2.5mm thick for tap mixer. no $0.20 SJ351

693 15mm diameter constant flow regulator of 12 litres perminute for bib tap inlet at common areas.

no $5.50 SJ352

Stainless steel water supply pipe includingconnectors, elbows, bends, tees, reducers, etc andlaid in trench including excavation:

694 22mm diameter. m $20.00 SJ220

695 28mm diameter. m $23.40 SJ221

696 35mm diameter. m $28.80 SJ222

697 42mm diameter. m $34.20 SJ223

698 54mm diameter. m $57.90 SJ224

Stainless steel water supply pipe includingconnectors, elbows, bends, tees, reducers, etc. andfixed to roof top with concrete supports:

699 22mm diameter. m $13.20 SJ215

700 28mm diameter. m $16.50 SJ216

701 35mm diameter. m $21.20 SJ217

702 42mm diameter. m $26.60 SJ218

703 54mm diameter. m $50.30 SJ219

Stainless steel water supply pipes includingconnectors, elbows, bends, tees, reducers, etc. andfixed to wall with stainless steel clips/holderbats:

704 15mm diameter. m $13.10 SJ239

705 22mm diameter. m $17.00 SJ129

of 100




Stainless steel water supply pipes includingconnectors, elbows, bends, tees, reducers, etc. andfixed to wall with stainless steel clips/holderbats(cont'd):

706 28mm diameter. m $21.50 SJ130

707 35mm diameter. m $28.20 SJ131

708 42mm diameter. m $34.90 SJ132

709 54mm diameter. m $61.10 SJ225

Concealed copper pipes for cold/hot water supplycomplete with couplings, elbows, tees, etc fixed towalls, columns, beams including forming recesses,cutting grooves or chases in walls, columns etc andmaking good on completion as specified:

710 15mm diameter. m $18.50 SJ362

711 22mm diameter. m $24.10 SJ363

712 28mm diameter. m $28.50 SJ364

Compression fitting caps for copper pipes:




Ductile iron pipes with cement lining for water mainsincluding spigot and socket joints, laid in trenchincluding excavation:

716 80mm diameter and backfilling with selected earth. m $53.20 SJ136

717 80mm diameter and backfilling with approved granular material.

m $102.40 SJ369

718 100mm diameter and backfilling with selected earth. m $50.10 SJ137

719 100mm diameter and backfilling with approved granular material.

m $99.10 SJ370

of 100




Ductile iron pipes with cement lining for water mainsincluding flanged joints complete with bolts and nuts,laid on and including precast concrete supportblocks:

720 80mm diameter. m $58.10 SJ138

721 100mm diameter. m $53.40 SJ139

Ductile iron pipes with cement lining for water mainsincluding spigot and socket joints fixed to wall withholderbats:

722 80mm diameter. m $46.00 SJ140

723 100mm diameter. m $41.00 SJ145

Extra over 80mm diameter ductile iron cement linedpipes for water mains for fittings including flangedjoints complete with bolts and nuts:

724 Bends. no $75.00 SJ141

725 Tees. no $117.80 SJ142

726 Collars. no $88.40 SJ143

727 Socket adaptor. no $41.50 SJ144

Extra over 100mm diameter ductile iron cement linedpipes for water mains for fittings including flangedjoints complete with bolts and nuts:

728 Bends. no $82.60 SJ146

729 Tees. no $134.30 SJ147

730 Collars. no $101.90 SJ148

731 Duckfoot bend. no $41.20 SJ259

732 100mm diameter ductile iron flange adaptor fordistribution main complete with rubber gaskets, bolts andnuts all as specified.

no $123.60 SJ318

Cast iron sluice/gate valve with flanged ends:


734 100mm diameter. no $142.90 SJ152

of 100




735 100mm diameter x 65mm ductile iron flanged flow nozzle. no $117.50 SJ260

Bronze spring loaded lift check valve:



Cast iron spring loaded lift check valve with flangedends:


739 100mm diameter. no $423.10 SJ207

Brass high pressure equilibrium ball valve with brassarm and copper float:


741 100mm diameter. no $1,203.90 SJ154

Brass gate valve:



Brass ball stop valve:




747 15mm diameter isolating ball stop valve. no $7.20 SJ498

748 25mm diameter brass ball float valve. no $53.40 SJ262

749 35mm diameter brass globe valve. no $48.80 SJ213

750 40mm diameter solenoid valve for automatic time-controlled refuse chute flashing system.

no $282.00 SJ214

751 Labour only for boring holes in UPVC pipes forapproximately 3.2m long at 50mm centre/centre for useas bin chute sparge pipe.

no $10.90 SJ173

of 100




Brass high pressure screw down stop or bib cocks:







758 82mm diameter x 68mm high x 1.2mm thick purpose-made galvanised steel casing as locking device for publictap. (padlock measured separately).

no $7.80 SJ270

759 Rolled steel joists for support to tanks including bolts,fixing and painting.

kg $1.30 SJ181

760 63mm diameter Polyethylene gas pipe sleeved in 80mmdiameter UPVC pipe and laid in concrete channelincluding bituminous joints and filling up with cementmortar grout (concrete channel measured separately).

m $50.00 SJ491

761 63mm diameter Polyethylene gas pipe sleeved in 80mmdiameter UPVC pipe and laid in trench includingexcavation.

m $32.50 SJ495

762 63mm x 50mm diameter galvanised steel ElectrofusionTransition elbow to gas pipe.

no $46.90 SJ493

763 80mm diameter UPVC pipe sleeve for vertical gas pipefixed to wall.

m $13.90 SJ492

764 'Viking Johnson Junor' coupling for 50mm diametergalvanised steel gas pipe including locking ring, gasket,etc. and all necessary accessories.

no $44.00 SJ494

Heavy duty galvanised steel gas pipe includingsockets, connectors, elbows, tees, plugs, etc andfixed to wall or ceiling with collar brackets asspecified:

765 40mm diameter. m $18.10 SJ186

766 50mm diameter. m $21.30 SJ187

of 100




Full bore ball valve:








Copper gas pipe including connectors, elbows,bends, tees, etc and fixed to wall:

774 15mm diameter. m $16.30 SJ202

775 22mm diameter. m $22.10 SJ203

776 UPVC Casing/Trunking for water and gas servicesincluding trunking cover with splayed edges, overall size84 x 51mm as specified.

m $12.90 SJ228

Heavy duty galvanised steel pipe complying with APIStandard 5L Grade B Schedule 40 with welded jointsand fixed to wall or ceiling with pipe clips or mildsteel brackets:

777 40mm diameter. m $24.80 SJ272

778 50mm diameter. m $28.10 SJ269

Class "C" galvanised steel pipes fixed to duct wall asdry, wet or hosereel rising main including allnecessary brackets, connectors, welded flanges,bolts, nuts and gaskets, etc and testing theinstallation as specified:

779 50mm diameter. m $18.00 SJ357

780 100mm diameter. m $63.80 SJ242

781 150mm diameter. m $85.80 SJ243

of 100




Class "C" galvanised steel pipes fixed to duct wall asdry, wet or hosereel rising main including allnecessary brackets, connectors, welded flanges,bolts, nuts and gaskets, etc and testing theinstallation as specified (cont'd):

782 Extra over 50mm diameter pipe for bend or elbow. no $8.10 SJ496

783 Extra over 50mm diameter pipe for tee. no $9.00 SJ497

784 Extra over 100mm diameter pipe for bend. no $48.00 SJ244

785 Extra over 150mm diameter pipe for bend. no $90.20 SJ247

Rust proof electro galvanised steel box with glassfront for breeching inlet complete with locks andmaster keys as specified (breeching inlet measuredseparately) :

786 2-way. no $130.70 SJ250

787 4-way. no $147.50 SJ251

Breeching inlet complete with 1 no. 25mm diameterdrain valve including all necessary blank caps, chain,handwheel etc as specified:

788 100mm diameter 2-way. no $185.00 SJ253

789 150mm diameter 4-way. no $327.50 SJ254

790 Dry riser landing valve with instantaneous 63.5mmdiameter female coupling complete with gunmetal bodiesincluding anti-theft device consist of 3mm brass cap andear knob, and carbon steel pipe, etc as specified.

no $120.20 SJ252

791 25mm automatic air release valve as specified. no $26.20 SJ255

792 Approved canvas/nylon belt with key-alike padlocks forstrap locking handwheels in closed position.

no $4.80 SJ256

of 100




1.6mm thick electro-galvanised steel casing finishedin baked red epoxy resin complete with all necessaryaccessories as specified for:

793 Fire hose-reel. no $207.10 SJ292

794 2.5 kg fire extinguisher. no $78.40 SJ342

795 4.5 kg fire extinguisher. no $86.00 SJ359

796 Approved wall mounted double swivel and recessed typefire hose-reel complete with 30m long x 25mm diameterreinforced braided rubber hose, a jet or spray type shut-off nozzle, gun metal control valves, wall brackets andfittings including fixing to wall and painting.

no $347.40 SJ291

Dry powder portable fire extinguisher complete withhorn, wall brackets and embossing extinguisher with2 nos HDB logo as specified:

797 2.5 kg. no $55.90 SJ338

798 4.5 kg. no $72.20 SJ339

799 9 kg. no $88.70 SJ340

800 5kg CO2 portable fire extinguisher complete with horn,wall brackets and embossing extinguisher with 2 nos HDB logo as specified.

no $174.20 SJ341

of 100



GLAZING

Sheet/float glass in panes:

801 4mm thick ordinary quality clear sheet/float glass. m² $27.40 SK001

802 5mm thick ditto. m² $33.20 SK002


804 5mm thick obscured glass. m² $41.80 SK004

Tinted float glass in panes:

805 5mm thick. m² $45.90 SK005

806 6mm thick. m² $49.80 SK006

Clear tempered float glass in panes:

807 6mm thick. m² $77.80 SK012

808 8mm thick. m² $104.70 SK013

809 10mm thick. m² $125.50 SK014

810 12mm thick. m² $143.50 SK015

Tinted tempered float glass in panes:

811 6mm thick. m² $89.10 SK016

812 8mm thick. m² $119.40 SK017

813 10mm thick. m² $137.50 SK018

814 12mm thick. m² $156.60 SK019

Tinted laminated safety float glass in panes:

815 10.38mm thick. m² $110.50 SK020

816 12.76mm thick. m² $145.40 SK021

of 100



GLAZING (CONT'D)

Glass in louvres - varying from 100mm to 200mmwide:

817 5mm thick ordinary clear sheet/float glass. m² $33.20 SK008


819 5mm thick obscured wired glass. m² $42.70 SK010

820 6mm thick rough cast obscured wired glass. m² $49.50 SK011

of 100



PAINTING AND DECORATING

Concrete or Plastered Surfaces

821 One coat of approved acrylic emulsion paint (with 20%water dilution).

m² $1.80 SL002

822 One priming coat (with 20% water dilution) and two uppercoats (without water dilution) of approved acrylic syntheticemulsion paint.

m² $4.40 SL003

823 One priming coat (with 20% water dilution) and one uppercoat (without water dilution) of approved acrylic syntheticemulsion paint by spraying equipment, paint roller orother means including protecting door/window frames, orother surfaces from being tainted with paint.

m² $3.20 SL037

824 One coat of water based sealer and two subsequentcoats of approved water based Algae Resistant EmulsionPaint (all coats without dilution) Rate inclusive of theprovision of a 6 year warranty.

m² $6.20 SL041

825 One coat of water based sealer. m² $1.90 SL008

Metal Surfaces

826 One coat of approved lead and chromate-free primer. m2 $4.10 SL038

827 One coat of polyvinyl butyral etching primer. m2 $3.50 SL039

828 One undercoat and one finishing coat of approvedsynthetic enamel paint.

m² $5.90 SL009

829 One undercoat and one finishing coat of approvedsynthetic enamel paint on grilles or railing etc (rateinclusive of painting on both faces).

m² $7.00 SL010

830 Two coats of approved synthetic enamel paint to mildsteel sections or door frame not exceeding 300mm girth.

m $2.20 SL018

831 Surface treatment to structural steelwork with one coat ofzinc-rich epoxy primer and two coats of zinc phosphatepriming paint including blast cleaning at workshop.

m² $42.30 SL040

of 100



PAINTING AND DECORATING (CONT'D)

Pipe Surfaces

One coat of approved lead and chromate-free primer:

832 not exceeding 75mm diameter. m $1.00 SL012

833 exceeding 75mm but not exceeding 150mm diameter. m $2.00 SL013

834 exceeding 150mm but not exceeding 300mm diameter.

m $4.10 SL014

Two coats of approved lead and chromate-freeprimer:


One coat of polyvinyl butyral etching primer:




m $3.50 SL032

Two coats of approved synthetic enamel paint:




m $6.00 SL017

of 100



PAINTING AND DECORATING (CONT'D)

Timber Surfaces

842 One coat wood primer and two coats of approvedsynthetic enamel paint.

m² $9.80 SL019

843 Two coats of wood stain/wood dye and three coats ofclear varnish/lacquer in matt or gloss finish.

m² $14.40 SL036

844 Two coats of wood preservative. m² $3.30 SL020

845 Two coats of polyurethane varnish. m² $6.90 SL022

of 100



TURFING, TREE PLANTING & LANDSCAPING WORKS

846 225x225mm spot turfing (with 25mm thick original topsoil) at 450mm centre both directions with a layer ofapproved soil mixture 125mm thick including themaintenance of the turfing works during the "MaintenancePeriod" as specified.

m² $7.10 SM002

847 Strip turfing (with 25mm thick original top soil) 450mmwide and spaced 600mm between strips at an angle of 45degree on embankments with a layer of approved soilmixture 125mm thick including the maintenance of theturfing works during the "Maintenance Period" asspecified.

m² $10.60 SM004

Close turfing (with 25mm thick original top soil) witha layer of approved soil mixture 125mm thickincluding the maintenance of the turfing works duringthe "Maintenance Period" as specified:

848 To slope embankment. m² $13.10 SM009

849 To flat level surface. m² $12.20 SM011

850 Excavate trench to form shrub/flower bed, includingbackfilling to level about 250mm above the adjacentground level with approved soil mixture as specified(plants measured separately).

m³ $47.40 SM018

Excavate tree hole including backfill to a level 250mmabove ground with approved soil mixture as specified(tree measured separately):

851 1.50 x 1.50 x 1.00m deep. no $104.90 SM078

852 1.00 x 1.00 x 1.00m deep. no $46.60 SM077

853 0.50 x 0.50 x 0.50m deep. no $6.60 SM079

Planting of instant tree including maintenance asspecified (tree measured separately):

854 Not exceeding 300mm girth. no $4.20 SM080

855 Exceeding 300mm but not exceeding 500mm girth. no $5.50 SM081

of 100



TURFING, TREE PLANTING & LANDSCAPING WORKS (CONT'D)

Planting of tree saplings/fruit trees/palms includingmaintenance as specified (tree measured separately):

856 Large size with minimun height 2.00m. no $3.50 SM082

857 Medium size with minimun height 1.50m. no $2.80 SM083

858 Small size with minimun height 1.00m. no $2.10 SM084

859 Planting of shrubs of any size including maintenance asspecified (shrub measured separately).

no $1.10 SM085

Cut down trees with girth measured at a point 1.0mabove the ground, grub up roots and clear away fromsite:

860 Not exceeding 0.5m girth. no $208.30 SM066

861 Exceeding 0.5m but not exceeding 1.0m girth. no $256.50 SM067





866 Exceeding 3.0m but not exceeding 4.0m girth. no $1,040.90 SM072



869 Bintangore pole as supporting stake to tree including tiesas specified.

m $1.50 SM039

870 Tripod support with 3 nos. of bintangore poles includingties and gunny sack as specified.

no $13.10 SM040

871 Tree guard with 4 nos. bintangore poles 1.50m aboveground and tied together with galvanised wire bracing asspecified.

no $21.90 SM041

872 Tree guard with 4 nos. bintangore poles 0.30m aboveground and tied together with galvanised wire bracing asspecified.

no $8.80 SM042

of 100



TURFING, TREE PLANTING & LANDSCAPING WORKS (CONT'D)

Approved perforated UPVC sub-soil pipe with openend butt joints:

873 100mm diameter. m $8.90 SM014

874 150mm diameter. m $12.60 SM013

875 150mm diameter wrapped round with geotextile fabric (non-woven type).

m $14.10 SM076

876 19 to 25mm coarse aggregate wrapped round withordinary grade geotextile fabric (non-woven type) toperforated UPVC pipe including all necessary excavation(pipe measured separately).

m³ $72.00 SM065

877 50mm diameter UPVC pipe as weephole not exceeding300mm long.

no $2.40 SM075

878 Supply, fix and subsequent removal of temporarybarricade fencing consisting of 50 x 50 x 1650mm longbalau timber post spaced at 2400mm centre to centre,pointed at bottom and driven 450mm deep into theground and with 10mm diameter nylon ropes runninghorizontally and diagonally across the top and bottom ofbarricade including extra timber strutting at corner andend post as specified.

m $4.60 SM015

Approved green nylon netting:

879 Single layer. m² $1.40 SM043

880 Double layer. m² $2.90 SM044

of 100



MISCELLANEOUS

881 Design, erection and subsequent removal of protectivehoarding with overhead shelter average 4.5m high and1.70m wide with timber supports, metal sheet hoardingand timber floor boarding as shown in drawings.

m $430.30 SM064

882 Natural anodised aluminium extruded framed noticeboard, size 1200 x 900mm high, constructed of 2mm thickaluminium casing, complete with 1 no. aluminium framedoor infilled with 5mm thick clear polycarbonate sheet,hinges, lockset, 12.7mm thick softboard with velvet fabricfinish, 9mm thick plywood, complete with fluorescent tubeand wiring as specified.

no $420.30 SM034

883 200 x 50mm Electro-Galvanised Steel Trunking withremovable cover for telephone cables fixed to wall orceiling complete with slotted brackets and fixingaccessories as specified.

m $22.20 SM035

884 200 x 75mm Electro-Galvanised Steel Trunking withremovable cover for telephone cables fixed to wall orceiling complete with slotted brackets and fixingaccessories as specified.

m $23.30 SM036

885 155mm diameter Class `B' UPVC pipe for undergroundLT reticulation cables with concrete haunching andnecessary fabric reinforcement at pipe joints including theprovision of a nylon/polyethelane rope and testing of pipeon completion (Excavation and sand bed measuredseparately).

m $18.60 SM050

886 Extra over 155mm diameter UPVC pipe for Grade 20concrete haunching throughout including all necessaryformwork and A6 WSF reinforcement (Excavationmeasured separately).

m $7.50 SM051

887 UPVC plugs at pipe mouth of 155mm diameter UPVCpipe in draw pits.

no $8.10 SM058

888 110mm diameter UPVC lead-in pipe in trench includingend cap (Trench measured separately).

m $6.20 SM063

889 172.4mm wide (nominal) x 2mm thick high impact UPVCcable cover plates with embossed letterings as specified.

m $3.10 SM052

of 100



MISCELLANEOUS (CONT'D)

Drawpits for underground LT reticulation cablescomprising of 100mm thick `L' shaped pc slabs aswalls, 100mm thick concrete base reinforced with A6WSF reinforcement, the pit filled with sand bags andcovered with 450x450x75mm thick precast concretetop cover slabs with UPVC plates for various shapesand types as specified (measured flat on plan -excavation measured separately):

890 Rectangular shaped. m² $174.20 SM053

891 `T' shaped. m² $141.00 SM054

892 `Y' shaped. m² $143.00 SM055

893 `X' shaped. m² $137.60 SM056

894 `L' shaped. m² $143.30 SM057

895 `R' shaped. m² $152.50 SM062

896 Vertical drawpit marker comprising of 75mm diameterheavy duty UPVC conduit pipe with purpose madecapping cover as specified.

no $32.20 SM059

StarHub Telecommunication Cable Pipes and Manholes

110mm diameter UPVC pipes in trench includingexcavation and backfilling and completelysurrounding pipe with grade 20 concrete bed andhaunching and all necessary formwork :

897 1-way with concrete bed and haunching, 210mm wide x overall 210mm thick.

m $30.00 SJ371


m $46.00 SJ372


m $63.70 SJ373


m $68.20 SJ374


m $90.80 SJ375

of 100



MISCELLANEOUS (CONT'D)

StarHub Telecommunication Cable Pipes and Manholes (Cont'd)

110mm diameter UPVC pipes in trench includingexcavation and backfilling and completelysurrounding pipe with grade 20 concrete bed andhaunching and all necessary formwork (cont'd):


m $119.30 SJ376


m $150.30 SJ377

Reinforced concrete grade 30 manhole includingnecessary reinforcement and formwork with 20mmthick screeding trowelled smooth to fall at base, leanconcrete, excavation, hardcore and the installation ofchannel bracket and anchor iron (cover and framemeasured separately):

904 Type JX2 comprising of 120mm thick walls and bottom slab.

no $335.60 SJ378

905 Type MX1 comprising of 150mm thick walls and bottom slab.

no $1,238.50 SJ379


no $1,525.60 SJ380


no $2,977.30 SJ381


no $3,617.90 SJ382

909 78mm thick grade 30 concrete top slab overall sizeapproximately 1316 x 1202mm inclusive of the collectionof manhole frame and cover from StarHub's warehouseand setting frame in cement mortar and sealing cover ingrease and sand (manhole cover and frame supplied byStarHub).

no $62.70 SJ499

of 100



DAYWORK

Rates for the following items do not includeestablishment charges and profit:

910 Bricklayer. hr $11.90 SN001

911 Blocklayer. hr $11.90 SN002

912 Carpenter. hr $13.40 SN003

913 Concretor. hr $12.50 SN004

914 Construction Equipment Operator. hr $15.80 SN019

915 Crane Driver. hr $16.70 SN005

916 Drainlayer. hr $12.40 SN006

917 Excavator. hr $15.80 SN007

918 Fitter. hr $14.40 SN008

919 Glazier. hr $12.60 SN009

920 Ironmonger. hr $12.90 SN010

921 Joiner. hr $12.80 SN011

922 Labourer. hr $8.60 SN012

923 Lorry Driver. hr $12.50 SN013

924 Mason. hr $11.90 SN014

925 Mechanic. hr $14.90 SN015

926 Painter. hr $11.70 SN016

927 Pavior. hr $12.20 SN017

928 Piler. hr $13.50 SN018

929 Plasterer. hr $12.20 SN020

930 Plumber. hr $12.80 SN021

931 Roller Driver. hr $17.30 SN022

of 100



DAYWORK (CONT'D)

Rates for the following items do not includeestablishment charges and profit (Cont'd):

932 Roofer. hr $12.70 SN023

933 Scaffolder. hr $12.70 SN024

934 Steel Bender & Fixer. hr $12.60 SN025

935 Steel Worker. hr $14.10 SN026

936 Tiler. hr $12.20 SN027

937 Tractor Driver. hr $16.00 SN028

938 Watchman. hr $10.70 SN029

939 Welder. hr $11.40 SN030

940 Wireman. hr $14.80 SN031

941 Air compressor with air delivery capacity not less than 4.5 cu m per minute including pneumatic and sharpening tools and power supply (operator measured separately).

hr $24.70 SN032

942 Concrete mixer 200/140 litres including fuel. hr $15.60 SN033

943 Concrete mixer 300/200 litres including fuel. hr $22.90 SN034

944 Crane (KATO KR20H) including fuel and driver. hr $118.10 SN050

945 Diesel powered field welding machine with minimum 300 amp.

hr $15.40 SN036

946 Mechanical lawn mover with blade not exceeding 500mm and engine power not exceeding 150 cc.

hr $2.50 SN037

947 Motor crane including fuel and driver (3 tonne lifting capacity).

hr $42.40 SN038

948 Motor Crane including fuel and driver (8-13 tonne lifting capacity).

hr $75.70 SN051

949 Motor lorry 2.5 - 3 tonne size including fuel and driver. hr $30.10 SN039

of 100



DAYWORK (CONT'D)

Rates for the following items do not includeestablishment charges and profit (Cont'd):

950 Motor lorry 5.5 - 7 tonne size including fuel and driver. hr $48.60 SN040

951 Motor lorry 10 tonne size including fuel and driver. hr $57.90 SN052

952 Power driven pump 50mm size including fuel and driver.

hr $21.50 SN041

953 Power driven pump 75mm size including fuel and driver.

hr $27.30 SN042

954 Power loader on rubber-tyred wheels 1.20 cu m bucket capacity (flywheel horsepower 60 kw range) including fuel and driver.

hr $69.70 SN043

955 Road roller 6 tonne capacity including fuel and driver. hr $36.30 SN044

956 Road roller 8 to 10 tonne capacity including fuel and driver.

hr $42.10 SN045

957 Traxacavator 1.0 cu m capacity including fuel and driver.

hr $84.80 SN046


hr $91.40 SN047


hr $112.90 SN048

960 Wheel or crawler shovel or excavator loaders with back hoe bucket not exceeding 0.4 cu m or 1.3 cu m loader bucket capacity including fuel and driver.

hr $80.60 SN049

STANDARD SCHEDULE OF RATES FOR CIVIL ENGINEERING WORKS (JUL 2013)



FOR

CIVIL ENGINEERING WORKS (JUL 2013)

CONTENTS

S/No. DESCRIPTION PAGE

GENERAL PREAMBLES 1 - 3

PARTICULAR PREAMBLES TO VARIOUS TRADES 4 - 15

1. PILING 16 - 18a) Reinforced Concrete Piles b) Timber Pilesc) Steel Sheet Pilesd) Bakau Piles

2. EXCAVATION 19 - 24a) Excavationb) Extra over excavationc) Timberingd) Backfillinge) Hardcore and Blindingf) Disposal

3. CONCRETE WORK 24 - 27a) Concreteb) Reinforcementc) Formwork

4. BRICKWORKS 27 - 28a) Brickworkb) Rubble Walls

5. CARPENTRY AND JOINERY 28

6. STRUCTURAL STEELWORK AND METALWORK 28 - 31a) Steelworkb) Handrailing/Vehicular Impact Guard Railsc) Gratingsd) Raised Platforme) Bollards

7 WALL/FLOOR FINISHES 32

8 PAINTWORK 32 - 37a) Concrete and Plastered Surfacesb) Timber Surfacesc) Metal Surfacesd) Road Markings



FOR


CONTENTS


9 DRAINAGE WORKS 38 - 569.1 Sewersa) Blinding to Manhole baseb) Type A Section Granular Material c) Type B Section Concrete (Without Piling Base)d) Type B Section Concrete (With Piling Base)e) Type C Section Concrete (Without Piling Base) f) Type C Section Concrete (With Piling Base)g) Type D Section Concrete (Without piling Base)h) Type D Section Concrete (With Piling Base)i) Vitrified Clay Pipesj) UPVC Pipesk) RC Pipes Class 'H'l) RC Pipes Class 'M'm) Cast Iron Pipesn) Pipes in BackDrops/Tumbling Bayso) Concrete Rings and Surround to Manholep) Concrete Cover Slabs & PC Unit for Manholeq) Manhole Cover and Frame, Ladder, Railings, etcr) Other Works

9.2 Drainsa) Half Round and Composite Drain Channels and Block Drainsb) Drain Opening Cover slabs, Catch-Basin and Othersc) Sub-soil Pipes and Scupper Drainsd) Weepholese) Silt Traps, Water Trough & Vibration Access

10 ROADS AND PAVINGS 56 - 6210.1 Roadsa) Road Baseb) Bituminous Premix

10.2 Pavingsa) Concrete Paving Slabsb) BG Slabsc) Aeration Slabsd) Interlocking Concrete Paving Blockse) Expansion Jointsf) Kerbs, Dividers, etc.g) Pipe Crossings



FOR


CONTENTS


11 SIGNAGES 63 - 70a) Directional Signsb) Traffic Signsc) Signboards

12 GATES AND FENCING 71 - 72a) Gatesb) Chain Link Fencingc) Temporary Fencing

13 SITE CLEARANCE, TURFING AND TREE-PLANTING 72 - 75a) Site Clearanceb) Turfingc) Tree Planting

14 REPAIR WORKS SECTION 76 - 78a) Break-up and Replacementb) Pothole Repairc) Cuttingd) Refixing handrailingse) Erasing Roadline and Markings

15 DAYWORKS 79 - 82a) Labour (excluding profit and overheads)b) Construction Equipment (excluding profit and overheads)

Published by Housing and Development Board, Republic of Singapore.



GENERAL PREAMBLES

Page 1 of 82

Introduction 1 The clauses in the General Preambles shall apply to all work items contained in

the Standard Schedule of Rates. 2 The Particular Preambles to each Trade shall be read in conjunction with the

respective Trade in the Standard Schedule of Rates. 3 All rates contained in the Standard Schedule of Rates are exclusive of any

Goods and Services Tax. Any such Goods and Services Tax shall be borne by the HDB as and when the same becomes due and payable.

4 All rates include the allowances for complying with the General and Particular

Preambles. 5 All rates contained in the Standard Schedule of Rates are fixed basic rates (in

Singapore Currency) and no amendment whatsoever shall be made to such rates. The tenderers shall be deemed to have closely studied all rates contained herein and duly noted their implications.

6 Unless otherwise stated, the term "as specified" means as specified in any of the

documents forming part of the Contract. 7 Where brand/trade names are given in the descriptions, they are solely intended

for fixing the rates of the items. The products and materials to be used in the Contract shall be governed by the Specifications, Drawings and other documents forming the Contract (and not this Schedule of Rates).

Principles of Measurement

8 Unless otherwise stated, all work shall be measured nett as fixed in its place. 9 Unless otherwise stated, pipes are described by their internal diameters. 10 Where minimum deductions of voids are dealt with in this document they shall

refer only to openings or voids which are within the boundaries of measured area. Openings or voids which are at the boundaries of measured area shall always be the subject of deductions irrespective of size.

11 Where an item is indicated as “Add to last item for each additional………

depth/height/cross sectional area/hour”, the figure as indicated in the item shall be applied even though the difference for any depth/height/cross sectional area/hour is less than the figure indicated.

Description of Works and Inclusions

12 All work, materials and goods described in this Standard Schedule of Rates shall be of the respective kinds described in the Contract and in accordance with the instructions of the Superintending Officer or the Superintending Officer's Representative.

GENERAL PREAMBLES

Page 2 of 82

13 Headings to groups of items shall be read as part of the descriptions of the items to which the headings apply. 14 Unless specifically stated otherwise, the following shall be deemed to be included

in the description of the item of work:

a) Labour and all costs in connection therewith including the labour in fabricating, assembling, setting, fitting and fixing of materials and goods in position.

b) Materials and goods including materials required for lapping, jointing and

the like and all costs in connection therewith such as delivery, unloading, storing, returning of packings, handling, hoisting and lowering.

c) Preparing surfaces to receive work.

d) Protecting materials and work.

e) Waste of materials.


g) Use of construction equipment, tools, vehicles and all costs in connection

therewith.


i) General requirements set out in the Specifications, Drawings and other documents forming the Contract.

j) Establishment charges, overhead and profit.

Billing of Quantities

15 Where the unit of measurement is the linear metre, square metre and cubic metre, quantities shall be billed to the nearest whole unit. Fractions of the unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit.

16 Where the unit of measurement is the kilogramme, quantities shall be billed to

the nearest whole unit. Fractions of a unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit. Where the unit of billing is the tonne or litre, quantities shall be billed to the nearest two places of decimals.

17 Where the unit of measurement is the hour, fractions of the unit shall be billed to

the nearest next half hour. 18 Where the application of clauses 15 and 16 would cause an entire item to be eliminated, such item shall be billed to the nearest two places of decimals.

GENERAL PREAMBLES

Page 3 of 82

Application of Rates 19 Where rates with descriptions pertain to the same purpose are listed in more

than one Standard Schedule of Rates incorporated in the Contract; the rate as listed in the following schedules (in the stated order of precedence) shall prevail:

1st Precedence - Standard Schedule of Rates for Building Works

2nd Precedence - Standard Schedule of Rates for Civil Engineering

Works

3rd Precedence - Standard Schedule of Rates for Electrical Works

Units of Measurement 20 The following abbreviations are used for the units:

m - Linear metre m2 - Square metre m3 - Cubic metre no - Number p/tree - Per Tree job - Per Job kg - Kilogram ton - Tonne pr - Pair sht - Sheet ltr - Litre hr - Hour


Page 4 of 82

1.0 PILING WORK

Generally 1.1 Piling work shall be executed in accordance with the relevant Specifications and

the instructions of Superintending Officer's Representative.

Rates 1.2 The rate of each type of piling work shall be deemed to include removal of

underground obstructions together with all work in connection therewith unless specifically otherwise provided.

1.3 The rate of each type of piling work shall be deemed to include extending piles,

dollying and connections unless specifically otherwise provided. 1.4 Redriving or intermittent driving necessitated by upheaving or lengthening of

piles or by the removal of obstructions under piles or other causes including moving and repositioning the piling frame shall be deemed to be included with the items of piling.

1.5 The rate of each item of piling shall be deemed to include:

a) Handling, pitching, heading, pointing and bracing and providing protective wrought iron ring or helmet to pile.

b) Cutting off surplus and heads of piles and preparing and integrating

reinforcement into pile caps where applicable, extra excavation, backfilling and disposal of debris.

c) Disposing of materials displaced arising out of driving the piles.

1.6 The rate of each item of treated timber piles includes the application of wood

preservative to cut off surfaces of piles. 1.7 The rate of each item of reinforced concrete piles includes moulds,

reinforcement, preparing heads and extra labour and materials to receive pile extensions.

1.8 The rate of each item of pile tests includes provision of all anchors, platforms,

loading and unloading of materials, instruments and monitoring of the tests. 1.9 The rate for providing and assembling the equipment on the site and the

subsequent dismantling and removal shall be given separately as an item. 1.10 Movement of piling frames into position and about the site, any necessary

excavation or filling required to place the frames, raising or lowering the frames and any staging, barges or the like required to support the frames, shall be deemed to be included with the item of piling.


Page 5 of 82

Measurement 1.11 Payment for treated timber piles driven shall be the product of the relevant rate

per metre run and the penetration depth (measured from tip to cut-off level). 1.12 The pay length of each reinforced concrete pile after it is driven into the ground is

measured from the cut-off level of the pile to the end of pile shoe. Notwithstanding the provisions of Billing of Quantities contained in the General Preambles, the pay length of reinforced concrete piles shall be billed to the accuracy of nearest of 10mm.

2.0 EXCAVATION

Generally 2.1 Excavation of ordinary ground includes spoil or rubbish of every description,

rubbish tip material etc, sand gravel, decomposed granite, red or white earth, loamy or gravelly clay, gravelly laterite, mud, bog or any other formation by pick and shovel or machinery and at any depth.

Rates

2.2 The rate of each item of excavation shall be deemed to include excavating around foundation, piles and confined areas, getting out, removing of bakau piles, trimming, levelling and compacting bottoms of excavations and keeping sides plumb and planking and strutting (where stated).

2.3 Rates for each item shall be held to include for keeping all excavation free from

water and site dry, pumping or bailing and cable/services detection if required and providing any temporary drains required.

Measurement

2.4 The measurement of all excavations and subsequent disposal shall be those before excavating. The increase in bulk and any extra excavation required for earthwork support, planking and strutting and formwork for concrete shall be deemed to be included in the rates.

2.5 No allowance for working space shall be made in the measurement of all

excavation unless the method of construction requires workmen to operate from the outside of the structure. In such cases, a working space of 600mm shall be measured from the external face of the structure.

2.6 Filling shall be measured as equal to the void to be filled. Any thickness stated

shall be deemed to be after compacting.


Page 6 of 82

2.0 EXCAVATION (CONT’D)

Timbering

Rates 2.7 The rate for each item of the timbering for the sewer trenches/manholes shall be

deemed to include the design of the timbering by a Professional Engineer when the depth of the excavation/trenches exceeds 4.00 metres.

3.0 CONCRETE WORK

Generally 3.1 Unless otherwise stated, rates for concrete, reinforcement and formwork shall be

applicable to all work irrespective of locality, positions, shapes and height.

Rates 3.2 The rate for each item of concrete shall be held to include the following:

a) Forming, cutting grooves, chases, mortices, holes and making good any other sundry items of a like nature.

b) Extra labour for laying to falls, or cambers and preparing surfaces to

receive screeds or pavings also to be included.

c) All tests on concrete, cement and aggregate etc, as required and compliance with the strengths as specified.

d) Tamping and/or vibrating to give thorough compaction; working between

and around reinforcements.

e) Laying on any type of sub-base; preparing and leaving surfaces to receive screeds or paving.

Measurement

3.3 No deduction shall be made in the measurement of concrete work for:

a) Voids of 0.05 cubic metre or less.

b) Volume of the reinforcement and steelwork.

c) Openings in walls, floor, roof slabs and the like of 0.10 square metre or less.


Page 7 of 82

3.0 CONCRETE WORK (CONT'D) 3.4 Reinforcement

Rates 3.4.1 The rate of each item of reinforcement shall be deemed to include:

a) Allowances in the weight of reinforcement for rolling margins.

b) All cleaning and wire-brushing bars to remove rust, dust, mill scale, dirt, oil and other deleterious matters.

c) All bending, cutting and notching around obstructions.

d) All hooks and tying wires at all joints and crossings.

e) All non-designed spacers or chairs, distance blocks, temporary

fixings and supports. Measurement 3.4.2 The conversion factor for the various steel reinforcement bars shall be as

follows:

6mm diameter - 0.222 kg/m 7mm diameter - 0.302 kg/m 8mm diameter - 0.394 kg/m 9mm diameter - 0.499 kg/m 10mm diameter - 0.616 kg/m 13mm diameter - 1.042 kg/m 16mm diameter - 1.579 kg/m 20mm diameter - 2.466 kg/m 22mm diameter - 2.984 kg/m 25mm diameter - 3.854 kg/m 28mm diameter - 4.834 kg/m 32mm diameter - 6.313 kg/m

3.5 Fabric Reinforcement

Rates 3.5.1 The rate for each item of fabric reinforcement shall be held to include for

extra material at laps, tying wires and all bending, cutting and notching around obstruction.

Measurement

3.5.2 Only the nett area covered shall be measured and no deduction shall be made for opening less than 1.00 square metre.


Page 8 of 82

3.0 CONCRETE WORK (CONT'D) 3.6 Formwork

Rates 3.6.1 The rate of each item of formwork shall be deemed to include:

a) All necessary boardings, supports, erecting, framing, cutting, perforations for pipes, angles, cleaning, wetting and treatment with mould oil, mould liquid or limewhite and the like.

b) All splayed edges, notchings, allowance for overlaps and passings at angles, battens, strutting, bolting, wedging, easing, striking and removal.

Measurement 3.6.2 Formwork shall be measured to the surface of work sloping more than 15

degree from the horizontal. 3.6.3 No deduction shall be made in measurement of formwork for:

a) Openings less than 1 square metre.

b) Intersection of main and secondary beams.

c) Intersection of beams and stanchion casing or columns. 3.7 Precast Work

Rates 3.7.1 The rate of each item of precast work shall be deemed to include concrete,

reinforcement, formwork including the formation and filling of pockets, holes, chases and recesses for anchors, bolts and the like, grouting, pointing of joints, surface finishes, delivery, unloading, hoisting, erecting, fixing including all necessary temporary erection gear, bracing and working platforms.

4.0 BRICKWORK

Rates 4.1 The rate for each item of block, brickwork shall be held to include for all

special made blocks, bricks and in-situ concrete in lieu, all holdfasts and bonding ties at abutments to concrete structures, all rough and fair cuttings, oversailing and receding courses, rough relieving and discharging arches, wedging and pining, raking out joints for and pointing flashings, bedding plates, parging and coring flues, labour eaves filling, plumbing angles, forming square and rebated reveals, cut squints or birdsmouths, notches, forming, leaving or cutting chases, holes and mortices, cutting and pining and making good and any other sundry items of a like nature.


Page 9 of 82

4.0 BRICKWORK (CONT’D) Rates (Cont’d)

4.2 Rates for blockwork and brickwork shall be applicable to all work irrespective of positions, patterns, shapes and height.

Measurement

4.3 Deductions shall be measured the nett sizes of the openings and recesses, including the extra width or rebated reveals. No deductions shall be made for openings of 0.50 square metre or less.

4.4 Deductions shall be made for strings, sills, lintols and the like only when

exceeding 100mm in height. 5.0 CARPENTRY AND JOINERY

Description 5.1 The description of each item of carpentry work shall be deemed to include all

cutting, notching, boring, sinking, pelleting, fitting, trimming, mitring, halving, morticing, tenoning, dovetailing, scarfing, wedging and all ends, splayed edges, short lengths and temporary supports and any other sundry of a like nature and also all labour in forming, drilling for bolts and fixing in position complete with nails, screws or adhesives.

5.2 The description of each item of joinery work shall be deemed to include all

nailing, gluing, screwing, plugging, cutting, notching, holes, housing ends, mitring ends and shaped ends, angles, junctions, heading joints, short lengths, tongued angles, splayed or rounded edges, chamfers, rebates, grooves and any other sundry items of a like nature including stops and working cross-grain, fitting and hanging and the like.

6.0 STRUCTURAL STEELWORK AND METALWORK Description 6.1 The description of each item of work shall be deemed to include:-

a) Allowances for rolling margins and the weight of welding materials.

b) Shop and site fabrication including drilling, cutting (including holes and openings for other trades), notching, splicing, mitring, welding, riveting, bolting, machining ends and bearings, delivery, unloading, handling, assembling, hoisting, erecting, fitting and fixing in position, bedding, filling in solid, polishing and pointing including necessary lugs or other attachment.


Page 10 of 82

6.0 STRUCTURAL STEELWORK AND METALWORK (CONT’D) c) Provision of all necessary construction equipment, temporary

bracing supports and the like required for erection, providing samples and tests required by the specification, the inspection of welds including the use of any special radio-graphic techniques.

d) Protection such as wrapping finished work with paper, coating with

grease or carrying out such other protective measures as may be required and removing and cleaning on completion.

e) Nuts and any type of washer which may be required.

f) Preparation of shop Drawings.

Deduction 6.2 No deduction shall be made for drillings, holes, notchings, splay cuts and

the like. Measurement

6.3 Weights stated shall be net theoretical weights. 6.4 Steel sections and plates in connections or fitted stiffeners, column cap

and base plates, rigid frame bases and butt plates, purlins, girts, eaves, fascias and similar cleats or brackets attached to trusses, lattice girders and open web joists and plates, and similar items shall be weighted at net dimensions.

6.5 Irregular, including circular shaped plates shall be weighted at the

smallest size rectangles from which they can be cut; regular and triangular shaped plates shall be weighted at net dimensions.

6.6 Half or other parts of steel sections in connections shall be weighted at

half the weight of the section from which they have been cut when equal to or less than half the section and at the full weight of the section from which they have been cut when greater than half the section.


Page 11 of 82

7.0 WALL/FLOOR FINISHES

Rates 7.1 The rate for each item shall be deemed to include all temporary rules,

temporary grounds, temporary screeds and the like, cramps, dowels, ties, special metal supporting brackets and the like, cutting holes, notching and the like, masking, labour to internal angles other than coved angles, making good around pipes and the like, work in narrow widths and small quantities, joints between different types of work, joints between new and old work, internal angles, fair edges, rounded or chamfered edges or angles, quirks, grooves, V-joints, groin points and other intersections of curved surfaces, rounded coves and external angles not exceeding 25mm radius, necessary UPVC trimming pieces, mitres, stops and the like, and all making good and any other sundry items of a like nature.

7.2 Rate for each item shall also be deemed to include protecting surfaces from

the weather or building operations.

Measurement 7.3 No deduction shall be made for openings of 0.50 square metre or less. 7.4 In the measurement of plastering, no deduction shall be made for casings for

pipes under 300mm wide or angles which are finished in a different material if these do not exceed 100mm girth.

7.5 Work shall be deemed to be executed when scaffolding has been provided


7.6 Where an item is described as “Add to (or deduct from)……for each 5mm

thickness over (or under)…….”, the difference for any thickness less than 5mm shall be paid/deducted based on 5mm thick.

8.0 PAINTWORK

Rates 8.1 The rate for each item of painting shall be held to include for all necessary

preparation of surfaces including cleaning off, knotting, stopping and sandpapering woodwork, wire brushing metal and leaving all surfaces free from dust, rust, grease and oil before painting, narrow widths, etc.

Measurement

8.2 No deduction shall be made for openings of 0.50 m2 or less. 8.3 Work shall be deemed to be executed when scaffolding has been provided



Page 12 of 82

9.0 DRAINAGE WORK

Measurement 9.1 Unless otherwise described, excavation, backfill and disposal of excavated

material shall be measured separately. 9.2 Piling, hardcore, lean concrete, sand bed and concrete haunching to drains,

sewers and culverts shall be measured separately. 9.3 The measurement of lengths of pipes shall be along their centre lines and

lengths of pipes in backdrops, tumbling bays, etc., shall be measured separately.

9.4 The measurement of pipes in trenches shall include lengths occupied by fittings and valves.

9.5 Unless otherwise stated, pipes are described by their internal diameters.

Rates 9.6 The rate of each item of concrete haunching shall be deemed to include

moulds, formwork, reinforcement, forming holes, rebates, notchings, mortices and recesses.

9.7 The rate of each item of pipes shall be deemed to include the following:

a) Laying of pipes in trenches or open ground to required falls.

b) Labour and material for cutting and jointing pipework.

c) Accessories such as joints, sockets, connectors, elbows, etc.

10.0 ROADS AND PAVINGS

Measurement 10.1 The thickness of materials used for road pavement shall be measured nett,

i.e. consolidated thickness after compaction. 10.2 No deductions shall be made in measurement of areas for manhole covers

less than 1 square metre.

Rates 10.3 Unless otherwise stated, excavation, backfilling and the subsequent removal

of surplus excavated material shall be measured separately. 10.4 The rate of each item of base course shall be deemed to include the

supplying, depositing, spreading, levelling, compacting, ramming and consolidating to the finished thickness.


Page 13 of 82

10.0 ROADS AND PAVINGS (CONT’D) Rates (Cont’d)

10.5 The rate of each item of premix bituminous surfacing shall be deemed to include the following:-

a) Sweeping and brushing surface prior to applying tack coats or

asphalt surfacing.

b) Supplying and applying suitable tack coats wherever required.

c) Supplying and unloading of asphalt mixes as directed.

d) Supplying and laying by means of mechanical spreader/finisher,

rolling and finishing of asphalt mixes. e) Providing the necessary construction equipment, equipment, tools,

etc. and the subsequent removal upon completion. 10.6 The rate of each item of precast concrete kerbs, channels and drains shall

be deemed to include all necessary moulds, formwork, reinforcement and joints and cutting, all angles, intersections, ends, outlets, etc.

10.7 The rate for each item of precast concrete kerbs shall include for laying in

alignment and finishing fair on all exposed surfaces. 11.0 SIGNAGES

Measurement 11.1 The rate of each item of work for directional/traffic signs shall be deemed to

include foundations, supporting posts, excavation, preparation of surfaces, disposal of excavated material, upholding sides of excavation, backfilling, concrete, formwork, reinforcement and joints, etc.


Page 14 of 82

12.0 GATES AND FENCING

Measurement 12.1 The measurement for lengths of fences shall exclude lengths occupied by

gates.

Rates 12.2 The rate for each item for fences shall be deemed to include the following:

a) Excavation, preparation of surfaces, disposal of excavated materials, upholding sides of excavation, backfilling, concrete, formwork and reinforcement.

b) Posts, End Posts, Angle Posts, Intermediate Posts, Straining Posts

and Gate Posts.

c) Drilling and cranking top of posts.

d) Trowelling top of concrete bases to a weathered finish. 13.0 SITE CLEARANCE, TURFING AND TREE-PLANTING

Definition of Approved Soil Mixture 13.1 Approved soil mixture shall be three parts topsoil with one part of soil

conditioner and 1 kg per m3 of granular fertilizer NPK (15:15:6.4) or 4:2:1 subsoil, unwashed sand and soil conditioner with 1 kg per m3 of granular fertilizer NPK (15:15:6.4).

Measurement 13.2 The measurement of girths of the trees shall be at a height of 1.0 metre

above ground.

Rates 13.3 The rate for cutting down trees shall be deemed to include for grubbing up

roots and filling of voids after removal of tree roots. 13.4 The rate of each item of turfing and planting shall be deemed to include for

watering, weeding, fertilizing, cutting, settlement, re-seeding and maintenance during the “Maintenance Period” as specified.


Page 15 of 82

14.0 REPAIR WORKS SECTION

(a) Unless otherwise stated, the relevant particular preambles as hereinbefore described shall be applicable for the corresponding work items under this Section.

(b) Notwithstanding (a) above, for excavation works carried out under

Works Instructions, the rate for each item of excavation shall not include cable/services detection. The cable/services detection shall be paid separately by Works Instruction.

15.0 DAYWORKS

Rates 15.1 Rates shall be applicable in respect of all work executed on a daywork basis.

During the continuance of such work, the Contractor shall keep proper records of the names, occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and construction equipment employed. Such records, receipts or vouchers must be verified by the Superintending Officer or the Superintending Officer's Representative before payment can be effected.

of 82

HOUSING AND DEVELOPMENT BOARDSTANDARD SCHEDULE OF RATES FOR CIVIL ENGINEERING WORKS (JUL 2013)

S/N DESCRIPTION UNIT RATE ($) CODE

1. PILING

(a) Reinforced Concrete Piles

1.01 Providing and assembling of necessary piling equipmentto drive any size of reinforced concrete piles including allnecessary tools and appliances, subsequent dismantlingand removal on completion of the work on site.

item $4,585.60 Q042

Grade 40 precast reinforced concrete piles inclusiveof tools (providing, assembling and subsequentdismantling and removal of piling equipmentmeasured separately), materials and labour for theexecution thereof in any ground. Splices are to beapproved by the SO's Representative and paintedwith one coat of bitumen paint after welding. (The paylength is measured from the given cut off level of thepiles to the pointed end of the cast iron shoe orconcrete shoe):

1.02 150mm x 150mm (nominal working load of 20 tonne). m $23.90 SB305


1 04 200 200 ( i l ki l d f 40 t ) $35 60 SB0901.04 200mm x 200mm (nominal working load of 40 tonne). m $35.60 SB090




(b) Timber Piles

1.08 Providing and assembling of necessary piling equipmentto drive any size of treated timber piles including allnecessary tools and appliances, subsequent dismantlingand removal on completion of the work on site.

item $1,499.00 Q043

of 82



Tanalised timber vertical piles inclusive of tools(providing, assembling and subsequent dismantlingand removal of piling equipment measuredseparately), materials and labour for the executionthereof in any ground. The pay length to be measuredfrom the given cut-off level of the pile to the pointedend of the pile (price include mild steel box joint) forthe following sizes:

1.09 100mm x 100mm. m $10.70 Q004

1.10 125mm x 125mm (SWL 14T). m $16.50 Q005

1.11 150mm x 150mm (SWL 20T). m $22.90 Q006

1.12 175mm x 175mm (SWL 27T). m $34.10 Q007

(c) Steel Sheet Piles

1.13 Providing and assembling of necessary piling equipmentto drive/extract Grade 43 (BS 4360) steel sheet piles ofany size including all necessary tools and appliances,subsequent dismantling and removal on completion of thework on site.

item $8,159.30 SA032

1.14 Supply and delivery of Grade 43 (BS 4360) steel sheetpiles for use as temporary shoring to retain the sides of

ton $171.30 SA028piles for use as temporary shoring to retain the sides ofexcavation in approved section and lengths.

1.15 Driving Grade 43 (BS 4360) steel sheet piles includingthe provision of all labour, Construction equipment(providing, assembling and subsequent dismantling ofpiling equipment measured separately), tools andeverything necessary for the installation as specified.

ton $379.50 SA029

1.16 Extracting, recovering and stacking Grade 43 (BS 4360)steel sheet piles including the provision of all labour, tools(providing, assembling and subsequent dismantling ofpiling equipment measured separately), and everythingnecessary for the execution as specified.

ton $253.00 SA030

1.17 Grade 43 (BS 4360) steel sheet piles left in permanentlyincluding the provision of all labours, tools (providing,assembling and subsequent dismantling of pilingequipment measured separately), and everythingnecessary for the installation as specified.

ton $1,847.50 SA031

of 82



(d) Bakau Piles

1.18 Providing and assembling of necessary piling equipmentto drive any size of bakau piles including all necessarytools and appliances, subsequent dismantling andremoval on completion of the work on site.

item $980.40 Q045

Bakau piles minimum 80mm diameter at the largerend including cutting of piles (providing, assemblingand subsequent dismantling of piling equipmentmeasured separately):

1.19 Not exceeding 2.00m long. no $5.50 Q031

1.20 Exceeding 2.00m but not exceeding 4.00m long. no $9.30 Q032

1.21 Exceeding 4.00m but not exceeding 6.00m long complete with mild steel pipe sleeves.

no $18.10 Q033

1.22 Exceeding 6.00m but not exceeding 8.00m long ditto. no $23.10 Q034

Bakau piles minimum 80mm diameter at the largerend, by jacking method using excavator includingcutting of piles (rate inclusive of excavator):

1.23 Not exceeding 2.00m long. no $6.10 CE01001

1.24 Exceeding 2.00m but not exceeding 4.00m long. no $10.10 CE01002

1.25 Exceeding 4.00m but not exceeding 6.00m long complete with mild steel pipe sleeves.

no $19.10 CE01003

1.26 Exceeding 6.00m but not exceeding 8.00m long ditto. no $24.40 CE01004

1.27 Bakau piles minimum 80mm diameter at the larger end asroller supports.

m $1.80 Q030

(e) UPVC Pipes for Bored Piles

1.28 Approximately 16mm nominal internal diameter hollowUPVC pipe with a prelaid 3mm diameter wire inside theUPVC pipe within each cast in-situ pile.

m $2.00 CE01005

of 82



2. EXCAVATION

(a) Excavation

Excavation to formation level for roads, carparks,pavements, etc in ordinary ground including formingof surfaces and removing of surplus excavatedmaterials within site, for the following average overalldepth:

2.01 Not exceeding 150mm deep. m² $2.20 SA001

2.02 Exceeding 150mm but not exceeding 300mm deep. m² $3.80 SA002

2.03 Exceeding 300mm deep. m³ $11.60 SA003

2.04 Excavation only for the preparation of platform inordinary ground.

m³ $1.50 CE02003

2.05 Excavation for the preparation of platform in ordinaryground including filling and compaction to requiredplatform levels within site.

m³ $7.80 A094

2.06 Excavation in embankment commencing from reducelevel in ordinary ground including forming of surfaces andremoving of surplus excavated materials within site.

m³ $13.30 SA007

2 07 Excavate to form trial holes in ordinary ground not m³ $34 60 A0962.07 Excavate to form trial holes in ordinary ground notexceeding 2.00m deep and get out and return, fill in andram.

m $34.60 A096

2.08 Excavate to form trenches for drains, etc. in ordinaryground not exceeding 1.00m deep including formingbottom and get out, deposit on site, backfilling workingspace of trench with granular material/selected excavatedmaterial and cart away surplus excavated material fromsite.

m³ $19.70 A095

of 82



Excavate to form trenches for drains, etc. in ordinaryground including forming bottom and get out,deposit on site, planking and strutting, and backfillingworking space of trench with granularmaterial/selected excavated material and cart awaysurplus excavated material from site in stages of thefollowing depths:

2.09 Not exceeding 2.00m deep. m³ $27.30 A097

2.10 Exceeding 2.00m but not exceeding 4.00m deep. m³ $33.00 A098

2.11 Exceeding 4.00m but not exceeding 6.00m deep. m³ $36.90 A099

Excavate to form trenches for columns, pile caps,foundations, beams, basements, pier holes, etc. inordinary ground including forming of bottom,planking and strutting, part return, fill in and ram, andremainder get out and deposit on site as directed instages of the following depth:

2.12 Not exceeding 2.00m deep. m³ $26.30 SA008A

2.13 Exceeding 2.00m but not exceeding 4.00m deep. m³ $29.10 SA009A

2.14 Exceeding 4.00m but not exceeding 6.00m deep. m³ $33.60 SA010A

Excavate to form trenches for sewer lines manholesExcavate to form trenches for sewer lines, manholes,etc. in ordinary ground including forming bottom andget out, backfilling trench with granular material andcart away excavated material from site in stages ofthe following depths (timbering measuredseparately):

2.15 Not exceeding 2.00m deep. m³ $34.20 A100

2.16 Exceeding 2.00m deep but not exceeding 4.00m deep.

m³ $46.40 A101


m³ $48.00 A102


m³ $51.00 A103

2.19 Exceeding 8.00m deep. m³ $57.20 A104

of 82



Excavate to form trenches for service pipes, cablecrossings, etc. in ordinary ground including formingbottom and get out in stages of the following depths:

2.20 Not exceeding 2.00m deep and deposit on site. m³ $11.30 A105

2.21 Not exceeding 2.00m deep and cart away excavated material from site.

m³ $17.30 A106

2.22 Exceeding 2.00m deep but not exceeding 4.00m deep and deposit on site.

m³ $12.60 CE02001

2.23 Exceeding 2.00m deep but not exceeding 4.00m deep and cart away excavated material from site.

m³ $18.60 CE02002

(b) Extra over excavation

Extra over excavation for excavating/breaking upsurfaces to any depth using pneumatic tools etc:

2.24 Rock/reinforced concrete surfaces. m³ $71.90 A006

2.25 Metalled road surfaces. m³ $35.00 A007

2.26 Mass concrete surfaces. m³ $67.10 A008

(c) Timbering(c) Timbering

Open timbering for sewer trenches and manholesmeasured as supporting faces of excavations usingtype (I) timbering in stages of the following depths asshown in drawings (measured nett from drawings):

2.27 Not exceeding 2.00m deep. m² $11.30 A070

2.28 Exceeding 2.00m but not exceeding 4.00m deep. m² $11.40 A071


Open timbering for sewer trenches and manholesmeasured as supporting faces of excavations usingtype (II) timbering in stages of the following depths asshown in drawings (measured nett from drawings):


of 82



Open timbering for sewer trenches and manholesmeasured as supporting faces of excavations usingtype (II) timbering in stages of the following depths asshown in drawings (measured nett from drawings)(Cont'd):



Open timbering for sewer trenches and manholesmeasured as supporting faces of excavations usingtype (III) timbering in stages of the following depthsas shown in drawings (measured nett fromdrawings):




Close boarded timbering for sewer trenches andmanholes measured as supporting faces ofexcavations using type (IV) timbering in stages of thefollowing depths as shown in drawings (measurednett from drawings):






Close boarded timbering for sewer trenches andmanholes measured as supporting faces ofexcavations using type (V) timbering in stages of thefollowing depths as shown in drawings (measurednett from drawings):



of 82



Close boarded timbering for sewer trenches andmanholes measured as supporting faces ofexcavations using type (V) timbering in stages of thefollowing depths as shown in drawings (measurednett from drawings) Cont'd):




Close boarded timbering for sewer trenches andmanholes measured as supporting faces ofexcavations using type (VI) timbering in stages of thefollowing depths as shown in drawings (measurednett from drawings):






2.51 Extra over timbering for timber left in excavation asdirected including cutting runner below ground level all asrequired by the S.O.'s Rep. (Price to include for wedges,cleats, etc, measurements shall be taken from groundlevel to bottom of excavation. *Open/close timbering to bemeasured separately. This rate includes the omission ofthe extraction of timber left in).

m³ $272.80 A020

(d) Backfilling

Backfill excavated trench for service pipes, cablecrossings, etc including consolidation with:

2.52 Granular material. m³ $44.00 A107

2.53 Selected excavated material. m³ $9.70 A110

2.54 Imported earth. m³ $15.80 A109

of 82



(e) Hardcore and Blinding

Filling including consolidation as directed:

2.55 Hardcore. m³ $27.70 I005

2.56 Granite dust. m³ $61.60 A108

2.57 Granite chippings. m³ $60.70 I008

2.58 Unwashed sand bed. m³ $64.50 SA020

(f) Disposal

2.59 Cart away surplus excavated material from site of thework including transport and all charges.

m³ $11.90 SA016

3. CONCRETE WORK

(a) Concrete

3.01 Grade 15 concrete to underside of foundations, bases,slabs, etc.

m³ $146.30 I016

Concrete benching to base of drain finished to fallstowards precast inverts including trowelling all asspecified:

3.02 Grade 20. m³ $170.20 CE03029

3.03 Grade 25. m³ $172.60 CE03030

3.04 Grade 30. m³ $177.00 CE03011

Concrete in foundations, bases, walls, backdrops,tumbling bays, etc:

3.05 Grade 20. m³ $148.70 I017

3.06 Grade 25. m³ $151.00 I018

3.07 Grade 30. m³ $155.50 I019

3.08 Grade 35. m³ $157.90 I045

3.09 Grade 40. m³ $161.50 I044

of 82



(b) Reinforcement

Mild steel rod reinforcement including all bending,cutting and waste and fixing:

3.10 6mm diameter. kg $2.50 SB022


3.12 10mm diameter. kg $2.20 SB023A





Deformed high tensile steel rod reinforcementincluding all bending cutting and waste and fixing:

3.17 10mm diameter. kg $2.10 CE03016

3.18 13mm diameter. kg $2.10 CE03017

3.19 16mm diameter. kg $2.10 CE03018

3.20 20mm diameter. kg $1.80 CE03019

3.21 22mm diameter. kg $1.90 CE03020

3.22 25mm diameter. kg $1.80 CE03021

3.23 28mm diameter. kg $1.80 CE03022

3.24 32mm diameter. kg $1.80 CE03023

3.25 Extra over steel rod reinforcement for galvanising. kg $0.70 SB039

of 82



Welded steel fabric reinforcement well lapped andtied at joints (measured nett):

3.26 A5 m² $4.00 SB040A

3.27 A6 m² $5.00 SB041

3.28 A7 m² $6.50 SB042

3.29 A8 m² $8.00 SB043

3.30 A9 m² $9.80 CE03001

3.31 A10 m² $12.20 SB145A

3.32 B5 m² $6.90 SB146

3.33 B6 m² $8.00 SB147

3.34 B7 m² $9.00 SB148A

3.35 B8 m² $11.80 SB149A

3.36 B9 m² $13.90 SB229

3.37 B10 m² $15.80 SB150

3.38 B11 m² $18.30 CE03010$

3.39 B12 m² $20.80 SB151

3.40 B13 m² $26.10 CE03002

3.41 D5 m² $7.20 CE03006

3.42 D6 m² $9.30 SB048

3.43 D7 m² $12.00 SB049

3.44 D8 m² $15.40 SB124

3.45 D9 m² $19.20 SB230

3.46 D10 m² $23.80 SB231

3.47 D11 m² $28.50 CE03007

3.48 D12 m² $34.00 CE03008

3.49 D13 m² $39.90 CE03009

3.50 Galvanised finemesh (grid size 25mm x 25mm x 1.5mm thick).

m² $7.70 CE03028

of 82



Double wire welded steel fabric reinforcement welllapped and tied at joints (measured nett):

3.51 DA 10d/10. m² $28.40 CE03024

3.52 DA 13d/10. m² $43.50 CE03025

3.53 EA 10d/10. m² $21.50 CE03026

3.54 EA 13d/10. m² $31.80 CE03027

(c) Formwork

3.55 Shuttering to sides and soffits of concrete. m² $27.70 G005

4. BRICKWORKS

(a) Brickwork

Brickwork in standard common bricks (size 215mm x102.5mm x 65mm) laid in cement and sand mortar(1:3) with 10mm joints raked 10mm deep or flushpointed as work proceeds:

4.01 Mass brickwork generally. m³ $257.60 L005

4.02 One and half thick wall. m² $131.20 G011

4.03 One brick thick wall to chambers, access shaft, etc. m² $87.50 G010

4.04 One brick thick wall. m² $68.10 L006

4.05 Half brick thick wall reinforced with expanded metal brickwork reinforcement.

m² $36.00 L007

Common brickwall using M211 modular bricks size190x90x90mm laid in masonry cement and sand (1:3)mortar as specified with 10mm joints raked 10mmdeep or flush pointed as the work proceeds:

4.06 190mm thick. m² $63.90 SC015A

4.07 290mm thick. m² $87.10 SC044A

4.08 190mm wide Brick-on-edge red bull-nosed brick kerbusing 190x90x90mm thick red facing modular bricksjointed and pointed in cement and sand mortar (1:3) asspecified (screed measured separately).

m $22.20 SD054A

of 82



(b) Rubble Walls

4.09 Sledge granite set in cement and sand mortar (1:3) inabutments, retaining walls, to drains, rivers etc.

m³ $119.40 L001

4.10 Ditto but in walling, fair-faced and pointed in plain orcoloured cement.

m³ $133.70 L002

5. CARPENTRY AND JOINERY

Supply only approved well seasoned timber inconstructional members, scantlings, railings,deckings, etc cut to the forms and sizes required:

5.01 Kapoh or Balau (wrot timber). m³ $932.30 N015

5.02 Keruing (sawn timber). m³ $619.90 N016

5.03 Kempas (sawn timber). m³ $789.40 N017

5.04 Extra over timber for tanalising. m³ $202.40 N018

5.05 Extra over timber only for fixing. m³ $441.60 N019

6. STRUCTURAL STEELWORK AND METALWORK

(a) Steelwork

Mild steel flats, angles, tees, channels, hollowsections, square sections, rivets and bolts, etc. of anysize fabricated and fixed including welding or bolting,and painting with one coat of primer:

6.01 Grade 43A for structural steelwork only. kg $6.80 SH018A

6.02 For non-structural steelwork only. kg $5.60 SH019A

(b) Railings/Vehicular Impact Guard Rails

6.03 Aluminium alloy railing Type 'A' of 1000mm height with25mm diameter jail bars at 120mm centres and75x75mm barrier post at 1500mm centres embedded inand including concrete footing as shown in drawings.

m $284.60 CE07007

of 82



6.04 Aluminium alloy railing Type 'B' of 1000mm height with20mm diameter jail bars at 120mm centres and 54x54mmbarrier post at 1500mm centres embedded in andincluding concrete footing as shown in drawings.

m $215.10 CE07008

6.05 Aluminium alloy railing Type 'C' of 700mm height with20mm diameter jail bars at 300mm centres and 54x54mmbarrier post at 1500mm centres embedded in andincluding concrete footing as shown in drawings.

m $139.20 CE07009

6.06 Aluminium alloy railing Type 'D' of 1200mm height with20mm diameter jail bars at 120mm centres and 54x54mmbarrier post at 1500mm centres embedded in andincluding concrete footing as shown in drawings.

m $227.70 CE07010

6.07 Extra over aluminium alloy railing (all types) for fixing toconcrete structures complete with aluminium baseplate/case and stainless steel bolts as shown indrawings.

m $38.00 CE07011

6.08 40mm diameter nominal bore carbon steel standardsafety railing with 12mm square bars at 150mm centre tocentre including galvanising, Grade 20 concrete footingand painting as shown in drawings.

m $169.30 M046

6.09 Hot-dipped galvanised vehicular impact guard railcomplying with the requirements of AASHTODesignation:M 180 including 150mm x 110mm x 18mm x

m $90.10 M019

4.3mm thick galvanised 'C' channel posts spaced at 4.0metre centres to centres with concrete surround to detailsas shown in drawings.

6.10 Ditto but using 150mm x 150mm x 6mm SHS steel postsspaced at 2.0 metre centre to centre and to details asshown in drawings.

m $282.50 M020

(c) Gratings

6.11 3mm thick hot-dipped galvanised mild steel chequer plateincluding all necessary cutting and welding to mild steelworks.

m² $145.50 M040

of 82



6.12 Hot-dipped galvanised mild steel hinged grating overall41mm thick fabricated with 4.5mm x 25mm intermediateflats welded with 3mm thick galvanised mild steelCHEQUER PLATE on top resting on 2 nos. of 10mmdiameter cross bar and supported on 64mm x 45.5mm x4.5mm galvanised mild steel flat bend angle plateanchored to structure with fish tail as shown in drawings(for roadside and outlet drains).

m² $543.20 M027

6.13 Hot-dipped galvanised mild steel hinged grating overall47mm thick fabricated with 6mm x 32mm intermediateflats spaced at approximately 95mm centres with 3mmthick galvanised mild steel CHEQUER PLATE on top andresting on 5 nos. of 12mm diameter m.s. bar supportsand 75mm x 50mm x 7mm m.s. angle frame anchored tostructure with fishtails to details as shown in drawings(for 2m to 4m wide outlet drain).

m² $460.90 M045

6.14 Hot-dipped galvanised m.s. hinged vehicular gratingoverall 65mm thick fabricated with 12mm dia. m.s. barsspaced at 85mm centres, 9mm x 65mm m.s. flats at30mm centres and support on 75mm x 75mm x 9mm m.s.angle frame anchored to structure with fishtails to detailsas shown in drawings.

m² $1,291.90 M030

6.15 Ditto but with 12mm dia m.s. bars spaced at 120mmcentres and 9mm x 65mm m.s. flats at 35mm centres andto details as shown in drawings.

m² $1,083.60 M031

6.16 3-piece hot-dipped galvanised mild steel hinged vehiculargrating overall 32mm thick fabricated with 9mm x 32mmthick intermediate m.s. flats with 10mm diameter m.s. barsupports on 64mm x 38mm x 4.5mm thick m.s. angleframe to details as shown in drawings (forcarparks/service roads).

m² $695.60 M032

6.17 3-piece hot-dipped galvanised mild steel hinged vehiculargrating overall 35mm thick fabricated with 9mm x 32mmthick intermediate m.s. flats and 3mm thick CHEQUEREDPLATE welded to top of centre piece and 10mm diameterm.s. bar supports and 64mm x 38mm x 4.5mm thick m.s.angle frame to details as shown in drawings (forcarparks/service roads).

m² $736.50 M050

of 82



6.18 2-piece hot-dipped galvanised mild steel hinged vehiculargrating overall 32mm thick fabricated with 9mm x 32mmthick intermediate m.s. flats with 10mm diameter m.s. barsupports on 38mm x 38mm x 6mm thick m.s. angle frameto details as shown in drawings (for service roads).

m² $663.10 CE07005

6.19 Mild steel grating to manhole of storm water pipe conduitoverall size 836mm x 676mm fabricated with 26mm x6mm thick and 32mm x 6mm thick flats with 2nos 13mmdiameter mild steel rods all welded together and 38mm x38mm x 6mm thick angle frame with lugs cast intoconcrete to details as shown in drawings.

no $215.80 CE07001

(d) Raised Platform

6.20 Raised steel platform wash-bay, overall size 9000mm x3500mm wide consisting of rolled steel joists supports asframing to receive used sheet pile sections all weldedtogether to details as shown in drawings (concretepavement and water pump measured separately).

no $1,472.70 CE07002

(e) Bollards

6.21 90mm diameter x 3.2mm thick hollow section hot-dippedgalvanised mild steel detachable pipe bollard, 900mmhigh above ground with concrete footing and secure to

no $148.10 CE07006

high above ground with concrete footing and secure tom.s. fish-tail attached to the footing with a padlockincluding necessary painting and excavation as shownin drawings.

6.22 100mm diameter mild steel detachable pipe bollard900mm high above ground with footing includingnecessary painting and excavation as shown indrawings.

no $67.80 M039

6.23 230mm diameter R.C. bollard 1050mm high aboveground with footing and m.s. reinforcements includingnecessary excavation as shown in drawings.

no $70.90 M023

6.24 150mm diameter x 150mm high precast concrete bollardwith 1no of T20mm diameter (200mm long) steel barincluding bedding in cement mortar 1:3 and paintingsurfaces with two coats of approved yellow fluorescentpaint.

no $13.10 CE11025

6.25 6mm diameter galvanised electrically welded steel linkchains polished and self coloured.

m $3.90 M024

6.26 Supply of 60mm Yale padlock complete with keys orother approved equivalent.

no $25.00 M052

of 82



7. WALL/FLOOR FINISHES

7.01 One coat of approved 'Protective Coating' to inner wallsurface of box culvert.

m² $5.60 CE08001

7.02 Extra over concrete slab for trowelling floor surface. m² $1.60 SD002A

7.03 20mm thick cement and sand (1:3) rendering to brickworkor concrete trowelled smooth with steel trowel.

m² $17.60 L008

7.04 ADD to (or deduct from) LAST ITEM for each 5mmthickness over (or under) 20mm.

m² $1.60 L009

7.05 20mm thick cement and sand (1:2) rendering to invertsand benchings. (Measured on plan).

m² $12.30 G014

7.06 ADD to (or deduct from) LAST ITEM for each 5mmthickness over (or under) 20mm (Measured on plan).

m² $2.00 G065

7.07 20mm thick granolithic paving consisting of cement, sandand granite chippings (1:1:2) to floor and trowelled to asmooth finish.

m² $12.20 SD019A

7.08 ADD to (or deduct from) LAST ITEM for each 5mmthickness over (or under) 20mm.

m² $2.50 SD020A

8. PAINTWORK

(a) Concrete and Plastered Surfaces

8.01 One coat of approved synthetic gloss enamel paint tokerbs, dividers, bollards.

m² $7.90 O065

8.02 One coat of primer sealer and one coat of approvedsynthetic gloss enamel paint to kerbs, dividers andconcrete bollards.

m² $8.50 CE09020

8.03 One coat of approved emulsion paint to concretesurfaces, parapet walls, etc.

m² $1.60 O066

(b) Timber Surfaces

8.04 Two coats of approved wood preservative on wood work. m² $3.50 N025

8.05 Stop, knot with spirit knotting varnish, prime with one coatwood primer and paint two coats of approved syntheticenamel paint on woodwork.

m² $9.80 N026

of 82



(c) Metal Surfaces

8.06 Brush with steel wire brush to remove all rust, prepareand apply one coat of lead and chromate free primer orzinc chromate primer and two coats of approved syntheticenamel paint on steel and iron-work (girth measurement).

m² $8.00 N022

8.07 Brush with steel wire brush to remove all rust, prepareand apply one coat of lead and chromate free primer orzinc chromate primer and two coats aluminium paint onsteel and iron-work (girth measurement).

m² $7.30 N023

8.08 Brush with steel wire brush to remove all rust, prepareand apply one coat of lead and chromate free primer orzinc chromate primer and two coats red lead oxide painton steel and iron-work, one coat before and the otherafter erection (girth measurement).

m² $7.20 N024

(d) Road Markings

White thermoplastic paint 1.5mm thick forlongitudinal road markings to the following widthsand spacings as shown in drawings or as directedincluding cleaning and preparation of road surface,setting out and aligning road markings, apply primercoat at the rate of 220 gm per m² apply drop onballotini glass beads at the rate of 300 ± 50 gm/m² forsurface reflectorization, and everything else asdescribed in the Specifications and other relateddocuments of the Contract:

8.09 100mm wide lines. m $2.00 O014

8.10 150mm wide lines. m $2.80 O016

8.11 200mm wide lines. m $4.10 O017

8.12 300mm wide lines. m $4.70 O018

8.13 Other road markings exceeding 300mm wide. m² $15.60 O019

of 82



Yellow thermoplastic paint 1.5mm thick forlongitudinal road markings to the following widthsand spacings as shown in drawings or as directedincluding cleaning and preparation of road surface,setting out and aligning road markings, apply primercoat at the rate of 220 gm per m² apply drop onballotini glass beads at the rate of 300 ± 50 gm/m² forsurface reflectorization, and everything else asdescribed in the Specifications and other relateddocuments of the Contract:

8.14 100mm wide lines. m $2.00 O020

8.15 150mm wide lines. m $2.90 O021

8.16 100mm wide zig-zag lines (measured straight along the edge of road/kerb).

m $2.70 CE09008

8.17 200mm wide lines. m $4.30 O022

8.18 300mm wide lines. m $5.60 O023

8.19 455mm wide lines. m $7.70 O024

Thermoplastic paint 2mm thick for road markings tothe following widths and spacings as shown indrawings or as directed including cleaning andpreparation of road surface setting out and aligningpreparation of road surface, setting out and aligningroad markings, apply primer coat at the rate of 220gm per m² apply drop on ballotini glass beads at therate of 300 ± 50 gm/m² for surface reflectorization,and everything else as described in theSpecifications and other related documents of theContract:

8.20 1800mm wide road hump with 150mm wide transverse yellow lines spaced at 200mm apart.

m $20.10 CE09002

8.21 4000mm wide road hump with ditto. m $29.60 CE09003

of 82



White thermoplastic paint 3mm thick for longitudinalroad markings to the following widths and spacingsas shown in drawings or as directed includingcleaning and preparation of road surface, setting outand aligning road markings, apply primer coat at therate of 220 gm per m² apply drop on ballotini glassbeads at the rate of 300 ± 50 gm/m² for surfacereflectorization, and everything else as described inthe Specifications and other related documents of theContract:

8.22 200mm wide lines. m $4.50 O025

8.23 300mm wide lines. m $6.40 O026

8.24 Single traffic arrows. no $42.30 O027

8.25 Double traffic arrows. no $52.80 O028

8.26 Triple traffic arrows. no $64.20 O029

8.27 Merging traffic arrows. no $58.50 CE09007

8.28 Standard letterings/markings 2520mm height. no $37.40 CE09012


8 30 Standard alphanumeric characters 180mm height no $15 90 CE090168.30 Standard alphanumeric characters 180mm height. no $15.90 CE09016

8.31 Pedestrian crossing and other road marking exceeding 300mm wide.

m² $21.50 O032

of 82



Yellow thermoplastic paint 3mm thick for longitudinalroad markings to the following widths and spacingsas shown in drawings or as directed includingcleaning and preparation of road surface, setting outand aligning road markings, apply primer coat at therate of 220 gm per m² apply drop on ballotini glassbeads at the rate of 300 ± 50 gm/m² for surfacereflectorization, and everything else as described inthe Specifications and other related documents of theContract:

8.32 200mm wide lines. m $4.80 O033

8.33 300mm wide lines. m $7.10 O034

8.34 455mm wide lines. m $10.80 O035

8.35 Single traffic arrows. no $40.30 CE09004

8.36 Double traffic arrows. no $56.90 CE09005

8.37 Triple traffic arrows. no $69.60 CE09006



8 40 Standard letterings/markings 310mm height no $18 40 CE090158.40 Standard letterings/markings 310mm height. no $18.40 CE09015

8.41 Standard alphanumeric characters 180mm height. no $15.90 CE09017

8.42 Road markings exceeding 455mm wide. m² $23.00 O038

8.43 White thermoplastic paint 8mm thick x 300mm wide forforming regulating strips as shown in drawings or asdirected on site including cleaning and preparation ofroad surface, setting out and aligning road markings,apply primer coat at the rate of 220gm per m² apply dropon ballotini glass beads at the rate of 300 ± 50 gm/m² forsurface reflectorization, and everything else as describedin the Specifications and other related documents of theContract.

m $19.80 CE09001

of 82



One coat of white colour quick drying chlorinatedrubber based approved road line paint withmechanical means on:

8.44 Pedestrian or zebra crossings and other road markings exceeding 300mm wide.

m² $14.50 O054

8.45 100mm wide lines. m $1.50 O055

8.46 150mm wide lines. m $2.20 O056

8.47 200mm wide lines. m $2.90 O057

8.48 300mm wide lines. m $4.40 O058

8.49 Single traffic arrows. no $14.70 CE09023

8.50 Double traffic arrows. no $20.30 CE09024

8.51 Triple traffic arrows. no $26.60 CE09025





8.56 Standard alphanumeric characters 180mm height. no $3.40 CE09011

8.57 One coat of white colour road marking quick dryingchlorinated rubber based paint for handicap logo with theword 'RESERVED' painted in red on concrete pavedparking lot.

no $32.70 O070

8.58 Extra over items O054 to O061, CE09009, CE09019,CE09010 and CE09011 for using yellow, red or blackcolour quick drying chlorinated rubber based paint.

per centum

8.80% O080

of 82



9. DRAINAGE WORKS

9.1 SEWERS

(a) Blinding to Manhole Base

9.01 75mm thick unwashed sand bed/granite dust or fines assealing coat to bottom of manhole base as shown indrawings.

m² $4.30 A048

9.02 75mm thick Grade 15 concrete blinding to bottom ofmanhole base including necessary formwork as shown indrawings.

m² $11.00 A068

(b) Type "A" Section Granular Material

Type "A" section approved granular material bed tosewer line as per details shown in drawings:

9.03 225mm diameter sewer line. m $5.40 B002




9 07 525mm diameter sewer line m $9 50 B0069.07 525mm diameter sewer line. m $9.50 B006







9.14 1.050m diameter sewer line. m $26.40 B013





of 82



Type "A" section approved granular material bed tosewer line as per details shown in drawings (Cont'd):



(c) Type "B" Section Concrete (Without Piling Base)

Grade 30 concrete bed and haunching of Type "B"section to sewer line complete with 75mm thickGrade 15 concrete blinding and all necessaryformwork as per details shown in drawings :

9.21 225mm diameter sewer line. m $38.00 C002











9.32 1.050m diameter sewer line. m $147.30 C013







of 82



(d) Type "B" Section Concrete (With Piling Base)

Grade 30 concrete bed and haunching of Type "B"section to sewer line complete with 75mm thickunwashed sand bed including steel/fabricreinforcement and all necessary formwork as perdetails shown in drawings where piling is required(Piling measured separately):










9 48 900mm diameter sewer line m $156 40 C0309.48 900mm diameter sewer line. m $156.40 C030









of 82



(e) Type "C" Section Concrete (Without Piling Base)

Grade 30 concrete bed and haunching of Type "C"section to sewer line complete with 75mm thickGrade 15 concrete blinding and all necessaryformwork as per details shown in drawings :

9.57 225mm diameter sewer line. m $47.30 D002











9.68 1.050m diameter sewer line. m $206.10 D013







of 82



(f) Type "C" Section Concrete (With Piling Base)

Grade 30 concrete bed and haunching of Type "C"section to sewer line complete with 75mm thickunwashed sand bed including steel/fabricreinforcement and all necessary formwork as perdetails shown in drawings where piling is required(Piling measured separately):



















of 82



(g) Type "D' Section Concrete (Without Piling Base)

Grade 30 concrete bed and haunching of Type "D"section to sewer line complete with 75mm thickGrade 15 concrete blinding and all necessaryformwork as per details shown in drawings :

9.93 225mm diameter sewer line. m $69.60 E002








9.101 825mm diamater sewer line. m $197.50 E010



9.104 1.050m diameter sewer line. m $296.00 E013







of 82



(h) Type "D" Section Concrete (With Piling Base)

Grade 30 concrete bed and haunching of Type "D"section to sewer line complete with 75mm thickunwashed sand bed including steel/fabricreinforcement and all necessary formwork as perdetails shown in drawings where piling is required(Piling measured separately):










9 120 900mm diameter sewer line m $263 40 E0309.120 900mm diameter sewer line. m $263.40 E030









of 82



(i) Vitrified Clay Pipes

Vitrified clay pipes with flexible joints includingrubber rings etc all as per Specifications:

9.129 200mm diameter. m $55.50 CE10032

9.130 225mm diameter. m $61.20 F002

9.131 300mm diameter. m $103.80 F003

(j) UPVC Pipes

UPVC pipes to SS272 with flexible joints includingrubber ring etc all as per Specifications:

9.132 250mm diameter. m $41.60 CE10028

(k) RC Pipes Class `H'

R.C. pipes Class `H' in ordinary portland cement withspigot and socket and rubber ring joints:

9.133 300mm diameter. m $121.90 F005

9.134 375mm diameter. m $149.30 F007

9.135 450mm diameter. m $179.80 F009

9.136 525mm diameter. m $206.00 F011

9.137 600mm diameter. m $257.10 F013

9.138 675mm diameter. m $295.00 F015

9.139 750mm diameter. m $348.30 F017

9.140 825mm diameter. m $372.60 F019

R.C. pipes Class `H' lined with PVC or HDPE blanket(spigot and socket or butt ended pipes with loosecollars):

9.141 900mm diameter. m $467.20 F021

9.142 975mm diameter. m $523.60 F023

9.143 1.050m diameter. m $556.60 F025

9.144 1.125m diameter. m $591.70 F027

of 82



R.C. pipes Class `H' lined with PVC or HDPE blanket(spigot and socket or butt ended pipes with loosecollars) (Cont'd):

9.145 1.200m diameter. m $599.20 F029

9.146 1.350m diameter. m $730.20 F031

9.147 1.500m diameter. m $837.50 F033

9.148 1.725m diameter. m $1,025.00 F035

9.149 1.800m diameter. m $1,133.20 F037

(l) Reinforced Concrete Pipes Class `M'

R.C. pipes Class `M' in ordinary portland cement withspigot and socket and with rubber ring joints:

9.150 375mm diameter. m $136.70 F006

9.151 450mm diameter. m $154.50 F008

9.152 525mm diameter. m $177.40 F010

9.153 600mm diameter. m $229.20 F012

9 154 675mm diameter m $258 50 F0149.154 675mm diameter. m $258.50 F014

9.155 750mm diameter. m $295.50 F016

9.156 825mm diameter. m $324.40 F018

(m) Cast Iron Pipes

Heavy duty cast iron pipe with flexible joint asspecified:

9.157 225mm diameter. m $91.90 G047

9.158 300mm diameter. m $107.50 G048

9.159 100mm diameter cast iron spigot and socket vent pipefixed complete including all fittings, etc as specified.

m $44.10 G049

of 82



(n) Pipes in BackDrops/Tumbling Bays

Vitrified clay pipes or concrete pipes in backdrops,tumbling bays, raised junction connections, etcincluding cutting to required lengths:

9.160 200mm diameter. m $42.80 CE10033

9.161 225mm diameter. m $72.30 F042

9.162 300mm diameter. m $120.30 F045

Extra over 200mm diameter vitrified clay pipes orconcrete pipes for:

9.163 Bend. no $181.20 CE10034

9.164 Junction. no $311.70 CE10035

Extra over 225mm diameter vitrified clay pipes orconcrete pipes for:

9.165 Bend. no $65.80 F043

9.166 Junction. no $194.40 F044

Extra over 300mm diameter vitrified clay pipes orExtra over 300mm diameter vitrified clay pipes orconcrete pipes for:

9.167 Bend. no $58.90 F046

9.168 Junction. no $272.70 F047

(o) Concrete Rings and Surround to Manhole

Precast reinforced concrete wall in tubes as manholechamber including supply and lay 150mm thick Grade30 concrete surround and necessary formwork asshown in drawings :

9.169 1.050m diameter. m $703.10 G054

9.170 1.200m diameter. m $828.50 G055

of 82



Precast reinforced concrete wall in tubes as manholechamber including supply and lay 150mm thick Grade30 concrete surround and necessary formwork asshown in drawings (Cont'd):

9.171 1.350m diameter. m $923.90 G056

9.172 1.500m diameter. m $1,051.30 G057

9.173 1.800m diameter. m $1,380.90 G058

(p) Concrete Cover Slabs & PC Unit for Manhole

Precast or cast-in-situ concrete cover slab, undersideto be PVC lined, to brick/cast-in-situ concrete accessshaft all as shown in drawings :

9.174 150mm thick to access shaft with 600mm x 600mm square opening.

no $375.80 G026

9.175 225mm thick to access shaft with 750mm x 750mm square opening.

no $475.80 G027

200mm thick precast concrete slab to tube chamber,underside to be PVC lined, including concretesurround and formwork all as shown in drawings :

9.176 1.050m diameter. no $631.40 G028

9.177 1.200m diameter. no $888.50 G029

9.178 1.350m diameter. no $1,152.30 G030

9.179 1.500m diameter. no $1,357.20 G031

9.180 1.800m diameter. no $1,782.00 G032

200mm thick precast concrete intermediate slab totube chamber, underside to be PVC lined, includingconcrete surround and formwork all as shown indrawings :

9.181 1.500 m diameter. no $1,514.80 G033

9.182 1.800m diameter. no $1,782.00 G034

of 82



Precast reinforced concrete unit for manhole, overallsize 800 x 800 comprising of 100mm thick wallincluding bedding in cement mortar (1:3) and Grade30 concrete surround to details as shown in drawings:

9.183 100mm high. no $63.90 CE10020

9.184 200mm high. no $83.60 CE10021

(q) Manhole Cover and Frame, Ladder, Railings, etc.

Double triangular manhole cover and frame includingbedding frame in cement and sand mortar (1:3) andGrade 30 concrete surround to details as shown indrawings :

9.185 Overall dimensions 800mm x 800mm x 140mm heavy duty cover.

no $178.00 G035

9.186 Overall dimensions 750mm x 750mm x 90mm medium duty cover.

no $94.60 G036

9.187 Aluminium ladder 450mm wide including stringers, rungsto details as shown in drawings.

m $63.50 G038

9.188 Aluminium ladder holder bracket and shoe to details as set $56.80 G039shown in drawings (For 1 no. of ladder).

9.189 44mm (external) diameter x 1000mm high aluminiumalloy handrailing including screwed bends, junctions,flanged bottom to details as shown in drawings.

m $87.10 G040

9.190 Aluminium alloy safety link chain including hooks and endrings to details as shown in drawings.

no $23.60 G041

Stainless steel safety chain including stainless steelplate, hook and eye and shackle to details as shownin drawings for:

9.191 750mm to 825mm diameter sewer. set $141.30 G042

9.192 900mm to 1050mm diameter sewer. set $153.40 G043

9.193 1200mm diameter sewer and above. set $165.50 G044

of 82



16mm diameter multi-strand poly-propylene nylonrope as safety chain including stainless steel plate,hook and eye and shackle to details as shown indrawings for:

9.194 750mm to 825mm diameter sewer. set $26.40 CE10005

9.195 900mm to 1050mm diameter sewer. set $26.80 CE10006

9.196 1200mm diameter sewer and above. set $27.10 CE10007

9.197 Malleable cast iron step all in accordance with BS 1247. kg $21.40 G045

9.198 Ductile cast iron manhole cover and frame overalldimensions 850mm x 850mm x 100mm including beddingframe as shown in drawings.

no $229.50 M036

9.199 Supply of 6mm diameter `T-shape' galvanised mild steellifting key (for opening of drain grating/cover slab) asshown in drawings.

no $2.70 CE10025

(r) Other Works

9.200 Provide hole through existing manhole wall for sewer inletor outlet not exceeding 300mm diameter and make goodafter fixing (cost of pipe etc to be included).

no $27.30 CE10036

9.201 200mm diameter vitrified clay pipe inlet to manhole forhouse sewer connection including jointing and pluggingwith stopper (Cost of pipes etc included).

no $28.90 CE10037

of 82



9.202 Raise or lower level of manhole cover not exceeding300mm including breaking concrete, brickwork, re-concreting, re-fixing manhole cover and frame andmaking good after completion (Supply and installation ofprecast tube, if any, shall be measured separately).

no $469.50 G053

9.203 Painting and greasing of manhole frame and coverincluding preparation of surface by scraping andremoving of rust, mill scale concrete waste, etc.

no $24.60 G059

Tunnel with proper timber strutting, supply, lay andjoin flexible joint vitrified clay pipe with spigot andsocket rubber ring joint and concrete surround all asspecified:

9.204 225mm diameter. m $969.40 H002

Tunnel with proper timber strutting, supply, lay andjoin Class "M" concrete pipe with spigot and socketrubber ring joint and concrete surround all asspecified:

9.205 300mm diameter. m $1,191.60 H003

9.206 450mm diameter. m $1,402.00 H004

9.207 600mm diameter. m $1,668.30 H005

Pipe Jacking of vitrified clay pipes all as specified:

9.208 200mm diameter. m $442.80 CE10011

9.209 225mm diameter. m $488.80 CE10027

9.210 250mm diameter. m $534.80 CE10012

9.211 300mm diameter. m $603.80 CE10013

9.212 400mm diameter. m $649.80 CE10014

Pipe Jacking of Class "H" concrete pipe all asspecified:

9.213 225mm diameter. m $580.80 H011

9.214 300mm diameter. m $615.30 H012

9.215 375mm diameter. m $644.00 H015

9.216 450mm diameter. m $672.80 H013

9.217 525mm diameter. m $701.50 H016

9.218 600mm diameter. m $730.30 H014

of 82



9.2 DRAINS

(a) Half Round and Composite Drain Channels andBlock Drains

Half-round precast concrete drain channels true toline and level as shown in drawings:

9.219 150mm diameter (Type C1). m $9.00 J001






Precast concrete composite drain channels asspecified true to line and level as shown in drawings(Excavation, sand bed and bakau roller measuredseparately):

9.225 300mm (Type C7). m $28.80 J008

9 226 300mm (Type C7A) m $33 60 J0709.226 300mm (Type C7A). m $33.60 J070

9.227 300mm (Type C7B). m $32.80 J072

9.228 380mm (Type C8A). m $37.30 J009

9.229 455mm (Type C8B). m $60.10 J010

of 82



Standard precast concrete block drain as specified,true to line and level as shown in drawings(Excavation, sand bed and bakau rollers measuredseparately):

9.230 305mm (Type B1). m $29.30 J016

9.231 380mm (Type B2). m $33.80 J017

9.232 600mm (Type B3). m $67.80 J018

(b) Drain Opening Cover Slabs, Catch-Basin andOthers

9.233 3-piece precast concrete Grade 40 drain opening cover slab each size 277mm x 569mm x 25mm thick reinforced with a layer of 25mm x 25mm x 1.5mm thick fine mesh laid on and including 3mm thick galvanised mild steel flat plate and 64mm x 38mm x 4.5 mm thick galvanised mild steel angle frame to details as shown in drawings.

no $107.90 CE10029

9.234 Precast concrete Grade 40 drain opening cover slab overall size 277mm x 569mm x 25mm thick reinforced with a layer of 25mm x 25mm x 1.5mm thick fine mesh laid on and including 3mm thick galvanised mild steel flat plate to details as shown in drawings.

no $23.80 CE10030

9.235 Extra over for forming 1 no keyhole in precast concrete no $1.00 CE100319.235 Extra over for forming 1 no keyhole in precast concrete drain opening cover slab.

no $1.00 CE10031

9.236 Catch-basin overall size 780mm x 500mm x 575mm (forbus bay) including precast reinforced concrete slabcover, galvanised mild steel angle frame, base plate andaluminium vertical grating all as shown in drawings.

no $163.30 J074

9.237 Non-slip aluminium rungs 300mm wide, made out of25mm diameter aluminium ribbed rung type rods asshown in drawings.

no $25.10 J062

(c) Sub-soil Pipes and Scupper Drains

Perforated UPVC sub-soil pipe to SS141 Class "B"with flexible joints:

9.238 80mm diameter. m $9.00 CE10002

9.239 100mm diameter. m $9.10 K052

9.240 150mm diameter. m $12.80 K053

of 82



High density polyethylene (HDPE) part-perforatedcorrugated sub-soil pipe with plug-in connection:

9.241 DN 80 (80mm diameter). m $8.10 CE10016




9.245 250mm external diameter UPVC drain pipe to SS272(minimum wall thickness 6.1mm) with maximum one jointand Grade 30 reinforced concrete surround andhaunching to pipe laid on a layer of 100mm thick granitefine bed as shown in drawings.

m $73.70 K066

Provide hole through drain wall for UPVC pipe outlet,etc and make good after fixing for (UPVC pipemeasured separately):

9.246 100mm or 150mm diameter pipe outlet. no $3.30 K044

9.247 250mm diameter pipe outlet. no $5.40 K045

9.248 230mm wide x 450mm deep standard precast concreteopen scupper drain channel (Type S1) true to line andlevels as shown in drawings (Excavation, sand bed and

m $26.80 CE10026

levels as shown in drawings (Excavation, sand bed andbakau rollers measured separately).

9.249 Provide scupper opening (varies from 225mm to 250mmin width and 50mm to 75mm in height respectively)through drain wall using metal formwork.

no $6.10 CE10004

9.250 Precast concrete wall overall size 400mm x 300mm x150mm thick with 250mm wide x 75mm high scupperopening (with 4nos 10mm diameter mild steel bar).

no $22.80 CE11041

9.251 Precast concrete drop-inlet chamber 980mm x 475mm x425mm deep including hot-dipped galvanised mild steelhinged grating to details as shown in drawings.

no $138.00 K057

of 82



9.252 300mm x 300mm x 350mm deep (internal size) precastconcrete sump comprising of 100mm thick sides andbottom reinforced with WSF B6 and B5, T13mm diametersteel bars including 380mm x 380mm x 75mm precastconcrete cover slab reinforced with WSF A5 as shownin drawings.

no $58.50 K067

9.253 Precast concrete scupper mouth unit. no $15.70 K058

9.254 Precast concrete catch basin mouth unit, overall size1100mm x 250mm x 100mm thick (for bus bay) as shownin drawings.

no $19.50 CE10024

9.255 Crusher run sub-drains 300 mm wide x 375mm deepwrapped with synthetic membrane (geotextiles with aminimum flow rate of 150l/s/m2 (10cm head) and atensile strength of 400N/5cm) under footpaths or belowroad formation including necessary excavation.

m $17.10 L003

9.256 Add to last item for each additional 100mm increase indepth.

m $4.20 L020

(d) Weepholes

UPVC pipe to SS213:1979 as weephole not exceeding300mm long:

9.257 50mm diameter. no $2.40 M0099.257 50mm diameter. no $2.40 M009

9.258 65mm diameter. no $2.70 M042

9.259 80mm diameter. no $4.10 M010

9.260 100mm diameter. no $6.40 M011

9.261 300mm x 300mm Geotextile membrane to side of drainwall at weepholes all as specified.

no $1.70 CE10003

9.262 225mm x 225mm loose rubble packing to sides of drains,retaining walls etc behind weepholes including necessaryexcavation.

m $5.30 L004

9.263 500mm wide synthetic membrane (geotextiles with aminimum flow rate of 150l/s/m2 (10cm head) and atensile strength of 400N/5cm) strip to side of retainingwall, etc (excavation measured separately).

m $2.60 L021

of 82



(e) Silt Traps, Water Trough & Vibration Access

Reinforced Concrete temporary silt trap for drains,including unwashed sand bed to details as shown indrawings (excavation measured separately):

9.264 Overall size 1920mm x 2430mm x 1645mm depth (Type A).

no $1,805.90 CE10008

9.265 Overall size 2800mm x 4050mm x 2400mm depth, complete with 1200mm high timber fencing surround with one coat of enamel paint, set in and including concrete footings, "DANGER-KEEP OUT" warning signboards (Type B).

no $4,849.90 CE10009

9.266 Water trough, overall size 21200mm x 3500mm widecomprising of 200mm thick reinforced concrete base slaband 9000mm x 3500mm wide steel platform made out ofroll steel joists supports as framings to receive steelangle sections all welded together with and includingconcrete lining to details as shown in drawings(excavation and earth drain measured separately).

no $5,809.40 CE10022

9.267 Vibration access, overall size 6000mm x 3500mm widecomprising of 200mm thick reinforced concrete base slaband 2 nos of 6000mm x 1000mm wide steel platformmade out of mild steel angle sections asf i / t ll ld d t th ith d i l di

no $1,365.90 CE10023

framings/supports all welded together with and includinghardcore bed to details as shown in drawings (excavationand precast channel drain measured separately).

10. ROADS AND PAVINGS

10.1 Roads

(a) Road Base

10.01 Class 'A' synthetic geotextile membrane on roadformation.

m² $2.80 CE11018

10.02 50mm thick ash or unwashed sand bed on consolidatedroad formation.

m² $4.60 J054

10.03 Coarse granite aggregate (crusher run) road base blindedwith 20mm aggregate all as specified, deposited, spread,levelled, rolled and mechanically consolidated true tolevel and camber.

m³ $72.10 J073

of 82



10.04 Consolidation of road base with a powered roller. m² $1.90 J059

10.05 Plant Mixed Crushed Granite Aggregate (max. size 50mm& below), deposited, spread, levelled, rolled andmechanically consolidated true to level and camber.

m³ $51.60 J060

10.06 Sub-base materials (quarry/premix waste) deposited andcompacted to level and camber.

m³ $57.20 CE11017

(b) Bituminous Premix

Premix bituminous surfacing including rolling withlight and heavy rollers successively as specified(including bituminous emulsion tack coat):

10.07 Type "B1" to a consolidated thickness of 75mm. m² $22.30 CE11004



10.10 Type "W3" to a consolidated thickness of 25mm. m² $7.10 CE11007

10.11 Type "W3" to a consolidated thickness of 40mm. m² $10.90 CE11008

10.12 Type "W3B" to a consolidated thickness of 25mm. m² $7.10 CE11009

10 13 Type "W3B" to a consolidated thickness of 50mm m² $14 70 CE1101010.13 Type W3B to a consolidated thickness of 50mm. m $14.70 CE11010

10.14 Extra over for forming 1800mm wide hump with Type"W3B" premix including painting as shown in drawings.

m $55.90 CE11011

10.15 Extra over for forming 4000mm wide hump with Type"W3B" premix including painting as shown in drawings.

m $144.70 CE11012

10.16 Extra over for forming 5800 mm wide raised zebracrossing with Type "W3B" premix including painting asshown in drawings.

m $202.10 CE11027

of 82



The rate for mobilisation of plant and equipmentunder this sub-heading is applicable for the laying ofasphalt premix instructed by way of worksinstructions or works order given by the SO Rep.

10.17 Mobilisation of mechanical spreader for the laying ofasphalt premix including all necessary fuel and driver.

item $805.00 CE15036

10.18 Mobilisation of milling machine for the laying of asphaltpremix including all necessary fuel and driver.

item $2,501.30 CE15037

10.19 Mobilisation of mechanical sweeper for the laying ofasphalt premix including all necessary fuel and driver.

item $862.50 CE15038

10.20 Mobilisation of pneumatic type roller for the laying ofasphalt premix including all necessary fuel and driver.

item $805.00 CE15039

10.21 Mobilisation of static 10-tonne roller for the laying ofasphalt premix including all necessary fuel and driver.

item $805.00 CE15040

10.22 Mobilisation of vibratory roller for the laying of asphaltpremix including all necessary fuel and driver.

item $805.00 CE15041

10.2 PAVINGS

(a) Concrete Paving Slabs

Concrete paving slab including 50mm granite fines orConcrete paving slab including 50mm granite fines orunwashed sand bed and jointing in cement mortar(1:3):

10.23 50mm thick. m² $31.30 K012

10.24 75mm thick. m² $51.00 K011

10.25 100mm thick Grade 30 cast-in-situ concrete paving slabreinforced with WSF A10 reinforcement with patternedvoids at 200mm centre to centre formed by expandedpolystyrene formers as carpark lots, on 40mm thickgranite fines including necessary formwork and providingapproved soil mixture to voids and close turf with cowgrass as shown in drawings.

m² $56.90 K078

10.26 150mm thick Grade 30 cast-in-situ concrete paving slabreinforced with 2 layers of WSF A10 reinforcement withpatterned voids at 200mm centre to centre formed byexpanded polystyrene formers as lorry parking lots, on40mm thick granite fines including necessary formworkand providing approved soil mixture to voids and closeturf with cow grass as shown in drawings.

m² $78.00 K079

of 82



(b) BG Slabs

10.27 600mm x 400mm x 120mm "B.G. Slabs" on 50mm sandbed, topping up all voids with approved soil mixture andturfing including trimming and excavation to formation asshown in drawings.

no $12.80 K015

(c) Aeration Slabs

10.28 600mm x 600mm x 75mm thick precast concrete aerationslab reinforced with T9mm diameter steel bars on 40mmthick granite fines to carpark or tree planting areaincluding topping up all voids with approved soil mixtureand close turf with cow grass.

no $19.40 K019

10.29 75mm thick grade 30 concrete reinforcing tee overall size175mm x 175mm for corners of precast concrete aerationslabs reinforced with galvanised weldmesh 228.

no $3.70 B020

(d) Interlocking Concrete Paving Blocks

10.30 Interlocking paving slabs for carparking lots to approvedpattern comprising of 456mm x 456mm x 100mm thicknatural grey coloured perforated interlocking conreteslabs, 228mm x 114mm x 100mm thick colouredinterlocking concrete paving blocks with combination ofwhite coloured paving blocks for demarcation lines

m² $50.40 CE11033

white coloured paving blocks for demarcation lines,including 30mm thick compacted sand bed and toppingup voids with approved soil mixture and close turfing withcow grass and filling all joints with joint-filling sand asshown in drawings.

10.31 Coloured interlocking concrete paving blocks forhandicapped and motor-cycle parking lots comprising of228mm x 114mm x 100mm thick blocks laid to approvedpattern and with combination of white coloured pavingblocks for demarcation lines, including 30mm thickcompacted sand bed and filling all joints with joint-fillingsand as shown in drawings.

m² $46.60 CE11034

10.32 Coloured interlocking concrete paving blocks comprisingof 228mm x 114mm x 100mm thick blocks laid toapproved pattern including 30mm thick compacted sandbed and filling all joints with joint-filling sand as specified.

m² $43.50 CE11043

10.33 Extra over 228mm x 114mm x 100mm interlockingconcrete paving blocks for forming raised hump atlinkway service roads.

m² $7.90 CE11036

of 82



10.34 Extra over 228mm x 114mm x 100mm interlockingconcrete paving blocks for forming 1800mm wide roadhump across interlocking paving driveways.

m $13.00 CE11037

10.35 Extra over 228mm x 114mm x 100mm colouredinterlocking concrete paving blocks for forming handicaplogo with white coloured paving blocks.

no $58.30 CE11035

Coloured interlocking concrete paving blocks toapproved pattern including 50mm thick compactedsand bed and filling all joints with joint-filling sand asspecified:

10.36 Size 225mm x 112.5mm x 80mm thick. m² $41.00 SD077A

10.37 Size 225mm x 112.5mm x 100mm thick. m² $42.50 SD078A

10.38 Extra over 225mm x 112.5mm x 80mm thick interlockingconcrete paving blocks for forming raised hump atlinkway service roads comprising of plant mixed crushedgranite aggregate.

m² $10.60 CE11024

10.39 Extra over 225mm x 112.5mm x 80mm thick interlockingconcrete paving blocks for forming 1800mm wide roadhump across interlocking paving driveways as shown indrawings.

m $9.80 CE11001

(e) Expansion Joints( ) p

10.40 12mm wide x 25mm deep expansion joint filled with 40/50bitumen to cast-in-situ footpath and cycle track.

m $3.60 K024

10.41 15mm x 200mm deep self expanding cork with 25mmdiameter mild steel bar 600mm long half the lengthtreated with bituminous paint and its end covered with ametal cap bedded across the joint at 450mm centres andto details shown in drawings.

m $18.30 K074

10.42 13mm x 200mm compressed foam plastic strip. m $2.40 K026

10.43 25mm x 20mm x 2mm/5mm thick `L' shaped UPVCplastic strip laid to cast-in-situ drain top slab/concretepavement/kerb foundation as expansion joint as shownin drawings.

m $5.60 K070

10.44 Longitudinal joint of heavy duty sealant with T13mmdiameter bars x 800mm long spaced at 600mm centres todetail shown in drawings.

m $13.20 K076

of 82



10.45 25mm wide x 200mm deep expansion joint with FLEXCELL fibre board filler.

m $11.70 CE11044

10.46 175mm wide x 3mm thick lead bearing plate. m $19.50 CE11045

(f) Kerbs, Dividers, etc.

10.47 125mm x 125mm precast concrete kerb including jointingin cement mortar to details as shown in drawings.

m $10.70 K036

10.48 125mm x 300mm precast concrete kerb including jointingin cement mortar to details as shown in drawings.

m $15.40 K032

10.49 Extra over 125mm x 125mm precast concrete kerb forusing 125mm x 125mm x 300mm high precast concretekerb at sharp corners.

m $14.90 CE11042

Precast concrete kerb including jointing in cementmortar to details as shown in drawings :

10.50 125mm x 280mm (with 20mm diameter mild steel bar).

m $16.30 CE11014

10.51 125mm x 280mm x R350mm precast concrete kerb (with 2 nos 20mm diameter mild steel bars, each 150mm long).

no $14.90 CE11038

10.52 Extra over 125mm x 280mm precast concrete kerb forusing 125mm x 105mm - 160mm (overall plan size) x280mm high precast concrete kerb (with 20mm diametermild steel bar) for turning radius not exceeding 1.0m.

m $31.20 CE11031

10.53 Extra over 125mm x 280mm precast concrete kerb forusing 125mm x 260mm - 300mm (overall plan size) x280mm high precast concrete kerb (with 20mm diametermild steel bar) for turning radius exceeding 1.0m but notexceeding 2.0m.

m $12.90 CE11032

10.54 Extra over 125mm x 280mm precast concrete kerb forusing 125mm x 290mm - 300mm (overall plan size) x280mm high precast concrete kerb (with 20mm diametermild steel bar) for turning radius exceeding 2.0m but notexceeding 6.0m.

m $13.80 CE11039

of 82



10.55 Extra over 125mm x 280mm precast concrete kerb forusing 125mm x 300mm (overall plan size) x 280mm highprecast concrete kerb (with 20mm diameter mild steelbar) for turning radius exceeding 2.0m but not exceeding6.0m.

m $12.90 CE11040

Precast concrete divider kerb specially cast solidincluding jointing in cement mortar to details asshown in drawings:

10.56 300mm x 150mm. m $24.40 K037

10.57 380mm x 200mm. m $31.90 K038

10.58 190mm x 90mm red bull-nose brick kerb laid in cementmortar (1:3) all as shown in drawings.

m $17.10 K072

10.59 225mm x 150mm x 150mm precast concrete road lanedivider with 2 nos of 51mm diameter reflector discsecured to concrete surface and including painting,concrete foundation and excavation.

no $30.10 CE11046

10.60 Flexible reflective road lane divider including Grade 30concrete footing as shown in drawings.

no $86.70 CE11016

(g) Pipe Crossings

UPVC pipe to SS141 Class `B' for crossing with 3mmp p gdiameter nylon rope (minimum protruded length1000mm) including sand bed for car park/streetlighting:

10.61 80mm diameter. m $4.60 CE11019

10.62 100mm diameter. m $5.80 CE11020

10.63 150mm diameter. m $10.50 CE11021

Class 'B' galvanised iron pipes for crossing with 3mmdiameter nylon rope (minimum protruded length1000mm) including sand bed for car park/streetlighting:

10.64 80mm diameter. m $13.10 CE11022

10.65 100mm diameter. m $18.70 CE11023

of 82



11. SIGNAGES

(a) Directional Signs

11.01 80mm diameter Galvanised Iron Pipe Supports todirectional signboard welded with 200mm x 200mm x12mm thick mild steel plate and embedded in 400mm x400mm x 800mm depth Grade 20 concrete foundationincluding excavation as specified in drawings.

no $115.80 O067

125mm x 125mm x 6mm SHS Supports to directionalsignboard painted with one coat of red lead primerand two coats of approved quality paint, welded with300mm x 300mm x 12mm mild steel plate andembedded in Grade 30 concrete foundation includingexcavation as specified in drawings:

11.02 Supports with 600mm x 600mm x 1375mm deep concrete foundation.

pair $514.80 O068


pair $651.90 O081


pair $729.90 O082

Ill i d l i i b d i 1 00 900Illuminated plastic signboard size 1500mm x 900mmcomprising of 100mm x 23mm U-channel elephantgrey powder coated finish main frame filled in onboth faces with 5mm thick clear polycarbonate plastic sheet with green translucent sticker on the reverseside complete with all letterings, graphics/logos,hinges, masterkeyed locksets, fluorescent tubes,flexible electric cables and weather proof terminationbox and the signboard mounted onto and including2nos 3mm thick x 110mm diameter semi-circularnatural anodised aluminium post and all necessaryGrade 20 concrete foundation and excavation asspecified in drawings for:

11.05 Directional signboard for Apartment/Industrial Blocks. no $1,415.30 CE12042

11.06 Multi-storey carpark. no $1,415.30 CE12009

of 82



`Curve Alignment Marker' sign comprising of 1 no2.03mm (14SWG) thick aluminium base plate withdiamond grade retro-reflective sheetings withgraphics on one face to LTA's requirements asshown in drawings and fixed to hot-dippedgalvanised SHS posts for sign, set in and includingconcrete footings, excavation and disposal ofexcavated materials from site.

11.07 Size 600mm x 750mm (for Arterial Road). no $275.70 CE12044

11.08 Size 750mm x 900mm (for Expressway). no $393.80 CE12053

`Object Marker' sign comprising of 1 no 2.03mm(14SWG) thick aluminium base plate with diamondgrade retro-reflective sheetings with graphics on oneface to LTA's requirements as shown in drawings andfixed to hot-dipped galvanised SHS posts for sign, setin and including concrete footings, excavation anddisposal of excavated materials from site.

11.09 Size 600mm x 600mm. no $228.40 CE12054

11.10 Size 340mm x 900mm. no $200.10 CE12055

11.11 Size 900mm x 900mm. no $464.60 CE12056

11.12 `Barrier' sign size 1520mm x 400mm comprising of 1no2.03mm (14SWG) thick aluminium base plate withdiamond grade retro-reflective sheetings with graphics onone face to LTA's requirements as shown in drawingsand fixed to hot-dipped galvanised SHS posts, set in andincluding concrete footings, excavation and disposal ofexcavated materials from site.

no $421.10 CE12011

of 82



Block Directional Signboard comprising of 2 nos.aluminium framed 16 SWG aluminium sign plates,with diamond grade retro-reflective sheetings withnumerals, alphabets and arrows mounted to bothsides, fixed to and including 2 nos of 50.8mm x50.8mm x 4mm galvanised SHS supports (2700mmhigh from ground level) welded with 200mm x200mm x 6mm thick mild steel plate and embeddedin 350mm x 350mm x 500mm deep Grade 20 concretefoundation including painting and excavation asshown in drawings:

11.13 Size 1350mm x 750mm. no $1,164.90 CE12045

11.14 Size 1350mm x 550mm. no $881.40 CE12046

Road directional, confirmatory signboard and neighbourhood maps mounted on and including all necessary mild steel framing supports and painting (post and footing measured separately):

11.15 Comprising 1 no 14SWG aluminium base plate with diamond grade retro-reflective sheeting, letterings, numerals and figures on one face.

m2 $689.40 CE12051

11.16 Comprising 2 nos 14SWG aluminium base plates with diamond grade retro-reflective sheeting, letterings,

l d fi d f

m2 $815.90 CE12052

numerals and figures on exposed faces.

200mm high Street Name plate not exceeding 1.50mlength made out of aluminium `I' extrusion withdiamond grade retro-reflective sheeting (white) andvinyl film non reflective alphabets and numeralsprinted on both faces as shown in drawings:

11.17 Fixed to and including 50.8mm x 50.8mm x 4mm galvanised SHS post and base plate with concrete foundation and all necessary excavation and disposal of excavated material.

no $336.90 O079

of 82



200mm high Street Name plate not exceeding 1.50mlength made out of aluminium `I' extrusion withdiamond grade retro-reflective sheeting (white) andvinyl film non reflective alphabets and numeralsprinted on both faces as shown in drawings(Cont'd):

11.18 Fixed to lamp post with and including 25mm x 6mm thick aluminium flat bar cantilever support and 19mm stainless steel bands, buckles and other accessories (Type '2').

no $287.90 CE12027

11.19 Fixed to lamp post with and including purpose made holder of 20mm diameter aluminium pipe and 19mm wide stainless steel bands, buckles and other accessories (Type '1').

no $287.90 CE12026

11.20 5mm thick aluminium sign plate overall size 100mm x75/50mm with letterings for services crossing atdriveways including hacking of kerb and plastering signplate with cement mortar onto concrete kerb/drain kerb asshown in drawings.

no $14.20 CE12006

(b) Traffic Signs

Traffic Signs comprising of 2.03mm (14SWG) thickAluminium base plate with diamond grade retro-

fl ti h ti ith l tt i d hireflective sheetings with letterings and graphics onone face to LTA's requirements as shown in drawings(Irrespective of letterings and graphics):

11.21 600mm x 150mm and fixed to hot-dipped galvanised SHS post set in and including precast concrete footing, excavation and disposal of excavated materials from site.

no $86.70 P030

11.22 600mm x 400mm ditto. no $165.40 CE12001

11.23 600mm x 450mm ditto. no $181.20 P031

11.24 600mm x 600mm ditto. no $228.40 P032

11.25 600mm x 900mm ditto. no $322.90 CE12002

of 82



Traffic Signs comprising of 2.03mm (14SWG) thickAluminium base plate with diamond grade retro-reflective sheetings with letterings and graphics onone face to LTA's requirements as shown in drawings(Irrespective of letterings and graphics) (Cont'd):

11.26 2 nos. of 600mm x 600mm and fixed to hot-dipped galvanised SHS post set in and including precast concrete footing, excavation and disposal of excavated materials from site.

no $417.40 CE12003

11.27 2 nos. of 600mm x 600mm and 2 nos. arrow signs each 600mm x 150mm ditto.

no $511.90 CE12008

11.28 1 no. of 600mm x 900mm and 1 no. of 600mm x 450mm ditto.

no $464.60 CE12031

11.29 900mm x 900mm ditto. no $464.60 CE12032

11.30 2 nos. of 900mm x 900mm ditto. no $889.80 CE12033

11.31 900mm x 1200mm ditto. no $606.40 CE12034

11.32 600mm x 150mm and fixed to 6mm thick aluminium sign holder secured to lamp post by 19mm wide stainless steel band with buckle.

no $78.10 CE12015

11.33 600mm x 400mm ditto. no $156.80 CE12016

11.34 600mm x 450mm ditto. no $172.60 CE12017

11.35 600mm x 600mm ditto. no $219.80 CE12018

11.36 600mm x 900mm ditto. no $314.30 CE12019


11.38 2 nos. of 600mm x 600mm and 2 nos. arrow signs each 600mm x 150mm ditto.

no $585.80 CE12021

11.39 1 no. of 600mm x 900mm and 1 no. of 600mm x 450mm ditto.

no $481.90 CE12035

11.40 900mm x 900mm ditto. no $456.00 CE12037


11.42 600mm x 1200mm ditto. no $408.80 CE12036

11.43 900mm x 1200mm ditto. no $597.80 CE12039

of 82



"Exit" sign comprising of 2.03mm (14SWG) thickaluminium base plate with diamond grade retro-reflective sheetings with alphabets and arrows asshown in drawings:

11.44 Alternative À' (Single Face) with 50.8mm x 50.8mm x 4mm thick galvanised SHS post set in and including concrete footing, excavation and disposal of excavated materials from site.

no $228.40 CE12047

11.45 Alternative `B' (Single Face) with ditto. no $237.60 CE12048

11.46 Alternative À' (Double Face) with 40mm diameter galvanised iron class À' post set in and including concrete footing, excavation and disposal of excavated materials from site.

no $417.40 CE12049

11.47 Alternative `B' (Double Face) with ditto. no $426.60 CE12050

11.48 Alternative À' (Single Face) and fixed to 6mm thick aluminium sign holder secured to lamp post by 19mm wide stainless steel band with buckle.

no $219.80 CE12022

11.49 Alternative `B' (Single Face) and ditto. no $215.60 CE12023

11.50 Alternative À' (Double Face) and fixed to 6mm thick aluminium sign holder secured to lamp post by 19mm wide stainless steel band with buckle

no $434.70 CE12024

wide stainless steel band with buckle.

11.51 Alternative `B' (Double Face) and ditto. no $426.30 CE12025

11.52 "Handicap Logo" sign plate size 650mm x 650mm cum"Unauthorized Vehicles Fine $400" plate size 650mm x450mm comprising of 2.03mm (14SWG) thick aluminiumbase plate with diamond grade retro-reflective sheetingswith letterings and graphics on one face, hot dippedgalvanised SHS post for sign, set in and includingconcrete footing; excavation and disposal of excavatedmaterials from site.

no $419.70 CE12013

of 82



11.53 "NO ENTRY" sign plate size 600mm x 600mm cum"EXCEPT FIRE ENGINE" plate size 600mm x 400mmcomprising of 2.03mm (14SWG) thick aluminium baseplate with diamond grade retro-reflective sheetings withletterings and graphics on one face and fixed to hotdipped galvanised SHS post, set in and including precastconcrete footing, excavation and disposal of excavatedmaterials from site as shown in drawings.

no $354.40 CE12029

11.54 "Raised Zebra Crossing Ahead" sign plate, overall size600mm x 1200mm, comprising of 2.03mm (14SWG) thickaluminium base plate with diamond grade retro-reflectivesheetings with letterings and graphics on one face andfixed to hot-dipped galvanised SHS post set in andincluding precast concrete footing, excavation anddisposal of excavated materials from site as shown indrawings.

no $385.30 CE12030

"Pedestrian Alert" sign plate, overall size 450mm x450mm comprising of 2.03mm (14SWG) thickaluminium base plate with diamond grade retro-reflective sheetings with letterings and graphics onone face as shown in drawings:

11.55 Fixed to hot-dipped galvanised SHS post including concrete foundation and excavation.

no $145.70 CE12043

11 56 Fixed to 6mm thick aluminium sign holder secured to no $137 10 CE1205711.56 Fixed to 6mm thick aluminium sign holder secured to lamp post by 19mm wide stainless steel band with buckle.

no $137.10 CE12057

230mm diameter fibre glass deviation bollard,1000mm high above floor level complete with 300mmhigh with diamond grade retro-reflective sheetingsdirectional sign and with foot of bollard bolted to andincluding 205mm diameter x 6mm thick mild steelpipe welded on to 300mm x 300mm x 5.4mm thickmild steel base plate all as shown in drawings:

11.57 Deviation bollard on grass verge including all necessary concrete foundation.

no $283.40 CE12005

11.58 Deviation bollard on concrete footpath. no $283.40 CE12005

of 82



11.59 Hollow plastic reflector post, size 100mm x 120mm x1130mm, consisting of high density polyethylene in whitecolour with a black welded day-light marker and fitted with two round reflectors with foot fixed to 4.5mm thick hot-dipped galvanised hollow section and cast into concreteas shown in drawings.

no $55.30 CE12007

(c) Signboards

11.60 "DANGER-KEEP OUT" or other warning signboardsconsisting of 20mm thick timber board, complete withpainted background and wordings or signs by stencilprinting in colour in one or more languages of sizes600mm x 900mm and above but less than 1.0 sqmscrewed to m.s. brackets and supported by 30mm sq m.s. hollow section, elevated not less than 1.5m above groundlevel, complete with a concrete footing of 300mm x300mm x 600mm depth as approved by the S.O.'srepresentative.

no $40.00 Q021

11.61 Temporary sewer manhole sign comprising of 2.3mm (14SWG) thick aluminium base plate with engineering gradereflective sheet with graphics and letterings in red, whiteand black on one face and bolted onto a 40mm diametergalvanised steel pipe 2400mm long all as specified.

no $80.30 Q049

11 62 Temporary carpark sign plate size 900mm x 500mm no $96 00 CE1204111.62 Temporary carpark sign plate size 900mm x 500mmcomprising of 2.3mm (14 SWG) thick aluminium baseplate with engineering grade reflective sheet withgraphics and letterings on one face and bolted onto a hot-dipped galvanised post set in and including precastconcrete footing all as shown in drawings .

no $96.00 CE12041

11.63 Project Signboard comprising of 12mm thick plywood(2400mm x 1200mm) with enamel painted backgroundand letterings, mounted on 50.8mm x 50.8mm x 6.4mmthick galvanised SHS frame with 25mm x 25mm x 2mmgalvanised SHS stiffeners fixed to 2nos 76.2mm x76.2mm x 6.4mm thick galvanised SHS supports(3075mm high from ground level) welded with 200mm x200mm x 6mm thick mild steel base plate embedded in400mm x 400mm x 600mm deep Grade 20 concretefoundation including painting and excavation as specifiedin drawings.

no $1,230.50 O074

11.64 800mm diameter convex mirror, fixed to and supported by1 no 75mm diameter galvanised iron pipe and embeddedin 400 x 400 x 500mm deep Grade 25 concretefoundation and all necessary excavation.

no $284.80 CE12012

of 82



12. GATES AND FENCING

(a) Gates

12.01 Double leaf gate consisting of 50mm diameter galvanisediron tubular framing filled in with 50mm x 50mmweldmesh, 75mm diameter galvanised iron tubular gateposts with bottom end encased in 450mm x 450mm x600mm Grade 20 concrete foundation, the gates hung on2 Nos. pairs approved hooks and ride hinges and fittedwith approved locking bolt including all necessary weldingand painting. (Nett area of leaf measured).

m² $62.70 N001

12.02 Standard metal collapsible gates of approvedmanufacture including all necessary fixing lugs, guiderails, rollers and gate locks etc.

m² $147.10 N002

(b) Chain Link Fencing

3.175mm thick gauge x 50mm mesh PVC chain linkfencing of the following height to top of mesh with 3Nos. horizontal lines of double strand 2.517mm BGgalvanised barbed wires of 2- ply 4 point above at 100mm centres, the chain link and barbed wires fixed toand including 50mm x 50mm x 6mm angle iron postsat 3m centres with top bent to form spurs and bottomcast into 300mm x 300mm x 450mm deep Grade 20cast into 300mm x 300mm x 450mm deep Grade 20concrete foundations including all necessarystraining wires and split pins and priming andpainting posts with two coats aluminium paint:

12.03 1.20m high. m $36.60 N003

12.04 1.50m high. m $40.60 N004

12.05 1.80m high. m $45.50 N005

12.06 2.10m high. m $56.00 N006

12.07 2.40m high. m $63.90 N007

(c) Temporary Fencing

12.08 Temporary fencing 1.20m high consisting of 6 Noslongitudinal lines of galvanised double strand 2.517mmBG barbed wire stapled 150mm and 225mm apart, asshown in drawings and including 80mm diameter bakauposts with pointed bottom and driven 450mm deep intoground at 3.0m centres.

m $12.30 N009

of 82



12.09 Temporary fencing 1.20m high consisting of 3 Noshorizontal lines of galvanised doubled strand 2.517mmBG barbed wire stapled 300mm apart to and including100 mm diameter bintangore posts with pointed bottomand driven 450mm deep into ground at 2.40m centres.

m $8.20 N010

12.10 Temporary fencing 1.20m high consisting of 6 Noshorizontal lines of galvanised doubled strand 2.517mmBG barbed wire stapled 150mm apart to and including100 mm diameter bintangore posts with pointed bottomand driven 1.0m deep into ground at 2.50m centres.

m $12.60 N027

12.11 Dismantling and removing chain link fencing 1.5m highincluding breaking up of foundation etc.

m $12.90 N011

12.12 Add to last item for each additional 300mm height. m $2.00 N012

12.13 20mm thick temporary wooden fence vertically spacedalternately with 100mm x 100mm vertical standard at2.5m centres to centres spaces with 2 Nos. of 100mm x50mm horizontal guides to a height 1.500m, using sawntimber with wood preservative.

m $35.10 N013

13. SITE CLEARANCE, TURFING AND TREE-PLANTING

(a) Site Clearance

13.01 To clear and cart away debris from site to approved ENVdumping ground.

ton $97.30 L010

13.02 Clearing and disposal of bush, belukar, holes and anyother undergrowth etc from site including removing fromsite and dumping at approved dumping ground.

m² $4.00 L011

Cut down trees with girth measured at a point 1.0mabove the ground, grub up roots and clear away fromsite:

13.03 Not exceeding 0.5m girth. no $208.30 CE14001

13.04 Exceeding 0.5m but not exceeding 1.0m girth. no $256.50 L012


of 82



Cut down trees with girth measured at a point 1.0mabove the ground, grub up roots and clear away fromsite (Cont'd):




13.09 Exceeding 3.0m but not exceeding 4.0m girth. no $1,050.90 L017



(b) Turfing

13.12 Labour for trimming and forming embankments. m² $2.20 M002

13.13 225x225mm spot turfing (with 25mm thick original topsoil) at 450mm centre both directions with a layer ofapproved soil mixture 125mm thick including themaintenance of the turfing works during the "MaintenancePeriod" as specified.

m² $7.10 SM002A

13.14 Strip turfing (with 25mm thick original top soil) 450mmwide and spaced 600mm between strips at an angle of 45

m² $10.60 SM004Ap p g

degree on embankments with a layer of approved soilmixture 125mm thick including the maintenance of theturfing works during the "Maintenance Period" asspecified.

Close turfing (with 25mm thick original top soil)including the maintenance of the turfing works duringthe "Maintenance Period" as specified:

13.15 To slope embankment with a layer of 125mm thick approved soil mixture.

m² $13.10 SM009

13.16 To flat level surfaces with a layer of 125mm thick approved soil mixture.

m² $12.20 SM011

13.17 To slope embankment with a layer of 225mm thick approved soil mixture.

m² $14.80 CE14002

13.18 To flat level surfaces with a layer of 225mm thick approved soil mixture.

m² $13.80 CE14003

13.19 Grass cutting at aeration slabs including weeding, sweepand remove cut grass off site. (Includes area occupiedby aeration slabs but exclude concrete lining).

m² $0.30 M038

of 82



13.20 Grass cutting including weeding on level ground or slopeembankments, sweep and remove cut grass off site andtrimming edges at drain kerbs and roadsides, etc.

m² $0.10 M053

(c) Tree Pruning

Trimming of tree branches terminals and clearing of cut branches, debris etc from site. (The height of tree measured from tree base to the highest growing point of tree before pruning):

13.21 Tree height not exceeding 2m. p/tree $6.40 CE14004

13.22 Tree height exceeding 2m but not exceeding 3m. p/tree $16.50 CE14005

13.23 Tree height exceeding 3m but not exceeding 6m. p/tree $46.50 CE14006

13.24 Tree height exceeding 6m but not exceeding 9m (truck mounted hydraulic platform measured separately).

p/tree $63.20 CE14007

13.25 Tree height exceeding 9m but not exceeding 12m (truck mounted hydraulic platform measured separately).

p/tree $94.50 CE14008

13.26 Tree height exceeding 12m but not exceeding 15m (truck mounted hydraulic platform measured

p/tree $146.20 CE14009(truck mounted hydraulic platform measured separately).

13.27 Tree height exceeding 15m (truck mounted hydraulic platform measured separately).

p/tree $198.20 CE14010

(d) Tree Planting

13.28 Excavate trench to form shrub/flower bed, includingbackfilling to level about 250mm above the adjacentground level with approved soil mixture as specified(plants measured separately).

m³ $47.40 SM018

Excavate tree hole including backfill to a level 250mmabove ground with approved soil mixture as specified(tree measured separately):

13.29 1.50 x 1.50 x 1.00m deep. no $104.90 SM078

13.30 1.00 x 1.00 x 1.00m deep. no $46.60 SM077

13.31 0.50 x 0.50 x 0.50m deep. no $6.60 SM079

of 82



Planting of instant tree including maintenance asspecified (tree measured separately):

13.32 Not exceeding 300mm girth. no $4.20 SM080

13.33 Exceeding 300mm but not exceeding 500mm girth. no $5.50 SM081

Planting of tree saplings/fruit trees/palms includingmaintenance as specified (tree measured separately):

13.34 Large size with minimun height 2.00m. no $3.50 SM082

13.35 Medium size with minimun height 1.50m. no $2.80 SM083

13.36 Small size with minimun height 1.00m. no $2.10 SM084

13.37 Planting of shrubs of any size including maintenance asspecified (shrub measured separately).

no $1.10 SM085

13.38 Approved good quality top soil (From contractor's ownsource).

m³ $28.80 Q016

13.39 Tree guard with minimum 50mm diameter Bintangorepoles tied together with galvanised wire bracing as shownin drawings.

no $21.90 SM041

Approved green plastic netting surrounding all the sides of tree guard to a height of 200mm above the ground:

13.40 Single layer. m2 $1.40 SM043

13.41 Double layer. m2 $2.90 SM044

13.42 Loamy soil to planting strip as shown in drawings. m³ $42.90 Q018

13.43 Trough of uniform 20mm aggregate wrapped withsynthetic fabric membrane all round as shown indrawings.

m³ $55.30 Q019

13.44 100mm diameter x 650mm long UPVC perforated pipe toSS141 with PVC perforated cover and galvanised steelclearing plate as shown in drawings.

no $11.10 Q020

of 82



14. REPAIR WORKS SECTION

(a) Break-up and replacement

Break up and remove from site existing surfaceobstruction consisting of the following materials:

14.01 Bituminous surfacing including granite sub-base. m³ $50.00 J065

14.02 Reinforced concrete. m³ $138.60 J066

14.03 Mass concrete. m³ $111.00 J067

14.04 Brickwork and blockwork. m³ $73.90 J068

14.05 Scarify existing road surfacing 75mm deep and removeall scarified materials and brush clean road base toreceive new surfacing.

m² $6.40 J047

Cold mill existing road surfacing and remove allmilled materials and brush clean road base to receivenew surfacing:

14.06 Not exceeding 25mm deep. m² $4.20 J069

14.07 Exceeding 25mm but not exceeding 50mm deep. m² $5.10 J063

14 08 E di 50 b t t di 75 d ² $6 70 J06414.08 Exceeding 50mm but not exceeding 75mm deep. m² $6.70 J064

14.09 Break up existing roadside kerb size 125mm x 300mmincluding concrete foundation and remove debris fromsite.

m $21.80 A011

14.10 Add to (or deduct) from last item for each size over orbelow 0.01 m2 cross sectional area of kerb.

m $4.20 A012

14.11 Take out precast concrete paving / revetment slabs(thickness not exceeding 200mm) and stack up for re-use.

m² $8.70 J012

14.12 Select from stack and lay precast concretepaving/revetment slabs (thickness not exceeding 200mm)including the provision of 50mm bed of granite dust orunwashed sand.

m² $8.30 J013

14.13 Take up precast concrete paving slabs (thickness notexceeding 200mm) to footpaths and replace oncompletion including laying a layer of 50mm sand bed.

m² $14.70 A009

of 82



14.14 Take out precast aeration / perforated interlockingconcrete turf paving slabs (thickness not exceeding200mm) including removal of earth and turf and stack upfor re-use.

m² $8.90 K021

14.15 Take out precast aeration / perforated interlockingconcrete turf paving slabs (thickness not exceeding200mm) including removal of earth and turf and cart awayfrom site.

m² $4.40 CE15028

14.16 Select from stack and lay precast aeration / perforatedinterlocking concrete turf paving slabs (thickness notexceeding 200mm) including 40mm thick bed of granitefines and filling all voids with approved soil mixture andturf.

m² $24.90 K022

14.17 Take out interlocking concrete paving blocks (thicknessnot exceeding 200mm) and cart away materials from site.

m² $5.40 CE15029

14.18 Removal of encrusted top soil and earth (averagethickness not exceeding 200mm) from slots and gapsbetween aeration slabs and replace with approved soilmixture and turf (measured as area of aeration slabs).

m² $8.60 K023

14.19 Take up concrete revetment slabs (thickness notexceeding 200mm) and inverts to surface water drainsand reinstating to the satisfaction of the S.O.'s

m $27.80 A010

representative on completion. Allow for dealing with allwater in the drains by pumping or by diversion.

14.20 Take out precast concrete composite drain channel (sizenot exceeding 500mm wide) and stack up for re-use.

m $12.80 J014

14.21 Select from stack and lay precast concrete compositedrain channel (size not exceeding 500mm wide) includingjointing in cement mortar (1:3).

m $13.80 J015

(b) Refixing handrailings

Materials and labour for re-fixing of handrailing (2rows) including foundation, cutting of pipes etc and 3coats of approved paint (Rate excludes cost ofhandrailing).

14.22 40mm diameter handrailing. m $23.50 M048



of 82



(c) Erasing roadline and markings

Erase off existing road lines and markings in the coldstate with a road line erasing machine includingsweeping all shavings off the road:

14.25 100mm wide line. m $1.70 O039

14.26 Single 100mm wide zig-zag line (measured straight along the edge of road/kerb).

m $1.40 CE15033

14.27 Double 100mm wide zig-zag line (measured straight along the edge of road/kerb).

m $2.80 CE15034

14.28 150mm wide line. m $2.50 O040

14.29 200mm wide line. m $4.10 O041

14.30 300mm wide line. m $6.80 O042

14.31 455mm wide line. m $10.80 CE15035

14.32 Single traffic arrow / Merging arrow. no $43.50 O043

14.33 Double traffic arrow. no $51.50 O044

14.34 Triple traffic arrow. no $60.70 O045




14.38 Standard numerals 180mm height. no $4.60 CE15032

14.39 Pedestrian crossings and other road markings exceeding 455mm wide.

m² $18.40 O048

of 82



15. DAYWORKS

Provide the undermentioned labour and ConstructionEquipment (Operator and fuel included) and materialsas may be ordered in writing by the S.O.'sRepresentative.

(a) Labour(excluding profit & overhead)

15.01 Bricklayer. hr $11.90 SN001

15.02 Carpenter. hr $13.40 SN003

15.03 Concretor. hr $12.50 SN004

15.04 Drainlayer. hr $12.40 SN006

15.05 Fitter. hr $14.40 SN008

15.06 Labourer. hr $8.60 SN012

15.07 Mason. hr $11.90 SN014

15.08 Painter. hr $11.70 SN016

15.09 Pavior. hr $12.20 SN017

15 10 Roller Driver hr $17 30 SN02215.10 Roller Driver. hr $17.30 SN022

15.11 Steel Bender & Fixer. hr $12.60 SN025

15.12 Watchman. hr $10.70 SN029

15.13 Welder. hr $11.40 SN030

of 82



(b) Construction equipment (excluding profit &overhead)

15.14 Air blower - 300mm diameter, 230V complete with 5mduct e.g. Kenki model AP3 (including generator and multi-gas monitor).

hr $69.90 SN082

15.15 Air compressor with air deliver of 4.5 cu m/ per minuteand working pressure of 7 kg/cm2 including pneumatictools, fuel and tool sharpening (no labour).

hr $24.70 SN032

15.16 Concrete mixer - 200/140 litres capacity including fuel. hr $15.60 SN033

15.17 Concrete mixer - 300/200 litres ditto. hr $22.90 SN034

15.18 Crane (KATO KR20H) including fuel and driver. hr $118.10 SN050

15.19 Crawler excavator with back hoe or dragline 0.85 m3

bucket including fuel and driver. e.g. Kobe 907.

hr $101.60 SN063

15.20 Crawler mounted crane 25 tonne lifting capacity includingfuel and driver.

hr $106.60 SN079

15.21 Diamond cutter including fuel and driver. hr $23.50 SN061

15.22 Diesel dumper not exceeding 0.75 cu m capacityincluding fuel and driver.

hr $32.70 SN058

15.23 Diesel powered field welding machine with minimumcapacity 300 amp.

hr $15.40 SN036

15.24 Kobe 904 with breaker including fuel and driver. hr $108.00 SN056

15.25 Kobe 907 with breaker ditto. hr $122.60 SN057

15.26 Lorry crane (up to 3 tonne) including fuel and driver. hr $43.60 SN067

15.27 Ditto - (5.5 to 7 tonne) ditto. hr $58.00 SN068

15.28 Ditto - (up to 10 tonne) ditto. hr $81.50 SN069

15.29 Mechanical rammer with impact force not exceeding 4000kg per blow.

hr $20.20 SN080

15.30 Mechanical road sweeper with a minimum rating of 44 hpincluding fuel and driver.

hr $89.10 SN060

of 82



15.31 Mini-backhoe excavator (not exceeding 0.2 cu m)including fuel and driver. eg Airman HS20S.

hr $41.70 SN062

15.32 Motor crane (5 ton lifting capacity) including fuel anddriver.

hr $59.90 SN078

15.33 Motor crane (8 - 13 tonne lifting capacity) including fueland driver.

hr $75.70 SN051

15.34 Motor grader - 3650mm blade (101 kw range) includingfuel and driver e.g. 120 G Tractor.

hr $89.50 SN070

15.35 Ditto - 4270mm blade (134 kw range) ditto. hr $96.20 SN071

15.36 Ditto - 4880mm blade (186 kw range) ditto. hr $111.40 SN072

15.37 Motor lorry (pick-up) 1.50 tonne size including fuel &driver.

hr $27.30 SN053

15.38 Motor lorry 2.5 - 3 tonne size ditto. hr $30.10 SN039

15.39 Motor lorry or Tipper 5.5 - 7.0 tonne size ditto. hr $48.60 SN040

15.40 Motor lorry or Tipper 10 tonne size ditto. hr $57.90 SN052

15.41 Oxy-acetylene cutter including welder. hr $47.90 SN081

15.42 Power driven pump - 50mm size including fuel. hr $21.50 SN041

15.43 Power driven pump - 75mm size ditto. hr $27.30 SN042



15.46 Power wheel loader of 1.5 cu m bucket capcity includingfuel and driver. Flywheel horsepower 100HP (range) e.g.Cat 930.

hr $81.40 SN065

15.47 Ditto but exceeding 1.5 cu m bucket capacity but notexceeding 2.5 cu m capacity including ditto. Flywheelhorsepower 130HP (range) e.g. Cat 950.

hr $86.20 SN066

15.48 Road roller 8 to 10 tonne capacity including fuel anddriver.

hr $42.10 SN045

15.49 Road roller vibrating 10 to 20 tonne capacity includingfuel and driver.

hr $43.00 SN083

15.50 Tandem roller 1 tonne capacity including fuel and driver. hr $20.20 SN059

of 82



15.51 To provide collision attenuator or truck mountedattenuator (TMA) attached/fitted/mounted onto anappropriate shadow vehicle complete with signboards,blinkers, lights, cones, etc and all necessary equipmentfor traffic control and road safety all in accordance withLTA's Code of Practice on Temporary Traffic Control.(Rate is only applicable by way of works instruction orworks order given by SO Rep).

Per day $450.00 SN084

15.52 Track type tractors as bulldozer or ripper FlywheelHorsepower (67 kw range) including fuel and driver e.g.CAT D5.

hr $87.80 SN073

15.53 Ditto (104 kw range) ditto. e.g. CAT D6D. hr $102.20 SN074

15.54 Ditto (149 kw range) ditto. e.g. CAT D7. hr $111.40 SN075

15.55 Ditto (224 kw range) ditto. e.g. CAT D8. hr $167.10 SN076

15.56 Ditto (306 kw range) ditto. e.g. CAT D9H. hr $179.70 SN077

15.57 Traxacavator - 1.0 cu m bucket capacity range includingfuel and driver. e.g. CAT 933.

hr $84.80 SN046

15.58 Ditto - 1.5 cu m ditto. e.g. CAT 955. hr $91.40 SN047



15.61 Wheel or crawler shovel or excavator loaders with backhoe bucket not exceeding 0.4 cu m or 1.30 cu m loaderbuckets capacity including fuel and driver. e.g. Kobe904, JCB.

hr $80.60 SN049

STANDARD SCHEDULE OF RATES FOR ELECTRICAL WORKS (JUL 2013)



FOR

ELECTRICAL WORKS (JUL 2013)

CONTENTS

S/N DESCRIPTION PAGE

GENERAL PREAMBLES 1- 3

ELECTRICAL INSTALLATIONS

A POINT WIRING 4 - 6

B POWER/HEATER POINT 7 - 11

C CIRCUIT WIRING 11 - 18

D CABLE SUPPORT SYSTEMS 19 - 21

E ELECTRICAL ACCESSORIES 22 - 29

F LUMINAIRES 29 -30

G LIGHTNING CONDUCTORS AND EARTH RODS 30 - 31

H EXTERNAL LIGHTING 32 - 63

I EMERGENCY/EMERGENCY EXIT SIGN LUMINAIRES 63 - 64

J FIRE ALARM ACCESSORIES 65

K TELEVISION SYSTEM 66 -69

Published by Housing and Development Board, Republic of Singapore



of 69

GENERAL PREAMBLES 1 Introduction 1.1 The clauses in the General Preambles shall apply to all work items

contained in the Standard Schedule of Rates. 1.2 All rates include the allowances for complying with the General

Preambles. 2 All rates contained in the Standard Schedule of Rates are fixed basic

rates (in Singapore Currency) and no amendment whatsoever shall be made to such rates. The tenderers shall be deemed to have closely studied all rates contained herein and duly noted their implications.

3 All rates contained in the Standard Schedule of Rates are exclusive of

any Goods and Services Tax. Any such Goods and Services Tax shall be borne by the HDB as and when the same becomes due and payable.

4 All work, materials and goods described in this Standard Schedule of

Rates shall be of the respective kinds described in the Contract and in accordance with the instructions of the Superintending Officer or the Superintending Officer's Representative.

5 Headings to groups of items shall be read as part of the descriptions of

the items to which the headings apply. 6 Where brand/trade names are given in the descriptions, they are solely

intended for fixing the rates of the items. The products and materials to be used in the contract shall be governed by the specifications, drawings and other documents forming the contract (and not this Schedule of Rates).

7 Description of Works and Inclusions Unless specifically stated otherwise, the following shall be deemed to

be included in the description of the item of work:-

a) Labour and all costs in connection therewith including the labour in fabricating, assembling, setting, fitting and fixing of materials and goods in position.

b) Materials and goods including materials required for lapping,

jointing and the like and all costs in connection therewith such as conveyance, delivery, unloading, storing, returning of packings, handling, hoisting and lowering.

of 69

GENERAL PREAMBLES 7 Description of Works and Inclusions (Cont'd) c) Preparing surfaces to receive work.

d) Protecting materials and work.

e) Waste of materials.


g) Use of construction equipment, tools, vehicles and all costs in connection therewith.


i) General requirements set out in the Specifications, Drawings

and other documents forming the Contract.

j) Establishment charges, overhead and profit. 8 The description of each item of work shall be deemed to include all

screws, nails, bolts, nuts, nipples, fixing or supporting clips, saddles, brackets, straps, rivets, plugs and the like and all incidental accessories, chases, holes, mortises, cutting away plugging and making good of walls, ceilings and other structural features where necessary.

9 All metal conduits shall be deemed to include socket joints. 10 Unless otherwise stated, all work shall be measured nett as fixed in its

place. 11 Unless otherwise stated, pipes are described by their internal

diameters. 12 Where minimum deductions of voids are dealt with in this document

they shall refer only to openings or voids which are within the boundaries of measured area. Openings or voids which are at the boundaries of area shall always be the subject of deductions irrespective of size.

13 Billing of Quantities 13.1 Where the unit of measurement is the linear metre, square metre and

cubic metre, quantities shall be billed to the nearest whole unit. Fractions of the unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit.

of 69

GENERAL PREAMBLES

13 Billing of Quantities (Cont'd)

13.2 Where the unit of measurement is the kilogramme, quantities shall be billed to the nearest whole unit. Fractions of a unit less than half shall be disregarded and all other fractions shall be regarded as a whole unit. Where the unit of billing is the tonne or litre, quantities shall be billed to the nearest two places of decimals.

13.3 Where the unit of measurement is the hour, fractions of the unit shall

be billed to the nearest next half hour. 13.4 Where the application of clauses 13.1 and 13.2 would cause an entire

item to be eliminated, such item shall be billed to the nearest two places of decimals.

14 Where rates with descriptions pertain to the same purpose are listed in

more than one Standard Schedule of Rates incorporated in the Contract; the rate as listed in the following schedules (in the stated order of precedence) shall prevail:-

1st Precedence Standard Schedule of Rates for Building

Works

2nd Precedence Standard Schedule of Rates for Civil Engineering Works

3rd Precedence Standard Schedule of Rates for Electrical Works

15 Unless otherwise stated, the term "as specified" means as specified in

any of the documents forming part of the Contract. 16 The following abbreviations are used for the units:- m - Linear metre m2 - Square metre m3 - Cubic metre no - Number kg - Kilogram ton - Tonne pr - Pair sht - Sheet ltr - Litre hr - Hour

of 69

HOUSING AND DEVELOPMENT BOARDSTANDARD SCHEDULE OF RATES FOR ELECTRICAL WORKS (JUL 2013)


ELECTRICAL INSTALLATION

A POINT WIRING

Wiring In PVC Trunking

Surface wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable in PVC trunking including accessories butexcluding fittings, fan regulators and fans:

1 One lighting or fan point controlled by one switch (to a distance not exceeding 12m).

no $61.40 SZ001

2 Each additional point to item SZ001 (to a distance not exceeding 5m).

no $26.70 SZ002

3 Each additional point to item SZ001 (to a distance exceeding 5m but not exceeding 10m).

no $44.80 SZ003

4 One lighting point controlled by two 2-way switches (to a distance not exceeding 12m).

no $77.80 SZ004

Surface wiring in 2x1.5mm² PVC/PVC cable and 1.5mm² earth cable in PVC trunking including accessories butexcluding light fittings, fan regulators and fans:

5 One lighting or fan point controlled by one switch (to adistance not exceeding 12m).

no $67.60 SZ005


no $29.30 SZ006


no $50.00 SZ007


no $86.10 SZ008

Wiring in Metal Conduit

Surface wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable in 20mm diameter metal conduit includingaccessories but excluding light fittings, fan regulatorsand fans:


no $111.50 SZ009

of 69



A POINT WIRING (CONT'D)

Wiring in Metal Conduit (Cont'd)

Surface wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable in 20mm diameter metal conduit includingaccessories but excluding light fittings, fan regulatorsand fans (Cont'd):


no $42.90 SZ010


no $81.90 SZ011


no $132.60 SZ012

Surface wiring in 2x1.5mm² PVC/PVC cable and 1.5mm² earth cable in 20mm metal conduit includingaccessories but excluding light fittings, fan regulatorsand fans:


no $117.70 SZ013


no $48.50 SZ014


no $87.10 SZ015


no $140.90 SZ016

Concealed Wiring In PVC Pipe Conduit

Concealed wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable, drawn through and including 20mmdiameter PVC pipes cast/embedded in slab/wallcomplete with all necessary tees, connectors, outletjunction box and accessories but excluding fittings,fan regulators and fan:


no $60.30 SZ909

of 69



A POINT WIRING (CONT'D)


Concealed wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable, drawn through and including 20mmdiameter PVC pipes cast/embedded in slab/wallcomplete with all necessary tees, connectors, outletjunction box and accessories but excluding fittings,fan regulators and fan (Cont'd):


no $24.90 SZ910


no $42.50 SZ911


no $77.60 SZ912

Concealed wiring in 2x1.5mm² PVC cable and 1.5mm²earth cable, drawn through and including 25mmdiameter PVC pipes cast/embedded in slab/wallcomplete with all necessary tees, connectors, outletjunction box and accessories but excluding fittings,fan regulators and fan:


no $62.80 SZ913


no $26.00 SZ914


no $44.60 SZ915


no $81.70 SZ916

25 Bell point complete with concealed wiring in 2x1.5mm2 PVC cable and 1.5mm2 PVC earth cable drawn through and including 20mm diameter PVC pipes embedded in slab/wall complete with all necessary tees, connectors, outlet junction and accessories but excluding bell (to a distance not exceeding 12m).

no $61.70 SZ960

of 69



B POWER/HEATER POINT

Wiring In PVC Trunking

13 amp 1-gang white switch socket-outlet completewith mounting box in 60x20mm PVC multi-compartment trunking including accessories:

26 Surface wiring in 2x2.5mm² PVC cable and 2.5mm² earth cable (to a distance not exceeding 12m).

no $71.10 SZ017


no $35.30 SZ310


no $58.00 SZ311

29 Surface wiring in 2x2.5mm² PVC/PVC cable and 2.5mm² earth cable (to a distance not exceeding 12m).

no $78.20 SZ018


no $38.20 SZ312


no $63.90 SZ313

13 amp 2-gang white switch socket-outlet completewith mounting box in 60x20mm PVC multi-compartment trunking including accessories:


no $76.70 SZ470


no $40.90 SZ471


no $63.60 SZ472


no $83.80 SZ473

of 69



B POWER/HEATER POINT (CONT'D)

Wiring In PVC Trunking (Cont'd)

13 amp 2-gang white switch socket-outlet completewith mounting box in 60x20mm PVC multi-compartment trunking including accessories (Cont'd):


no $43.80 SZ474


no $69.50 SZ475

15 amp switch socket-outlet complete with mountingbox in 60x20mm PVC multi-compartment trunkingincluding accessories (to a distance not exceeding12m):

38 Surface wiring in 2x2.5mm² PVC cable and 2.5mm² PVC earth cable.

no $78.40 SZ021

39 Surface wiring in 2x2.5mm² PVC/PVC cable and 2.5mm² PVC earth cable.

no $85.40 SZ022

Wiring in Metal Conduit

13 amp 1-gang metal-clad switch socket-outletcomplete with mounting box in 20mm diameter metalconduit including socket joints and other accessories:


no $113.60 SZ019


no $56.30 SZ314


no $97.00 SZ315


no $120.70 SZ020

of 69




Wiring in Metal Conduit (Cont'd)

13 amp 1-gang metal-clad switch socket-outletcomplete with mounting box in 20mm diameter metalconduit including socket joints and other accessories(Cont'd):


no $59.20 SZ316


no $102.90 SZ317

13 amp 2-gang metal-clad switch socket-outletcomplete with mounting box in 20mm diameter metalconduit including socket joints and other accessories:


no $161.90 SZ476


no $81.60 SZ477


no $138.70 SZ478


no $168.90 SZ479


no $84.60 SZ480


no $144.60 SZ481

15 amp metal-clad switch socket-outlet complete withmounting box in 20mm diameter metal conduitincluding socket joints and other accessories (to adistance not exceeding 12m):

52 Surface wiring in 2x2.5mm² PVC cable and 2.5mm² PVC earth cable.

no $119.90 SZ023

53 Surface wiring in 2x2.5mm² PVC/PVC cable and 2.5mm² PVC earth cable.

no $127.00 SZ024

of 69





13 amp 1-gang white plate switch socket-outlet pointwith mounting box comprising of cables drawnthrough and including 20mm diameter PVC pipescast/embedded in slab/wall complete with tees,connectors and other accessories:

54 Concealed wiring in 2x2.5mm² PVC cable and 2.5mm² earth cable (to a distance not exceeding 12m).

no $63.20 SZ917


no $30.80 SZ918


no $50.20 SZ919

13 amp 1-gang white plate switch socket-outlet pointwith mounting box comprising of cables drawnthrough and including 25mm diameter PVC pipescast/embedded in slab/wall complete with tees,connectors and other accessories:


no $65.70 SZ920


no $31.90 SZ921


no $52.20 SZ922

60 Extra over the items SZ917 to SZ919 and SZ920 to SZ922for 13-amp 2-gang white plate switch socket-outlet pointcomplete with mounting box.

no $8.90 SZ923

61 Extra over the items SZ917 to SZ919 and SZ920 to SZ922for 15-amp 1-gang white plate switch socket-outlet pointcomplete with mounting box.

no $14.40 SZ924

of 69




Concealed Wiring In PVC Pipe Conduit (Cont'd)

20-Amp heater point complete with heater connectionunit and heater indication switch comprising of cablesdrawn through and including 20mm diameter PVCpipes cast/embedded in slab/wall complete with tees,connectors and other accessories:


no $91.80 SZ958


no $48.50 SZ959

C CIRCUIT WIRING

Earthing Conductors

Earth wiring including all fixings and connections(cable trunking/tray and conduits to be measuredseparately):-

64 25x3mm copper tape. m $17.00 SZ207

65 300mm² PVC earth cable. m $42.00 SZ949












of 69



C CIRCUIT WIRING(CONT'D)

Earthing Conductors (Cont'd)

Earth wiring including all fixings and connections(cable trunking/tray and conduits to be measuredseparately) (Cont'd):-



79 2.5mm² PVC earth cable. m $0.80 SZ725

80 1.5mm² PVC earth cable. m $0.70 SZ726

PVC/PVC cable

Circuit wiring including all fixings and connections(earthing conductors, cable trunking/tray and conduitsto be measured separately):

81 4x240mm² PVC/PVC cable. m $152.30 SZ319















of 69



C CIRCUIT WIRING (CONT'D)

PVC/PVC cable (Cont'd)

Circuit wiring including all fixings and connections(earthing conductors, cable trunking/tray and conduitsto be measured separately) (Cont'd):





100 2x2.5mm² PVC/PVC cable. m $2.80 SZ039

101 2x1.5mm² PVC/PVC cable. m $2.70 SZ040

PVC cable

Circuit wiring including drawing cables throughconcealed pipe conduits complete with all necessaryfixings and connections (conduits measuredseparately):

102 2x1.5mm² PVC cable & 1.5mm² PVC earth cable. m $2.40 SZ928

103 2x2.5mm² PVC cable & 2.5mm² PVC earth cable. m $2.80 SZ929

104 2x6mm² PVC cable & 6mm² PVC earth cable. m $4.70 SZ930

105 2x10mm² PVC cable & 10mm² PVC earth cable. m $6.70 SZ931


106 4x240mm² PVC cable. m $136.40 SZ306

107 4x185mm² PVC cable. m $103.70 SZ320

108 4x150mm² PVC cable. m $82.70 SZ307

109 4x120mm² PVC cable. m $69.00 SZ321

110 4x95mm² PVC cable. m $53.90 SZ322

111 4x70mm² PVC cable. m $39.30 SZ323

112 4x50mm² PVC cable. m $34.90 SZ702

of 69




PVC Cable (Cont'd)

113 4x35mm² PVC cable. m $27.60 SZ703

114 4x25mm² PVC cable. m $19.20 SZ308

115 4x16mm² PVC cable. m $12.60 SZ488

116 4x10mm² PVC cable. m $9.10 SZ309

117 2x50mm² PVC cable. m $17.90 SZ704

118 2x35mm² PVC cable. m $14.20 SZ705

119 2x25mm² PVC cable. m $10.00 SZ041

120 2x16mm² PVC cable. m $6.70 SZ042

121 2x10mm² PVC cable. m $5.00 SZ043

122 2x6mm² PVC cable. m $3.70 SZ044

123 2x4mm² PVC cable. m $3.00 SZ045

124 2x2.5mm² PVC cable. m $2.40 SZ046

125 2x1.5mm² PVC cable. m $2.10 SZ047

XLPE/PVC Cable


126 4x300mm² XLPE/PVC cable. m $204.40 SZ954







of 69




Fire resistant cable

Circuit wiring including all fixings and connections(earthing conductors, cable trunking/tray and conduitto be measured separately):

133 4x150mm² fire resistant cable. m $122.20 SZ706











144 2x10mm² fire resistant cable. m $10.50 Z0222



147 2x2.5mm² fire resistant cable. m $4.80 SZ301

148 2x1.5mm² fire resistant cable. m $4.40 SZ300

of 69




XLPE/SWA/PVC cable

XLPE/SWA/PVC underground armoured cable laid intrench (terminations and excavation of trench to bemeasured separately):

149 2.5mm² 2-core cable. m $4.70 SZ950

150 6mm² 2-core cable. m $6.70 SZ058

151 10mm² 2-core cable. m $10.20 SZ059

152 16mm² 2-core cable. m $12.10 SZ060

153 25mm² 2-core cable. m $16.50 SZ061

154 6mm² 3-core cable. m $8.80 SZ489

155 10mm² 3-core cable. m $11.70 SZ490

156 16mm² 3-core cable. m $15.80 SZ491

157 25mm² 3-core cable. m $21.90 SZ492

158 6mm² 4-core cable. m $10.70 SZ727

159 10mm² 4-core cable. m $13.30 SZ062

160 16mm² 4-core cable. m $19.40 SZ063

161 25mm² 4-core cable. m $27.30 SZ064

162 35mm² 4-core cable. m $35.40 SZ065

163 50mm² 4-core cable. m $45.40 SZ066

164 70mm² 4-core cable. m $69.30 SZ728

165 95mm² 4-core cable. m $87.80 SZ729

166 120mm² 4-core cable. m $111.50 SZ730

167 150mm² 4-core cable. m $133.90 SZ731

168 185mm² 4-core cable. m $163.10 SZ732

169 240mm² 4-core cable. m $211.80 SZ733

170 300mm² 4-core cable. m $253.90 SZ933

171 2.5mm² 12-core cable. m $16.90 SZ951

of 69




Terminations for XLPE/SWA/PVC cable includingsealing assembly and cable gland:

172 2.5mm² 2- core cable. no $8.10 Z0223

173 6mm² 2- core cable. no $10.90 SZ067




















of 69




Pipe Crossings/Cover Plates

UPVC pipes Class 'B' laid in trench for crossings(trench measured separately):

193 80mm diameter UPVC pipe. m $8.10 SZ081

194 100mm diameter UPVC pipe. m $15.60 SZ082

UPVC high impact resistant cable cover plates:

195 150mm wide x 2mm thick flat cable cover plate. m $4.70 SZ260

196 150mm wide x 2mm thick angled cable cover plate. m $4.70 SZ261

of 69



D CABLE SUPPORT SYSTEMS

PVC trunking

PVC trunking complete with accessories includingfixing to wall or ceiling:

197 60mm x 20mm three compartment. m $7.70 Z0224

198 80mm x 32mm twin compartment. m $8.90 SZ084

199 60mm x 20mm twin compartment. m $6.60 SZ085

200 40mm x 20mm single compartment. m $5.90 SZ086



203 25mm x 12.5mm single compartment. m $4.10 SZ089

Metal conduit

Galvanised steel conduit fixed to wall or ceilingcomplete with spacer bar saddles:

204 20mm diameter. m $18.30 SZ090

205 25mm diameter m $20.00 SZ091

206 32mm diameter. m $26.70 SZ092

207 20mm diameter inspection tee. no $3.40 SZ093

208 25mm diameter ditto. no $5.00 SZ094


210 20mm diameter inspection bend. no $2.60 SZ096



213 20mm diameter inspection elbow. no $3.30 SZ099



of 69



D CABLE SUPPORT SYSTEMS (CONT'D)

Metal conduit (Cont'd)

Galvanised steel conduit fixed to wall or ceilingcomplete with spacer bar saddles (Cont'd):

216 Circular through box with cover for 20mm diameter. no $2.70 SZ937

217 Circular T-junction box with cover for 20mm diameter. no $2.70 SZ944

PVC conduit

High impact PVC conduit fixed to wall or ceilingcomplete with spacer bar saddles:

218 20mm diameter. m $4.60 SZ102






224 Circular junction box with lid for 20mm diameter. no $3.60 SZ108

225 Ditto for 25mm diameter. no $3.70 SZ109

Flexible PVC conduit fixed to wall or ceiling completewith spacer bar saddles or suspension brackets, etc:



PVC concealed pipe conduit

PVC pipe conduit cast/embedded in slab/wall completewith tees, connectors and other accessories:




of 69



D CABLE SUPPORT SYSTEMS (CONT'D)

Metal trunking

Electro-galvanised/phosphate-dipped steel trunkingwith epoxy powder paint fixed to wall or ceilingcomplete with standard joint accessories and cover:

231 50mm x 50mm. m $12.50 SZ110

232 75mm x 75mm. m $14.80 SZ936

233 100mm x 50mm. m $15.00 SZ111

234 150mm x 50mm. m $18.00 SZ112

235 150mm x 75mm. m $19.10 SZ962

236 200mm x 50mm. m $21.70 SZ113

237 200mm x 100mm. m $24.30 SZ948

238 250mm x 50mm. m $24.40 SZ114

239 300mm x 50mm. m $27.50 SZ115

240 300mm x 75mm. m $29.00 SZ685

Cable tray

Hot-dipped galvanised hot rolled perforated mild steelcable trays fixed to wall or ceiling complete withhangers and fixing accessories:

241 100mm width. m $21.80 SZ116

242 150mm width. m $23.60 SZ117

243 225mm width. m $30.30 SZ118

244 300mm width. m $40.50 SZ119

245 450mm width. m $61.50 SZ120

246 600mm width. m $78.20 SZ121

of 69



E ELECTRICAL ACCESSORIES

Consumer control unit

Insulated consumer control unit complete with 63A DPisolator switch, 40A RCCB, DP 20KA DIN rail mountedplug-in surge protector and:

247 6x6A-20A 6KA MCB. no $217.30 Z0225

248 12x6A-30A 6KA MCB. no $252.50 Z0226

249 Insulated consumer control unit complete with 63A DPisolator switch, DP 20KA DIN rail mounted plug-in surgeprotector and 6x6A-20A 6KA MCB.

no $181.10 Z0227

250 Insulated consumer control unit complete with 40A/63ADP M6 MCB with contact position indicator, 40A/63ARCCB, DP 20KA DIN rail mounted plug-in surge protectorand 8x5A-32A 6KA MCB.

no $278.30 Z0228

Split load insulated consumer control unit completewith 40A/63A DP M6 MCB with contact positionindicator, 63A DP isolator, 40A/63A RCCB, DP 20KADIN rail mounted plug-in surge protector and:

251 9x6A-32A 6KA MCB. no $283.00 Z0229

252 10x6A-32A 6KA MCB. no $287.70 Z0230

253 12x6A-32A 6KA MCB. no $297.00 Z0231

Metal-clad consumer control unit complete with 63ADP isolator switch and 40A RCCB:

254 6x6A-20A 6KA MCB. no $188.00 SZ128

255 12x6A-30A 6KA MCB. no $284.60 SZ131

256 Metal-clad consumer control unit complete with 63A DPisolator switch and 6x6A-20A 6KA MCB.

no $167.30 SZ134

257 Split load metal-clad consumer control unit complete with63A DP isolator switch, 40A RCCB and 6x5A-20A 6KAMCB.

no $199.30 SZ136

of 69



E ELECTRICAL ACCESSORIES (CONT'D)

30mA trip RCCB complete with mounting box:

258 40A DP. no $110.80 SZ138

259 63A DP. no $138.30 SZ139

260 40A 4P. no $123.10 SZ503

261 63A 4P. no $167.90 SZ504

Switch fuse

Metal clad switch fuse complete with HRC fuse:

262 20A DP. no $85.00 SZ141

263 32A DP. no $113.80 SZ142

264 63A DP. no $250.80 SZ143

265 100A DP. no $370.20 SZ144

266 20A TPN. no $85.00 SZ145

267 32A TPN. no $113.80 SZ146

268 63A TPN. no $211.50 SZ147

269 100A TPN. no $370.20 SZ148

Miniature Circuit Breakers:

270 5A-20A SP 6KA. no $17.40 SZ140

271 40A DP M6. no $39.00 SZ466

272 63A DP M6. no $31.00 SZ324

of 69




Isolator switch

Metal clad isolator switch:

273 10A TPN. no $106.50 SZ282

274 32A TPN. no $121.50 SZ151

275 63A TPN. no $143.60 SZ152

276 100A TPN. no $303.30 SZ153

277 200A TPN. no $596.00 SZ967

Weatherproof PVC isolator switch:

278 10A TPN. no $39.70 SZ505

279 20A TPN. no $44.90 SZ953

280 32A TPN. no $54.90 SZ509

281 63A TPN. no $70.70 Z0184

282 100A TPN. no $420.30 Z0185

Switchgears

283 Electrical meter box size approximately 530 x 300 x180mm complete with all necessary ironmongery (otheraccessories measured separately).

no $308.70 SZ158

284 Lighting distribution board complete with 4x20A HRCfuse, 6KA 20A/30A MCB, contactor, time switch, bypassswitch.

no $1,122.10 SZ159

Moulded case circuit breaker (MCCB):

285 25KA 415V TP 15A-100A. no $181.20 SZ161

286 25KA 415V TP 125A-225A. no $342.60 SZ162

287 36KA 415V TP 125A-225A. no $388.80 SZ163

288 36KA 415V TP 250A-400A. no $552.60 SZ164

289 50KA 415V TP 450A-600A. no $1,186.70 SZ512

290 50KA 415V TP 700A-800A. no $1,493.20 SZ513

of 69




Switchboard's accessories

Contactor:

291 30A DP. no $73.90 SZ165

292 60A DP. no $216.80 SZ166

293 30A 4P. no $130.00 SZ167

294 60A 4P. no $281.80 SZ168

295 Ripple control receiver. no $402.70 Z0187

296 Time switch of programmable logic relay module completewith RS323C interface, built in timer and at least fouroutput points.

no $151.60 Z0242

297 Metal enclosure box overall size approximately200x320x130mm to house ripple control receiver.

no $41.30 SZ318

Main switchboard's accessories or instruments

298 Ammeter - current transformer operated (0 - 1600A). no $42.70 SZ262

299 Voltmeter - rotary wafer type (0 - 500V). no $45.00 SZ263

300 Ammeter or Voltmeter selector switch. no $22.00 SZ264

301 Maximum demand Ammeter. no $169.20 SZ265

302 Indicating light complete with built-in transformer. no $21.00 SZ266

303 Earth Fault Relay with built-in timer. no $173.80 SZ267

304 Hour Run Meter. no $100.20 SZ281

305 Earth Leakage Relay with built-in timer no $197.60 Z0186

306 Over-current Relay with built-in timer. no $298.00 SZ268

307 Over-current Relay of IDMTL (Inverse Definite MinimumTime Lag) with 3/10 characteristics.

no $1,893.80 SZ325

308 Digital Protection Relay for IDMTL and earth faultprotection, complete with measuring capability for ampere,voltage, maximum demand, frequency, etc. and remotemonitoring features.

no $2,888.60 Z0232

of 69




Protective Transformer:

309 CT ratio 100/5 (5P10, 20VA). no $238.20 SZ514

310 CT ratio 200/5 (5P10, 20VA). no $133.30 SZ269

311 CT ratio 300/5 (5P10, 20VA). no $119.40 SZ270

312 CT ratio 400/5 (5P10, 20VA). no $105.50 SZ271

313 CT ratio 600/5 (5P10, 20VA). no $86.20 SZ272

314 CT ratio 1200/5 (5P10, 20VA). no $103.20 SZ273

315 CT ratio 1600/5 (5P10, 20VA). no $100.80 SZ274

Metering Current Transformer:

316 CT ratio 100/5 (Class 15VA). no $42.20 SZ515







Connectors

BI Connector:

323 60A. no $7.20 SZ170

324 100A. no $7.20 SZ171

325 200A. no $41.70 SZ172

326 20A DP heater connection unit. no $12.50 SZ516

327 10A polarised plug and socket connector. no $4.00 SZ173

328 5A white moulded batten lamp holder. no $6.00 SZ174

329 5A white moulded ceiling rose. no $8.60 SZ175

of 69




Switches

6A White rocker plate switch complete with box forsurface mounting:

330 1-way 1-gang. no $12.10 SZ176

331 2-way 1-gang. no $13.10 SZ998

332 2-gang. no $15.00 SZ177

333 3-gang. no $19.30 SZ178

334 20A DP heater switch complete with box for surfacemounting.

no $24.40 SZ517

6A Ultra thin plate switch complete with box for flushmounting:

335 1-way 1-gang. no $17.40 SZ988

336 2-way 1-gang. no $16.10 SZ999

337 2-gang. no $24.90 SZ989

338 3-gang. no $36.80 SZ990

339 20A Ultra thin DP heater switch complete with box for flushmounting.

no $41.80 SZ992

340 White rocker plate bell push complete. no $13.90 SZ518

6A metal clad rocker switch complete with mountingbox:

341 1-way 1-gang. no $19.60 Z0218

342 2-way 1-gang no $20.80 SZ180

343 2-gang. no $23.00 SZ181

344 3-gang. no $29.00 SZ182

of 69




Switch socket outlets

Plate switch socket outlet complete with box forsurface mounting:

345 13A 1-gang. no $12.50 SZ184

346 13A 2-gang. no $18.10 SZ185

347 15A 1-gang. no $19.70 SZ188

Ultra thin switch socket outlet complete with box forflush mounting:

348 13A 1-gang. no $18.90 SZ985

349 13A 2-gang. no $28.40 SZ986

350 15A 1-gang. no $33.30 SZ987

Metal clad switch socket outlet complete withmounting box:

351 13A 1-gang. no $19.40 SZ186

352 13A 2-gang. no $28.30 SZ187

353 15A 1-gang. no $25.70 SZ189

PVC weatherproof switch socket outlet complete withscrew cap:

354 13A. no $41.30 SZ190

355 15A. no $70.10 SZ191

Metal type weatherproof switch socket outlet completewith screw cap:

356 13A. no $51.10 SZ520

357 15A. no $79.10 SZ521

358 Metal enclosure size 210x180x140mm to house switchsocket outlet complete with hinged door and cam lock.

no $18.70 SZ194

of 69



F LUMINAIRES

359 Woolite WWLC 141/EB/WWT complete with T5 1x14Wlamp and high frequency electronic ballast.

no $53.70 Z1101


no $54.90 Z1102


no $66.40 Z1103

362 Hugo-F.141.FMR-T5 complete with T5 1x14W lamp, heavygauge electro-galvanised steel base, aluminium reflectorand high frequency electronic ballast.

no $70.40 Z1104

363 Davis EL114T5 complete with T5 1x14W lamp and highfrequency electronic ballast.

no $43.40 Z1105

364 Davis EL128T5 complete with T5 1x28W lamp and highfrequency electronic ballast.

no $45.70 Z1106

365 Simlite BSS 114 complete with T5 1x14W lamp, powdercoated reflector and high frequency ballast.

no $80.20 Z1107

366 Simlite BSS 214 complete with T5 2x14W lamp, powdercoated reflector and high frequency ballast.

no $91.70 Z1108

367 Similite BSS 128 complete with T5 1x28W lamp, powdercoated reflector and high frequency ballast.

no $91.70 Z1109

368 Similite SB 114 complete with T5 1x14W lamp and highfrequency ballast.

no $53.70 Z1110

369 Simlite SB 128 complete with T5 1x28W lamp and highfrequency ballast.

no $57.20 Z1111

370 Basic CL1 complete with T5 1x14W lamp, epoxy polyesterpowder coated metallic body and gear.

no $73.30 Z1112

371 Basic CL1 complete with 1x28W T5 lamp, epoxy polyesterpowder coated metallic body and gear.

no $82.50 Z1113

of 69



F LUMINAIRES (CONT'D)

372 Thorn Formula 1F1XZ114R complete with T5 1x14W lamp,cold roll steel powder coated housing, aluminium reflectorand high frequency ballast.

no $99.70 Z1115

373 Aztech LF212 LED luminaire complete with 12W LEDlamp.

no $82.50 Z1116

374 Aztech LF212S LED luminaire complete with 12W LEDlamp and motion sensor.

no $114.70 Z1117

375 Aztech LF212B LED luminaire complete with 12W LEDlamp and backup battery.

no $151.50 Z1118

376 Aztech LF212BS LED luminaire complete with 12W LEDlamp, motion sensor and backup battery.

no $174.50 Z1119

377 Aztech LF424 LED luminaire complete with 24W LEDlamp.

no $157.20 Z1120

378 Aztech LF424S LED luminaire complete with 24W LEDlamp and motion sensor.

no $180.20 Z1121

379 Aztech LF424B LED luminaire complete with 24W LEDlamp and backup battery.

no $280.30 Z1122

380 Aztech LF424BS LED luminaire complete with 24W LEDlamp, motion sensor and backup battery.

no $306.70 Z1123

381 DAVIS-OPTILED-228 2 feet LED luminaire complete with9W LED lamp.

no $94.00 Z1124

382 DAVIS-OPTILED-228M 2 feet LED luminaire complete with9W LED lamp and motion sensor.

no $117.00 Z1125

383 DAVIS-OPTILED-228E 2 feet LED luminaire complete with9W LED lamp and backup battery

no $186.00 Z1126

384 DAVIS-OPTILED-228ME 2 feet LED luminaire completewith 9W LED lamp, motion sensor and backup battery

no $209.00 Z1127

G LIGHTNING CONDUCTORS AND EARTH RODS

385 Aluminium 25mm x 3mm tape with aluminium clip andbase properly secured onto wall or roof for lightningconductors.

m $5.20 SZ205

386 Copper 25mm x 3mm tape with brass/bronze clip andbase properly secured onto wall or roof for lightningconductors.

m $17.00 SZ207

of 69



G LIGHTNING CONDUCTORS AND EARTH RODS (CONT'D)

387 50mm² stranded bare copper conductors withbrass/bronze clip and base properly secured onto wall orroof for lightning conductors.

m $15.00 SZ208

388 70mm² stranded bare copper conductors withbrass/bronze clip and base properly secured onto wall orroof for lightning conductors.

m $16.90 SZ209

389 Air terminal 16mm diameter 300mm length aluminiumcomplete with cast aluminium alloy base.

no $20.40 SZ210

390 Air terminal 16mm diameter 300mm length coppercomplete with leaded gunmetal base.

no $29.30 SZ211

391 Bi-metallic aluminium-copper connector for 25mm x 3mmtape.

no $21.50 SZ212

392 Aluminium square tape clamp suitable for 25 x 3mm tape. no $12.40 SZ213

393 Copper square tape clamp suitable for 25 x 3mm tape. no $14.60 SZ968

394 Leaded gunmetal square tape clamp suitable for 25mm x3mm tape.

no $17.80 SZ214

395 Leaded gunmetal round test clamp. no $27.40 SZ215

396 Leaded gunmetal 'B' bond for bonding copper tape tosteel surface.

no $14.80 SZ216

397 Aluminium 'B' bond for bonding aluminium tape to steelsurface.

no $13.40 SZ217

398 Exothermic welded joint. no $31.90 SZ218

399 Earth rod 16mm diameter 1.8m long copper-weld, mildsteel rod driven in ground.

no $37.30 SZ221

400 Interconnecting buried 25mm x 3mm copper tape. m $13.40 SZ222

401 Leaded gunmetal/naval brass earth rod clamp. no $17.10 SZ223

402 Aluminium/silicon/phosphor bronze earth rod coupling. no $7.00 SZ224

403 Clamp for earthing and bonding to pipe diameter 12mm -75mm.

no $2.80 SZ225

404 250mm x 250mm x 3mm thick hot-dipped hinged-lidinspection pit complete with plastic moulded pot.

no $25.60 SZ226

of 69



H EXTERNAL LIGHTING

Lighting Columns

Hot dipped galvanised planted type lighting columnincluding excavation of pit, concrete footing, bitumencoating of planted section, painting of identificationnumbers, cutout complete with 5A-20A HRC fuse,connecting accessories, (but excluding cable glands)and backfilling and reinstatement of ground surfacesas detailed in the drawings:

405 8m lighting column with single arm bracket. no $738.80 SZ227

406 10m lighting column with double arm bracket. no $842.40 Z0165

407 3m post top lighting column. no $376.30 SZ230

408 3.5m post top lighting column. no $402.40 SZ932


410 4.5m post top lighting column. no $448.40 Z0164





Hot dipped galvanised flanged mounted type lightingcolumn including painting of identification numbers,cutout complete with 5A-20A HRC fuse and connectingaccessories (but excluding cable glands) as detailed inthe drawings :

415 3m post top lighting column. no $404.20 Z0166





of 69



H EXTERNAL LIGHTING (CONT'D)

Accessories for lighting columns

420 Pole cap. no $58.30 Z0171

421 Banner bracket. no $75.50 Z0172

422 Centre ring 90mm diameter (OD). no $46.80 Z0173

423 Shoulder cover (Type 1) 76mm / 140mm diameter. no $115.80 Z0174

424 Shoulder cover (Type 1A) 100mm / 140mm diameter. no $121.50 Z0175

425 Shoulder cover (Type 2) 76mm / 140mm diameter. no $92.80 Z0176

426 Shoulder cover (Type 2A) 100mm / 140mm diameter. no $98.50 Z0177

Painting of lighting columns

One coat of lead and chromate free primer and twocoats of polyurethene paint on the external surfaceof lighting column:

427 3m-3.5m high column. no $9.90 Z0235

428 4m high column. no $11.80 Z0236

429 4.5m high column. no $13.00 Z0237




433 10m high column. no $33.20 Z0241

Polyester powder coating in standard RAL colour ontothe external surface of lighting column including allnecessary labour & transport.


435 3.5m high column. no $92.00 Z0179

436 4m high column. no $104.30 Z0180

437 4.5m high column. no $110.50 Z0181

438 5m high column. no $116.70 Z0182

of 69




Polyester powder coating in standard RAL colour ontothe external surface of lighting column including allnecessary labour & transport.(Cont'd)

439 6m high column. no $129.00 Z0183

440 8m high column. no $134.60 Z0212

441 10m high column. no $146.90 Z0213

Service Road & Driveway Luminaire

Lighting luminaires complete with integral controlgears and other accessories:

442 3E post-top luminaire Cobra FDL-D2/VP/VB/VM/VGcomplete with clear/pearl/opal methacrylate diffuser,80W/125W mercury super deluxe lamp, separate ignitorand single arm mounting bracket.

no $1,382.90 Z0031

443 3E post-top luminaire Cobra FDL-D2-VP/VB/VM/VGcomplete with clear/pearl/opal methacrylate diffuser, 70WSON lamp, separate ignitor and single arm mountingbracket.

no $1,382.90 Z0030

444 3E post–top luminaire Harmony FDL-DD2-VM, in die castaluminium body with upperdome in aluminium material,methacrylate diffuser, part polished and anodisedaluminium reflector complete with 70W SON lamp andsingle arm bracket.

no $813.70 Z0189

445 3E post-top luminaire Hirondelle FDS-D2-VM/VB/VP/VGcomplete with clear/pearl/opal methacrylate diffuser, 70WSON lamp and separate ignitor.

no $1,388.70 Z0024

446 3E post-top luminaire Hirondelle FDS-D2-VM/VB/VP/VGcomplete with clear/pearl/opal methacrylate diffuser,80W/125W mercury super deluxe lamp, separate ignitorand single arm mounting bracket.

no $1,359.90 Z0025

447 3E post-top luminaire Libellule FDL-D2/D*-VB/VP/VM/VGcomplete with clear/pearl/opal methacrylate diffuser, 70WSON lamp, separate ignitor, and single arm mountingbracket.

no $1,497.90 Z0028

448 3E post-top luminaire Libellule FDL-D2/D*-VB/VP/VM/VGcomplete with clear/pearl/opal methacrylate diffuser,80W/125W mercury super deluxe lamp, separate ignitorand single arm mounting bracket.

no $1,469.20 Z0029

of 69




Service Road & Driveway Luminaire (Cont'd)

Lighting luminaires complete with integral controlgears and other accessories (Cont'd):

449 3E post-top luminaire Sygma FD-D2-VB/VP/VM/VGcomplete with clear/pearl/opal methacrylate diffuser, 70WSON lamp, separate ignitor and single arm mountingbracket.

no $1,394.40 Z0026

450 3E post-top luminaire Sygma FD-D2-VB/VP/VM/VGcomplete with clear/pearl/opal methacrylate diffuser,80W/125W mercury super deluxe lamp, separate ignitorand single arm mounting bracket.

no $1,365.70 Z0027

451 A+G post-top luminaire ZOB 1060 complete withpolycarbonate diffuser and 70W SON MBFSD lamp.

no $2,067.20 Z0032

452 AEG post-top luminaire Triangel Type-A1 complete with70W SON lamp, clear safety glass diffuser.

no $1,114.40 Z0014

453 AEG post-top luminaire Triangel Type-A1 complete with80/125W MBFSD lamp, clear safety glass diffuser.

no $1,084.00 Z0015

454 ALCATEL post-top luminaire FG Cutoff/CL complete with70W SON lamp, clear polycarbonate diffuser.

no $519.90 Z0016

455 ATP post-top luminaire Alameda Vial complete with 70WSON/80W or 125W super deluxe mercury, body frame incorrosion-resistant glass reinforced polymer and clear/opalUV-stabilised polycarbonate diffuser.

no $1,112.70 Z0001

456 ATP post-top luminaire Europa Vial complete with 70WSON/80W or 125W super deluxe mercury, body frame incorrosion-resistant glass reinforced polymer and clear/opalUV-stabilised polycarbonate diffuser.

no $874.10 Z0002

457 BEGA post-top luminaire Cat No. 8141 surface washerscomplete with 70W SON lamp.

no $1,101.80 Z0045

458 D.W. WINDSOR post-top luminaire DOVER complete withdie-cast aluminium ring, illuminated top canopy, clearpolycarbonate glazing, diamond optic variable reflectorsystem and 70W SON or 125W MBFSD lamp.

no $1,285.20 Z0038

459 D.W. WINDSOR post-top luminaire HATFIELD completewith spun aluminium canopy, clear diffuser, diamond opticvariable reflector system and 1 x 70W SON or 125WMBFSD lamp.

no $1,285.20 Z0040

of 69






460 D.W. WINDSOR post-top luminaire YORK HENLYcomplete with die-cast aluminium base, spun aluminiumcanopy, clear or reeded polycarbonate diffuser, base conereflector, diamond optic variable reflector system and 1 x70W SON or 125W MBFSD lamp.

no $1,285.20 Z0039

461 HELUX post-top luminaire Hellux 115 complete with 70Whigh pressure sodium lamp or 80W/125W mercury superdeluxe lamp and acrylic diffuser.

no $1,588.80 Z0037

462 IDMAN post-top luminaire OCULUS 70674 with high purityanodized aluminium reflector and bowl of impact-resistantacrylic resin diffuser complete with 70W SON lamp andsingle arm bracket.

no $880.40 Z0192

463 KL LICHT post-top luminaire Modul 6113 complete with70W SON/80W or 125W super deluxe mercury, bodyframe in cast aluminium and clear, frosted or opal UV-stabilised polycarbonate diffuser.

no $2,124.70 Z0003

464 RAGNI arm mounted luminaire ORIGIA 6600 of embossedaluminium dome and body of cast aluminium constructioncomplete with 1 x 70W SON lamp, anti-glare pure polishaluminium reflector, clear tempered glass diffuser anddecorative single arm bracket of HDG steel arm typeConsole Dalia or Console Cecia.

no $613.50 Z0188

of 69






465 STERNER post-top luminaire FRANKLIN III complete withaluminium extrusion construction complete with powdercoat finish, clear lens, Type II horizontal performancereflector, straight arm and 1 x 70W SON or 125W MBFSDlamp.

no $1,147.20 Z0041

466 STERNER post-top luminaire MANCHESTER completewith aluminium extrusion construction complete withpowder coat finish, clear lens, IES Type II performancereflector, straight arm and 1 x 70W SON or 125W MBFSDlamp.

no $1,325.40 Z0042

467 STERNER post-top luminaire MARQUETTE complete withaluminium extrusion construction complete with powdercoat finish, clear lens, IES Type II performance reflector,straight arm and 1 x 70W SON or 125W MBFSD lamp.

no $1,325.40 Z0043

468 WE-EF area light luminaire SBL440-E-50/70/NI(K)complete with corrosion resistant aluminium alloy body,thermal shock resistant safety glass in a hinged aluminiumframe and stainless steel fasteners, anodized high puritychemically brightened aluminium reflector and Electronic65W lamp/60W GE lamp and KS1.76 adapter and finish inRAL polyester powder coat.

no $636.00 Z0012

469 WE-EF area light luminaire SBL440-E9-80/125(K)complete with corrosion resistant aluminium alloy body,thermal shock resistant safety glass in a hinged aluminiumframe and stainless steel fasteners, anodized high puritychemically brightened aluminium reflector and Electronic65W lamp/60W GE lamp and KS1.76 adapter and finish inRAL polyester powder coat.

no $624.60 Z0013

of 69






470 WE-EF post-top luminaire BSP504-E-50/70/NI(K) completewith corrosion resistant die-cast aluminium alloy body andcanopy, UV stablized and vandal resistant polycarbonatediffuser, anodized high purity aluminium reflector andElectronic 65W lamp/60W GE lamp and BA1/420.76bracket and finish in RAL polyester powder coat.

no $1,464.50 Z0008

471 WE-EF post-top luminaire BSP504-E-80/125(K) completewith corrosion resistant aluminium alloy body and canopy,UV stablized and vandal resistant polycarbonate diffuser,anodized high purity aluminium reflector and Electronic65W lamp/60W GE lamp and BA1/420.76 bracket andfinish in RAL polyester powder coat.

no $1,459.40 Z0009

472 WE-EF post-top luminaire BSP704-E-50/70/NI(K) completewith corrosion resistant aluminium alloy body and canopy,UV stablized and vandal resistant polycarbonate diffuser,anodized high purity aluminium reflector and Electronic65W lamp/60W GE lamp and BA1/580.76 bracket andfinish in RAL polyester powder coat.

no $1,980.00 Z0010

473 WE-EF post-top luminaire BSP704-E-80/125(K) completewith corrosion resistant aluminium alloy body and canopy,UV stablized and vandal resistant polycarbonate diffuser,anodized high purity aluminium reflector and Electronic65W lamp/60W GE lamp and BA1/580.76 bracket andfinish in RAL polyester powder coat.

no $1,969.10 Z0011

474 WE-EF post-top luminaire CA504-E-50/70/NI(K) completewith corrosion resistant aluminium alloy body,polycarbonate diffuser and vandal resistant, anodized highpurity aluminium reflector, chemically brightened, completewith Electronic 65W lamp/60W GE lamp and KC1.76adapter and finish in RAL polyester powder coat.

no $1,256.40 Z0007

of 69






475 WE-EF post-top luminaire CA504-E-80/125(K) completewith corrosion resistant aluminium alloy body,polycarbonate diffuser and vandal resistant, anodized highpurity aluminium reflector, chemically brightened, completewith Electronic 65W lamp/60W GE lamp and KC1.76adapter and finish in RAL polyester powder coat.

no $1,233.40 Z0006

476 3E decorative post-top luminaire DELTA complete with 1 x70W SON lamp, die-cast aluminium body with flattoughened glass diffuser and asymmetrical aluminiumreflector with DELTA single arm mounting bracket(1200mm projection).

no $729.20 Z1004

477 LIGMAN 96033 post-mounted luminaire complete with 1 x70W SON lamp, high corrosion resistant aluminium alloybody with matt black powder coating, clear toughen glassdiffuser, asymmetrical anodised high purity aluminiumreflector, bracket and mounting accessories.

no $894.20 Z1005

478 EYE H5908 decorative semi-hemisphere streetlight widedistribution post-mounted luminaire complete with 1 x 70WSON lamp, die-cast aluminium baked acrylic paint finishbody, heat tempered glass diffuser, asymmetricalaluminium reflector, HEA-15 bracket and mountingaccessories.

no $813.70 Z1027

479 MEYERLUX 2304 decorative post-top luminaire completewith 1 x 70W ceramic metal halide lamp, die-castaluminium body with black powder coating paint, cleartempered glass diffuser, asymmetrical light distributionspecular anodised aluminium reflector, bracket andmounting accessories.

no $724.00 Z1030

of 69






480 DW WINDSOR decorative post-top luminaire AKORDCONE complete with 1 x 70W SON lamp, die-castaluminium body with flat toughened glass diffuser, diamondoptic reflector with DA or CA or SB single arm mountingbracket.

no $894.20 Z1035

481 LIGMAN 97031 MARS streetlighting luminaire completewith 1 x 70W SON lamp, die-cast aluminium alloy body,tempered glass diffuser, asymmetrical aluminium reflector,pole spigot, bracket and mounting accessories.

no $723.50 Z1044

482 PRISMA OLA decorative post-top luminaire complete with1 x 70W SON lamp, die-cast non corroding aluminiumbody with powder coating finish, tempered glass diffuser,anodised aluminium reflector and mounting bracket (for60mm or 90 mm pole).

no $802.20 Z1047

483 Philips Street Lantern SPP202/070 post-top luminairecomplete with 1 x 70W SON lamp, die-cast aluminiumhousing, high purity anodized aluminium facetted reflector,curved tempered glass diffuser, bracket and mountingaccessories.

no $307.70 Z1052

484 GGE 858-DG0302 post-mounted luminaire complete with 1x 70W SON lamp, die-cast aluminium body, cleartempered glass diffuser, asymmetrical anodised aluminiumreflector, bracket and mounting accessories.

no $698.70 Z1058

485 THORN CIVIC 1, CIVFGP70.4 post-top luminaire completewith 1 x 70W SON lamp, die-cast aluminium body, flattoughened glass diffuser and asymmetrical aluminiumreflector.

no $336.40 Z1062

of 69




Landscape & Playground Lighting Luminaire


486 AAL SL VT LARGENT post-top luminaire of one piece castaluminium construction for the body complete with frosteddiffuser, powder coat finish, performance reflector forcontrolled driveway or landscape lighting and 65W energylamp.

no $997.70 Z0088

487 BEGA post-top luminaire 8081 complete with symmetricallight distribution 80W/125W MBFSD lamp.

no $1,339.60 Z0065

488 BEGA post-top luminaire 8180 complete with symmetricallight distribution 70W SON lamp.

no $1,424.30 Z0066

489 CLING CASTALDI post-top luminaire Cat No. Veneziacomplete with 125W mercury super deluxe lamp, anti UVunbreakable opal top polycarbonate diffuser and clearbottom UV-stabilised polycarbonate diffuser, downwardsemission in symmetrical reflector.

no $1,240.90 Z0197

490 D.W. WINDSOR post-top luminaire YORK BRAMARcomplete with die-cast aluminium base, spun aluminiumcanopy, clear or reeded polycarbonate diffuser, base conereflector, diamond optic variable reflector system and 70WSON/125W MBFSD lamp.

no $1,285.20 Z0081

491 D.W. WINDSOR post-top luminaire YORK NEWPORTcomplete with die-cast aluminium base, spun aluminiumcanopy, clear or reeded polycarbonate diffuser, base conereflector, diamond optic variable reflector system and 70WSON/125W MBFSD lamp.

no $1,285.20 Z0080

492 D.W. WINDSOR post-top luminaire YORK WATERFORDcomplete with die-cast aluminium base, spun aluminiumcanopy, clear or reeded polycarbonate diffuser, base conereflector, diamond optic variable reflector system and 70WSON/125W MBFSD lamp.

no $1,285.20 Z0082

493 ELTE post-top luminaire Chinese Hat I 6710 complete with70W SON/80W or 125W super deluxe mercury, fixture incorrosion free aluminium with inner optical louvred reflectorbuilt in cyclindrical clear, frosted or opal UV-stabilizedpolycarbonate diffuser.

no $1,972.90 Z0048

494 ELTE post-top luminaire Chinese Hat I 6711 complete with70W SON/80W or 125W super deluxe mercury, fixture incorrosion free aluminium with lamellas arranged outsidecyclindrical clear, frosted or opal UV-stabilizedpolycarbonate diffuser.

no $2,147.70 Z0049

of 69




Landscape & Playground Lighting Luminaire (Cont'd)


495 EWO post-top luminaire UL00-000-M with clear/sandblasted PMMA diffuser complete with 70W SON/125Wmercury super deluxe lamp.

no $1,032.20 Z0199

496 HELLUX post-top luminaire Hellux 034 complete with 70Whigh pressure sodium lamp or 80W/125W mercury superdeluxe lamp and acrylic diffuser.

no $1,221.90 Z0072

497 HELLUX post-top luminaire Hellux 035 complete with 70Whigh pressure sodium lamp or 80W/125W mercury superdeluxe lamp and acrylic diffuser.

no $1,266.20 Z0073

498 HELLUX post-top luminaire Hellux 401-4 complete with70W high pressure sodium lamp or 80W/125W mercurysuper deluxe lamp and acrylic diffuser.

no $880.40 Z0074

499 HOFFMEISTER post-top luminaire Baskette cat no1.2273.1.49.721 of cast aluminium housing, silver anodizedaluminium lamellar reflector and clear acrylic diffusercomplete with 1 x 125W mercury super deluxe lamp .

no $2,105.10 Z0057

500 HOFFMEISTER post-top luminaire Baskette cat no1.2273.3.57.721 of cast aluminium housing, silver anodizedaluminium lamellar reflector and clear acrylic diffusercomplete with 1 x 70W SON lamp.

no $2,222.40 Z0058

501 HOFFMEISTER post-top luminaire Baskette cat no122735557721 of cast aluminium housing, silver anodizedaluminium louvred reflector and clear acrylic diffusercomplete with 1 x 70W SON lamp.

no $1,940.70 Z0059

of 69






502 HOFFMEISTER post-top luminaire Baskette cat no1.2280.1.49.721 of cast aluminium housing, silver anodizedaluminium reflector and clear acrylic diffuser complete with1 x 125W mercury super deluxe lamp.

no $1,679.60 Z0055

503 HOFFMEISTER post-top luminaire Baskette cat no1.2280.3.57.721 of cast aluminium housing, silver anodizedaluminium reflector and clear acrylic diffuser complete with1 x 70W SON lamp.

no $1,775.10 Z0056

504 IEP decorative post top lantern RANGE F05 of body, frameand top cover plate in cast aluminium complete with opalor clear methacrylate diffuser and 65W energy lamp.

no $485.90 Z0195

505 KL LICHT post-top luminaire Modul 6110 complete with70W SON/80W or 125W super deluxe mercury, body incast aluminium and clear, frosted or opal UV-stabilizedpolycarbonate diffuser.

no $1,630.20 Z0050

506 KL LICHT post-top luminaire Trapez 5017 complete with70W SON/80W or 125W super deluxe mercury, body incast aluminium and frosted UV-stabilized polycarbonatediffuser.

no $1,271.40 Z0051

507 KL LICHT post-top luminaire Trapez 5082 complete with70W SON/80W or 125W super deluxe mercury, body incast aluminium and frosted UV-stabilized polycarbonatediffuser.

no $1,842.90 Z0052

508 KL LICHT post-top luminaire Zylinder-Quadro 1716.125complete with 70W SON/80W or 125W super deluxemercury, body and top cover in cast aluminium andcylindrical opal UV-stabilized polycarbonate diffuser.

no $2,067.20 Z0053

of 69






509 KL LICHT post-top luminaire Zylinder-Quadro 1718.125complete with 70W SON/80W or 125W super deluxemercury, body and top cover in cast aluminium and anti-glare louvres built in cylindrical clear UV-stabilizedpolycarbonate diffuser.

no $2,147.70 Z0054

510 LOUIS POULSEN post-top luminaire KIPP 5747 298 811complete with 125W mercury super deluxe lamp.

no $1,641.70 Z0084

511 LOUIS POULSEN post-top luminaire KIPP 5747 298 811complete with 70W high pressure sodium lamp.

no $1,515.20 Z0085

512 LOUIS POULSEN post-top luminaire KIPP 5747 298 811complete with 80W mercury super deluxe lamp.

no $1,515.20 Z0083

513 ROGER PRADIER post-top luminaire PV4 complete withbody of aluminium with special treatment against corrosion,opal or smoked makrolon diffuser and 125W MBFSD lamp.

no $1,066.70 Z0086

514 ROGER PRADIER post-top luminaire PV4 complete withbody of aluminium with special treatment against corrosion,opal or smoked makrolon diffuser and 70W SON lamp.

no $1,124.20 Z0087

of 69






515 SIEMENS post-top luminaire Citylight Classic completewith sturdy glass enclosures, cast iron post-top sectioncover by an elegant plastic flange shape collar 70WSON/125W MBFSD lamp.

no $1,441.60 Z0063

516 SIEMENS post-top luminaire Citylight Elegance completewith sturdy glass enclosures, cast iron post-top sectioncover by an elegant plastic flange shape collar completewith 70W SON/125W MBFSD lamp.

no $1,466.90 Z0064

517 SIEMENS post-top luminaire Citylight Plus cat no 5NA-5262-1C of die-cast cast aluminium housing, pagodaspecular reflector system and acrylic diffuser complete with1 x 125 mercury super deluxe lamp.

no $1,004.60 Z0061

518 SIEMENS post-top luminaire Citylight Plus cat no 5NA-5262-1M of die-cast cast aluminium housing, pagodaspecular reflector system and acrylic diffuser complete with1 x 70W SON lamp.

no $1,039.10 Z0062

519 no $1,604.90 Z0069WE-EF post-top luminaire 01.ALY359-DT-18(I) completewith corrosion resistant aluminium alloy body, bracket andpost, polycarbonate UV stabilized and vandal resistantdiffuser and Electronic 20W lamp and finish in RALpolyester powder coat including 2.5m galvanised post toplighting column.

of 69






520 no $1,616.40 Z0070

521 WE-EF post-top luminaire ZA640-E-50/70/N(K) completewith corrosion resistant die-cast aluminium alloy body andcanopy, UV stabilized and vandal resistant polycarbonatediffuser and anodized high purity aluminium reflector andElectronic 65W lamp finished in RAL polyester powdercoat.

no $1,448.50 Z0067

522 WE-EF post-top luminaire ZA640-E-80/125W(K) completewith corrosion resistant die-cast aluminium alloy body andcanopy, UV stabilized and vandal resistant polycarbonatediffuser and anodized high purity aluminium reflector andElectronic 65W lamp finished in RAL polyester powdercoat.

no $1,438.10 Z0068

523 ROGER PRADIER PV4 antique lantern complete with 1 x125W mercury super deluxe lamp, die-cast corrosionresistant aluminium with powder coating body, translucentPMMA bowl diffuser, and aluminium reflector.

no $1,032.20 Z1006

524 ROGER PRADIER PV4 antique lantern complete with 1 x70W SON lamp, die-cast corrosion resistant aluminiumwith powder coating body, translucent PMMA bowl diffuser,and aluminium reflector.

no $1,043.70 Z1007

525 SIMLITE INOVA GE609D post-top luminaire complete with1 x 70W SON lamp or 125W mercury super deluxe lamp,die-cast aluminium alloy with powder coating bodycomponents, translucent PMMA diffuser and anti-glaresymmetric louver in aluminium reflector.

no $802.20 Z1032

WE-EF post-top luminaire 01.ALY359-DT-26(I) completewith corrosion resistant aluminium alloy body, bracket andpost, polycarbonate UV stabilized and vandal resistantdiffuser and Electronic 20W lamp and finish in RALpolyester powder coat including 2.5m galvanised post toplighting column.

of 69





Lighting luminaires complete with integral control gear, stainless steel screws and other accessories:

526 DW WINDSOR CRADLE 450 post-top luminaire completewith 1 x 70W SON lamp or 125W mercury super deluxelamp, die-cast aluminium with powder coating body, UVstabilised acrylic glazing, aluminium diamond optic reflectorand post-top mounting bracket.

no $802.20 Z1036

527 UNILAMP OD-7201 decorative post-top luminaire completewith 1 x 70W SON lamp or 125W mercury super deluxelamp, die-cast aluminium alloy with powder coating bodycomponents, vandal proof UV stabilized polycarbonatediffuser and anodized pure aluminium louvre reflector.

no $524.20 Z1045

528 AEC EVOLUTA decorative post-top luminaire (comply toUNI 10819 to limit upward lighting emission) complete with1 x 70W SON lamp or 125W mercury super deluxe lamp,die-cast aluminium (UNI 5076 conformity) with powdercoating body components, PMMA methacrylate diffuserand anodized pure aluminium louvre reflector.

no $474.40 Z1048

529 SITECO 5NA 5242-1CR28 post-top luminaire completewith 1 x 80W / 125W mercury super deluxe lamp, die-castaluminium with powder coating body components, clear UVstabilised PMMA methacrylate diffuser, and aluminiumsymmetrical or asymmetrical reflector.

no $618.20 Z1056

530 HELLUX QMB 417 post-top luminaire complete with 1 x70W SON lamp or 125W mercury super deluxe lamp, die-cast aluminium with powder coating body components, UVstabilised polycarbonate diffuser and ring louvre.

no $856.20 Z1057

531 THORN AVENUE F post-top luminaire complete with 1 x70W SON lamp or 125W mercury super deluxe lamp,aluminium powder coated anthracite textured body, opal orclear (with sandblasted frosted ring) UV stabilisedpolycarbonate diffuser, and aluminium symmetrical orasymmetrical reflector.

no $681.40 Z1063

532 LEO LO-L6209 floodlight complete with 1 x 250W / 400Wmetal halid lamp, specially designed reflector with deep-seated lamp, chemically treated aluminium alloy housingand finish with matt black powder coating, anodised highpurity aluminium reflector, durable silicon rubber gasketand clear toughen glass on hinged frame.

no $848.20 Z1012

of 69



I EXTERNAL LIGHTING (CONT'D)


Lighting luminaires complete with integral controlgear, stainless steel screws and other accessories:

533 VINIC 50601 post-top luminaire complete with 250W metalhalide lamp, die-cast aluminium housing, asymmetricalanodised high purity aluminium reflector and 5 mm thickclear tampered glass lens. IP 54.

no $825.20 Z1013

534 GP LICHT GP-8770 post-top luminaire complete with 55Wamalgam lamp, GP-155/HPF invertor, die-cast aluminiumbody, UV stabilised and impact resistant polycarbonatediffuser, 3 lines vertical prism symmetrical distributionm,pure anodised aluminium reflector, and mountingaccessories.

no $375.20 Z1100

535 EYE GALAXY FL42/LE/MT250DL rectangular shape die-cast aluminium floodlight complete with 1 x 250W metalhalid lamp, asymmetrical hammered finish reflector,tempered glass diffuser and mounting accessories.

no $433.20 Z1028

540 IGUZZINI B426 + B450 Lavinia asymmetrical optical poletop luminaire complete with70W metal halide lamp, purealuminium reflector, PMMA diffuser, die cast aluminiumoptical assembly and frame, with dual phosphorus-chronium plating base metal and protruding single-projector pole top, attachment 102mm.

no $1,078.20 Z1130

541 IGUZZINI B413 + B450 Lavinia asymmetrical optical poletop luminaire complete with70W metal halide lamp, purealuminium reflector, PMMA diffuser, die cast aluminiumoptical assembly and frame, with dual phosphorus-chronium plating base metal and protruding single-projector pole top, attachment 102mm.

no $1,078.20 Z1131

of 69






542 GE EUROFLOOD floodlight complete with 1 x 250W /400W metal halid lamp, HPF-Reactor ballast, polymerthermoplastic housing, anodized and polished aluminiumreflector with asymmetrical optics and clear thermal shockresistant glass diffuser.

no $312.50 Z1029

543 DISANO Art No. 1149 floodlight complete with 1 x 250Wmetal halid lamp, die-cast aluminium housing and framewith wide cooling fins, asymmetric optics in anodisedpolished hammered 99.85% aluminium reflector, 5mm thickthermal shock and impact resistant protective temperedglass diffuser and mounting accessories.

no $450.50 Z1031

544 DISANO INDIO 1159 floodlight complete with 250W metalhalide lamp, die-cast aluminium housing and frame,asymmetric optics in anodized polished hammered 99.85%aluminium, 5 mm thick thermal shock and impact resistantprotective tempered glass diffuser and local made Tbracket. IP 65.

no $393.00 Z1055

545 TECHNOLITE Boxter 2 luminaire complete with 250W or400W metal halide lamp, steel sheet with powder coatingbody, clear tempered glass diffuser, asymmetricalaluminium reflector and mounting accessories. IP 65.

no $537.70 Z1061

Linkbuilding, Linkway Lights, Steplights, Buried Floodlights & Indoor Lights


546 ALLUM wall mounted luminaire Rugby complete with 1 x18W PLC lamp and UV-stabilised polycarbonate diffuser.

no $70.40 Z0205

547 ARCLUCE ceiling mounted luminaire Monos complete with1x 18W fluorescent, body in extruded aluminium andreeded clear high impact acrylic diffuser.

no $150.30 Z0104

548 ARCLUCE ceiling mounted luminaire Monos complete with1x 36W fluorescent, body in extruded aluminium andreeded clear high impact acrylic diffuser.

no $206.70 Z0105

of 69




Linkbuilding, Linkway Lights, Steplights, Buried Floodlights & Indoor Lights (Cont'd)


549 DIL-MESADO Square surface mounted luminaireMSL.211, housing in die cast aluminium coated with epoxypowder paint, sand blasted UV-stabilised polycarbonatediffuser, hammered aluminium reflector complete with 2 x11W PL warm-white compact fluorescent lamp.

no $122.20 Z0207

550 EXTERIEUR VERT, buried light fitting, M2 IP67 rating, inanodized aluminium housing with mechanical resistanceglass of 8T (or anti vandal polycarbonate 4T), FM 11Wlamp, electronic control gear.

no $494.20 Z0151

551 GHIDINI wall mounted luminaire Ovalla 1101, completewith die-cast aluminium body and opal diffuser, directmounting 2 x 11W PL lamp.

no $151.50 Z0123

552 GHIDINI wall mounted luminaire Ovalla 1103, completewith die-cast aluminium body and opal diffuser, sidemounting 2 x 11W PL lamp.

no $160.70 Z0124

553 GHIDINI wall mounted luminaire Ovalla 1104, completewith die-cast aluminium body and opal diffuser, endmounting 2 x 11W PL lamp.

no $166.40 Z0125

554 VINIC 500601 wall mount luminaire complete with 45Wenergy lamp, integrated ballast, die cast aluminiumhousing, reflector, 5mm thick clear tempered glass lensreflector and bracket.

no $933.50 Z1128

555 UNIVERSAL 114 slim surface wall mount luminairecomplete with 1 x 14/21/28/35W T5 fluorescent lamp,polyster powder coated electro-galvanised steel andpolyster coated reflector.

no $69.80 Z1129

of 69






556 GOCCIA wall/ceiling luminaire Triangolo 4322 completewith 2 x PL 11W lamps and vandal-proof acrylic diffuser.

no $203.20 Z0096

557 GOCCIA wall/ceiling luminaire Triangolo 4346 completewith 2 x PL-L18W lamps and vandal-proof acrylic diffuser.

no $222.20 Z0097

558 GOCCIA wall/ceiling luminaire Triangolo 4380 completewith 1 x 80W super deluxe mercury lamp.

no $312.00 Z0098

559 IGUZZINI 1176 wall washer screen finish in black only foritems Z0135 to Z0148.

no $82.50 Z0150

560 IGUZZINI 1177 louvre finish in black only for items Z0135to Z0148.

no $99.70 Z0149

561 IGUZZINI outdoor floodlight PLATEA 7376 in die-castaluminium, super pure aluminium reflector with flood beamand 2 x 26W TCT compact fluorescent lamp.

no $565.50 Z0144

562 IGUZZINI outdoor floodlight PLATEA 7377 in die-castaluminium, super pure aluminium reflector withasymmetrical beam and 70W metal halide or high pressuresodium lamp.

no $772.50 Z0135

563 IGUZZINI outdoor floodlight PLATEA 7378 in die-castaluminium, super pure aluminium reflector withasymmetrical beam and 150W metal halide or highpressure sodium lamp.

no $795.50 Z0136

564 IGUZZINI outdoor floodlight PLATEA 7379 in die-castaluminium, super pure aluminium reflector with flood beamand 70W metal halide or high pressure sodium lamp.

no $640.20 Z0138

565 IGUZZINI outdoor floodlight PLATEA 7380 in die-castaluminium, super pure aluminium reflector with flood beamand 150W metal halide or high pressure sodium lamp.

no $680.50 Z0139

of 69






566 IGUZZINI outdoor floodlight PLATEA 7385 in die-castaluminium, super pure aluminium reflector with spot beamand 70W G12 metal halide lamp.

no $686.20 Z0145

567 IGUZZINI outdoor floodlight PLATEA 7386 in die-castaluminium, super pure aluminium reflector with spot beamand 150W G12 metal halide lamp.

no $726.50 Z0146

568 IGUZZINI outdoor floodlight PLATEA 7387 in die-castaluminium, super pure aluminium reflector with blade-of-light beam and 70W G12 metal halide lamp.

no $853.00 Z0147

569 IGUZZINI outdoor floodlight PLATEA 7388 in die-castaluminium, super pure aluminium reflector with blade-of-light beam and 150W G12 metal halide lamp.

no $893.20 Z0148

570 IGUZZINI outdoor floodlight PLATEA 7394 in die-castaluminium, super pure aluminium reflector with flood beamand 250W metal halide lamp.

no $761.00 Z0140

571 IGUZZINI outdoor floodlight PLATEA 7395 in die-castaluminium, super pure aluminium reflector withasymmetrical beam and 250W metal halide lamp.

no $899.00 Z0137

of 69






572 KL LICHT wall mounted luminaire Trapez 5007 completewith 70W SON/80W or 125W super deluxe mercury, bodyin cast aluminium and frosted UV-stabilized polycarbonatediffuser.

no $1,255.50 Z0103

573 KL LICHT wall mounted luminaire Zylinder-Quadro 1581complete with 70W SON/50W or 80W super deluxemercury, body in cast aluminium and cylindrical opal UV-stabilized polycarbonate diffuser.

no $1,957.00 Z0101

574 KL LICHT wall mounted luminaire Zylinder-Quadro 1583complete with 70W SON/50W or 80W super deluxemercury, body in cast aluminium with anti-glare louvres andbuilt in cylindrical clear UV-stabilized polycarbonatediffuser.

no $2,060.50 Z0102

575 LUCERNE wall mounted luminaire 502 complete with 2 x11W PL, body in die-cast aluminium and frosted UV-stabilized polycarbonate diffuser.

no $195.20 Z0099

576 LUCERNE wall mounted luminaire 502 complete with 2 x13W or 18W PLC, body in die-cast aluminium and frostedUV-stabilized polycarbonate diffuser.

no $220.50 Z0100

577 MARTIN MULLER ceiling mounted luminaire Cat No.Cristal 211 complete with 2 x 11W PL lamp, high impactresistant acrylic satine diffuser, die-cast aluminium baseand hinged frame and high purity aluminium reflector.

no $128.50 Z0208

of 69






578 NORAL surface mounted luminaire Santa Cruz completewith UV-stabilised polycarbonate diffuser, silver reflector, 2x 11W PL energy saving lamp, standard black or whitefinish.

no $163.00 Z0206

579 NOVALUX decorative column/wall mounted luminaire Type5510 of thermosetting body complete with either white orblack finish, frosted diffuser and 2 x PLC 18W lamp.

no $157.20 Z0091

580 NOVALUX decorative column/wall mounted luminaire Type5512 of thermosetting body complete with either white orblack finish, frosted diffuser and 2 x PL 11W lamp.

no $157.20 Z0090

581 NOVALUX decorative column/wall mounted luminaire Type5514 of thermosetting body complete with either white orblack finish, frosted diffuser and 1 x PLC 18W lamp.

no $157.20 Z0089

582 PLATEK wall mounted luminaire Cat No. Bahia completewith 1 x 18W PLC lamp UV-stabilised polycarbonatediffuser, parabolic aluminium reflector and die-castaluminium body.

no $169.40 Z0201

of 69






583 SIEMENS Sicompact Mini floodlight cat. no 5NA-747-1-2 ofdie-cast aluminium housing, hammered aluminium reflectorand tempered glass lense complete with 1 x 70W metalhalide lamp.

no $306.70 Z0129

584 SIEMENS Sicompact Mini floodlight cat. no 5NA-747-2-2 ofdie-cast aluminium housing, hammered aluminium reflectorand tempered glass lense complete with 1 x 150W metalhalide lamp.

no $330.90 Z0130

585 SIMES surface mounting luminaire Sherma Art.S.6215complete with 1 x PLL-18W compact fluorescent lamp.

no $203.20 Z0093

586 SIMES uplight luminaire Megaflat Round BuriedDrive/Walk Over Art.S.4790 complete with 1 x MH-150Wmetal halide lamp, clear toughened clear glass diffuser,polypropylene tube for recess, IP67.

no $2,237.60 Z0134

587 SIMES uplight luminaire Ring Drive/Walk Over Art.S.4928complete with 1 x PLCT-18W lamp, toughened clear glassdiffuser, polypropylene tube for recess, IP 67.

no $765.60 Z0131

588 SIMES uplight luminaire Ring Drive/Walk Over Art.S.4929complete with 1 x PLCT-18W lamp, toughened acidatedglass diffuser, polypropylene tube for recess, IP 67.

no $740.30 Z0132

589 SIMES uplight luminaire Ring Drive/Walk Over Art.S.4930complete with 1 x 70W metal halide lamp, toughenedacidated glass diffuser, polypropylene tube for recess, IP67.

no $1,382.00 Z0133

590 SIMES wall/ceiling mounted luminaire Art.S.6749 with UV-stabilised polycarbonate diffuser complete with 18W PLClamp.

no $177.90 Z0203

591 SIMES wall/ceiling mounted luminaire MEGAVEDOROUND Art.S.6869 with PMMA diffuser and 2 x 11W PLlamp.

no $206.70 Z0210

592 SPECTRA UPLIGHTER TRENTO S13104 complete with80W mercury super deluxe lamp and high strengthborosilicate glass.

no $1,623.50 Z0155

of 69






593 SPECTRA UPLIGHTER TRENTO S13106 complete with125W mercury super deluxe lamp and high strengthborosilicate glass.

no $1,658.00 Z0156

594 SPECTRA UPLIGHTER TRENTO S13110 complete with70W metal halide lamp and high strength borosilicateglass.

no $1,738.50 Z0152


no $1,830.50 Z0153


no $1,876.50 Z0154

597 SPECTRA UPLIGHTER TRENTO S13120 complete with70W SON lamp and high strength borosilicate glass.

no $1,750.00 Z0157

598 SPECTRA WASHLIGHTER TRENTO S13200 completewith 70W metal halide lamp and high strength borosilicateglass.

no $1,761.50 Z0158

599 SPECTRA WASHLIGHTER TRENTO S13205 completewith 150W metal halide lamp and high strength borosilicateglass.

no $1,876.50 Z0159

600 SPECTRA WASHLIGHTER TRENTO S13210 completewith 70W SON lamp and high strength borosilicate glass.

no $1,761.50 Z0160

601 Stainless steel louvre (anti-glare) TTL 90°/TTL 150° foritems Z0152 to Z0160.

no $163.00 Z0161

602 Surface wall mounted luminaire cat no. Tubo5700.NK.P109.1 of alloy housing, built-in capsulated ballastand polycarbonate diffuser complete with Osram DuluxS9w lamp.

no $197.50 Z0092

603 LIGMAN wall mounted luminaire Cat No. 30302 completewith 1 x 18W PLC lamp, IP 55, opal UV stabilisedpolycarbonate diffuser, die-cast aluminium body andfaceplate louvre.

no $126.20 Z0202

of 69





604 WE-EF accent floodlight, IP55 FL131-DT-18(.B), corrosionresistant die-cast aluminium alloy body and frame, finish inRAL polyester powder coat, thermal shock resistant safetyglass, weatherproof and durable silicone rubber gasket andElectronic 20W lamp.

no $622.00 Z0128

605 WE-EF steplight, IP 55 STG259-DD-13(I) or 18(I) corrosionresistant die-cast aluminium alloy body and frame,polycarbonate UV-stabilized and vandal resistant diffuser,two cable entries to facilitate through wiring, and Electronic15W lamp.

no $177.00 Z0126

606 WE-EF steplight, IP 55 STL259-DD-13(I) or 18(I) corrosionresistant die-cast aluminium alloy body and frame,polycarbonate UV-stabilized and vandal resistant diffuser,two cable entries to facilitate through wiring, and Electronic15W lamp.

no $177.00 Z0127

607 WE-EF wall luminaire surface DLB259-DD-13(I) IP55,corrosion resistant die-cast aluminium alloy body andframe, finish in RAL polyester powder coat, polycarbonateUV-stabilized and vandal resistant diffuser, weatherproofand durable silicone gasket and Electronic 20W lamp.

no $251.50 Z0120


no $251.50 Z0121


no $251.50 Z0122

of 69






610 SPECTRUM LINK wall/ceiling mounted luminarie completewith 1 x 18W PLC lamp, die-cast aluminium body and highimpact resistant UV stabilised polycarbonate diffuser.

no $83.80 Z1001

611 BOLUCE ALFA ROUND 3020 wall/ceiling mountedluminarie complete with 1 x 18W PLC lamp, die-castaluminium body complete with cross guard and UVstabilized polycarbonate diffuser.

no $113.50 Z1014

612 SPRING SP-1018 round column/wall/ceiling mountedluminarie complete with 1 x 18W PLC lamp, die-castaluminium body with polyester powder finish,polymethylmethacrylate (PMMA) diffuser and Quick LockAllen Key Screws.

no $105.50 Z1018

613 GALA LUZ BELLE OVALE wall/ceiling mounted luminariecomplete with 1 x 18W PLC lamp, die-cast aluminium baseand polycarbonate housing and opal or frosted UVstabilized polycarbonate diffuser.

no $127.30 Z1037

614 LIGMAN 30084 wall mounted luminarie complete with 1 x18W PLC lamp, die-cast high corrosion resistant aluminiumhousing, durable silicone rubber gasket and UV stabilizedvandal proof polycarbonate diffuser.

no $114.70 Z1053

of 69






615 TECHNOLITE LUC290-118PLC round column/wall/ceilingmounted luminarie complete with 1 x 18W PLC lamp, die-cast aluminium body, strip-frosted UV stabilizedpolycarbonate diffuser and aluminium reflector.

no $126.20 Z1059

616 ARCLUCE MONOS 1020 extruded aluminiumcolumn/wall/ceiling mounted luminarie complete with 1 x18W linear fluorescent lamp and metallised aluminiumlouver.

no $127.30 Z1060

617 HUGO 5301 wall/ceiling mounting luminarie complete with1 x PLC-18W/G24d-2 (3000Kº) warm-white CompactFluorescent lamp, die-cast aluminium housing and frostedpolycarbonate diffuser.

no $75.00 Z1068

618 SPECTRUM ALPHA surface mounted luminaire completewith 1 x 18W fluorescent lamp, electro-galvanised steelsheet metal body with polyester powder coated finish,aluminium or electro-galvanised steel sheet metal withpolyester powder coated reflector.

no $74.50 Z1002

619 SPECTRUM ALPHA surface mounted luminaire completewith 2 x 18W fluorescent lamp, electro-galvanised steelsheet metal body with polyester powder coated finish,aluminium or electro-galvanised steel sheet metal withpolyester powder coated reflector.

no $84.90 Z1003

620 WAVE (rounded) W(R)118 surface/ceiling mountedluminaires complete with 1 x 18W fluorescent lamp, coldsteel body with powder coated finish and powder coatedsteel or TR>=80% aluminium back reflector.

no $107.80 Z1008

621 WAVE (rounded) W(R)218 surface/ceiling mountedluminaires complete with 2 x 18W fluorescent lamp, coldsteel body with powder coated finish and powder coatedsteel or TR>=80% aluminium back reflector.

no $126.20 Z1009

622 ILMAS LAGUNA LG118 surface mounted luminairecomplete with 1 x 18W fluorescent lamp, electro-galvanised steel body with smooth epoxy-powder coatingfinish and aluminium reflector.

no $76.70 Z1015

of 69






623 ILMAS LAGUNA LG218 surface mounted luminairecomplete with 2 x 18W fluorescet lamp, electro-galvanisedsteel body with smooth epoxy-powder coating finish andaluminium reflector.

no $88.20 Z1016

624 SIMLITE BSS120 surface mounted luminaire complete with1 x 18W fluorescent lamp, galvanised sheet steel housingwith epoxy powder coating finish and glossy epoxy powderreflector.

no $80.20 Z1033

625 SIMLITE BSS120 surface mounted luminaire complete with2 x 18W fluorescent lamp, galvanised sheet steel housingwith epoxy powder coating finish and glossy epoxy powderreflector.

no $91.70 Z1034

626 GALA LUZ decorative surface mounted luminaire FARGOcomplete with 1 x 18W tubular linear fluorescent lamp,extruded aluminium body with polyester powder coatedfinish and matt aluminium reflector.

no $99.70 Z1038

627 GALA LUZ decorative surface mounted luminaire FARGOcomplete with 2 x 18W tubular linear fluorescent lamp,extruded aluminium body with polyester powder coatedfinish and matt aluminium reflector.

no $111.20 Z1039

628 LUCAS decorative surface mounted luminiare PICASSOSeries HE6002 complete with 1 x 18W tubular (linearfluorescent) lamp, powder coated electro-galvanised sheetsteel housing and reflector and mounting accessories.

no $81.30 Z1041

629 LUCAS decorative surface mounted luminiare PICASSOSeries HE6003 complete with 2 x 18W tubular (linearfluorescent) lamp, powder coated electro-galvanised sheetsteel housing and reflector and mounting accessories.

no $92.80 Z1042

630 AEROLITE TREO/118/E surface mounted luminariecomplete with 1 x 18W fluorescent lamp, electro-galvanised steel body with polyester coating finish,aluminium matt finish or electro-galvanised steel reflectorwith polyester coating finish.

no $65.20 Z1049

of 69






631 AEROLITE TREO/218/E surface mounted luminariecomplete with 2 x 18W fluorescent lamp, electro-galvanised steel body with polyester coating finish,aluminium matt finish or electro-galvanised steel reflectorwith polyester coating finish.

no $74.40 Z1050

632 FORMULA 1 F1XZ114R surface mounted luminairecomplete with 1 x 14W linear fluorescent lamp, cold rollsteel body with powder coating finish and aluminiumreflector.

no $99.70 Z1065

633 FORMULA 1 F1XZ214R surface mounted luminairecomplete with 2 x 14W linear fluorescent lamp, cold rollsteel body with powder coating finish and aluminiumreflector.

no $111.20 Z1066

634 HUGO – F.120.FMR surface ceiling mounted luminariecomplete with 1 x FLT-18W/G13 (3000Kº) warm-whitetubular fluorescent lamp, heavy gauge electro-galvanisedsteel base with extruded aluminium rounded side housingand matt aluminium reflector.

no $80.80 Z1069

635 HUGO – F.220.FMR surface ceiling mounted luminariecomplete with 2 x FLT-18W/G13 (3000Kº) warm-whitetubular fluorescent lamp, heavy gauge electro-galvanisedsteel base with extruded aluminium rounded side housingand matt aluminium reflector.

no $92.30 Z1070

of 69





Lighting luminaires complete with approved electronic magnetic ballast(s) and other accessories:

636 VEWA CUBIC C118 recessed downlight complete with 1 x18W PLC Compact Fluorescent lamp, powder coated steelframe body with square shape die-cast silver aluminiumtrim and matt aluminium reflector.

no $96.30 Z1010

637 VEWA CUBIC C213 recessed downlight complete with 2 x13W PLC Compact Fluorescent lamp, powder coated steelframe body with square shape die-cast silver aluminiumtrim and matt aluminium reflector.

no $110.10 Z1011

638 GE FOH8621 213L recessed downlight complete with 2 x13W PLC Compact Fluorescent lamp, powder coated steelframe body, matt aluminium reflector and extrudedaluminium housing.

no $76.70 Z1021

639 ILLIS IL-16003 recessed downlight complete with 1 x 18Wor 2 x 13W PLC Compact Fluorescent lamp, powdercoated steel frame body and matt aluminium reflector.

no $64.10 Z1040

640 LUCENT HS6182H ceiling recessed downlight completewith 1 x 18W or 2 x 13W PLC Compact Fluorescent lamp,powder coated steel frame body and electro-galvanisedsheet housing with frosted reflector.

no $65.20 Z1043

641 LEOLITE 6022 recessed downlight complete with 2 x 13WPLC Compact Fluorescent lamp, electro-galvanised steelframe, die-cast aluminium trim and sand blasted aluminiumreflector.

no $57.20 Z1051

642 LUMITECH 0750 recessed downlight complete with 2 x13W PLC Compact Fluorescent lamp, powder paintedwhite metal trim body and matt anodised aluminumreflector.

no $68.70 Z1054

643 THORN Chalice 2 CDHS 213M recessed downlightcomplete with PLC 13W / 2Pin Compact Fluorescent lamp(twin), zinc coated steel with epoxy painted white metalbezel body and matt anodised aluminium reflector.

no $68.70 Z1067

of 69






644 ITAC - RDL6182H ceiling recessed downlight completewith 1 x 18W or 2 x 13W PLC Compact Fluorescent lamp,polyester powder coated electro-galvanised steel framebody, die-cast aluminium trim housing and matt anodisedaluminium reflector.

no $59.50 Z1071

Aviation Obstruction Light

645 Twin units aviation obstruction light (lightmast, control box,cables, cable trunking/tray & conduits measuredseparately).

no $868.90 SZ961

646 Twin units aviation obstruction light complete with lightingcontrol box and lightmast (cables, cable trunking/tray &conduits measured separately).

no $937.90 SZ905

I EMERGENCY/EMERGENCY EXIT SIGN LUMINAIRES

647 1x8W/10W slim maintained emergency exit light (single ordouble sided) surface or recessed mounting andwith/without (arrows) complete with 2 hrs ni-cad batteries,IP 20.

no $81.60 SZ658

648 2x8W box type sustained emergency exit light (single ordouble sided) complete with 2 hrs ni-cad batteries, IP30.

no $71.70 SZ660

of 69



I EMERGENCY/EMERGENCY EXIT SIGN LUMINAIRES (CONT'D)

649 2x8W box type non-maintained emergency light completewith 2hrs ni-cad batteries, IP30.

no $71.00 SZ663

650 Dia. 5mm white LED type maintained emergency exit light(single or double sided) with or without arrows, completewith 2 hrs ni-cad batteries, IP30.

no $102.00 Z0233

651 Dia. 5mm white LED type non-maintained emergency exitlight complete with 2 hrs ni-cad batteries, IP30.

no $82.80 Z0234

652 2x5W tungsten halogen lamps non-maintained floodlightemergency light complete with 1.5 hrs maintenance freelead acid batteries, IP20.

no $72.80 SZ666

653 1x10W halogen lamp miniature recessed mounted non-maintained emergency light complete with 1.5 hrsmaintenance free lead acid batteries, IP20.

no $70.20 SZ668

654 Emergency conversion kit for 18W and 36W tubularfluorescent lamp for 2 hrs rated duration.

no $70.20 SZ671

655 White LED Internal Exit Light complete with 2-hour nickel cadmium batteries, IP 30.

no $94.00 Z0214

of 69



J FIRE ALARM ACCESSORIES

656 Manual break glass call point. no $33.70 SZ672

657 Weather resistant gasket for weatherproof manual callpoint.

no $36.50 SZ673

658 Weatherproof manual break glass call point complete withgasket (IP65).

no $149.70 SZ674

659 Ionisation smoke detector complete with LED and mountingbase.

no $76.00 SZ675

660 Optical smoke detector complete with LED and mountingbase.

no $73.20 SZ676

661 Fixed temperature cum Rate of Rise (ROR) heat detector(Type A) complete with LED and mounting base.

no $51.40 SZ677

662 Fixed temperature heat detector (Type B) complete withLED and mounting base.

no $50.50 SZ678

663 Fixed temperature heat detector (Type D) complete withLED and mounting base.

no $59.40 SZ679

664 Fixed temperature bi-metallic heat detector (Type B orGrade 2) complete with LED .

no $45.00 Z0245

665 Fixed temperature bi-metallic heat detector (Type D)complete with LED.

no $54.00 Z0246

666 Alarm bell. no $42.90 SZ680

667 Alarm bell complete with integral strobe light. no $103.60 SZ681

668 Weatherproof base box for alarm bell. no $42.60 SZ682

669 Weatherproof strobe light 24V dc (IP65). no $71.90 SZ683

of 69



K TELEVISION SYSTEM

Broadband

670 Bridger Amplifier (cable TV distribution amplifier) no. $2,946.20

671 Trunk Amplifier (cable TV distribution amplifier) no. $3,367.00

Accessories (for Bridger/Trunk amplifier)

672 Cable Attenuator - SPB-X (where X denotes 0 to 20) no. $37.60

673 Cable Equaliser no. $55.70

674 Cable Simulator no. $71.40

675 Plug-in Directional Coupler no. $109.40

676 Plug-in Splitter no. $109.40

Coaxial Cable

677 Coaxial Cable (for RG-6 type) m $1.50

678 Coaxial Cable (for 'solid' type) m $9.00

679 Coaxial Cable (for underground type) m $10.30

S Connector

680 Connector ('F' Male) (for RG-6 type) no. $2.60

681 Connector ('F' Male) (for '412' type) no. $24.00

682 Connector ('F' Male) (for '540' type) no $26.00

683 Connector (pin) (for '412' type) no. $28.60

684 Connector (pin) (for '540' type) no. $29.90

685 Connector (splice) (for '412' type) no. $59.60

686 Connector (splice) (for '540' type) no. $84.30

687 Connector (terminator) (for RG-6 type) no. $2.20

688 Connector (terminator) (for unused port of OUTDOOR tap, etc) no. $18.40

20A Isolator

689 Master Key Switch type no. $136.00

of 69



K TELEVISION SYSTEM (CONT'D)

Power Supply

690 Power Supply (2A) (for cable TV) no. $716.90





695 Power Supply (15A) (for cable TV) no. $2,123.90

Splitter

696 Splitter (2-way) (indoor) no. $22.70




700 Splitter (2-way) (outdoor) no. $230.60

701 Splitter (3-way) (outdoor) no. $235.60

Subscriber Outlet - Isolator

702 Outlet (Isolator type) no. $26.10

703 Outlet (base, 1 ½ gang type) no. $26.10

704 Outlet (base, 2 gang type) no. $32.60

705 Outlet (TV/FM front plate, 1½ gang type) no. $27.90

706 Outlet (TV/FM front plate, 2 gang type) no. $32.60

of 69




Tee Unit

707 Tee unit (2-way) (outdoor) no. $87.60



710 Tee unit (Directional Coupler) no. $181.30

711 Tee unit (Power Inserter) no. $235.60

Metal Conduits - BS4568 including painting and others associated with the work

712 20 mm diameter m $12.70


PVC Conduits - HEAVY GAUGE including painting and others associated with the work




717 110 mm diameter m $36.70

of 69




Miscellaneous Items

718 Metal Tap-Off box (Heavy duty type) - (200(L) x 200(B) x 600(H)) mm approx., with lock & concrete mix base (400(L) x 400(B) x 300(H)) mm approx.

no. $162.00

719 Metallic tee/splitter box (200(L) x 180(B) x 350(H)) mm approx.

no. $93.90


no. $87.60


no. $81.00

722 Metal concealed isolator box (80(L) x 38(B) x 110(H)) mm approx.

no. $46.60

723 Amplifier bracket complete powder coating (for Cable TV distribution amplifier)

no. $55.10

724 PVC trunking inclusive of PVC saddles & 'Hilti' nails or equivalent (20 x 40) mm approx.

m $4.00

725 PVC trunking inclusive of PVC saddles & 'Hilti' nails or equivalent (50 x 50) mm approx.

m $7.80

726 PVC trunking inclusive of PVC saddles & ‘Hilti’ nails or equivalent (100 x 50) mm approx

m $15.90

HDB SOR - Jul 2013

Documents

Transcript of HDB SOR - Jul 2013