CONSTRUCT 12/948

STATUS OF ETAGs, GUIDELINES FOR EUROPEAN TECHNICAL APPROVALS, AND ETAs

15 October 2012

1. Endorsed ETAGsAt present there are 32 endorsed guidelines with a total of 65 Parts. See summary table in Annex 1.

2. Endorsed Technical Reports

36 Technical Reports are available. See summary table in Annex 2.

3. Pending Guidelines

There are 3 pending guidelines (see details in Annex 1):

- ETAG 028 Fire retardant products: endorsed by EOTA; sent to EC services for final endorsement

- ETAG 030 Dowels for structural joints: in final stage, to be finished this year - ETAG 032 Expansion joints for bridges: endorsed by EOTA; sent to EC services for final

endorsement

4. Progress files in preparation

At present there are 10 Progress files in preparation, to be finished this year or for 2 of them at the beginning of the next year, and 2 already sent to EC services (see details in Annex 1):

- ETAG 001 Metal anchors for use in concrete- ETAG 002 Structural sealant glazing systems (already sent to EC services )- ETAG 003 Internal partitions kits (already sent to EC services )- ETAG 004 ETICs- ETAG 006 Systems of mechanically fastened flexible roof waterproofing membranes- ETAG 007 Timber building kits- ETAG 008 Prefabricated stair kits- ETAG 013 Post-tensioning kits for pre-stressing of structures- ETAG 015 Three dimensional nailing plates- ETAG 018 Fire protective products- ETAG 026 Fire stopping and fire sealing products- ETAG 027 Falling rock protection kits

5. Issued ETAs

3030 ETAs had been issued until 6 September 2012, 2475 based on ETAGs and 555 based on 9.2 procedures (CUAPs).

European Organisation for Technical ApprovalsEuropäische Organisation für Technische ZulassungenOrganisation Européenne pour l’Agrément Technique

Some 260 CUAPs or their amendment have been endorsed at present.

Annex 1. ETAGs status on 15.10.2012

ETAG ETAG Title Part (and version) Observations

ETAG 001 Metal Anchors for Use in Concrete

Part 1: General (Amend. November 2006)

Progress File ready by the end of this year.

1 additional annex on seismic actions ready by the end of this year.

Part 2: Torque-Controlled Expansion Anchors (Amend. November 2006)

Part 3: Undercut Anchors (Amend. August 2010)

Part 4: Deformation-Controlled Expansion Anchors (Amend. November 2006)

Part 5: Bonded Anchors (2nd Amend. February 2008)

Part 6: Anchors for multiple use for non-structural applications (Amend. January 2011)

Annex A: Details of test (2nd Amend. November 2006)

Annex B: Tests for admissible service conditions detailed information (2nd Amend. November 2006)

Annex C: Design methods for anchorages (3rd Amend. August 2010)

ETAG 002Structural Sealant Glazing Systems

Part 1: Supported and unsupported systems (Amend. October 2001)

Progress File of Part 1 sent to EC for endorsement (11/07/2012)Part 2 : Coated Aluminium Systems (January 2002)

Part 3 : Systems incorporating profiles with thermal barrier (March 2002)

ETAG 003 IPK Internal Partition Kits for use as Non-Loadbearing Walls (December 1998) Progress File sent to EC for endorsement (11/04/2012)

ETAG 004 amended ETICS External Thermal Insulation Composite Systems with Rendering (Progress File August 2011) 2nd Progress File ready by the end of this year

ETAG 005 Liquid Applied Roof Waterproofing Kits

Part 1: General (Revision March 2004)

Part 2: Specific stipulations for Kits based on Polymer Modified Bitumen Emulsions and Solutions (Revision March 2004)Part 3: Specific stipulations for Kits based on Glass Reinforced Resilient Unsaturated Polyester Resin (Revision March 2004)Part 4: Specific stipulations for Kits based on Flexible Unsaturated Polyester (Revision March 2004)

ETAG ETAG Title Part (and version) Observations

Part 5: Specific stipulations for Kits based on Hot Applied Polymer Modified Bitumen (Revision March 2004)

Part 6: Specific stipulations for Kits based on Polyurethane (Revision March 2004)

Part 7: Specific stipulations for Kits based on Bitumen Emulsions and Solutions (Revision March 2004)

Part 8: Specific stipulations for Kits based on Water Dispersiable Polymers (Revision March 2004)

ETAG 006 Systems of Mechanically Fastened Flexible Roof Waterproofing Membranes (March 2000) Progress File ready by the end of this year

ETAG 007 Timber Frame Building Kits (April 2001) Progress File ready by the end of this year

ETAG 008 Prefabricated Stair Kits (January 2002) Progress File ready by the end of this year or the beginning of next year

ETAG 009 Non load-bearing permanent shuttering kits/systems based on hollow blocks or panels of insulating materials and sometimes concrete (June 2002)

ETAG 010 Self Supporting Translucent roof Kits (September 2002)

ETAG 011 Light Composite Wood-based Beams and Columns (January 2002)

ETAG 012 Log Building Kits (June 2002) Merging with Progress File ETAG 007

ETAG 013 Post-Tensioning Kits for prestressing of Structures (June 2002) Progress File ready by the end of this year or the beginning of next year

ETAG 014 Plastic Anchors for ETICS (Amended February 2011)

ETAG 015 Three Dimensional Nailing Plates (September 2002) Progress File ready by the end of this year

ETAG 016Self-supporting Composite Light Weight Panels

Part 1: General (November 2003)

Part 2: Specific aspects relating to Self-supporting Composite Lightweight Panels for use in roofs (November 2003)Part 3: Specific aspects relating to Self-supporting composite lightweight panels for use in external walls and claddings (February 2005)Part 4: Specific aspects relating to Self-supporting Composite Lightweight Panels for use in internal walls and ceilings (July 2004)

ETAG 017 Veture Kits - Prefabricated Units for External Wall Insulation (November 2005)

ETAG 018 Fire protective products

Part 1: General (November 2004) Progress File of Parts 1 and 3 ready by the end of this year

ETAG ETAG Title Part (and version) Observations

Part 2: Reactive Coatings for Fire Protection of Steel Elements (Progress File November 2011)

Part 3: Renderings and Rendering Kits intended for Fire Resisting Applications (January 2006)

Part 4: Fire protective board, slab and mat products and kits (version December 2011)

ETAG 019 Pre-fabricated wood-based loadbearing stressed skin panels (November 2004)

ETAG 020

Plastic Anchors for multiple use in concrete and masonry for non-structural applications

Part 1: General (amended version March 2012)

Part 2: For use in normal weight concrete (amended version March 2012)

Part 3: For use in solid masonry (amended version March 2012)

Part 4: For use in hollow or perforated masonry (amended version March 2012)

Part 5: For use in autoclaved aerated concrete (amended version March 2012)

Annex A: Details of tests (amended version March 2012)

Annex B (informative): Recommendations for tests to be carried out on construction works (amended version March 2012)

Annex C: Design methods for anchorages (amended version March 2012)

ETAG 021 Cold Storage Premises kits

Part 1: Cold Storage Room Kits (September 2005)

Part 2: Cold Storage Building Envelope and Building Kits (October 2005)

Annexes Part 1 (September 2005)

ETAG 022 Watertight covering kits for wet room floors and or walls

Part 1: Liquid Applied Coverings with or without wearing surface (April 2007)

Part 2: Kits based on flexible sheets (November 2010)

Part 3: Kits based on inherently watertight boards (November 2010)

Annex A: Water tightness around penetrations and other details in wet room floors with flexible substrate (May 2005)

ETAG ETAG Title Part (and version) Observations

Annex B: Impermeability when subjected to movement of the underlying material - Tensile and shear loading (May 2005)

Annex C: Test for scratching resistance (May 2005)

Annex D: Waterproofing in liquid form: applicability and thickness of finished membrane (March 2005)

Annex E: Walls in wet rooms: water tightness and resistance to water and moisture of walls with flexible substrate (November 2005)Annex F: Water tightness around penetrations and other details in wet room walls with flexible substrate (October 2005)Annex G: Water tightness around penetrations and other details in wet room walls and floors with rigid substrates (May 2005)

Annex H: Paint systems for walls without wearing surface (October 2006)

Annex I: Mounting and fixing rules for the reaction to fire testing (November 2010)

ETAG 023 Prefabricated Building Units (August 2006)

ETAG 024 Concrete Frame Building Kits (January 2006)

ETAG 025 Metal Frame Building Kits (May 2006)

ETAG 026Fire Stopping and Fire Sealing Products

Part 1: General (January 2008)

Progress File of Part 1 ready by the end of this year

Revision of the Addendum to Part 2 on Model ETA sent to EC for endorsement (30/07/2012)

Part 2: Penetration Seals (Progress File August 2011)

Part 3 : Linear Joint and Gap Seals (Progress File August 2011)

Part 4: Reactive and Mechanical Air Transfer Grilles, (Fire resistant and Cold Smoke Control Fire Resistant Types) (May 2012)

Part 5 : Cavity Barriers (February 2011)

ETAG 027 Falling Rock Protection Kits Edition (February 2008) Progress File ready by the end of this year

ETAG 028 Fire retardant products Guideline sent to EC for endorsement (24/07/2012)

ETAG 029 Metal Injection Anchors for use in Masonry (June 2010)

ETAG ETAG Title Part (and version) Observations

Annex A: Details of tests (June 2010)

Annex B (informative): Recommendations for tests to be carried out on construction works (June 2010)

Annex C: Design methods for anchorages (June 2010)

ETAG 030 Dowels for structural joints Parts 1 to 3 Guideline ready by the end of this year

ETAG 031 Inverted Roofs Insulation Kits

Part 1: General (November 2010)

Part 2: Insulation with protective Finish (November 2010)

ETAG 032 Expansion joints for bridges Parts 1 to 8 Guideline sent to EC for endorsement (18/07/2012)

ETAG 033 Liquid applied bridge deck waterproofing kits (July 2010)

ETAG 034 Cladding Kits Part 1: Ventilated cladding kits comprising cladding components and associated fixings (April 2012)

Part 2: cladding kits comprising cladding components, associated fixings, subframe and possible insulation layer (April 2012)

ETAG 035 Ultra Thin Layer Asphalt Concrete (May 2011)

Annex 2. Endorsed EOTA Technical Reports on 15.10.2012

EOTA TR EOTA TR Title Date001 Determination of impact resistance of panels and panels assemblies Feb 2003002 Test methods for Light Composite Wood-based Beams and Columns Oct 2000003 Determination of the watertightness May 2004004 Determination of the resistance to delamination May 2004

005 Determination of the resistance to wind loads of partially bonded roof waterproofing membranes May 2004

006 Determination of the resistance to dynamic indentation May 2004007 Determination of the resistance to static indentation May 2004008 Determination of the resistance to fatigue movement May 2004009 Determination of the resistance to sliding May 2004010 Exposure procedure for artificial weathering May 2004011 Exposure procedure for accelerated ageing by heat May 2004012 Exposure procedure for accelerated ageing by hot water May 2004013 Determination of crack-bridging capability May 2004

014 Exposure procedure for accelerated ageing of glass reinforced unsaturated polyester resins by two-hour water boil May 2004

015 Principles for the static calculation of connections made with Three-Dimensional Nailing Plates, with examples Feb 2002

016 Method of Testing Three-Dimensional Nailing Plates, with examples Feb 2002

017 Worked example calculation of characteristic load-carrying capacities of 90° angle bracket with a rib Feb 2002

018 Assessment of torque controlled bonded anchors March 2003

019 Calculation models for prefabricated wood-based Loadbearing stressed skin panels for use in roofs Feb 2005

020 Evaluation of Anchorages in Concrete concerning Resistance to Fire May 2004021 Reaction to fire requirements for small components June 2005

022 Determination of the resistance to the passage of chloride ions through a waterproofing layer subjected to indentation by aggregate

November 2007

023 Assessment of post-installed rebar connections November 2006

024 Characterisation, Aspects of Durability and Factory Production Control for Reactive Materials, Components and Products

November 2006

024 am. Characterisation, Aspects of Durability and Factory Production Control for Reactive Materials, Components and Products July 2009

025 Determination of point thermal transmittance of plastic anchors for the anchorage of external thermal insulation composite systems (ETICS) June 2007

026 Evaluation of plate stiffness from plastic anchors for fixing of external thermal insulation composite systems with rendering (ETICS) June 2007

029 am. Design of Bonded Anchors September 2010

030 Factory made boards and products formed by moulding of a silicate polystyrene composite for thermal and or acoustical insulation Oct 2008

031 Fire Resistance Tests for Cavity Barriers Oct 2008032 Bending Test for swivel Joints made of PVC-U July 2009

033 Test method for discontinuously laid bituminous roof covering products – Determination of watertightness July 2009

034 General ER 3 Checklist for ETAGs/CUAPs/ETAs- Content and/or release of dangerous substances in products/kits July 2009

034 am. General ER 3 Checklist for ETAGs/CUPAs/ETAs-Content and/or release of dangerous substances in products/kits March 2012

035 Rules For Extended Application of Test Results of Fire Resisting Elements July 2009037 Test method for elastomeric insulating elements – Determination of creep May 2011038 Assessment procedure for durability of thin metallic composite panels August 2012

042 Plastic piping kits for heating systems, consisting of pipes made of PB-R and mechanical and/or welded fittings July 2012