Specification of H.264 Remote Controller DV

H.264 FULL HD 1080P 30-frame DV

Product schematic diagram;

H.264 1080P Porsche remote controller DV

Camera lens

Infrared night light

Indication lamp

720P 1080P video record button

Shooting and motion detection button

ON/OFF button and night light

Reset SD card

H.264 1080P BMW remote controller DV

Hanging buckle

USB SD card and reset button

ON/OFF button and night vision button

Shooting and motion detection button

720P 1080P video record button

Indication lamp

Camera lens

Infrared night light

H.264 1080P Benz remote controller DV

Camera lens

Infrared night light

Indication lamp

720P 1080P video record button

Shooting and motion detection button

ON/OFF button and night light

Reset SD card

1. Hanging buckle 2. ON/OFF button (ON/OFF button of the infrared lamp) 3. Shooting button

1200M (4032*3024) motion detection shooting button 4. 720P/1080p shooting button 5. LED

indication lamp 6. Invisible infrared night lamp 7. High definition camera lens 8. Microphone 9.

Reset port 10. TF card port 11. USB interface (USB wire with three purposes: 1. Recording while

charging, 2. Connected to the computer to read the data, and 3. TV OUT video monitoring)

Description of accessories

1. USB data TV OUT wire 2. Optical disk 3. Specification

Product features

High-quality image shooting and high definition H.264 HD

Small appearance design and portable hand-hold DV DC

Support the network camera lens and have the network chart function.

The recording of high definition image can be performed at low illumination.

1200M high definition shooting for each (4032*3024)

Video format 1: 1280*720P 30 frames for each second

Video format 2: 1920*1080P 30 frames for each second

USB2.0 interface of high speed transmission

T-flash card for supporting 64G at most

The built-in lithium battery can shoot for 80min continuously.

Operating instruction

Charging:

The rechargeable lithium battery can be built in the machine. Please charge the machine first

while using the machine for the first in the following modes:

1) Connect to the computer for charging, wherein USB is connected with the computer for

charging.

2) The charger is used for charging, the USB data wire is inserted and connected with the

charger base, and then the charger shall be inserted onto the electrical socket, the charging can

be performed (capable of recording while charging). When the red indication lamp is turned

on, it shows that the charging is completed.

Attention: When the battery electricity is not enough and the T card is recorded completely,

DV red and blue lamps will enter into the protection state directly after quick flashing (the

document is protected and the machine is shut down automatically), the recording document

has been recorded. Please charge the machine at this moment.

One wire with three purposes:

USB with TV wire: 1. Insert the wire into the computer to charge the computer and transmit the

data.

2. Insert the wire into the TV OUT screen to display.

3. Insert the wire into the DV 5V externally for recording while charging.

Definitions of button function:

Pleasure confirm that the T-F card has been inserted into the product (if the machine is

started up without the T card, the machine will be shut down automatically after the red and blue

lamps flash for 10s; if the machine is started up for standby without any function, the machine will

be shut down automatically within 1min for storage; if the TF card is recorded completely, or the

battery is out of electricity, the red and blue lamps will flash for 5s in double, the document will be

stored automatically, and the machine will be shut down).

Infrared opening/closing of ON/OFF button

Click and press the lowest button (button of vehicle end tank), which is the power button. After

starting up, press the power button for one time, the red indication lamp is turned on normally and

the blue indication lamp flashes for two times, it is deemed as that the infrared night light is turned

on. Click and press the ON/OFF button for one time, the red indication lamp is turned on normally

and the blue indication lamp flashes for four times, it is deemed as that the mode of the infrared

night light shall be closed.

H.264 720P video recording and 1080P video recording

In the starting state, click and press the BMW identification mark for one time, the red indication

lamp is turned off after flashing for three times, it is the 720P video. Click and press any button to

stop recording, and return to the standby mode. Press the recording button for 2s, and the blue

indication lamp is turned off after flashing for three times. Enter into the 1080P recording mode.

Click and press any button to stop recording, and return to the standby mode.

Shooting and motion detection

Start up, click and press the upmost button for one time, the blue indication lamp will flash for one

time, and the shooting mode is 12 million pixels. Press the button for 2s, and the red indication

lamp will be turned off after flashing for three times. Enter into the motion detection mode. The

automatic recording will be performed with the motion, and the motion detection standby will be

kept always without the motion. Press any button to stop recording and return to the standby

mode.

Recording while charging: Insert the USB wire, connect the 5V USB power supply

externally, and make the machine enter into 720P shooting mode for recording directly (adjust any

other mode by oneself), perform recording till the card is recorded completely or there is not the

electricity without manual stop.

TV OUT mode: Connect the USB TV wire, start up, connect the TV video, watch the

image by the TV screen, perform shooting, video recording and monitoring at this moment.

Shutdown: Perform shutdown in the function mode of stopping recording and shooting,

press the ON/OFF button for about 3s, the red and blue indication lamps are turned off, and the

shutdown is performed. Or under the condition of not using any function in the standby mode,

automatic shutdown will be performed after being standby for 1min.

Reset: If the machine is crashed, the button is invalid and cannot be used normally, the

needle can be inserted by aiming at the reset port to reset the machine, and the machine can be

started up for use normally after being reset.

Attention:

a. Please confirm that the T-flash (Micro SD) card has been inserted into the product. If

not, double flash of the red and blue indication lamps of the product cannot be used

normally.

b. Please make the camera lens aim at the shooting object in the environment with

enough illumination, keep the camera lens at a distance of 50cm and above from the

shooting object, thus, the right image with natural color, clear scenery and stable

picture can be obtained.

Time modification and setting

Through the mode of connecting USB to the computer, after the modification time

of the TIMERSET.TXT text file of the accessory optical disk, the TEX document shall be copied

to the root directory of the U disk mode, and then the USB wire shall be pulled out, DV shall be

started up again for one time, the time watermark of the RTC is written into the machine. The

same operation mode is also provided without the time watermark. The content format is as

follows:

1. 20130508142432 Y video document is 1280*720P (with time watermark display).

2. 20130508142432 N video document is 1280*720P (without time watermark display).

Connect to the computer

Connect to the computer in the starting state and the shutdown state. Be able to be used as the

U disk after being connected to the computer, copy, paste and cancel the document, and

format the U disk.

The machine shall be inserted into the USB interface of the computer, the computer will pop

up the identification of the removable disk after several seconds, the blue indication lamp is

turned on, and the USB identification device can transmit the data. The red indication lamp

is turned on, which shows that the charging is performed, and the red indication lamp is

turned off, which shows that the charging is completed.

Prompt:

a. When the machine is connected to the computer, if the computer cannot perform

recognition or still does not pop up the identification of the removable disk after 30s, please

reset, insert and plug for one time again.

b. The T card reader shall be used for reading the video document directly for playing by

suggestion. However, as the data amount is too large and the transmission cannot be kept up,

it may be not smooth to play the video document stored in the built-in memory of the video

tape recorder by USB connection directly.

Function of computer camera lens:

Function of PC camera lens (optional)

After being provided with the optical disk DRIVER, the product can be used as the PC

camera lens. In the shutdown state, press K3 always, insert the USB device and make the

same connected with the computer for some seconds approximately, leg go at this moment,

and the product can be used as the camera lens.

Relevant Parameters

Project Relevant Parameters

Video format H.264

Video encoding MOV

Video resolution 1280*720P HD 1920*1080 HD

Video frame rate 60fps

Play software The operating system is provided with the mainstream video play

software.

Picture format JPG

Image proportion 4:3

Support system Windows me/2000/xp/2003/vista; Mac os; Linux;

Battery capacity 420mAh

Working time About 80min

Charging voltage DC-5V

Interface type Mini 8Pin USB

Storage support TF card

Battery type High capacity polymer lithium battery

Precautions

Usage plate: Please observe and follow the relevant national laws strictly. This product may

not be used for any illegal purposes, or there'll be some consequences.

Operating temperature: Please use the product at the natural temperature. Please do not

operate at the temperature that the human body cannot be adaptive.

Operating humidity: Please use the product at the environment humidity applicable for the

human to live. Please do not locate the product in the humid working environment. As the

product is provided with the waterproof function, please avoid the product from being

poured by the water or exposed in the rainwater.

Shooting illumination: Please use the product in the environment with enough light sources.

Please do not make the camera lens face the sun and other super-strong light source to avoid

the optical device from being broken.

Cleaning requirement: Please do not use the product in the environment with overlarge dust

density to avoid the camera lens and other components from catching the dust to affect the

shooting effect.

Waste treatment: Please pay attention to the environmental protection. Do not discard the

product optionally. Prohibit putting the product into the fire to avoid the explosion.