DXC-390 / DXC-990 Pan Tilt Solution Sales Manual 8/20/2001 Sony Electronics Inc Visual Imaging...

DXC-390 / DXC-990Pan Tilt Solution

Sales Manual 8/20/2001

Sony Electronics IncVisual Imaging Products

Powered by AMX (Panja)

Our ProspectiveOur Prospective

SONY will provide total solution for Remote camera systemDXC-390 and 990 camerasPan/Tilt head powered by AMXController with CCU function powered by AMX

SONY dealers can sell the system with SONY camerasEasy to make a P/O for dealersTo beat Panasonic AWE series with P/T system

Working with AMXAMX is a great touch panel controller companyThey can customize control software locally

It is impossible for Panasonic

Remote camera system

House of worship HOT Sports shooting Web-casting HOT Distance Learning Board Room Production Videoconference

Target ApplicationTarget Application

Controls up to 6 cameras incl. DXC-390 / 990Color video 6 inches LCD monitor

Can watch video on the monitor

$9520 all set except Camera and lensHigh Speed / Quiet System

45 degree / sec Faster than competitors

High Accuracy5 arc minutes More accurate

Full Remote ControlAbility to control all camera functions by touch screen

Pan / Tilt and Controller SystemPan / Tilt and Controller System

By AMX / Panja


Comparison ChartComparison ChartSONY / Panja Panasonic Fujinon Pro Four

Model Positrack PT10 AW PH300A CPT-1A-10D 1000 RP

Pan/Tilt range(degree)Pan/Tilt speedAccuracy

359 Pan 359 Tilt

45 degree /secLess than +-5 arc

300 Pan 190 Tilt

25 Pan 20 Tilt+-5

300 Pan 190 Tilt

15 degree / sec+-10

350 Pan 180 Tilt

15 Pan 30 Tilt+-20

Controller capablenumber of cameraLoad capacity

Servo systemColor LCDpreviewmonitor

Up to 6 cameras

10lbs

Digital servoYes

Up to 5 cameras

8.8Lbs

AnalogNo

Up to 4 cameras

8.8Lbs

AnalogNo

7.5W

15lbs

AnalogNo

Camera and lenscontrol

Position Preset

Full remote forlens and camera

24 preset for eachcamera

Requiresseparate CCU

10 preset


8 preset


16 preset

Controller design Ergonomic userfriendly design

Outdated Outdated Outdated

Lens support Canon / FujinonFull support

Limited support Only Fujinon Limited support

List price $9520 $11606 $13680 $10600

PVMMonitorCCMC-12P05/10/25/US

Camera adapterDXC-390/990

Y/C or VBS

Single DXC-390 / 990 under 25mSingle DXC-390 / 990 under 25m

VBS

PT head

Genlock

ControllerMaster controller

CCXC-9DB/US (5m) RGB and VBSCCMC-9DS/US (5m) RGB and Y/C

AMX single head systemPT10-PLV

$9520

Power

Power

AXB-PT10

PS6.5

PS2.8

AXB-EM232

AXP-PLV

AMX Package

CMA-D2

PVMMonitorCMA-D3

Cable extension adapterDXC-390/990

Y/C VBS,RGB and (Component by 990)

Single DXC-390 / 990 under 100mSingle DXC-390 / 990 under 100m

VBS

PT head

Genlock


AMX single head systemPT10-PLV

$9520

P.S

P.S

CCZ-Axx/us cable

2/5/10/25/50/100m

CCM3MZ

AMX Package

PVMMonitorCCMC-12P05/10/25/US

Camera AdapterDXC-390/990

Y/C or VBS

Dual DXC-390 / 990 under 25mDual DXC-390 / 990 under 25m

VBS

PT head

Genlock


CCXC-9DBUS (5m) RGB, VBS and (Component by 990) CCMC-9DSUS (5m) RGB, Y/C and (Component by 990)

AMX dual head systemPT10-PLV + PT10-ADD

$9520+$3735xNexcept switcher

DXC-390/990

PT head

SwitcherWe can supply only 2x1 switcher PT10-PRV $700

P.S

P.S

CMA-D2

CMA-D2

PVMMonitorCMA-D3


Y/C VBS,RGB (Component by 990)

Dual DXC-390 / 990 under 100mDual DXC-390 / 990 under 100m

VBS

PT head

Genlock

Controller

AMX dual head systemPT10-PLV + PT10-ADD + PT10-PRV

$9520+$3735+$700

DXC-390/990

PT head

Switcher

CCZ-Axx/us cable

2/5/10/25/50/100m

CCM3MZ

PT10-PRV

P.S

P.S

P.S

Master controller

CMA-D3

PVMMonitorCMA-D2

Camera adapterDXC-390/990

Y/C VBS

3 to 6 cameras of DXC-390 / 990 under 25m3 to 6 cameras of DXC-390 / 990 under 25m

VBS

PT head

Genlock

Controller

AMX Multi head systemPT10-PLV3PLUS + PT10-ADD

$10655+$3735xNExcept switcher

CMA-D2

DXC-390/990

PT head

Switcher

2/5/10/25m

CMA-D2

CMA-D2

We recommend Extron SW6CVMX

CCMC12PXXUS

P.S

P.S

P.S Axcent3

PVMMonitorCMA-D3


Y/C VBS,RGB

Up to 6 cameras of DXC-390 / 990 under 100mUp to 6 cameras of DXC-390 / 990 under 100m3 to 6 cameras with CMA-D33 to 6 cameras with CMA-D3

VBS

PT head

Genlock

ControllerAxcent3

AMX Multi head systemPT10-PLV3PLUS + PT10-ADD

$10655+$3735xNExcept switcher

CMA-D3

DXC-390/990

PT head

Switcher

CCZ-A cable

2/5/10/25/50/100m

CCM3MZ

CMA-D3

CMA-D3

We recommend Extron SW6CVMXP.S

P.S

P.S

AMX Packages and accessoriesPackagesPT10PLV Single head system $9520 List Basic Kit

1 P/T head, cables, 1 Controller, 2 AC adapter, 1 System Controller

PT10PLV3PLUS for 3 or more cameras $10655 List1 P/T head, cables, 1 Controller, 2 AC adapter ,1 system controller with 6 RS232C port

AccessoriesPT10ADD Additional P/T head $3735 ListPT10PRV 2x1 switcher $700 ListACRK Accessory Rack Mount Kit $60 ListWMCAM Wall & Ceiling Mount kit $235 ListPMCAM Pedestal Mount Kit $200 ListTMCAM Tri-Pod adapter $45 List

Sony cameras and accessoriesSony cameras and accessories

Camera selectionDXC-390 1/3 inch C mount $2,995DXC-990 1/2 inch Bayonet mount $4,200

Lens selectionDXC3902 cable version

T14X55DA58/F 14x by Fujinon $2,550 ListT10X65SSB/SC 10x by Canon $1,960 List

*Please do not recommend VCL614WEA and 610WEA for AMX system.

Sony cameras and accessoriesSony cameras and accessories

Lens selection

DXC990Single hot shoe

YH18x67KTSA single hot shoe lens by Canon 18x zoom $4,770 ListYH14X73 KTSA single hot shoe lens by Canon 14x zoom $3,720 ListS14x73BWMDD8 single hot shoe lens by Fujinon 14x zoom $3,580 ListYH12X4.8 KTSA Wide Angle Lens by Canon 12X zoom $6,540 List

*Please do not recommend Double Hot Shoe lenses for AMX system.Of course Double hot shoe works well with RM-C950.

Sony cameras and accessoriesSony cameras and accessoriesCamera AdapterCMA-D2 standard camera adapter up to 25m CMA-D3 cable extension adapter up to 100m

Requires CCMC-3MZ cable, and CCZA-XX cableDepends on extension length

*In the case of using CMAD3, you can take RGB, (Component by 990) , VBS and Y/C from rear panel of CMAD3.*In the case of using CMAD2, you can take ONLY Y/C and VBS from rear panel of CMAD2, and but you can take RGB, (Component by 990) and VBS and Y/C directly from rear panel of camera

CablesCMA-D2

CCMC12PXX/US cable

CMA-D3

CCMC-3MZ Junction cable

Package and accessories price for AMX systemPackage and accessories price for AMX systemModel Description Sony MSRP

PT10-PLV Single Camera Pan/Tilt System 9,520.00$ System includes:

1 - AXP-PLV PosiTrack Pilot Video Panel1 - AXB-EM232 Enhanced Master/RS-232 Controller1 - PS2.8 12 VDC, 2.8 A Power Supply (regulated, 110 VAC input)1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to Phoenix)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to 9-pin D-sub1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable

PT10-PLV3plus Multi-Camera Pan/Tilt Systems for CMA-D3 Operation $ 10,655.00$ 1 - AXP-PLV PosiTrack Pilot Video Panel1 - AXCENT3 Integrated Controller1 - PS2.8 12 VDC, 2.8 A Power Supply (regulated, 110 VAC input)1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)6 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to 9-pin D-sub)1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable

PT10-ADD Additional Camera Pan/Tilt 3,735.00$ System includes:

1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to Phoenix)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to HD15)1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable

PT10-PRV Optional 2x1 Preview Switcher 700.00$ System includes:

1 - AV2SM Auto/Manual Video Switcher (2x1)1 - AXB-REL8 Relay Controller1 - CC-REL

Camera Control Optional ComponentsModel Description Sony MSRP

AC-RK Accessory Rack Kit (3 module capacity, single rack unit height) 60.00$ WM-CAM Wall or Ceiling Mount Adapter for AXB-PT10 235.00$ PM-CAM Pedestal Mount Adapter for AXB-PT10 200.00$ TM-CAM Tripod Mount Adapter for AXB-PT10 45.00$

Ordering Matrix chart 1Ordering Matrix chart 1

Qty Camera Package PT10-PLV PT10-ADD PT10-PLV3+ PT10-PRV1 DXC-390 or 990/CMA-D2 12 DXC-390 or 990/CMA-D2 1 1 Optional3 DXC-390 or 990/CMA-D2 2 1 Extron4 DXC-390 or 990/CMA-D2 3 1 Extron5 DXC-390 or 990/CMA-D2 4 1 Extron6 DXC-390 or 990/CMA-D2 5 1 Extron

1 DXC-390 or 990 /CMA-D3 12 DXC-390 or 990 /CMA-D3 1 1 Optional3 DXC-390 or 990 /CMA-D3 2 1 Extron4 DXC-390 or 990 /CMA-D3 3 1 Extron5 DXC-390 or 990 /CMA-D3 4 1 Extron6 DXC-390 or 990 /CMA-D3 5 1 Extron

Configurations AMX Components

*You can mix up to use DXC-390 and DXC-990

Ordering chart 2Ordering chart 2

Components Model Name PriceCamera DXC-390 $2,995Camera adapter CMA-D2 $252Lens 14x T14X55DA58/F $2,550AMX kit PT10-PLV $9,520Camera cable 5m CCMC-12P05/US $169Wall mount kit WMCAM $235

Total $15,721

One DXC390 standard ordering

Components Model Name PriceCamera DXC-990 $4,200Camera adapter CMA-D2 $252Lens 14x YH14X73KTSA $3,720AMX kit PT10-PLV $9,520Camera cable 5m CCMC-12P05/US $169Wall mount kit WMCAM $235

Total $18,096

One DXC990 standard ordering


Components Model Name PriceCamera DXC-390 x 2 $5,990Camera adapter CMA-D2 x 2 $504Lens 14x T14X55DA58/F x 2 $5,100AMX kit PT10-PLV $9,520Additional head PT10-ADD $3,735Camera cable 5m CCMC-12P05/US x2 $338Switcher PT10-PRV $700Wall mount kit WMCAM x 2 $470

Total $26,357

Two DXC390 standard ordering

Components Model Name PriceCamera DXC-990 x 2 $8,400Camera adapter CMA-D2 x 2 $504Lens 14x YH14X73KTSA x2 $7,440AMX kit PT10-PLV $9,520Additional head PT10-ADD $3,735Camera cable 5m CCMC-12P05/US x 2 $338Switcher PT10-PRV $700Wall mount kit WMCAM x 2 $470

Total $31,107

Two DXC990 standard ordering


Components Model Name PriceCamera DXC-390 x 3 $8,985Camera adapter CMA-D2 x 3 $756Lens 14x T14X55DA58/F x 3 $7,650AMX kit PT10-PLV3PLUS $10,655Additional head PT10-ADD x 2 $7,470Camera cable 5m CCMC-12P05/US x 3 $507Switcher by Extron SW6CVMX $695Wall mount kit WMCAM x 3 $705

Total $37,423

3 to 6 DXC390 standard ordering

Components Model Name PriceCamera DXC-990 x 3 $12,600Camera adapter CMA-D2 x 3 $756Lens 14x YH14X73KTSA x 3 $11,160AMX kit PT10-PLV3PLUS $10,655Additional head PT10-ADD x 2 $7,470Camera cable 5m CCMC-12P05/US x 3 $507Switcher by Extron SW6CVMX $695Wall mount kit WMCAM x 3 $705

Total $44,548

3 to 6 DXC990 standard ordering

*SONY does not sell Extron Switcher

*SONY does not sell Extron Switcher

*Costs $9,936 for each An additional camera

*Costs $12,311 for each

An additional camera


Components Model Name PriceCamera DXC-390 $2,995Camera adapter CMA-D3 $1,520Lens 14x T14X55DA58/F $2,550AMX kit PT10-PLV $9,520Camera cable 50m CCZA50US $1,315Junction cable CCZ3MZ $385Wall mount kit WMCAM $235

Total $18,520

One DXC390 with CMAD3 for cable extension ordering

Components Model Name PriceCamera DXC-990 $4,200Camera adapter CMA-D3 $252Lens 14x YH14X73KTSA $3,720AMX kit PT10-PLV $9,520Camera cable 50m CCZA50US $1,315Junction cable CCZ3MZ $385Wall mount kit WMCAM $235

Total $19,627

One DXC990 with CMAD3 for cable extension ordering

FAQ 1FAQ 1Can we use CMA-D3 for DXC950?

NOCan we use CCU-M5A for this system?

NOHow can we have field supports for the system?

AMX tech support can help you.1-800-932-6993

How can we get longer Axlink cables?Any AMX Dealers will support that.For example Liberty Wire & Cable 1-800-530-89981000' rolls or cut to lengths over 500‘ $0.265 per foot

How long can we extend Axlink cable?Up to 3000 feet including all cables

How can we get 6x1 capables switcher?We would recommend Extron one.

SW6CVMX 60-205-01 $695 list

FAQ 2FAQ 2•Troubleshooting TipsCommon Tech Support Issues (Pan/Tilt Head)Balancing of camera/lens assembly is critical! Improper balancing can cause tilt errors and lockup problems.

On error detection, pan/tilt movement stops (for safety) and will not move until power is cycled. Upon power cycle unit will attempt movement again until another error is detected.

The four slide switches next to the under the circular cover set the lens voltage control mode. All Sony approved lenses are Positional Servo style lenses so all four slide switches must all be set to the left (Auto Position), not to Manual.

The LENS POWER switch toggles +12VDC on pin 1 of the 15 pin D sub connector. All Sony approved lenses get power from the camera so set the LENS POWER switch to the CAM position. If the lens gets power from the camera AND you try to supply power from the PT10, damage may occur.

FAQ 3FAQ 3Lens

Many lenses are not connected to the 15 pin lens port at all and are actually controlled by the camera, which we control via RS232. In these cases the lens control problem is usually an RS232 communication issue between the PT10 and the camera. Check the RS232 cable and restart the Master (AXB-EM232 or Axcent3).

Setup

With multiple camera systems the PT10 Axlink DIP switches must be set to unique values. All AXB-PT10’s are factory set to device 90 which corresponds to camera 1 on the controller. Additional PT10’s should be set sequentially.

Axlink Device Camera Number

90 1

91 2

92 3

93 4

94 5

95 6

Use the DIPSwitch.exe program to reference the correct switch settings. Power must be cycled for changes to take effect.

FAQ 4FAQ 4Problem Possible Cause

No zoom/focus/iris (lens control) If using analog voltage lens control:

•Ensure LENS POWER switch is set to CAM•Ensure lens power switches are all set to the LEFT (Sony only ships Servo Positional style lenses with these systems)If using RS232 camera lens control:

•PT10 must be talking to camera for lens control to work.•Verify camera communication by pressing ‘BARS’ button on panel and looking for color bars from camera. Toggle on and off.•Cycle power on entire system to re-establish communication.•Upgrade to Master Axcess code version 1.56 or later with enhanced Sony communication reliability.•Verify AMX devices are set to 9600 baud.

•On the PT10 switch S2 should have all switches up (on) except switch 7 which should be down (off).•On the EM232 both interface switches (NOT the Program switch) should have all switches down (on) except switch 7 which should be up (off).•Verify DXC camera is set to 9600 baud.

FAQ 5FAQ 5No Focus or Sporadic Focus Movement

•The software version is incompatible with the version of Pilot controller in the system.•Serial numbers beginning with 563070 or 563080 must have a “P” version of software.•Serial numbers beginning with 563050 or 563060 must NOT have a “P” version.

No Pan/Tilt

•Verify Axlink device address (90 – 95)•Verify Axlink LED flashes on PT10

Multiple Heads Pan and Tilt at the Same Time

•Check for duplicate Axlink device ID’s on the PT10’s.

PT10 “Drifts” or Moves by Itself

•Joystick is not calibrated. Reboot the entire system and do not touch the joystick or control knobs during initialization (“Please Wait” screen).

Other issues can be resolved by calling the toll free AMX Technical Support hotline at 800-93AMX93 (800-932-6993).

Software UpgradeSoftware Upgrade

Other issues can be resolved by calling the toll free AMX Technical Support hotline at 800-93AMX93 (800-932-6993).

Software Upgrades AMX will continue to improve performance and features of the system and update in-house inventory. Upgrading your demo unit in the field is a simple procedure that you can perform yourself. Software upgrades are sent as a .zip file from AMX.1. Attach the 9 pin cable to the PC com port and the Master (Axcent3 or EM232).2. Verify all switches on the AXB-EM232 Program switch are down (cycle power if you change them).3. Unzip the files to a directory on your PC.4. Open a dos prompt and go to the directory you unzipped files to.5. type: tokenx /s 1 38400 where 1 is the com port number on the PC.6. Reboot the entire system when it's finished and you should see the new version number on the initial page. Firmware upgrades for the PT10 are also sent as a .zip file.1. Attach the 9 pin cable to the PC com port and the Master (Axcent3 or EM232).2. Unzip the files to a directory on your PC.3. Double click Softrom.exe to start the application.4. Press F1 to set the com port and baud rate. Select 38400 for the baud rate and select the appropriate com port. Press F10 to save settings.5. Press F5 to query on-line devices. This should cause some items to appear on the right side of the screen.6. Press Enter to highlight the firmware file on the left. Press Tab to toggle to the Device side of the screen.7. Locate the AXB-PT10 to be upgraded. It will have a number from 90-95 in the # column and $dc in the Typ column. Press enter to highlight the device.8. Press F4 to program the PT10 with the new firmware.9. When the upgrade is complete press F10 to exit the program.10. Reboot the entire AMX system.

AMX componentsAMX components

AXB-EM232 Enhanced Master ControllerFor 2 or less cameras

The AXB-EM232 Enhanced Master RS-232 Controller is a bus device that provides the features of a system master in a single compact enclosure. It can be used either as a stand-alone device or with other Panja bus devices. The AXB-EM232 runs complete AXCESS programs and allows control of AXlink components as well as control of up to two devices using RS-232 as a control protocol.

Features: Supports RS-232, RS-422, and RS-485 controlled devices, such as switchers and computer-based devices, as well as AXlink devices Supports hardware handshaking and the following asynchronous data communication standards: Baud rates 300; 600; 1,200; 2,400; 4,800; 9,600; 19,200; and 38,400 Data bits 7 or 8, Stop bits 1 or 2, Parity None, Odd, Even, Mark, or Space Includes a 12 VDC power supply Stores program commands in battery-protected memory


AXCENT3 Integrated ControllerFor 3 or more cameras

The AXCENT 3 Integrated AXCESS Controller is a multi-port Central Controllers that can be programmed to control RS-232/422/485, relay, IR/serial/data, and input/output devices.

Features 32 front panel status LEDs for AXlink bus operation, RS-232/422/485 (12 LEDs), relay (eight LEDs), IR/serial (six LEDs), and I/O control activity (six LEDs) Six RS-232/422/485 control ports with XON/XOFF LEDs (transmit on/transmit off), and CTS/RTS (clear to send/ready to send), 300–115,200 baud Six IR/serial/data control ports that support IR carrier speeds up to 1.14 MHz, and 1-way data, 300–38,400 baud (0–5 VDC only) Six-channel I/O port for contact closure, 0–5 VDC voltage sensing or inter-active power sensing for IR ports Eight-channel relay port Converts from Master (default) to server operation, allowing use of up to 18 Central Controllers in the same systemAllows system setup, status polling, and diagnostic operations locally, or with a modem, using the Windows-based OpenAXCESS Remote Setup Terminal program


The value of the AXB-PT10 PosiTrack 10 can be expressed in three terms—excellent-quality, extreme controllability, and low cost. Supporting camera loads of up to 10 lbs, PosiTrack’s innovative design fuses smooth, quiet motion analog motor drive with precision digital position sensing. Featuring a resolution of over 1 million steps, PosiTrack's digital encoders provide responsive speed control and pinpoint preset accuracy within ±5 arc minutes.

AXB-PT10 Pan/Tilt Head

Features: Supports camera loads of up to 10 pounds (13.6 kg), allows perfect adjustment of H/V center of gravity Integrates onboard control for camera pan/tilt, lens zoom/focus/iris, and RS-232 CCU operation Operates DC-drive lens directly, without need for outboard controllers Stores and recalls presets from internal non-volatile memory Installs upright or upside down (joystick control can be inverted) Limits pan and tilt range using soft stops, programmable on-the-fly from the PosiTrack Pilot Video touch panel Moves with analog DC motor control, positioning sensed via 1 million-step digital encoding Connects to the system via the four-wire AXlink control network over distances up to 3,000 feet using standard twisted-pair wire


Features Controls up to 6 PosiTrack 10 Pan/Tilt Heads with Sony DXC-390/DXC-990 cameras, up to 24 presets per camera 6" color-active LCD displays camera video with superimposed touch control graphics On-screen graphics control preset store/recall, camera, and system setup Side-screen buttons (12) instantly select cameras and access control menus Integrated 3-axis joystick controls pan, tilt, and zoom Proportional side-mount wheel controls focus and iris control

AXP-PLV PosiTrack Video Pilot Video Panel

AMX componentsAMX componentsPSN6.5 Power Supply The PSN6.5 supplies power to the AXB-PT10 Pan/Tilt Camera Head

Technical Specifications

DC Power: 12 VDC, 6.5 A output

AC Power: IEC AC cord input for 110/220, 50/60 Hz AC power

Dimensions: 1.5” x 5.5” x 6.4” (HWD) (38mm x 140mm x 164mm)

Weight:: 1.1 lbs. (495 g)

PS2.8 Power SupplyThe PS2.8 supplies power to the system controller and control panel

Technical SpecificationsDC Power: 12 VDC, 2.8 A output

AC Power: IEC AC cord input for 110/220, 50/60 Hz AC power

Dimensions: 5.5” x 3.0” x 1.8” (HWD) (140mm x 76mm x 45mm)

Weight:: 1.5 lbs. (681 g)


CC-CAM Connection CablesCC-CAM camera/lens cable connects AXB-PT10 RS-232 control to DXC-390/990 camera head. DB9 (PT10) to 8-pin Mini-DIN (DXC390/990 control input), length – 21 inchesCC-CAM camera/lens cable connects AXB-EM232 RS-232 control to CMA-D3 controllers. 4-pin captive wire Phoenix (EM232) to 8-pin Mini-DIN (CMA-D3), length – 10 feetCC-CAM camera/lens cable connects AXCENT3 RS-232 control to CMA-D3 controller. DB9 (AXCENT3) to 8-pin Mini-DIN (CMA-D3), length – 10 feet

PT10PRV Auto/Manual Video SwitcherFor 2 cameras

Switcher is a media interface device that you can set to automatically or manually switch between two audio and video input sources to one output display monitor. When the internal sync sensor detects a video signal, the AV2SM routes the incoming video and audio signals to the output display monitor connected to the front panel.

Features Two video and audio input source connectors and one output connector Quick connect BNC video connectors


The AXB-REL8 Relay Controller provides remote control for up to eight relay functions. Suitable for stand-alone or rack mount applications, the AXB-REL8 may be used with AXCESS or AXCENT systems via the four-wire AXlink data bus.

AXB-REL8 Relay ControllerComes with PT10PRV

DXC-390 / DXC-990 Pan Tilt Solution Sales Manual 8/20/2001 Sony Electronics Inc Visual Imaging...

Documents

Transcript of DXC-390 / DXC-990 Pan Tilt Solution Sales Manual 8/20/2001 Sony Electronics Inc Visual Imaging...