ENGINE CONTROLS & STEERING

529ENGINE CONTROLS & STEERINGPH: 902-566-1220 [email protected] note, PRICES SUBJECT TO CHANGE due to fluctuating economic conditions and tariffs.

SEASTAR BACK MOUNT KIT Teleflex SeaStar Back Mount Kit for Sea-Star Helm models HH5271-3 (8121105) and HH5272-3 (8121201) is used to reduce your helm's protrusion in tight quarters. Protrusion is reduced by a width equal to the thickness of the dash. Kit can also be used to retrofit the SeaStar 3" helm into 4.5" dash cutouts.

PART NO. MFG# DESCRIPTION PRICE

8121125 HA5418 Back Mount Kit $58.35

HELM SERVICE KIT

Kit includes:1 ea. x Jam Nut 5/8" NF1 ea. x Woodruff Key1 ea. x Seal Ring1 ea. x Top Plate3 ea. x Screws

For most BayStar and SeaStar Helms.PART NO. MFG# DESCRIPTION PRICE

8121103 HP6032 Service Kit $15.68

UNIVERSAL TIE-BARS

Universal Tie-Bars used in a twin engine, single cylinder application.Used on: HC5345-3 (8121340), HC5358-3 (8121346),17.5" long pin-to-pinPlease see single & dual engine application guide.


8130156 HO6001 Universal Tie Bar $683.768130157 HO6003 Tie Bar $691.80

TWIN ENGINE DUAL CYLINDER TIE BAR

For use with twin front mount cylinders in a twin engine/cylinder set up.Used on: HC5345-3 (8121340) HC5358-3 (8121346)22" long pin-to-pin Please see single & dual engine application guide.


8130159 HO6002 Tie Bar for Twin $723.34

TWIN ENGINE SINGLE CYLINDER TIE BAR (HONDA)

Honda Tie-Bar used in a twin engine, single cylinder applicationUsed on: HC5347-3 (8121345) Please see single & dual engine application guide.


8130158 HO5063 Tie Bar $722.69

8130156

8130157

SPACER KIT Spacer kit, for use with cylinder: HC5345-3 (8121340), HC5358-3 (8121346), and HC5348-3.Applied to:

• 115-140 HP Suzuki• 25-60 HP Yamaha and Mercury • 115 HP Yamaha


8121347 HO5090 Spacer Kit For Tie Bar $42.44BULKHEAD FITTING ASSEMBLY

Easily pass pipe, wires or cables through bulkheads and prevent carbon monoxide gases from passing from one enclosure to another. Designed to have a bolt on oval flange tube assembly with two optional low durometer flexible boots as termination fixtures. These are secured by either hose clamps, or straps.

75371617537160*SHOWN ASSEMBLED

CABLE PROTECTORBoot style black plastic cable protector, 4-1/2" base plate, approximately 3" High. Boot can be tightened around cables.

Attach the motor cable control boot without disturbing the cable set-tings. Split the outer grommet and the inner ball in half by splitting the sections. The inner ball is made of a low durometer soft sealing material that allows the ball to swivel to its most efficient position for easy cable operation. The outer covers are made of marine grade composites, and the inner flange has a large area for bedding compound in the motor well or transom. White in colour.

CONTROL CABLE SPLIT GROMMETS

8130171

8130175 8130174

8130173 8130172

Small Hole = .375"Large Hole = 1"


8130171 1820W 1-1/2" Base, 1 Small Hole $10.238130172 1830W 1-1/2" Base, 1 Hole $15.398130173 1835W 1-1/2" Base, 3 Hole $15.398130174 1840W 2" Base, 1 Hole $15.398130175 1845W 2" Base, 3 Hole $15.39

PART NO. DESCRIPTION PRICE

8130170 Cable Protector $6.40


7537160 7730 Bulkhead Flange $29.237537161 7735 Bulkhead Tube $29.23

ENGINE CONTROLS & STEERING

Documents

Transcript of ENGINE CONTROLS & STEERING