Grout Application Guide

Grout Name Description Sys # Cu. Ft./Unit Applications Precautions

Stonset TG5 3 Component, General

Service, Trowelable Epoxy Grout

3212 2.00 Pitching, Patching, and Leveling

0.5" to 1.0" Thickness

Minimum Thickness of 0.5 inches. When trowelling,

maximum 2 inch lifts.

Stonset TG4 4 Component, General

Service, Trowelable Epoxy Grout

3253 2.75 Pitching, Patching, and Leveling

1.0" and Greater Thickness

Minimum Thickness of 1 inch. When trowelling,

maximum 2 inch lifts. Large volume mortar mixer required.

Stonset TG6 4 Component, Trowelable Urethane Grout

3214 2.67 Pitching, Patching, and Leveling 0.5" to 1.0" Thickness

Minimum Thickness of 0.5 inches. MUST ADD PART C!!!

Stonset TG8 4 Component, Trowelable Vinyl Ester Grout

3216 0.75 Pitching, Patching, and Leveling 0.5" to 1.0" Thickness

Minimum Thickness of 0.5 inches. When trowelling, maximum 2 inch lifts. MUST BE TROWELLED OVER

CURED 800 SERIES PRIMER. NEVER MIX COBALT COMPONENT WITH PEROXIDE!!!

Stonset CR5 4 Component, Epoxy Grout 3259 2.25 Trowelable Grout for Use UNDER

LINING SYSTEMS Trowel into wet HT Primer

Stonset HG5 3 Component, Chemical

Resistant, Trowelable Epoxy Grout

3261 2.00 Pitching, Patching, and Leveling

0.5" to 1.0" Thickness

Minimum Thickness of 0.5 inches. When trowelling,

maximum 2 inch lifts.

Stonset PM5 2 Component Epoxy Patching Mortar

3223 830 in.3

Patching Bugholes, Rough Areas, Mortar Lines, C&L Radius Details,

and GMP Coves

Must be mixed 1:1.

Stonset PM8 3 Component, Vinyl Ester

Patching Mortar 946 830 in.

3

Patching Bugholes, Rough Areas,

Mortar Lines, C&L Radius Details, and GMP Coves UNDER VINYL

ESTERS

Follow mixing instructions exactly.

Stonset QS5 2 Component, Quick Setting Epoxy Patching Material

3230 Patching and Filling Pinholes in SL Primer Applications. Adhesive for

Bond Caps and Cove/Floor Strip

Must be mixed 1:1. SETS IN 5 MINUTES!!! Only mix small amounts.

Stonset CG5 4 Component, Castable

Epoxy Grout 3203 2.00

Forming Pump Pads, Curbs, and

Retaining Walls Seal forms well. Tape wood forms.

Stonset CG4 4 Component, Castable,

Novolac Epoxy Grout 3206 2.00

Forming Pump Pads, Curbs, and

Retaining Walls Seal forms well. Tape wood forms.

Stonset HS1 Heavy Duty, Cementitious

Lining Material 20001 3.66

Repairing spalling concrete, pouring

caps

Consult Product Data for application instructions and

important curing information.

Stonset PC3 Water-Based, Epoxy Binder 945 0.5 Repairing spalling concrete, honeycombs/voids in vertical

concrete surfaces

Mix ratios and application instructions must be carefully followed for material to fully cure.

Stonset OP2 Cementious Latex Osmotic

Pressure Barrier 3151 2

Preventing disbonding of overlayment

due to high moisture transmission through existing slabs

Must be applied over dried OP2 Primer Latex

08/09