exz3_e_1

Thank you for purchasing this CASIO Product. Before using it, be sure to read the precautions contained in this Users Guide, and keep the Users Guide in a safe place for future reference.

E

Digital Camera

EX-Z3Users Guide

K855PCM1DMX

INTRODUCTION

2

INTRODUCTIONUnpacking

Check to make sure that all of the items shown below are included with your camera. If something is missing, contact yourdealer as soon as possible.

CameraRechargeable lithiumion battery (NP-20)

CD-ROM

USB Cradle(CA-21)

USB Cable Basic Reference

PHOTO CHARGE USB

Strap

Special AC Adaptor(Inlet Type) AC power cord *

* The shape of the ACpower cord plug variesaccording to country orgeographic area.

Note that the shape of the AC adaptor depends on the area where you purchased the camera.

Special AC Adaptor(Plug-in Type)

INTRODUCTION

3

Contents

2 INTRODUCTION

Unpacking .................................................................... 2Features ....................................................................... 9Precautions ................................................................. 11

General Precautions 11Data Error Precautions 12Operating conditions 13Condensation 13LED Backlight 14Lens 14Other 14

15 QUICK START GUIDE

First, charge the battery! ............................................ 15To configure display language and clock settings ..... 16To record an image .................................................... 17To view a recorded image .......................................... 17To delete an image ..................................................... 18

19 GETTING READY

About This Manual ..................................................... 19General Guide ............................................................ 20

Camera 20USB Cradle 21

Monitor Screen Contents ........................................... 22REC mode 22PLAY mode 23Changing the Contents of the Monitor Screen 24

Indicator Lamps .......................................................... 24Attaching the Strap .................................................... 25Power Requirements ................................................. 25

To load the battery 25To remove the battery 27To charge the battery 27Power Supply Precautions 32Turning the Camera On and Off 35Configuring Power Saving Settings 36

Using the On-screen Menus ...................................... 37Configuring Display Language and Clock Settings ... 39

To configure display language and clock settings 40

INTRODUCTION

4

43 BASIC IMAGE RECORDING

Recording an Image ................................................... 43Recording Precautions 45About Auto Focus 46About the REC Mode Monitor Screen 46

Using the Optical Viewfinder ...................................... 47Using Zoom ................................................................ 48

Optical Zoom 48Digital Zoom 49

Using the Flash .......................................................... 50Flash Unit Status 52Flash Precautions 52

Using the Self-timer ................................................... 53Specifying Image Size and Quality ............................ 55

To specify the image size 55To specify image quality 56

57 OTHER RECORDING FUNCTIONS

Selecting the Focus Mode ......................................... 57Using Auto Focus 57Using the Macro Mode 58Using the Infinity Mode 59Using Manual Focus 59Using Focus Lock 60

Exposure Compensation (EV Shift) ........................... 61Adjusting White Balance ............................................ 63

Adjusting White Balance Manually 64Using the Best Shot Mode ......................................... 65

Creating Your Own Best Shot Setup 66Combining Shots of Two People into a Single Image(Coupling Shot) .......................................................... 69Recording a Subject onto an Existing BackgroundImage (Pre-shot) ........................................................ 71Using the Movie Mode ............................................... 73Using the Histogram .................................................. 75REC Mode Camera Settings ..................................... 76

Specifying ISO Sensitivity 76Turning Image Review On and Off 77Assigning Functions to the [] and [] Keys 77Specifying Power On Default Settings 78Resetting the Camera 79

80 PLAYBACK

Basic Playback Operation .......................................... 80Flipping the Display .................................................... 81Zooming the Display Image ....................................... 82Resizing an Image ..................................................... 83

INTRODUCTION

5

Cropping an Image..................................................... 84Playing a Movie .......................................................... 85Displaying the 9-image View ..................................... 86

Selecting a Specific Image in the 9-image View 87Displaying the Calendar Screen ................................ 87Playing a Slide Show ................................................. 88

To specify the slideshow images 90To specify the slideshow time 91To set the slideshow interval 91Using the Photo Stand Feature 92

Rotating the Display Image ........................................ 93

94 DELETING FILES

Deleting a Single File ................................................. 94Deleting All Files ........................................................ 95

96 FILE MANAGEMENT

Folders ....................................................................... 96Memory Folders and Files 96

Protecting Files .......................................................... 97To protect a single file 97To protect all files in memory 98

DPOF .......................................................................... 98To configure print settings for a single image 99To configure print settings for all images 100

PRINT Image Matching II .......................................... 101Exif Print ................................................................... 101Using USB DIRECT-PRINT ..................................... 102Using the FAVORITE Folder .................................... 104

To copy a file to the FAVORITE folder 104To display a file in the FAVORITE folder 105To delete a file from the FAVORITE folder 106

108 OTHER SETTINGS

Specifying the File Name Serial NumberGeneration Method .................................................. 108Turning the Key Tone On and Off ............................ 109Specifying an Image for the Startup Screen ........... 109Using the Alarm .........................................................110

To set an alarm 110Stopping the Alarm 111

Setting the Clock .......................................................112To select your Home Time zone 112To set the current time and date 113Changing the Date Format 113

Using World Time ......................................................114To display the World Time screen 114To configure World Time settings 114To configure summer time (DST) settings 115

Changing the Display Language ..............................116Formatting Built-in Memory .......................................117

INTRODUCTION

6

118 USING A MEMORY CARD

Using a Memory Card ............................................... 119To insert a memory card into the camera 119To remove a memory card from the camera 119Formatting a Memory Card 120Memory Card Precautions 121

Copying Files ........................................................... 122To copy all the files in built-in memory

to a memory card 122To copy a file from a memory card to built-in memory 123

124 VIEWING IMAGES ON A COMPUTER

Using the Camera with a Windows Computer ........ 124USB Connection Precautions 129

Using the Camera with a Macintosh Computer ....... 129USB Connection Precautions 134

Operations You Can Perform from Your Computer .. 134Using a Memory Card to Transfer Imagesto a Computer .......................................................... 135Memory Data ............................................................ 136

DCF Protocol 136Memory Directory Structure 136Image Files Supported by the Camera 137Built-in Memory and Memory Card Precautions 138

139 USING THE CAMERA WITH A COMPUTER

Using the Album Feature ......................................... 139Creating an album 139Selecting an Album Layout 140Configuring Detailed Album Settings 141Viewing Album Files 143Saving an Album 146

Installing the Software from the CD-ROM ............... 146About the bundled CD-ROM 146Computer System Requirements 147

Installing Software from the CD-ROM in Windows ... 148Getting Started 148Selecting a Language 148Viewing the Contents of the Read me File 149Installing an Application 149Viewing User Documentation (PDF Files) 150User Registration 150Exiting the Menu Application 150

Installing Software from the CD-ROMon a Macintosh ......................................................... 151

Installing Software 151Viewing User Documentation (PDF Files) 152

INTRODUCTION

7

154 APPENDIX

Menu Reference ....................................................... 154Indicator Lamp Reference ....................................... 156

REC mode 157PLAY mode 158USB Cradle Indicator Lamps 158

Troubleshooting Guide ............................................. 159Display Messages 162

Specifications ........................................................... 163Main Specifications 163

INTRODUCTION

8

IMPORTANT! The contents of this manual are subject to change

without notice. CASIO COMPUTER CO., LTD. assumes no

responsibility for any damage or loss resulting fromthe use of this manual.

CASIO COMPUTER CO., LTD. assumes noresponsibility for any loss or claims by third partieswhich may arise through the use of the EX-Z3.

CASIO COMPUTER CO., LTD. shall not be heldliable for any damages or losses suffered by you orany third party due to the use of Photo Loader and/orPhotohands.

CASIO COMPUTER CO., LTD. assumes noresponsibility for any damage or loss caused bydeletion of data as a result of malfunction, repairs, orbattery replacement. Be sure to back up all importantdata on other media to protect against its loss.

The SD logo is a registered trademark. Windows, Internet Explorer, and DirectX are

registered trademarks of Microsoft Corporation. Macintosh is a registered trademark of Apple

Computer, Inc. MultiMediaCard is a trademark of Infineon

Technologies AG of Germany, and licensed to theMultiMediaCard Association (MMCA).

Acrobat and Acrobat Reader are trademarks ofAdobe Systems Incorporated.

The USB driver (mass storage) uses PhoenixTechnologies Ltd. software.Compatibility Software Copyright C 1997Phoenix Technologies Ltd., All Rights Reserved.

Other company, product and service names usedherein may also be trademarks or service marks ofothers.

Photo Loader and Photohands are the property ofCASIO COMPUTER CO., LTD. Except as stipulatedabove, all copyrights and other related rights to theseapplications revert to CASIO COMPUTER CO., LTD.

Copyright RestrictionsExcept for the purposes of your own personal enjoyment,unauthorized copying of snapshot files and movie filesviolates copyright laws and international contracts.Distribution to third parties of such files over the Internetwithout permission of the copyright holder, whether forprofit or for free, violates copyright laws and internationalcontracts.

INTRODUCTION

9

Features 3.2 million Effective Pixels

A high-resolution megapixel CCD provides 3.2 millioneffective pixels (3.34 million total pixels) for images thatprint beautifully.

2.0-inch TFT color LCD monitor screen

12X seamless zoom3X optical zoom, 4X digital zoom

10MB Flash memoryImages can be recorded without using a memory card.

Support for SD memory cards and MMC (MultiMediaCards) for memory expansion

Easy ChargingJust place the camera onto the USB cradle to charge itsbattery.

Easy Image TransferTransfer images to a computer simply by placing thecamera onto the USB cradle.

Photo Stand featureA slideshow of images in file memory can be played whilethe camera is on its USB cradle.

Best ShotSimply select the sample scene that matches the type ofimage you are trying to record and the camera performstroublesome setups automatically for beautiful picturesevery time.

Coupling Shot and Pre-shotCoupling Shot lets you combine two subjects into a singleimage, while Pre-shot lets you add a subject to apreviously recorded background image. This means youcan create images that include you and your friend, evenif you are the only two people around. You can useCoupling Shot and Pre-shot by selecting the applicablesample images in the Best Shot mode.

Triple Self-timer modeThe self-timer can be set up to repeat three times,automatically.

Real-time histogramAn on-screen histogram lets you adjust exposure as youview the effect on overall image brightness, which makesshooting under difficult lighting conditions easier thanever before.

World TimeA simple operation sets the current time for your currentlocation. You can select from among 162 cities in 32 timezones.

INTRODUCTION

10

AlarmA built-in alarm helps to keep you on time for importantevents, and even can be used in place of an alarm clock.You can also have a specific image appear on themonitor screen when the alarm time is reached.

Album FunctionHTML files are generated automatically to create analbum of recorded images. Album contents can be viewedand printed using a standard Web browser. Images canalso be incorporated into Web pages quickly and easily.

Calendar screenA simple operation displays a full-month calendar on thecameras monitor screen. Each day of the full-monthcalendar shows a thumbnail of the first image recordedfor that date, which helps to make searching for aparticular image quicker and easier.

Movie mode with audio

DCF Data StorageDCF (Design rule for Camera File system) data storageprotocol provides image inter-compatibility between thedigital camera and printers.

Digital Print Order Format (DPOF)Images can be printed easily in the sequence you wantusing a DPOF compatible printer. DPOF can also be usedwhen specifying images and quantities for printing byprofessional print services.

PRINT Image Matching II CompatibleImages include PRINT Image Matching II data (modesetting and other camera setup information). A printer thatsupports PRINT Image Matching II reads this data andadjusts the printed image accordingly, so your imagescome out just the way you intended when you recordedthem.

USB DIRECT-PRINT supportYour camera supports USB DIRECT-PRINT, which wasdeveloped by Seiko Epson Corporation. When connecteddirectly to a printer that supports USB DIRECT-PRINT,you can select images to print and start the printoperation directly from the camera.

Bundled with Photo Loader and PhotohandsYour camera comes bundled with Photo Loader, thepopular application that automatically loads images fromyour camera to your PC. It also comes with Photohands,and application that makes image retouching quick andeasy.

INTRODUCTION

11

Precautions

General PrecautionsBe sure to observe the following important precautionswhenever using the EX-Z3.All references in this manual to this camera and thecamera refer to the CASIO EX-Z3 Digital Camera. Never try to take pictures or use the built-in display while

operating a motor vehicle or while walking. Doing socreates the danger of serious accident.

Never try to open the case of the camera or attempt yourown repairs. High-voltage internal components create therisk of electric shock when exposed. Always leavemaintenance and repair work up to a CASIO authorizedservice center.

Never look at the sun or any other bright light through thecameras viewfinder. Doing so can damage your eyesight.

Keep the small parts and accessories of this camera outof the reach of small children. If swallowed accidentally,contact your physician immediately.

Never fire the flash in the direction of a person operatinga motor vehicle. Doing so can interfere with the driversvision and create the danger of accident.

Never fire the flash while it is too close to the subjectseyes. Intense light from the flash can cause eye damageif it is fired too close to the eyes. This is especially truewith young children. When using the flash, the camerashould be at least one meter (3.3) from the eyes of thesubject.

Keep the camera away from water and other liquids, andnever let it get wet. Moisture creates the danger of fireand electric shock. Never use the camera outdoors in therain or snow, at the seashore or beach, in the bathroom,etc.

Should foreign matter or water ever get into the camera,immediately turn it off. Next, remove the cameras batteryand/or unplug the AC adaptor power cord from the poweroutlet, and contact your dealer or nearest CASIOauthorized service center. Using the camera under theseconditions creates the danger of fire and electric shock.

Should you ever notice smoke or a strange odor comingout of the camera, immediately turn it off. Next, takingcare you do not burn your fingers, remove the camerasbattery and/or unplug the AC adaptor power cord from thepower outlet, and contact your dealer or nearest CASIOauthorized service center. Using the camera under theseconditions creates the danger of fire and electric shock.After making sure there is no more smoke coming fromthe camera, take it to your nearest CASIO authorizedservice center for repair. Never attempt your ownmaintenance.

INTRODUCTION

12

Never use the AC adaptor to power any other devicebesides this camera. Never use any other AC adaptorbesides the one that comes with this camera.

Never cover the AC adaptor with a quilt, blanket, or othercover while it is in use, and do not use it near a heater.

At least once a year, unplug the AC adaptor power cordfrom the power outlet and clean the area around theprongs of the plug. Dust build up around the prongs cancreate the danger of fire.

If the cameras case should ever become cracked due todropping it or otherwise subjecting it to rough treatment,immediately turn it off. Next, remove the cameras batteryand/or unplug the AC adaptor power cord from the poweroutlet, and contact your dealer or nearest CASIOauthorized service center.

Never use the camera inside of an aircraft or in any otherareas where its use is prohibited. Doing so can result inan accident.

Physical damage and malfunction of this camera cancause the data stored in its memory to be deleted. Besure to always keep backup copies of data by transferringthem to personal computer memory.

Never open the battery cover, disconnect the AC adaptorfrom the camera, or unplug the AC adaptor from the wallsocket while recording images. Doing so will not onlymake storage of the current image impossible, it can alsocorrupt other image data already stored in file memory.

Data Error Precautions Your digital camera is manufactured using precision

digital components. Any of the following creates the riskof corruption of data in file memory.

Removing the battery or memory card, or setting thecamera onto the USB cradle while the camera isperforming a record or memory access operation

Removing the battery, removing the memory card, orplacing the camera onto the USB cradle while theoperation lamp is still flashing after you turn off thecamera

Disconnecting the USB cable, removing the camerafrom the USB cradle, or disconnecting the AC adaptorfrom the USB cradle while a data communicationoperation is being performed

Low battery power Other abnormal operations

Any of the above conditions can cause an error message toappear on the monitor screen (page 162). Follow theinstructions provided by the message to eliminate thecause of the error.

INTRODUCTION

13

Operating conditions This camera is designed for use in temperatures ranging

from 0C to 40C (32F to 104F). Do not use or keep the camera in the following areas.

In areas subject to direct sunlight In areas subject to high humidity or dust Near air conditioners, heaters, or other areas subject

to temperature extremes Inside of a closed vehicle, especially one parked in the

sun In areas subject to strong vibration

Condensation When you bring the camera indoors on a cold day or

otherwise expose it to a sudden change of temperature,there is the possibility that condensation can form on theexterior or on interior components. Condensation cancause malfunction of the camera, so you should avoidexposing it to conditions that might cause condensation.

To keep condensation from forming, place the camerainto a plastic bag before moving it into a location that ismuch warmer or colder than your current location. Leaveit in the plastic bag until the air inside the bag has achance to reach the same temperature as the newlocation. If condensation does form, remove the batteryfrom the camera and leave the battery cover open for afew hours.

INTRODUCTION

14

LED Backlight The monitor screen is illuminated by an LED backlight. A

dark monitor screen indicates that the LED backlight hasreached the end of its service life, and needs to bereplaced by a CASIO authorized service center. Note thatyou will be charged for LED backlight replacement. TheLED backlight brightness is reduced by half after about1,000 hours of use.

Lens Never apply too much force when cleaning the surface of

the lens. Doing so can scratch the lens surface and causemalfunction.

Fingerprints, dust, or any other soiling of the lens caninterfere with proper image recording. Never touch thelens with your fingers. You can remove dust particlesfrom the lens surface by using a lens blower to blow themoff. Next, wipe the surface of the lens with a soft lenscloth.

Other The camera may become slightly warm during use. This

does not indicate malfunction. If the exterior of the camera needs cleaning, wipe it with a

soft, dry cloth.

QUICK START GUIDE

15

QUICK START GUIDEFirst, charge the battery!1. Load the battery (page 25). 2. Place the camera onto the USB cradle to charge the

battery (page 27). Note that the shape of the AC adaptor depends on the area where

you purchased the camera. It takes about two hours to achieve a full charge.

1

2

3

Stopper

PHOTO CHARGE USB

DISP

MENU

SET

RECPLAY

2

1 Inlet Type

1 Plug-in Type

QUICK START GUIDE

16

1. Press the power button to turn on the camera.2. Press [] to select the language you want.3. Press [SET] to register the language setting.4. Use [], [], [], and [] to select the geographical

area you want, and then press [SET].5. Use [] and [] to select the city you want, and then

press [SET].6. Use [] and [] to select the summer time (DST)

setting you want, and then press [SET].7. Use [] and [] to select the date format setting you

want, and then press [SET].8. Set the date and the time.9. Press [SET] to register the clock settings and exit the

setting screen.

DISP

MENU

SET

RECPLAY

1

2, 3, 4, 5, 6, 7, 8, 9

To configure display language and clock settings Be sure to configure the following settings

before using the camera to record images.(See page 39 for details.)

QUICK START GUIDE

17

1. Press the power button to turn on thecamera.

2. Align the mode selector with PLAY.3. Use [] and [] to scroll through the

images.

DISP

MENU

SET

RECPLAY

1

3

2

To view a recorded image(See page 80 for details.)

1. Press the power button to turn on the camera.2. Align the mode selector with REC.3. Point the camera at the subject, use the monitor

screen or viewfinder to compose the image, andthen press the shutter release button half way. When proper focus is achieved, the focus frame turns green

and the green operation lamp lights.

4. Holding the camera still, gently press the shutterrelease button.

To record an image(See page 43 for details.)

DISP

MENU

SET

RECPLAY

1

3

42

1200120016001600NORMALNORMAL

9999

0303/1212/24241212:5858

IN

1 / 10001 / 1000F2.6F2.6

Greenoperation lamp

Focus frame

QUICK START GUIDE

18

1. Press the power button to turn on the camera.2. Align the mode selector with PLAY.3. Press [] ( ).4. Use [] and [] to display the image you want to delete.5. Use [] and [] to select Delete.

To exit the image delete operation without deleting anything, selectCancel.

6. Press [SET] to delete the image.

To delete an image(See page 94 for details.)

DISP

MENU

SET

RECPLAY

3, 4, 5, 6

12

GETTING READY

19

GETTING READYThis section contains information about things you need toknow about and do before trying to use the camera.

About This ManualThis section contains information about the conventionsused in this manual.

TerminologyThe following table defines the terminology used in thismanual.

Button OperationsButton operations are indicated by the button name insideof brackets ([ ]).

On-screen TextOn-screen text is always enclosed by double quotationmarks ( ).

File MemoryThe term file memory in this manual is a general term thatrefers to the location where your camera is currently storingthe images you record. File memory can be any one of thefollowing three locations.

The cameras built-in Flash memory An SD memory card loaded in the camera A MultiMediaCard loaded in the camera

For more information about how the camera stores images,see page 118.

This term as used in thismanual:this camera or thecamera

file memory

battery

optional charger unit

Means this:

The CASIO EX-Z3 DigitalCameraThe location where thecamera is currently storingimages you record (page 43)The NP-20 RechargeableLithium Ion BatteryThe optionally availableCASIO BC-10L Charger Unit

GETTING READY

20

65

1 234

Front

General GuideThe following illustrations show the names of each component, button, and switch on the camera.

Camera

1 Shutter release button2 Power button3 Flash4 Self-timer lamp5 Microphone6 Lens

7 Viewfinder8 Operation lamp9 Mode selector0 [MENU] buttonA Zoom buttonB Strap ringC [SET] buttonD [][][][]E [DISP] buttonF Monitor Screen

Back

DISP

MENU

SET

RECPLAY

C

0

7 8 9A

B

F

DE

GETTING READY

21

G H I

G Battery coverH ConnectorI Tripod screw hole

* Use this hole when attaching to a tripod.

Bottom USB CradleSimply placing your CASIO digital camera onto the USBcradle lets you perform the following tasks.

Battery charging (page 27) Automatic transfer of images to a computer (page 124) Viewing of images using the Photo Stand slideshow

feature (page 92).

1 Camera connector2 [USB] lamp3 [USB] button4 [CHARGE] lamp5 [PHOTO] button

PHOTO CHARGE USB

1

5 4

23

76

Back

6 [DC IN 5.3V](AC adaptor connector)

7 [USB](USB port)

Front

L

J

K

J StopperK Battery compartmentL Memory card slot

GETTING READY

22

Monitor Screen ContentsThe monitor screen uses various indicators and icons to keep you informed of the cameras status.

REC mode

QualityFINENORMALECONOMY

Battery capacity

Image size2048 1536 pixels1600 1200 pixels1280 960 pixels640 480 pixels

Movie Recording: recording time (seconds)

Date and timeEV value

Memory capacity(Remaining numberof storable images)

Built-in memory selected fordata storage.Memory card selected fordata storage.

Focus Mode indicatorNone Auto Focus

MacroInfinityManual Focus

Self-timerNone 1-Image

10s Self-timer 10 sec

2s Self-timer 2 sec

x3 Triple self-timer

Focus frame Focusing complete: Green Focusing failed: Red

REC modesSnapshotBest ShotMovie

GETTING READY

23

IMPORTANT! Some information may not display properly if you

display an image that was recorded using a differentdigital camera model.

Folder number/File number

QualityFINENORMALECONOMY

Battery capacity

Image size2048 1536 pixels1600 1200 pixels1280 960 pixels640 480 pixels

Date and time

Image protectionindicator

Built-in memoryselected for datastorage.Memory cardselected for datastorage.

PLAY mode

Flash Mode indicatorNone Auto

Flash OffFlash OnRed-eye reduction

If the camera detects that flash isrequired while auto flash isselected, the flash on indicatorwill appear when the shutterrelease button is pressed halfway.

White balanceindicator

None AutoSunlightShadeLight BulbFluorescentManual

Zoom indicatorLeft side indicates optical zoom.Right side indicates digital zoom.

Aperture value

Shutter speedvalue An out of range

aperture or shutterspeed causes thecorrespondingmonitor screenvalue to turnamber.

Digital zoom indicator

ISO sensitivity

PLAY mode file typeSnapshotMovie

GETTING READY

24

Indicatorson

(page 22)Histogram

on(page 75)

Indicatorsoff

Monitorscreen off

*

Changing the Contents of the MonitorScreenEach press of the [DISP] button changes the contents ofthe monitor screen as shown below.

* You cannot turn off the monitor screen in the following modes:PLAY mode, Best Shot mode, Movie mode, Macro mode.

Indicator LampsYou can find out the operational status of the camera andthe USB cradle at a glance by checking the color of theindicator lamps, and whether a lamp is lit or flashing. Fordetails, see Indicator Lamp Reference on page 156.

PHOTO CHARGE USB

DISP

MENU

SET

RECPLAY

Self-timer lamp Green operation lamp

[USB] lamp

[CHARGE] lamp

Red operation lamp

GETTING READY

25

Attaching the StrapAttach the strap to the strap ring as shown in theillustration.

IMPORTANT! Be sure to keep the strap around your wrist when

using the camera to protect against accidentallydropping it.

The supplied strap is intended for use with thiscamera only. Do not use it for any other purpose.

Never swing the camera around by the strap.

DISP

MENU

SET

RECPLAY

DISP

MENU

SET

RECPLAY

Power RequirementsYour camera is powered by a rechargeable lithium ionbattery (NP-20).

To load the battery

1. While pressing the battery cover on thebottom of the camera, slide the cover in thedirection indicated by the arrow, and thenswing it open.

GETTING READY

26

2. While pulling the stopper in the directionindicated by the arrow in the illustration, alignthe arrow mark on the battery with the arrowmark on the camera and slide the battery intothe camera.

Arrow marks

NP-20

Stopper

3. Swing the battery cover closed, and then slideit in the direction indicated by the arrow.

IMPORTANT! Use only the special NP-20 rechargeable lithium ion

battery to power this camera. Use of any other typeof battery is not supported.

The battery is not charged when you purchase thecamera. You need to charge the battery before usingthe camera for the first time (page 27).

Push the bottom of the battery, and make sure thatthe stopper securely locks the battery in place.

GETTING READY

27

To charge the battery

1. Connect the bundled AC adaptor to the [DC IN5.3V] connector of the USB cradle, and thenplug it in to a household power outlet. Note that the shape of the AC adaptor depends on

the area where you purchased the camera.

AC Adaptor

[DC IN 5.3V]USB Cradle

AC power cord

To remove the battery

1. Open the battery cover.2. Pull the stopper in the direction indicated by

the arrow. This will cause the battery to come part way out of

the slot.

Stopper

3. Release the stopper and pull the battery fromthe camera. Take care so you do not drop the battery.

GETTING READY

28

2. Turn off the camera.3. Set the camera onto

the USB cradle. Do not place the

camera onto the USBcradle while it is turnedon.

The [CHARGE] lamp onthe USB cradle shouldturn red, indicating thatcharging has started.When charging iscomplete, the[CHARGE] lamp willturn green.

4. After charging is complete, remove thecamera from the USB cradle.

PHOTO CHARGE USB

DISP

MENU

SET

RECPLAY

[CHARGE] lamp

NOTE The bundled AC adaptor is designed for operation

with any power supply in the range of 100V to 240VAC. Note, however, that the shape of the AC powercord plug varies according to country or geographicarea. If you plan to use the AC adaptor in ageographic area where the power receptacle shapeis different from that in your area, replace the ACpower cord with one of the other ones that comeswith the camera, or purchase a commerciallyavailable AC power cord that is compatible with thepower outlets in that area.

NOTE The AC adaptor is designed for operation on power

ranging from 100V AC to 240V AC. Note, however,that the shape of the power cord plug variesaccording to country or geographic area. It is up toyou to find out if the shape of the AC adaptor powercord plug is compatible with local power outlets whentraveling abroad.

AC Adaptor

[DC IN 5.3V]

USB Cradle

GETTING READY

29

If the [CHARGE] lamp starts flashing red, it meansthat an error occurs while charging. An error can becaused by any of the following: a problem with theUSB cradle, a problem with the camera, or a problemwith the battery or how it is loaded. Remove thecamera from the USB cradle and see if it worksnormally.

You can use the USB cradle to charge the camerasbattery, to exchange data with a computer over aUSB connection, or when using the Photo Standfeature only.

IMPORTANT! It takes about two hours to achieve a full charge.

Actual charging time depends on current batterycapacity and charging conditions.

Use only the USB cradle (CA-21) or the optionallyavailable charger unit (BC-10L) to charge the specialNP-20 rechargeable lithium ion battery. Never useany other charging device.

Use only the bundled AC adaptor. Never use anyother type of AC adaptor. Do not use optionallyavailable AD-C40, AD-C620 and AD-C630 ACadaptors with this camera.

Make sure that the camera connector of the USBcradle is securely inserted into the camerasconnector as far as it will go.

The [CHARGE] lamp may remain amber colored andthe charge operation may not start right away if youtry to charge immediately after using the camera(which causes battery to become warm) or when it istoo hot or too cold where you are performing thecharge operation. If this happens, simply wait untilthe battery reaches normal temperature. The[CHARGE] lamp will turn red and charging will startwhen the battery temperature returns to theallowable charging temperature range.

GETTING READY

30

Battery Life GuidelinesThe battery life guideline values given below indicate theamount of time at standard temperature (25C (77F)) untilpower automatically turns off due to battery failure. They donot guarantee that the battery will provide the amount ofservice indicated. Low temperatures and continued usereduce battery life.

Supported Battery: NP-20 (Rated Capacitance: 680mAh)

*1 Continuous Recording Conditions Normal temperature: 25C (77F) Flash: Off Monitor screen: On Image recorded about every 10 seconds using the

following operations: Zoom to full wide angle AutoFocus Zoom to full close-up Auto Focus Image recording

*2 Continuous Playback Conditions Normal temperature: 25C (77F) Scroll one image about every 10 seconds

Approximate Battery Life

75 minutes (450 shots)120 minutes

OperationContinuous Recording*1(Continuous Snapshot Recording)Continuous Playback*2

If the camera works normally

1. Continue using the camera until the currentcharge is used up, and then charge thebattery.

If the camera does not work normallyThis can mean there is a problem with how the battery isloaded.

1. Remove the battery from the camera andcheck the battery contacts for dirt. If thecontacts are dirty, wipe them clean with a drycloth.

2. Check to make sure that the AC adaptorspower cord is connected securely to thepower outlet and USB cradle. If the same symptoms occur again when you place

the camera on the USB cradle after taking the abovesteps, contact a CASIO authorized service center.

GETTING READY

31

Recording one image per minute under the aboveconditions reduces battery life to about one sixth of thatnoted above.

The above values are based a new battery starting from afull charge. Repeated charging shortens battery life.

Battery life is greatly affected by how much you use flash,zoom and other functions, and how long you leave powerturned on.

Tip to Make the Battery Last LongerIf you do not need the flash while recording, select (flash off) for the flash mode. See page 50 for moreinformation.

Low Battery IndicatorThe following shows how the battery capacity indicator onthe monitor screen changes as battery power is used. The

indicator means that remaining battery power is low.Note that you will not be able to record images while thebattery indicator is . Charge the battery immediatelywhenever either of these indicators appears.

Battery Level High Low

Indicator

GETTING READY

32

Power Supply PrecautionsNote the following precautions when handling or using thebattery and the optional charger unit.

Battery Handling Precautions SAFETY PRECAUTIONSBe sure to read the following Safety Precautions beforetrying to use the battery for the first time. Keep these safetyprecautions and all operating instructions on hand forfuture reference.

NOTES The term battery in this manual refers to the CASIO

NP-20 Rechargeable Lithium Ion Battery. The term optional charger unit in the following

precautions refers to the optionally available CASIOBC-10L Charger Unit.

Failure to observe any of the following precautionswhile using the battery creates the risk of overheating,fire, and explosion. Never use any other type of charger except the

optional charger unit specified for the battery. Never try to use the battery to power any other

device other than this camera. Never use or leave the battery near open flame. Never place the battery in a microwave oven, throw

it into fire, or otherwise expose it to intense heat. Make sure the battery is oriented correctly when you

load it into the camera or attach it to the optionalcharger unit.

Never carry or store the battery together with itemsthat can conduct electricity (necklaces, pencil lead,etc.)

Never try to take the battery apart, modify it in anyway, or expose it to strong impact.

Do not immerse the battery in fresh water or saltwater.

Do not use or leave the battery under directsunlight, in an automobile parked in the sun, or inany other area subject to high temperatures.

GETTING READY

33

PRECAUTIONS DURING USE The battery is designed for use with this CASIO digital

camera only. Use only the USB cradle that comes with the camera or

the specified optional charger unit to charge thebattery. Never use any other type of charger unit forcharging.

A new battery is not charged. Be sure to charge thebattery before using it for the first time.

Use of a battery in cold environments shortens theoperating time you can expect on a full charge. Chargethe battery in a location where the temperature is in therange of 10C to 35C (50F to 95F). Chargingoutside this temperature range can cause charging totake longer than normal or even cause charging to fail.

Very limited operation following a full charge indicatesthat the battery has reached the end of its service life.Replace the battery with a new one.

Never wipe the battery with thinner, benzene, alcohol,or other volatile agents or chemically treated rags.Doing so can cause deformation of the battery and leadto malfunction.

Should you ever notice leakage, strange odor, heatgeneration, discoloration, deformation, or any otherabnormal condition while using, charging, or storing abattery, immediately remove it from the camera oroptional charger unit and keep it away from open flame.

If the battery does not achieve full charge after thenormal charging time has passed, stop charging.Continued charging creates the risk of overheating, fire,and explosion.

Battery fluid can damage your eyes. Should batteryfluid get into your eyes accidentally, immediately rinsethem with clean tap water and then consult a physician.

Be sure to read page 27 of this Users Guide and theinstructions that come with the optional charger unitbefore using or charging the battery.

If the battery is to be used by young children, makesure that a responsible adult makes them aware of theprecautions and proper handling instructions and makesure that they handle the battery correctly.

Should fluid from the battery accidentally get ontoclothing or your skin, immediately rinse it off with cleantap water. Prolonged contact with battery fluid cancause skin irritation.

GETTING READY

34

BATTERY STORAGE PRECAUTIONS Make sure you remove the battery when you do not

plan to use the camera for a long time. A battery left inthe camera discharges very small amounts of powereven when power is turned off, which can lead to adead battery or the need for longer charging before thenext use.

Store the battery in a cool, dry place (20C (68 F) orlower).

USING THE BATTERY See page 27 of this manual or the instructions that

come with the optional charger unit for informationabout charging procedures and charging times.

When transporting a battery, keep it either loaded inthe camera or stored in its case.

USB Cradle and AC Adaptor Precautions Never use an electrical outlet whose voltage

is outside the rating marked on the ACadaptor. Doing so can create the danger offire or electric shock. Use only the bundledAC adaptor specified for this camera.

Do not allow the AC adaptor cord to becomecut or damaged, do not place heavy objectson it, and keep it away from heat. A damagedpower cord creates the risk of fire and electricshock.

Never try to modify the AC adaptor cord, orsubject it to severe bending, twisting, orpulling. Doing so creates the risk of fire andelectric shock.

Never touch the AC adaptor while your handsare wet. Doing so creates the risk of electricshock.

Do not overload extension cords or walloutlets. Doing so creates the danger of fireand electric shock.

Should the cord of the AC adaptor becomedamaged (exposed internal wiring), request areplacement from a CASIO authorized servicecenter. A damaged AC adaptor cord createsthe danger of fire or electric shock.

Caution!

GETTING READY

35

Make sure you always remove the camera from the USBcradle before connecting or disconnecting the ACadaptor.

Charging, USB data communication, and using the PhotoStand feature can cause the AC adaptor to becomewarm. This is normal and does not indicate malfunction.

Unplug the AC power cord from the power outletwhenever you are not using it.

Never place a blanket or any other cover on the ACadaptor. Doing so creates the risk of fire.

Turning the Camera On and OffPress the power button to turn the camera on and off.Pressing the power button to turn on the camera causesthe green operation lamp to light temporarily. Press thepower button again to turn off the camera.

Green operation lamp

ON/OFF

Power button

IMPORTANT! If camera power is turned off by the Auto Power Off

feature, press the power button to turn it back onagain.

Turning on camera power while the REC mode isselected by the mode selector causes the lens toextend from the camera. Make sure there is nothingin front of the camera that can be hit by the lenswhen you turn on the camera.

GETTING READY

36

Configuring Power Saving SettingsYou can configure the settings described below toconserve battery power.

Sleep : Automatically turns off the monitor screenif no operation is performed for a specifiedamount of time in the REC mode.Performing any button operation causesthe monitor screen to turn back on.

Auto Power Off : Turns off power if you do not perform anyoperation for a specified amount of time.

1. Turn on the camera, and then align the modeselector with REC or PLAY.

2. Press [MENU].3. Use [] and [] to select the Set Up tab.4. Use [] and [] to select the feature whose

setting you want to configure, and then press[SET].

5. Use [] and [] to change the currentlyselected setting, and then press [SET]. Available Sleep settings are: 30 sec, 1 min, 2 min,

and Off. Available Auto Power Off settings are: 2 min and

5 min. Note that the Sleep feature does not operate in the

PLAY mode. Pressing any button while the camera is in the Sleep

state immediately turns the monitor screen back on. The Auto Power Off and Sleep features are disabled

in the following cases. When the camera is connected to a computer or

some other device through the USB cradle While a slideshow is in progress

To configure this feature: Select this setting:Sleep SleepAuto Power Off Auto Power Off

See page 37 for information about how to usemenus.

GETTING READY

37

Using the On-screen MenusPressing [MENU] displays menus on the monitor screenthat you can use to perform various operations. The menuthat appears depends on whether you are in the RECmode or the PLAY mode. The following shows an examplemenu procedure in the REC mode.

1. Turn on the camera,and then align themode selector withREC to enter theREC mode. If you want to enter the

PLAY mode instead,you would align themode selector withPLAY.

MENU

RECPLAY

Mode selector

2. Press [MENU].

SettingsSelection cursor (indicates thecurrently selected item)

Tab

DISP

MENU

SET

[MENU]

[SET]

[][ ][][ ]

GETTING READY

38

3. Press [] or [] to select the tab you want,and then press [SET] to move the selectioncursor from the tab to the settings.

4. Use [] and [] toselect the featurewhose setting youwant to configure,and then press []. Instead of pressing [],

you could also press[SET].

5. Use [] and [] to change the currentlyselected setting.

Menu Screen Operations

When you want to do this:Move between tabsMove from the tab to thesettingsMove from the settings tothe tabMove between the settingsDisplay the optionsavailable for a settingSelect an optionRegister an optionselection and exit the menuscreen

Register an optionselection and return to themenu screen

Exit the menu screen

Do this:Press [] and [].

Press [].

Press [].Press [] and [].

Press [] or press [SET].Press [] and [].

Press [SET].

Press [].

Press the [MENU] button.

Example: To select theREC Modeitem.

GETTING READY

39

Configuring Display Language and ClockSettings

Be sure to configure the following settings before using thecamera to record images.

Display language Home city Date Style Date and time

Note that the current date and time settings are used bythe camera to generate the date and time that are storedalong with image data, etc.

6. Perform one of the following operations toapply the setting you configured.

To do this:Apply the setting and exitthe menu screen.Apply the setting andreturn to feature selectionin step 4.Apply the setting andreturn to tab selection instep 3.

Perform this key operation:

Press [SET].

Press [].

1. Press [].2. Use [] to move back up to

tab selection.

See Menu Reference on page 154 for more informationabout menus.

GETTING READY

40

To configure display language and clocksettings

1. Press the power button to turn on the camera.2. Use [], [], [], and

[] to select thelanguage you want,and then press [SET].

: JapaneseEnglish : EnglishFranais : FrenchDeutsch : GermanEspaol : SpanishItaliano : ItalianPortugus : Portuguese

: Chinese (Complex): Chinese (Simplified): Korean

IMPORTANT! The cameras clock settings are cleared whenever

power is totally cut off. This can happen if the batterygoes dead while the camera is not being suppliedpower by the USB cradle. The clock setting screenwill appear automatically the next time you turn onpower after the settings are cleared. Set the dateand time before using the camera.

The current date and time settings will be cleared ifthe battery remains dead without being charged forabout two days.

Recording images without configuring the clocksettings causes incorrect time information to beregistered. Be sure to configure the clock settingsbefore using the camera.

GETTING READY

41

6. Use [] and [] tochange the date formatsetting, and then press[SET].

Example: October 23, 2003

To do this:Change the setting at the currentcursor locationMove the cursor between settingsToggle between 12-hour and 24-hour timekeeping

Do this:

Press [] and [].Press [] and [].

Press [DISP].

Select this format:YY/MM/DDDD/MM/YYMM/DD/YY

To display the date like this:03/10/2323/10/0310/23/03

7. Set the current dateand the time.

3. Use [], [], [], and[] to select thegeographical areawhere you live, andthen press [SET].

4. Use [] and [] toselect the name of thecity where you live,and then press [SET].

5. Use [] and [] to select the summer time(DST) setting you want, and then press [SET].

When you want to do this:Keep time using summer time(Daylight Saving Time)Keep time using standard time

Select this setting:

On

Off

GETTING READY

42

8. Press [SET] to register the settings and exitthe setting screen.

43

BASIC IMAGE RECORDING

3. Compose the imageon the monitor screenso the main subject iswithin the focusframe. The focusing range of

the camera in the AutoFocus mode isapproximately 40cm(1.3 feet) to infinity ()(page 57).

You can compose images using either the monitorscreen or the optical viewfinder (page 47).

When using the optical viewfinder to composeimages, you can use the [DISP] button to turn off themonitor screen and conserve battery power.

BASIC IMAGE RECORDINGThis section describes the basic procedure for recording animage.

Recording an ImageYour camera automatically adjusts shutter speed inaccordance with the brightness of the subject. Images yourecord are stored in the cameras built-in memory, or to amemory card if you have one loaded in the camera. When an optionally available SD memory card or

MultiMediaCard (MMC) is loaded in the camera, imagesare stored on the card (page118).

1. Press the powerbutton to turn on thecamera.

This causes an imageor a message to appearon the monitor screen.

2. Align the modeselector with REC. This enters the REC

mode for imagerecording.

ON/OFF

Power button

MENU

RECPLAY

Mode selector

1200120016001600NORMALNORMAL

9999

0303/1212/24241212:5858

IN

Focus frame

44


Shutter releasebutton

4. Press the shutter releasebutton half way to focus theimage. When you press the shutter

release button half way, thecameras Auto Focus featureautomatically focuses the image,and displays the shutter speedand aperture values.

You can tell whether theimage is focused byobserving the focus frameand the green operationlamp.

Green operation lamp

It means this:

The image is in focus.

The image is not in focus.

When you see this:Green focus frameGreen operation lampRed focus frameFlashing green operation lamp

Make sure you are notblocking the lens or theflash with your fingerswhile recording animage.

Operation Lamp and Focus Frame Operation

Lens

Flash

45


5. After making sure that theimage is focused properly,press the shutter releasebutton the rest of the waydown to record. The number of images that can

be stored in memory depends onthe resolution setting you areusing (page 164).

Press the shutter release button gently to avoidcamera movement.

Shutter releasebutton

Recording Precautions Never open the battery cover or place the camera onto

the USB cradle while the green operation lamp isflashing. Doing so not only causes the current image tobe lost, it can also corrupt images already stored in filememory and even lead to malfunction of the camera.

Never remove the memory card while an image is beingrecorded to the memory card.

Fluorescent lighting actually flickers at a frequency thatcannot be detected by the human eye. When using thecamera indoors under such lighting, you may experiencesome brightness or color problems with recorded images.

When Auto is selected for the ISO sensitivity setting(page 76), the camera automatically adjusts its sensitivityin accordance with the brightness of the subject. This cancause some static noise to appear in images of relativelydark subjects.

When recording a dimly lit subject while Auto is selectedfor the ISO sensitivity setting (page 76), the cameraincreases sensitivity and uses a slower shutter speed.Because of this, you need to guard against cameramovement if you have flash turned off (page 50).

If unwanted light is shining on the lens, shade the lenswith your hand when recording the image.

46


About the REC Mode Monitor Screen The image shown on the monitor screen in the REC

mode is a simplified image for composing purposes. Theactual image is recorded in accordance with the imagequality setting currently selected on your camera. Theimage saved in file memory has much better resolutionand detail than the REC mode monitor screen image.

Certain levels of subject brightness can cause theresponse of the REC mode monitor screen to slow down,which causes some static noise in the monitor screenimage.

About Auto Focus Auto Focus tends not to work well if the camera is moved

during recording, or when recording the types of subjectslisted below. Solid color walls or objects with little contrast Strongly backlit objects Polished metal or other brightly reflective objects Venetian blinds or other horizontally repeating patterns Multiple images that are varying distances from the

camera Subjects in poorly lit areas Moving subjects

Note that a green operation lamp and focus frame do notnecessarily guarantee that an image is in focus.

If Auto Focus does not produce the results you want forsome reason, try using focus lock (page 60) or manualfocus (page 59).

47


Using the Optical ViewfinderYou can conserve battery power by turning off thecameras monitor screen (page 24) and using the opticalviewfinder to compose images.

IMPORTANT! The frame that is visible inside of the viewfinder

indicates the image recorded at a distance of aboutone meter (3.3). When the subject is closer than onemeter, the recorded image will be different from whatyou see inside the viewfinder frame.

The monitor screen turns on automatically wheneveryou select the Macro mode or Manual Focus mode.Always use the monitor screen to compose imagesin these modes.

Viewfinder frameShort distanceto subject

48


Using ZoomYour camera is equipped with two types of zoom: opticalzoom and digital zoom.

Optical ZoomThe range of the optical zoom factor is shown below.

Optical Zoom Factor Range: 1X to 3X

1. In the REC mode, pressthe zoom button tochange the zoom factor.

Zoom out Zoom in

MENU

REC

Zoom button

2. Compose the image and then press theshutter release button.

NOTES The optical zoom factor also affects the lens

aperture. Use of a tripod is recommended to protect against

hand movement when using the telephoto setting(zoom in).

Press this side of the zoom button: (Wide Angle) (Telephoto)

To do this:Zoom outZoom in

49


Digital ZoomDigital zoom is activated after you reach the maximumoptical zoom factor (3X). It enlarges the part of the imageat the center of the image screen. The range of the digitalzoom factor is shown below.

Digital Zoom Factor Range: 3X to 12X(in combination with opticalzoom)

1. In the REC mode, press [MENU].2. Use [] and [] to select the REC tab.3. Use [] and [] to select Digital Zoom, and

then press [].4. Select On, and then press [SET].

Selecting Off disables digital zoom.

5. Hold down the (Telephoto) zoombutton to increase theoptical zoom factor. When the digital zoom

factor reaches itsmaximum value (3X), itstops momentarily. Keepthe (Telephoto)zoom button depressedand zoom will switchover to digital zoomautomatically.

Switching to digital zoom causes the zoom indicatorto appear on the monitor screen. The zoom indicatorshows the current approximate zoom factor.

6. Compose the image and then press theshutter release button.

Zoom indicator

Digital zoom indicator

1x 3x 12xCurrent zoom factor

Optical ZoomDigitalZoom

50


Using the FlashPerform the following steps to select the flash mode youwant to use.

1. In the REC mode, press [MENU].2. Press [] ( ) to select

the flash mode. Each press of [] ( )

cycles through the flashmode settings shown belowon the monitor screen.

Flash mode indicator

DISP

MENU

SET

[ ] ( )

IMPORTANT! Digital zoom is disabled whenever the monitor

screen is turned off (page 24). Using digital zoom can cause degradation of the

recorded image.

51


3. Record the image.

IMPORTANT! The flash unit of this camera fires a number of times

when you record an image. The initial flashes arepre-flashes, which the camera uses to obtaininformation that it uses for exposure settings. Thefinal flash is for recording. Make sure that you keepthe camera still until the shutter releases.

Image recording may not be performed if you pressthe shutter release button while the red operationlamp is flashing.

To do this:Have the flash fire automatically whenrequired (Auto Flash)Turn off the flash (Flash Off)

Always fire the flash (Flash On)Fire a pre-flash followed by imagerecording with flash, reducing thechance of red-eye in the image (Red-eye reduction)In this case, the flash fires automaticallywhen required

Select this setting:

None

About Red-eye ReductionUsing the flash to record at night or in a dimly lit room cancause red spots inside the eyes of people who are in theimage. This is caused when the light from the flash reflectsoff of the retina of the eye. When red-eye reduction isselected as the flash mode, the camera performs two pre-flash operations, one designed to cause the irises in theeyes of any people in the image to close, and one for theAuto Focus operation. This is followed by another flashoperation for actual recording of the image.

IMPORTANT! Note the following important points when using red-eye reduction. Red-eye reduction does not work unless the people

in the image are looking directly at the camera duringthe pre-flash. Before pressing the shutter releasebutton, call out to the subjects so they all look at thecamera while the pre-flash operation is performed.

Red-eye reduction may not work very well if thesubjects are located far away from the camera.

52


Flash Unit StatusYou can find out the current flash unit status by pressingthe shutter release button half way and checking themonitor screen and red operation lamp.

Red operation lamp*

The indicator is alsoshown on the monitorscreen when the flash unitis ready to fire.

* Red operation lamp

It means this:

Flash unit is chargingFlash unit is ready to fire

When the red operationlamp is this:FlashingLit

Flash PrecautionsTake care that your fingers donot block the flash when youhold the camera. Covering theflash with your finger cangreatly reduce itseffectiveness.

You may not be able to achieve the desired results usinga flash if the subject is too close or too far away.

The flash takes anywhere from a few seconds to as longas 10 seconds to attain full charge after being fired. Theactual time required depends on the battery level,temperature, and other conditions.

The flash does not fire in the Movie mode. This isindicated by (Flash Off) on the monitor screen.

The flash unit may not be able to charge when batterypower is low. Low battery power is indicated by (FlashOff) on the monitor screen, and when the flash fails to fireproperly resulting in poor image exposure. When thesesymptoms occur, charge the cameras battery as soon aspossible.

When the red-eye reduction mode ( ) is selected, flashintensity is adjusted automatically in accordance with theexposure. The flash may not fire at all when the subject isbrightly lit.

Flash

53


Using the Self-timerThe self-timer lets you select either a 2-second or 10-second delay of the shutter release after you press theshutter release button. A Triple Self-timer feature lets youperform three consecutive self-timer operations to recordthree images.

1. In the REC mode, press [MENU].2. Use [] and [] to select the REC tab.3. Use [] and [] to select Self-timer, and

then press [].4. Use [] and [] to select the self-timer time

you want to use, and then press [SET]. Selecting Off in step 4 disables the self-timer.

White balance is fixed while the flash is being used, sosunlight, fluorescent lighting, or other sources ofillumination in the immediate area may affect the coloringof the recorded image.

54


With the Triple Self-timer, the camera records aseries of three images in the sequence describedbelow.

1. The camera performs a 10-second countdown andthen records the first image.

2. The camera prepares to record the next image.The amount of time required for preparationdepends on the cameras current Size andQuality settings, the type of memory (built-in orcard) you are using for image storage, andwhether or not the flash is charging.

3. After preparation is complete, the indicator 1secappears on the monitor screen, and anotherimage is recorded one second later.

4. Steps 2 and 3 are repeated once more to recordthe third image.

To do this:Specify a 10-second self-timerSpecify a 2-second self-timerSpecify Triple Self-timerDisable the self-timer

Select this setting:10 sec2 secX3Off

5. Record the image. When you press the

shutter release button,the self-timer lampflashes and the shutterreleases after the self-timer reaches the endof its countdown.

You can interrupt anongoing self-timercountdown by pressingthe shutter releasebutton while the self-timer lamp is flashing.

NOTE The 2 sec self-timer setting is best when shooting

with a slow shutter speed, because it helps to avoidblurring of images due to hand movement.

Self-timer lamp

55


Specifying Image Size and QualityYou can specify the image size and image quality to suitthe type of image you are recording.

To specify the image size

1. In the REC mode, press [MENU].2. Use [] and [] to select the REC tab.3. Use [] and [] to select Size, and then

press [].4. Use [] and [] to select the setting you

want, and then press [SET].2048 x 1536 : 2048 x 1536 pixels1600 x 1200 : 1600 x 1200 pixels1280 x 960 : 1280 x 960 pixels640 x 480 : 640 x 480 pixels

NOTE Use 2048 x 1536 when you plan to produce a large

print of the image. Use 640 x 480 when you need toeconomize on space because you plan to sendimages in e-mail, etc.

56


To specify image quality

1. In the REC mode, press [MENU].2. Use [] and [] to select the REC tab.3. Use [] and [] to select Quality, and then

press [].4. Use [] and [] to select the setting you

want, and then press [SET].

NOTE Use the Fine setting when image quality is your top

priority and file size is secondary. Conversely, usethe Economy setting when file size is your toppriority and image quality is secondary.

IMPORTANT! Actual file size depends on the type of image you

record. This means that the remaining imagecapacity noted on the monitor screen may not beexactly accurate (pages 22 and 164).

Select this setting:FineNormalEconomy

To get this:Very high quality, but large file sizeNormal qualitySmall file size, but low quality

exz3_e_1

Documents

Transcript of exz3_e_1