© 2014 Universal Lighting Technologies | 1 June 18, 2014

Programming Cradle Setup & Operation

© 2014 Universal Lighting Technologies | 2 June 18, 2014

ULT LED Tunable Drivers

Tuning Table

ULT Driver Output Tuning

Digital Protocol via 0-10V leads

Tuning table specific to each model – table in spec sheet

Two tuning devices will be available

Handheld tuner

Multi-driver cradle

© 2014 Universal Lighting Technologies | 3 June 18, 2014

LED Driver Tuning Devices

Handheld Tuning Device Programs any ULT tunable LED driver

Dial settings provide tuning table values (00 = 100%)

Multi-driver production programming system Program 5 LED driver simultaneously

Replaceable programming tray supporting multiple driver styles

Tunes UNV (120V-277V) and 347Vdrivers

Label printer support for on-demand label printing

Website downloadable tuning tables updates for new drivers

Control Software (Windows® XP/7/8)

Programming Cradle Label Printer (separate) Zebra #05100GS06407 Pesa Labeling #753750

© 2014 Universal Lighting Technologies | 4 June 18, 2014

Hardware Setup

Back Panel Standard IEC-320-C14 plug inlet

Power Switch

USB Male A-Type ~6 ft connector cable

D-Sub 9 pin ~6 ft connector cable

1 Connect Power cord

2 Connect USB cable to host computer available USB port

3 Connect D-Sub 9-pin connector to printer

D-Sub Connector 4 Toggle power switch to “On”

Front panel indicator light should be illuminated

© 2014 Universal Lighting Technologies | 5 June 18, 2014

Software Setup

System Requirements

OS: Windows® XP/7/8

RAM: > 512 Mbytes

Hard Drive Space: > 5 MBytes

One available USB 2.0 port

1 Extract file(s) from Zip file

2 Run “setup” file

Click “Next” and follow setup wizard instructions

© 2014 Universal Lighting Technologies | 6 June 18, 2014

Software Setup (cont’d)

3 Once installation is complete launch the application

4 Check communication to the programming cradle

You should see this icon on the windows desktop screen to launch the software from

5 Select the “file” menu item

6 Select the “Update Model List (Internet)” menu item

The lower right corner of the Tuning Utility should show the message “Programming Nodes: 5”

© 2014 Universal Lighting Technologies | 7 June 18, 2014

Loading LED drivers

5 LED Driver Programming Blocks

LED drivers are loaded upside down to mate the connector with the block pins

Input side of LED driver must mate up with blocks toward front of programming cradle (blocks w/ pins)

Programming Blocks Contain input power and programming pins – only one block for this programming tray

Blocks w/ electrical pins

© 2014 Universal Lighting Technologies | 8 June 18, 2014

Loading LED drivers

LED Driver Placement

The Programming Blocks Contain input power and programming pins

The end of the driver with the 0-10V leads must be placed into the block with the contact pins

To place the drivers into the blocks

Place the driver over the back block and the front of the driver slightly above the front block. Rotate the driver down into the front block pushing down until the driver sits firmly on the blocks.

© 2014 Universal Lighting Technologies | 9 June 18, 2014

Caution High Voltage

Caution High Voltage inside Programmer

There are high voltages applied to the driver while programming

When the door is open the door switch will shut off the input power to drivers. Once closed the drivers will be powered at 277V (to accommodate UNV (120V-277V) and 347V drivers).

© 2014 Universal Lighting Technologies | 10 June 18, 2014

LED Driver Programming

1 Once installation is complete Launch the application

2 Select the desired driver to program

3 Select the “program” value from the dropdown menu

You should see this icon on the windows desktop screen to launch the software from

NOTE: The current programming tray supports the D10CC55UNVT-C and D15CCUNVT-C models only. Future trays will support the additional models shown.

4 Click the “go to programming” button

© 2014 Universal Lighting Technologies | 11 June 18, 2014

LED Driver Programming

1 Click the “Program model…” button

2 Check that all slots indicators are “green”

Programming Screen

In the programming screen the slot indicators should show “no color” for all slots that have an LED driver in place.

A “yellow” indicator color for any slot means there is a problem with communication to that slot and programming will not occur.

To program all loaded LED Drivers

3 If you need to change the programmed value, simply click the “Back to…” button

© 2014 Universal Lighting Technologies | 12 June 18, 2014

LED Driver Programming

Post Programming

After roughly 3 – 5 seconds the programming process should complete and all the slots with drivers should have a “green” indicator

If one or more of the drivers did not program correctly a “red” indicator will appear.

Additional drivers can be loaded and programmed from this screen, although the indicator color will not change until the “Program model…” button is clicked again.

© 2014 Universal Lighting Technologies | 13 June 18, 2014

Labeling LED Drivers

1 Click the “Print Labels” button

Programmed LED Driver Labels

The programmer will print labels for each of the LED drivers that were programmed

Each label will be printed with the program value and nominal output current per the value selected.

To print the labels

The printer will print a label for each click of the “Print Labels” button.

The label is intended to be placed over the Iout/program box area at the left end of the driver.

© 2014 Universal Lighting Technologies | 14 June 18, 2014

Programming Tray (Future Option)

Driver Programming Tray

The LED driver programming tray is specific to each driver case style and connector wiring configuration.

This will be an orderable part and can be changed easily.

1 Disconnect power and loosen the 4 corner fasteners

2 Pull the tray partially out of the housing

To replace programming tray

3 Disconnect the 2 cables from the bottom connections

4 Connect new tray, place back into housing and tighten fasteners