Fusion Technology and ITER Mohamed Abdou Distinguished Professor, Mechanical and Aerospace...
-
Upload
melinda-austin -
Category
Documents
-
view
216 -
download
0
Transcript of Fusion Technology and ITER Mohamed Abdou Distinguished Professor, Mechanical and Aerospace...
Fusion Technology and ITER
Mohamed AbdouDistinguished Professor, Mechanical and Aerospace Engineering Department
Director, Center for Energy Science and Technology Advanced Research (CESTAR)Director, Fusion Science and Technology Center
University of California Los Angeles (UCLA)
Seminar at Shanghai Institute of Ceramics, Chinese Academy of Science
May 2006
Outline
• World energy needs• Fusion: Energy source for the XXI century• ITER• ITER Test Blanket• Principles of Fusion Nuclear Technology• Blanket concepts• He-Cooled Ceramic Breeder Blanket (HCBB)• Dual Coolant Lead-Lithium Concept (DCLL)• SiC/SiC Flow Channel Insert (FCI)• Liquid Walls• MHD Code Development• Summary
What is Nuclear Fusion?
• Nuclear Fusion is the energy-producing process taking place in the core of the Sun and stars
• The core temperature of the Sun is about 15 million °C. At these temperatures hydrogen nuclei fuse to give Helium and Energy. The energy sustains life on Earth via sunlight
Fusion Reactions• Deuterium – from water
(0.02% of all hydrogen is heavy hydrogen or deuterium)
• Tritium – from lithium(a light metal common in the Earth’s crust)
Deuterium + Lithium → Helium + Energy
This fusion cycle (which has the fastest reaction rate) is of interest for Energy Production
Figure 1.1 Energy use (in gigajoules) vs. GDP (on a purchasing power parity basis) for selected countries on a per capita basis. Data from the International Energy Agency. Upper line indicates ratio for the US; lower line indicates ratio for Japan and several Western European countries.
Figure 1.2. Human development index vs. per capita electricity use for selected countries. Taken from S. Benka, Physics Today (April 2002), pg 39, and adapted from A. Pasternak, Lawrence Livermore National Laboratory rep. no. UCRL-ID-140773.
The World, particularly in developing countries, needs a New Energy Source
• Growth in world population and growth in energy demand from increased industrialisation/affluence will lead to an Energy Gap which will be increasingly difficult to fill with fossil fuels
• Without improvements in efficiency we will need 80% more energy by 2020• Even with efficiency improvements at the limit of technology we would still
need 40% more energy
World Energy Scene* (I)World Energy Scene* (I)1) The world uses a lot of energy
Average power consumption = 13.6 TWs, or 2.2 kWs per person
World energy market ~ $3 trillion/yr (electricity ~$1 trillion/yr)
- very unevenly (OECD 6.2 kW/person; Bangladesh 0.20 kW/person; China 1.3kW/person)
2) World energy use is expected to grow
- growth necessary to lift billions of people out of poverty
3) 80% is generated by burning fossil fuels
climate change & debilitating pollution
- which won’t last for ever
*See Sir Chris Llewellyn-Smith, FPA, October 11, 2005
Need major new (clean) energy sources
- requires new technology
Future Energy UseFuture Energy Use
The International Energy Agency (IEA) expects the world’s energy use to increase 60% by 2030 (while population expected to grow from 6.2B to 8.1B) - driven largely by growth of energy use and population in India (current use = 0.7 kWs/person, vs. OECD average of 6.2 kWs/person) and China (current use = 1.3 kWs/person)
Strong link between energy use and the Human Development Index (HDI ~ life expectancy at birth + adult literacy and school enrolment + gross national product per capita at purchasing power parity) – need increased energy use to lift billions out of poverty
Carbon dioxide levels over the last 60,000 years - we are provoking the atmosphere!
Source University of Berne and National Oceanic, and Atmospheric Administration
Meeting the Energy Challenge Requires:Meeting the Energy Challenge Requires:Fiscal measures to change the behaviour of consumers,
and provide incentives to expand use of low carbon technologies
Actions to improve efficiency (domestic, transport, …)
Use of renewables where appropriate (although locally useful, not hugely significant globally)
BUT only four sources capable in principle of meeting a large fraction of the world’s energy needs:
• Burning fossil fuels (currently 80%) - develop & deploy CO2 capture and storage
• Solar - seek breakthroughs in production and storage• Nuclear fission - hard to avoid if we are serious about reducing fossil
fuel burning (at least until fusion available)• Fusion - with so few options, we must develop fusion as fast as
possible, even if success is not 100% certain
ITER
• The World is about to construct the next step in fusion development, a device called ITER
• ITER will demonstrate the scientific and technological feasibility of fusion energy for peaceful purposes
• ITER will produce 500 MW of fusion power
• Cost, including R&D, is 15 billion dollars
ITER Design - Main Features
Divertor
Central Solenoid
Outer Intercoil Structure
Toroidal Field Coil
Poloidal Field Coil
Machine Gravity Supports
Blanket Module
Vacuum Vessel
Cryostat
Port Plug (IC Heating)
Torus Cryopump
ITER Location
Caradache (France) Rokkasho (Japan)
Cadarache was selected as the ITER construction site. There will be some facilities in Rokassho under the “Broader Approach” agreement.
Fusion Nuclear Technology (FNT)
FNT Components from the edge of the Plasma to TF Coils (Reactor “Core”)
1. Blanket Components
2. Plasma Interactive and High Heat Flux Components
3. Vacuum Vessel & Shield Components
4. Tritium Processing Systems
5. Instrumentation and Control Systems
6. Remote Maintenance Components
7. Heat Transport and Power Conversion Systems
a. Divertor, limiter
b. RF antennas, launchers, wave guides, etc.
Other Components affected by the Nuclear Environment
Fusion Power & Fuel Cycle Technology
Plasma
Radiation
Neutrons
Coolant for energy conversion
First Wall
Shield
Blanket Vacuum vessel
Magnets
Tritium breeding zone
Blanket (including first wall)Blanket Functions:
A. Power Extraction– Convert kinetic energy of neutrons and secondary gamma rays into heat
– Absorb plasma radiation on the first wall
– Extract the heat (at high temperature, for energy conversion)
B. Tritium Breeding– Tritium breeding, extraction, and control
– Must have lithium in some form for tritium breeding
C. Physical Boundary for the Plasma– Physical boundary surrounding the plasma, inside the vacuum vessel
– Provide access for plasma heating, fueling
– Must be compatible with plasma operation
– Innovative blanket concepts can improve plasma stability and confinement
D. Radiation Shielding of the Vacuum Vessel
Blanket Materials1. Tritium Breeding Material (Lithium in some form)
Liquid: Li, LiPb (83Pb 17Li), lithium-containing molten salts
Solid: Li2O, Li4SiO4, Li2TiO3, Li2ZrO3
2. Neutron Multiplier (for most blanket concepts)
Beryllium (Be, Be12Ti)
Lead (in LiPb)
3. Coolant
– Li, LiPb – Molten Salt – Helium – Water
4. Structural Material– Ferritic Steel (accepted worldwide as the reference for DEMO)
– Long-term: Vanadium alloy (compatible only with Li), and SiC/SiC
5. MHD insulators (for concepts with self-cooled liquid metals)
6. Thermal insulators (only in some concepts with dual coolants)
7. Tritium Permeation Barriers (in some concepts)
8. Neutron Attenuators and Reflectors
Heat and Radiation Loads on First Wall
• Neutron Wall Load ≡ Pnw
Pnw = Fusion Neutron Power Incident on the First Wall per unit area
= JwEo
Jw = fusion neutron (uncollided) current on the first wall
Eo = Energy per fusion neutron = 14.06 MeV
• Typical Neutron Wall Load ≡ 1-5 MW/m2
At 1 MW/m2: Jw = 4.43 x 1017 n · m-2 · s-1
• Note the neutron flux at the first wall (0-14 MeV) is about an order of magnitude higher than Jw
• Surface heat flux at the first wallThis is the plasma radiation load. It is a fraction of the α-power
qw = 0.25 Pnw · fα
where f is the fraction of the α-power reaching the first wall
(note that the balance, 1 – f, goes to the divertor)
Tritium Breeding Blankets: Complex component submitted to very severe working conditions,
Needed in DEMO, not present in ITER
► ITER is a unique opportunity to test breeding blanket mock-ups: Test Blanket Modules (TBMs)
► It is an ITER mission : “ITER should test tritium breeding module concepts that would lead in a future reactor to tritium self-sufficiency, the extraction of high grade heat and electricity production.” (ITER SWG Report to the IC)
TBMs have to be representative of a DEMO breeding blanket, capable of ensuring tritium-breeding self-sufficiency using high-grade coolants for electricity production
► The ITER TBM Program is therefore a central element in the plans of all seven ITER Parties for the development of tritium breeding and power extraction technology.
What is the ITER TBM Program?
Integrated testing of breeding blanket and first wall components and materials in a Fusion Environment
• Breeding Blankets/FWs will be tested in ITER, starting on Day One, by inserting Test Blanket Modules (TBMs) in specially designed ports.
• Each TBM will have its own dedicated systems for tritium recovery and processing, heat extraction, etc. Each TBM will also need new diagnostics for the nuclear-electromagnetic environment.
• Each ITER Party is allocated limited space for testing two TBMs. (Number of Ports reduced to 3. Number of Parties increased to 7).
• ITER’s construction plan includes specifications for TBMs because of impacts on space (port, port area, hot cell, TCWS), shielding, vacuum vessel, remote maintenance, ancillary equipment, safety, availability, etc.
• The ITER Test Program is managed by the ITER Test Blanket Working Group (TBWG) with participants from the ITER International Team and representatives of the Parties. (However, this entity may change under the new international agreement being negotiated.)
Available TBM development time is limited: ITER Schedule calls for TBM testing from Day 1 of H-H plasma Operation
•“Day 1” H-H Phase TBM Testing in ITER is required for:– optimization of ITER plasma control, which can only be done with the TBMs
installed because the use of ferromagnetic structure and effects on plasma-wall interactions.
– licensing for ITER D-T operation, which requires TBM integrity under the severe ITER abnormal loading conditions (e.g. disruption) to be demonstrated in the H-H phase.
• Schedule from ITER documents show TBM starting from day 1
• It is not certain
how open ITER will be to fielding unproven TBMs in the D-T phases
TBMs Arrangement in ITER and Interfaces► 3 ITER equatorial ports (opening of 1.75 x 2.2 m2) devoted to TBM testing► TBMs installed within a water-cooled steel frame (thk. 20 cm), typically half-port size
vertical horizontal
TBM PORTS
The TBMs first wall is recessed 50 mm and protected with a Be layer
Shield plug
Frame
SampleTBM (RF)
TBM
TBMs tests need a whole TBM system
US ITER Test Blanket Module Concepts
The Dual-Coolant Lead-Lithium (DCLL) and the Helium Cooled Ceramic Breeder (HCCB) concepts have been selected for ITER testing by the US community.
The DCLL is chosen as an innovative concept that provides a “pathway” to higher outlet temperature and higher efficiency while using current generation low-activation ferritic steel (FS) as a structural material and SiC composite only as a non-structural insulator.
The HCCB is chosen as the most likely candidate for near term tritium breeding blankets, e.g. in an extended performance phase of ITER, while providing high grade heat for electricity production.
Both concepts use reduced activation ferritic steel (RAFS) as a structural material and high pressure helium as a coolant. RAFS maximum operating temperature (550C) dictates the maximum helium coolant outlet temperature.
DCLL Perspective cutaway
Self-cooled Pb-17Li
Breeding Zone
He-cooled steel
structure
SiC FCI
DCLL Typical Unit Cell
Assembly of 3 HCCB sub-modules in 1 half-port
Beryllium Pebble Bed
Solid Breeder Pebble Bed
Coolant Channel
US TBM Program has estimated its costs based on the degree of international collaboration / cost sharing
The high cost range scenario is for an independent US DCLL TBM and an independent HCCB TBM (similar to EU, Japan, and other parties independently testing two full modules.
The baseline scenario consists of (1) an independent US DCLL TBM , and (2) a supporting partnership with another party (Japan or EU) on the HCCB TBM providing only a submodules (size is 1/3 of a module)
The low cost range scenario is defined as a leading international partnership (with one or more ITER Parties) on DCLL TBM and a supporting partnership on the HCCB.
All costs over the next 10 years up to shipping of first TBM systems
Low - Partnership on both concepts
Baseline -Partnership on one
concept
High - Little Collaboration
ITER-TBM Estimated Cost (2006 k$) $60,392 $89,676 $119,666
Est. Escalation and Contingency $16,927 $23,271 $30,947
Total Program Cost (escalated k$ including contingency) $77,319 $112,947 $150,613
Comparison of Total Program Cost Ranges for the US TBM Program
(including escalation and contingency)
$0
$5,000
$10,000
$15,000
$20,000
$25,000
$30,000
To
tal
Co
sts
(k
$)
Low
Baseline
High
Low $1,882 $6,842 $10,423 $13,760 $14,377 $12,121 $8,775 $5,597 $2,759 $783
Baseline $2,749 $9,995 $15,226 $20,100 $21,002 $17,707 $12,819 $8,177 $4,030 $1,144
High $3,666 $13,328 $20,303 $26,803 $28,006 $23,611 $17,093 $10,903 $5,374 $1,525
FY06 FY07 FY08 FY09 FY10 FY11 FY12 FY13 FY14 FY15
Tritium Breeding
Natural lithium contains 7.42% 6Li and 92.58% 7Li.
The 7Li(n;n’)t reaction is a threshold reaction and requires an incident neutron energy in excess of 2.8 MeV.0.01
0.1
1
10
100
1000
1 10 100 1000 104 105 106 107
Li-6(n,alpha)t and Li-7(n,n,alpha)t Cross-Section
Li-6(n,a) tLi-7(n,na)t
Neutron Energy (eV)
MeVntnLi
MeVtnLi
47.2
78.47
6
6Li (n,) t
7Li (n;n’) t
Tritium Self-Sufficiency
• TBR ≡ Tritium Breeding Ratio = = Rate of tritium production (primarily in the blanket)
= Rate of tritium consumption (burnt in plasma)
Tritium self-sufficiency condition: Λa > Λr
Λr = Required tritium breeding ratio
Λr is 1 + G, where G is the margin required to: a) compensate for losses and radioactive decay between production and use, b) supply inventory for start-up of other fusion systems, and c) provide a hold-up inventory, which accounts for the time delay between production and use as well as reserve storage. Λr is dependent on many system parameters and features such as plasma edge recycling, tritium fractional burnup in the plasma, tritium inventories, doubling time, efficiency/capacity/reliability of the tritium processing system, etc.
Λa = Achievable breeding ratioΛa is a function of FW thickness, amount of structure in the blanket, presence of stabilizing shell materials, PFC coating/tile/materials, material and geometry for divertor, plasma heating, fueling and penetration.
NN /NN
Neutron Multipliers
0.001
0.01
0.1
1
10
106 107
Be-9 (n,2n) and Pb(n,2n) Cross-Sections- JENDL-3.2 Data
Be-9 (n,2n) Pb (n,2n)
Neutron Energy (eV)
• Almost all concepts need a neutron multiplier to achieve adequate tritium breeding.(Possible exceptions: concepts with Li and Li2O)
• Desired characteristics:– Large (n, 2n) cross-section with
low threshold– Small absorption cross-sections
• Candidates:– Beryllium is the best (large n, 2n
with low threshold, low absorption)
– Be12Ti may have the advantage of less tritium retention
– Pb is less effective except in LiPb
– Beryllium results in large energy multiplication, but resources are limited.
9Be (n,2n)
Pb (n,2n)
Examples of Neutron MultipliersBeryllium, Lead
Plasma
Plasma Facing
Component
PFCCoolant
Blanket Coolant
processing
Breeder Blanket
Plasma exhaust processing
FW coolant processing
Blanket tritium recovery system
Impurity separation
Impurity processing
Coolant tritium
recovery system
Tritium waste
treatment (TWT)
Water stream and air
processing
Fueling Fuel management
Isotopeseparation
system
Fuel inline storage
Tritium shipment/permanent
storage
waste
Solid waste
Only for solid breeder or liquid breeder design using separate coolant
Only for liquid breeder as coolant design
The D-T fuel cycle includes many components whose operation parameters and their uncertainties impact the required TBR
Examples of key parameters:
•ß: Tritium fraction burn-up
•Ti: mean T residence time in each component
•Tritium inventory in each component
•Doubling time
•Days of tritium reserves
•Extraction inefficiency in plasma exhaust processing
Fuel Cycle Dynamics
Blanket Concepts(many concepts proposed worldwide)
A. Solid Breeder Concepts– Always separately cooled
– Solid Breeder: Lithium Ceramic (Li2O, Li4SiO4, Li2TiO3, Li2ZrO3)
– Coolant: Helium or Water
B. Liquid Breeder ConceptsLiquid breeder can be:
a) Liquid metal (high conductivity, low Pr): Li, or 83Pb 17Li
b) Molten salt (low conductivity, high Pr): Flibe (LiF)n · (BeF2), Flinabe (LiF-BeF2-NaF)
B.1. Self-Cooled
– Liquid breeder is circulated at high enough speed to also serve as coolant
B.2. Separately Cooled
– A separate coolant is used (e.g., helium)
– The breeder is circulated only at low speed for tritium extraction
B.3. Dual Coolant
– FW and structure are cooled with separate coolant (He)
– Breeding zone is self-cooled
A Helium-Cooled Li-Ceramic Breeder Concept: Example
Material Functions•Beryllium (pebble bed) for neutron multiplication
•Ceramic breeder (Li4SiO4, Li2TiO3, Li2O, etc.) for tritium breeding
•Helium purge (low pressure) to remove tritium through the “interconnected porosity” in ceramic breeder
•High pressure Helium cooling in structure (ferritic steel)Several configurations exist (e.g. wall parallel or “head on” breeder/Be arrangements)
Stiffening plate provides the mechanical strength to the structural box
Radial-toroidal plate
Radial-poloidal plate
Grooves for helium coolant
Helium
Cut view
Mechanisms of tritium transport (for solid breeders)
Mechanisms of tritium transport
1) Intragranular diffusion
2) Grain boundary diffusion
3) Surface Adsorption/desorption
4) Pore diffusion
5) Purge flow convection
(solid/gas interface where adsorption/desorption occurs)
Li(n, 4He)T
Purge gas composition:
He + 0.1% H2
Tritium release composition:
T2, HT, T2O, HTO
Breeder pebble
“Temperature Window” for Solid Breeders
• The operating temperature of the solid breeder is limited to an acceptable “temperature window”: Tmin– Tmax
– Tmin, lower temperature limit, is based on acceptable tritium transport characteristics (typically bulk diffusion). Tritium diffusion is slow at lower temperatures and leads to unacceptable tritium inventory retained in the solid breeder
– Tmax, maximum temperature limit, to avoid sintering (thermal and radiation-induced sintering) which could inhibit tritium release; also to avoid mass transfer (e.g., LiOT vaporization)
• The limitations on allowable temperature window, combined with the low thermal conductivity, place limits on allowable power density and achievable TBR
Solid Breeder Concepts: Key Advantages and Disadvantages
Advantages
• Non-mobile breeder permits, in principle, selection of a coolant that avoids problems related to safety, corrosion, MHD
Disadvantages
• Low thermal conductivity, k, of solid breeder ceramics– Intrinsically low even at 100% of theoretical density (~ 1-3 W · m-1 · c-1 for ternary
ceramics)
– k is lower at the 20-40% porosity required for effective tritium release
– Further reduction in k under irradiation
• Low k, combined with the allowable operating “temperature window” for solid breeders, results in:– Limitations on power density, especially behind first wall and next to the neutron
multiplier (limits on wall load and surface heat flux)
– Limits on achievable tritium breeding ratio (beryllium must always be used; still TBR is limited) because of increase in structure-to-breeder ratio
• A number of key issues that are yet to be resolved (all liquid and solid breeder concepts have feasibility issues)
Liquid Breeders• Many liquid breeder concepts exist, all of which have
key feasibility issues. Selection can not prudently be made before additional R&D results become available.
• Type of Liquid Breeder: Two different classes of materials with markedly different issues.
a) Liquid Metal: Li, 83Pb 17Li
High conductivity, low Pr number
Dominant issues: MHD, chemical reactivity for Li, tritium permeation for LiPb
b) Molten Salt: Flibe (LiF)n · (BeF2), Flinabe (LiF-BeF2-NaF)
Low conductivity, high Pr number
Dominant Issues: Melting point, chemistry, tritium control
Liquid Breeder Blanket Concepts1. Self-Cooled
– Liquid breeder circulated at high speed to serve as coolant
– Concepts: Li/V, Flibe/advanced ferritic, flinabe/FS
2. Separately Cooled– A separate coolant, typically helium, is used. The breeder is
circulated at low speed for tritium extraction.
– Concepts: LiPb/He/FS, Li/He/FS
3. Dual Coolant– First Wall (highest heat flux region) and structure are cooled
with a separate coolant (helium). The idea is to keep the temperature of the structure (ferritic steel) below 550ºC, and the interface temperature below 480ºC.
– The liquid breeder is self-cooled; i.e., in the breeder region, the liquid serves as breeder and coolant. The temperature of the breeder can be kept higher than the structure temperature through design, leading to higher thermal efficiency.
Flows of electrically conducting coolants will experience complicated magnetohydrodynamic (MHD) effects
What is magnetohydrodynamics (MHD)?– Motion of a conductor in a magnetic field produces an EMF that can
induce current in the liquid. This must be added to Ohm’s law:
– Any induced current in the liquid results in an additional body force in the liquid that usually opposes the motion. This body force must be included in the Navier-Stokes equation of motion:
– For liquid metal coolant, this body force can have dramatic impact on the flow: e.g. enormous MHD drag, highly distorted velocity profiles, non-uniform flow distribution, modified or suppressed turbulent fluctuations
)( BVEj
BjgVVVV
11
)( 2pt
-1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Large MHD drag results in large MHD pressure drop
• Net JxB body force p = cVB2 where c = (tw w)/(a )
• For high magnetic field and high speed (self-cooled LM concepts in inboard region) the pressure drop is large
• The resulting stresses on the wall exceed the allowable stress for candidate structural materials
• Perfect insulators make the net MHD body force zero
• But insulator coating crack tolerance is very low (~10-7).
– It appears impossible to develop practical insulators under fusion environment conditions with large temperature, stress, and radiation gradients
• Self-healing coatings have been proposed but none has yet been found (research is on-going)
Lines of current enter the low resistance wall – leads to very high induced current and high pressure drop
All current must close in the liquid near the wall – net drag
from jxB force is zero
Conducting walls Insulated wall
-1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Li/Vanadium Blanket Concept
Breeding Zone
(Li flow)
Primary Shield
Secondary Shield
Reflector
Li
Li
Li
Secondary shield(B4C)
Primary shield
(Tenelon)
Reflector
Lithium
Lithium
Vanadium structure
Vanadium structure
Issues with the Lithium/Vanadium Concept
• Li/V was the U.S. choice for a long time, because of its perceived simplicity. But negative R&D results and lack of progress on serious feasibility issues have eliminated U.S. interest in this concept as a near-term option.
Conducting wall
Insulating layer
Electric currents lines
Leakage
current Crack
Issues
• Insulator– Insulator coating is required
– Crack tolerance (10-7) appears too low to be achievable in the fusion environment
– “Self-healing” coatings can solve the problem, but none has yet been found (research is ongoing)
• Corrosion at high temperature (coupled to coating development)
– Existing compatibility data are limited to maximum temperature of 550ºC and do not support the BCSS reported corrosion limit of 5m/year at 650ºC
• Tritium recovery and control• Vanadium alloy development is very costly and requires a very long time to
complete
Pathway Toward Higher Temperature Through Innovative Designs with Current Structural Material (Ferritic Steel):
Dual Coolant Lead-Lithium (DCLL) FW/Blanket Concept
First wall and ferritic steel structure cooled with helium
Breeding zone is self-cooled Structure and Breeding zone are
separated by SiCf/SiC composite flow channel inserts (FCIs) that Provide thermal insulation to
decouple PbLi bulk flow temperature from ferritic steel wall
Provide electrical insulation to reduce MHD pressure drop in the flowing breeding zone
Self-cooled Pb-17Li
Breeding Zone
He-cooled steel
structure
SiC FCI
DCLL Typical Unit Cell
Pb-17Li exit temperature can be significantly higher than the operating temperature of the steel structure High Efficiency
WHAT IS FCI ?• FCI (Flow Channel Insert) is the key
element of the DCLL blanket concept
• Both ITER and DEMO
• Made of 5-10 mm SiCf/SiC composite
• Pressure equalization openings (slot or holes) to nearly eliminate primary stress. Secondary (thermal) stress still exists
• The main functions are: - to reduce the MHD pressure drop
(electrical insulation); - to reduce heat leakage into He (thermal
insulation); - to separate hot PbLi (650C) from Fe
• No serious feasibility issues have been identified yet. However tailoring SiC properties and fabrication of complex shape FCIs is still an issue.
Pb-17Li exit temperature can be significantly higher than the operating temperature of the steel structure =>High Efficiency
SiCf/SiC FCI REQUIREMENTS SiC=1-100 S/m: 101-103
reduction of MHD pressure drop
• kSiC=1-10 W/m-K: heat leakage is <10% of the total power (DEMO)
• The optimal (SiC,kSiC)* is strongly dependent on the thermofluid MHD and should be determined by design tradeoffs, taking into account:
- P (<1-2 MPa) - heat leakage (<10-15% of the total power) - temperature gradient (<150-200 K per 5 mm FCI) - PbLi-Fe interface temperature (<470-500C)
• Suggested (DEMO): kSiC~2 W/m-K; SiC~100 S/m (S.Smolentsev, N.Morley, M.Abdou, MHD and Thermal Issues of the
SiCf/SiC FCI, FST, July 2006 )
* Only k and (across the FCI) are important
FCI RELATED R&D
Material science
• Development of low-conductivity grade 2-D woven SiCf/SiC with a thin surface sealing layer to avoid soaking of PbLi into pores (e.g. using CVD)
• Improvement of crack resistance • Reliable measurements of
SiCf/SiC properties at 300 to 800C, including effect of irradiation
• Fabrication of complex shape FCIs with pressure equalization openings and overlap sections
Thermofluid MHD
• Effectiveness of FCI as electrical and thermal insulator
• Pressure equalization (slot or holes ?)
• Effect of FCI on flow balancing in normal and abnormal (cracked FCI) conditions
• Optimal location of the FCIs in the module
THERMOFLUID MHD ANALYSIS
recommended
5 mm FCI (SiC~10) reduces the MHDpressure drop by factor of 100
Reduction of MHD pressure drop by FCI
Heat transfer is strongly affected by SiCvia flow modification
Radial temperature distribution in the poloidal duct (DEMO)
kSiC=2 W/m-K
MHD PHENOMENA in DCLL 1
• Effectiveness of FCI as electrical/thermal insulator
• MHD pressure drop and flow balancing
• Buoyancy effects and 2-D MHD turbulence, and their effect on thermal behavior of the module
US DEMO DCLL blanket module
Intensive studies, including modeling andexperiment, are being conducted at UCLA
MHD PHENOMENA in DCLL 2
• The flow in a poloidal duct is strongly affected by cross-sectional currents
• Interaction of the currents with a toroidal field results in a jet-type flow
Velocity profile and cross-sectional currents
High velocity jets
Flow in the gap
MHD PHENOMENA in DCLL 3
• Strong influence of buoyancy effect and 2-D MHD turbulence on heat transfer
• Reduction of high velocity jets due to turbulent diffusion
• About 10-time increase in effective thermal conductivity
• Circulation motionLaminar Turbulent
Reduction of high velocity jetsin a turbulent flow
Circulation motion
Many liquid wall reactor concepts for high power density were conceived & analyzed in APEX
Thin liquid wall concept (blanket region behind LW not shown)
Many candidate liquids were studied: Li, Sn-Li, Sn, Flibe and Flinabe
Several liquid wall flow schemes were conceived: – Thick liquid walls– Thin fast flowing protection layer (CLIFF)– Inertial or EM assisted wall adhesion– Integrated or stand-alone divertors
Concept performance was analyzed from many perspectives– Liquid wall flow MHD and heat transfer– Breeding, shielding and activation potential– Simplicity of system design, maintenance
Interactions of liquid walls with plasma operation were emphasized– Plasma edge effects, impurities & recycling– Liquid metal motion coupling to plasma modes
SurfaceRenewal
DivertorCassette
Fast FlowCassette
OutboardFast Flow
InboardFastFlow
Bottom DrainFlow
Summary
• The D-T Fusion process offers the promise of:– Virtually unlimited energy source from cheap abundant fuels;– No atmospheric pollution of greenhouse and acid rain gases;– Low radioactive burden from waste for future generations.
• Tremendous Progress has been achieved over the past decades in plasma physics and fusion technology.
• Fusion R&D involves many challenging areas of physics and technologies and is carried out through extensive international collaboration
• EU, JA, USA, RF, PRC, Korea, and India are about to construct ITER to demonstrate the scientific and technological feasibility of fusion energy (ITER will produce 500MW of fusion power )