Paul PlavicheanuProduct Manager – Electric

AutomationRegion Americas

IO-Link : standard communication (IEC 61131-9) for sensors and actuators

http://www.io-link.com/share/Downloads/At-a-glance/IO-Link_System_Description_engl_2013.pdf

• IO-Link is a serial, bidirectional point-to-point connection for signal transmission and energy supply under any networks, fieldbuses, or backplane buses. IO-Link is not a field bus.

• Powerful point-to-point communication based on established 3/5 wire sensor and actuator/drive connection without additional requirements regarding the cable material.

IO Link enables data communication from the field device to ERP system

Festo IO–Link advantages:• Cost effective, field device connection:• Pre-engineered mechatronics systems – OMS (Optimized Motion Series)• Scalable system: flexibility on device management• 3-5 wire cable, unshielded, M12 connector for fast and reliable connection

point• Bidirectional data transmission• IoT (Internet of Things), Industry 4.0 ready• ADP (Automatic Device Configuration): parameter storage in upper controller• Field device replacement with no commissioning: “plug and play”.• Data reporting (remote diagnose, alarms, trips) allows for easy

troubleshooting• Standardized field device connection technology• Adopted by all major Automation suppliers• Master IO Link Compatible with all major Bus communication

Important IO-Link Basics: NOT a fieldbus Requires an IO-Link

Master M12 ports typical Uses standard cables

I-Port

I-Port

Industrial Ethernet

- “the smart automation solution for the last meter of installation”

Festo IO-Link system configuration

Master Level

Device Level

Controlled Device Level

IO Link application advantage example on Rockwell environment:

• 25 conductors

• no diagnostics

• 5 conductors

• diagnostics

Customers who only specify Rockwell I/O will typically use MP valve terminals:• High termination costs• High cable costs• No diagnostics

Same customers can use IO-Link valve terminals:• Low termination costs• Low cable costs• Diagnostics• Automatic

configuration

Rockwell Point I/O - 1734-4IOL IO-link Master

Festo IO-Link Master: CECC-LK Mechatronic Controller

Pick & Place Handling System (max. 8 drives / PtP Only)

VTUB CTSL

VTUG MPA-L

Modbus TCP

Festo IO-Link Products

CMMO

Stepper motor actuator

4 IO-Link ports

CECC-LK

CPX I-Port Master for IO-Link devices vs. CTEL-MasterSolution for simple RIO modules

CPX with I-Port MasterSolution for smart sensors & actuators

CPX with I-Port Master for IO-Link devices

Festo I-Port for valve terminals & input modulesStandard IO-Link devices (V1.0 & V1.1)

4 Ports 2 Ports

Festo Master for IO-Link devices – CPX-CTEL …-LK -

http://ademtp00.de.festo.net/SpimsPlus/DocumentDetails_ps.aspx?DOCID=10000565642&LNG=en-IV

• Amount of ports for IO-Link devices: 2 (X1 & X2)

• Port type B, US1/US2 isolated

• Only available with EtherNet/IP (CPX-FB36R12), PROFINET & Sercos

Compatible to Siemens function block IOL-CALL

• Product description: CPX-CTEL-2-M12-5POL-LK

• Part number: TN2900543

• No compliance with standards to IO-Link masters Therefore it is called I-Port-Master for IO-Link devices

IO-Link over CTEU to CTEL installation system

CTEU/CAPCFlexible installationof fieldbus and I/O

CTEUDirect integration of fieldbus

CPX/CTELIntegration into a completesystem with CPX and control

The Festo I-Port interface is supported by different network or automation systems as for example the CPX-CTEL installation system. The valve terminal is always the same.

IO-Link Mode

Festo IO-Link devices – valve terminals

CPV-10/14

VTUG-… + VAEM-…-PT

MPA-C

MPA-L

VTOC-… + Interlock

VTUG-… + Interlock

Festo IO-Link devices – Sensors

SPAUPressure Sensor

SPAEPressure Sensor

SDATCylinder Position Transducer

Festo IO-Link devices: Proportional Pressure Regulators and Vacuum Generator

VPPM is the first proportional valve with IO-Link connectiontechnology.

Vacuum Generator OVEM-..-LK

Integrating into Rockwell environment: Point I/O - 1734-4IOL IO-link Master

Integrating Festo IO-Link devices into Rockwell Automation network

Main Points:Premier Integration with

Encompass Referenced Products from Festo

• Similar integration as Rockwell IO-link

CMMO-LK + Actuator• Cost Effective• No similar offering from RA• FHPP• FHPP + FPC• IO-Link VAEM for IO-Link (Referenced)MPA-L for IO-Link (Referenced)

Integrating Festo IO Link devices into Siemens network:

Thank YouFesto.com/io-link