Dye test--sample taken from cannon ball flower (Cauroupita guianensis)
Dye and Pry Sample Report
-
Upload
takahiko-otowa -
Category
Documents
-
view
245 -
download
4
Transcript of Dye and Pry Sample Report
![Page 1: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/1.jpg)
TEST REPORTDYE AND PRY EVALUATION
Prepared for:
Prepared by:BEST, Inc.
3603 Edison PlaceRolling Meadows, IL 60008
Best Job NumberDate Testing CompletedSamples Submitted 10 PCBs
![Page 2: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/2.jpg)
Requested ServicesBEST, Inc. was asked to perform “dye and pry” analysis on the BGA devices of ten assemblies. The PWAs were visually and x-ray inspected. There were no abnormalities noted from the visual inspection. The x-ray inspection indicated some voiding of the TI BGA.
Dye and Pry ProcessThe procedure for this analysis includes immersing the subject device in a red dye under a vaccuum. The volitile components of the dye are then driven off by baking. The device is then pryed off the board. If there were any cracks or other types of solder interconnect failures, the areas will exhibit red dye penetration.
ResultsThere was no evidence of any dye penetration at the interconnect between the ball and the pad on all of the BGAs that were processed.
What was seen was a great deal of solder voiding of the TI device at the solder ball to BGA interface. The amount of solder voiding present on the TI BGAs is enough to present a high risk of failure. The failure of the solder interconnect will probably occur after thermal cycling or mechanical stresses. The solder voids are a defect in accordance with IPC-A-610 revision D, class 2 (paragraph 8.2.12.4).
RecommendationThe root cause of the solder voiding has to be identified. This may be caused by the thermal profile needing adjustment, or from the use of different alloys. Further research is necessary.
![Page 3: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/3.jpg)
Illustration 1: Serial #1210, Board, TI BGA, solder voids (light spots in solder balls)
![Page 4: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/4.jpg)
Illustration 2: Serial #1210, Board, TI BGA, solder voids (light spots in solder balls)
![Page 5: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/5.jpg)
Illustration 3: Serial #0216, Board, TI BGA, no dye penetration
![Page 6: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/6.jpg)
Illustration 4: Serial #0362, Board, TI BGA, solder voids (on top of solder ball)
![Page 7: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/7.jpg)
Illustration 5: Serial #0362, BGA, TI BGA, solder voids
![Page 8: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/8.jpg)
Illustration 6: Serial #0362, BGA, TI BGA, solder voids (100X magnification)
![Page 9: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/9.jpg)
Illustration 7: Serial #1262, Board, Samsung BGA, no observed problems
![Page 10: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/10.jpg)
Illustration 8: Serial #1262, Board, Samsung BGA, no observed problems (50X magnification)
![Page 11: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/11.jpg)
Illustration 9: Serial #1262, BGA, Samsung BGA, no observed problems
![Page 12: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/12.jpg)
Illustration 10: Serial #1262, BGA, Samsung BGA, pads ripped from board
![Page 13: Dye and Pry Sample Report](https://reader031.fdocuments.net/reader031/viewer/2022012314/547f1c5ab4af9fc3158b5930/html5/thumbnails/13.jpg)
Tested by: ____________________________ Date: ______________Hung HoangOperations Supervisor
Approved by: ____________________________ Date: ______________Bob WettermannPresident