Installing the Ethernet Routing Switch 1600 Series Switch ...

Part No. 316860-DJune 2006

4655 Great America ParkwaySanta Clara, CA 95054

*316860-D*

Installing the Ethernet Routing Switch 1600 Series SwitchSoftware Release 2.1

2

316860-D

Copyright © Nortel Networks Limited 2005-2006. All rights reserved.

The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks NA Inc.

The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of that license. The software license agreement is included in this document.

Trademarks

Nortel, Nortel Networks, the Nortel logo and the Globemark are trademarks of Nortel Networks.

Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation.

Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated.

Java is a trademark of Sun Microsystems, Inc.

The asterisk after a name denotes a trademarked item.

Restricted rights legend

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013.

Notwithstanding any other license agreement that may pertain to, or accompany the delivery of, this computer software, the rights of the United States Government regarding its use, reproduction, and disclosure are as set forth in the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19.

Statement of conditions

In the interest of improving internal design, operational function, and/or reliability, Nortel Networks Inc. reserves the right to make changes to the products described in this document without notice.

Nortel Networks Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Portions of the code in this software product may be Copyright © 1988, Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms of such portions are permitted, provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that such portions of the software were developed by the University of California, Berkeley. The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission.

SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

In addition, the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure (that may incorporate by reference certain limitations and notices imposed by third parties).

3

Installing the Ethernet Routing Switch 1600 Series Switch

International regulatory statements of conformity

This is to certify that the Nortel Ethernet Routing Switch 1600 Series were evaluated to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards:

• EMC - Electromagnetic Emissions – CISPR 22, Class A• EMC - Electromagnetic Immunity – CISPR 24• Electrical Safety – IEC 60950, with CB member national deviations

Further, the equipment has been certified as compliant with the national standards as detailed below.

National electromagnetic compliance (EMC) statements of compliance

FCC statement (USA only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

ICES statement (Canada only)

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (Nortel Ethernet Routing Switch 1600 Series) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (Nortel Ethernet Routing Switch 1600 Series) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.

CE marking statement (Europe only)

EN 55 022 statements

This is to certify that the Nortel Ethernet Routing Switch 1600 Series are shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55 022 Class A (CISPR 22).

Caution: This device is a Class A product. In a domestic environment, this device can cause radio interference, in which case the user may be required to take appropriate measures.(For translations of this statement, see page 51.)

4

316860-D

EN 55 024 statement

This is to certify that the Nortel Ethernet Routing Switch 1600 Series are shielded against the susceptibility to radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55 024 (CISPR 24).

CE Declaration of Conformity

This product conforms to the provisions of the R&TTE Directive 1999/5/EC.

VCCI statement (Japan/Nippon only)

This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

BSMI statement for Nortel Ethernet Routing Switch 1600 Series (Taiwan only)

This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS 13438, Class A.

MIC notice for Nortel Ethernet Routing Switch 1600 Series (Republic of Korea only)

This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC). This device may not be sold for use in a non-business application.

Observe the Regulatory Marking label on the bottom surface of the chassis for specific certification information pertaining to this model. Each model in the Ethernet Switch Series which is approved for shipment to/usage in Korea is labeled as such, with all appropriate text and the appropriate MIC reference number.

5


National safety statements of compliance

CE marking statement (Europe only)

EN 60 950 statement

This is to certify that the Nortel Ethernet Routing Switch 1600 Series are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance.

NOM statement Ethernet Switches Nortel Ethernet Routing Switch 1600 Series (Mexico only)

The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial Méxicana (NOM):

Exporter: Nortel Networks, Inc.4655 Great America ParkwaySanta Clara CA 95054 USA

Importer: Nortel Networks de México, S.A. de C.V.Avenida Insurgentes Sur #1605Piso 30, OficinaCol. San Jose InsurgentesDeleg-Benito JuarezMéxico D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Input: (1648T Chassis)

100 to 240 VAC, 47 to 63 Hz, 4A at 115 VAC, 2A at 230 VAC maximumtwo power supplies

Información NOM (unicamente para México)

La información siguiente se proporciona en el dispositivo o en los dispositivos descritos en este documento, en cumplimiento con los requisitos de la Norma Oficial Méxicana (NOM):

Exportador: Nortel Networks, Inc.4655 Great America ParkwaySanta Clara, CA 95054 USA

Importador: Nortel Networks de México, S.A. de C.V.Avenida Insurgentes Sur #1605Piso 30, OficinaCol. San Jose InsurgentesDeleg-Benito JuarezMéxico D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Embarcar a: (1648T Chassis)

100 to 240 VAC, 47 to 63 Hz, 4A at 115 VAC, 2A at 230 VAC maximumdos fuente

6

316860-D

Denan statement (Japan/Nippon only)

7


Nortel Networks Inc. software license agreement

This Software License Agreement (“License Agreement”) is between you, the end-user (“Customer”) and Nortel Networks Corporation and its subsidiaries and affiliates (“Nortel Networks”). PLEASE READ THE FOLLOWING CAREFULLY. YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND/OR USE THE SOFTWARE. USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT. If you do not accept these terms and conditions, return the Software, unused and in the original shipping container, within 30 days of purchase to obtain a credit for the full purchase price.

“Software” is owned or licensed by Nortel Networks, its parent or one of its subsidiaries or affiliates, and is copyrighted and licensed, not sold. Software consists of machine-readable instructions, its components, data, audio-visual content (such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies. Nortel Networks grants you a license to use the Software only in the country where you acquired the Software. You obtain no rights other than those granted to you under this License Agreement. You are responsible for the selection of the Software and for the installation of, use of, and results obtained from the Software.

1. Licensed Use of Software. Nortel Networks grants Customer a nonexclusive license to use a copy of the Software on only one machine at any one time or to the extent of the activation or authorized usage level, whichever is applicable. To the extent Software is furnished for use with designated hardware or Customer furnished equipment (“CFE”), Customer is granted a nonexclusive license to use Software only on such hardware or CFE, as applicable. Software contains trade secrets and Customer agrees to treat Software as confidential information using the same care and discretion Customer uses with its own similar information that it does not wish to disclose, publish or disseminate. Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement. Customer shall not a) use, copy, modify, transfer or distribute the Software except as expressly authorized; b) reverse assemble, reverse compile, reverse engineer or otherwise translate the Software; c) create derivative works or modifications unless expressly authorized; or d) sublicense, rent or lease the Software. Licensors of intellectual property to Nortel Networks are beneficiaries of this provision. Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel Networks or certify its destruction. Nortel Networks may audit by remote polling or other reasonable means to determine Customer’s Software activation or usage levels. If suppliers of third party software included in Software require Nortel Networks to include additional or different terms, Customer agrees to abide by such terms provided by Nortel Networks with respect to such third party software.

2. Warranty. Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer, Software is provided “AS IS” without any warranties (conditions) of any kind. NORTEL NETWORKS DISCLAIMS ALL WARRANTIES (CONDITIONS) FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABLITITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON-INFRINGEMENT. Nortel Networks is not obligated to provide support of any kind for the Software. Some jurisdictions do not allow exclusion of implied warranties, and, in such event, the above exclusions may not apply.

3. Limitation of Remedies. IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANY OF THE FOLLOWING: a) DAMAGES BASED ON ANY THIRD PARTY CLAIM; b) LOSS OF, OR DAMAGE TO, CUSTOMER’S RECORDS, FILES OR DATA; OR c) DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), WHETHER IN CONTRACT, TORT OR OTHERWISE (INCLUDING NEGLIGENCE) ARISING OUT OF YOUR USE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS, ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIR POSSIBILITY. The forgoing limitations of remedies also apply to any developer and/or supplier of the Software. Such developer and/or supplier is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions and, in such event, they may not apply.

4. General

a. If Customer is the United States Government, the following paragraph shall apply: All Nortel Networks Software available under this License Agreement is commercial computer software and commercial computer software documentation and, in the event Software is licensed for or on behalf of the United States Government,

8

316860-D

the respective rights to the software and software documentation are governed by Nortel Networks standard commercial license in accordance with U.S. Federal Regulations at 48 C.F.R. Sections 12.212 (for non-Odd entities) and 48 C.F.R. 227.7202 (for Odd entities).

b. Customer may terminate the license at any time. Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license. In either event, upon termination, Customer must either return the Software to Nortel Networks or certify its destruction.

c. Customer is responsible for payment of any taxes, including personal property taxes, resulting from Customer’s use of the Software. Customer agrees to comply with all applicable laws including all applicable export and import laws and regulations.

d. Neither party may bring an action, regardless of form, more than two years after the cause of the action arose.

e. The terms and conditions of this License Agreement form the complete and exclusive agreement between Customer and Nortel Networks.

f. This License Agreement is governed by the laws of the country in which Customer acquires the Software. If the Software is acquired in the United States, then this License Agreement is governed by the laws of the state of New York.

9


Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Technical Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

How to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chapter 1: Introducing the 1600 Series Switch. . . . . . . . . . . . . . . . . . . . . . 21Ethernet Routing Switch 1600 Series models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Ethernet Routing Switch 1648T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Ethernet Routing Switch 1624G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ethernet Routing Switch 1612G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Chapter 2: Unpacking and Setting up the Switch . . . . . . . . . . . . . . . . . . . . 27Unpacking the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installing the Switch on a Desktop or Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Installing the Switch in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Powering up the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Chapter 3: Understanding the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Power and RPSU LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Fast Ethernet Port Link/Act LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

SFP Fiber Optic Module Link/Act LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

LED Problem Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 4: Using the SFP Fiber Optic Modules . . . . . . . . . . . . . . . . . . . . . 37Inserting SFP Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Removing SFP Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

10

316860-D

Inserting and Removing an SFP Module Fiber Optic Cable . . . . . . . . . . . . . . . . . . . . 41

Appendix A: Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Ethernet Routing Switch 1600 Series switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

AC power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

System-level regulatory requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Standards supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Data rate and encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Mean Time Between Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Performance specifications (64-byte packets) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Address database size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SFP Fiber Optic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Transmitter electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Transmitter optical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Receiver electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Receiver optical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Appendix B: Translation of Safety Messages . . . . . . . . . . . . . . . . . . . . . . . 51

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

11


Figures

Figure 1 Ethernet Routing Switch 1648T Front Panel . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 2 Ethernet Routing Switch 1624G Front Panel . . . . . . . . . . . . . . . . . . . . . . 23

Figure 3 Ethernet Routing Switch 1612G Front Panel . . . . . . . . . . . . . . . . . . . . . . 24

Figure 4 1648 model- rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 5 Rubber Feet and Mounting Bracket Attachment Points . . . . . . . . . . . . . . 28

Figure 6 Mounting the Switch in a 19-inch Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 7 LED indicators on the 1648T switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 8 Inserting the SFP Fiber Optic Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 9 Lever-type SFP Fiber Optic Module Removal . . . . . . . . . . . . . . . . . . . . . 40

Figure 10 Slider-type SFP Fiber Optic Module Removal . . . . . . . . . . . . . . . . . . . . . 41

Figure 11 Fiber Optic Cable Insertion and Removal . . . . . . . . . . . . . . . . . . . . . . . . . 42

12

316860-D

13


Tables

Table 1 Power and RPSU LED status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 2 Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 3 Fast Ethernet Port Link/Act LED status . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 4 LED problem indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

14

316860-D

15

Installing the Ethernet Routing Switch1600 Series Switch

Preface

The Ethernet Routing Switch 1600 Series is a fixed port hardware-based Layer 3 routing switch that supports three models:

• the Ethernet Routing Switch 1612G 12 small form factor (SFP) GBICs, which provides small to medium aggregation

• the Ethernet Routing Switch 1624G 24 SFP GBICs, which provides small to medium aggregation

• the Ethernet Routing Switch 1648T 48 10/100, plus 4 SFP GBICs, which provides small edge concentration

The Ethernet Routing Switch 1600 Series Layer 3 routing switch can reside in the wiring closet (1648T) and in the data center or network core (1612G and 1624G). The Ethernet Routing Switch 1648T provides Layer 3 functionality in the wiring closet with 48 10/100 ports and 4 GBIC ports. The Ethernet Routing Switch 1612G and 1624G provide 12 and 24 gigabit Ethernet ports for wiring closet aggregation as well as high-speed connections for servers and power users. These types of aggregation devices typically reside in the network core or data center, but can be placed anywhere.

This guide provides instructions on how to install the Ethernet Routing Switch 1600 Series switch in an equipment rack.

This guide also describes some of the routine tasks of operating the Ethernet Routing Switch 1600 Series switch, and includes technical specifications.

16 Preface

316860-D

Before You Begin

This guide is intended for qualified service personnel who are installing the Ethernet Routing Switch 1600 Series switch for the first time. A qualified service person should have appropriate technical training and experience and be aware of the hazards involved in installing and replacing customer-replaceable units.

Before installing the Ethernet Routing Switch 1600 Series switch, ensure that all network wiring has been installed on the premises using standard cable-system practices.

Text Conventions

This guide uses the following text conventions:

Related Documentation

This section lists the documentation specific to the 1600 Series platform. Current versions of technical documentation for the 1600 Series can be downloaded from the Nortel Support Portal at http://www.nortel.com/support.

Technical manuals and release notes can be printed and copied freely from the Internet. Documents acquired from the Internet can be viewed, printed, and searched using Adobe Reader*. Adobe Reader can be downloaded for free from the Adobe web site.

italic text Indicates new terms, book titles, and variables in command syntax descriptions. Where a variable is two or more words, the words are connected by an underscore.

plain Courier text

Indicates command syntax and system output, for example, prompts and system messages.

http://support.avaya.com



Preface 17


The following list outlines the documenation in the 1600 Series suite:

• Configuring QoS and Filters using the CLI and Device Manager (Part Number 321822-A)

• CLI Command Line Reference for the Ethernet Routing Switch 1600 Series Switch (Part Number 316862-D)

• Configuring Network Management using the CLI and Device Manager (Part Number 321816-A)

• Configuring VLANs, Spanning Tree, and Static Link Aggregation using the CLI (Part Number 321717-B)

• Configuring VLANs, Spanning Tree, and Static Link Aggregation using Device Manager (321718-B)

• Installing and Using Device Manager (Part Number 321818-A)

• Configuring IP Routing and Multicast Operations using the CLI (Part Number 321711-B)

• Configuring IP Routing and Multicast Operations using Device Manager (Part Number 321712-B)

• Configuring and Managing Security using the CLI (Part Number 321714-B)

• Configuring and Managing Security using Device Manager (Part Number 321713-B)

• Quick Start Guide (Part Number 321819-A)

• Getting Started (Part Number 321821-A)

• Installing the Ethernet Routing Switch 1600 Series Switch (Part Number 316860-D)

• Upgrading to Ethernet Routing Switch 1600 Series Software Release 2.1 (Part Number 321327-B)

• Network Design Guidelines (Part Number 321823-A)

• Managing Platform Operations (Part Number 321817-A)

• System Messaging Platform Reference Guide (Part Number 321820-A)

• Release Notes for the Ethernet Routing Switch 1600 Series, Software Release 2.1 (Part Number 316859-J)

18 Preface

316860-D

Technical Documentation

Up to date technical documentation can be downloaded from the Nortel support portal at http://www.nortel.com/support.

If, for any reason, you cannot find a specific document, use the Search function:

1 Click Search at the top right-hand side of the web page.

The Search page opens.

2 Ensure the Support tab is selected.

3 Enter the title or part number of the document in the Search field.

4 Click Search.

Technical manuals and release notes can be printed freely from the Internet. Use Adobe* Reader* to open the manuals and release notes, search for sections, and print them on most standard printers. The Adobe Reader can be downloaded from the Adobe web site.

How to Get Help

If a service contract for the Nortel product was purchased from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance.

Ifa Nortel service program was purchased, go to http://www.nortel.com/help to locate information to contact Nortel for assistance:

• To obtain Nortel Technical Support contact information, click the CONTACT US link on the left side of the page.

• To call a Nortel Technical Solutions Center for assistance, click the CALL US link on the left side of the page to find the telephone number for your region.

http://www.avaya.com/gcm/master-usa/en-us/tasks/connect/contacts/sales/salescontact.htm


Preface 19


An Express Routing Code (ERC) is available for many Nortel products and services. When you use an ERC, your call is routed to a technical support person who specializes in supporting that product or service. To locate the ERC for your product or service, go to http://www.nortel.com/help and follow these links:

1 Click CONTACT US on the left side of the HELP web page.

2 Click Technical Support on the CONTACT US web page.

3 Click Express Routing Codes on the TECHNICAL SUPPORT web page.

http://www.avaya.com/gcm/master-usa/en-us/tasks/connect/contacts/sales/salescontact.htm

20 Preface

316860-D

21


Chapter 1Introducing the 1600 Series Switch

This chapter introduces the various 1600 Series switch models and discusses their components. Specifically, the chapter includes the following topics:

Topic Page

Ethernet Routing Switch 1600 Series models 22

Enclosure 22

Power Supplies 25

22 Chapter 1 Introducing the 1600 Series Switch

316860-D

Ethernet Routing Switch 1600 Series models

The 1600 Series switches are available in the following three models:

• Ethernet Routing Switch 1648T

• Ethernet Routing Switch 1624G

• Ethernet Routing Switch 1612G

Each of these models are explained in more detail in the sections that follow.

Ethernet Routing Switch 1648T

The 1648T switch has 48 Fast Ethernet ports and four slots that accept Gigabit Small Form-factor Pluggable (SFP) modules. These Fast Ethernet ports can be connected to remote network devices at either 10 Mb/s or 100 Mb/s. They can automatically detect the highest communication speed and the duplex state (full- or half-duplex) that the remote network device can accept, and configure themselves to provide the highest speed connection possible.

In addition, the 48 Fast Ethernet ports can detect whether a cross-over or straight-through Ethernet cable has been used, and automatically connect the receive and transmit twisted pair wires to the appropriate receive and transmit terminals. This means that a Fast Ethernet network connection to a remote network device can use either a cross-over or a straight-through Ethernet cable, and still maintain a valid link. Figure 1 shows the front panel of the 1648T switch.

Figure 1 Ethernet Routing Switch 1648T Front Panell

Chapter 1 Introducing the 1600 Series Switch 23


The LEDs on the front panel indicate the status of each of the following:

• 48 Fast Ethernet ports

• four Gigabit Ethernet SFP modules

• main and redundant power supplies

Generally, a lit LED indicates a functioning power supply or port. A flashing LED indicates either activity on an Ethernet port, or a failure of one of the two built-in AC power supplies.

Ethernet Routing Switch 1624G

The 1624G switch has 24 slots that accept Gigabit SFP modules for network connections at 1000 Mb/s. Figure 2 shows the Ethernet Routing Switch 1624G front panel.

Figure 2 Ethernet Routing Switch 1624G Front Panel


• 24 Gigabit Ethernet SFP modules

• main and redundant power supply

• out of band 10/100 Management port



316860-D

Ethernet Routing Switch 1612G

The 1612G switch has 12 slots that accept Gigabit SFP modules for network connections at 1000 Mb/s. Figure 3 on page 24 shows the Ethernet Routing Switch 1612G front panel.

Figure 3 Ethernet Routing Switch 1612G Front Panel


• 12 Gigabit Ethernet SFP fiber optic modules

• main and redundant power supply

• out of band 10/100 Management port


Enclosure

Each 1600 Series switch consists of a standard 19” rack-mountable, sheet metal enclosure. Mounting ears are included in the switch’s packaging to allow mounting the switch in a standard 19” electronic equipment rack.

Cooling fans and air vents are located on the sides and the back panel of the enclosure. When mounting the switch, ensure that these cooling fans and vents are not blocked. In addition, you should allow sufficient airflow to prevent the switch from over-heating.

Chapter 1 Introducing the 1600 Series Switch 25


Power Supplies

The 1600 Series switches include two internal power supplies. These units have two AC receptacles for AC power cords and two power on/off switches to control each power supply (Figure 4 on page 25). This provides a redundant power supply (RPSU) in case of failure of either the power supply itself, or the AC circuit.

Figure 4 1648 model- rear panel

When you view the units from the rear, the power supply on the right is the main power supply, while the one on the left is the secondary one that controls the RPSU. When switching over to the RPSU, Nortel recommends that you wait at least 2 seconds (until the RPSU is fully active) before switching off the main power supply.

Note: The 1600 Series switch AC power supplies accept an input voltage of between 100-240 VAC. See Appendix A, “Technical specifications,” on page 43 for additional information on power supply specifications.

RPSU


316860-D

27


Chapter 2Unpacking and Setting up the Switch

This chapter provides unpacking and setup information for the 1600 Series switch. Specifically, it includes the following topics:

Unpacking the Switch

Begin by opening the shipping carton and carefully unpacking its contents. The carton should contain the following items:

• One Ethernet Routing Switch 1600 Series Layer 3 switch

• A mounting kit with two mounting brackets and six screws

• Four rubber feet with adhesive backing

• Two AC power cords (if ordered with appropriate country kit)

• A CD containing the software and documentation for the switch

If any item is missing or damaged, please contact your local Nortel reseller for replacement.

Installing the Switch

When choosing a place to install the 1600 Series switch, use the following guidelines:

Topic Page

Unpacking the Switch 27

Installing the Switch 27

Powering up the Switch 29

28 Chapter 2 Unpacking and Setting up the Switch

316860-D

• Ensure that the surface supports at least 3 kg

• Ensure that the power outlet is within 1.82 meters (6 feet) of the device

• Visually inspect the power cord to see that it is plugged in to the AC power connector

• Ensure that there is proper heat dissipation from and adequate ventilation around the switch

• Do not place heavy objects on the switch

Installing the Switch on a Desktop or Shelf

When installing the 1600 Series switch on a desktop or shelf:

1 Attach the rubber feet included with the device to the bottom of each corner (see Figure 5).

2 Ensure you allow adequate space for ventilation between the device and the objects around it.

Figure 5 Rubber Feet and Mounting Bracket Attachment Points

Installing the Switch in a Rack

The 1600 Series switches can be installed in a standard 19-inch electronic equipment rack or cabinet. Along with the required screws, two mounting brackets are included in the switch’s packaging.

To install the switch in a rack:

Chapter 2 Unpacking and Setting up the Switch 29


1 Attach the mounting brackets to the switch housing using the attachment points (see Figure 5 on page 28).

2 Use the attached brackets to mount the switch in a standard 19-inch electronic equipment rack (see Figure 6).

Figure 6 Mounting the Switch in a 19-inch Rack

Powering up the Switch

The 1600 Series switch can be used with an AC power supply of 100–240 VAC, 50–60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The power supply of the switch adjusts to the local power source automatically. The switch can be powered on without having any, or all of the LAN segment cables connected.

After you turn the power on, the LED indicators should respond as follows:

• All LEDs blink momentarily to represent a system reset.

• The power LED turns on and stays on as long as power is supplied.

Note: The required screws or nuts and bolts required to mount the switch to the 19-inch rack should be supplied by the rack manufacturer.

30 Chapter 2 Unpacking and Setting up the Switch

316860-D

• Depending on the transmission speed, the 100M LED remains on.

31


Chapter 3Understanding the LEDs

This chapter provides information for the 1600 Series switch LEDs. Specifically, it includes the following topics:

Status Information

The Ethernet Routing Switch 1600 Series switches have LEDs on their front panels that indicate the status of the power supply, the secondary power supply, the link between a port and a remote network device, and the presence of activity on that link.

Figure 7 on page 32 shows the LED indicators for the 1648T switch. The LEDs for the other switches in the 1600 Series display identical information. However, their layout can differ. Note that the 10/100 out of band Management port and its LEDs are unique to the 1612G/1624G models.

The 10/100 out of band Management LEDs specify the following:

• Speed: 10Mbps (green off)/ 100Mbps (green on)

• Link/Act: link (steady green)/ activity (flashing)

Topic Page

Status Information 31

Power and RPSU LEDs 32

Status LED 33

Fast Ethernet Port Link/Act LEDs 34

SFP Fiber Optic Module Link/Act LEDs 34

LED Problem Indicators 35

32 Chapter 3 Understanding the LEDs

316860-D

Figure 7 LED indicators on the 1648T switch

When the switch is first started, all of the port Link/Act LEDs flash once. The Status LED then flashes to indicate that the switch is booting and performing its Power On Self Test (POST) routine. At the end of the boot sequence, the LEDs begin their normal functions.

Power and RPSU LEDs

Each 1600 Series switch has two identical AC power supplies with independent AC main connections, as well as independent AC power switches on the rear panel of the switch. Each of these power supplies is capable of fully powering the 1600 Series switch.

If both power supplies are connected to the AC main circuit they operate in load-sharing mode. Consequently, if one of the power supplies fails, the remaining power supply then carries the full power load. The Power and RPSU LEDs work in concert to display the status of the two 1600 Series switch power supplies.

Note: The 1600 Series switches have on/off switches on the rear panel for each of the two internal power supplies (see Figure 4 on page 25). These switches must be in the On position for AC power to reach each of the power supplies.

Chapter 3 Understanding the LEDs 33


Table 1 describes the Power and RPSU LEDs and their behavior.

In the unlikely event that both the main power supply and the redundant power supply fail, there is no electrical power to light any LEDs. This circumstance can also arise if you connect the switch to the main AC circuit with both the AC power switches on the rear panel of the 1600 Series switches in the Off position.

Status LED

Table 2 describes the Status LED and its behavior.

Table 1 Power and RPSU LED status

Power LED RPSU LED Description

Steady green Steady green Main AC circuit for both power supplies (as well as the power supplies themselves) are operational. The power supplies are in load-sharing mode.

Steady green Flashing green Primary power supply is operational, while the redundant power supply has failed or is not receiving AC power. Power to the switch is supplied by the primary power supply.

Flashing green Steady green Primary power supply has failed or is not receiving AC power, while the redundant power supply is operational. Power to the switch is being supplied by the redundant power supply.

Off Off No main AC circuit connection to either power supply, or both power supplies have failed.

Table 2 Status LED

Status LED Description

Steady green System has powered up and completed the self-test successfully. It is operating normally.

Flashing green System has powered up, but a failure was detected during the self-test operation.

Off System did not power up.


316860-D

Fast Ethernet Port Link/Act LEDs

Each Fast Ethernet port on the 1600 Series switches has a two color LED that displays the status of the link between the switch and a remote network device (see Table 3).

SFP Fiber Optic Module Link/Act LEDs

On the 1600 Series switches, each Gigabit Ethernet SFP fiber optic module slot contains a green LED. This LED displays the status of the link between the switch and a remote network device as follows:

• If the LED is glowing green, the port is connected to a remote network device at a speed of 1000 Mb/s.

• If the LED is flashing green, there is activity (packets are being forwarded) between the switch and the remote network device.

Table 3 Fast Ethernet Port Link/Act LED status

LED indicator Description

Glowing amber The port is connected to a remote network device at a speed of 10 Mb/s

Glowing green The port is connected to a remote network device at a speed of 100 Mb/s

Either flashing amber or green

There is activity (packets are being forwarded) between the switch and the remote network device

Chapter 3 Understanding the LEDs 35


LED Problem Indicators

Table 4 lists possible problems indicated by the LEDs on the 1600 Series switches and suggests corrective action.

Table 4 LED problem indicators

Symptom Probable cause Corrective action

The Link/Activity LED for a connected port is off or does not blink (and you believe that traffic is present).

The switch is experiencing a port connection problem, or the switch’s link partner is not autonegotiating properly.

Verify that the cable connections to the link partner are correct. Verify port configuration parameters for both ends of the connection. Move the cable to another port to see whether the problem occurs on the new port.

The Link/Activity LED blinks continuously.

There may be a port configuration error.

Verify port configuration parameters for both ends of the connection.

No LEDs are lit. A hardware failure has been detected.

Disconnect the power cord and then reconnect it.


316860-D

37


Chapter 4Using the SFP Fiber Optic Modules

The Ethernet Routing Switch 1648T provides 4 SFP slots, while the 1624G has 24 slots and the 1612G has 12 slots. These slots accept SFP fiber optic modules that operate at 1000 Mbps in full-duplex mode. They can connect fiber optic cables to other network devices. This chapter provides information on these SFP fiber optic modules and includes the following topics:

Topic Page

Inserting SFP Modules 38

Removing SFP Modules 39

Inserting and Removing an SFP Module Fiber Optic Cable 41

38 Chapter 4 Using the SFP Fiber Optic Modules

316860-D

Inserting SFP Modules

SFP modules are sensitive to static electricity. Static discharge from your clothing or other fixtures around you, even at levels that do not create a spark, can cause damage.

Before beginning the installation process, be aware that:

• An SFP module can be installed or replaced in an operating1600 Series switch without turning off power to the switch.

• Use the correct fiber optic cable type to ensure the proper performance of the fiber optic network link.

To install an SFP module:

1 Insert the module into an empty slot on the 1600 Series switch. Figure 8 on page 39 shows the module being inserted in the 1648T model. When doing so, ensure that:

Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables are connected to a light source.

Caution: Electrostatic discharge can damage hardware. To prevent static discharge damage when you work with Ethernet Routing Switch 1600 Series switch modules, place each module on a grounded antistatic mat until you are ready to install it or leave the module in the sealed ESD bag. Also, be sure to wear a discharge leash or wrist strap to free yourself of static before you touch a module.

8769EB

Chapter 4 Using the SFP Fiber Optic Modules 39


a the SFP module is properly aligned with the slot, and that the module’s rear electrical connector is facing down for the two SFP slots on top of the group of four.

b the electrical connectors on the SFP fiber optic module are facing up for the two SFP slots on the bottom of the group of four.

Figure 8 Inserting the SFP Fiber Optic Modules

2 Seat the electrical contacts in the rear of the SFP module are against the contacts in the SFP slot.

3 Gently press the module into the slot until you feel a slight click.

Removing SFP Modules

There are two methods to remove SFP modules. These methods are dependent on the module type, that is whether the module is a lever- or slider-type SFP module.

If it is a lever-type SFP module:

1 Move the small lever from the top of the module down across the front where the fiber optic cable connections are located.

2 Use the lever to gently pull the module out of the SFP slot.

Caution: SFP modules are keyed to prevent improper insertion. If the module resists pressure, do not force it. Remove it, turn it over, and reinsert it.


316860-D

Note that you cannot remove this type of module without first disconnecting the fiber optic cable from the module because the fiber optic cables block the movement of the lever.

Figure 9 shows the removal of a lever-type SFP module from the Ethernet Routing Switch 1648T.

Figure 9 Lever-type SFP Fiber Optic Module Removal

If it is a slider-type SFP module:

1 Retrieve a small tool, such as a ball-point pen.

2 Press the small slider at the bottom front of the module where the fiber optic cable connectors are located.

Pressing this slider forces it against the edge of the SFP slot on the Ethernet Routing Switch 1648T and gently releases the SFP module.

Figure 10 on page 41 shows the removal of a slider-type SFP module from the Ethernet Routing Switch 1648T.

Chapter 4 Using the SFP Fiber Optic Modules 41


Figure 10 Slider-type SFP Fiber Optic Module Removal

Inserting and Removing an SFP Module Fiber Optic Cable

The SFP module fiber optic cable connectors have two small tabs, similar to the tabs on copper Category 5 Ethernet cable, or a telephone cable connector. This tab retains the connector in the SFP module, so that it cannot accidentally be pulled out, causing the loss of the link.

To remove the SFP module fiber optic cable connector from the SFP module:

1 Press down on the retaining tabs on the fiber optic cable connectors.

2 Gently pull the outer plastic casing away from the SFP module.

The connectors on many SFP fiber optic cables are grouped in pairs with a small plastic tab you can use to press both connector tabs at the same time. This allows you to remove both cable connectors as a group.

Figure 11 on page 42 displays the insertion and removal of the SFP fiber optic cables from a SFP module.

Caution: Ensure that the connector on the fiber optic cable is properly aligned. You can insert this connector one way only; if it does not fit, do not force it.


316860-D

Figure 11 Fiber Optic Cable Insertion and Removal

43


Appendix ATechnical specifications

This appendix lists the technical specifications for the Ethernet Routing Switch 1600 Series switches.

Ethernet Routing Switch 1600 Series switches

The physical, environmental, and AC power supply specifications for the three 1600 Series switches are listed in the sections that follow.

Physical specifications

Height: 4.4 cm (1.73 inches)

Rack Units (RUs): 1 U

Width: 44.1 cm (17.3 inches)

Depth: 36.7 cm (14.4 inches)

Weight: 4.2 Kg (1.9 pounds)

44 Technical specifications

316860-D

Environmental specifications

AC power supply specifications

Operating temperature: 0°C to 40°C (32°F to 104°F)

Storage temperature: -25°C to 70°C (-13° to 158°F)

Operating humidity: 85% maximum relative humidity, noncondensing

Storage Humidity: 95% maximum relative humidity, noncondensing

Operating altitude: 3024 m (10,000 ft) maximum

Storage altitude: 3024 m (10,000 ft) maximum

Free fall/drop: NSTA 1A, IEC 68-2-32 Ed, FCC Part 68 D 302©(1)

Vibration: NEBS, TR-NWT-000063, GR-63

Shock/bump: IEC 68-2-27 Ea

Nominal input voltage: 100 to 240 VAC

Input frequency: 47 - 63 Hz

Input current: 4 A at 115 VAC, 2 A at 230 VAC maximum

Input power: 575 W maximum

Inrush current: 30 A at 115 VAC, 50 A at 230 VAC maximum

Output current: +5V - 1 A

+12V - 10 A

Output voltage: +5V - from 4.75V to 5.25V

+12V - from 11.40V to 12.60V

Output protection: An over-voltage circuit monitors the output and will shut down the power supply in cases where excessive output voltage, short-circuit, or over-load conditions are detected. For over-load and short-circuit conditions, the power supply will go into auto-recovery mode.

Redundancy fail-over: A TTL logic signal is used to signal the failure of one of the two power supplies built-in to the 1600 Series switches. This signal will react to a power supply failure at least 1 ms before the loss of output voltage regulation.

Safety standards: UL 60950, CSA 22.2 No. 60950,

EN 60950

Technical specifications 45


System-level regulatory requirements

EMI standards: FCC docket 20780 curve “B”,

EN 55 022 “B”, EN6100-3-2

EMS standards: EN61000-4-2, 6KV contact, 8KV airEN61000-4-3, 10V/m criteria A

EN61000-4-4, 2KV criteria A

EN61000-4-5, 2KV criteria AEN61000-4-6, 2KV criteria A

EN61000-4-11

- 30% dip 10ms criteria B- 60% dip 100ms criteria C

- 95% dip 5000ms criteria C

Electromagnetic emissionsregulatory requirements

Global basis for certification: CISPR 22-1997 Class A

US: FCC CFR47 Part 15, Subpart B, Class A

Canada: ICES-003, Issue-2, Class A

Europe EN 55 022-1998 Class A: EN 6100-3-2/A14, EN 61000-3-3 (CE Marking)

Australia/New Zealand: AS/NZS 3548:1995, Class A

Japan: VCCI-V3/97.04, Class A

Electromagnetic immunity regulatory requirements:

Global basis for certification: CISPR 24:1997

Europe: EN 55 024 (CE Marking)

Safety regulatory requirements:

Global basis for certification: IEC 60950 current edition with all CB member deviations

US: UL60950

Canada: CSA 22.2 No. 60950

Europe: EN60950 (CE Marking)

Australia/New Zealand: AS/NZS 3260

Mexico: NOM-019-SCFI


316860-D

General specifications

General specifications including supported standards, data rate and encoding, performance, address database sizes, and Mean Time Between Failure (MTBF) are listed in the sections that follow.

Standards supported

IEEE Std 802.3, 1998 Clause 4 Media Access Control CSMA/CD

IEEE Std 802.3, 1998 Clause 14 10Base T New

IEEE Std 802.3, 1998 Clause 21 100Base T

ANSI/IEEE Std 802.1D, 1998 Media Access Control (MAC) Bridges

IEEE 802.1Q Virtual Bridged Local Area Networks

IEEE Std 802.3, 1998 Clause 34-42

IEEE Std 802.3, 1998 Clause 31 (MAC Control)

Data rate and encoding

10 Mb/s Manchester encoding

100 Mb/s 4B/5B encoding

1000 Mb/s 8B/10B encoding

Mean Time Between Failure

Ethernet Routing Switch 1612G: 177,000 hours

Ethernet Routing Switch 1624G: 158,000 hours

Ethernet Routing Switch 1648T: 153,000 hours



Performance specifications (64-byte packets)

Address database size

Aggregate throughput: 1

Switched forwarding rates: For 10 Mb/s: 14,880 pps maximum

For 100 Mb/s: 14810 pps maximumFor 1000 Mb/s: 1,488,000 pps maximum

Latency: 1

Addressing: 48-bit MAC address

Frame Length: 64 to 1518 bytes (IEEE 802.1Q (Untagged)

64 to 1522 bytes (IEEE 802.1Q Tagged)


316860-D

SFP Fiber Optic Module

SFP fiber optic module transmitter electrical and optical, receiver electrical and optical, and regulatory compliance specifications are detailed in the sections that follow.

General specifications

Transmitter electrical characteristics

Transmitter optical characteristics

Data Rate: 1.0625 Gb/s, typical

1.0 Gb/s, minimum

Bit Error Rate: 10-12, maximum, 1.25 Gb/s using PRBS-1

Fiber length 50/125 µm MMF: 550 m

Fiber length 62,5/125 µm MMF: 300 m

Fibre Channel and IEEE 802.3 (Gigabit Ethernet) compatible.

Typical maximum data rate extends to 1.5 Gb/s

Supply voltage: 3.15 to 3.60 V

Supply current: 220 mA, maximum

Transmit disable voltage: 2 V, minimum

Transmit enable voltage: 0.8 V, maximum

Output power (50 or 62.5 MMF): -9.5 to -4 dBm

Optical Wavelength: 830 to 860 nm

Optical rise/fall time: 260 ps, maximum

Relative intensity noise: -120 dB/Hz



Receiver electrical characteristics

Receiver optical characteristics

Environmental specifications

Regulatory compliance

In addition to all Regulatory Compliance requirements specified elsewhere in this manual, all fiber optic modules (SFPs) used in this equipment shall meet the applicable Laser Standards for Compliance. These standards are as follows:

Single ended data output swing: 185 to 600 mV

Data output rise time: 350 ps, maximum

Data output fall time: 350 ps, maximum

Sensitivity: -18 dBm, minimum

Electrical 3 dB cutoff frequency: 1500 MHz

Optical center wavelength: 770 to 860 nm

Operating temperature: -10 to 85 °C

Storage temperature: -40 to 85 ºC

Laser eye safety: FDA 21(J) CFR, Certificate 9210176-16

EN 60950, Certificate R2179338.01EN 60825-1

EN 60825-2

Electrical safety: CLASS 3862.07Certificate CSA 1034405

CLASS 3862.87


316860-D

51


Appendix BTranslation of Safety Messages

This section provides translations of the Caution, Danger, and Warning messages that appear within this document.

Caution: This device is a Class A product. In a domestic environment, this device can cause radio interference, in which case the user may be required to take appropriate measures.

Achtung: Dieses Gerät ist ein Produkt der Klasse A. In Wohngebieten kann dieses Gerät Funkstörungen verursachen. In diesem Fall muß der Benutzer die erforderlichen Maßnahmen zur Beseitigung ergreifen.

Attention: Ce périphérique est un produit de classe A. Il peut provoquer des interférences radio dans un environnement domestique;si tel est le cas, l ’utilisateur devra prendre les mesures qui s ’imposent.

Precaución: Este dispositivo es un producto de Clase A. En un entorno doméstico, este dispositivo puede ocasionar interferencias de radio, en cuyo caso, el usuario deberá tomar las medidas necessarias.

Attenzione: Il dispositivo descritto nel presente documento è un prodotto di Classe A. Se usato in ambienti domestici, può provocare interferenze radio. In tal caso, l ’utente è tenuto a prendere provvedimenti adeguati.

52 Translation of Safety Messages

316860-D

Translation of Safety Messages 53


Caution: Do not set a Nortel Ethernet Routing Switch Power Supply 15 (RPS 15) or Ethernet Switch Power Supply Unit 10 on top of an [Product Name (short)]. The Power Supply Unit 10 weighs approximately 100 pounds (45 kg) and the RPS 15 weighs approximately 40 pounds (17 kg). The switch housing is not strong enough to support this weight.

Achtung: Stellen Sie keinesfalls eine Nortel Ethernet Routing Switch Power Supply 15 (RPS 15) -Netzstromversorgung oder eine Ethernet Switch Power Supply Unit 10 -Einheit oben auf einen Ethernet Switch 470. Eine Power Supply Unit 10 -Netzstromversorgung wiegt ungefähr 45 kg und ein RPS 15 ungefähr 17 kg. Das Gehäuse des Switches ist nicht für solche Belastungen ausgelegt.

Attention : ne placez pas d’unité d’alimentation Nortel Ethernet Routing Switch Power Supply 15 (RPS 15) ou d’unité Ethernet Switch Power Supply Unit 10 au-dessus de l’Ethernet Switch 470. Les unités Power Supply Unit 10 et RPS 15 pesant respectivement 45 et 17 kg, le boîtier n’est pas assez résistant pour supporter cette masse.

Precaución: No coloque una unidad de fuente de alimentación Nortel Ethernet Routing Switch Power Supply 15 (RPS 15) ni una unidad Ethernet Switch Power Supply Unit 10 en un Ethernet Switch 470. La fuente de alimentación Power Supply Unit 10 tiene un peso aproximado de 45 kg (100 lb) y la unidad RPS 15 pesa alrededor de 17 kg (40 lb), y la caja del interruptor no puede aguantar este peso.

Attenzione: non posizionare un alimentatore Nortel Ethernet Routing Switch Power Supply 15 (RPS 15) o un’unità Ethernet Switch Power Supply Unit 10 sulla parte superiore di uno Ethernet Switch 470. L’alimentatore Power Supply Unit 10 pesa circa 45 kg (100 libbre) mentre l’unità RPS 15 pesa circa 17 kg (40 libbre) e il rivestimento dello switch non è sufficientemente resistente per sostenere questo peso.


316860-D

Caution: When mounting this device in a rack, do not stack units directly on top of one another in the rack. Each unit must be secured to the rack with appropriate mounting brackets. Mounting brackets are not designed to support multiple units.

Achtung: Wenn diese Einheit in einem Rack montiert wird, muß ein gewisser Abstand zur nächsten Einheit gelassen werden. Jede Einheit muß mit geeignetem Befestigungsmaterial gesichert werden. Das Befestigungsmaterial ist nicht für die gleichzeitige Befestigung mehrerer Einheiten geeignet.

Attention : si vous installez le module dans une baie, ne l’empilez pas directement sur un autre. Chaque module doit être fixé à sa propre baie à l’aide des supports de montage appropriés. Ces supports ne sont pas conçus pour résister à plusieurs modules.

Precaución: Cuando monte este dispositivo en un bastidor, no apile las unidades directamente una encima de otra. Cada unidad debe fijarse en el bastidor con las abrazaderas de montaje adecuadas. Las abrazaderas de montaje no están diseñadas para sostener varias unidades.

Attenzione: se il dispositivo viene installato in un rack, non impilare le unità direttamente una sull’altra. Ogni unità deve essere fissata al rack con le staffe di montaggio appropriate. Le staffe di montaggio non sono state progettate per supportare più unità.



Danger: Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the switch may result in excessive emissions.

Vorsicht: Verwenden Sie nur Netzkabel mit Schutzerdung. Ohne ordnungsgemäße Schutzerdung besteht für Personen, die den Switch berühren, die Gefahr eines elektrischen Schlages. Eine nichtvorhandene Schutzerdung kann zu sehr starken Abstrahlungen führen.

Danger: n ’utilisez que des cordons d ’alimentation équipés de trajet de mise à la terre. Sans mise à la terre adaptée, vous risquez de recevoir une décharge électrique en touchant le commutateur. Par ailleurs, l'absence de trajet de mise à la terre peut générer des émissions excessives.

Peligro: Utilice únicamente cables de alimentación con toma de tierra. De lo contrario, al tocar el interruptor puede recibir una descarga eléctrica. Si no hay un circuito de toma de tierra en el enchufe, puede producirse un exceso de emisiones.

Pericolo: Utilizzare esclusivamente cavi di alimentazione dotati di un percorso per la messa a terra. Senza un ’adeguata messa a terra, chiunque tocchi lo switch corre il rischio di ricevere una scossa elettrica. L ’assenza di un percorso per la messa a terra erso lo switch può comportare un eccesso di emissioni.


316860-D

Warning: Disconnecting the AC power cord is the only way to turn off AC power to this device. Always connect the AC power cord in a location that can be reached quickly and safely in case of an emergency.

Warnung: Das Gerät kann nur durch Ziehen des Netzsteckers ausgeschaltet werden. Schließen Sie das Netzkabel an einer Steckdose an, die in Notfällen schnell und sicher zugänglich ist.

Avertissement: pour mettre le module hors tension, vous devez impérativement déconnecter le cordon d'alimentation. En outre, vous devez dégager un espace minimal dans la zone de câblage pour pouvoir y accéder facilement en cas d'urgence.

Advertencia: Para apagar el dispositivo debe desenchufar el cable. Conecte siempre el cable de alimentación a una toma segura y de fácil acceso por si se produjera alguna situación de emergencia.

Avviso: l ’unico modo per disattivare questo dispositivo consiste nello scollegare il cavo di alimentazione. Collegare sempre il cavo di alimentazione ad una presa che sia facilmente e rapidamente accessibile in caso di emergenza.



Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables are connected to a light source.

Vorsicht: Glasfaserkomponenten können Laserlicht bzw. Infrarotlicht abstrahlen, wodurch Ihre Augen geschädigt werden können. Schauen Sie niemals in einen Glasfaser-LWL oder ein Anschlußteil. Gehen Sie stets davon aus, daß das Glasfaserkabel an eine Lichtquelle angeschlossen ist.

Avertissement: L’équipement à fibre optique peut émettre des rayons laser ou infrarouges qui risquent d’entraîner des lésions oculaires. Ne jamais regarder dans le port d’un connecteur ou d’un câble à fibre optique. Toujours supposer que les câbles à fibre optique sont raccordés à une source lumineuse.

Advertencia: Los equipos de fibra óptica pueden emitir radiaciones de láser o infrarrojas que pueden dañar los ojos. No mire nunca en el interior de una fibra óptica ni de un puerto de conexión. Suponga siempre que los cables de fibra óptica están conectados a una fuente luminosa.

Avvertenza: Le apparecchiature a fibre ottiche emettono raggi laser o infrarossi che possono risultare dannosi per gli occhi. Non guardare mai direttamente le fibre ottiche o le porte di collegamento. Tenere in considerazione il fatto che i cavi a fibre ottiche sono collegati a una sorgente luminosa.


316860-D


59

Index

Numbers1600 Series switch

before inserting SFP modules 38displaying status information 31enclosure 24Fast Ethernet port 34general specifications 46

data rate and encoding 46, 47performance specifications 47standards supported 46

inserting and removing SFP module cables 41inserting SFP modules 38installation guidelines 27installing on a desktop or shelf 28installing the switch in a rack 28models 22

Passport 1612G 24Passport 1624G 23Passport 1648T 22

power supplies 25power supplies, load sharing mode 32powering up the switch 29

LED response 29POST routine 32

removing SFP modules 39lever-type module 39slider-type module 40

SFP fiber optic moduleenvironmental specifications 49general specifications 48receiver electrical characteristics 49receiver optical characteristics 49regulatory compliance 49specifications 48transmitter electrical characteristics 48

transmitter optical characteristics 48shipping carton, contents 27technical specifications 43unpacking the switch 27

Bbefore inserting SFP modules in the 1600 38

Ccustomer support 18

Eenclosure, 1600 Series switch 24

FFast Ethernet port Link/Act LED 34

Ggeneral specifications 46

address database size 47data rate and encoding 46, 47standards supported 46

Iinserting and removing cables in 1600 switch 41

inserting SFP modules in the 1600 switch 38

installation guidelines for the 1600 switch 27

installing the 1600 Series switchin a rack 28on a desktop of shelf 28

60 Index

316860-D

LLEDs

1612G front panelstatus indicators 24

1624G front panelstatus indicators 23

1648T front panelstatus indicators 23

displaying status information 31Fast Ethernet port Link/Act 34problem indications 35response at startup

Link/Act and Status LEDs 32SFP fiber optic module 34Status 33

load sharing mode, 1600 Series switch 32

Mmodels, 1600 Series switch 22

Passport 1612G 24Passport 1624G 23Passport 1648T 22

PPassport 1612G

12 Gigabit SFP modules. See SFP fiber optic modules 24

front-panel LED status indicators 24

Passport 1624G24 Gigabit SFP modules. See SFP fiber optic

modules 23front-panel LED status indicators 23

Passport 1648T48 Fast Ethernet ports 22front-panel LED status indicators 23technical specifications 43

AC power specifications 44electromagnetic emissions 46environmental specifications 44physical specifications 43safety agency approvals 46

system-level regulatory requirements 45

POST routine 32

power supplies, 1600 Series switch 25

powering up the 1600 Series switch 29

product support 18

Rremoving SFP modules in the 1600 switch 39

SSFP fiber optic module 22

environmental specifications 49general specifications 48Link/Act LED 34receiver electrical characteristics 49receiver optical characteristics 49regulatory compliance 49specifications 48transmitter electrical characteristics 48transmitter optical characteristics 48

shipping contents for 1600 Series switch 27

Status LED 33

support, Nortel 18

Ttechnical specifications 43

technical support 18

troubleshooting LED problems 35

Uunpacking the 1600 Series switch 27

Installing the Ethernet Routing Switch 1600 Series Switch ...

Documents

Transcript of Installing the Ethernet Routing Switch 1600 Series Switch ...