Electric Height Adjustable Standing Gaming Desk

When operating any electric device, basic safety precautions should always be followed, Read all instructions before using your desk.FAILURE TO COMPLY WITH OR OBSERVE ALL INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.DANGER! To reduce the risk of electric shock, always unplug this device from the electrical outlet before cleaning or putting on or taking off parts.

Keep children away from the electric height-adjustable desk control units and keypads. Use this desk only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Keep the desk close to the power socket/outlet to be easily accessible. Keep all electrical components away from liquids. Keep the cords away from heated surfaces. Never operate this desk if it (1) has a damaged cord or plug, (2) is not working properly, (3) has been dropped or damaged, or (4) has been dropped into water. Do not open any of the components (e.g.,legs, control box or keypad) Contact Manufacturer for support and repairs. Do not insert anything into any seam or opening, this will damage the product. Do not operate this electrical product where aerosol (spray) products are being used or where oxygen is being administered. Do not use outdoors. Ensure there are no obstacles around or under your desk before use to prevent crushing or trapping people or property. Check the length of power cords for any electric devices placed on the desk before adjusting your desks height. Monitors, computer towers, speakers and other device cords may be pulled off or damaged if the cords are too short. Keep hands and fingers clear of areas where they may get pinched by the mechanism. Please ensure this manual is available to any user, installer, or support personnel that operates this product.

MAKE SURE NO OBSTACLES ARE IN THE DESK’S PATH AND ALL CORDS ARE OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY WITH OR OBSERVEALL ASSEMBLY, SAFETY, OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.

WARNING! To reduce the risk of burns, fire, electric shock or injury:

1. SAFETY AND WARNINGS

USE & LIABILITY• This height-adjustable desk has an electric motor and is designed for use in dry working conditions only. • The desk height can be positioned at the most ergonomically suitable height for the user. These desks are designed only for the purposes included in this manual. • The desk should not be used in environments with high humidity or dampness, as this will damage the product. Any other use is at user’s own risk.• Do not crawl between or lie under the desk frame. Do not sit or stand on the desk frame.• Children should never use the desk unless they are supervised by adults.

LIABILITY: This Eureka Ergonomic product is backed by a Three-Year Limited Warranty and a 30-day Risk-Free Purchase Guarantee. If it does not work the way we promised, we'll make it right. Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk frame other than that which is described in this operation manual.

Philips screwdriver and/or power drill Tape measure

TOOLS REQUIRED

customerservice@eurekaergonomic.com

844-416-2090

www.eurekaergonomic.com

844-416-2090

PARTS LIST & EXPLODED VIEW

x 1

x 1

x 1 x 1

x 1 x 2 x 2 x 1 x 1x 2

x 2

x 4 x 15

x 1

x 3

x 8

x 2 x 2 x 4

x 2

x 14

M6*20 M6*12M4*10 M4*16

Desktop Desk base Motor chamber

x 4

Fixed part Crossbar end Sliding rail Storage Box

Control box Hand Controller Storage box buckleCover rin Protective ring Magnetic sheet Leveling stud

Power wire Adhesive cable clips

Allen Wrench Philips screwdriver

CB D E F

I J K L M NH

O

Q R S T U V

P

GA

R

R

S

S

T

T

D

N

J

G

K

L

M

C

Q

B

S

S

S

EF

I

S

A

1.1

1.2

x 4N

1.1. Attach the leveling stud to the bottom of desk base.

1.2. Use a Phillips screwdriver to loosen the M4*10 screws of fixing plate that are affixed to the left/right of the motor chambers (4 PCS for left and right sides)

M4*10

2.1

2.2

x 8Q

2.2. Attach each desk base to the motor chamber using 8 x (M6*20) screws.

2.1. Put the covering plate on outer tubes of the motor chamber (both left and right).

3.1

x 6T

EF

E

3.2

3.2. Use six (M6*12) screws to connect the crossbar ends to the sliding rail, paying attention to the two screw holes in the base plate.

M8*16

3.1. Loosen four screws(M8*16) on the left/right of the motor chamber.

4.2

x 8T

4.3

M8*16

4.3. Tighten down the 4 screws you loosened in Fig. 3.1.

4.1

4.1. Lift the plastic cover on the motor chamber, and then buckle the fixed connection slot in the middle.

4.2. Secure the Crossbar ends to the motor chambers using 8x (M6*12) screws.

5.

Install four Protective ringsAttach 2PCS storage box clips left/right to crossbar end.

L

x 4

K

With an assistant,turn the desk base over so that the crossbar is in the upright position.

6.1

6.2

T

x 1

6.2. Install the control box in the crossbar and using an M6*12 screw, secure the control box on the left.

6.1. Attach the storage box to the storage box clips.

7.

Power wire

Motor wire

Motor wire

Hand controller wire

8.1

x 4R

1 2

3

2

8.2. Tighten the desktop and decorative fixed assembly left/right with four screws (M4*16). Align to the holes provided in the desktop.

8.1. Use four screws(M4*10) to tighten the motor chamber left/right and the decoration fixed assembly.

8.2

x 4S

9.

Once you have completed installation, connect the power supply to wall power and raisethe table to its maximum height and proceed to the following steps.

9.1. Use ten screws(M4*16) to lock the decorative fixed assembly left/right,crossbar end, hand controller and desktop.9.2. Use adhesive cable clips to secure the wires.

Sx 10

P

3

2 7

1 8

5

10

6

4

9

10.

x 2M

Place the 2 included magnetic sheets (have the surface with 3MM glue facing up) on the magnet of the storage box, and then remove the sheet covering the glue on the surface. Then rotate the stor-age box up, and let the magnetic sheet stick to the desktop.

DESK PLACEMENT

Following desk assembly, adjust the Leveling studs or casters (sold separately) on the feet so that the desk is level and does not shift its position.

When moving the desk, if casters are not installed, use a two-person lift and lift the desk so that it canbe moved without dragging. Dragging the desk may cause the frame and screws to pull loose from thedesktop.

When moving the desk, DO NOT lift the desk by the desktop alone, or the frame, alone. Support both-the frame and the desktop equally. Favoring one over the other can stress the fasteners connecting the desk frame to the desktop. Lower the desk completely and lift the desk by grasping the frame.

Choose a placement for the desk that’s a safe distance from window frames, radiators, furniture, etc, so that people do not get stuck or trapped by the desk.

Check cord clearance, so that they don’t get jammed. Then connect the desk to the 120v outlet and thedesk is ready for use.

Do not place any objects underneath the desk that are taller than 20’’.

MAX 330 LB.

INTELLIGENT HEIGHT MEMORY SETTINGS

TECHNICAL SPECIFICATIONS

Height Range 28 3/4”- 46 7/8”Overall Dimension 57 13/16” * 27 9/16” * 28 3/4”Travel Speed 0.79” per secondWeight Capacity 330 lbsWarranty 3 yearDuty Cycle 10%, Max 4 Memory presets Soft Start/Stop Adjustable leveling studs

customerservice@eurekaergonomic.com

844-416-2090

www.eurekaergonomic.com

For the latest User Installation Guide ， please visit: www.eurekaergonomic.com

1.Desktop height memory position settingRun mode, by pressing the up / down button to adjust the desktop to the appropriate height,And then press M and 1/2/3/4 of any one of them for 2 seconds, you can remember to save the desktop height.Canremember a total of four desktop height.For example: set the 3-key memory desktop height of 105, the current height of 90, press the key to run the desktop to 105, and then press the M +3 key, 2 seconds after the controller will flash the number 105, that memory is successful.

2.Desktop height memory location queryIn the run mode, press any of the 1/2/3/4 keys to Flash the height of the key memory.Press this key again for a long time to adjust to the desktop height of the key memory.

3.Initial use and restore factory settingsPress the down button to let the height drop to the lowest point, again press the down button for 3 seconds, when the display appears "- - -", the release of the key, the adjustable table will automatically run up and down to learn, until after completion , Restore the factory settings to complete, can be used normally.