Gravimetric & Volumetric Feederss3.amazonaws.com/Younginds.info/Product Info/Website...

PH: 570-546-3165 FAX: 570-546-1888E-mail: [email protected]

www.younginds.com

BULLETIN 270-200

Engineered to Increase Productivityand Built to Last

Gravimetric & Volumetric Feeders

®

The Young Industries, Inc. - BULLETIN 270-200 -

The Best Weighing Accuracy of Fine Powders

®Young Industries STINGER feeder is a gravimetric loss-in-weight, gain-in-weight, or volumetric feed system designed

®for handling fine and cohesive powders. The STINGER feeder solves common feeding problems that occur when handling these powders including no flow, flooding, rat holing, limited discharge rate, and product separation.

Unlike other gravimetric feeders that use brute force to ®

make fine materials flow, the STINGER feeder uses energy ®efficient TransFlow Technology. This technology conditions

the powders with a layer of air making it easy for them to flow and eliminates the expensive maintenance cost of the high horsepower motorized drives.

®The STINGER feeder design was originally developed for handling Ti02 and other pigment powders

The Young Industries, Inc. has been designing compounding and batch weighing systems for over 50 years. In the past when we supplied these systems, we purchased feeders from other manufactures and incorporated them into our system design. These feeders use vibration or flexible hoppers and motor drive agitation to force fine powders to flow. We experienced the same problems with these feeders that everyone has including frequently repairing flexible hoppers and replacing damaged screws due to overloading by the high horsepower

®motorized drives. Our development of TransFlow Technology produced an improved manner to handle and control the feeding of fine powdered materials.

®The STINGER feeders are most appropriate for feeding cohesive, fine and ultra-fine particle materials

The majority of fine powders are difficult-to-handle materials

that tend to pack, cake, smear, break apart, flush or bridge. ®

The STINGER feeder accurately feeds titanium dioxide, zinc oxide, iron oxide, carbon black, pigments, clays and other difficult-to-handle materials.

®TransFlow Technology makes it easy for the material to flow

®The unique feature of all STINGER feeders is the use of ®TransFlow aeration media technology. This technology is

used in the weigh hopper and the feed tube components. ®Transflow is a porous 316 stainless steel construction media

with an ultra smooth finished contact surface. This media produces an evenly distributed layer of air or gas that conditions the product above it. This layer of air and product makes it easy for the material to move and slide.

Two Feed Methods for exclusive application advantages

®STINGER Feeder is available in two distinct feed method configurations as described below. In short, the difference between the two feed configurations are related to the feed method.

® Model STS STINGER feeder tube uses an auger to regulate materials. The speed of the feed is limited to the capacity of the screw.

® Model ST STINGER feeder tube feeds material without an auger so the feeder is not limited by the capacity of the auger. Feed rates of a Model ST feeder are generally much faster than that of a Model STS feeder. However with the high rate of feed, accuracy with a model ST Feeder is often less than that which can be achieved when using an auger to regulate flow.

Features Model “STS” Feeder Tube Model “ST” Feeder Tube

Feeder Tube Feed Method TransFlow + Auger TransFlow Only

Feed Applications Batch, Rate, Volumetric Batch

Feed Control Range 100:1 500:1

Feed Rate Standard up to 800 cu. ft. per hr., Options available up to 9,000 cu. ft.

per hr.

Model 1 up to 30,000 lbs. per hr.Model 2 up to 300,000 lbs. per hr.

Batch Accuracy +\- .1% or better Up to +/- .1 lb

No. of moving parts in product area 1 0

Length of Feeder Tube Max. 6 ft. Model 1 max.10 ft.Model 2 max.20 ft.

Ability to feed around corners No Yes - Max. 90° per turn

Ability to feed up hill Max. 10 degrees Max. 90 degrees

The Best Weighing Accuracy of Fine Powders

®Young Industries STINGER feeder is a gravimetric loss-in-weight, gain-in-weight, or volumetric feed system designed

®for handling fine and cohesive powders. The STINGER feeder solves common feeding problems that occur when handling these powders including no flow, flooding, rat holing, limited discharge rate, and product separation.

Unlike other gravimetric feeders that use brute force to ®

make fine materials flow, the STINGER feeder uses energy ®efficient TransFlow Technology. This technology conditions

the powders with a layer of air making it easy for them to flow and eliminates the expensive maintenance cost of the high horsepower motorized drives.

®The STINGER feeder design was originally developed for handling Ti02 and other pigment powders

The Young Industries, Inc. has been designing compounding and batch weighing systems for over 50 years. In the past when we supplied these systems, we purchased feeders from other manufactures and incorporated them into our system design. These feeders use vibration or flexible hoppers and motor drive agitation to force fine powders to flow. We experienced the same problems with these feeders that everyone has including frequently repairing flexible hoppers and replacing damaged screws due to overloading by the high horsepower

®motorized drives. Our development of TransFlow Technology produced an improved manner to handle and control the feeding of fine powdered materials.

®The STINGER feeders are most appropriate for feeding cohesive, fine and ultra-fine particle materials

The majority of fine powders are difficult-to-handle materials

Features Model “STS” Feeder Tube Model “ST” Feeder Tube

Feeder Tube Feed Method TransFlow + Auger TransFlow Only

Feed Applications Batch, Rate, Volumetric Batch

Feed Control Range 100:1 500:1

Feed Rate Standard up to 800 cu. ft. per hr., Options available up to 9,000 cu. ft.

per hr.

Model 1 up to 30,000 lbs. per hr.Model 2 up to 300,000 lbs. per hr.

Batch Accuracy +\- .1% or better Up to +/- .1 lb

No. of moving parts in product area 1 0

Length of Feeder Tube Max. 6 ft. Model 1 max.10 ft.Model 2 max.20 ft.

Ability to feed around corners No Yes - Max. 90° per turn

Ability to feed up hill Max. 10 degrees Max. 90 degrees

Model 1 Advantages

The “STS-1 and ST-1” feeder tubes

are used with Model 1 Square

STINGER Feeders. The Model 1 is ®

designed with economy and space-

savings in mind. The compact hopper

is usually recommended for handling

the lower feed rates on batch weighing,

continuous gravimetric loss-in weight

and volumetric applications.STS-1 STINGER Feeder

®

Model 1

Model 2 Advantages

The “STS-1 and ST-1” feeder tubes

are used with Model 2 Round

STINGER Feeders. The Model 2 ®

Feeder is designed for high throughput

capacity applications. The standard

hopper is usually recommend for feed

rates greater than 800 cu. ft. per hour

on batch weighing, continuous

gravimetric loss-in-weight and

volumetric applications.

STS-2 STINGER Feeder ®

Model 2

STS = STINGER Screw DischargeST = STINGER Discharge

2 = Standard Hopper1 = Compact Hopper

Feed Tube Diameter

Hopper Size

Example: STS-2-4-50

STINGER Feeder Model No. STS-2-6-100 ®

Typical STINGER Feeder Models


STINGER Feeder Model No. STS-2-1.5-3 ®

STINGER Feeder Model No. STS-1-1.5-1.5 ®



®The STINGER gravimetric and volumetric feeders are controlled by the Touchstone™ Control Systems. This system is complete with a 10.4” color touch screen display assembled in a NEMA 4 enclosures with a copyrighted software program designed for full control of any of the STINGER batch and continuous feeders.

Hazardous area control packages are also available.

The Young Industries, Inc. - BULLETIN 270-200 -

®

®

Options Available Model 1 Feeder Hopper Model 2 Feeder Hopper

Standard Hopper Size 9”, 12”, 18”, 24”, 36” Square 18”, 24”, 36”, 48”, 60”, 72”, 96” Diameter,

Standard Hopper Capacity .33 cu. ft. to 30 cu. ft. 3 cu. ft. to 500 cu. ft.

Custom Hopper Size Minimum - .33 cu. ft.Maximum size - 40 cu. ft.

Minimum - 2 cu. ft.Maximum - As needed

Scale Capacity 30 lbs. to 5,000 lbs Minimum - 100 lbs.Maximum - As needed

Feed Tube Size - Standard 1.00” to 6.00” 1.00” to 6.00”

Feed Tube Size - Custom As needed As needed

Electrical Requirements 110v to 220v, 50-60 hz, 1 ph. input 110v to 220v, 50-60 hz, 1 ph. input

Materials of Construction Painted Carbon Steel304 Stainless Steel WPC

316 Stainless Steel

Painted Carbon Steel304 Stainless Steel WPC316 Stainless Steel WPC

®Standard STINGER Feeders are shown on the right.

All feeders can be custom designed and configured beyond options listed below.

Contact us for more information.

Model 1 Stinger Feeder® Model 2 Stinger Feeder®

Design Features

Feed hopper & Feeder Tube Single piece uni-body construction for economical low-headroom design

Modular construction to allow maximum number of hopper & feed tube

configurations

Feed hopper pressure range Standard -.5 to +0.5 psiCustom -3 to +5 psi

Standard -1 to +3 psiCustom -30 to +150 psi

©Copyright The Young Industries, Inc. 2000 -2013

Specifications subject to change without notice The Young Industries, Inc. - BULLETIN 270-200 -

SEEING IS BELIEVING

Mobil Test ®STINGER

System Now Available for

a Visit to Your Plant

Mobile demonstration trailers are located throughout the United States making it easy to provide first hand knowledge about how the

®STINGER handles your materials. A unit can be quickly set up in any convenient plant location (Even in your parking lot). This will enable your key personnel to see the handle your ®STINGERpowder products; providing immediate answers. Demonstrations are free.

Give us a call at 800-546-3165 or email us at [email protected] to contact our Area Representative to schedule a visit.

Young Industries has been designing,

engineering, building and installing turnkey

batch weighing system for over 50 years.

These batching systems range from large

PVC compounding and chemical processing

facilities to individual paper bag loss-in-

weigh one ingredient systems.

The Young Industries Batching Systems

handles difficult-to- handling products like

titanium dioxide and other pigments.

If you are looking for highly accurate,

efficient and reliable equipment and

systems, contact us at

[email protected].

Fine tune your process with

product testing

Complete product testing facilities are available at our Muncy plant. Tests are conducted on your material by our trained Bulk Materials Handling Engineers and Technicians. You are welcome to view the demonstration of equipment at work on your own product.

For more information, call 570-546-3165 or fax 570-546-1888 or e-mail [email protected]

Number 270-401-1PRODUCT SPECIFICATION SHEET

® Model ST-2 STINGER Feeder Page 1 of 2


www.younginds.com

APPLICATION: Fast batch weighing of fine difficult to handle materials without the use of any moving parts.

DESIGN FEATURES: Compact, economical design combines feeder tube support

frame and hopper into one weldment Highest turn down rate (500:1) for reducing your process

time. Batch Accuracy up to +/- .1 Lbs. Standard inlet to discharge lengths from 1' to 10', longer

lengths are also available as options Wide range of standard hopper sizes Feed rates up to 30,000 lbs./hr. provide fast accurate batches Feeder Tube features Young Industries STINGER®

Technology

STINGER Feed Hopper features a built in Young Industries ®

SilentFlow Discharger that conditions material without any ®

moving parts or vibration Available in NEMA 4 or Explosion Proof designs

UNIQUE DESIGN QUALITIES: No Auger means no moving parts to wear out or replace Low energy costs No safety hazards common to screw augers No vibration to disrupt scale No bearings or motors to maintenance or replace Minimal maintenance Dependable service


The Young Industries, Inc. PRODUCT SPECIFICATION SHEET 270-401-1 Page 1

®STINGER Feeder Model 1 with ST Feeder Tube

FEED RATES:

Note: Feed rates will vary based on feeder configuration and material properties.

Approximate capacities listed below

Feeder Tube Size Maximum Capacity

Inches mm Lbs/hr Kg/hr

1.50 38 2,400 1.091

2.00 51 4,000 1,818

3.00 76 8,000 3,636



4.00 102 16,000 7,273

5.00 127 24,000 10,909

6.00 152 30,000 13,636

A FEW OF THE COMMON MATERIALS HANDLED: - Adipic Acid - Carbon Black - Fly Ash - Metal Powders - Powdered Sugar- Aluminum Oxide - Ceramic Powders - Fumed Silica - Sodium Bicarbonate - Pigments - Antomite - Corn Flour - Iron Oxide - Powdered Minerals - Spices- Borax - Clays - Lime - Polymers - Titanium Dioxide (all grades)- Calcium Carbonate - Dextrose - Magnetite - Powdered Ceramics - Zinc Oxide

FEED HOPPER:

STINGER Feed Hopper with built in SilentFlow Discharger conditions material and discharges it into the feeder tube without the use of ® ®

any moving parts or vibration Features: Standard hopper capacities range from .3 to 30 cu. ft. (8.5 to 850 liters) Standard hopper sizes range from 12" to 36" square. Removable covers available in carbon steel or stainless steel SUPPORT FRAME: Skirt supported for compact low head room design Hanging mount frames are available as a special option SCALE: Precision platform type scale for stable accurate weighing Available in carbon steel or stainless steel Standard scale capacities range from 30 to 5,000 lbs. (13.6 kg. to 23.272 kg.) Note: Actual scale capacity needed is based on material bulk density and feeder configuration

Specifications subject to change without notice

®

The Young Industries, Inc. - PRODUCT SPECIFICATION SHEET 270-401-1 Page 2©Copyright The Young Industries, Inc. 2000 - 2013

Page 2 of 2


® Model ST-1 STINGER Feeder


www.younginds.com


TEMPERATURE RANGE: Scales are temperature compensated from 14º F to 104º F (10º C to 40º C)

COMPRESSED AIR/GAS USAGEPressure: 10 to 30 psig Volume:

Feeder Size Flow Rate

12” 5 - 12 SCFM

18” 11 - 25 SCFM

24” 20 - 50 SCFM

36” 36 - 90 SCFM

Usage dependent on feeder hopper, tube size and materials handled

DRIVE:

Because the "ST-1" STINGER Feeder uses STINGER ® ®

Technology and is capable of making fast, accurate, consistent weighments without any moving parts, there is no need for a drive system or a motor. This smart, economical design not only saves money through reduction in spare parts but also results in savings of reduced utility and maintenance costs.

MATERIALS OF CONSTRUCTION: Per customer order requirements, available options include:

Housing: Option 1: Painted Carbon Steel Exterior with bare metal

interior Option 2: 304 WPC Stainless Steel Option 3: 316 WPC Stainless Steel

Note: All interior TransFlow lined surfaces constructed of 316 ®

Stainless Steel Standard. Hopper Cover: Removable sizes 12" to 36" square Standard Construction of High Density Polyethylene (HDPE) Support Frame: Option 1: Painted Carbon Steel Option 2: 304 Stainless Steel

Feeder Tube: Standard - 304 Stainless Steel Housing with 316 Stainless

Steel TransFlow Fluidizing Media ®

Option 1: Carbon Steel Housing with 316 Stainless Steel

TransFlow Fluidizing Media ®

Option 2 - 316 Stainless Steel Housing with 316 Stainless


Assembly Hardware Standard: Plated Carbon Steel Optional : 8-18 Stainless Steel

INTERIOR PRESSURE: Operates at ambient pressure Standard Design Pressure - 10" W.C. Custom Design Pressure up to 150 PSIG

TECHNICAL DATA: CONTROLS: The Young Industries Model ST-1 Feeder is suitable for use in loss-in-weight or gain-in-weight batch applications. The controls package determines the actual feeder package operation. Our family of Young Industries TOUCHSTONE™ controllers are

designed to work seamlessly with each of our STINGER ®

Feeders. Customers may choose a suitable Batch, Continuous, control to meet your feeder and specific application needs.

Standard TOUCHSTONE™ features include: Ships pre-configured for quick setup NEMA 4 enclosure with optional upgrade to explosion proof

enclosure Features Quick Disconnect Electrical Fittings for quick and

easy maintenance ELECTRICAL AREA CLASSIFICATIONS:Standard NEMA 4 Optional NEMA 4XOptional NEMA 7/9 POWER REQUIREMENTS: TOUCHSTONE™ controls: Universal input voltage accepts 110 - 220Volts, 50/60hz single phase electrical supply. Instrument power: Standard 24VDC

Removable Cover

Inlet Connection

Vent Connection

Low Profile Scale

Removable Discharge Elbow

Hopper with Removable Skirt Cover

Hopper with Removable Skirt Cover

®Model 1 STINGER Feeder with ST Feeder Tube


®

Easily removable auger and drive assy


® Model STS-1 STINGER Feeder Page 1 of 2

APPLICATION:

Loss-in-weight, Gain-in-weight Batch Feeding, Continuous

Gravimetric Feeding or Volumetric Feeding of fine cohesive

powders and difficult to handle materials.

A FEW OF THE COMMON MATERIALS HANDLED: Adipic Acid - Carbon Black - Fly Ash - Metal Powders - Powdered Sugar- Aluminum Oxide - Ceramic Powders - Fumed Silica - Sodium Bicarbonate - Pigments - Antomite - Corn Flour - Iron Oxide - Powdered Minerals - Spices- Borax - Clays - Lime - Polymers - Titanium Dioxide (all grades)- Calcium Carbonate - Dextrose - Magnetite - Powdered Ceramics - Zinc Oxide

FEED RATES: Note: Feed rates will vary based on feeder configuration and material properties. Approximate capacities listed below


www.younginds.com

DESIGN FEATURES:

Compact, economical design combines feeder tube, support

frame and hopper into one weldment

Conveys materials without the high horsepower needs often found with other feeders

Batch Accuracy up to +/- .1% typ. at 2 sigma.

Standard inlet to discharge lengths up to 60".

Feed rates up to 800 cubic feet per hour

Feeder Tube features Young Industries' Patented STINGER ®

Screw Technology STINGER Feed Hopper features a built in Young Industries ®

SilentFlow Bin Discharger that conditions material without ®

any moving parts or vibration

Available in NEMA 4 or Explosion Proof designs

UNIQUE DESIGN QUALITIES:

Quick auger removal in minutes without the need for any tools

Bearing housing includes a purged, double-lip shaft seal which separates material from bearings and provides maximum bearing life

Young Industries Feeder tube conditions material ®STINGERafter it leaves the feed hopper

STINGER Feed Hopper features Young Industries ®

SilentFlow Bin Discharger conditions material without any ®

moving parts or vibration

® ®Model 1 STINGER Feeder with STS STINGER Tube



Feeder Tube Size Capacity

Inches mm 3ft /hr Liters/hr

1.00 25 .08 - 4.3 2.3 - 121

1.50 38 8 - 11 28.3 - 312

2.00 51 2 - 30 57 - 850

3.00 76 7 - 100 198 - 2,832



4.00 102 17 - 250 481 - 7,080

5.00 127 26 - 400 736 - 11,330

6.00 152 50 - 800 1,416 - 22,654

FEED HOPPER:

STINGER Feed Hopper with built in SilentFlow Discharger conditions material and discharges it into the feeder tube without the use of ® ®

any moving parts or vibration Features: Standard hopper capacities range from .3 to 30 cu. ft. (8.5 to 850 liters) Standard hopper sizes range from 12" to 36" square. Removable covers available in painted carbon steel or stainless steel SUPPORT FRAME: Skirt supported for compact low head room design Hanging mount frames are available as a special option SCALE: Precision platform type scale for stable accurate weighing Available in carbon steel or stainless steel Standard scale capacities range from 30 to 5,000 lbs. (13.6 kg. to 2,272 kg.) Note: Actual scale capacity needed is based on material bulk density and feeder configuration


®


Page 2 of 2


® Model STS-1 STINGER Feeder


www.younginds.com


Concentric Drive Option

TECHNICAL DATA: MATERIALS OF CONSTRUCTION: Per customer order requirements, available options include:

Housinjg: Option 1: Painted Carbon Steel Exterior with bare metal

interior Option 2: 304 Stainless Steel Option 3: 316 Stainless Steel Standard Cover: 18" to 36" dia. sizes: Removable cover Constructed of light weight High Density Polyethelyne

(HDPE) Support Frame (If Required): Option 1: Painted Carbon Steel Option 2: 304 Stainless Steel

Feeder Tube: Standard: 304 Stainless Steel Housing with 316 Stainless

TransFlow Fluidizing Media Option 1: 316 Stainless Steel Housing with 316 Stainless

Steel TransFlow Fluidizing Media Auger: Option 1: Replaceable High Density Polyethelyne

flighting on rigid 304 Stainless Steel Hex Shaft Option 2: 304 Stainless Steel Option 3: 316 Stainless Steel Assembly Hardware Standard: Plated Carbon Steel Optional : 8-18 Stainless Steel

COMPRESSED AIR/GAS USAGEPressure: 10 to 30 psig

Air or gas volume dependents on feeder hopper, tube size and materials handled.

CONTROLS: The Young Industries Model STS-2 Feeder is suitable for either Batch Feeding, Continuous Gravimetric Feeding, or Volumetric Feeding.The controls package set up determines the actual feeder package operation. Our family of Young Industries TOUCHSTONE™ controllers are designed to work seamlessly with each of our Feeders. Customers may choose a ®STINGERsuitable Batch, Continuous, or Volumetric control system to meet your specific application needs.

Standard TOUCHSTONE™ features include: Ships pre-configured for quick setup. NEMA 4 enclosure with optional upgrade to explosion proof

enclosure. Features Quick Disconnect Electrical Fittings for quick and

easy maintenance. See Product Specification Sheet No. 270-405-1 for more information.

ELECTRICAL AREA CLASSIFICATIONS: Standard NEMA 4 Optional NEMA 4X Optional NEMA 7/9 POWER REQUIREMENTS: TOUCHSTONE™ controls: Universal Input Voltage accepts

120-220 V/50-60hz, single phase electrical supply. Instrument power: Standard 24V DC DRIVE:Motor: Option 1: 1/8 - 5 HP, 230/460 Volts,3 ph, 50 -60 Hz. Option 2: 1/16 - 2 HP, 90 or 180 Volts, DC Motor. Option 3: Stepper Motor, NEMA 4 or NEMA 7/9. ** Explosion proof and wash down rated motors are also available as special options. Contact Young Industries for further information. Gear Reducer Orientation: Option 1: Right Angle Drive Option 2: Concentric Drive Standard features - Neither drive is orientation specific and can be located where needed in 90 degree increments.

TEMPERATURE RANGE:Scales are temperature compensated from 14º F to 104º F (10º C to 40º C)


12” 5 - 12 SCFM

18” 11 - 25 SCFM

24” 20 - 50 SCFM

36” 36 - 90 SCFM

Inlet Connection

Removable Cover

Vent Connection

Low Profile Scale

Removable Discharge Elbow

Hopper with Removable Skirt

Right Angle Drive

STS Feed Tube withQuick Disconnect Air Fittings

Model 1 STINGER Feeder with STS Feeder Tube®


®


® Model ST-2 STINGER Feeder Page 1 of 2

A FEW OF THE COMMON MATERIALS HANDLED: - Adipic Acid - Carbon Black - Fly Ash - Metal Powders - Powdered Sugar- Aluminum Oxide - Ceramic Powders - Fumed Silica - Sodium Bicarbonate - Pigments - Antomite - Corn Flour - Iron Oxide - Powdered Minerals - Spices- Borax - Clays - Lime - Polymers - Titanium Dioxide (all grades)- Calcium Carbonate - Dextrose - Magnetite - Powdered Ceramics - Zinc Oxide


www.younginds.com

APPLICATION: Fastest batch weighing of fine difficult to handle materials without the use of any moving parts.

DESIGN FEATURES: Modular design provides easy, economical configurations

that best suits your needs. No motors or moving parts are needed to condition or

convey material. Highest turn down rate (500:1) for reducing your process

time. Batch Accuracy up to +/- .1 Lbs. Standard inlet to discharge lengths from 1' to 20'. Longer

lengths are also available as options. Wide range of standard hopper sizes Feed rates up to 50,000 lbs./hr. provide fast accurate

batches®

Feeder Tube features Young Industries STINGER Technology

® STINGER Feed Hopper features a built in Young Industries

®SilentFlow Discharger that conditions material without any moving parts or vibration


UNIQUE DESIGN QUALITIES: No Auger means no moving parts to wear out or replace Low energy costs No safety hazards common to screw augers No vibration to disrupt scale No bearings or motors to maintenance or replace Minimal maintenance Dependable serviceModel 2 STINGER Feeder with ST Feeder Tube®



FEED RATES:

Note: Feed rates will vary based on feeder configuration and material properties.

Approximate capacities listed below



1.50 38 3,600 1,636

2.00 51 6,000 2,727

3.00 76 12,400 5,636



4.00 102 24,000 10,909

5.00 127 36,000 16,364

6.00 152 50,000 22,727

FEED HOPPER: ® ®STINGER Feed Hopper with built in SilentFlow Discharger conditions material and discharges it into the feeder tube without the use of

any moving parts or vibration. Features: Standard hopper capacities range from 1 to 500 cu. ft. (27 to 14,160 liters) Standard diameters range from 18" to 96" Diameter (45.7 cm to 244 cm) Removable covers available in carbon steel or stainless steel Optional manway access hatch available for sizes 48” - 96” SUPPORT FRAME: Standard support frame with three rigid support legs providing sure footed design and maximum scale accuracy. Hanging mount frames are available as a special option SCALE: Three modules centered under load scale for stable accurate weighing Available in carbon steel or stainless steel Standard scale capacities range from 300 to 60,000 lbs. (136 kg. to 27,000 kg.) Note: Actual scale capacity needed is based on material bulk density and feeder configuration


®



Page 2 of 2


® Model ST-2 STINGER Feeder


www.younginds.com


TEMPERATURE RANGE: Scales are temperature compensated from 14º F to 104º F (10º C to 40º C)

COMPRESSED AIR/GAS USAGEPressure: 10 to 30 psig Volume:

Usage dependent on feeder hopper, tube size and materials handled

DRIVE: (Not Required)

Because the "ST-2" STINGER Feeder uses STINGER ® ®

Technology and is capable of making fast, accurate, consistent weighments without any moving parts, there is no need for a drive system or a motor. This smart, economical design not only saves money through reduction in spare parts but also results in savings via reduced utility and maintenance costs.


18” 4 - 11 SCFM

24” 8 - 21 SCFM

36” 20 - 50 SCFM

48” 35 - 90 SCFM

60” 56 - 150 SCFM

72” 80 - 200 SCFM

96” 140 - 400 SCFM

®Model 2 STINGER Feeder with ST Feeder Tube

TECHNICAL DATA: MATERIALS OF CONSTRUCTION: Per customer order requirements, available options include: Feed Hopper: Option 1: Painted Carbon Steel Exterior with bare metal

interior Option 2: 304 WPC Stainless Steel Option 3: 316 WPC Stainless Steel

Note: All interior TransFlow lined surfaces constructed of ®

316 Stainless Steel Standard. Hopper Cover: Removable cover for sizes 18" to 36" diameter.of High

Density Polyethylene (HDPE) Welded cover with hatch for 48” to 96” diameter sizes. Support Frame: Option 1: Painted Carbon Steel Option 2: 304 Stainless Steel

Feeder Tube: Standard - 304 Stainless Steel Housing with 316 Stainless


Option 1: Carbon Steel with 316 Stainless Steel

TransFlow Fluidizing Media ®

Option 2 - 316 Stainless Steel Housing with 316 Stainless


Assembly Hardware: 8-18 Stainless Steel

INTERIOR PRESSURE: Operates at ambient pressure Standard Design Pressure - 10" W.C. Custom Design Pressure up to 150 PSIG

CONTROLS: The Young Industries Model ST-2 Feeder is suitable for use loss-in-weight or gain-in-weight batch applications. The controls package determines the actual feeder package operation. Our family of Young Industries TOUCHSTONE™ controllers are designed to work seamlessly with each of our

STINGER Feeders. Customers may choose a suitable batch, ®

continuous, control to meet your feeder and specific application needs.



easy maintenance

ELECTRICAL AREA CLASSIFICATIONS:Standard NEMA 4Optional NEMA 4XOptional NEMA 7/9 POWER REQUIREMENTS: TOUCHSTONE™ controls: Universal input voltage accepts 110 - 220Volts, 50/60hz single phase electrical supply. Instrument power: Standard 24V DC

Removeable Cover

Feed Hopper

Load Cells

SUPPORT FRAME

ST Feeder Tube


®


® Model STS-2 STINGER Feeder Page 1 of 2


www.younginds.com


The Young Industries, Inc.PRODUCT SPECIFICATION SHEET 270-404-1 Page 1

FEED HOPPER: STINGER Feed Hopper with built in SilentFlow bin discharger conditions material and discharges it into the Feeder Tube without the ® ®

use of any moving parts or vibration Features: Standard hopper capacities range from 1 cubic foot to 500 cubic feet Standard diameters range from 18" diameter to 96" diameter Low headroom designs available Sizes 18" diameter to 36" diameter feature removable covers Removable covers are available in carbon steel or stainless steel Sizes 48" - 72" diameter feature optional manway/access hatch SUPPORT FRAME: Standard support frame with three rigid support legs provide sure footed design and maximum scale accuracy Note: Hanging

mount frames are available as a special option SCALE: Consists of three modules centered under load for stable accurate weighments Available in carbon steel or stainless steel Standard scale capacities range from 300 lbs. to 60,000 lbs. (136 kg. to 27,000 kg.) Note: Actual scale capacity needed is based on material bulk density and feeder configuration

APPLICATION:

Loss-in-weight, Gain-in-weight Batch Feeding, Continuous

Gravimetric Feeding or Volumetric Feeding of fine cohesive

powders and difficult to handle materials.

A FEW OF THE COMMON MATERIALS HANDLED: - Adipic Acid - Carbon Black - Fly Ash - Metal Powders - Powdered Sugar- Aluminum Oxide - Ceramic Powders - Fumed Silica - Sodium Bicarbonate - Pigments - Antomite - Corn Flour - Iron Oxide - Powdered Minerals - Spices- Borax - Clays - Lime - Polymers - Titanium Dioxide (all grades)

FEED RATES: Note: Feed rates will vary based on feeder configuration and material properties. Approximate capacities listed below

Easily removable auger and drive assy

DESIGN FEATURES:

Modular design provides easy, economical configurations that best suits your needs

Conveys materials without the high horsepower needs often found with other feeders

Batch Accuracy up to +/- .1% typ. at 2 sigma.

Standard inlet to discharge lengths up to 96".

Feed rates up to 800 cubic feet per hour

Feeder Tube features Young Industries' Patented STINGER ®

Screw Technology STINGER Feed Hopper features a built in Young Industries ®

SilentFlow Bin Discharger that conditions material without ®

any moving parts or vibration


UNIQUE DESIGN QUALITIES:

Quick auger removal in minutes without the need for any tools

Bearing housing includes a purged, double-lip shaft seal which separates material from bearings and provides maximum bearing life

Young Industries Feeder tube conditions material ®STINGERafter it leaves the feed hopper

STINGER Feed Hopper features Young Industries ®

SilentFlow Bin Discharger conditions material without any ®

moving parts or vibration

®Model 2 STINGER Feeder with STS Feeder Tube



1.00 25 .08 - 4.3 2.3 - 121

1.50 38 8 - 11 28.3 - 312

2.00 51 2 - 30 57 - 850

3.00 76 7 - 100 198 - 2,832



4.00 102 17 - 250 481 - 7,080

5.00 127 26 - 400 736 - 11,330

6.00 152 50 - 800 1,416 - 22,654


®

©Copyright The Young Industries, Inc. 2000 - 2013

Page 2 of 2


® Model STS-2 STINGER Feeder


www.younginds.com



Right Angle Drive Option

Feeder Size Air Volume

18” 4 - 11 SCFM

24” 8 - 21 SCFM

36” 20 - 50 SCFM

48” 35 - 90 SCFM

Feeder Size Air Volume

60” 56 - 150 SCFM

72” 80 - 200 SCFM

96” 140 - 400

TECHNICAL DATA: MATERIALS OF CONSTRUCTION: Per customer order requirements, available options include: Feed Hopper: Option 1: Painted Carbon Steel Exterior with bare metal

interior Option 2: 304 Stainless Steel Option 3: 316 Stainless Steel Standard Hopper Cover: 18" to 36" dia. hopper sizes: 48" to 96" dia. Sizes: Fixed, welded cover with optional

access hatch Support Frame: Option 1: Painted Carbon Steel Option 2: 304 Stainless Steel

Feeder Tube: Standard: 304 Stainless Steel Housing with 316 Stainless

TransFlow Fluidizing Media Option 1: 316 Stainless Steel Housing with 316 Stainless

Steel TransFlow Fluidizing Media Auger: Option 1: Replaceable High Density Polyethelyne

flighting on rigid 304 Stainless Steel Hex Shaft Option 2: 304 Stainless Steel Option 3: 316 Stainless Steel Assembly Hardware: 8-18 Stainless Steel

COMPRESSED AIR/GAS USAGEPressure: 10 to 30 psig

Air or gas volume dependents on feeder hopper, tube size and materials handled.

CONTROLS: The Young Industries Model STS-2 Feeder is suitable for either Batch Feeding, Continuous Gravimetric Feeding, or Volumetric Feeding.The controls package set up determines the actual feeder package operation. Our family of Young Industries TOUCHSTONE™ controllers are designed to work seamlessly with each of our Feeders. Customers may choose a ®STINGERsuitable Batch, Continuous, or Volumetric control system to meet your specific application needs.



easy maintenance See Product Specification Sheet No. 270-405-1 for more

information

ELECTRICAL AREA CLASSIFICATIONS: Standard NEMA 4 Optional NEMA 4X, NEMA 7/9 POWER REQUIREMENTS: TOUCHSTONE™ controls: Universal Input Voltage accepts

120-220 V/50-60hz, single phase electrical supply. Instrument power: Standard 120V/60hz: Optional 24DC DRIVE: Motor: Option 1: 1/8 - 5 HP, 230/460 Volts,3 ph, 50 -60 Hz. Option 2: 1/16 - 2 HP, 90 or 180 Volts, DC Motor. Option 3: Stepper Motor, NEMA 4 or NEMA 7.

** Explosion proof and wash down rated motors are also available as special options. Contact Young Industries for further information.

Gear Reducer Orientation: Option 1: Right Angle Drive Option 2: Concentric Drive Standard features - Neither drive is orientation specific and can be located where needed in 90 degree increments

TEMPERATURE RANGE:Scales are temperature compensated from 14º F to 104º F (10º C to 40º C)

Hopper Cover

Feed Hopper

Load Cells

Support Frame

Concentric Drive

STS Feeder Tube

®Model 2 STINGER Feeder with STS Feeder Tube


®


®Touchstone™ STINGER Feeder Controller Page 1 of 2


www.younginds.com


The Young Industries, Inc.PRODUCT SPECIFICATION SHEET 270-405-1 Page 1

Standard STINGER Touchstone™ Feeder

Controller in a NEMA 4 Enclosure

User friendly graphics are shown on a 10.4” color touch

screen display.

Feeding Controls That Just Make Sense

®The Young Industries Touchstone™ STINGER Feeder

Controller provides user friendly displays that allow

operator to navigate easily without confusion.

Features Include:

Configurable, full color trend graphs

Rate Feed Running Trend Graphs

Rate Feed PID Loop Tuning Trend Variables

Standard hardware includes all the IO needed to

handle most standard applications with power in

reserve

Integrated configurable Alarms to alert the operator

Auto tolerance checking

Totalizer that keeps track of weight for all material

Networking Communication Options Include:

Ethernet via TCP/IP

CANbus

Modbus

Utility Requirements: Universal Supply Power accepts

100-240V/50-60hz

Standard Outputs: 24 Volts

HMI Display Resolution : 800 x 600 with a 10.4

Viewing Area and 65,536 colors (16 Bit Resolution)

Remote Control & Viewing Options Include:

- Send Email Alerts from PLC to specified email

address(s)

- “Remote Operator” feature allows HMI Screen to be

mirrored to any PC with access set to “Read Only” or

“Read/Write” Mode

- Ability to view defined variables and status updates

on remote PC via HTML Web Browser

Controller Screen Displays

True Rate History

When in rate feed mode, actual history screen provides true history of rate samples at 15, 30, and 60 seconds so you know exactly what rate your process is receiving at all times.


®

®


The Young Industries, Inc. PRODUCT SPECIFICATION SHEET 270-405-1 Page 2©Copyright The Young Industries, Inc. 2000 - 2013

Page 2 of 2


®Touchstone™ STINGER Feeder Controller


www.younginds.com


Rate Feed PID Tuning

Three stage auto PID loop tuning provides quick accurate feeding, easy setup and gets your process running with minimal setup.

Trend Graphing of PID Output Values

Visual trend graph shows health of Auto-PID loop tune to indicate whether your feeder is running at peak accuracy. This allows user the option to tweak PID Values to increase accuracy without the guess work.

Micro-SD Card Logging

®Every YI Touchstone™ STINGER feeder control system is equipped with a Micro-SD card capable of recording the last 30 days of continuous rate feed operation. The information is logged in one second intervals or the results of the last 1,500,000 batches.

Batch History Log

When in batch feed mode, the batch history screen records the results of the last 200 batches so they can be viewed on screen at anytime.

Easy Configuration

Well organized menus protected via password allows easy configuration and settings changes without the worry of unauthorized changes.

Remote Operator

®Every Yi Touchstone™ STINGER Feeder control panel can be remote monitored or controlled using remote operator

Built in Help Menus

Setup screens include help buttons that provide answers to common questions relating to the current screen. This approach gives you fast answers when you need them.

Controller Screen Displays


®

Gravimetric & Volumetric Feederss3.amazonaws.com/Younginds.info/Product Info/Website...

Documents

Transcript of Gravimetric & Volumetric Feederss3.amazonaws.com/Younginds.info/Product Info/Website...