1

Quick Start

DSLAM5008/16/24 IP DSLAM

MAY 2010

V1.0

Shanghai sino-telecom Technology Co., Ltd.

2

Thanks for using the IP DSLAM from shanghai sino-telecom Technology

Co., Ltd. In order that you can use our IP DSLAM as soon as possible, this

guide will quickly introduce the states, installation, and commonly configuration

(WEB, CLI) of our device. The hardware installation section describes how to test before the installment and also the steps of installment; Common

configuration parameters section describes how to configure the device by

command-line Interface (CLI) mode and WEB mode.

Shanghai Sino-telecom Technology Co., Ltd. Add6th floor, Building 2, lane 115, NO.1276 Nanle Rd.songjiang District,

Shanghai, P.R.ChINA 201613

Tel+86-021-67755200/67755366/67755266 Fax+86-021-67755300 Sino-telecom Technology

www.sino-telecom.com

3

1 Hardware installation Equipment test: This section will instruct you to judge whether the IP

DSLAM is running normal or not and the fittings are all ready before you install

it.

Step 1

Please check the fittings after you open the box, the standard list shows as

follows. The figure is only for referring, the object is the standard. IP DSLAM 1pcs Power line 1pcs Console Cable 1pcs Installing Brackets 1pcs Cate Cable 5 1pcs Digital CD 1pcs Telco cable 1pcs Quick Start Guide 1pcs

Step 2

According to the POW request (AC220V/DC48V), you must connect anode and cathode according to the Power line from the box. Otherwise it will damage the IP DSLAM. Push the power on and check whether the device is running normal.

Type The status of lights when it is running normal

DSLAM5008DSLAM5008DSLAM5008DSLAM5008

1First all the lights full on, then the lights of DSL port(0-7) flashes regularly, DSLAM start normally, if the Ethernet port is connected to a router or a computer, ETH lights, it will cost about 1-2 minutes; 2when the DSLAM and Modem handshake normal, the lights of ports are always on;

DSLAM5016DSLAM5016DSLAM5016DSLAM5016

1 first all the lights full on , then just power light on, the other all lights destroy. finally the lights of DSL port(0-15) flashes regularly, DSLAM start normally, if the Ethernet port is connected to a router or a computer, ETH lights, it will cost about 1-2 minutes; 2when the DSLAM and Modem handshake normal, the lights of ports are always on;

DSLAM5024DSLAM5024DSLAM5024DSLAM5024 1 first all the lights full on , then just power light on, the other all lights destroy. finally the lights of DSL port(0-23) flashes regularly, DSLAM

4

After complete the testing ,you can install the DSLAM, the concrete

operations as follows:

Step 3

Connect the cables foundation the silk-screen on crust. Install the couple

ears on both sides of the device, then install the device in the rack. If there isnt

rack, you can also put the device to a desktop which is flat, balanced,

ventilation, clean and close to the power outlet.

Step 4

Equipment placement is completed, according to box screen; connect the

following cables, the specific operation requested in the following table and

control panel screen.

1to cable and on the associated equipment (computer configuration) phase; 2cable to connect to the PSTN interface, Bureau of the side, users connect to

the Line side interface, and also a cable hit by the corresponding patch panel on the order (line order form, see table);

3 connecting with the earth; 4the power cord into a power outlet;

start normally, if the Ethernet port is connected to a router or a computer, ETH lights, it will cost about 1-2 minutes; 2when the DSLAM and Modem handshake normal, the lights of ports are always on;

Equipment Type The interface description

DSLAM5008DSLAM5008DSLAM5008DSLAM5008

DSLAM CABLEDSLAM CABLEDSLAM CABLEDSLAM CABLE RJ21RJ21RJ21RJ21 connect the cable to the user side and the side of MDF Board

ON/OFFON/OFFON/OFFON/OFF 220V AC220V AC220V AC220V AC when the button is turned ON shows power-on, while the button is OFF, shows power-down

GNDGNDGNDGND the interface connect ground

DSLAM5016DSLAM5016DSLAM5016DSLAM5016 LineLineLineLine RJ21RJ21RJ21RJ21 connect the cable to the user side PSTNPSTNPSTNPSTN RJ21RJ21RJ21RJ21 connect the cable to the side of MDF Board

5

16 port 24 port

Voice port Color Line port Color 1 Red brown 1 White Blue 2 Red Ash 2 White Orange 3 Black Blue 3 White Green 4 Black Orange 4 White Brown 5 Black green 5 White ash 6 Black Brown 6 Red blue 7 Black Ash 7 Red orange 8 Yellow blue 8 Red Green

8 port

ON/OFFON/OFFON/OFFON/OFF 220V220V220V220V ACACACAC when the button is turned ON shows power-on, while the button is OFF, shows power-down

GNDGNDGNDGND the interface connect ground

DSLAM5024DSLAM5024DSLAM5024DSLAM5024

LINELINELINELINE RJ21RJ21RJ21RJ21 connect the cable to the user side PSTNPSTNPSTNPSTN RJ21RJ21RJ21RJ21 connect the cable to the side of MDF Board ON/OFFON/OFFON/OFFON/OFF 220V220V220V220V ACACACAC when the button is turned ON shows power-on,

while the button is OFF, shows power-down GNDGNDGNDGND the interface connect ground

PSTN/ LINE

Color PSTN/ LINE

Color

1 White Blue 13 Black green

2 White Orange 14 Black Brown 3 White Green 15 Black Ash 4 White Brown 16 Yellow blue

5 White ash

6 Red blue

7 Red orange

8 Red Green

9 Red brown

10 Red Ash

11 Black Blue

12 Black Orange

PSTN /LINE

Color PSTN /LINE

Color

1 White Blue 13 Black green

2 White Orange 14 Black Brown 3 White Green 15 Black Ash 4 White Brown 16 Yellow blue

5 White ash 17 Yellow Orange

6 Red blue 18 Yellow Green 7 Red orange 19 Yellow Brown

8 Red Green 20 Yellow Ash 9 Red brown 21 Purple Blue

10 Red Ash 22 Purple Orange 11 Black Blue 23 Purple Green 12 Black Orange 24 Purple Brown

6

Annex IP DSLAM user cable diagram

16,24 DSLAM port cable connection diagram users

8port DSLAM user cable connection diagram

2 Web Configuration This section introduces to you how to do some general use commands

for configurations about the DSLAM via WEB and CLI, includingEquipment loginModify IP addressLimit DSL training rateChange vpi/vciVLAN configurationSave configurationBackup / restore configurationFirmware upgradesRestore the default configurationCLI All operations must be saved after changed, otherwise the configurations after reboot will be

lost.

7

2.1 Login

After successful login, you can view all the equipment port status, A0 ~ A7

that DSL port 1 ~ 8, 16, 24 equipment and so on, that has been normal,

that is not connected then. Here in the WEB mode configuration of

equipment commonly used parameters.

2.2 LAN address changes

Click on the home page Access to view the LAN IP address of the interface

To change the current device IP addressplease chick to Edit Interface

8

Enter your need to set the IP address, click "Change", change has been

completed, please enter a new address into the WEB page.

2.2 Modify ADSL port up/downlink rate

Step 1 Click the need to modify the port number, must revise the port is

click A0 1

Step 2 Click the View advanced attributes... into the advanced

configuration options

9

Step 3 Access to advance configuration, the slider to the right side down,

to modify the rate of the region:

Modify the map data in the box, 512K was revised to: 512000,1 M

was revised to: 1024000,2 M modified as follows: 2048000, and

so on, n * 1024000 = n M speed, fast mode and interleave mode

rate need to be changed at the same time.

Step 4 Option to modify the above is completed, pull the slider to the

bottom, click the Apply button to modify the data entry into force,

and then save the configuration (see save the configuration steps).

10

Note: This page will refresh in 10 seconds, 10 seconds required to

modify and click apply, or can not be successfully modified,

proposed an amendment one by one.

2.3 Modify the VPI / VCI

According to equipment located VPI / VCI values changes, equipment

default VPI / VIC is 0 / 35, is the most widely used VPI / VCI value, if not

special needs, basically do not need to be modified.

Select the menu Configuration -> WAN connections into the WAN / ATM

interface port information.

Interface in the figure, click on Edit ... to enter the port parameter

modification interface, enter the WAN port editing interface, click on the menu

Edit Atm Channel, appeared to modify VPI / VCI value interface, as shown

below.

11

Would need to modify the values entered into the appropriate box inside.

Note: Modify the VPI / VCI value is required to send RX / TX of the VPI /

VCI also modify

2.5 VLAN Configuration

Click the left menu configuration bridge to page

Select vlan configuration

12

Step 1Click "create new vlan" fill in the actual situation based on your vlan name vlan ID, etc.

Step 2Chick OK back

Step 3This has just added vlan select Edit to configure according to your needs vlan

Modify the VLAN tagged ports under

Click Edit tagged ports under the Edit, Fill tagged need to configure

the port name

Modify the VLAN Untagged ports under

Chick Edit untagged ports under the Edit, fill untagged to configure

the port name

2.4 System Upgrade

Step 1 Click on the menu system -> firmware update, the right interface,

click "Browse."

13

Step 2 File select screen appears, find the path where the upgrade file,

select the file (eghttp-upload.img), and click Open.

Step 3 Back to Firmware Update interface, click the button Update, began

to transfer files to the device, and displays a progress bar, as shown

below

Note Upgrade 2-3 minutes after complete, please restart your devicePlease don't cut off power upgrade

Step 4 Progress bar to 100%, it will automatically switch to restart the

interface device, and prompt completion of documentation has been

updated, and then click Restart, wait for the device startup is

complete, the upgrade is complete.

2.5 Restore the default configuration device

Click on the menu system-->Restart Router later, the right to select

Reset to factory default settings click the Restart button to restart the device. Equipment startup is complete; configure all the back to the factory

configuration, IP address: 192.168.1.32, as illustrated

14

2.6 Restore / backup configuration files

Click the menu system -> Backup / Restore, click the Backup button on

the right, the device is currently running configuration saved to the computer.

Or click "Browse" button, select the saved configuration file on your computer,

click Restore, import equipment. Interface as shown below:

2.7 Save Configuration

Click on the menu Configuration -> Save, click Save to save the data

has been modified to the device.

Note: the end of all need to keep all operations, or equipment

configuration is missing after reboot.

15

3 Command configuration

There are two command-line login configurations, Telnet and Console,

Telnet mode with landing, to ensure that the computer IP address and

DSLAM address the same network segment.

Console login form by following these steps:

Step 1 With the serial line using random, computer serial port (RS232) to connect to the device Console port;

Step 2 Click computer menu start->process->Accessories->

Communication->HyperTerminal, open the HyperTerminal interface,

click Restore Defaults will restore the HyperTerminal configuration

parameters to the default configuration, as shown below

Step 3 Click OK, enter the device login screen, enter the user name: admin, password: admin, there "->" prompt, said the registry has been

16

logged to the device command line (CLI), you can configure the device through the command, the following is the command format.

3.1 View the IP address

Example: ip list interface

3.2 Modify the IP address

Example: IP address of the device change 10.10.10.1 255.25.25.0

ip set interface ipwan ipaddress 10.10.10.1 255.255.255.0

3.3 Rate changes

ExampleSet the downlink rate 2M, upstream rate of 1M port a0 set AtucChanConfInterleaveMaxTxRate 2048000

port a0 set AturChanConfInterleaveMaxTxRate 1024000

3.4 Modify VPI/VCI

Example: modify the A0 port VPI / VCI is 8 / 35

rfc1483 set transport wb0 vpi 8

rfc1483 set transport wb0 vci 35

3.5 Save/reboot

Save Configuration: system config save

Restart devicesystem restart

Restore the default configurationsystem config restore factory