ET V2/3S Series -...

Instruction manual

190527

ET100 V2 PNP ET115 3S PNP ET125 V2 PNP

NO RX FM800 RX2A PRO DSM2 AC900(S-FHSS+D16)

ET V2/3S Series

User manual and video please visit:WWW.LDARC.COM

Note: 2S configuration using 3S battery will cause damage to electronic equipmentET100 V2 ET115 3S ET125 V2

Only 2SInput Voltage

Wheelbase

Motor

Prop

Battery

100mm

XT1103-7800KV

1935

7.4V 450mAh 80C(JST)

78.6g

115mm

XT1105-5000KV

2345

11.1V 600mAh 50C(XT30)

97.3g

125mm

XT1104-7500KV

2840

7.4V 550mAh 80C(JST)

96.7g

Flytower 20*20(V2) F411+OSD FC+4in1 ESC 12A BLHeliS

VTX Q100 VTX(25mW/100mW 16CH)

Camera OV231(800TVL 150。

NTSC)

Receiver FM800,RX2A PRO,DSM2,AC900(S-FHSS+D16)

Name

2-3S Only 2SWeight

(not include battery&receiver)

ET100 V2 Configuration

Package List

PNP*11935 Prop*4Pairs(Color random)Suitcase*1 7.4V 450mAh 80C*1(JST)

ET Canopy×１

-1-

ET100 V2/115 3SRed Canopy×１ Paper Stickers*1

Wheelbase：100mm

Flytower 20*20(V2)：

F411+OSD

4in1 12A BLheliS

VTX：Q100(25mW/100mW 16CH)

Camera：OV231(800TVL 150。

NTSC)

Motor：XT1103-7800KV

Prop：1935

Battery：7.4V 450mAh 80C(JST)

Voltage：7.4V

Weight：78.6g(not include battery and receiver)

Receiver：FM800,RX2A PRO,DSM2，

AC900(S-FHSS+D16)

ET100 V2/115 3SClear Black Canopy×１

Package List

-2-

Wheelbase：115mm


F411+OSD

4in1 12A BLheliS



NTSC)


Prop：2345

Battery：11.1V 600mAh 50C(XT30)

Voltage：11.1V



AC900(S-FHSS+D16)

PNP*1 11.1V 600mAh 50C*1(XT30)2345 Prop*4Pairs(Color random)Suitcase*1

ET Canopy×１ ET100 V2/115 3SRed Canopy×１ Paper Stickers*1ET100 V2/115 3S

Clear Black Canopy×１

ET115 3S Configuration

Package List

-3-

Wheelbase：125mm


F411+OSD

4in1 12A BLheliS



NTSC)


Prop：2840

Battery：7.4V 550mAh 80C(JST)

Voltage：7.4V



AC900(S-FHSS+D16)

PNP*1 7.4V 550mAh 80C*1(JST)2840 Prop*4Pairs(Color random)Suitcase*1

ET Canopy×１ ET125 V2Red Canopy×１ Paper Stickers*1ET125 V2

Clear Black Canopy×１

4.0V VIN GND VIDEO

25mW

100mW

- +

-

+ VIN 2S-4S Lipo7V-18VGND

LED Frequency table

Click the key change frequency point

Please attention ventilation cooling

AntennaQ100-Mini 25mW/100mW 16CH VTX (2S-4S Lipo 7V-18V)

L=28mm,W=11mm,Weight=2.5g(Without camera and wire)

VTX

ET125 V2 Configuration

-4-

BUZZER-GND

LED STRIP5V(BUZZER+)

TX2VIDEO

CAM

5VG

ND

VID

EOA

UD

IO

VCCGNDSIGNALAUDIO

5VGND

PPM+RX2-INV3V3

BATTERY+ RX25V GND

TX2VIDEO

BATTERY+ RX25V GNDRX2-INV

TX2-INV

CURRENTPWM4

GNDPWM3

GNDPWM2

GNDPWM1

BATTERY+BATTERY+

Supply voltage is 5VNOT invert RX1 signal input

GND5V RX1

TX1

BETAFLIGHT

USB

Supply voltage is 3.3VNOT invert RX2 signal input

5VG

ND

PPM

+R

X2-I

NV

3V3

DSM2/DSMX

GND5V RX1

TX1

5VG

ND

PPM

+R

X2-I

NV

3V3

iBUS etc.

GND5V RX1

TX1

5VG

ND

PPM

+R

X2-I

NV

3V3

SBUS/PPM

Supply voltage is 5VPPM or invert RX2 signal inputS.BUS and PPM receiver connection

Pin definition

DSM2 and DSMX receiver connection

iBUS receiver connection

GNDTX1

GNDVIDEO

GNDAUDIO

GNDBATTERY+BATTERY+

Only KKT-F411(20x20)-90214 version

M4(CW) M2(CCW)

M3(CCW)

Note:pay attention to the direction of rotation of the motor when installing the prop

M1(CW)+ -

M1

M2

M3

M4

AC900(S-FHSS+D16) bind,transmitter(FRSKY X9D/Futaba T18SZ)Bind:Check receiver mode before bind,the first blink after power on indicate the setting, is S-FHSS, is D16FUTABA S-FHSS BIND:Turn on the TX then power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key. Bind procedure is completed and the receiver is working normally when green LED is solidFRSKY D16(NO Telemetry) BIND:Power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key, then set your TX into D16 bind mode. red LED solid meaning bind finished, exit TX from bind mode, receiver’s green LED solid meaning working normally

-5-

ESC

Receiver Bind

Motor

Connect

MATEKF411

3.5.3- MATEKF411 -15-11-2018 13:35(stable)

-7-

BETAFLIGHT firmware allready flash before leave the factory,user just need connect PC to adjust the parameter

1.Open betaflight configuration ,then click ,select FW version

2.Click ,then click to download FW to FC, click after FW

updating finish into setting menu

3.Calibration“Calibrate Accelerometer”

4.Selected UART3,then open“Serial RX”switch and saved

BIND:Power on the receiver while pressing the key,green LED fast blink meaning already in bind mode,user can release the key,then set your TX into bind mode.Green LED turn off and red LED solid mean bind finished,exit TX from bind mode,receiver’sgreen LED solid mean working normally.

RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6)

Firmware Update

-8-

6.PID setting

5.Configuration，select ESC protocol“DSHOT600”，Set up the receiver protocol，then open LED,OSD and DYNAMIC_FILTER

4058

36

3035

-9-

7.Default setting of receiver is 5th channel ARM(AUX1),6th channel mode switching(AUX2)

8.Setting 7th channel mode switching(AUX2).

9.Input“set small_angle = 180 ”,then set

FLIP OVER AFTER CRASH please upgrade the firmware to 3.2.1 version first,then set by BETAFLIGHT

-10-

Name

ET100 V2 PNP NO RX

ET100 V2 PNP AC900

ET100 V2 PNP FM800

ET100 V2 PNP RX2A PRO

ET100 V2 PNP DSM2

ET100 V2 KIT

ET115 3S PNP NO RX

ET115 3S PNP AC900

ET115 3S PNP FM800

ET115 3S PNP RX2A PRO

ET115 3S PNP DSM2

ET115 3S KIT

ET125 V2 PNP NO RX

ET125 V2 PNP AC900

ET125 V2 PNP FM800

ET125 V2 PNP RX2A PRO

ET125 V2 PNP DSM2

ET125 V2 KIT

OV231

Q100 VTX

LED+Buzzer(ET V2/3S Part)

Air Cowling(Φ5 M2)

Factory Code

PNP.ET100 V2.NO RX

PNP.ET100 V2.AC900

PNP.ET100 V2.FM800

PNP.ET100 V2.RX2A PRO

PNP.ET100 V2.DSM2

KIT.ET100 V2

PNP.ET115 3S.NO RX

PNP.ET115 3S.AC900

PNP.ET115 3S.FM800

PNP.ET115 3S.RX2A PRO

PNP.ET115 3S.DSM2

KIT.ET115 3S

PNP.ET125 V2.NO RX

PNP.ET125 V2.AC900

PNP.ET125 V2.FM800

PNP.ET125 V2.RX2A PRO

PNP.ET125 V2.DSM2

KIT.ET125 V2

CAM.OV231

VTX.Q100

PART.LED+BUZZER(ET V2/3S PART)

PRRT.AIR COWLING(Φ5 M2)

Factory Code

PROP.1935.3.WHITE

PROP.2345.3.WHITE

PROP.2840.3.WHITE

BAT.7.4V 450MAH 80C

BAT.7.4V 550MAH 80C

BAT.11.1V 600MAH 50C

PART.BOTTOM PLATE.ET100



MOTOR.XT1103-7800KV

MOTOR.XT1104-7500KV

MOTOR.XT1105-5000KV

FLYTOWER.20*20(V2)

ESC.KK TOWER 12A

FC.F411+OSD(FLYTOWER 20*20 V2)

PART.KK TOWER SCREW(2 LAYER)

PART.KK TOWER WIRE

PART.ET100 V2/115 3S CANOPY

PART.ET125 V2 CANOPY

PART.1.9 PROTERTOR ALL.BLACK



Name

1935 Prop

2345 Prop

2840 Prop

Battery 7.4V 450mAh 80C



Carbon fiber plate(ET100 Part)



XT1103-7800KV

XT1104-7500KV

XT1105-5000KV

Flytower 20*20(V2)

4in1 ESC 12A(KK Tower Part)

F411+OSD FC(V2)

2 Layer Tower Screw(KK Tower Part)

Wire(KK Tower Part)

ET100 V2/115 3S Canopy

ET125 V2 Canopy

1.9 inch black propeller protector(all surround)2.3 inch black propeller protector(all surround)2.8 inch black propeller protector(all surround)

1.Provide free reparation service when find the product defect after purchase.

2.Provide pay-needed reparation service when product damage because improper operation.

3.China customers please contact with the after-sales service,overseas client please contact the dealer.

PNP/RTF Test report ID :

Flight test

Transmitter functions properly

Flying in good condition

Camera OK

VTX OK

QC:

Package check

PNP

RTF

Frame

Transmitter

ID is the same

All parts of the installation

Insulating sleeves have been installed manual

Complete accessories,total packages

QC:

After Sale Service

Product and Factory Code

ET V2/3S Series -...

Documents

Transcript of ET V2/3S Series -...