ENKE-WERK Johannes Enke GmbH & Co. KG - Green Roof Waterproofing... · ENKE-WERK Johannes Enke GmbH...

ENKE-WERKJohannes Enke GmbH & Co. KG

GB

...because it pa

ys to buy qualit

y!Restoration with long-time security

Enke has been facing the challenges of the market since 1924.The high standards fixed by Enke guarantee for the users productsof the highest quality and safety for long-time assurance.

The industry is forced, without interruption, to remove and movegoods from one store to the next. That should be done, for safetyreasons, below a dense roof and on an intact floor.

It has been ensured by Enke for more than 75 years that roofs arewater-tight, that floors are sturdy and that metal roofing isstorm-resistant.

Enke products have become known for their high reliability,even under extreme conditions, beyond the borders of the FederalRepublic of Germany

It is not just by accident that international automobile manufacturersclean up and restore, for instance, their works halls oradministration buildings also outside of Germany for safetyreasons by means of Enke products – whether in Russia, China orin Switzerland. All users like to apply our high-quality productsbecause they do not pose any problems and can be processed ina time-saving manner.

The sum of the advantages, as a consequence, is the fact that theterm Enke has both with customers and processors - become asynonym for high-quality tin sheet bonding techniques as well asroof and floor redevelopment.

We notice this because we hardly have to recommend ourselves– we are being recommended!

We are especially proud of the loyalty of our major customerswho partly have, again and again, requested already for decadesonly the Enke products that have proven their worth under practicalconditions.

This is a nice achievement for a medium-sized specialized enterprise.

Enke is a product that can be recommended without reservations.

We about us

2

Restoration with long-time security

3

www.enke-werk.de

EnkoClean

Special Cleanserfor all cases


4

SteinReiniger

EnkoCleanBio

KunststoffReiniger

EnkoCleanBio

WachsEntferner

EnkoClean

Environment protecting mild Eco Special Cleanser.For façades, bricks, tiles, limestone, clinker, plaster, concrete,concrete stones, terrace slabs, terrazzo, concrete floor slabs as wellas all artificial stones.

Environment-protecting mild Eco Universal Cleanser.For all plastic materials, anodized materials, tarpaulins, tents, caravans,mobile homes, boats and sun blinds and awnings.

Removes old floor polish layers from stone floors.Easily dissolves old floor polish and wax layers as well as acrylic layersfrom natural and artificial stones.

Removes cement skin and surface laitance fromacid-resistant stones and tiles.Depending on the thickness of the cement skin andthe acid-resistant properties of the underground, apply either in concentratedcondition or diluted with water at a maximum of 1:10.

Entferner

EnkoClean

Zementschleier

We have enlarged our range of EnkoClean products.We supply all articles presented in our catalogue in handy 1 ltr. bottles.Our representatives in the field are at your disposal for comprehensive and detailed information.For quick information, contact our telephone line under +49(0)211/304074-76.

AfterBefore

AfterBefore

AfterBefore

AfterBefore


5

Cleans all acid-resistant stone tiles as wellas special steel and chrome-plated surfaces.Removes reliably and without impairment of the joints all tracesof lime scum, soiling, grease, metal oxide, corrosion and soot.

Protects stone and concrete surfaces againstpenetrating moisture.This impregnation agent is particularly suitable for lime stone,brick work, concrete, plaster, roof tiles, fibre cement, artificialstone and sculptures.

Removes oil and bitumen from concretesurfaces, walls and stone floors.Makes bitumen and oil stains immediately solvable and can,as a consequence, also be used for the cleaning of tools.

Creates a clear, glossy protective layeron natural and artificial stones .For unglazed ceramic tiles, terrazzo, clinker, fibre cement,Solnhofen slabs, marble, slate and terrace slabs.Has a freshening up effect.

Removes green sediments,moss and soiling.To be applied only in locations of the sanitary range on allsurfaces made of stone, glass, wood, concrete and ceramics.

FliesenReiniger

EnkoClean

EnkoClean

BitumenLöser

EnkoClean

SteinGlanz

EnkoClean

AfterBefore

SiliconImprägnierung

Entferner

EnkoClean

Algen Moos

AfterBefore

6

EnkoClean, the new product range from Enke at one glance.

EnkoCleanfrom professionals for professionals

www.enke-werk.de

www.enke-werk.de www.enke-werk.de

www.enke-werk.de

www.enke-werk.dewww.enke-werk.de

www.enke-werk.de


7

www.enke-werk.de

Enkolit®

Bonding with

security

Mind the marking

of the manufacturer

Cold bonding agentfor tin sheets

for permanent bonds


8

No extension problems

No unsightly bulges

More time gained

Long-time functionalsecurity formore than 30 years

Museum Quarter in Vienna

Enkolit®

Canton Bank in Weinfelden

Main station in Leipzig

under practical conditions



9

Congress Building in Salzburg

Braun AG in Melsungen

Casino in Baden near Vienna

Enkolit® is a plastic flat coat and tin sheet cold bondingmass on bitumen basis with excellent bonding and adhesiveproperties on brick work, concrete, zinc, copper, aluminium,steel and wood.

Examinations at wall coverings confirm a functional security formore than 30 years of the tin sheets bonded by means of Enkolit®.Test Certificates are available.

Enkolit® meets all requirements of DIN 1055/Part 4 as regardswind suction forces and has an additional noise-abat-ing effectduring rain or hail.

Enkolit® is homologated pursuant to the Guidelines for theexecution of metal roofs, outside wall metal coverings and buildingplumber work. (Section 3.5.3. Adhesive Bonds, Issue September 1991)

Prerequisitesfor the bonding of tin sheets

1. Dry, clean and firm underground

2. Proper denticulation of the spatula

3. Full-surface coating in one direction

4. Mechanical fixed point in the case of inclined or vertical surfaces

5. The tin sheet must be pressed on slowly and uniformly

6. Processing not below + 5 °C

7. On principle, read Application Instructions first

8. Do not use inside of rooms

Supplied in: Tin packing drums with 11 or 32 kg b.f.n. Cartouche 310 ml

Consumption: approx. 2 – 3 kg/m2

Density: approx. 1.1 g/cm3 / 20 °C

Application purpose,fields of use,properties of materials

Enkolit® can be applied for bonding andsealing purposes of metal profiles and metaltin sheet, e.g. made of titanium zinc, copper,aluminium, special steel and copper on otherbuilding materials..

The strength values achieved meet the DINStandard 1055 “Design Loads for Buildings(wind loads)”, which can be proven by neutralexpert opinions on bonds that are up to30 years old.

In the case of large-area placement ofassemblage of façades roofs, etc. the strip-wise or partial surface Enkolit® bonding willallow an improvement of the level fixationof the assemblage surface in the visual range.

Enkolit® is a permanent bonding and sealingagent that can be used without any problemsfor bonding purposes in the case of windowsill and wall coverings.

In the same way, verge flashing and eavestin sheet as well as metal sheathing can bebonded by means of Enkolit®.

Hollow spaces are avoided on account ofthe full surface, rich and closely fittingbonding with Enkolit® . In addition, thebonding has a noise attenuation effect.Drum noises during rain are avoided andthe nesting of insects is prevented. What ismore, Enkolit® prevents corrosion damagedue to moisture at the lower side of thetin sheet.Enkolit® will not run down, even when freshlyapplied at vertical surfaces, provided it hasbeen applied strictly according to theApplication Instructions. Laboratory tests haveshown that Enkolit® will not run out of thebonding joint up to +110 °C. Enkolit® isresistant to industrial exhaust gases, salt andsea water. It is resistant to red algae andfungicide.

Application Instructions for Bonding Work with Enkolit®

Clean underground Apply Enkolit® with grooved spatula Press in splice plate

Apply Enkolit® on splice plate Press on cover uniformly Cover is finally bonded

10


Metal Protecting Coating (One component)

Adhesion on new plates and sheets securefor long-time endurance, without any pre-treatment

www.enke-werk.de

ProtectMetall

NEW

11


Basis: Weather-resistant acrylic resin

Resistance: To bitumen decomposition products

Viscosity: Approx. 4,000 mPas (thixotropic)

Consumption: Approx. 140 ml/m2 (ap-prox. 200 g/m2)

Colour: Grey (approx. RAL 7040)

Surface: Silky matt

Covering power: High

Drying period: Rapidly drying

Properties:

Very good long-time adhesion propertieson new, weathered and pre-weatheredmetal surfaces. Elastic and flexible intemperatures down to at least -25 °C.

Underground: On new, clean sheets, no special pre-treatment is required (e.g. degreasing).In the case of sheets with an old layer,the adhesion must be tested. In the caseof weathered off and soiled sheets,a thorough cleaning is required, possiblyalso grinding.

Processing Application either by means of brushor roller, or – now new – from spraycan. A fleece or fabric strip can beplaced above soldering seams.

Cleaning of tools: By means of nitro thinner or similar agent.Do not use a turpentine substitute.

Supplied in: Packing drums with 4 or 12 kgwith clamping ring (can be closed again)

Spray can 500 ml

More Quality – More Se-curity!

You know the problem:Clipped-on eave gutters, fascia sheets,pipe bows or downcomers below bi-tuminous roof surfaces are damaged againand again by oxidation acid corrosion.

The reason:Bitumen acids are formed through UVradiation, moisture and oxygen at thesurface and are washed off by rain.These acids are responsible for the factthat metal components lose their protectivelayer or cannot form these protectivelayers in the first place, and they aregradually destroyed, as a consequence.

Enke Metal Protect is a completely novelone-component protective paint coat thatis distinguished by a highly permanentproperty and high covering power.

A special advantage is the fact that onlyold or already painted metal componentshave to be cleaned prior to application.New metal components do neither have tobe cleaned nor to be degreased! With onlyone single layer, it is possible to achieve areliable long-time protection effect againstoxidation acid corrosion.

The processing of Enke Metal Protect iseffected by means of brush, roller or fromthe spray can. A thin, highly tearing-resistantfabric can be located in the painting in theregion of the soldering seams in order toadditionally protect this sensitive area.

Ask for comprehensive advice by ourapplication technicians, covering:

� Enke Metal Protect.� Enkryl® and Enkopur®, the liquid plastic agents, proven under practical conditions, for sealing flat roofs with and without inclined surfaces as well as.� Enkolit® sheet metal cold bonding agent for the secure and permanent fastening of metal coverings.

Technical DataProtectMetall

12


www.enke-werk.de

Roof Layer Covering Systems

Enkryl®

Enkopur®

EnkeprenEnkolor

13


14

The professional sealing agents offered by Enkefor all critical

Joining Problem Zones

www.enke-werk.de

Enkryl®,

Enkopur®, Enkepren


15

Roof ventilators

Would there be a roofer who has not yet facedthe problem to have to permanently seal light domes,venting shafts or chimneys?Or a balcony where the connecting height in the rangeof the door was measured much too small?Where the fixing of a cap flashing piece at penetrationsor supports could be achieved only by time-con-sumingactions?Not to mention the damage done to the plastic or woodprofiles which may be caused when usinga welding torch?

In these cases, the application of Enkopur®, Enkryl®

or Enkepren with Polyflex fleece inset is the most simple,most reliable and most secure solution.All three liquid plastic agents are one-componentagents, which means they can readily be processed.Cumbersome mixing processes can be dispensed with.An additional advantage is as follows:It is possible to apply our products Enkryl® + Enkeprenwithout reservation also in inside rooms – such as in akitchen or in the sanitary sector.

Ventilation shaftsNewel posts

Skylight windows

Lightdomes

Wall connections


16

Processing of a wall connection on cleaned underground.

Roof mountings

1. Apply preliminary coat for improved adhesion. 2. Roll on the primer coat with a thick layer.

3. Insert Polyflex fleece without creases in the primer coat. 4. Apply the cover coat. – Finished!

Door connections


Enkepren Enkryl® Enkopur®

Chemical basis

Free from solvent agents yes yes slight portions

Can be processed in a cold condition yes yes yes

One-component agent yes yes yes

Colour shades black grey silver grey light grey

green

Tin packing drums - 15 kg 12,5 kg

30 kg 30 kg 25,0 kg

17


Reaction primer coat for concrete x - -

Acrylic primer - x -

Universal primer 933 x x x

Enke Polyflex Fleece

Enkepren x

Enkryl® x

Enkopur® x


Bitumen roofs yes yes yes

Concrete roofs yes yes no*

Metal roofs yes yes yes

Inclination necessary yes yes no

Zero roof – suitable no no yes

Can be processed as from 5 °C no no yes

Can be processed as from 10 °C yes yes yes

Fields of application

Bitumen-Latexemulsion

Reinacrylat-dispersion

Polyurethan-prepolymer

Problem zones on roofs ne-cessitate in

Preliminary coat

Fleece typesThe following fleece types areavailable:1. ENKE Polyflex fleece 100 cm wide2. ENKE Polyflex fleece 30 cm wide

Characteristic features

Supplied in

* on fresh concrete


18

Enke Roof CoatingsEnkryl

®, Enkopur

®, Enkepren

Restoration of light domesSimple, quick and secure!

In the field of roof sealing, the sealing of light domes confronts the roofer again andagain with problems. The following working procedure with roof coatings suppliedby Enke is intended to demonstrate to you how simple and permanently you can

also master these problem zones.

� Removal of the loose bituminous waterproof sheeting for roofs and cleaning of the underground, if required by means of primer.

� Application of the roof coating and inserting the Polyflex fleece.

� The cover coat can be applied also wet on wet. These light domes remain dense and leak-proof.

1 2 3


19

www.enke-werk.de

Coating Systems forfloors and balconies

EnkeBetoncoat®

EnkeBetoncoat®

for floors with maximum requirements



20

• high resistant• crack-bridging• seamless• durable• ecologically friendly• physiological impeccable

Floor Coating SystemsSolvent-free reaction resin systems (PUR, EP, PMMA)

for maximum requirements

www.enke-werk.de

EnkeBetoncoat®

21

Enke Betoncoat® PUR Layer Compositions

Characteristic Data ofPUR Layer Compositions

Thickness of layer: approx. 3 mmHardening time: approx. 24 hours each (20°C)Chemical resistance: approx. 24 hours eachEnvironmental compatibility: fulfilledPressure resistance: approx. 75 N/mm2

Bending strength: approx. 28 N/mm2

Sealing 1K

PUR Coating

Primer 2K

Sealing 2K Aqua

PUR Coating

Coat of sand

Primer 2K


22

Enke Betoncoat® PUR Processing Instructions

BLASTRAC – Shot peening device

Grinding device

Other ProcessesOther processes, such as flame descaling, sandblasting, high or maximumpressure water jet technology play only in special cases a role and willnot be dealt with in detail in this connection. It is to be recommended,however, to engage an experienced special enterprise for the preparationof the underground.


23


Primer Coatingwith reaction resins

Components A + B arecompletely mixed andthoroughly mixed by meansof a suitable impeller toachieve a homoge-nous result.

Pour out the primer and applyuniformly by means of a roller,while the pores are denselysealed – avoid the formationof major puddles.

For an underground consisting of concrete, cement composition flooras well as other floors with mineral binding, Primer 2K will be used. Anunderground made of old PUR – or EP – reaction resin cover layersor metals require the application of Primer 2K Aqua (the undergroundmust, in this case, be absolutely free from grease). In this case it shouldbe examined, in any case, whether the old surface cover is still suit-able for the acceptance of an over-coating, that means whether it isconnected still firmly enough with the underground. For instructions forthe selection of the most suitable primer, please see the Primer Tableoverleaf. In general, the following should be taken into account:In case the underground to be coated consists of unknown materialsor of materials the properties of which cannot unequivocally bedetermined or if adhesion problems are to be expected, due toinsufficient self-strength of the underground, it will become necessaryto carry out adhesion tension tests, for instance by means of theHERION device. The average adhesion tension strength must amountto 1,5 N/mm2 in which connection the smallest individual value is notallowed to be smaller than 1,0 N/mm2 . The primer coating must alwaysbe applied with pores, if any, being densely sealed. The primer coatcan, if required, be slightly sandblasted.



24


Application of PUR coatingor PUR asphalt coating

ENKE CONCRETE COAT – polyurethane coating (PUR coatingor PUR asphalt coating) is allowed to be applied only on thoseundergrounds that have properly been pre-treated accordingto our Application Guidelines. PUR coating is supplied withoutpigments and should, as a consequence, be always sealed bymeans of a colour component. The sealing not only will increasethe abrasion resistance but also ensures a satisfactory colourshade and yellowing stability. Coats without sanding can besupplied with Sealing 1K, skid-proof surfaces should be sealedafter sweeping off of the loose quartz sand with Sealing 2K incolours. See also, in this connection, the Processing Instructionsunder “Application of Sealing 2K Aqua”.

It should be taken into account that Sealing 1K is allowed to beapplied only on completely smooth undergrounds.See also, in this connection, the Processing Instructions under“Application of Sealing 1K”.

Initially, stir up Component A by meansof a compulsory mixer, then add Compo-nent B completely and mix both compo-nents very thoroughly until complete ho-mogeneity has been achieved. (We rec-ommend filling the mixed coating massinto a clean, dry neutral vessel and sub-sequently mixing it again thoroughly).

Pour out the coating mass and apply ituniformly by means of a teethed spatula.In the case of larger smooth surfaces,the coating mass can also be distributedby means of a doctor blade.

25

An underground surface where Sealing 2K Aqua is to be appliedis in most cases coated and equipped with sanding. The sandgrains that are not bound must be removed before the sealingprocess is started. Old coatings made of epoxy resins orpolyurethane types, which are still well preserved and firmlyconnected with the under-ground surface, can be newly processedwithout additional primer directly by means of Sealing 2K Aquain colours. Sealing 2K Aqua is solvent-free, low-odour andstable in colour-shade. The surface is permitted to be used onlyafter the sealing has completely become tack-free.

Materials, tools and auxiliary agents• Enke Concrete Coat – Sealing 2K Aqua• Fleece roller• Cleaning agents for the tools: water• Protective working gloves, Adhesive tape


Applicationof top-coat 2K Aqua

Pour the components A + B completelytogether and mix them thoroughly witheach other (electrical impeller).It is advisable, for instance, to pour thepre-mixed sealing mass into another vessel.

Pour out the mixed Sealing 2K Aquain small portions and distribute themuniformly by means of a roller crosswise.

Consumption on smooth surfaces:

300 – 400 g/m2

Consumption on sanded surfaces:

Min. 600 g/m2

Processing period:approx. 50 minutes (end of potlife cannot berecognized!)*Hardening period: approx. 24 hours

* Do by no means use any material with lapsedpotlife but discard it!


26

Friday morning:Preparation of underground surface

Friday afternoon:Levelling – by means of spatula

Friday evening:Full area primer coating

SaturdayCoating, sanding, if required

Sunday early morningSealing

Monday morning:Taking the floor again

into operation!*


No time lost = more profit!

Time schedule of thecoatingof an industrial floor.(Standard composition)

* Depending on ambient temperature and temperature of the underground


Flat roofs of all types

Balconies and terraces

Prefabricated garages and transformationstations made of concrete

Floors in works and storage halls, garages,laboratories, hospitals, etc.

Metal sheet bondingon nearly all building undergrounds

Building metals

Industrial glazing

There are Videos showing the proper processingof our products available for you on request.Make use of the technical advantage of the Enke qualityproducts, with a security of partly more than thirtyyears functional safety!

Enke products are produced for the protection of secure long-time sealingand restoration of the building substance.

Especially for:

27


www.enke-werk.de

ENKE-WERK · Johannes Enke GmbH & Co. KGHamburger Straße 16 · D-40221 Düsseldorf-HafenTel: +49 (0) 211/304074-76 · Fax: +49 (0) 211/393718e-mail: [email protected] · Internet: www.enke-werk.de

Dealer:

Cop

yrig

ht: E

NKE

-WER

K · J

ohan

nes

Enke

Gm

bH &

Co.

KG

· Ä

nder

unge

n vo

rbeh

alte

n (1

0.03

/100

0) O

.A.

...because it pa

ys to buy qualit

y!


ENKE-WERK Johannes Enke GmbH & Co. KG - Green Roof Waterproofing... · ENKE-WERK Johannes Enke GmbH...

Documents

Transcript of ENKE-WERK Johannes Enke GmbH & Co. KG - Green Roof Waterproofing... · ENKE-WERK Johannes Enke GmbH...