Electronic Drum

TD36

Precaution Thank you for purchasing this electronic instrument.For perfect operation and security, please read the manual carefully and keep it for future reference.

Safety Precautions CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the product.

Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. (Figure 1)

5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, install in accordance with the manufacturer s instructions. 8) Do not install near the heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarizedplug hase two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety, if the provided plug does not fit into your outlet. consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs. convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over(Figure 1). 13) Unplug this apparatus during lightning storms or when unused for a long periods fo time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION: Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Always make sure all batteries are inserted in conformity with the +/- polarity markings. Always replace all batteries at the same time. Do not use new batteries together with old ones. Also, do not mix battery types, since this can cause overheating, fire, or battery filuid leakage. Remove the batteries from the instrument if it is not to be used for a long time.

Contents Panel Controls... 2

Assembly Instruction ... 6

Connect... 8

Connecting the Power Supply... 8

Connecting a CD Player, etc.(AUX In jack)... 8

USB MIDI... 8

Connecting Headphone 8

Start to Play the Drum ... 9

Switch the Power On ... 9

Set the Master Volume ... 9

Select Drum Kits ... 9

KIT Button ... 9

CLICK Button ... 10

REC/PLAY Buttion... 11

SONG Button ... 12

TEMPO/TAP Button ... 13

Factory Set ... 14

Drum Kits List ... 15

Voice List ... 16

Style List ... 18

MIDI Implementation Chart ... 19

Specifications... 20

1

Panel Controls

Top Panel 1

2

5

Rear Panel

8 9 CONNECT TO BASE RIDE CRASH HI-HAT

Back Panel of bottom case

3 4

6

7

10

SNARE USB

AUX IN PHONES

11 12

13 14 15 POWER CONNECT

ON OFF DC 9V TO MODULE

2

Panel Controls Top Panel

1.MASTER VOLUME

2.[TEMPO/TAP] Button

3.[KIT] Button

4.[CLICK] Button

5.[REC/PLAY] Button

6. [SONG] Button

7.[+][-] Button

This is used to adjust LINE OUT volume, headphone volume and LINE IN volume.

This button is used to change the song's tempo and metronome tempo, allows you to tap the tempo on the pad to change the song's tempo.

This button is used to set the volume and voice of the pad.

This button is used to enter metronome setting display, to adjust metronome volume, metronome sound and type.

This button is used to enter recording display, you can also select user song playing mode.

This button is used to enter the song select display. You can turn off the percussion track of the song, and adjust the song's volume.

This button is used to select the parameters, voices, etc.

3

Panel Controls Real Panel 8. CONNECT TO BASE 9.Trigger Input Jacks 10.USB 11.AUX IN

12.PHONES

Back Panel of bottom case

13.POWER ON/OFF 14.DC 9V 15. CONNECT TO MODULE

This jack is used to connect the module to Back Panel of bottom case. These jacks are used to connect the pads to the Module. (HI-HAT, RIDE, CRASH, SNARE)

This is USB MIDI jack. Connect PC or other USB host devices that support USB audio with a standard USB cable to transfer MIDI data. Connect the output of an external audio device, etc., to this jack (stereo mini jack). This is convenient for playing along with music from a CD or cassette player. Connect a pair of headphones to this jack.

This is the power switch.

Connect an DC adaptor to this jack.

This jack is used to connect Back Panel of bottom case to the module.

The LED dot indicates the SONG/PAD/KIT status; on the status of SONG, the song number

appears on the display; In PAD selection mode, the pad name such as Snare, Crash, and Tom, etc.

Will appear on the display. Press KIT button, the drum kit number will be displayed on the LED.

KIT mode SONG mode PAD name

4

Assembly Instruction Take out the bottom case from the packing

case, insert the drum stand into the bottom

case as shown in the figure and tighten the

T-screw.

Take out the module and three Tom pads

from the packing case, insert them into drum

stand as shown in the figure and tighten the

T-screw.

Take out the cymbal poles from the packing

case, insert them into pad hole as shown in the

figure and tighten the T-screw.

Assemble Crash cymbals as shown in the

figure and tighten the T-screw. 5

Assembly Instruction

Assemble Hi-Hat cymbal as shown in the figure and

tighten the T-screw.

Take out Snare pole from the packing case,

insert it into drum stand as shown in the figure

and tighten the T-screw. Take out Snare pad from the packing case,

insert it into Snare pole as shown in the

figure and tighten the T-screw.

As shown in the figure,electronic drum

installation is completed. 6

Assembly Instruction

Hi-Hat Foot Controller

---It can produce hi-hat closed sound if you hit hi-hat when pressing foot controller. ---It can produce hi-hat open sound if you hit hi-hat without pressing foot controller. ---Press foot controller directly to produce hi-hat pedal sound. ---The hi-hat tone changes smoothly from open to closed in response to press the pedal while hitting the hi-hat.

7

Connect Connecting the Power Supply

Make sure the power is switch OFF and connect the power adaptor to the DC 9V jack on the rear panel.

Connecting a CD Player, etc. (AUX In jack)

AC POWER

The audio output from a CD player connected to the AUX IN jack on the rear panel can be mixed with the sound of the drum brain. This function is convenient when you want to play along with a favourite song. The volume of the external signal is adjusted with the MASTER VOLUME knob.

CD player

AUX IN

USB MIDI

Connect PC or other USB host devices that support USB audio with a standard USB cable. For devices with USB cable, after the driver is installed and initialization is finished, you can choose USB audio device in the device menu of the software to transfer midi data.

Connecting Headphone The headphone can be connected to the electronic drum. The headphone jack is located on the front of the module. Use the PHONE VOLUME knob to adjust the headphone volume.

8

Start to Play the Drum

Switch the Power On

After confirming that each of the devices, pads, external devices, etc. are all properly connected, turn the power on. The drum module is ready to operate when the display shown below, for selecting the drum kit.

POWER ON OFF

Set the Master Volume MASTER VOLUME

Use the [MASTER VOLUME] knob to adjust the main volume MIN MAX

Select Drum Kits

Press [KIT] button, The current kit number appears. you can use the [+/-] button to select kits that you want.range:001-010,USER

KIT

[KIT] Button

Press [KIT] button and press [+] or [-] button to adjust the Volume of pads.range:000-127. KIT

- 9

Start to Play the Drum 1. Selecting Voice Press [KIT] button and [REC/PLAY] button,then hit the pad , use [+] [-] to select the Voice .

For example:to select TOM1 voice. Press [KIT] button and [REC/PLAY] button,LED displays current drum number . then hit the TOM1 LED displays t1 ,then LED displays TOM1 instrment .

hit the pad go on or use [+] [-] to select the Voice.In this mode you also can press [CLICK] button to listen to the voice, press [REC/PLAY] button to Deposited in user kit. Press the other button to exit the voice.

[CLICK] Button

Press [CLICK] button to turn on or turn off metronome.

a. Click Type Press [CLICK] button 2 seconds to enter the metronome type choice,use [+] [-] to select click type: 1/4, 2/4, 3/4, 4/4, 6/4, 3/8, 6/8, 12/8. default: 4/4

10

Start to Play the Drum b. Click Sound CLICK on, press[click] button and use [+] or [-] button to select click sound.

default: 001-003.

+ c. Click Volume CLICK off, press [CLICK] button and use [+]or[-]button to select click volume,range:000-032.

+ [REC/PLAY] Button

a. Recording Press [REC/PLAY] button 2 seconds,begin recording after four Metronome noise. b. Playing Record

Press [REC/PLAY] button , it will Playing Record. Press [REC/PLAY] button again, to stop play.

11

Start to Play the Drum

[SONG] Button

Your drum provides 10 preset songs and 1 Demo. Press [SONG] and [KIT] button to start or stop the song.

a.Drum On/Off In [SONG] mode, press [SONG] button 2 seconds, LED displays oN or oFF

On------turn on the percussion track of the song. Off------turn off the percussion track of the song.

b.Select the songs Press [SONG] button,then use [+] or [-] to select 10 songs and 1 demo.

c.Song volume In [SONG] mode, press [SONG] button and use [+] or [-] to adjust the song volume. Range:000-032.

- 12

Start to Play the Drum [TEMPO/TAP] Button

Tempo function, you can adjust tempo by using [TEMPO/TAP] button.

Press [TEMPO/TAP] button ,LED displays current tempo, use [+] or [-] button to adjust tempo value. Range: 020-240

Press [TEMPO/TAP] button 2 seconds to enter the TAP mode , LED displays will flash , Tap on the pad 4 times to change the tempo also.

+ 13

Factory Set Turn off the power.

Hold down [+] and [-] buttons, then turn the power on, it can restore all internal settings to

factory set.

- + a.Reseting Turn off the power. Hold down [KIT] buttons, then turn the power on to enter setup mode:

Press [TEMPO/TAP] button ,use[+]or [-]button to set sensitivity. range 001-008 Press [KIT] button ,use[+]or [-]button to set threshold. range 000-050 Press [SONG] button ,use[+]or [-]button to set velocity curve. There are four velocity curves from which to choose Normal(nor), Dynamic(dyn), EASY(ESy), and Fixed (fId). Press [CLICK] button ,use[+]or [-]button to set XTALK . range 000-080 Press [REC/PLAY] button to save above settings. Once turn off the power, it will be not saved.

14

Drum Kits List Kits No Kits name

Kits1 Acoustic_kit_1

Kits2 Acoustic_kit_2

Kits3 Room_kit NL

Kits4 Rock_kit

Kits5 Dance_club_kit

Kits6 Jazz_kit

Kits7 Electronic_kit

Kits8 Analog_kit

Kits9 Latin_kit

Kits10 Modern R&B

Kits11 User 15

Voice List Group 1: Kick Drums

Group 2: Snare Drums

Group 3: Toms

16

Voice List

Group 5: Hi-hats

Group 4: Cymbals

17

Style List

Style No Style name

01 Rock Shuffle

02 Surf Pop

03 Techno

04 60's Rock

05 Hard Rock

06 Pop Bossa

07 80's Rock

08 16 Beat

09 Pop Shuffle

10 Guitar Pop

18

MIDI Implementation Chart Function Basic Default Channel Changed Mode Default

Messages Altered

Note Number True voice Velocity Note ON

Note OFF Aftertouch Pitch Bend Control Change 0, 32

1 5 6 7 10 11 64 65 66 67 80, 81 91, 93 100,101 121

Transmitted Recognized 1-16 1-16 1-16 each 1-16 each Mode 3 Mode 3 X X

* X 0~127 0~127

* 0~127 O 99H,v=1~127 O 9nH,v=1~127 O 89H,v=0 O 8nH,v=0 or 8nH X X X O X X X O X O X O X O X O X O X O X O X O X O X O X O X O (*1) X O

Remarks

Memorized

Bank Select Modulation Portamento time Data Entry Volume Pan Expression Sustain Portamento Sostenuto Soft pedal DSP TYPE DSP DEPTH RPN LSB,MSB Reset all Controllers

Program Change True number System Exclusive System Song Pos Common Song Sel

Tune Aux Local on/off Messages All Notes Off

Active Sense Reset

O 0-10 O 0-127 0-127

X X X X X X X X X X O O X O X O

All Notes Off is sent as All Sound Off (CC# 120)

Mode1:OMNI ON, POLY Mode2:OMNI ON, MONO O: Yes Mode3:OMNI OFF, POLY Mode4:OMNI OFF, MONO X: NO

*1: Registered parameter number: #0: Pitch sensitivity #1: Fine tuning #2: Coarse tuning

19

Specifications Drum Pads: 1 Snare , 3 TOM Pads, 2 Cymbal Pads,

1 Hi-Hat, 1 Hi-Hat Control, 1 Bass Drum Display: Multi-Function LED Display. Polyphony: 32 Notes Max Voice Control: 173 Percussion Voices Drum Sets: 10 preset drum kits and 1 user drum kit Styles: 10 Styles Pad Control: Sensitivity; Threshold ;Velocity Curve;XTALK Demo: 1 Song Song recording: Real-time Record and Playback. Others: Tap, Click Level, Click Sound, Click Tempo,

Metronome (1/4, 2/4, 3/4, 4/4, 6/4, 3/8, 6/8, 12/8)

Interface: DC 9V Power Socket, PHONES, USB , CONNECT

TO BASE, RIDE, CRASH, HI-HAT, SNARE,

AUX IN. 10505774V1.0

20