1 pc required

800mm1. Signal cable (Throttle)

4. Silicone Battery cable (No. 12AWG or 14AWG)

800mm

1 pc required

2 pcs required

800mm3. Signal cable (Alieron)

F-86 SABREScale EDF Radio Control model airplane

Model No : FF-D005

UNDER SAFETY PRECAUTIONSThis radio control is not a toy!

- Always keep this instruction manual ready on hand for quick reference.- Assemble this kit only places out of children reach.- First-time builders of EDF model should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any parts of the construction.- Taking out liability insurance is recommended.- You are responsible for this model’s assembly and safe operation.

Wingspan : 1420mm

You need to purchase the following accessories separately to complete the assembly.

2 pcs required

800mm2. Signal cable (Elevator)

1 pc required

5. 60A Electric Speed Control (ESC) w/BEC

60Aw/ BEC

1 pc required

6. B36 Brushless Motor, 1600-1800kv, Shaft dia 5mm

5 pcs required

7. Micro servo, 8g, torque >1.0kg

1 pc required

8. Li-Po Battery, 5-cells (18.5v), 3600mAh, 20C

Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

A

B

A A

Sharp Hobby Knife

Needle Nose Pliers

Scissors

Awl

8mm Box Driver

Screw driver

Double-sided Tape

Solder Iron (80W above)

Epoxy Glue

A-A-size Batteries(Transmitter)

Solder

Tools Required

Battery required

Kit contents

1

2

3

5

4

6

7

8

9

10

11

12

13

15

14

16

17

18

19

20

21

22

23

24

25

26

27

4

10

4

3

2

16

2

1

1

3

4

2

1

1

2

1

2

2

2

4

2

1

3

Horn

3x4mm Screw

Linkage stopper

Landing gear

4.0mmbind nut

4x30mm screw

4x30mm screw

Exhaust pipe

3mm plywood

3mm collar

120x20x3mmplywood

130x15x3mmplywood

30x10x3mmplywood

3mm plywood

3mm plywood

3mm plywood

3mm plywood

3mm collar

1

1

1

Canopy lock

Nose x 1Main x 2

Foam Glue 1 Foam glue

1 x 30 mm wire

3 x 54mm wire

3 x 40mm wire

1x 65mm wire

1x 100mm wire

3 x 4mm screw

Canopy Fuel Tank

Fuselage

Wing

Vertical Tail Wing Horizontal Tail Wing

Ducted Fan UnitDecal

A A

Li-Po Batteries(Motor)

First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying a badly assembled or badly adjusted aircraft is very dangerous!

In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone!

This model aircraft is designed to be powered by an electric-motor. Installing a over power motor and engine, or flying thismodel aggressively may lead to serious damage and accidents!

Warning !

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

FLYFLY

HOBBY

Horizontal Tail

800mm

Optional servo extension cable required forthe connection of the elevator servos to receiver.

2 pcs required

Elevator

Throttle

To ESCBattery plug

To ESCThrottle

Battery

Elevator

Optional extension cable required forthe connection of the ESC.

1 pc required

800mm1. Single cable (Throttle)

2. Silicone Battery cable (No. 12AWG or 14AWG)

800mm

1 pc required

1

Fuselage2

65mm

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

FLYFLY

HOBBY

Fuselage3

A B

A B

Nose Gear4

Note : Diagram included the optional air retract system. Please refer to the retract system instruction for the installation.

Air Retractsystem

A B

Don’t mix up the parts of left and right. The letter marked on the plywood.

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

FLYFLY

HOBBY

Fuselage5

Assembly Fan unit6

Elevator

Throttle

Battery

Optional

Air valve (main gear)

Connect to main

retract gear air cylinder

(Optional)

Aileron

Connect to aileron servo

Optional extension cable required forthe connection of the aileron servo.

2 pcs required

800mm1. Single cable (Alieron)

Note : Install the cable and air tube before glue the fuselage together with epoxy.

A B

(a) Never operate the unit with loose items of clothing or equipment near to the intake area.(b) Never operate the unit held in your hands as personal injury, or damage to the unit may occur.(c) Always do a thorough inspection of the unit prior to any operational use.(d) Always think safety first.(e) Secure all the screws. If any screws loose while rotating and the serious injury may occur.Caution : As proper use of the fan unit is out of the influence of the manufacturer, the operation of the fan unit is on owners risk!This is not a toy! The unit should only be operated by childs of 12 years and supervised by an adult.

Fan & ESC7

Wing construction8

A B

A B

A B

A B

FLYFLY

HOBBY

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com

ESC

C

Wing construction9

10

1

2

2mm Nut

3 x 5 mm

Linkage Stopper

1 x100mm rod

A B

Fin construction

FLYFLY

HOBBY

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

A B A

B

A B

A B

A B

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.comC

FLYFLY

HOBBY

11

Adjustment12

A A’

B B’

A = A’B = B’

ELEVATOR

AILERON25 mm25 mm

25 mm25 mm

217 mm

Never fly before checking the CG’s required position.

Reposition the receiver and battery to obtain the correct CG’s location.

NEVER fly the model without well balancing.

184 mm

Adjustment

165mm150mm

217 mm