EcoProof Pull Off Test
-
Upload
centaury2013 -
Category
Documents
-
view
220 -
download
0
Transcript of EcoProof Pull Off Test
-
8/13/2019 EcoProof Pull Off Test
1/15
Place your message here. For maximum impact, use two or three sentences.
Ecoproofat
Dene HouseNorth RoadKirkburton
Huddersfield
HD8 0RW
PULL OFFTEST
REPORT
REF: FC/11/3770
July 2011
SUPERFLAT FLOORTECHNOLOGY
DESIGN
SURVEYING
MEASUREMENT
-
8/13/2019 EcoProof Pull Off Test
2/15
Page 1
Page 2
Page 3
Page 5 Photographs of samples
Page 11
Page 12
FACE Consultants Pull Off Test Report
Contract specific details
Conclusion
FC/11/3770 - Table of contents
End of report
Description of works
Summary of results
-
8/13/2019 EcoProof Pull Off Test
3/15
Unknown
Unknown
Araldite RapidAdhesive Used:
07/07/2011 Dollys attached 1100 hrs08/07/2011 Pull Off Tests 1300 - 14.30 hrs
Name of Product : Ecoproof
BS EN 1542:1999
Test Date(s):
European/British Standard:
Pull Off TestMethod The maximum load at failure was recorded using an
Adhesion Tester and the type of failure noted for each
test.
Density of Each Test Sample:
Age of Screed Material:
Date and Time of Preparationof Samples for Test:
Test Location:
Name of Manufacturer:
Laboratory Preparing
Sample:
Huddersfield
Ecoproof Ltd
Date of Supply of Product : 29/06/2011 1715hrs
HD8 0RW
Ecoproof Ltd
Dene House
North Road
kirkburton
To conduct 5 Pull Off tests (3 needed) at our premises
on samples provided.
Contract Details
Appointed by:
Brief:
Luke Hutchinson
Site Address:
As above
08/07/2011
Laboratory
FC/11/3770 Page 1
-
8/13/2019 EcoProof Pull Off Test
4/15
Building conditions - Complete
Floor conditions - Not applicable
Weather Conditions - Good
Environmental Conditions:
The load is applied using an Adhesion tester pulling the
dolly from the surface under test. The maximum load atfailure is then recorded by the use of an analogue
gauge.
Test locations are cored to a depth of (15+/-5) mm.
For each test location a steel dolly of 50 mm diameter is
fixed to the sample surface using adhesive. After the
adhesive is set, typically 24 hours, the pull off test is
performed as follows.
Lighting Conditions - Good
A load frame is attached to the dolly via a threaded stud
in order that the load can be exerted at right angles to
the surface under test.
Elcometer 106 Scale 6 Adhesion Tester
Details:
Description of Works
Pull Off Test Equipment:
FC/11/3770 Page 2
-
8/13/2019 EcoProof Pull Off Test
5/15
Dene HouseNorth Roadkirkburton
HuddersfieldHD8 0RW
Summary of Results
Ecoproof
at
FC/11/3770 Page 3
-
8/13/2019 EcoProof Pull Off Test
6/15
Stress at Failure(N/mm
2)
0.5
5 1.5
Test Number Type of Failure
2 3.5 10% C & 90% B/C
1 85% Y/Z & 15% C
4 3.5 No Failure
3 3.5 15% C & 85% B/C
100% Y
FC/11/3770 Page 4
-
8/13/2019 EcoProof Pull Off Test
7/15
Photographs of Samples
Ecoproof
at
Dene HouseNorth Roadkirkburton
HuddersfieldHD8 0RW
FC/11/3770 Page 5
-
8/13/2019 EcoProof Pull Off Test
8/15FC/11/3770 Page 6
-
8/13/2019 EcoProof Pull Off Test
9/15FC/11/3770 Page 7
-
8/13/2019 EcoProof Pull Off Test
10/15FC/11/3770 Page 8
-
8/13/2019 EcoProof Pull Off Test
11/15FC/11/3770 Page 9
-
8/13/2019 EcoProof Pull Off Test
12/15FC/11/3770 Page 10
-
8/13/2019 EcoProof Pull Off Test
13/15
Test Number 3
Test Number 4
Test Number 5
At 1.5 N/mm2 there was 100% cohesion failure in the adhesive layer.
Report Compiled By:
Signed:
Date:
This report should not be reproduced except in full
At 3.5 N/mm2 there was 10% cohesion failure in the second layer and 90% adhesion
failure between the first and second layer
At 3.5N/mm2 there was 15% cohesion failure in the second layer and 85% adhesion
failure between the first and second layer
It should be noted however that the material was stretching.
At 3.5 N/mm2 there was still no adhesion failure but material was stretched to Maximum
Although it is clear that the material has good adhesion properties, due to the elastic
nature of the material we feel that it is not appropriate to give a mean tensile bond
strength from this form of testing.
It should be noted however that the material was stretching.
Conclusion
Test Number 2
Test Number 1
At 0.5 N/mm2 there was 85% adhesion failure between the adhesive layer and the dolly
and 15% cohesion failure in the second layer.
For and on behalf of Face Consultants Ltd.
14/07/2011
Duane R Scarfe (Operations Manager)
FC/11/3770 Page 11
-
8/13/2019 EcoProof Pull Off Test
14/15
END OF REPORT
FC/11/3770 Page 12
-
8/13/2019 EcoProof Pull Off Test
15/15