FBDL & FBIL Driving/Indicator Lights Installation Instructions
5
1. Fesler Billet is not responsible for customer applications that are outside the normal and intended use of our products, including specific model and year applications. 2. Fesler Billet designs all parts off original OEM applications. Due to the vast array of manufacturers for aftermarket parts, it is possible that you may have to make some minor adjustments to either our part or your sheet metal in order for the part to fit properly. QUESTIONS OR COMMENTS? Call us at 1-866-583-9787 INSTALLATION INSTRUCTIONS FBDL-69CAM / FBIL-69CAM Camaro Driving Lights
Transcript of FBDL & FBIL Driving/Indicator Lights Installation Instructions
1. Fesler Billet is not responsible for customer applications that
are outside the normal and intended use of our products,
including specific model and year applications.
2. Fesler Billet designs all parts off original OEM applications.
Due to the vast array of manufacturers for aftermarket parts,
it is possible that you may have to make some minor
adjustments to either our part or your sheet metal in order
for the part to fit properly.
QUESTIONS OR COMMENTS?
Call us at 1-866-583-9787
INSTALLATION INSTRUCTIONS
FBDL-69CAM / FBIL-69CAM
Camaro Driving Lights
INSTALLATION INSTRUCTIONS
Halogen/L.E.D. Driving Lights Copyright 2011 © by Fesler Productions, LLC. All rights reserved.
Installation Instructions:
1. Disconnect battery
2. Unplug the stock turn signal light. The right and left plugs
are located at the front of the inner fender just behind the
radiator support on both sides of the car. Removal of the
battery will give easy access to the right side plug. You
can cut the stock indicator light wires close to the light
housing for easy access.
3. Remove the front indicator lights by removing two ¼-20
nuts from each light on the back side.
4. Using the supplied template, mark and cut the driving light
bracket.
5. Install the new Fesler driving light using two bolts/washers
provided.
Halogens = ¼-20 X ½ bolts and ¼ lock washers.
LEDs = 10-24 nuts and #10 washers
6. See the correct wiring diagram for your lighting application.
5A for the halogen driving lights wiring diagrams.
5B for LED Indicator lights w/out control board.
5C for LED Indicator lights with control board.
DRIVING (HALOGEN) LIGHT WIRING DIAGRAM
1-866-583-9787www.feslerbillet.com
DRIVING (HALOGEN) LIGHT WIRING DIAGRAM
1-866-583-9787www.feslerbillet.com
5B 5B87
87A
8586
30
Lt. B
lue
Brow
n
Yellow
Blue Black
Red
TURNSIGNAL
PARKING LIGHTINPUT @ DIMMER
SWITCH
BLUE - ParkBLACK - GroundBROWN - Park LightLT BLUE - Turn signal
These wire will becoming from your car.
Non-OEM or aftermarketwiring may be colored
di�erently.
FESLER BILLET - L.E.D. Indicator Lights1-866-583-9787
87
87A
8586
30
Lt. B
lue
Brow
n
Yellow
Blue Black
Red
TURNSIGNAL
PARKING LIGHTINPUT @ DIMMER
SWITCH
BLUE - ParkBLACK - GroundBROWN - Park LightLT BLUE - Turn signal
These wire will becoming from your car.
Non-OEM or aftermarketwiring may be colored
di�erently.
FESLER BILLET - L.E.D. Indicator Lights1-866-583-9787
5C 5C
WIRING DIAGRAM1969 Camaro L.E.D. Driving Light
with control board
Black - GROUNDYellow - TURN SIGNAL
Blue - RUNNING LIGHTRed - DRIVING LIGHT
Grey - POSITIVE
1-866-553-1856www.feslerbuilt.com
WIRING DIAGRAM1969 Camaro L.E.D. Driving Light
with control board
Black - GROUNDYellow - TURN SIGNAL
Blue - RUNNING LIGHTRed - DRIVING LIGHT
Grey - POSITIVE
1-866-553-1856www.feslerbuilt.com
