Grandio Ascent EXTENSION KIT Manual April 14 2016
Transcript of Grandio Ascent EXTENSION KIT Manual April 14 2016
G R E E N H O U S E S GRANDIO
®
GREENHOUSE USER MANUAL© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved
April 14, 2016 Extendable Models
GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUALINCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION
Grandio Ascent 8x24 Shown In Image STOPThis manual is for
8x12, 8x16, 8x20 & 8x24.
If building an 8x8 with no extensions refer to
that manual.
G R E E N H O U S E S GRANDIO
®
Before you begin, take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual on pages 66-75. The base kit parts list is at the front on page 12 and 13. The back door transformation kit parts list is on page 76.
Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and white film side faces inside green-house. Panels may scratch easily so be careful what you clean them with.
Plan out when and where you are going to place the greenhouse, we recom-mend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.
Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day, plan to complete assembly in one day. Damage caused by incomplete assembly is not covered by warranty.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!
Save this owner’s manual for future reference and if you need our help.
CONTACT OUR CUSTOMER SERVICE DEPARTMENT at: 1-866-448-8231
Hours: 8:30a.m.-5:00p.m. Monday through Friday (Mountain Standard Time)
Backyard Living Source9543 W. Emerald St., Suite 101
Boise, ID 83704www.grandiogreenhouses.com
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY
Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choos-ing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come.
Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.
Cheers!Grandio Greenhouses
1
2
IMPORTANT! SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instruc-tions and identify all parts using the hardware identifier and parts list on pages 67-76. Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.
CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective �lm adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners.
• Each of the polycarbonate panels have a clear �lm side that should always face the sun, and a white �lm side which faces inside. The clear side has a UV coating and we recommend marking a small “x” on a corner of each panel to determine which side has the UV Coating as you cannot visually determine with your eye in the case of future disassembly.
• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.
• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.
• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.
• If using a ladder during assembly, use extreme caution.
• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a �rm and level base. If not properly installed warranty may be void.
NEEDED FOR ASSEMBLY • Tape Measure • 2 Step Ladders • Safety Glasses• Level • Work Gloves • Drill • Carpenter Square • Permanent Marker • Silicone Caulk• At Least 2 Adults • Masking Tape • Folding Utility Table
GRANDIO
T I PWhen you see this icon
pay special attention to
the helpful tips we have provided that will
make installation more e�cient.
G R E E N H O U S E S GRANDIO
®
ASSEMBLY INSTRUCTION STEPS
PREPARE FOR ASSEMBLY
STEP ONE: BASE ASSEMBLY
STEP TWO: FRONT ASSEMBLY
STEP THREE: BACK ASSEMBLY
STEP FOUR: MIDDLE ASSEMBLY
STEP FIVE: EXTENSION ASSEMBLY
STEP SIX: INTERIOR SUPPORT ASSEMBLY
STEP SEVEN: DOOR ASSEMBLY
3
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Ascent Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Assembly.............................................................21-26Back Assembly..............................................................27-31Middle Assembly.........................................................32-37Extension Assembly...................................................38-448x20 and 8x24 Extension Assembly.....................45-49Extension Assembly Continued.............................50-58Interior Roof Supports.....................................................59Door Assembly.............................................................60-65GRA-ASC-8A Parts List...............................................66-68GRA-ASC-8P Parts List......................................................69GRA-ASC-4X Parts List................................................70-72GRA-ASC-8XA Parts List.............................................73-74GRA-ASC-8XP Parts List....................................................75GRA-ASC-BD Parts List......................................................76Warranty.................................................................................77
93”2362 mm
72 1/16”1830 mm
42”1066 mm8X12
8X12
LEFT SIDE
FRONT WIDTH
RO
OF
PE
AK
HE
IGH
T
DO
OR
HE
IGH
T
DOOR
55 11/16”1414 mm
EA
VE
HE
IGH
T
PREPARE FOR GREENHOUSE ASSEMBLY
Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchor-ing options are acceptable, based on wind and ground conditions in your area.
Pre-read pages 11-20 for base kit assembly informa-tion.
Go to www.grandiogreenhouses.com for founda-tion ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together.
4
8X12 GRANDIO ASCENT A-FRAME STYLE GREENHOUSE DIMENSIONS
*SEE BASE KIT ASSEMBLY SECTION FOR ALL GREENHOUSE BASE DIMENSIONS ON PAGES 14-17.
Transparent Clear Film
Opal White Film
Polycarbonate Panels
Sun
The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.
IMPORTANT: POLYCARBONATE PANELS
IMPORTANT: BASE KIT ASSEMBLY & GREENHOUSE PLACEMENT
143 3/4”3652 mm
97 7/16”2475 mm
BASE 3 1/4”82.6 mm
1 3/4” / 44.4mmGUTTERS
EXTENSION KIT BOX CONFIGURATIONS
GRA-ASC-8P
Ascent 8’x8’
GRA-ASC-8A
+
Aluminum Extrusions, Hardware Bag, Front,
Back and Doors.
8x8 Base Kit
GRA-BAS-8
Polycarbonate Panels
Base kit & hardware
+
Ascent 8’x8’
GRA-ASC-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ASC-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Ascent 8’ Extension
GRA-ASC-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ASCENT 8X16
GRA-ASC-8XPPolycarbonate Panels For The 8’ Extension
+
Ascent 8’x8’
GRA-ASC-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ASC-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Ascent 8’ Extension
GRA-ASC-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ASCENT 8X20
GRA-ASC-8XPPolycarbonate Panels For The 8’ Extension
Ascent 4’ Extension
GRA-ASC-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-
ate Panels for 4’ Extension.
+ +
Ascent 8’x8’
GRA-ASC-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ASC-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Ascent 8’ Extension
GRA-ASC-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ASCENT 8X24
GRA-ASC-8PPolycarbonate Panels For The 8’ Extension
+
Ascent 8’ Extension
GRA-ASC-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRA-ASC-8XPPolycarbonate Panels For The 8’ Extension
Ascent 4’ Extension
GRA-ASC-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-
ate Panels for 4’ Extension.
Fron
t
Back
Fron
t
Back
Fron
t
Back
Fron
t
Back
5
We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site.*See the reference diagrams on pages 6-10 for more information about how the parts will go together and what makes up each section for the assembly. If building a back door you will follow the instructions in the manual, the parts for the transformation are in box GRA-ASC-BD.
GRANDIO ASCENT 8X12
Y4-1L08B
LEFT SIDE RIGHT SIDE
609
601A-B
604-L 604-R
622-L 622-R
601A-FL
609 609
601A-FR
609
622 622
601A-B
FRONT
L08A
610
L08B-X
601B 601B
607603C603A
601B 601B
L08D L08D
620 620
623A623A
623B 623B
619
L21
LEFT SIDE
610
602B602A
602A
602A
602B
L08C
603B/616
602B
L08C-X
L08C-X
615
RIGHT SIDE
603B/616
602A
602A
L08C-X
602B
L08C
602B
610
602A
L08C-X
602B
615
6
602C
L08B-X
602D
L08A-X
610 610
618 618
Y5
Y4-2 Y2-1Y2-2
Y1Y1
Y2-1
Y1
Y3-1 Y3-2Y9 Y9
Y6
Y7
Outside View
606-WS
606-WS
606-WS
606-WS
BA-S1
L08A-X
606-WS606-WS
603B
Y6
Y6
Y6
Y7
Y7
Y7
Y7
Y7
Y8Y8
BA-S2 BA-S2
606-WS
606-WS
606-WS
606-WSY6
Y6
Y6
Y6
Y5 Y5
Y5 Y2-2
Y1
606-WS 606-WS 606-WS606-WSY1Y1
DIAGRAM SHOWS THE ASSEMBLED(8’x8’ BASIC CONFIGURATION)
(GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 ASCENT KIT INCLUDES, FRONT,
BACK, BASE AND SIDES.
BA-S1
602D
603B603B
603B
L28L28
615
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08C
-XL08M
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
609
603B
/616
602A
602A
L08C
-X
602BL0
8C
602B
610 60
2A
L08M
-X
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
603B 60
4-L
604-
R
622-
L62
2-R
601A
-FL
601A
-FR
622
62260
3C60
3A60
1B60
1B
L08D
L08D
620
620
623A
623A
623B
623B
619
L21
L08A
-X
Y5Y2
-1
Y1
Y3-1
Y3-2
BA-S
1
L08A
-X
606-
WS
606-
WS
603B
Y5Y5
Y5Y2
-2 Y1603B
609
601A
-B
609
601A
-B
L08A
610
L08B
L08B
-XL0
8B-X
601B
601B
602C
602D
602D
610
610
Y4-2
Y4-1
Y2-1
Y2-2
Y1Y1
606-
WS
606-
WS
606-
WS
606-
WS
Y1Y1
BA-S
1
609
603B
/616
602A
602BL0
8C
602B
610
L08C
-X
615
618
Y9
Y7 Y8
BA-S
4
606-
WS
606-
WS
Y6Y6
609
610
602B
602A
602A
602B
L08C
L08C
-X
Y7
606-
WS
606-
WS
Y6Y6
Y7BA
-S2
607
607
(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 Ascent Includes Front, Back, Base, and Sides
8x8 Ascent Side
FRO
NT
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ASC
-8A
and
GR
A-A
SC-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
BA
CK
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
(4’ Extensions Side) 4X Ascent Side(4’ Extension Side) (GRA-ASC-4X)
Ascent 4’ Side Extension Includes Base
Outside View
DIAGRAM SHOWS THE ASSEMBLED 8X12 GRANDIO ASCENT
THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS A 4 FOOT EXTENSION KIT
7
603B
603B
615
609
603B
/616
602A
602A
L08C
-X
602BL0
8C
602B
610 60
2A
L08M
-X
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
604-
L60
4-R
622-
L62
2-R
601A
-FL
601A
-FR
622
62260
3C60
3A60
1B60
1B
L08D
L08D
620
620
623A
623A
623B
623B
619
L21
L08A
-X
Y5Y2
-1
Y1
Y3-1
Y3-2
BA-S
1
L08A
-X
606-
WS
606-
WS
603B
Y5Y5
Y5Y2
-2 Y1603B601A
-B
L08A
L08B
-XL0
8B-X
601B
601B
603B
603B
L08B
602C
602D
602D
610
Y4-2
Y4-1
Y2-1
Y2-2
Y1Y1
606-
WS
606-
WS
606-
WS
606-
WS
Y1Y1
BA-S
1
601A
-B
617
617
609
603B
/616
602A
602A
602BL0
8C
602B
610 60
2A
L08C
-X
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08C
-XL08M
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08C
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
615
609
61060
9
Outside View
DIAGRAM SHOWS THE ASSEMBLED 8X16 GRANDIO ASCENT
THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS AN 8 FOOT EXTENSION KIT
(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 Ascent Includes Front, Back, Base, and Sides
(8’ Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8’ Side Extension includes Base
8x8 Ascent Side(8’ Extension Side) 8X Ascent Side
FRO
NT
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ASC
-8A
and
GR
A-A
SC-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
BA
CK
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
8
609
603B
/616
602A
602A
L08C
-X
602BL0
8C
602B
610
602A
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
604-
L60
4-R
622-
L62
2-R
601A
-FL
601A
-FR
622
62260
3C60
3A60
1B60
1B
L08D
L08D
620
620
623A
623A
623B
623B
619
L21
Y5Y2
-1
Y1
Y3-1
Y3-2
BA-S
1
L08A
-X60
6-W
S60
6-W
S
603B
Y5Y5
Y5Y2
-2 Y1
607
607
609
603B
/616
602A
602A
L08M
-X
602BL0
8C
602B
610 60
2A
L08M
-X
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
615
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08C
-XL08M
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08M
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
615
L08A
-X
603B601A
-B
L08A
L08B
-XL0
8B-X
L08B
602C
602D
602D
610
Y4-2
Y4-1
Y2-1
Y2-2
Y1Y1
606-
WS
606-
WS
606-
WS
606-
WS
Y1Y1
BA-S
1
601A
-B
609
61060
9
603B
603B
609
610
602B
602A
602A
602B
L08C
L08C
-X
Y7
606-
WS
606-
WS
Y6Y6
Y7BA
-S2
609
603B
/616
602A
602BL0
8C
602B
610
L08C
-X
615
618
Y9
Y7 Y8
BA-S
4
606-
WS
606-
WS
Y6Y6
602A
607
AZ1
AZ1
(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 Ascent Includes Front, Back, Base, and Sides
(8’ Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8’ Side Extension includes Base
AZ1
AZ1
(4’ Extensions Side) 4X Ascent Side
(4’ Extension Side) (GRA-ASC-4X)Ascent 4’ Side Extension
Includes Base8x8 Ascent Side
(8’ Extension Side) 8X Ascent Side
Outside View
DIAGRAM SHOWS THE ASSEMBLED 8X20 GRANDIO ASCENT
THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT
BA
CK
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
FRO
NT
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-A
SC-8
A a
nd G
RA
-ASC
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ASC
-8A
and
GR
A-A
SC-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
9
609
RIG
HT
SID
E
603B
/616
602A
602A
L08C
-X
602BL0
8C
602B
610
602A
602B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
604-
L60
4-R
622-
L62
2-R
601A
-FL
601A
-FR
622
622
FRO
NT
603C
603A
601B
601B
L08D
L08D
620
620
623A
623A
623B
623B
L21
Y5Y2
-1
Y1
Y3-1
Y3-2 L0
8A-X
606-
WS
606-
WS
603B
Y5Y5
Y5Y2
-2 Y1
607
607
609
603B
/616
602A
602A
L08C
-X
602BL0
8C
602B
610 60
2A60
2B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
602A
602B
615
609
LEF
T S
IDE
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08C
-X
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
615
L08A
-X
603B601A
-B
BA
CK
L08A
L08B
-XL0
8B-X
L08B
602C
602D
602D
610
Y4-2
Y4-1
Y2-1
Y2-2
Y1Y1
606-
WS
606-
WS
606-
WS
606-
WS
Y1Y1
BA-S
1
601A
-B
609
61060
9
603B
603B
609
610
602B
602A
602A
602A
602B
L08C
603B
/616
602B
L08M
-x
618
Y9
Y6
Y7
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6
Y7 Y7Y8
BA-S
2
615
607
DIAGRAM SHOWS THE ASSEMBLED 8X24 GRANDIO ASCENT
THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS (2) 8 FOOT EXTENSION KITS
8x8 Ascent Side(8’ Extension Side) 8X Ascent Side(8’ Extension Side) 8X Ascent Side(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8)
8x8 Ascent Includes Front, Back, Base, and Sides
(8’ Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8’ Side Extension includes Base
(8’ Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8’ Side Extension includes Base
AZ1
602A
L08M
-X
609
603B
/616
602A
602A
L08M
-X
602BL0
8C
602B
610 60
2A60
2B
615
618
Y9
Y7 Y7 Y7Y8
BA-S
2
606-
WS
606-
WS
606-
WS
606-
WS
Y6Y6Y6Y6
602B
AZ1
619
BA-S
1
Outside View
10
L08C
-XL0
8C-X
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Ascent Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Assembly.............................................................21-26Back Assembly..............................................................27-31Middle Assembly.........................................................32-37Extension Assembly...................................................38-448x20 and 8x24 Extension Assembly.....................45-49Extension Assembly Continued.............................50-58Interior Roof Supports.....................................................59Door Assembly.............................................................60-65GRA-ASC-8A Parts List...............................................66-68GRA-ASC-8P Parts List......................................................69GRA-ASC-4X Parts List................................................70-72GRA-ASC-8XA Parts List.............................................73-74GRA-ASC-8XP Parts List....................................................75GRA-ASC-BD Parts List......................................................76Warranty.................................................................................77
11
BASE KIT ASSEMBLY INSTRUCTIONSPre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure.
Be sure the orientation will allow for proper drainage in and around your greenhouse.
It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.
The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all.
Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your greenhouse in keeping the temperature up inside.
Extreme Wind Conditions: If you live in a windy location there is no way to build a 100% storm safe greenhouse, but there are a number of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condi-tion areas where wind is constant and extreme.
See our website GrandioGreenhouses.com for Extreme Weather Anchoring Kits and Moisture Control Kits to aid in protecting your green-house in the event of harsh weather conditions prior to beginning assembly.
It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants and keeping the temperature and air circulation to the max e�ciency.
You will need to choose an anchoring system prior to installation, see our website for options: www.GrandioGreenhouses.com
For Cement Base Installation: We recommend you use wedge style concrete anchoring bolts to secure your structure.
For Deck Base Installation: We recommend you use anchoring bolts to secure your structure.
For Earth Installation: We recommend you use the BA-A1 / L-BOLT anchoring system, and bury corner posts into the ground and seal into place with quickrete..
BA-S5
BA-S6
BA-C4
BA-S10
BA-S03
ML01
46 3/4 in / 1187 mm
46 3/4 in / 1187 mm
8 7/16 in / 214 mm
1/2 x 3/4
M6*14
NUT
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
2
2
16
16
BA-S1
BA-S2
BA-C3
BA-S03
ML01
W05
97 3/8 in / 2474 mm
94/4 in / 2394 mm
5 7/16 in 138 mm
M6*14
NUT
CLIPS
PARTS WILL BE FOUND IN (GRA-BAS-8) BOXTHAT MAKE UP THE 8’X8’ BASE KIT
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
2
4
28
28
9
BASE KIT PARTS LIST
12
PAR
TS
LIST
FO
R B
ASE
KIT
PARTS WILL BE FOUND IN (GRA-ASC-4X) BOXFOR THE 4’ BASE KIT EXTENSION
BA-S3
BA-S4
BA-C4
BA-S10
BA-S03
ML01
93 7/16 in / 2374 mm
93 7/16 in / 2374 mm
8 7/16 in /214 mm
1/2 X 3/4
M6*14
NUT
PARTS WILL BE FOUND IN (GRA-ASC-8XA) BOXFOR THE 8’ BASE KIT EXTENSION
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
2
2
16
16
BASE KIT PARTS LIST
13
PAR
TS LIST
FOR
BA
SE K
IT
BA-S2
BA-S2
BA-C3
BA-C3
BA-C3
1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.2 Attach the BA-S2 to the BA-S5 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S6 and the BA-S2. Go to page 18 for the next step.
BA-S5BA-S6
BA-C3
8x12 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-4X)
BA-C4
BA-C4
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
BA-C4
BA-S5 BA-S2
BA-S03ML01
14
STE
P O
NE
BA-S10
BA-S10143 3/4” / 3652 mm
97 7/16” / 2475 mm
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
BA-S2
BA-S2
BA-C3
BA-C3
BA-C4
BA-S3BA-S4
BA-C3
BA-C4
1.3 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1 See diagram . 1.4 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2. Go to page 18 for the next step.
8x16 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA)
BA-C3
15
STE
P O
NE
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
190 15/16” / 4849 mm
97 7/16” /
2475 mm
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S2BA-S2
BA-C3
BA-C3
BA-S3BA-S4
BA-C3
BA-C4
BA-C3
BA-C4
BA-S5
BA-S6
1.5 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.6 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2, then BA-S3 to BA-S5 and BA-S4 to BA-S6. Go to page 18 for the next step.
8x20 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA) AND (GRA-ASC-4X)
HOLE FOR ANCHOR
16
STE
P O
NE
BA-C4
BA-S5 BA-S2
BA-S03ML01
BA-C4BA-S10
BA-S10
BA-C4BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
237 5/8” / 6036 mm
97 7/16”
/ 2475 m
m
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
HOLE FOR ANCHOR
BA-S1
BA-S2
BA-S1
BA-S2
BA-C3
BA-C3
BA-S3
BA-S4
BA-C3
BA-C4
BA-C3
BA-S4
BA-S3
8x24 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA) AND (GRA-ASC-8XA)
1.7 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1. The BA-S3 will attach to the other BA-S3 and BA-S4 will attach to the other BA-S4 See diagram . 1.8 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01.See . Repeat for other side connecting the BA-S4 and the BA-S2, and then the BA-S3 to the BA-S3, and then the BA-S4 to the BA-S4. Go to page 18 for the next step.
17
STE
P O
NE
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-C4BA-S10
BA-S10
BA-C4BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
BA-C4 284 3/8”/ 7223 mm
97 7/16”
/ 2475 m
m
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
18
STE
P O
NE
1.9 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 Bolt and ML01 Collard Nut combo, tighten the collard nut on the inside of the base kit using the 10mm wrench. Repeat this process on all corners. See and . Note: BA-S1 will be the front and back, while the BA-S2’ s will be the sides of your greenhouse base.
1.10 For Ground Installation only Insert the BA-S03 and the BA-A1 into the holes at the bottom side of the corners of the base, the nut will be tightened on the inside of base, see and . Locate the anchoring devices for your installation needs and follow the directions for that anchoring system. If you have not purchased an anchoring system please go to www.GrandioGreenhouses.com for anchoring kit options.
BASE KIT ASSEMBLY INSTRUCTIONS
BA-S1
BA-S2
FRONT
SIDE
BA-C3
BA-S03ML01
BA-C3
BA-S1
BA-S2
BA-S03
ML01 Collared Nut
BA-S03
ML01 Collared Nut
BA-S03
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-S10
HOLE FOR ANCHOR
HOLE FOR ANCHOR
OutdoorGround
Assembly
1.11 If using an L-Bolt / BA-A1 anchoring kit the BA-A1 must be buried in ground. See .Dig holes to bury the BA-A1’s, you determine size and depth for your location. We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package.See www.GrandioGreenhouses.com for anchoring kit options.
BASE KIT GROUND INSTALLATION
BA-S2
BA-A1
BA-S1
BA-S03 BA-A1 * Must be inserted into the ground, and secured with concrete.
GRANDIO
T I PMake sure base is squared and level before setting
anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides.
**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
19
STE
P O
NE
20
STE
P O
NE
1.12 Holes are present in base kit for anchoring bolts see and . You determine and acquire proper fastener prior to installation for your surface. Discard the BA-S10 for deck or concrete slab installation.See www.GrandioGreenhouses.com for anchoring kit options.
Use lag boltor concrete anchors
to attach base. (Fasteners not included).
B
Deck or Patio
Assembly
Use an appropriate fastener to attach to your surface through these access holes.
BA-C4
BA-S6 BA-S2
BA-S03ML01
BA-S1
BA-C3
BA-S2
HOLE FOR ANCHORBOLT OR SCREW.
BASE KIT DECK INSTALLATION**BASE MUST BE LEVEL & SQUARE,
FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
GRANDIO
T I PMake sure base is squared and level before setting
anchors. Use a measuring tape to ensure all corners are the same. Use level on all four sides.
If surface is uneven you may wantto purchase large washers that will fit under the base and allow fasteners to go through to use as a shim for leveling the base kit.
This picture shows the inside view of front section fully assembled.All parts for this section will be found in boxes GRA-ASC-8A and GRA-ASC-8P.
We recommend that you assemble the front wall on a tarp.* If you purchased the Back Door Transformation kit you will repeat this section for your
back wall using parts found in GRA-ASC-BD, GRA-ASC-8A and GRA-ASC-8P boxes.If you want to purchase the Back Door Transformation kit call 1-866-448-8231.
601B
L08A-X
601B
Y3-2
603A
603C
L08D / 603B
L08A-X604-R
601A-FL601A-FR
Y3-1
Y1Y1604-L
619
W02 W02
W02TW02T
W01
W04
L08D / 603B
GRANDIO
T I PLay �at on ground to assemble the front frame of
your greenhouse. If possible try to �nd a shady area protected from the wind. Panels can burn grass and plants if in direct light.
GRANDIO
T I PWe recommend watching our how to assembly videos
with tricks and tips for easier assembly and installation of your Grandio Greenhouse at: www.grandiogreenhouses.com
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
Inside View606-WS 606-WS
21
STE
P T
WO
Y2-2 Y2-1
FRONT FRAME ASSEMBLYALWAYS ASSEMBLE FRONT HORIZONTAL
2.1 Use W01 bracket to attach the (2) 601B’s together with the 603C, secure parts with the S05 fasteners provided as shown in . Pre thread W01 fasteners with S05 for ease of installation, only turn a few times. Screw heads will remain outside channel.
2.2 Insert Y3-1 and Y3-2 window panels as shown in .
2.3 Attach 603C and 603A with W04 and S04/ML01 fasteners as shown in .
2.4 Attach W02T to 601B and 603A with the S04/ML01 fasteners as shown in , leave a bit loose to ease installation of next step.
Y3-1Y3-2
601B 601B
603A
603C
W01
W02TW02T
W04
Inside View
W01
601B601B
603C
S05
S04ML01
W04 603C
603A
S04/ML01W02T
603A
601B
Transparent Clear Film
Opal White Film
Polycarbonate Panels
Sun
The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assembly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.
IMPORTANT: POLYCARBONATE PANELS
22
STE
P T
WO
Inside View
IMPORTANT: Use only S05 Screws, other screws may damage frame.
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
*IF USING THE MOISTURE CONTROL KIT YOU WILL USE IT NOW
S04
ML01
604-R
619
601A-FL601A-FR
604-R 604-L
619
INSIDE DOOR FRAME
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
A
TIP: If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track.
S04
601A-FR
ML01619
2.5 View diagrams and attach the (2) 604‘s and (2) 601A’s to the 619 with the S04/ML01 nut and bolt combos. Note the orientation of the 601A-FR and 601A-FL and the holes that should be at the top of the piece and face to the front, see the diagram to the right. shows where the corner pieces attach to 619.
shows where the door frame attaches to the 619.
*If assemblling the back door you will need to drill 1/4” holes in 601A-B’s to match the front wall, these holes should face the ground during assembly.
INSIDE Inside View
Inside View
INSIDE
OUTSIDE
INSIDE OUTSIDE
INSIDE
OUTSIDEOUTSIDE
INSIDE
GRANDIO
T I PMake sure the hole on the 601A-FL and 601A-FR
face to the front of greenhouse for future install of the L21 and L28 bracket that holds the door header in place.
NOTE HOLESON 601A SHOULD FACE FRONT OF GREENHOUSE
23
STE
P T
WO
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
2.6 Attach 606-WS to 619, this will hold the polycar-bonate panels in place. If it seems too tight slide �ngers or nut driver along edges, gently stretching the 606-WS to allow room for panels to �t .
2.7 Insert Y1 polycarbonate panels into place, make sure Y1’s slide completely into 606-WS as shown in .
2.8 Set (2) 603B’s atop the Y1 panels, then attach (2) L08D’s to the 603B’s, 601A’s and 604’s using S04/ML01 fasteners, make sure it is snug with the tops of the Y1 panels, then tighten fasteners. See and .
2.9 Insert the Y2-2 and Y2-1 polycarbonate panels into the track of the 603B.
L08DL08D
Y1 Y1
604-L604-R
619 606-WS
606-WS
601A-FL
Polycarbonate panel
606
619
A
601A-FR
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
Inside View
OUTSIDE
A
S04/ML01
603B
L08D
601A-FR
604A-R
601A-FR 604-R603B
L08D
Y2-1Y2-2
603B 603B
24
STE
P T
WO
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
603A
601B
603C
601B
Y3-2 Y3-1
604-R
Y-1 Y-1
W02W02
601A-FL601A-FR 604-L
FAT END DOWN
S05W02T W02T
FAT END DOWN
Y2-2 Y2-1
W02
601B
FAT END
S05
W02
601B
601A-FR
S04ML01
W02T
604-R
601B603A
2.10 Move roof and front section together and align the W02’s into the 601A’s, and align the S04/ML01’s on the W02T’s into the 604’s. Insure a snug �t between the W02T’s, 601B’s and 601A’s and then tighten the S05 screws as shown in . Tighten the W02T’s with the S04 /ML01 nut and bolt as shown in .
25
STE
P T
WO
L08D L08D
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
2.11 Attach the (2) L08A-X ‘s to 601A’s and 604’s. See and .
2.12 To square front section loosen S04/ML01 attached to the tops of the (2) L08A-X’s, square the frame with carpenter square or use a measuring tape to make sure corner measurements are the same, tighten L08X’s to hold square-ness, L08A-X should be attached 1” up from bottom bolt see .
601B
L08D
L08A-X
601BY3-2
603C
L08D
L08A-X
604-R
601A-FR 601A-FL
Y3-1
Y1Y1604-L
619
W02 W02
W02TW02T
Y2-2 Y2-1
603A
GRANDIO
T I PSet front aside in a shaded area, do not lay on grass,
prolonged sunlight through the polycarbon-ate panels will burn if placed directly on top of plants during the intense sun of the day.
Use measuring tape to measure from corner to corner to assure square.
L08A-X601A-FR
S04/ML01
606-WS 606-WS
ML01 S04
L08A-X 619
26
STE
P T
WO
604-R
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
601B
L08B-X
601B
Y4-2
602C
L08B
L08B-X
602D
601A-B 601A-B
Y4-1
Y1Y1602D
W02 W02
Y1Y1
W01
L08A
W04-1 W04-1
603BY2-2 Y2-1
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
Inside ViewGRANDIO
T I PMake sure the UV coated side of the panel faces
outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
603B 603B603B
606-WS606-WS
27
STE
P T
HR
EE
BACK ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE BACK HORIZONTAL
This image shows the inside view of the back wall assembly.All parts for back assembly will be found in box GRA-ASC-8A and GRA-ASC-8P.
We recommend that you assemble the back wall on a tarp.* If you are using the Back Door Transformation Kit you will skip this section.
3.1 Prethread all S05 Screws into the W01 and W02’s, only turn a few times, see .
3.2 Use W01 bracket to attach the (2) 601B’s together as shown in diagram .
Attach (2) W02’s to the (2) 601B’s as shown in diagram .
3.3 Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram .
Attach (2) 602D’s to L08A using S04/ML01 fasten-ers as shown in diagram .
Attach 602C to L08A using S04/ML01 fastener as shown in diagram .
601B
601B
W01
601B601B
S05
L08A
W01
W02 W02
Inside View
601A-B602D602C602D601A-B
W02
601B
FAT ENDDOWN
602D
L08AINSIDEML01
601A-B
L08A
S04 INSIDE
ML01
S04
602C
L08A
W02 W02W01
FAT END
FAT END
28
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
602C 602D
L08B
603B 603B
602D
606-WS
L08A
Y1Y1
Y4-2 Y4-1
3.4 Attach (4) 606-WS’s to L08A as shown in diagram .Insert the Y1 polycarbonate panels into the grooves of 601A-B’s, 602D’s and 602C. Make sure Y1 panels are inserted into 606-WS as shown in .
3.5 Set (4) 603B’s on top of the Y1’s that are now in place. Attach L08B to (2) 601A-B’s, 602D’s and the 602C with S04/ML01 fasteners as shown in diagram , and , . Pre thread all fasteners into assigned channels and align with L08B for ease of installation.
3.6 Insert the Y2-1 , Y2-2, Y4-1 and Y4-2 poly-carbonate panels into place as shown in the diagram to the right.
Y1Y1
603B 603B
L08B602C
Polycarbonate Panel
606-WS
L08A
603CL08B
602CS04
ML01
L08B
601A-B
601A-B601A-B
Inside View
603B603B
Y2-1Y2-2
603B
602D
L08B
29
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
3.7 Attach the roof to the back wall use W01 fastener to 602C and the (2) W02’s to the (2) 601A-B’s using the S05 fasteners as shown in diagram and , pre thread all screws for easiest installation, tighten when flush with frame and square.
602C
601A-B601A-B
Y4-1Y4-2
Y1Y1 Y1Y1
W01
601B601B
S05
602C
W01
W02 W02
603B 603B W02
601B
601A-B
FAT ENDDOWN
Inside View
L08A
Y2-1Y2-2
603B603B
602D602D
30
STE
P T
HR
EE
L08B
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
L08B-X601A-B
ML01 S04
602D
L08B-X L08A
3.8A. Attach the W04-1 to the 602D and 601B with S04/ML01 fasteners as shown in .
B. Attach (2) L08B-X’s to (2) 602D’s and L08A with S04/ML01 as shown in .
C. Attach (2) L08B-X’s to the (2) 601A’s with fasteners as shown in .
L08B-X L08B-X
GRANDIO
T I PSquare by loosening bolts attached to the tops of the
L08B-X, use measuring tape to make sure corner to corner measures the same.
602D
601B
S04/ML01W04-1
Inside View
602D 602D
S04/ML01
31
STE
P T
HR
EEBACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
601A-B 601A-B
2
1
MIDDLE ASSEMBLY INSTRUCTIONS
GRANDIO
T I PYou will need a minimum of (2) people to complete the
middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
Warning: The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.
ML01/NUT
S04 BOLTW05CLIP
32
STE
P F
OU
R
BA-S2
601A-FR
ML01S04
Inside ViewFront Right side
BA-S1
**This Base shows a 8x12, your greenhouse may be longer and configured of more base kit pieces.
BA-S2
BA-S1 BA-S5
BA-S6
4.1 We recommend pre threading all (9) W05 Clips with the nut and bolt combos now. See , note the bolt head will always slide into the extru-sion, W05 clips will be used in step 4.5.
4.2 With no less than 2 people place the pre assembled front section on top of the base kit front. Have person (1) hold the front vertically while the other attaches the front section 601A’s to the base using S04/ML01 fasteners as shown in .Person (1) must continue to hold up the front wall!
If building a greenhouse with a front and back door you will repeat steps 4.1-4.5 for attaching both front and back walls of the greenhouse.
33
STE
P F
OU
R
MIDDLE ASSEMBLY CONTINUED
601A
601B
L08A-X
L08C-X L08D
L08C-X
Base
4.3 Attach L08C-X to 601A and the BA-S2 with (3) S04/ML01 on both sides as shown in and with the nut and bolt combos.4.4 Attach the front section 619 to the base using S10/ML02 fasteners as shown in , then attach the 619-BAR threshold support to the inside of the 619 with (5) S19 self tapping screws included in the package, see .
2
1
BA-S1
604
601A
601A619-BAR will attach with the (5) S19screws
619 Attaches to the base kit with S10/ML02
L08C-X
L08C-X
2
1
4.5 Have one person hold the front vertically while the other attaches the font section to the base with W05/S04/ML01 fasten-ers as shown in , and . The (4) W05 clips will catch the under edge of the front base kit and then slide upward attach-ing to the bottom of the 601A’s and the 604’s, you will switch out the S04/ML01 that was originally used to the W05 Clip Combo. If you are having a di�cult time at the corners tightening the ML01 �anged nuts you may switch to the ML02 non �anged nuts for easier installation.
BA-S1
BA-S2
BA-S1
604
601A-FL
601A-FR
BaseBA-S1
W05619
Inside
MIDDLE ASSEMBLY CONTINUED
BA-S5
BA-S6
34
STE
P F
OU
R
BA-S2
601A-FRML01S04
Inside View
W05
BA-S1
ML01 S04
L08A-X 619
604-R
W05
L08C-X
L08C-X602D
602D
602C
601A-B
35
STE
P F
OU
RMIDDLE ASSEMBLY CONTINUED
4.6 Attach back wall 601A-B’s with back base corners using S04/ML01 on both sides as shown in .
4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in . Attach the L08C-X to the 601A-B as shown in , make sure the S04/ML01 combos are tight.
4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A-B’s meet the corner of the base as shown in , and where 602D’s, and the 602C meet the BA-S1B see . Then use W05 Clip combos to attach the corner 601A’s to the base kit as shown in , you will switch out the S04/ML01 that was originally used to the W05 Clip Combo.
601A-B
601B
L08B-X
L08C-X L08B
W05
Base
602C, 602D
Outside
Inside
BA-S2 orBA-S6
601A-B
ML01S04
Inside ViewBack Left side
BA-S1
L08C-X
Base
Back Wall BA-S1601A-BML01S04
BA-S2 orBA-S6
Inside View
W05
Back Base
Back Base
If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then skip ahead to step 4.9.
601A-B
36
STE
P F
OU
R
Repeat these steps if you are building an 8x20 or 8x24 with your last extension box, note it is best to connect 8x8, then 8X, then an 4X if assembling an 8x20. Note that the notches shown in should be spaced every 2 feet, none should be right next to each other.
4.9 Attach the 607 to 607-4X or 608-8X extension with the 607-XS and the (4) S08 screws provided see , . The S08 screws are to be installed on the inside as shown in diagram . Wait to tighten the screws all at one time when both sections are aligned correctly, apply even pressure while tightening.
4.10 Apply a bead of silicone to the seam where the 607’s meet and to the holes where the S06 screws will attach the DP01 to the 607 ridge. See . Immediately align the DP01 apply a small amount of silicone to the holes on the exterior of DP01 then insert the S06 screws.
607-8X
607607-XS
For 8x20 and 8x24 Grandio Ascent Assembly
MIDDLE ASSEMBLY CONTINUED
607-XS
607-8X
607
DP01
FRONT
S08
WARNING
Notches
Notches
APPLY SILICONE CAULKTO RIDGE AND HOLES
S06
607
607-8X
FRONT
S06
DP01
MIDDLE ASSEMBLY CONTINUED
607
607
601B 601B
Inside View
Side Angle View
607
601B 601B
Inside View
S04/ML01
4.11 With 2 people, attach the ridge to front and back by sliding into place as shown in and , using S04/ML01 fasteners attach the 607 to the 601B’s. See for how the �nal orientation should be.
607
37
STE
P F
OU
R
607-4X
EXTENSION ASSEMBLY INSTRUCTIONS
Warning: You will need a minimum of 2 people to complete this section, you will not be able to stop assembly until page 44. Note that if you are assembling an 8x20 or an 8x24 greenhouse you will proceed thru the 2nd extension assembly instruc-tions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier.
GRANDIO
T I PBOLT INSTALLATION TIP: Locate about 30 nuts and
bolts and pre thread for easiest installation.
Warning: This section will take about 30 minutes to complete. Be prepared to �nish as there is not a stopping point until page 44 for an 8x12 or 8x16 or page 50 for an 8x20 or 8x24, depending on your greenhouse con�guration. Note it may be helpful to have a few more people at this point the more the merrier.
38
STE
P F
IVE
5.1 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.
5.2 Attach the 602A to the base with a nut and bolt combo where the extension kit meets on the base kit, with other person holding the 602A in place. Measure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .
5.3 Have one person keep holding the 602A and L08M-X on one side for support while you prepare for next step on the next page.
BASE
602A
6”
W14
602A
L08M-X W14
W14 BRACKET
EXTENSION ASSEMBLY INSTRUCTIONS
BA-S2
Measure 6”
602A
L08M-X
602A
607
Measure 6”
39
STE
P F
IVE
L08M-XL08M-X
Back
Back
Front IMPORTANT TO HAVE THE L08M-X
FACE THE BACK AS SHOWN
5.4 Attach the 609 to the (2) 609-XS’s with (4) of the S09 screws provided see and . The S09 screws are to be installed on the inside of the 609 and will tighten into the 609-XS as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled.
Pay special attention to the orientation of the 609, make sure the correct side faces down, see .
609
Profile View
Groove
EXTENSION ASSEMBLY INSTRUCTIONS
40
STE
P F
IVE
UP
609
609-XSFRONT
INSIDE VIEW
UP
S09
UPFRONT
OUTSIDE VIEW
609-XS
609
1
2
L08D L08C-X601A
LOOSENML01
Inside View
GRANDIO
T I PYou will need a minimum of (2) people to complete the
middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
EXTENSION ASSEMBLY INSTRUCTIONS
601B
1
2
L08C-X 601A
601A
L08C-X
601B
601B
602A
607
602A
609601B
41
STE
P F
IVE
601B
609
S04/ML01
L08C-XL08D
Inside View
601A
5.5 With 2 people proceed to install 609 in this order, note that 609 must be installed with groove side down see .
1. With one person holding the 609 level and in position have the other person loosen the top of the L08C-X and let it fall free, attach the 609 to the 601B using S04/ML01 (nut and bolt). See and .
2. Now move the loosened S04/ML01 (nut and bolt) currently attached to the L08C-X upward to secure the 609, 601A-F and L08C-X together as shown in .
3. Have assistant keep holding at the middle section . Turn to next page for detailed installation.
UP
601B
609
Profile View
Groove
601A
Note the line on the 609 that shows the exact placement of the 601B’s and the 601A’s when installedcorrectly.
2
1
42
STE
P F
IVE
L08C-X 601A
601A
L08C-X
601B
601B
602A
607
602A
609
609
4. Note the top of 602A should touch the line on the 609 for exact placement, see . Attach the 609 to the 602A with the S04/ML01 nut and bolt combos see diagram .
5. Repeat steps 1-4 on the other side see .
EXTENSION ASSEMBLY INSTRUCTIONS
OUTSIDE VIEW
602A
NOTE EXACT PLACEMENT OF THE 602A TO THE 609.
EXACTPLACEMENT LINE FOR 602A
FRONT
609
609INSIDE VIEW
609-XS
FRONT
S04/ML01
43
STE
P F
IVE
602A
607
602A
609
602B
2
5.6 With person 1 holding the 609 steady person 2 will attach the 602B’s between the 609 and 607 on both sides. See and .
EXTENSION ASSEMBLY INSTRUCTIONS
1
Outside View
609
ML01/S04
602B
Inside View
602A
602A
NOTE EXACT PLACEMENT OF THE 602A AND 602B TO THE 609.
FRONT
602B 609
44
STE
P F
IVE
602A
607
602A
609
AZ-1
AZ-1
BZ-1
2
1
5.7 Connect the AZ-1 with the W17 and included hardware, see . With two people attach the AZ-1 to the base and the lower 602A, see . Then attach the upper end to the mid roof line see . Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.
5.8 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s with S04/ML01 nut and bolt combos, see .
IF YOUR GREENHOUSE IS AN 8X12 OR 8X16 SKIP TO PAGE 50. IF YOURS IS AN 8X20 OR 8X24 PROCEED ON TO THE NEXT PAGE.
EXTENSION ASSEMBLY INSTRUCTIONS
AFTER COMPLETING STEP 5.9
602A
AZ-1
S02/ML01
INSIDE VIEW
W17 BRACKET
S02/ML01You will need to switch this bolt out to an S02
FRONT
AZ-1
ML01W17 BracketNote orientationof bracket
S02
(7mm gap edge will fitdown into base bottom)
10mm7mm
1
5.9 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.
5.10 Attach the 602A to the base with a nut and bolt comboMeasure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01. See and . Attach the assembled L08M-X’s to the W14 as shown in and .
5.11 Have one person keep holding the 602A and L08M-X on one side for support while you prepare for next step on the next page.
BASE
602A
6”
W14
Measure 6”
L08M-X
602A
Measure 6”602A
L08M-XL08M-X
W14 BRACKET
602AL08M-X W14
2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17
45
STE
P F
IVE
INSIDE VIEW
IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN
Back
Front
5.12 Attach the 609 to the (2) 609-XS’s with (4) of the S09 screws provided see and . The S09 screws are to be installed on the inside of the 609 and will tighten into the 609-XS as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled.
Pay special attention to the orientation of the 609, make sure the correct side faces down, see .
609
Profile View
Groove
2nd EXTENSION ASSEMBLY INSTRUCTIONS
46
STE
P F
IVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17
609
609-XSFRONT
INSIDE VIEW
UP
S09
UPFRONT
OUTSIDE VIEW
609-XS
609
609
Profile View
GrooveGRANDIO
T I PYou will need a minimum of (2) people to complete the
middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
5.13 With 2 people proceed to install 609 extension at the eave.
1. With one person holding the 609 level and in position have the other person attach the 609 to other end of the 609-XS as shown in .
2. With one person holding the 609 level and in position have the other person attach the 609 to the 602A using S04/ML01. See .
3. Repeat steps 1. and 2. on other side of the greenhouse.
2nd EXTENSION ASSEMBLY INSTRUCTIONS
1602A609
609
47
STE
P F
IVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17
609
609--4X-L or 609-8X-LINSIDE VIEW
609-XS
FRONT
S09
602A
NOTE EXACT PLACEMENT OF THE 602A TO THE 609.
EXACTPLACEMENT LINE FOR 602A
FRONT
609
1
2nd EXTENSION ASSEMBLY INSTRUCTIONS
5.14 Attach the (2) 602B’s between the 609 and 607 on both sides. See and .
Outside View
Inside View
602B
602A
602A
607
609
609
48
STE
P F
IVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17
602A
NOTE EXACT PLACEMENT OF THE 602A AND 602B TO THE 609.
FRONT
602B 609
609
INSIDE VIEW
FRONT
S04/ML01
609-4X-L609-8X-L
BACKS04/ML01
602A
602B
1
602B
602A
602A
607
609
609
2nd EXTENSION ASSEMBLY INSTRUCTIONS
AZ-1AZ-1
BZ-1602B
5.15 Connect the AZ-1 with the W17 and included hardware, see . With two people attach the AZ-1 to the base and the lower 602A, see . Then attach the upper end to the mid roof line see . Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.
5.16 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s with S04/ML01 nut and bolt combos, see .
49
STE
P F
IVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17
602A
AZ-1
S02/ML01
INSIDE VIEW
W17 BRACKET
S02/ML01You will need to switch this bolt out to an S02
FRONT
AZ-1
ML01W17 BracketNote orientationof bracket
S02
(7mm gap edge will fitdown into base bottom)
10mm7mm
5.17 With two people attach the 609 extension to 609-XS with the (4) S09 screws provided see and .
5.18 With person 1 still holding in place have person 2 loosen the L08C-X nut and bolt combo to attach the 609 into place, see .
Repeat these steps on other side of the greenhouse, see .
601B609
609
609
602A
607
602A
609
2
1
601A-B
609
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
50
STE
P F
IVE
601B
609
S04/ML01
L08C-XL08B
Inside View
601A
609FRONT
S04/ML01
609-4X-L or 609-8X-L
BACKS04/ML01
602A
FRONT
602B 609609-XS
BACK609-4X-L or 609-8X-L
INSIDE VIEW
OUTSIDE VIEW
S09
609
609
602A
607
602A
609
602A602A
602A
602A
602A
602A
L08C-XS04ML01BASE
Inside View
609
602A
Inside View
BA-S2
602A
Inside View
ML01/S04ML01/S04
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
51
STE
P F
IVE
5.19 Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the ML01 (nut) attached to the L08C-X and the base. See diagram .
1. Once the bottom of one L08C-X is loosened set the 602A onto the bolt of the L08C-X. Be sure the 602A is aligned and sitting �ush on top of the base kit. See for reference.
2. Hold the 602A in place and attach the top of the 602A to the 609 using S04/ML01 (nut and bolt). As shown in .
3. Repeat steps 1. and 2. on all four corners where the L08C-X ‘s meet the base kit.
4. Now attach the bottom of 602A to the Base using a S04/ML01 (nut and bolt) as shown in , and to the 609 with an S04/ML01 combo as is shown in .
5. Repeat step 4. on all places where a 602A should go. You may reference diagrams at front for your exact size.
Note: Where the L08C-X reattaches to the BASE and the 602A be sure to secure them tightly see .
Loosen only one L08C-X at a time.
L08C-X
L08C-X
SUN
616 615PC sheet
5.20 Assemble the roof window vents as shown below in and , using the Z02 screws attach the 615, 616, and 618’s with the Y8 panel as shown, be careful not to strip the screw heads. Pay attention to the Y8 panel, stickers face the sun, and that the frames are assembled according to images below.
5.21 Insert assembled window into the end of ridge of 607 and slide into position. See . Window positions are your discretion however, must be in the middle for support, do not place nearest the front or back, nor right next to each other as you will need a 602B support to keep in window vent in place. Place directly across from each other for best cross draft ventilation, see for optional placement. Attach the 602B’s as shown between and , after all roof vents are positioned.** It is recommended to apply silicone caulk to the exterior seams on the bottom and sides of each panel, where panels meet the frame for water resistance, or see the Moisture Control Kit on our website to maintain panel clarity. The interior and top of each panel is protected so it is recommended that you leave them un-caulked allowing the panels to breathe.
GRANDIO
T I PPlace roof windows in desired location before
attaching all 602B’s.
Y8
618
Z02
Z02
Z02
Z02
Z02618
Screwdriver Outside View
615
616
618616
Z02
Note Correct Orientation
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
616
618
615607
SUN
609
607
609
Y8
Y8602B
52
STE
P F
IVE
602B
602B
602B602B
Y8
Inside of window
606-WS
PC sheet
BASE GRANDIO
T I PMake sure the UV coated side of the panel faces
outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
602A
4.16 Install plastic strip 606 before inserting polycarbonate sheet Y7’s.
4.17 After Y7’s are installed, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is level. The top edges of Y7’s will align when greenhouse is level.
S04/ML01
L08C-X
609
Loosen
5.22 Install plastic strip 606-WS before inserting polycarbonate sheet Y6’s, see . Install all Y6 panels into the channel’s of the side walls, and �t down into the 606-WS.
5.23 After Y6’s are installed, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is plumb. The top edges of Y6’s will align when greenhouse is level or plumb. See .
OUTSIDE
Y9Y9
Y9
606-WS
BASE
Y6
Y6
Y6
Y6
Y6Y6
Y6Y6
Y6Y6
Y6Y6
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
53
STE
P F
IVE
5.24 To ensure there is no gap in roof vent position 603B as shown in . Connect 603B to middle of 602B’s using W04 bracket as shown in .
5.25 Attach HQC01 to 616 with the Z04 screws see , close roof vent and attach the handle onto HQC02 middle pin (the �rst two holes of the handle to the second and third pins of HQC02). Then attach HQC02 into 603B’s track with S04/ML01 (nuts and bolts), see .
603B
618
616
616
603B
616
Z04
HQC02
Y8
Y8
HQC01Handle
Note: If you are installing automatic roof vent openers follow those directions for correct installation.SAVE MANUAL OPENERS FOR WINTER SWITCHOUT.
HQC01Handle
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
HQC01Handle
Y8
Y8
Y8
54
STE
P F
IVE
Inside view of 603B603B
602BW04
603B
HQC02
HQC01Handle
ML01/S04
Inside View
1 2 3
Outside
insideInside
Outside607609-WS
609-WS
PC Sheet PC Sheet609-WS
PC Sheet
5.26 Attach 609-WS to the inner roof line of the 607 and on both top and bottom of 609 as shown in and .
GRANDIO
T I PNote that there are two parts labeled 609 &
609-WS, one is the gutter support, the other is a clip that �ts under poly- carbonate panels inside greenhouse.
609
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
55
STE
P F
IVE
607
609
609
Y8
Y8
5.27 Insert polycarbonate sheets Y7’s and Y9’s into the roof of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown in the diagram once the panels are in place.
5.28 Slide 610 Gutters into 609’s groove as shown in diagram . Repeat on both sides. Note the orientation of the gutters, the extension gutters will be at the back and the holes should align with gutter down spout holes see next page.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
Y7
Y9
Y8
Y7
Y7Y7
Y9
601B
601A
610
609
609
610
Gutter
Outside View
56
STE
P F
IVE
The two profiles should be flush at ends when installed correctly.
DP02B
DP02
610-4X-L or 610-8X-L
610
5.29 Apply a small amount of the silicone caulk to the seam where the 610 gutters meet, then attach the DP02 on the inside of the gutter and the DP02B will slide under the gutter and will rest above the 602A. Apply silicone to the holes where the S07 screws will attach the 610 gutters to the DP02 and DP02B. Note the DP02B has pre-tapped holes to accept the screws and hold tight. See diagram and .
Repeat these steps to assemble the additional set(s) for both sides of your greenhouse.Remove the tape from the panels you may have used to hold in place.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
DP02
610-4X-L or 610-8X-L
610
602A
602B
57
STE
P F
IVE
5.30 Attach end caps to the ridge and gutters on both front and back as shown below. Squeeze a small amount of rubberized silicone or construction adhesive into the ends of ridge (607) to secure pressure �t end caps (601). It is recommended to caulk any areas that may allow water penetration such as at the gutter end caps and at the base corners to seal against water as shown in .
5.31 It is recommended to apply silicone caulk to the seams where panels meet the frame for water resistance.
J602A-E
Z03
J602B-E
Z03
Z03
601
J602B-E
Z03
J602B-E
Z03
J602A-E Z03
J601
610
58
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
607
INTERIOR ROOF SUPPORT ASSEMBLY 6.1 Attach the BZ1’s to the roof line as shown in diagram with the S04/ML01. Use CZ1’s to support the interior wall at the eave using the S04/ML01. See diagram .
6.2 Use S04/ML01 to attach the L08C’s to 601B’s and 602B’s on the inside of roof midway between the roof and the gutters for additional roof support. See diagram .
6.3 Remove the L08M-X support combo, take apart and now and install to the sides of the AZ1 extension brace, see . Save the hardware and W14 bracket for possible future use or hang inside as a plant hanger clip.
BZ1
CZ1
L08C
Y8
Y8
Y8
Y8
CZ1
BZ1
602A
602B
602B
602B
L08C L08C
602B
602B
609
602B
59
STE
P S
IX
L08M-X
DOOR ASSEMBLY DIAGRAM
Z01622
Y5
Y5
622-R
UP
UP
Catch
620Z01
Z01
Z01
Z01
Z01
623B
623A622Side View
622
J08A
BottomView
623B
620
623A
J08A
J08A
622-R
UP
UP
Side View
622
J08A
BottomView
Inside View
60
STE
P S
EV
EN
J04OPTIONAL
This image shows the inside view of Right Door Assembly.All parts for door assembly will be found in box GRA-ASC-8A and GRA-ASC-8P.
Use the #2 head Phillips Screw Driver for installation.If you are using the Back Door Transformation kit you will repeat steps 7.1-7.11 to install the Back Door,
these parts will be found in box GRA-ASC-BD.
You may need to gently open the channel with a flat head srewdriver if screws are not going into place with ease.
623B
623A
622
J08A
BottomView
J08A
We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orienta-tion of what is inside verses outside and how the doors will hang on page 63-65. Make sure window panels face the right direction to the sun and note that the panels have predrilled holes for the handles to attach later and these need to be aligned with the lock mechanisms, you may have to drill these out if they are not visible. This will save you from assembling the wrong way. 7.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .7.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .7.3 Insert Y5 windows into position as shown in .
623B
Z01
620Z01
Z01623B
623A
622 620
623A
622
620
Y5
Y5
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
622
UP
UP
Side View
Inside View
DOOR ASSEMBLY
61
STE
P S
EV
EN
J04OPTIONAL
J08A
622
J08A
BottomView
Side ViewOf Top
* DoubleBall Catch
on the 622-L
622-L
UP
UP
Side ViewOf Bottom
7.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see .7.5 Attach the 622-R to the 623B, 623A and 620 using the Z01 screws as shown in .7.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up so doors will latch closed and slide properly .
Y5
Y5
623B
623A
620
622-R
Catch
Z01
Z01
Z01
622-R
Side ViewOf Top
* Catch on the 622-R
622-R
UP
UP
Side ViewOf Bottom
* Note the orientation of the 622-L and 622-R. Also make sure the right side is facing out on the Y5 polycarbonate panels.
Inside View622
DOOR ASSEMBLY CONTINUED
62
STE
P S
EV
EN
DOOR INSTALLATION7.7 Slide the (2) S02 bolts down the track of the L21 see , align with the holes on the 603A door header. With one person inside the greenhouse line up hanging door track L21 with door header 603A, move bolts on L21 to line up with bolt holes on door header 603A. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will now center on the front of the greenhouse and tighten the S02/ML01 combo.
S02
L21
1
2
603A
63
STE
P S
EV
EN
2
Side Profile View of L21 Hanging Track
Inside View
Track
S02SCREW
S04 S04S02
7.8 Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle.
7.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and .
DOOR INSTALLATION
Outside View Inside View
Top
Bottom
Side Profile View of Hanging Track
L21 L21
622-HNDL
622-HNDLNUT/BOLT
622-HNDL
622-HNDLNUT/BOLT
64
STE
P S
EV
EN
DOOR INSTALLATION
You may remove all stickers now with Goo Gone remover if needed. You are now finished with assembly!
J07
603A
L21
L28
S04/ML01
Top View
601A
S02
L28
S02
601A-FRML01
65
STE
P S
EV
EN
Top Profile View
7.10 Attach L28 to L21 with S04/ML01, and L28 to 601A with S02/ML01 as shown below in diagram and . Check that the L21 and L28’s are square. Attach (2) J07 to the ends of L21 see . The L28 should align square to the 601A.
7.11 Check that the door locks are snug, you may adjust them with screwdriver if needed as they can be tightened or loosened.
601A-B
601A-FL
601A-FR
601B
602A
602B
602C
602D
603A
603B
603C
604-R
604-L
606-WS
607
609-WS
609
610
615
616
618
619 PACK 619-BAR
S19 SCREWS10 / ML02
BZ-1
CZ-1
L08ANOTE THESE ARE
PACKED TOGETHER
L08B
52 1/2 in / 1334 mm BACK CORNERS
52 1/2 in / 1334 mm FRONT LEFT CORNER
52 1/2 in / 1334 mm FRONT RIGHT CORNER
57 1/8 in / 1451 mm CORNER ROOF
52 1/2in / 1334 mm
57 1/2 in / 1451 mm
87 1/4 in / 2216 mm
70 3/8 in / 1787 mm
47 5/16 in / 1201 mm
21 7/8 in / 555 mm
17 in / 431 mm
68 7/8 in / 1750 mm FRONT RIGHT
68 7/8 in / 1750 mm FRONT LEFT
21 3/4 in / 553 mmWINDOW SEAL
94 1/4 in / 2394 mm
21 5/8 in / 550 mmWINDOW SEAL
94 1/4” in / 2394 mm
94 3/8 in / 2397 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 3/4 in / 500 mm
94 1/4 in / 2394 mm40 in / 1015 mm
M4*10M6*16
23 5/8 in /600 mmROOF SUPPORT
19 11/16 in / 500 mmEAVE SUPPPORT
94 1/4 in / 2394 mm
94 1/4 in / 2394 mm
BLACK WINDOW SEAL
GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
1
1
4
6
6
1
2
1
8
1
1
1
14
1
22
2
2
2
2
4
1-6191-619 Bar
5 - S19 Screws3 - S10 / ML02
3
6
1
1
(GRA-ASC-8A) GRANDIO ASCENT 8’X8’ ALUMINUM PACKING LIST
66
PAR
TS
LIST
FO
R G
RA
-ASC
-8A
L08C
L08D
L08A-X
L08B-X
L08C-X
W01
W02
W02T
W04
W04-1
Z01
Z02
Z03
94 1/4 in / 2394 mm
24 3/4 in / 614 mm
48 7/8 in /1242 mm
48 7/8 in / 1242 mm
57 5/16 in / 1456 mm
ROOF
FRONT & BACK
FRONT & BACK
ROOF LINE
BACK WALL
M4*30Screws for Doors
M3.5*16Screws for Roof Vents
M3*25Screw for End Caps
S02
ML01/S04
S05
J601
J602A-E
J602B-E
L28
W11
W13
W16
HQC01
HQC02
Z04, S04/ML01
M6*25
M6*14
M6*10For W01 and W02
END CAPS
END CAPS
END CAP
22 in /558 mm
SCREW DRIVER
10 MM NUT DRIVER
10 MM WRENCH
ROOF VENT ARM
ROOF VENT LATCH
ROOF VENT HARDWARE
2
2
2
2
4
2
4
2
5
2
13
9
4
6
140
30
2
2
2
2
1
1
1
2
2
4 EACH
GRAPHIC PART NAME SIZE/LOCATION QUANTITYGRAPHIC PART NAME SIZE/LOCATION QUANTITY
(GRA-ASC-8A) GRANDIO ASCENT 8’X8’ ALUMINUM PACKING LIST
67
PAR
TS
LIST
FO
R G
RA
-ASC
-8A
622-HNDL
622-HNDLNUT/BOLT
620
L21
622
622-R
622-L
623A
623B
J04
J07
J08A
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
4
2
1
2
1
1
2
2
4
2
4
DOOR HANDLES
DOOR HARDWARE
21 7/16 in / 545 mm
95 1/2 in / 2425 mm
67 7/8 in / 1724 mm
67 7/8 in / 1724 mm
67 7/8 in / 1724 mm
21 7/16 in / 545 mm
21 5/16 in / 542 mm
DOOR BOTTOM ROLLER
L21A END CAP
DOORS
(GRA-ASC-8A) GRANDIO ASCENT 8’X8’ ALUMINUM PACKING LIST
68
PAR
TS
LIST
FO
R G
RA
-ASC
-8A
AZ-1 / W17 S02/ML01
ML02
76 3/4 in / 1950 mmEXTENSION SUPPORT
NON FLANGED NUT
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
8
69
PAR
TS
LIST
FO
R G
RA
-ASC
-8P
Y1
Y2-1
Y2-2
Y3-1
Y3-2
Y4-1
Y4-2
Y5
Y6
Y7
Y8
Y9
LOWER BACK WALL PANEL
FRONT UPPER SIDEWALL
FRONT UPPER SIDEWALL
FRONT UPPER PEAK
FRONT UPPER PEAK
BACK MIDWALL
BACK MIDWALL
DOOR PANEL
SIDE PANEL
ROOF PANEL
ROOF VENT PANEL
UNDER ROOF VENT
GRAPHIC PART # SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
6
2
2
1
1
1
1
4
8
6
2
2
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
44 in / 1118 mm
8 1/4in / 209 mm
25 5/16 in / 643 mm
11/16 in /18 mm
17 3/4in / 451 mm
25 3/41 in / 654 mm
42 13/16 in /1088 mm
33 in / 839 mm
53 in / 1346 mm
58 1/8 in /1477 mm
19 1/8 in / 486 mm
36 7/8 in / 937 mm
25 5/16 in / 643 mm
8 1/4 in / 209 mm
17 3/4 in / 451 mm
11/16 in /18 mm
42 13/16 in /1088 mm
25 3/41 in / 654 mm
(GRA-ASC-8P) GRANDIO ASCENT 8’X8’ PANEL PACKING LIST
(GRA-ASC-4XA) GRANDIO ASCENT 4’ EXTENSION ALUMINUM PACKING LIST
602A
602B
603B
L08M-X
L08C
BZ-1
CZ-1
607-4X
607-XS
S08
S06
DP01
52 1/2 in / 1334 mm
57 1/8 in / 1451 mm
21 7/8 in / 555 mm
57 5/16 in / 1456 mm
46 3/4 in / 1187 mm
23 5/8 in / 600 mmROOF SUPPORT
19 11/16 in / 500 mmEAVE SUPPORT
47 1/2 in / 1187 mm
ROOF EXTENSION
M6*20Attaches the 607-XS to 607
M4*6Attaches DP01 to 607
ROOF CAP
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
4
1
2
2
2
2
1
1
5
3
1
606-WS
609-WS
609-4X-R609-4X-L
609-XS
S09
610-4X-R610-4X-L
DP02
DP02B
S07
615
616
618
21 3/4 in / 553 mmWINDOW SEAL
21 5/8 in / 550 mmWINDOW SEAL
46 3/4 in / 1187 mm
609 EXTENSION CONNECTORS
M4*6ATTACHES 609-XS TO 609’s
46 3/4 in / 1187 mm
GUTTER BRACKET CONNECTOR
GUTTER BRACKET CONNECTOR
M5*8ATTACHES DP02 TO DP02B
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 3/4 in / 500 mm
BLACK WINDOW SEAL
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
11
2
4
20
2
2
2
5
1
1
2
70
PAR
TS
LIST
FO
R G
RA
-ASC
-4X
S04/ML01
W04
W14
Z02
HQCO1
HQC02
Z04, S04/ML01
M6*14
ROOF VENT
L08M-X BRACKET
M3.5*16SCREWS FOR ROOF VENTS
ROOF VENT ARM
ROOF VENT LATCH
HQC01 HARDWARE
40
2
2
5
1
1
2/2
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
(GRA-ASC-4X) GRANDIO ASCENT 4’ EXTENSION ALUMINUM PACKING LIST
71
PAR
TS
LIST
FO
R G
RA
-ASC
-4X
72
PAR
TS
LIST
FO
R G
RA
-ASC
-4X
Y6
Y7
Y8
Y9
SIDE PANEL
ROOF PANEL
ROOF VENT PANEL
UNDER ROOF VENT PANEL
GRAPHIC PART # SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
4
3
1
1
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
53 in / 1346 mm
58 1/8 in /1477 mm
19 1/8 in / 486 mm
36 7/8 in / 937 mm
(GRA-ASC-4X) GRANDIO ASCENT 4’ EXTENSION PANEL PACKING LIST
602A
602B
603B
L08M-X
L08C
AZ-1 / W17S02/ML01
BZ-1
CZ-1
607-8X
607-XS
S08
S06
DP01
52 1/2 in / 1334 mm
57 1/8 in / 1451 mm
21 7/8 in / 555 mm
57 5/16 in / 1456 mm
93 1/4in / 2394 mm
76 3/4 in / 1950 mmEXTENSION SUPPORT
23 5/8 in / 600 mmROOF SUPPORT
19 11/16 in / 500 mmEAVE SUPPORT
93 7/16 in / 2374 mm
ROOF EXTENSION
M6*20ATTACHES 607-XS TO 607
M4*6ATTACHES DP01 TO 607
ROOF CAP
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
8
8
2
2
2
2
4
6
1
1
5
3
1
606-WS
609-WS
609-8X-R609-8X-L
609-XS
S09
610-8X-R610-8X-L
DP02
DP02B
S07
615
616
618
21 3/4 in / 553 mmWINDOW SEAL
21 5/8 in / 550 mmWINDOW SEAL
93 7/16 in / 2374 mm
609 EXTENSION
M4*6ATTACH THE 609-XS TO 609
93 7/16 in / 2374 mm
GUTTER BRACKET
GUTTER BRACKET
M5*8SCREW FOR GUTTER BRACKET
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 3/4 in / 500 mm
BLACK WINDOW SEAL
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
8
22
2
4
20
2
2
2
5
2
2
4
(GRA-ASC-8XA) GRANDIO ASCENT 8’ EXTENSION ALUMINUM PACKING LIST
73
PAR
TS
LIST
FO
R G
RA
-ASC
-8X
A
(GRA-ASC-8XA) GRANDIO ASCENT 8’ EXTENSION ALUMINUM PACKING LIST
S04/ML01
W04
W14
Z02
HQCO1
HQC02
Z04, S04/ML01
M6*14
ROOF VENT BRACKETS
L08M-X BRACKET
M3.5*16SCREWS FOR ROOF VENT
ROOF VENT ARM
ROOF VENT LATCH
HQC01 SCREW
65
4
2
9
2
2
4
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
74
PAR
TS
LIST
FO
R G
RA
-ASC
-8X
A
75
PAR
TS
LIST
FO
R G
RA
-ASC
-8X
P
Y6
Y7
Y8
Y9
SIDE PANEL
SIDE PANEL
ROOF VENT PANEL
UNDER ROOF VENT
GRAPHIC PART # SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
8
6
2
2
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
53 in / 1346 mm
58 1/8 in /1477 mm
19 1/8 in / 486 mm
36 7/8 in / 937 mm
(GRA-ASC-8XP) GRANDIO ASCENT 8’ EXTENSION PANEL PACKING LIST
76
PAR
TS
LIST
FO
R G
RA
-ASC
-BD
47 5/16 in / 1201 mm BACK CORNERS
17 in / 431 mm FRONT LEFT CORNER
68 7/8 in / 1750 mm FRONT RIGHT DOOR
68 7/8 in / 1750 mm FRONT LEFT DOOR
24 3/16 in / 614 mm
94 1/4 in / 2394 mm40 in / 1015 mm
M4*10M6*16
67 7/8 in / 1724 mm
67 7/8 in / 1724 mm
67 7/8 in / 1724 mm
21 7/16 in / 545 mm
21 7/16 in / 545 mm
21 5/16 in / 542 mm FRONT RIGHT
BOTTOM DOOR ROLLER
(GRA-ASC-BD) GRANDIO ASCENT BACKDOOR PACKING LIST
603A
603C
604R
604L
L08D
619 PACK619-BAR
S19S10 / ML02
622
622-R
622-L
620
623A
623B
J04
J08A
Z01
ML01/S04
ML01/S02
L21
J07
L28
W04
W02T
Y3-1
Y3-2
Y5
1/4 DB
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
1
1
2
1-6191-619 Bar
5 - S19 ScrewsS10 / ML02
2
1
1
2
2
2
4
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
13
30
4
1
2
2
1
2
1
1
4
1
DOOR
M4*30SCREWS FOR DOORS
M6*14
M6*25
95 1/2 in / 2425 mm
L21 ENDCAP
22 in / 558 mm FRONT RIGHT
CONNECTOR BRACKET
DOOR FRAME
UPPER ROOF PANEL
UPPER ROOF PANEL
DOOR PANELS
1/4 DRILL BIT
77
WA
RR
AN
TY
Grandio Greenhouse Limited Lifetime Warranty
1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warrantied for life. The word “defects” is de�ned as imperfections that impair the use of the product.
2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installa-tion, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the greenhouse or its components are not covered under this warranty.
4. This warranty does not cover scratching or scu�ng of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use will void this warranty.
5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this product. This warranty gives you speci�c legal rights, and you may also have other rights that vary from state to state.
52 1/2 in / 1334 mm
57 1/8 in / 1451 mm
21 7/8 in / 555 mm
57 5/16 in / 1456 mm
46 3/4 in / 1187 mm
23 5/8 in / 600 mmROOF SUPPORT
19 11/16 in / 500 mmEAVE SUPPORT
47 1/2 in / 1187 mm
ROOF EXTENSION
M6*20Attaches the 607-XS to 607
M4*6Attaches DP01 to 607
ROOF CAP
NOTES NOTES
G R E E N H O U S E S GRANDIO
®
GREENHOUSE USER MANUALKEEP IN A SAFE PLACE FOR REFERENCE
CONTACT US IF YOU NEED HELPOR
HAVE MISSING OR DAMAGED PARTS
GRANDIOGREENHOUSES.COM
BACKYARD LIVING SOURCE, INC.9543 W. EMERALD ST., SUITE 101
BOISE, ID 83704
1-866-448-8231
Grandio Ascent 8x12, 8x16, 8x20 & 8x24 Models