GR Config Z3 to RD3 ENG 002gram-group.com/.../2018/01/GR_Config_Z3_to_RD3_ENG_001.pdf · Step 1:...

QUICK CONFIGURATION GUIDE Connection Connect the “RS-232 to RD3 cable Z” (Ref. 36785) to the weight indicator and to the RD3 Repeater Indicator. Step 1: Configure the Z3 weight indicator for use with the RD3 Repeater Indicator The Z3 indicator is factory-configured for using a PR4 model printer. For connect it to RD3 Repeater Indicator, you need to first change this configuration before its use, following the indications contained in this document. Once this procedure has been completed, the configuration is registered in the unit’s non-volatile memory and it will not be necessary to repeat it. Press key [M/BG] to access the configuration options menu. 1. Press key à to move to the rS232 menu option. 2. Press key ¿ to validate. The visor will display the bAudr option. 3. Press key à repeatedly to move forward to the FOrN option and press key ¿ to access this submenu of options. 4. Press key à repeatedly to move forward to the rd3 option and press key ¿ to validate. 5. The visor will display the SAvE message, indicating that the selected option has been saved to the indicator’s non-volatile memory. 6. Press the ESC key repeatedly to exit the configuration options menu and return to normal operating mode (weight indicator). Gram Precision S.L. Travesía Industrial, 11 · 08907 Hospitalet de Llobregat · Barcelona (Spain) Tel. +34 902 208 000 · +34 93 300 33 32 Fax +34 93 300 66 98 [email protected] www.gram-group.com Download the full manual from the following link: http://gram-group.com/wp-content/uploads/2016/12/MANUAL_Z3_2016_ENG_001.pdf RS-232 to RD3 cable Z (Ref. 36785) EN

Upload
hoangxuyen
Category

Documents
view
217
download
2

Embed Size (px):

Transcript of GR Config Z3 to RD3 ENG 002gram-group.com/.../2018/01/GR_Config_Z3_to_RD3_ENG_001.pdf · Step 1:...

Page 1: GR Config Z3 to RD3 ENG 002gram-group.com/.../2018/01/GR_Config_Z3_to_RD3_ENG_001.pdf · Step 1: Configure the Z3 weight indicator for use with the RD3 Repeater Indicator The Z3 indicator

QUICK CONFIGURATION GUIDE

Connection

Connectthe“RS-232toRD3cableZ”(Ref.36785)totheweightindicatorandtotheRD3

RepeaterIndicator.

Step1:ConfiguretheZ3weightindicatorforusewiththeRD3RepeaterIndicator

TheZ3indicatorisfactory-configuredforusingaPR4modelprinter.ForconnectittoRD3RepeaterIndicator,youneedtofirstchangethisconfigurationbeforeitsuse,followingtheindicationscontainedinthisdocument.Oncethisprocedurehasbeencompleted,theconfigurationisregisteredintheunit’snon-volatilememoryanditwillnotbenecessarytorepeatit.

Presskey[M/BG]toaccesstheconfigurationoptionsmenu.

1. PresskeyàtomovetotherS232menuoption.

2. Presskey¿tovalidate.ThevisorwilldisplaythebAudroption. 3. PresskeyàrepeatedlytomoveforwardtotheFOrNoptionandpresskey¿toaccessthissubmenuofoptions.

4. Presskeyàrepeatedlytomoveforwardtotherd3optionandpresskey¿tovalidate.5. ThevisorwilldisplaytheSAvEmessage,indicatingthattheselectedoptionhasbeensavedtotheindicator’snon-volatile

memory.6. Press theESC key repeatedly to exit the configuration optionsmenu and return to normal operatingmode (weight

indicator).

Gram Precision S.L. Travesía Industrial, 11 · 08907 Hospitalet de Llobregat · Barcelona (Spain) Tel. +34 902 208 000 · +34 93 300 33 32 Fax +34 93 300 66 98 [email protected] www.gram-group.com

Downloadthefullmanualfromthefollowinglink:http://gram-group.com/wp-content/uploads/2016/12/MANUAL_Z3_2016_ENG_001.pdf

RS-232toRD3cableZ(Ref.36785)