Ethernet Switch

Ethernet SwitchUser Manual

Version 1.3-EN

About this document

This document has been generated from XSL (Extensible Stylesheet Language) source with RenderX XEP Formatter, version 3.7.1 Client Academic. For more information about XSL, visit the official World Wide Web Consortium XSL homepage: http://www.w3.org/Style/XSL For more information about RenderX and XEP, visit the RenderX site: http://www.renderx.com

Ethernet Switch: User Manual

Flying Pig Systems

by Nick Hunt and Richard Bunn

Copyright

© High End Systems, Inc. 2004, All Rights Reserved.

Changes

Information and specifications in this document are subject to change without notice. High End Systems, Inc.assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.

Trademarks

Trademarks used in this text: High End Systems, Wholehog II, and Wholehog III, are registered trademarks;the High End Systems globe logo and the Hog logo are trademarks of High End Systems, Inc. or High EndSystems Europe Ltd.

Other trademarks and trade names may be used in this document to refer to either the entities claiming themarks and names or their products. High End Systems disclaims any proprietary interest in trademarks andtrade names owned by others.

FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant topart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential environment. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation,in which case the user will be required to correct the interference at his own expense.

Optical Information

Complies with IEC 60825/CDRH Class 1, and 21 CFR1040 - Class 1 Laser Products when equipped with FlyingPig Systems 1000Base-SX (p/n 61040026) or 1000Base-LX (p/n 61040027) Gigabit Interface Converters.

Product Modification Warning

High End Systems products are designed and manufactured to meet the requirements of United States andInternational safety regulations. Modifications to the product could affect safety and render the product non-compliant to relevant safety standards.

Mise En Garde Contre La Modification Du Produit

Les produits High End Systems sont conçus et fabriqués conformément aux exigences des règlements interna-tionaux de sécurité. Toute modification du produit peut entraîner sa non conformité aux normes de sécuritéen vigueur.

Produktmodifikationswarnung

Design und Herstellung von High End Systems entsprechen den Anforderungen der U.S. Amerikanischenund internationalen Sicherheitsvorschriften. Abänderungen dieses Produktes können dessen Sicherheit beein-trächtigen und unter Umständen gegen die diesbezüglichen Sicherheitsnormen verstoßen.

Avvertenza Sulla Modifica Del Prodotto

I prodotti di High End Systems sono stati progettati e fabbricati per soddisfare i requisiti delle normative disicurezza statunitensi ed internazionali. Qualsiasi modifica al prodotto potrebbe pregiudicare la sicurezza erendere il prodotto non conforme agli standard di sicurezza pertinenti.

Flying Pig Systems2

Ethernet Switch

Advertencia De Modificación Del Producto

Los productos de High End Systems están diseñados y fabricados para cumplir los requisitos de las reglamenta-ciones de seguridad de los Estados Unidos e internacionales. Las modificaciones al producto podrían afectarla seguridad y dejar al producto fuera de conformidad con las normas de seguridad relevantes.

Important Safety Information

Instructions pertaining to continued protection against fire, electric shock, and injury to persons are found inSafety Information (8.1).

Please read all instructions prior to assembling, mounting, and operating this equipment.

Important: Informations De Sécurité

Les instructions se rapportant à la protection permanente contre les incendies, l'électrocution et aux blessurescorporelles se trouvent dans Section 8.2, « Importantes Informations Sur La Sécurité ».

Veuillez lire toutes les instructions avant d'assembler, de monter ou d'utiliser cet équipement.

Wichtige Sicherheitshinweise

Sicherheitsanleitungen zum Schutz gegen Feuer, elektrischen Schlag und Verletzung von Personen finden Siein Wichtige Hinweise Für Ihre Sicherheit (8.3).

Vor der Montage, dem Zusammenbau und der Intbetriebnahme dieses Geräts alle Anleitungen sorgfältigdurchlesen.

Informazioni Importanti Di Sicurezza

Le istruzioni sulla protezione da incendi, folgorazione e infortuni sono contenute nell Sezione 8.5, “ImportantiInformazioni Di Sicurezza”.

Si prega di leggere tutte le istruzioni prima di assemblare, montare e azionare l'apparecchiatura.

Informacion Importante De Seguridad

En el Sección 8.4, “Información Importante De Seguridad” se encuentran instrucciones sobre protección continuacontra incendios, descarga eléctrica y lesiones personales.

Lea, por favor, todas las instrucciones antes del ensamblaje, montaje y operación de este equipo.

Warranty Information

Limited Warranty: Unless otherwise stated, your product is covered by a one year parts and labour limitedwarranty. It is the owner's responsibility to furnish receipts or invoices for verification of purchase, date, anddealer or distributor. If purchase date cannot be provided, date of manufacture will be used to determinewarranty period.

Returning an Item Under Warranty for Repair: It is necessary to obtain a Return Material Authorization(RMA) number from your dealer or point of purchase BEFORE any units are returned for repair. The manu-facturer will make the final determination as to whether or not the unit is covered by warranty.

Any Product unit or parts returned to High End Systems must be packaged in a suitable manner to ensure theprotection of such Product unit or parts, and such package shall be clearly and prominently marked to indicatethat the package contains returned Product units or parts and with an RMA number. Accompany all returnedProduct units or parts with a written explanation of the alleged problem or malfunction. Ship returned Productunits or parts to: 53 Northfield Road, London, W13 9SY, UK.

Note: Freight Damage Claims are invalid for fixtures shipped in non-factory boxes and packing materials.

Freight: All shipping will be paid by the purchaser. Under no circumstances will freight collect shipmentsbe accepted.

3Flying Pig Systems

Ethernet Switch

REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDYOF THE CONSUMER. HIGH END SYSTEMS, INC. MAKES NO WARRANTIES, EXPRESS OR IMPLIED,WITH RESPECT TO ANY PRODUCT, AND HIGH END SPECIFICALLY DISCLAIMS ANY WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. HIGH END SHALL NOT BE LIABLEFOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS,SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTSOR THE PARTIAL OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION,WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE,AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.

Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs orparts. This warranty gives you specific legal rights, and you may also have other rights which vary from stateto state.

Flying Pig Systems4

Ethernet Switch

Declaration of ConformityAccording to ISO/IEC Guide 22 and EN45104

Flying Pig Systems (High End Systems Europe Ltd.)Manufacturer's name:

High End Systems Europe Ltd.Distributor's name:

53 Northfield Road, London, W13 9SYDistributor's address:

Declares that the product:

Wholehog IIIProduct Name:

AllProduct Number:

AllProduct Options:

Conforms to the following EEC directives:

73/23/EEC, as amended by 93/68/EEC

89/336/EEC, as amended by 92/31/EEC and 93/68/EEC

Equipment referred to in this declaration of conformity was first manufacturedin compliance with the following standards in 2002:

EN60950:2000Safety:

EN55103-1:1996 (E2)EMC:

EN55103-2:1996 (E2)

I, the undersigned, hereby declare that the equipment specified above conformsto the above Directives and Standards.

Richard Bunn, Compliance Engineer

30 May 2002

iFlying Pig Systems

Table of Contents1: Introduction ............................................................................... 7

1.1 Key .................................................................................. 82: Setting Up the Ethernet Switch ...................................................... 9

2.1 Power .............................................................................. 92.2 Working with Ethernet Switches .......................................... 9

2.2.1 Using the Front Panel Controls .................................. 92.2.2 Using with the Wholehog III Console ......................... 92.2.3 Control from a Web Browser .................................. 10

2.3 Network Settings .............................................................. 102.3.1 Checking and Setting the Net Number ................... 102.3.2 Checking and Setting the IP Address ...................... 102.3.3 Setting the Port Number ........................................ 11

3: Options and Defaults ................................................................. 133.1 Configuring the Webserver Interface ................................. 133.2 Locking the Controls ........................................................ 133.3 Backlight Off Time ........................................................... 143.4 Watchdog ...................................................................... 143.5 Resetting the Ethernet Switch ........................................... 14

4: Checking the Ethernet Switch's Status ......................................... 154.1 Viewing Status on the Front Panel Display .......................... 154.2 Front and Rear Panel Status Indicators ............................... 15

4.2.1 General Status Indicators (front panel) .................... 154.2.2 Status Indicators for the Fibre Optic Ports (frontpanel) ......................................................................... 164.2.3 Status Indicators for Ports 1-4 (front panel) ............... 164.2.4 Status Indicators for Ports 5-16 (rear panel) .............. 164.2.5 Status Indicators for Ports 17-18 (rear panel) ............. 16

5: Updating Software ..................................................................... 176: Related Products ....................................................................... 19

6.1 Fibre Optic Connection Modules ...................................... 196.1.1 1000Base-SX GBIC Module ..................................... 196.1.2 1000Base-LX GBIC Module ..................................... 196.1.3 Installation and Removal ....................................... 19

6.2 Auxilliary Panel ................................................................ 196.2.1 Installation ............................................................ 20

7: Technical Specifications ............................................................ 217.1 Ethernet Switch ............................................................... 21

7.1.1 Input and Output Connections .............................. 217.1.2 Power, Weight and Dimensions .............................. 21

7.2 1000Base-SX GBIC Module ............................................... 217.3 1000Base-LX GBIC Module ................................................ 217.4 Ethernet Switch Auxilliary Panel ......................................... 22

7.4.1 Input and Output Connections .............................. 227.4.2 Power, Weight and Dimensions .............................. 22

8: Safety Information ..................................................................... 238.1 Safety Information ........................................................... 23

8.1.1 Warning: For Continued Protection AgainstFire .............................................................................. 238.1.2 Warning: For Continued Protection Against ElectricShock .......................................................................... 23

8.2 Importantes Informations Sur La Sécurité ............................ 24

iiiFlying Pig Systems

8.2.1 Mise En Garde: Pour Une Protection PermanenteContre Les Incendies .................................................... 248.2.2 Mise En Garde: Pour Une Protection PermanenteContre Les Chocs Électriques ........................................ 24

8.3 Wichtige Hinweise Für Ihre Sicherheit ................................. 248.3.1 Warnung: Zum Schutz Vor Brandgefahr ................... 248.3.2 Warnung: Zum Schutz Gegen Gefährliche Körper-ströme ......................................................................... 24

8.4 Información Importante De Seguridad .............................. 258.4.1 Advertencia: Para Protección Continua Contra In-cendios ....................................................................... 258.4.2 Advertencia: Para La Protección Continua ContraElectrocuciones ........................................................... 25

8.5 Importanti Informazioni Di Sicurezza ................................... 268.5.1 Avvertenza: Per Prevenire Incendi .......................... 268.5.2 Avvertenza: Per Prevenire Le Scosse Elettriche ......... 26

8.6 Vigtig Sikkerhedsinformation ............................................. 26Glossary ...................................................................................... 27Index .......................................................................................... 31

Flying Pig Systemsiv

Ethernet Switch

List of Figures1.1 A Typical Network with Two Consoles .......................................... 74.1 Screen displaying ports overview .............................................. 154.2 Screen displaying port status .................................................... 15

vFlying Pig Systems

Section 1: Introduction

Ethernet networks have become commonplace as a means of connecting lightingand other entertainment equipment together across theatres, theme parks, stadi-ums, retail and architectural spaces. Conventional Ethernet switches designedfor office environments have failed to address the needs of these systems. TheFlying Pig Systems Ethernet Switch offers advanced features in a rugged andeasy to use package for the entertainment environment.

The Ethernet Switch has a mix of connectors back and front for easy connectivity.Normal RJ45s are provided at the back for internal connections within a rack.Rugged Ethercon sockets on the front offer a robust connection for portableequipment or system testing. Gigabit connections are supported for largebandwidth backbones.

Ethernet connections over standard copper cable are limited to 100 metres. Toallow for longer distances, the Ethernet Switch has two slots for fibre modules.These support fibre optic links at Gigabit speed up to 10km using appropriatefibre. An auxilliary 1U face-panel is available with rugged Lemo fibre connectors;see Auxilliary Panel (6.2). These fibre connectors make the link robust enoughfor the toughest touring environments.

A typical lighting network is shown in Figure 1.1, “A Typical Network with TwoConsoles”.

Ethernet switch

Wholehog III console

Wholehog III console

DMX Processor

4 DMX universes

DMX Processor

4 DMX universes

Figure 1.1. A Typical Network with Two Consoles

The Ethernet Switch incorporates a management processor and display, allowingyou to monitor and manage network traffic both from the front panel of theswitch itself or remotely using either a Wholehog III console or web browser.

You can connect network devices to any of the Ethernet Switch's ports. Ports 1to 16 support 10 and 100 Mbps links. Ports 17 and 18 also support 1 Gbps links.When an RJ45 or Ethercon is connected to the switch, the switch will automatic-

7Flying Pig Systems

ally configure the link to support the maximum speed and duplex mode (half-or full-duplex) of the attached device. The switch will also sense whether thecable is straight-through or crossover and automatically configure the connectionaccordingly.

You can use Fibre optic links by fitting a GBIC module (purchased separately)into one of the slots at the rear of the switch; see Fibre Optic Connection Modules(6.1).

1.1 Key

The following conventions are used in the text of the manual:

A cross reference to another part of the manual. In electronicversions of the manual (HTML and PDF) these references areclickable hyperlinks.

Setting Up the EthernetSwitch (2)

A reference to a term in the Glossary. In electronic versions ofthe manual (HTML and PDF) these references are clickablehyperlinks.

console

A name of an interface element such as a button.Setup

A series of operations that navigate through menus and screens.Setup → Network

You will also find important or useful information highlighted:

! Caution

A caution, which has information about hazards to equipment orpersonnel.» Important

An important note, usually alerting you to situations where you mightlose some of your show's data. There are very few of these.

Tip

A tip, to help you be more productive when using the EthernetSwitch.

Flying Pig Systems8

Section 1: Introduction

Section 2: Setting Up the Ethernet Switch

2.1 Power

You can connect the Ethernet Switch to a mains supply of between 100 and 240VAC.

2.2 Working with Ethernet Switches

You can control the Ethernet Switch's functions from the front panel controls,from a Wholehog III console, or from a web browser. Using a console or a webbrowser are described below; the remainder of this manual assumes that youare using the switch's front panel controls.

2.2.1 Using the Front Panel Controls

Menus allow you to navigate to the various screens and functions:

Move the cursor through the options backwards.

Select the option currently highlighted by the cursor.

Move the cursor through the options forwards.

The menus use the following conventions:

Confirm changes and return to the previous screen.OK

Abandon changes and return to the previous screen.Cancel

Return to the previous screen.Close

To set a numerical value:

1. Move the cursor to the value you want to change.

2. Press the key, and the first digit of the number will behighlighted.

3. Use the key to change the value, and the and keysto select a different digit of the number.

4. When you have finished, press until no digits are selected.You can then use and to select options in the usual way.

2.2.2 Using with the Wholehog III Console

You can monitor the Ethernet Switch using the Wholehog III console in the sameway as other network processors such as DMX Processors and MIDI/Timecode

9Flying Pig Systems

Processors. To be ‘visible’ to the console on the network, the Ethernet Switchshould be set to have the same port number as the console; see Setting the PortNumber (2.3.3). It is not currently possible to perform full configuration of theEthernet Switch settings from the console.

2.2.3 Control from a Web Browser

You can configure the Ethernet Switch from a web browser using a personalcomputer connected to the network:

1. Check that the Ethernet Switch's webserver is enabled; seeConfiguring the Webserver Interface (3.1).

2. Connect your computer to the network and start the webbrowser.

3. Determine the IP address of your switch: see Checking and Settingthe IP Address (2.3.2).

4. Point your browser at this IP address, for example:

http://172.31.0.20/.

5. You can view and change Network status and settings fromthe web browser.

2.3 Network Settings

2.3.1 Checking and Setting the Net Number

The Net Number is the number used to identify the Ethernet Switch for remoteconfiguration. It is displayed on the main screen of the switch in the top righthand corner. To set the Net Number:

1. Main → Network Configuration : navigate to the Network Con-figuration screen.

2. Set the Net Number to any value between 00 and 99.

3. OK : return to the Main screen.

2.3.2 Checking and Setting the IP Address

In addition to the Net Number used by consoles to identify the Ethernet Switch,each network device needs to have an IP address and Subnet Mask set, so thatother devices and personal computers can identify them. The easiest way to dothis is to use DHCP, which is a system that allows network devices to setthemselves up automatically. One device on the network (for example aWholehog III console) acts a DHCP server, and other devices are assigned anIP address by the server.

Flying Pig Systems10


There are times when it is desirable to set a fixed or 'static' IP address. This willbe the case when there is no DHCP server, or the network is shared with unre-lated equipment. If you intend to monitor your switch using a web browser, astatic IP address may also be useful. You should contact your system adminis-trator to determine the optimum settings for your network.

To set a static IP address:

1. Main → Network Configuration → IP Status → IP Config : navigateto the IP Config screen.

2. Set DHCP Off.

3. Set the IP Address and Subnet Mask as required.

4. OK : return to the IP Status screen.

5. OK : return to the Network Configuration screen.


7. Main → Control Panel : navigate to the Control Panel.

8. Hard Reset : the DMX Processor needs a hard reset for changesto take effect.

2.3.3 Setting the Port Number

The Port Number identifies a channel which the Ethernet Switch's managementprocessor uses to communicate and should be set to the same value as for otherequipment on the Network.

To set the Port Number:

1. Main → Network Configuration : navigate to the Network Con-figuration screen.

2. Set the Port Number as required.


The default port number for the Wholehog III family of equipment islt is 6600.

11Flying Pig Systems


Section 3: Options and Defaults

The Ethernet Switch has various options and controls, set in the Control Panelscreen:

• Main → Control Panel

You can revert all settings to their default values by selecting Set to Defaults.

3.1 Configuring the Webserver Interface

You can control the Ethernet Switch remotely from a web browser. To enablethe webserver:

1. Main → Ports → Global → Webserver

2. Check the box to enable the webserver.

3. Set the port number (0-65535). By default this is 80 allowingbrowsers direct access.

4. OK : return to main menu.

Tip

When the webserver is enabled, Ethernet Switch settings can beaccessed from anywhere on the network. For show security, youmay wish to disable the webserver once you have finished configur-ing the Ethernet Switch.

3.2 Locking the Controls

You can use the Lock function to lock the Ethernet Switch's controls:

1. In the Control Panel, select Lock.

2. Enter your chosen 4-digit code number, and select OK to con-firm. The DMX Processor is now locked.

To unlock, enter the correct four digit code.» Important

Make sure that you keep a record of your lock code. The EthernetSwitch cannot be unlocked without it.


3.3 Backlight Off Time

Selecting Backlight in the Control Panel opens a screen where you can set thedelay time before the backlight goes off. The Permanent setting keeps the lighton continually.

3.4 Watchdog

The Watchdog feature automatically restarts the Ethernet Switch if its softwarestops running for some reason. Watchdog is on by default, and generally it isbest to leave it switched on. However, if you suspect that an Ethernet Switch isnot working correctly, you may want to turn Watchdog off so that you can seeany error messages before restarting it:

1. In the Control Panel, select Watchdog.

2. Deselect the Watchdog checkbox, and select OK.

3.5 Resetting the Ethernet Switch

There are two types of reset: soft and hard. Soft Reset resets the Ethernet Switchso that it re-initialises communication with the network. Hard Reset is equivalentto turning off and on the mains power. You can do both types of reset from theControl Panel.


Section 3: Options and Defaults

Section 4: Checking the Ethernet Switch's Status

4.1 Viewing Status on the Front Panel Display

You can view the link status and connection speed of all the ports on the frontpanel display by navigating to the Ports screen:

• Main → Ports : navigate to the main ports screen.

This displays all the available ports on a single screen; see Figure 4.1, “Screendisplaying ports overview”. The connection speed is shown below each port forall active links.

Figure 4.1. Screen displaying ports overview

You can view detailed information about an individual port by selecting thatport. This displays the port name, the port type and information about connectedequipment; see Figure 4.2, “Screen displaying port status”.

Figure 4.2. Screen displaying port status

Tip

You can change the port name using the web browser interface;see Control from a Web Browser (2.2.3).

4.2 Front and Rear Panel Status Indicators

The lights on the front and rear panels show the Ethernet Switch's status.

4.2.1 General Status Indicators (front panel)

Status When OnColourLabel

Management processor power OKRed3.3V

Switch controller power OKRed1.2V



Network traffic is passing through the switch (the totalload is greater than 0.05% of its capacity)

RedTraffic

The switch is operating (off while the switch is initialising)RedActive

the switch is connected to a Wholehog III show serverRedServer

4.2.2 Status Indicators for the Fibre Optic Ports (front panel)


A 1000Base-SX Fibre module is fitted in the GBIC slotRed1000SX

A 1000Base-LX Fibre module is fitted in the GBIC slotRed1000LX

Network traffic is passing through the portRedData

A link has been establishedRedLink

4.2.3 Status Indicators for Ports 1-4 (front panel)


A 100Mbps connection has been established. Otherwise,the link is only 10Mbps, because the link partner doesnot support fast ethernet. A fast ethernet link is recom-mended.

Red100

The port is operating in full-duplex modeRedFull

Network traffic is passing through the portRedData

A link has been establishedRedLink

4.2.4 Status Indicators for Ports 5-16 (rear panel)

Status When OnColour

Network traffic is passing through the portGreen

A link has been establishedOrange

4.2.5 Status Indicators for Ports 17-18 (rear panel)


Network traffic is passing through the portGreenData

A link has been establishedGreenLink


Section 4: Checking the Ethernet Switch's Status

Section 5: Updating Software

The Ethernet Switch contains software that may require updating. If the switchis being used with a Wholehog III console, you can update the software fromthe console; see the Wholehog III User Manual for details.

Alternatively, the switch software may be updated using a personal computerrunning Windows software:

1. Download the Ethernet Switch software from the Flying PigSystems website (www.flyingpig.com[http://www.flyingpig.com]) and install it on the computer.

2. Connect the computer to any port on the switch using an Eth-ernet cable.

3. Follow the instructions supplied with the software to configurethis computer as a reload server.

To force the Ethernet switch to update its software from the computer:

1. Turn off the mains power to the Ethernet Switch

2. Turn the switch back on, while holding the key

3. The switch will download its software from the PC


http://www.flyingpig.com

Section 6: Related Products

You can customise the Ethernet Switch for your installation or application usingthe following accessories.

6.1 Fibre Optic Connection Modules

Two types of fibre optic modules are available to allow you to connect the Eth-ernet Switch to a high-speed fibre link.

6.1.1 1000Base-SX GBIC Module

The 1000Base-SX GBIC Module provides a 1000Base-SX, full duplex fibre opticconnection that you can use to connect switches at distances up to 500m usingsuitable multimode fibre.

6.1.2 1000Base-LX GBIC Module

The 1000Base-LX GBIC Module provides a 1000Base-LX, full duplex fibre opticconnection that you can use to connect switches at distances up to 550m usingsuitable multimode fibre or up to 10 km using single mode fibre.

6.1.3 Installation and Removal

Insert the module into one of the two GBIC slots on the rear of the switch. A railwill guide the module into the connector. Push the module firmly to obtain agood connection. The GBIC module will latch into the chassis.

Once fitted, the switch will recognise the module and indicate link status on itsfront panel.

To remove the GBIC Module, squeeze the tabs on the module together and pullit out of the slot.

6.2 Auxilliary Panel

The Auxilliary panel is a 1U panel which may be mounted in a rack adjacent tothe switch and is particularly useful for touring applications. The Panel is fittedwith four Ethercon connectors and two rugged Lemo fibre optic connectors.


6.2.1 Installation

The Auxilliary panel is supplied with four Cat 5e patch cables. Connect thesebetween the Auxilliary panel and ports 5 to 8 on the rear of the switch, or anyother free 10/100Base-T/TX ports.

The two fibre optic flying leads from the Lemo connectors should be connectedto GBIC modules installed in ports Fibre1 and Fibre2 at the rear of the switch.


Section 6: Related Products

Section 7: Technical Specifications

7.1 Ethernet Switch

7.1.1 Input and Output Connections

IEC 320 connector (5A/250V rated cable supplied)100-240V, 50/60Hz, 0.5A maximum1 x 5x20mm 2A T fuses

Mains in:

4 x 10/100base-TX Ethernet Ports with Auto-MDIX sup-port: Neutrik Ethercon (RJ45 compatible) on front panel12 x 10/100base-TX Ethernet Ports with Auto-MDIX sup-port: RJ45 on back2 x 10/100/1000base-T/TX Ethernet Ports with Auto-MDIXsupport: RJ45 on back2 x GBIC (Gigabit Interface Converter) slot on back

Ethernet:

7.1.2 Power, Weight and Dimensions

30WPower:

1.7KgWeight:

Dimensions: 480 (w) x 169 (d) x 45mm (h), 1U, 19 inchrack compatible

Dimensions:

7.2 1000Base-SX GBIC Module

Full Duplex SC 1000Base-SX when fitted in GBICslot

Input and Output connections

500m with 50/125um MMF220m with 62.5/125um MMF

Performance Specification

7.3 1000Base-LX GBIC Module

Full Duplex SC 1000Base-LX when fitted in GBICslot

Input and Output connections

550m with 50/125um MMF550m with 62.5/125um MMF10km with 9/125um SMF

Performance Specification


7.4 Ethernet Switch Auxilliary Panel

7.4.1 Input and Output Connections

4 x Neutric Ethercon panel mounted with Cat 5e patchcables terminated with RJ45 connectors to connect torear of Ethernet Switch2 x Lemo EGG.3K.03A.CLZ Full duplex fibre optic con-nectors panel mounted with 62.5/125um multimodefibre terminated with SC connectors to connect to GBICmodules in rear of Ethernet Switch

Ethernet:

7.4.2 Power, Weight and Dimensions

0.6KgWeight:

Dimensions: 480 (w) x 120 (d) x 45mm (h), 1U, 19 inchrack compatible

Dimensions:


Section 7: Technical Specifications

Section 8: Safety Information

8.1 Safety Information

8.1.1 Warning: For Continued Protection Against Fire

• This equipment for connection to branch circuit having a max-imum overload protection of 20 A.

8.1.2 Warning: For Continued Protection Against Electric Shock

1. If this equipment was received without a line cord plug, attachthe appropriate line cord plug according to the following code:

• brown - live

• blue - neutral

• green/yellow - earth

2. As the colours of the cores in the mains lead of this equipmentmay not correspond with the coloured markings identifyingthe terminals in your plug, proceed as follows:

• the core which is coloured green and yellowmust be connected to the terminal in the plugwhich is marked with the letter E or by the earth

symbol , or coloured green or green andyellow.

• the core which is coloured blue must be connec-ted to the terminal which is marked with theletter N or coloured black.

• the core which is coloured brown must be con-nected to the terminal which is marked withthe letter L or coloured red.

3. Class I equipment. This equipment must be earthed.

4. Equipment suitable for dry locations only. Do not expose thisequipment to rain or moisture.

5. Disconnect power before servicing.

6. Refer servicing to qualified personnel; no user serviceable partsinside.


8.2 Importantes Informations Sur La Sécurité

8.2.1 Mise En Garde: Pour Une Protection Permanente Contre LesIncendies

• Pour Une Protection Permanente Contre Les Incendies Cet ap-pareil de connection au circuit comporte une protection contreles surcharges de 20 A.

8.2.2 Mise En Garde: Pour Une Protection Permanente Contre LesChocs Électriques

1. Si cet équipement est livré sans prise de cable, veuillez connecterla prise de cable correcte selon le code suivant:

• marron - phase

• bleu - neutre

• vert/jaune - terre

2. Débrancher le courant avant d'effectuer des réparations.

3. Cet équipement doit être uniquement utilisé dans des endroitssecs. Ne pas l'exposer à la pluie ou l'humidité.

4. À l'intérieur de l'équipement il n'y a pas de pièces remplaçablespar l'utilisateur. Confiez l'entretien à un personnel qualifié.

5. Equipement de Classe I. Cet équipement doit être mis à la terre.

8.3 Wichtige Hinweise Für Ihre Sicherheit

8.3.1 Warnung: Zum Schutz Vor Brandgefahr

• Dieses Gerät darf nur an eine Zweigleitung mit einem Überlas-tungsschutz von höchstens 20 A angeschlossen werden.

8.3.2 Warnung: Zum Schutz Gegen Gefährliche Körperströme

1. Wenn dieses Gerät ohne einen Netzkabelstecker erhalten wurde,ist der entsprechende Netzkabelstecker entsprechend dem fol-genden Code anzubringen:

• Braun - Unter Spannung stehend



• Blau - Neutral

• Grün/Gelb - Erde

2. Vor Wartungsarbeiten stets den Netzstecker ziehen.

3. Diese Geräte sind nur zum Einbau in trockenen Lagen bestimmtund müssen vor Regen und Feuchtigkeit geschützt werden.

4. Servicearbeiten sollten nur von Fachpersonal ausgeführt wer-den. Das Gerät enthält keine wartungsbedürftigen Teile.

5. Dieses Gerät gehört zur Klasse I. Dieses Gerät muß geerdetwerden.

8.4 Información Importante De Seguridad

8.4.1 Advertencia: Para Protección Continua Contra Incendios

• Este equipo debe conectarse a un circuito que tenga una protec-ción máxima contra las sobrecargas de 20 A.

8.4.2 Advertencia: Para La Protección Continua Contra Electrocu-ciones

1. Si se recibió este equipo sin el enchufe de alimentacion, monteusted el enchufe correcto según el clave siguente:

• moreno - vivo

• azul - neutral

• verde/amarillo - tierra

2. Desconecte el suministro de energía antes de prestar serviciode reparación.

3. Este equipo se adecua a lugares secos solamente. no lo expongaa la lluvia o humedad.

4. Derive el servicio de reparación de este equipo al personal cal-ificado. El interior no contiene repuestos que puedan ser repara-dos por el usuario.

5. Equipo de Clase I. Este equipo debe conectarse a la tierra.



8.5 Importanti Informazioni Di Sicurezza

8.5.1 Avvertenza: Per Prevenire Incendi

• Questa apparecchiatura e' da collegarsi ad un circuito con unaprotezzione da sovraccarico massima di 20 amperes.

8.5.2 Avvertenza: Per Prevenire Le Scosse Elettriche

1. Se questa apparecchiatura è stata consegnata senza una spinadel cavo di alimentazione, collegare la spina appropriata delcavo di alimentazione in base ai seguenti codici:

• marrone - sotto tensione

• blu - neutro

• verde/giallo - terra

2. Disinnestare la corrente prima di eseguire qualsiasi riparazione.

3. Questa apparecchiatura e' da usarsi in ambienti secchi. Non e'da essere esposta ne alla pioggia ne all' umidita'.

4. Per qualsiasi riparazione rivolgersi al personale specializzato.L' utente non deve riparare nessuna parte dentro l' unita'.

5. Aparecchio di Classe I. Questa apparecchiatura deve esseremessa a terra.

8.6 Vigtig Sikkerhedsinformation

Advarsel: Beskyttelse mod elektrisk chock.

VIGTIGT! LEDEREN MED GUL/GROEN ISOLATION MAA KUN TILSLUTTES

KLEMME MAERKET ELLER .



Glossary

1

10 Base-T An older flavour of Ethernet, that is slower(10 MBits per second) than the 100 Base-Tused by Wholehog III components. If con-nected to other equipment that only sup-ports this flavour, then Wholehog III com-ponents will automatically detect this, andrun their Ethernet connections at this slowerspeed. However this is not the recommen-ded way to set up your network.See Also 100 Base-T.

100 Base-T A flavour of Ethernet, that supports datarates of up to 100 MBits per second. AllWholehog III components support this fla-vour of Ethernet, and comply with all relev-ant standards, so networking equipmentdesigned for 100Base-T should be compat-ible with the Wholehog III.See Also 10 Base-T.

C

console The user interface of a lighting control sys-tem. The Wholehog III console is one com-ponent of a network that may include otherWholehog III desks, expansion wings, ex-ternal devices, offline editors and visual-isers, along with dimmers and fixtures.

cross-over cable When you connect two Wholehog III com-ponents (or computers) together directly,you need to use a special type of Ethernetcable called a cross-over cable. This is differ-ent from the normal type of Ethernet cableused with hubs and switches (see below).We supply a cross-over cable with eachconsole and DMX Processor.See Also Ethernet.

D

default The value for a setting that the EthernetSwitch uses if you don't give it a value.

desk See console.

DHCP Dynamic Host Configuration Protocol is away for a computer to ask a master com-puter on a network to assign it an IP ad-


dress when it connects. Many existing net-works are configured this way, and theWholehog III supports this system. Youshould talk to the administrator of the net-work you want to connect to to find outmore.See Also Ethernet, IP address.

E

Ethernet A defined way of connecting computerequipment together. It comes in a varietyof flavours.See Also 10 Base-T, 100 Base-T, IP address,hub.

F

FAQ Short for Frequently Asked Questions.

H

hub See switch.

I

IP address On an Ethernet network, each WholehogIII component has an address, called an IPaddress, used to identify it. You can usuallyuse the default addresses, but if you areconnecting to an existing network you mayneed to specify a different address, accord-ing to how your network is configured.See Also Ethernet.

M

multicast A network protocol or language that com-puters use to talk to each other over Ether-net. The Wholehog III uses this standardprotocol, which means that it can safely beconnected to other networks of computersand will not interfere with them. For show-critical situations we recommend runningthe Wholehog III on its own independentnetwork.See Also Ethernet.

N

network processor A network device such as a DMX Processoror MIDI/Timecode Processor that handles


Glossary

data coming into or going out of theWholehog III network.

node Network nodes are items of equipmentconnected to the network. Consoles, DMXProcessors and PCs are all nodes.See Also console.

P

port number On a computer network, the port numberdefines a particular type of network traffic.In the case of a Wholehog III network, eachshow running on the network has its ownport number, so that a console can identifyand connect to a particular show.

S

server See show server.

show server The Wholehog III that ‘owns’ a show. Otherconsoles may join the show, but the originalconsole that created the show will remainthe show server.

subnet mask A local mask that specifies which parts ofthe IP address specify the subnetwork, andwhich parts identify the host. For example,an IP Address of 172.31.1.20 with a subnetmask of 255.255.0.0 specifies host 1.20 onsubnet 172.31.0.0.See Also IP address.

switch When you want to connect more than twoWholehog III components (or computers)together, then you need a special piece ofequipment to allow them to interconnectcalled an ethernet switch.See Also Ethernet.

T

TCP/IP A network protocol or language that com-puters use to talk to each other over Ether-net. The Wholehog III uses this standardprotocol, which means that it can safely beconnected to other networks of computersand will not interfere with them. For show-critical situations we recommend runningthe Wholehog III on its own independentnetwork.See Also Ethernet.


Glossary

U

UDP A network protocol or language that com-puters use to talk to each other over Ether-net. The Wholehog III uses this standardprotocol, which means that it can safely beconnected to other networks of computersand will not interfere with them. For show-critical situations we recommend runningthe Wholehog III on its own independentnetwork.See Also Ethernet.


Glossary

Aauto sensing

ethernet, 7auxilliary panel, 19

installation, 20technical specification, 22

Bbacklight off time, 14browser

controlling the Ethernet Switch from, 10buttons

on the front panel, 9

Ccomputer

controlling the Ethernet Switch from, 10console, Wholehog III, 7controls

locking, 13on the front panel, 9

crossoverethernet cable, 7

Ddefault settings, 13DHCP, 10

Ffibre optic ports, 19

installation, 19removal, 19status indicators, 16technical specification, 21

GGBIC, 19

technical specification, 21glossary, 8, 27

Hhard reset, 14help

key to this manual, 8

Iindicators, 15IP address

checking and setting, 10

Kkey, 8

LLEDs, 15lights

status indicators, 15locking the controls, 13

Mmains power, 9

Nnet number

checking and setting, 10network, 7

Ooptions, 13

Pport number

checking and setting, 11ports, 7

status, 15power, 9

Rresetting, 14

Ssafety information, 23soft reset, 14software

updating, 17specifications, 21static IP address, 10status of the Ethernet Switch, 15subnet mask, 10symbols, 8

Ttechnical specifications, 21

Uupdating software, 17


Wwatchdog, 14web browser

controlling the Ethernet Switch from, 10webserver, 13Wholehog III console, 7

as a DHCP server, 10using the Ethernet Switch with, 9


Index

Ethernet Switch

Documents

Transcript of Ethernet Switch