Download Owners Manual Indian Cars Pdf Format Maruti ......Maruti Suzuki offers the Emission...

1

59K,76G,844-74E

TABLE OF CONTENTS 1MAINTENANCE SERVICE RECORD

2WARRANTY POLICY

3BEFORE DRIVING

4STEERING COLUMN CONTROLS

5INSTRUMENT PANEL

6OTHER CONTROLS AND EQUIPMENT

7OPERATING YOUR VEHICLE

8DRIVING TIPS AND SAFE DRIVING

9INSPECTION AND MAINTENANCE

10EMERGENCY SERVICE

11BODY WORK CARE

12GENERAL INFORMATION

13SPECIFICATION

2

59K,76G,844-74E

3

59K,76G,844-74E

FOREWORDThis manual is an essential part of yourvehicle and should be kept with the vehicleat all times. Please read this manualcarefully and review it from time to time. Itcontains important information onmaintenance. It is especially important thatthis manual remain with the vehicle at thetime of resale. The next owner will need thisinformation also.

You are invited to avail the three freeinspection services as described in thismanual. Three free inspection coupons areattached to this manual. Please show thismanual to your dealer when you take yourvehicle for any Service.

To prolong the life of your vehicle andreduce maintenance costs, the periodicmaintenance must be carried out accordingto the "PERIODIC MAINTENANCESCHEDULE" described in "INSPECTIONAND MAINTENANCE" section of thismanual. Periodic maintenance is essentialfor preventing trouble and accidents toensure your satisfaction and safety.

Daily Inspection and Care as per "DAILYINSPECTION CHECKLIST" described in the"INSPECTION AND MAINTENANCE"section of this Manual is essential forprolonging the operating life of the vehicleand for safe driving.

All information in this manual isbased on the latest productinformation available at the time ofpublication. Due to improvements orother changes, there may bediscrepancies between informationin this manual and your vehicle.MARUTI SUZUKI reserves the rightto make changes at any timewithout notice.This vehicle may not comply withstandards or regulations of othercountries. Before attempting toregister this vehicle in any othercountry, check all applicableregulations and make anynecessary modifications.

IMPORTANTWARNING/CAUTION/NOTEPlease read this manual and follow itsinstructions carefully. To emphasise specialinformation, the words WARNING,CAUTION, and NOTE have specialmeanings. Information following these signalwords should be carefully reviewed.

The personal safety of the driver,passengers, or bystanders may beinvolved. Disregarding this informationcould result in their injury or death.

These instructions point out specialservice procedures or precautionsthat must be followed to avoiddamaging the vehicle.

CAUTION

MARUTI SUZUKI INDIA LIMITED believesin conservation and protection of Earth'snatural resources.

To that end, we encourage every vehicleowner to recycle, trade in, or properlydispose of, as appropriate, used motor oil,coolant, and other fluids; batteries; andtyres.

MARUTI SUZUKI INDIA LIMITED

0-1

wwwww WARNING

NOTE :This provides special information to makemaintenance easier or important instructionsclearer.

4

59K,76G,844-74E

MODIFICATION WARNINGwwwww WARNING

Do not modify this vehicle. Modifica-tion could adversely affect safety,handling, performance, or durabilityand may contravene regulations. Inaddition, damage or performanceproblems resulting from modificationmay not be covered under warranty.

Copying, quoting or reproduction of anypart of this manual is not permittedwithout explicit approval by MARUTISUZUKI INDIA LIMITED.

0-2

wwwww WARNINGYour vehicle has monocoque bodyconstruction which provides forcertain crumple zones in the bodywhich absorbs larger part of impactenergy in the event of a front collisionand protects the occupants fromimpact. Do not use any fitmentssuch as crash guards. Thesefitments will increase the risk to theoccupants because of the shockdirectly getting transmitted to theoccupants.

CAUTIONImproper instl lation of mobilecommunication equipment such ascellular telephones or CB (Citizen'sBand) radios may cause electronicinterference with your vehicle'signition system, resulting in vehicleperformance problems. Consult yourMARUTI SUZUKI dealer or qualifiedservice technician for advice oninstalling such mobile communi-cation equipment.76G-00-001

The circle with a slash in this manualmeans “Don’t do this” or Don’t let thishappen”.

5

59K,76G,844-74E

1MAINTENANCE SERVICE RECORD

IMPORTANT INFORMATION TO CUSTOMER

Dear CustomerFor any assistance with regard to our product, please contactGeneral Manager/Works Manager at any of our Dealer orAuthorised Service Station. For additional enquiry you maycontact our Regional office or Service Department. TheAddresses and Phone nos. are given in Service Networkbooklet provided along with vehicle.

MODEL CHASSIS NO. ENGINE NO. KEY NO. DATE OF MILEAGE BATTERY DELIVERY (km) MAKE SR. NO./BATCH CODE

OWNER’S NAME & ADDRESS ____________________________________________________________________________

_____________________________________________________________________ TEL. NO. _________________________

ADDRESS/STAMP OF SELLING DEALER SELLING DEALER CODE

SHOWROOM

WORKSHOP

MAINTENANCE SERVICE RECORD

1-1

6

59K,76G,844-74E

F....free Service P....Paid Service W....Warranty. A....Accident

MAINTENANCE SERVICE RECORD

DATE OF KIND OF MILEAGE DESCRIPTION OF JOB NAME OF SERVICING JOB CARD MECHANIC’SSERVICE SERVICE (km) DEALER/MASS NO. SIGNATURE

1-2

7

59K,76G,844-74E

2

WARRANTY POLICYMaruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),warrants that each new Maruti Suzuki vehicle distributed in Indiaby Maruti Suzuki and sold by an authorised Maruti Suzuki dealerwill be free, under normal use and service, from any defects inmaterial and workmanship at the time of manufacture SUBJECTTO THE FOLLOWING TERMS AND CONDITIONS:

(1) Qualification:To qualify for this warranty:

(a) The Maruti Suzuki vehicle must be delivered by MarutiSuzuki authorised dealer and set-up, serviced by MarutiSuzuki authorised dealer/service station.

(b) The warranty registration card in respect of each vehiclemust be completed by the dealer at the time of deliveryof the vehicle and dealer should retain the same.

(2) Term:The term of the warranty shall be twenty four (24) monthsor 40,000 kilometers (whichever occurs first) from the dateof delivery to the first owner.

(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehiclewithin the term stipulated above, Maruti Suzuki only obligationis to repair or replace at its sole discretion any part shownto be defective, with a new part or the equivalent at no costto the owner for parts or labour, when Maruti Suzukiacknowledges that such a defect is attributable to faulty materialor workmanship at the time of manufacture. The owner isresponsible for any repair or replacements which are not

covered by this warranty.(4) Limitation:

This warranty shall not apply to:(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluidchanges, headlight aiming, fastener retightening, wheelbalancing, wheel alignment and tyre rotation, cleaning ofinjectors, adjustments of carburettor, ignition timing, clutchand valve clearance.

(b) the replacement of normal wear parts including withoutlimitation, bulbs, battery, tyres and tubes, spark plugs, belts,hoses, filters, wiper blades, brushes, contact points, fuses,clutch disc, brake shoes, brake pads, cable and all rubberparts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.(d) any repairs or replacement required as a result of accidents

or collision.(e) any defects caused by misuse, negligence, abnormal use

or insufficient care.(f) any vehicle which has been modified or altered, including

without limitation, the installation of performanceaccessories.

(g) any vehicle on which parts or accessories not approvedby Maruti Suzuki have been used.

(h) any vehicle which has not been operated in accordancewith the operating instructions in the Maruti Suzuki Owner’sManual.

(i) any vehicle which has not received, during the warrantyterm, the service inspections prescribed in the MarutiSuzuki Owner’s Manual.

(j) any vehicle which has been assembled, disassembled,

WARRANTY POLICY

2-1

8

59K,76G,844-74E

adjusted or repaired by other than an Maruti Suzukiauthorised dealer/service station.

(k) any vehicle which has been used for purposes other thanwhat it was designed for.

(l) any damage or deterioration caused by industrial pollutionand bird droppings.

(m) insignificant defects which do not affect the function of thevehicle including without limitation, sound, vibration and fluidseep.

(n) any natural wear and tear including without limitation, agingetc.

(o) Installation and usage of Domestic LPG Gas/LPG cylinder.

For Maruti Suzuki Air-Conditioned Vehicles(p) V-belts, hoses and gas leaks.

(5) Extent of Warranty:This warranty is the entire written warranty given by MarutiSuzuki for Maruti Suzuki vehicles and no dealer or its or hisagent or employee is authorised to extend or enlarge thiswarranty and no dealer or its or his agent or employee isauthorised to make any oral warranty on Maruti Suzuki behalf.Maruti Suzuki reserves the right to add any improvements orchange the design of any model at any time with no obligationto make the same changes on units previously sold.

(6) Warranty Service:To obtain warranty service, the complete vehicle must bepresented at the owner’s expenses to any authorised MarutiSuzuki dealer.

(7) Owner’s Warranty Responsibilities:It is responsibility of each owner to:(a) make certain that the warranty registration/PDI card was

completed at the time of delivery of the vehicle;(b) have performed, at his own expenses, by an Maruti Suzuki

authorised dealer/service station all the service inspectionsspecified in the Maruti Suzuki “Owner’s Manual and ServiceBooklet” and maintain adequate proof that such serviceinspections have been performed.

(c) make certain that the Maruti Suzuki authorised dealer/servise station performing the service inspection hascertified the work on the “Maintenance Service Record”page in the “Owner’s Manual and Service Booklet” and

(d) present the Maruti Suzuki “Owner’s Manual and ServiceBooklet” to the authorised Maruti Suzuki dealer wheneverrequesting service inspections or warranty service.

If the “Owner’s Manual and Service Booklet” should be lost ordestroyed the owner should consult the authorised Maruti Suzukidealer from whom the vehicle was purchased for instructionsconcerning replacement of the “Owner’s Manual and ServiceBooklet”.

(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle, lossof time, inconvenience or any other indirect incidental orconsequential damage resulting from the vehicle not beingavailable to the owner because of any defect covered by thiswarranty.

(9) Change of OwnerEven if ownership of the vehicle changes, the remainingwarranty period is effective for the new owner.

WARRANTY POLICY

2-2

9

59K,76G,844-74E

Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles (apart from the Regular warranty and will run parallelto the regular product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect fromJuly 1st, 2001.

Terms:

The Emission Warranty will be applicable for 80,000 kms or 3 years (Which ever comes earlier) from the date of delivery tothe first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of allvalid document.

Conditions:

1. Under Emission Warranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet to theEmission Standard as specified in sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989.

2. The warranty claims will only be accepted after examination carried out by Maruti Suzuki or it's dealer which leads to firm conclusionsthat the

a) Original settings have not been tempered in any case.

b) Part (as given in Annexure-A) has a manufacturing defect.

c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and usedin accordance with the instructions as specified in Owner's Manual and Service Booklet and the used fuel and different oils(Engine oil, Transmission oil, Brake oil etc.) are also as per specification.

3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti Suzuki and it's dealerand results of the examination will be final and binding. If after examination, the warrantable condition is not established, MarutiSuzuki and it's dealer has the right to charge all, or part of the cost of such examination.

4. Under Emission Warranty, the parts (as given in Annexure-A) will be changed free of cost, but the consumables will be chargedas per actual.

5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these beingintegral parts a complete assembly, Maruti Suzuki and it's dealer will have the sole discretion to replace entire assembly or byusing some of the parts of the system through suitable repair or modifications.

EMISSION WARRANTY

2-3

10

59K,76G,844-74E

6. Any consequential repairs or replacement of parts which may be found necessary to establish compliance of Emission Warranty,will not be considered under warranty, unless the same is under product warranty. The consumable will be charged as per actualunder such repair or replacement.

7. Maruti Suzuki will not be responsible for the cost of transportation of the vehicle to the nearest Maruti Suzuki dealer workshopor any loss due to non-availability of the vehicle during the period of lodging of a warranty claim and examination and/or repairby Maruti Suzuki dealer.

8. Maruti Suzuki will not be responsible for any penalty that may be charged by statutory authorities on account of failure to complywith the EMISSION STANDARDS.

9. Emission Warranty will not be affected on the change of owner, provided all the documents are available.

10. All maintenance actions (as specified in the Owner's Manual and Service Booklet) need to be followed and recorded in the manualfor emission warranty.

11. The customer needs to produce the PUC (Pollution Under Control) certificate valid for the period preceding the test during whichthe failure is discovered. The receipts (for the maintenance of the vehicle as per specification in Owner's Manual and ServiceBooklet from the date of original purchase of the vehicle) will also be required.

Condition Under which the Emission Warranty is not APPLICABLE

1. In the absence of valid PUC certificate.

2. Vehicle not serviced from Maruti Suzuki authorised workshop as per the schedule specified in the Owner's Manual.

3. Vehicle subjected to abnormal use (accident, motor race, rallies or for the purpose of establishing the records etc.)

4. Use of non MGP (Maruti Genuine Part).

5. Vehicle tempered in an unauthorised manner.

6. Tampering with odometer so that the actual kilometer reading can not be read.

7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmission oil and Brake oil etc.)

EMISSION WARRANTY

2-4

11

59K,76G,844-74E

Annexure-A

List of parts covered under Emission Warranty

1. Fuel injection Assembly, Pressure Regulator, Throttle Body Assembly.

2. Electronic Control Module (ECM).

3. Intake Manifold.

4. EGR valve.

5. Distributor and internal parts.

6. Ignitions coil.

7. Canister Assembly.

8. Vapour Liquid Separator.

9. Fuel Tank and Filler Cap.

10. PCV (Positive Crankcase Ventilation) Valve.

11. Oil Filler Cap.

12. Catalytic Convertor.

13. Exhaust manifold.

14. All fuel injection System related SENSORS.

15. Maniverter

EMISSION WARRANTY

2-5

13

76G-74E

3

BEFORE DRIVING

BEFORE DRIVING

Fuel Recommendation ....................................................................................... 3-1

Immobilizer System ............................................................................................ 3-2

Door Locks .......................................................................................................... 3-4

Windows ............................................................................................................... 3-6

Mirrors ................................................................................................................... 3-8

Front Seat Adjustment ...................................................................................... 3-9

Adjusting Seat Position .................................................................................... 3-9

Adjusting Seatbacks ........................................................................................3-10

Seat Belts ..........................................................................................................3-11

Lap Belt (if equipped) .....................................................................................3-15

14

76G-74E

3-1

BEFORE DRIVING

FUEL RECOMMENDATION

You must use unleaded petrol with anoctane number (RON) of 91 or higher.

Use of leaded fuel in vehicle equippedwith catalytic converter is prohibited,because lead deactivates the pollutantreducing components of catalyticconverter and may result in permanentdamage to catalytic converter.

Be careful not to spill fuel containingalcohol while refuelling. If fuel isspilled on the vehicle body, wipe it upimmediately. Fuels containing alcoholcan cause paint damage, which is notcovered under New Vehicle LimitedWarranty.

The fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuelafter the filler nozzle has automaticallyshut off or an initial blowback occurs,the air chamber will become full.Exposure to heat when fully fuelled inthis manner will result in leakage dueto fuel expansion. To prevent suchfuel leakage, stop filling after the fillernozzle has automatically shut off, orwhen using an alternative nonautomatic system, initial ventblowback occurs.

Petrol/Ethanol BlendsBlends of unleaded petrol and ethanol (grainalcohol), also known as gasohol, arecommercially available in some areas.Blends of this type may be used in yourvehicle if they are no more than 5% ethanol.Make sure this petrol-ethanol blend hasoctane ratings no lower than thoserecommended for petrol.

Petrol/Methanol BlendsBlends of unleaded petrol and methanol(wood alcohol) are also commerciallyavailable in some areas. DO NOT USEfuels containing more than 5% methanolunder any circumstances. Fuel systemdamage or vehicle performance problemsresulting from the use of such fuels are notthe responsibility of MARUTI SUZUKI andmay not be covered under Warranty.

Fuels containing 5% or less methanol maybe suitable for use in your vehicle if theycontain cosolvents and corrosion inhibitors.

NOTE:If you are not satisfied with the driveabilityor fuel economy of your vehicle when youare using a petrol/alcohol blend, you shouldswitch back to unleaded petrol containing noalcohol.

CAUTION

CAUTION

CAUTION

15

76G-74E

Your vehicle comes with a pair of identicalkeys. Keep the spare key in a safe place.One key can open all of the locks on thevehicle.

The key identification number is stamped ona metal tag provided with the keys. Keepthe tag in a safe place. If you lose yourkeys, you will need this number to havenew keys made. Write the number downand keep it in a safe accessible place awayfrom the vehicle.

BEFORE DRIVING

3-2

wwwww WARNING• Do not use locally made key.• Should you require a duplicate key,

place your order with a MARUTISUZUKI dealer only.

Note:Keep the spare key very carefully. When itis lost, consult your dealer by quoting keynumber.

Immobilizer SystemThis system is designed to help preventvehicle theft by electronically disabling theengine starting system.

The engine can be started only with yourvehicle’s original immobilizer ignition keywhich has an electronic identification codeprogrammed into it. The key communicatesthe identification code to the vehicle whenthe key is turned to the “ON” position. Ifyou need to make spare keys, contact yourMARUTI SUZUKI dealer. The vehicle mustbe programmed with the correct identifica-tion code for the spare keys. A key madeby an ordinary locksmith will not work.

Key Number :

IMMOBILIZER KEYS

76G-03-002

16

76G-74E

3-3

CAUTIONIn case of attaching any metal objectsto the immobilizer key, it may notstart the engine.The immobilizer key is a sensitiveelectronic instrument. To avoiddamaging the immobilizer key:• Do not expose it to impacts,

moisture or high temperature suchas by leaving it on the dashboardunder direct sunlight.

• Keep the immobilizer key away frommagnetic objects.

If the Immobilizer system light (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrongwith your key or with the immobilizer sys-tem. Contact your MARUTI SUZUKI dealerto inspect the system.

Ignition Key Reminder (if equipped)A buzzer sounds intermittently to remindyou to remove the ignition key if it is in theignition switch when the driver's doors isopened.

BEFORE DRIVING

NOTE:• If you lose your Immobilizer ignition key,

contact your MARUTI SUZUKI dealer assoon as possible to have the lost onedeactivated, then have the new keymade by them.

• If you own other vehicles withimmobilizer keys, keep those keys awayfrom the ignition switch when using yourvehicle, or the engine may not bestarted because they may interfere withyour vehicle’s immobilizer system.

76G-03-003 76G-03-004

17

76G-74E BEFORE DRIVING

3-4

Central door locking system (if equipped)You can lock and unlock all doors simultan-eously by using the key in the driver’s doorlock.

To lock all doors simultaneously, insert thekey in the driver’s door lock and turn thetop of the key toward the rear of thevehicle.

To unlock all doors simultaneously, insertthe key in a driver’s door lock and turn thetop of the key toward the front of thevehicle.

You can also lock or unlock all the sidedoors by pushing down or pulling up thedriver's door lock knob.

76G-03-007

Side Door LocksTo lock the driver's door from outside the vehicle:a) Insert the key fully and turn the top of

the key toward the rear of the vehicle,or

b) Push in the lock knob down and hold thedoor handle up as you close the door.

To unlock the driver's door from outside thevehicle, insert the key fully and turn the topof the key toward the front of the vehicle.To lock a front passenger’s door fromoutside the vehicle, turn the lock knobforward, then pull and hold the door handleas you close the door.To lock a rear door from outside thevehicle, push in the lock knob down andclose the door.

To lock a door from inside the vehicle, pushthe lock knob down. Pull the lock knob upto unlock the door.

wwwww WARNING

DOOR LOCKS

76G-03-005 76G-03-006

Always lock all doors when driving.Locking the door prevents occupantsfrom being thrown from the vehiclein the event of an accident. It alsohelps prevent unintentional openingof the doors.

18

76G-74E

NOTE:• Moving the lock knob on passenger's

door locks or unlocks the passenger'sdoor only.

• Be sure to hold the door handle upwhen you close a locked front door, orthe door will not remain locked.

wwwww WARNING

Child-Proof Locks (if equipped)As illustrated, a child-proof lock is providedfor both rear doors. When the lock lever isdown, position 1, the child proof lock isactivated, and when up, in position 2 thechild-proof lock is deactivated, when thechild-proof lock is activated, the rear doorcannot be opened from the inside even ifthe inside door lock is unlocked but can beopened from the outside.

Be sure to place the child-proof lockin the locked position wheneverchildren are seated in the rear.

Rearend Door LockTo unlock the door, insert the key into thelock knob and turn it clockwise.

76G-03-008 76G-03-009

TYPE-1 (ALTO)EXAMPLE

3-5

BEFORE DRIVING

19


3-6

wwwww WARNING

76G-03-009A

Always make sure that the rearenddoor is closed and latched securely.Closing the door completely helps toprevent exhaust gases from enteringthe vehicle. Completely closing therearend door also helps preventoccupants from being thrown from thevehicle in the event of an accident.

TYPE-2 (ALTO K10)

WINDOWS

Raise or lower the door windows by turningthe handle located on the door panel.

76G-03-011

Electric window controls (if equipped)The driver’s door has switches 1 & 2 tooperate the driver’s window and frontpassenger’s window respectively.

The passenger’s door only has a switch 3to operate the passenger’s window. Theelectric windows can only be operated whenthe ignition switch is in the “ON” position.

To open a window with the driver's doorswitches, push the top part of the switchand to close the window lift up the top partof the switch.

76G-03-012

20

76G-74E

The driver’s window has an “auto-down”feature for added convenience (at tollbooths or drive-through restaurants, forexample). This means you can open thewindow without holding the window switchin the “Down” position. Press the driver’swindow switch completely down and releaseit. To stop the window before it reaches thebottom, lift up the switch briefly.

To open or to close a window with thepassenger's door switch, push the top partof the switch or lift up the top part of theswitch respectively.

76G-03-013

3-7

BEFORE DRIVING

The driver’s door also has a lock switch forthe passenger’s window. When you push inthe lock switch, the passenger’s windowcan not be raised or lowered by operatingeither of the switches 2 or 3. To restorenormal operation, push the switch again.

76G-03-014

wwwww WARNINGYou should always push in the lockswitch when there are children in thevehicle. Children can be seriouslyinjured if they get part of their bodycaught by the window duringoperation.

Since the electric windows consumesa large amount of electricity, the sameshould not be used excessively withengine in “OFF” condition.

CAUTION

21


3-8

MIRRORS

Inside Rearview MirrorTo adjust the inside rearview mirror, movethe mirror up, down, or sideways to obtainthe best view.

76G-03-015

Outside Rearview MirrorsAdjust the outside rearview mirrors (with thehelp of control lever, if equipped), so thatyou can just see the side of your vehiclein the mirrors.

Be careful when judging the size ordistance of a vehicle or other objectseen in the side convex mirror (ifequipped). Be aware that objects looksmaller and appear farther away thanwhen seen in a flat mirror.

wwwww WARNING

76G-03-017 76G-03-017A

TYPE-1 (ALTO) TYPE-2 (ALTO K10)

22

76G-74E

3-9

BEFORE DRIVING

FRONT SEAT ADJUSTMENT

76G-03-018

TYPE-1 (ALTO)

76G-03-018A

TYPE-2 (ALTO K10)

ADJUSTING SEAT POSITION

76G-03-019A

76G-03-019B

TYPE-1 (ALTO)

TYPE-2 (ALTO K10)

Never attempt to adjust the driver’sseat or seatback while driving. Theseat or seatback could moveunexpectedly, causing loss of control.Make sure that the driver’s seat andseatback are properly adjusted beforeyou start driving.

wwwww WARNING

23


3-10

The adjustment lever for each front seat islocated under the front of the seat. Toadjust the seat position, pull up on theadjustment lever and slide the seat forwardor rearward. After adjustment, try to movethe seat forward and rearward to ensurethat it is securely latched.

wwwww WARNINGTo avoid excessive seat belt slack,which reduces the effectiveness of theseat belts as a safety device, makesure that the seats are adjustedbefore the seat belts are fastened.

Seatbacks should always be in anupright position when driving, or seatbelt effectiveness may be reduced.Seat belts are designed to offermaximum protection when seatbacksare in the fully upright position.

Front SeatsThe seatbacks can be adjusted to differentangles. To adjust the seatback angle, pullup the lever on the outboard side of theseat, move the seatback to the desiredposition, and release the lever to lock theseatback in place.

wwwww WARNING

76G-03-022

76G-03-023

TYPE-1 (ALTO)

TYPE-2 (ALTO K10)

ADJUSTING SEATBACKS

24

76G-74EBEFORE DRIVING

3-11

Seat belts are good help to protectoccupants from injury or death in theevent of accidents. We urge you towear seat belts at all times if the beltsare equipped. If seat belts are notequipped at the rear seating positions,we recommend you to install optionalor after market high quality seat beltsto increase occupant's safety.

SEAT BELTS

wwwww WARNING

76G-03-026

• Never allow persons to ride in thecargo area of a vehicle. In the eventof an accident, there is a muchgreater risk of injury for personswho are not riding in a seat withtheir seat belt securely fastened.

• Seat belts should always beadjusted so the lap portion of thebelt is worn low across the pelvis,not across the waist. Shoulderstraps should be worn on theoutside shoulder only, and neverunder the arm. Seat belts shouldnever be worn with the strapstwisted and should be adjusted as

wwwww WARNING

VV VVV

76G-03-027

tightly as is comfortable to providethe protection for which they havebeen designed. A slack belt willprovide less protection than onewhich is snug.

• Make sure that each seat belt buckleis inserted into the proper bucklecatch.

• Do not wear your seat belt overhard or breakable objects in yourpockets or on your clothing. If anaccident occurs, objects such asglasses, pens, etc. under the seatbelt can cause injury.

wwwww WARNING

VVVV V

VV VVV

76G-03-028

25


3-12

• Never use the same seat belt onmore than one occupant and neverattach a seat belt over an infant orchild being held on an occupant’slap. Such seat belt use could causeserious injury in the event of anaccident.

• Pregnant women should use seatbelts, although specific recommen-dations about restraint use shouldbe made by the woman’s medicaladvisor. Remember that the lapportion of the belt should be wornas low as possible across the hips,as shown in the diagram.

wwwww WARNING

VVVV V

VV VVV

76G-03-029

• Periodically inspect seat beltassemblies for excessive wear anddamage. Seat belts should bereplaced if webbing becomes frayed,contaminated, or damaged in anyway. It is essential to replace theentire seat belt assembly after it hasbeen stressed in an impact, even ifdamage to the assembly is notobvious.

• Infants and small children shouldnever be transported unless they areproperly restrained. Restraintsystems for infants and smallchildren can be purchased locallyand should be used. Make sure thatthe system you purchase meetsapplicable safety standards. Readand follow all the directionsprovided by the manufacturer.

• Avoid contamination of seat beltwebbing by polishes, oils,chemicals, and particularly batteryacid. Cleaning may safely be carriedout using mild soap and water.

• For children, if the shoulder beltirritates the neck or face, move thechild closer to the center of thevehicle.

wwwww WARNING

VVVV VVV VVV

Be sure to inspect all seat beltassemblies after any collision. Anyseat belt assembly which was in useduring a collision (other than a veryminor one) should be replaced, evenif damage to the assembly is notobvious. Any seat belt assemblywhich was not in use during acollision should be replaced if it doesnot function properly or is damagedin any way.

wwwww WARNING

VVVV V

26


3-13

76G-03-031

76G-03-032

To reduce the risk of sliding under the beltduring a collision, position the lap portionof the belt across your lap as low on yourhips as possible and adjust the belt to asnug fit using the proper method for eachtype of the belt as described below. Makesure that the belt is not twisted.

76G-03-033

To fasten the seat belt, sit up straight andwell back in the seat, pull the buckle tongueattached to the seat belt across your bodyand slide it into the buckle catch on theopposite side until you hear a “click”.

76G-03-030

27


3-14

wwwww WARNING

To Adjust the Belt

• Pull the shoulder portion of the beltupwards through the tongue plate.

The length of the diagonal shoulder strapadjusts itself to allow freedom of movement.The seat belt has an emergency lockingretractor (ELR), which is designed to lockthe seat belt only during a sudden stop orimpact.

No modifications or additions of anysort should be made to the seat beltor its operating mechanism.

76G-03-035

Seat Belt InspectionPeriodically inspect the seat belts to makesure they work properly and are notdamaged. Check the webbing, buckles, latchplates, retractors, anchorages and guideloops. Replace any seat belts which do notwork properly or are damaged.

76G-03-036

To unfasten the belt, press the releasebutton on the buckle catch.

76G-03-034

28


3-15

To lengthen, release the tounge from thebuckle unit, pull the tounge (adjuster) inthe direction of the arrow, at right anglesto the belt. The tounge should then berefitted into the buckle unit and the belttightened as previously described.

76G-03-038

NOTE:To identify the center seat belt buckle catchand tongue in the rear seat, "CENTER" ismoulded on the buckle catch and tongue ofthe center lap belt. The buckle catches aredesigned so a buckle tongue can not beinserted into the wrong buckle catch.

76G-03-039

On this belt the adjuster is incorporated inthe tounge unit.

To tighten the belt, pull the free end ofthe belt across alongside the lap strapuntil it is adjusted to a snug comfortableposition.

LAP BELT (if equipped)

76G-03-037

29

76G-74E

4

STEERING COLUMN CONTROLS


Ignition Switch .................................................................................................... 4-1

Lighting/Turn Signal Control Lever ................................................................ 4-2

Hazard Warning Switch .................................................................................... 4-5

Windscreen Wiper and Washer Lever .......................................................... 4-5

Horn ....................................................................................................................... 4-6

Electrical Power Steering (if equipped) ........................................................ 4-7

30

76G-74E

IGNITION SWITCH

The ignition switch has the following fourpositions:

• Do not use any locally made key.• Should you require duplicate key,

place your order with MARUTISUZUKI dealer only.

LOCKThis is the normal parking position. It is theonly position in which the key can beremoved.

The “LOCK” position locks the ignition, andprevents normal use of the steering wheelafter the key is removed.

To release the steering lock, fully insert thekey and turn it clockwise to one of the otherpositions. If you have trouble turning thekey to unlock the steering, try turning thesteering wheel slightly to the right or leftwhile turning the key.

To avoid possible injury, do not operatecontrols by reaching through the steeringwheel.


wwwww WARNING

wwwww WARNING

4-1

76G-04-001 76G-04-00376G-04-002

31

76G-74E

• Do not use the starter motor formore than 15 seconds at a time. Ifthe engine does not start; wait 15seconds before trying again. If theengine does not start after severalattempts, check the fuel and ignitionsystems or consult your MARUTISUZUKI dealer.

• Do not leave the ignition switch inthe “ON” position if the engine isnot running as the battery willdischarge.

LIGHTING/TURN SIGNALCONTROL LEVER


ACCAccessories such as the radio can operate,but the engine is off.

ONThis is the normal operating position. Allelectrical systems are on.

STARTThis is the position for starting the engineusing the starter motor. The key should bereleased from this position as soon as theengine starts.

• Never remove the ignition key whilethe vehicle is moving. The steeringwheel will lock and you will not beable to steer the vehicle.

• Do not leave children alone in aparked vehicle. Unattended childrencould cause accidental movement ofthe vehicle, which could result insevere personal injury.

• Always remove the key when parkedto prevent unintentional operation ofthe vehicle and to improve security.

wwwww WARNINGCAUTION

4-2

76G-04-00576G-04-004

ALTO

76G-04-005A

ALTO K10 TYPE-1

32

76G-74ESTEERING COLUMN CONTROLS

4-3

76G-04-005B

With the headlights on, push the leverforward to switch to the high beams (mainbeams) or pull the lever toward you toswitch to the low beams. When the highbeams (main beams) are on, a light on theinstrument panel will come on. To flash thehigh beams (main beams) pull the leverslightly towards you and release it.

76G-04-006

ALTO K10 TYPE-2

76G-04-006A

76G-04-006B

ALTO K10 TYPE-1

ALTO K10 TYPE-2ALTO

This control lever is located on the outboardside of the steering column. Operate thelever as described below.

Lighting OperationTo turn the lights on or off, twist the knobon the end of the lever. There are threepositions: in the “OFF” position all lights areoff; in the middle position the front parkinglights, tail-lights, registration plate light, andinstrument lights are on, but the headlightsare off; in the third position the headlightscome on in addition to the other lights.

33

76G-74E STEERING COLUMN CONTROLS

Turn Signal OperationWith the ignition switch in the “ON” position,move the lever up or down to activate theleft or right turn signals.

Normal Turn SignalMove the lever clockwise until it clicks tosignal a right turn or anticlockwise to signala left turn. When the turn is completed, thesignal will cancel and the lever will returnto its normal position.

4-4

76G-04-00876G-04-007

76G-04-007A

76G-04-007B

ALTO K10 TYPE-1

ALTO K10 TYPE-2ALTO ALTO

76G-04-008A

ALTO K10 TYPE-1

34


WINDSCREEN WIPER ANDWASHER LEVER

Windscreen WipersTo turn the windscreen wipers on, move thelever down to one of the three operatingpositions. In the “INT” position, (if equipped)the wipers operate intermittently. The “INT”position is very convenient for driving in mistor light rain. In the “LO” position the wipersoperate at a steady low speed. In the “HI”position, the wipers operate at a steady highspeed. To turn off the wipers, move thelever back to the “OFF” position.

4-5

HAZARD WARNING SWITCH

Push in the marked part of the hazardwarning switch to activate the hazardwarning lights. All four turn signal lights andboth turn signal indicators will flashsimultaneously. To turn off the lights, pushthe switch once again.

Use the hazard warning lights to warn othertraffic during emergency parking or whenyour vehicle could otherwise become atraffic hazard.

76G-04-009 76G-04-01076G-04-008B

ALTO K10 TYPE-2

Lane Change SignalSome times, such as when changing lanes,the steering wheel is not turned far enoughto cancel the turn signal. For convenience,you can flash the turn signal by moving thelever part way and holding it there. Thelever will return to its normal position whenyou release it.

35

76G-74E STEERING COLUMN CONTROLS

HORN

To prevent damage to the windscreenwiper and washer system components,you should take the followingprecautions:• Do not continue to hold in the lever

when there is no windscreen washerfluid being sprayed or the washermotor can be damaged.

• Do not attempt to remove dirt froma dry windscreen with the wipers oryou can damage the windscreen andthe wiper blades. Always wet thewindscreen with washer fluid beforeoperating the wipers.

• Clear ice or packed snow from thewiper blades before using thewipers.

• Check the washer fluid levelregularly. Check it often when theweather is bad.

• Only fill the washer fluid reservoir3/4 full during cold weather to allowroom for expansion if thetemperature falls low enough tofreeze the solution.

Press the horn button of the steering wheelto sound the horn. The horn will sound withthe ignition switch in any position.

CAUTION

4-6

76G-04-012

Windscreen WasherTo spray windscreen washer fluid, pull thelever toward you. The windscreen wiperswill automatically turn on at low speed ifthey are not already on and the "INT"position is equipped.

• To prevent windscreen icing in coldweather, turn on the defroster to heatthe windscreen before and duringwindscreen washer use.

• Do not use radiator antifreeze in thewindscreen washer reservoir. It canseverely impair visibility whensprayed on the windscreen, and canalso damage your vehicle’s paint.

wwwww WARNING

76G-04-011

EXAMPLE

36


4-7

ELECTRIC POWER STEERING(If equipped)

Depending on specifications, your vehicle isequipped with electric power steeringsystem to reduce the steering effort whiledriving.

76G-04-013

37

76G-74E

5

INSTRUMENT PANEL

INSTRUMENT PANEL

Instrument Panel ................................................................................................ 5-1

Instrument Cluster ............................................................................................. 5-2

Warning and Indicator Lights ......................................................................... 5-4

Speedometer ........................................................................................................ 5-7

Odometer/Tripmeter ............................................................................................ 5-8

Tachometer (if equipped) ................................................................................. 5-9

Fuel Gauge .......................................................................................................... 5-9

High Engine Coolant Temperature Warning Light (Red Color) .............. 5-9

Glove Box ..........................................................................................................5-10

Head Light Leveling Switch ..........................................................................5-10

Heating System (if equipped) ........................................................................5-11

System Operating Instructions ...................................................................... 5-12

Air Conditioning System (if equipped) .......................................................5-17

System Operating Instructions ...................................................................... 5-17

38

76G-74EINSTRUMENT PANEL

1. Instrument cluster2. Ignition switch3. Lighting switch/Turn signal and

dimmer switch4. Windscreen wiper and washer switch5. Hazard warning switch

6. Other switches (if equipped)7. Heater control panel (if equipped)

8. Ashtray (if equipped)9. Bonnet release (if equipped)

10. Center ventilator11. Side ventilator12. Side defroster13. Glove box14. Fuse box

5-1

INSTRUMENT PANEL

76G-05-001

76G-05-002

TYPE-1 (ALTO)

TYPE-2 (ALTO / ALTO K10)

39

76G-74E INSTRUMENT PANEL

1 Speedometer2 Odometer/Trip meter3 Odometer/Trip meter selector knob4 Fuel gauge5 High Temperature Coolant warning lamp6 Warning and indicator lights

5-2

INSTRUMENT CLUSTER (ALTO)

76G-05-003

40

76G-74E

1 Speedometer2 Odometer/Trip meter3 Odometer/Trip meter selector knob4 Tachometer (if equipped)5 Fuel gauge6 High Temperature Coolant warning lamp7 Warning and indicator lights

INSTRUMENT CLUSTER (ALTO K10)

76G-05-004

76G-05-004A

TYPE-2

TYPE-1

INSTRUMENT PANEL

5-3

41

76G-74E

WARNING AND INDICATOR LIGHTS

Brake fluid level warning/Parking BrakeIndicator light

This light operates under three different typeof operations :1) The light comes on briefly when theignition switch is turned to the “ON” postion.2) The light comes on when the parkingbrake is engaged with the ignition switch inthe “ON” position.3) The light comes on when the fluid in thebrake fluid reservoir falls below theadequate level.

The light should go out after starting theengine and fully releasing the parking brake,if the fluid level in the brake fluid resevoiris adequate.

If the light does not go off or comes onwhilst your driving, it may mean that thereis something wrong with the vehicle'sbraking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance maybe longer, you may have to push harderon the pedal, and the pedal may godown farther than normal.

2) Test the brakes by carefully starting andstopping at the side of the road.

3) If you determine that it is safe, drivecarefully at low speed to the nearestdealer for repairs. or

4) Have the vehicle towed to the nearestdealer for repairs.

INSTRUMENT PANEL

wwwww WARNINGwwwww WARNING

5-4

NOTE:Because the disc brake system is selfadjusting, the fluid level will drop as thebrake pads become worn.Replenishing the brake fluid reservoir isconsidered normal periodic maintenance.

76G-05-005

If any of the following conditions occur,you should immediately ask yourMARUTI SUZUKI dealer to inspect thebrake system.• If the brake fluid level warning light

does not go out after the engine hasbeen started and the parking brakehas been fully released.

• If the brake fluid level warning lightdoes not come on when the ignitionswitch is turned to the “ON” positionwith the parking brake applied.

• If the brake fluid level warning lightcomes on at any time during vehicleoperation.

42


• If you operate the engine with thislight on, severe engine damage canresult.

• Do not rely on the Oil PressureLight to indicate the need to add oil.Be sure to periodically check theengine oil level (see section"INSPECTION & MANINTENANCE").

5-5

CAUTION

Charging LightThis light comes on when the ignition switchis turned on, and goes out when the engineis started. The light will come on andremain on if there is something wrong withthe battery charging system. If the lightcomes on when the engine is running, thecharging system should be inspectedimmediately by your MARUTI SUZUKIdealer.

Do not continue driving long with thecharging light ON as this will drain thebattery 'dead'.

CAUTION

76G-05-007

76G-05-008

EXAMPLE

Oil Pressure LightThis light comes on when the ignition switchis turned on, and goes out when the engineis started. The light will come on andremain on if there is insufficient oil pressure.If the light comes on when driving, pull offthe road as soon as you can and stop theengine. Check the oil level and add oil ifnecessary (see section "INSPECTION &MAINTENANCE"). If there is enough oil, thelubrication system should be inspected byyour MARUTI SUZUKI dealer before youdrive the vehicle again.

76G-05-006

43


5-6

Immobilizer System LightWhen the ignition switch is turned to the“ON” position, this light comes on to let youknow the light is working. If this light blinkswith the ignition switch turned to “ON”, theremay be something wrong with the immobi-lizer system. Contact your MARUTI SUZUKIdealer to have the system inspected.

76G-05-010

Electric Power Steering Light(if equipped)

This light comes on when the ignition switchis turned to the “ON” position, and goes outwhen the engine is started.

If this light comes on while driving, thepower steering system may not work prop-erly. Have the system inspected by yourMARUTI SUZUKI Authorized workshop.

NOTE:If the power steering system does not workproperly, you will feel heavier to steer butyou still will be able to steer.

76G-05-009A“Malfunction Indicator” LightYour vehicle has a computer-controlledemission control system. A “MalfunctionIndicator” light is provided on the instrumentpanel to indicate when it is necessary tohave the emission control system serviced.The “Malfunction Indicator” light comes onwhen the ignition switch is turned to “ON”and goes out when the engine is started.

If the “Malfunction Indicator” light comes onwhen the engine is running, there is aproblem with the emission control system.Take the vehicle to your MARUTI SUZUKIdealer to have the problem corrected.

Continuing to drive the vehicle whenthe “Malfunction Indicator” light is oncan cause permanent damage to thevehicle’s emission control system, andcan affect fuel economy anddriveability.

CAUTION

76G-05-009

44


5-7

76G-05-013A

76G-05-013B

SPEEDOMETER

The speedometer (1) indicates vehiclespeed in km/h.

76G-05-013

ALTO K10 TYPE-1

ALTO K10 TYPE-2ALTO

Turn Signal IndicatorsWhen you turn on the left or right turnsignals, the corresponding green arrow onthe instrument panel will flash along with therespective turn signal lights. When you turnon the hazard warning switch, both arrowswill flash along with all of the turn signallights.

Main Beam (High Beam) Indicator LightThis indicator comes on when headlightmain beams (high beams) are turned on.

76G-05-011

76G-05-012

45


5-8

Push the selector knob for a little while(about 2 seconds) to reset the trip meterto zero.

76G-05-016

When the ignition switch is turned to "ON"the display shows the odometer or tripmeter.

The display shows three types of indication;odometer, trip meter A and/or trip meter B.Push the selector knob quickly to switch theindication among the three.

You can use the two trip meters (A and B)independently.

76G-05-01576G-05-014

ODOMETER/TRIPMETER

The odometer (2) records the total distancethe vehicle has been driven. The trip meter(3) can be used to measure the distancetravelled on short trips or between fuelstops.

Keep track of your odometer readingand check the maintenance scheduleregularly for required services.Increased wear or damage to certainparts can result from failure toperform required services at theproper mileage intervals.

CAUTION

46


5-9

HIGH ENGINE COOLANTTEMPERATURE WARNINGLIGHT (Red Color)

When the ignition switch is turned to the“ON” position, this light comes on briefly soyou can check that the light is working. Ifthis light blinks while driving, it means theengine is running hot. Avoid driving condi-tions that may lead to actual overheating.If the light stays on without blinking, thenthe engine is overheating. Follow the in-structions in the “If the Engine Over heats”of “EMERGENCY SERVICE” section.

Continuing to drive the vehicle whenengine overheating is indicated canresult in severe engine damage.

CAUTION

76G-05-019

FUEL GAUGE

When the ignition switch is in the “ON”position, this gauge gives an approximateindication of the amount of fuel in the fueltank. “F” stands for full and “E” stands forempty.

When the fuel meter indicator shows onlyone segment to “E”, refill the tank as soonas possible.

Note:If the last segment blinks, it means that thefuel tank is almost empty.

Note:The fuel level indicator varies depending onroad conditions (for example, slope orcurve) and driving conditions because offuel moving in the tank.

76G-05-018

The tachometer indicates engine speedin revolutions per minute.

76G-05-013C

Never drive with the engine speed in-dicator in the red zone (1) or severeengine damage can result.When downshifting to a lower gear,make sure not to operate with exces-sive revolution speeds of the engine.Refer to “Downshifting maximum allow-able speeds” in the “OPERATINGYOUR VEHICLE” section.

CAUTION

TACHOMETER (if equipped)

47


5-10

Vehicle load Switch PositionCondition

Driver only 0

Driver + 1 passenger 0(in front seat)

Driver + 3 passenger 1No cargo

Driver + 3 passenger 2Cargo added

Driver + full cargo 3

Dummy 4

Level the headlight beam according to theload condition of your vehicle by turning thisswitch. The chart shows the appropriateswitch position for different vehicle-loadconditions.

HEADLIGHT LEVELING SWITCH

76G-05-023

To open the glove box, pull the latch lever.To close it, push the lid until it latchessecurely.

Never drive with the glove box lidopen. It could cause injury if anaccident occurs.

wwwww WARNING

76G-05-022

GLOVE BOX

48


HEATING SYSTEM (if equipped)

5-11

a. Windscreen defroster outletb. Side defroster outletc. Side outletd. Center outlete. Floor outlet

The heating system provides heating,demisting, and ventilation.

76G-05-024

76G-05-025

76G-05-026

TYPE-1 (ALTO)


49


Description of Controls (if equipped)Function Lever/Knob 1: This lever/knob isused to select one of the functionsdescribed below:

VENTILATION 2: Temperature-controlled air comes out of thecenter and side air outlets.

BI-LEVEL 3 : Temperature-controlled air comes out of thefloor outlets and cooler air comesout of the center and side outlets.When the temperature controllever is in the fully “COOL”position or fully “HOT” position,however, the air from the flooroutlets and the air from the centerand side outlets will be the sametemperature.

HEAT 4: Temperature-controlledair comes out of the floor outlets.

HEAT & DEFROST 5 : Temp-erature-controlled air comes out ofthe floor outlets, the windscreendefroster outlets, and the sidedefroster outlets.

DEFROST 6 : Temperature-controlled air comes out of thewindscreen defroster outlets andthe side defroster outlets.

Air Intake Lever/Knob 7: This lever/knobis used to select between circulating outsideair (FRESH AIR) or recirculating inside air(RECIRCULATED AIR).

Temperature Control Lever/Knob 8 :(if equipped) This lever /knob is used tocontrol the temperature of the air thatcomes out of the air outlets.

Fan switch 9: This switch is used to turnon the fan and to select fan speed. Fanswitch has different speed options:-For Type-1 (Alto)Four positions-OFF, LOW, MEDIUM andHIGH.For Type-2 (Alto / Alto K10)Five Positions-OFF, LOW, MEDIUM LOW,MEDIUM HIGH and HIGH.

SYSTEM OPERATING INSTRUCTIONS

5-12

76G-05-032

76G-05-031

76G-05-027

76G-05-028

76G-05-029

76G-05-03076G-05-033

TYPE-1 (ALTO)


50

76G-74E

Natural VentilationMove the function lever/knob to"VENTILATION" and the air intake lever to“FRESH AIR”, the temperature controllever/knob to the desired temperatureposition, and the fan switch to “OFF”. Freshair will flow through the vehicle when it ismoving.

Forced VentilationThe lever/knob settings are the same as fornatural ventilation except you move the fanswitch to a position other than “OFF”.

5-13

INSTRUMENT PANEL

76G-05-034

76G-05-035

TYPE-1 (ALTO)

TYPE-2 (ALTO/ALTO K10)

51


Normal Heating (Using outside air)Move the function lever/knob to “HEAT” andthe air intake lever to “FRESH AIR”, thetemperature control lever/knob to the desiredtemperature position, and the fan switch tothe desired fan speed position. Moving thefan switch to a higher fan speed positionincreases heating efficiency.

5-14

76G-05-036 76G-05-038

76G-05-037 76G-05-039

TYPE-1 (ALTO)


TYPE-1 (ALTO)


52

76G-74E

Quick Heating (Using recirculated air)The lever/knob settings are the same as fornormal heating except you move the airintake lever to “RECIRCULATED AIR”. Ifyou use this heating method for anextended period of time, the air in thevehicle can become contaminated and thewindows can become misty. Therefore, usethis method only for quick heating andchange to the normal heating method assoon as possible.

Cool Face/Warm FeetMove the function lever/knob to “BI-LEVEL”and the air intake lever to “FRESH AIR”,the temperature control lever/knob to thedesired temperature position, and the fanswitch to the desired fan speed position.Unless the temperature control lever is inthe fully “COOL” position or fully “HOT”position, the air that comes out of the centerand side outlets will be cooler than the airthat comes out of the floor outlets.

5-15

INSTRUMENT PANEL

76G-05-040

76G-05-041

TYPE-1 (ALTO)

TYPE-2 (ALTO/ALTO K10)

53


Defrosting/Warm FeetMove the function lever/knob to “HEAT &DEFROST” and the air intake lever to“FRESH AIR”, the temperature control lever/knob to the desired temperature position,and the fan switch to “HIGH”. When thewindscreen has become clear, move the fanswitch to the desired fan speed position.

5-16

76G-05-042 76G-05-044

76G-05-043 76G-05-045

TYPE-1 (ALTO)


TYPE-1 (ALTO)


54

76G-74E

DefrostingMove the function lever/knob to “DEFROST”and the air intake lever to “FRESH AIR”,the temperature control lever/knob to thedesired temperature position, and the fanswitch to “HIGH” Moving the temperaturecontrol lever/knob to a higher temperatureposition increases defrosting efficiency.When the windscreen has become clear,move the fan switch to the desired fanspeed position.

AIR CONDITIONING SYSTEM(if equipped)

If your vehicle is equipped with airconditioner, it has an A/C button located onthe heater control panel. The air conditioningsystem can be used to provide cooling anddehumidifying, as described below. To turnon the air conditioning system, push in theA/C button and move the fan switch to aposition other than “OFF”. An indicator lightwill come on when the air conditioningsystem is on. To turn off the air conditioningsystem, push the A/C button again.

During operation of the air conditioner, youmay notice slight changes in engine speed.These changes are normal, the system isdesigned so that the compressor turns onor off to maintain the desired temperature.Less operation of the compressor results inbetter fuel economy.

5-17

INSTRUMENT PANEL

76G-05-047

(ALTO / ALTO K10)

SYSTEM OPERATING INSTRUCTIONS

Normal Cooling (using outside air)Push in the A/C button, move the functionlever/knob to "VENTILATION", the airintake lever to “FRESH AIR”, thetemperature control lever/knob to the“COOL” position, and the fan switch to thedesired fan speed position. Moving the fanswitch to a higher fan speed positionincreases cooling efficiency.

If the ambient temperature is high enoughto cause insufficient cooling, use the "QuickCooling" as following.

76G-05-049

(ALTO / ALTO K10)

55


5-18

76G-05-051

(ALTO / ALTO K10)

Quick Cooling (Using recirculated air)The lever/knob settings are the same as fornormal cooling except you move the airintake lever to “RECIRCULATED AIR”. Ifyou use this cooling method for a extendedperiod of time, the air in the vehicle canbecome contaminated. Therefore, youshould occasionally move the air intakelever to “FRESH AIR”.

NOTE:If your vehicle has been left in the sun withthe windows closed, it will cool faster if youopen the windows briefly while you operatethe air conditioner with the air intake leverat “FRESH AIR” and the fan at high speed.

DehumidifyingPush in the A/C button, move the functionlever/knob to the desired function position,the air intake lever to “FRESH AIR”, thetemperature control lever/knob to the desiredtemperature position, and the fan switch tothe desired fan speed position.

NOTE:Because the air conditioner dehumidifies theair, turning it on will help keep the windowsclear, even when blowing heated air usingthe DEMIST or HEATER & DEMISTfunctions.

76G-05-053

(ALTO / ALTO K10)MaintenanceIf you do not use the air conditioner for along period, such as during winter, it maynot give the best performance when youstart using it again. To help maintain op-timum performance and durability of your airconditioner, it needs to be run periodically.Operate the air conditioner at least once amonth for one minute with the engine idling.This circulates the refrigerant and oil andhelps protect the internal components.

Note:Your vehicle uses the air conditioning re-frigerant HFC-134a, commonly called “R-134a”. Only R-134a should be used in yourvehicle.

CAUTIONUsing the wrong refrigerant may dam-age your air conditioning system. UseR-134a only. Do not mix or replace theR-134a with other refrigerants.

56

76G-74E

MEMO

57

76G-74E OTHER CONTROLS AND EQUIPMENT

6

OTHER CONTROLS AND EQUIPMENT

Parking Brake Lever .......................................................................................... 6-1

Pedals ................................................................................................................... 6-2

Gear Lever ........................................................................................................... 6-3

Fuel Filler Cap .................................................................................................... 6-3

Folding Rear Seats ............................................................................................ 6-5

Sun Visor ............................................................................................................. 6-5

Interior Light Switch .......................................................................................... 6-6

Assist Grips ........................................................................................................ 6-6

Bonnet ................................................................................................................... 6-6

Frame Hooks (if equipped) .............................................................................. 6-7

Cup Holder (if equipped) ................................................................................. 6-8

Tyre Changing Tools ......................................................................................... 6-8

High Mount Stop Lamp .................................................................................... 6-9

58

76G-74E

PARKING BRAKE LEVER

• Never drive your vehicle with theparking brake on: rear brakeeffectiveness can be reduced fromover heating, brake life may beshortened, or permanent brakedamage may result.

• If the parking brake does not holdthe vehicle securely or does notfully release, have your vehicleinspected immediately by anauthorized MARUTI SUZUKI dealer.

Always apply the parking brake fullybefore leaving your vehicle or it maymove, causing injury or damage.When parking, make sure the gearshift lever for manual transmission isleft in first gear or reverse. Remember,even though the transmission is ingear, you must always apply theparking brake fully.

The parking brake lever is located betweenthe seats. To apply the parking brake, holdthe brake pedal down and pull the parkingbrake lever all the way up.

To release the parking brake, hold the brakepedal down, pull up slightly on the parkingbrake lever, push the button on the end ofthe lever with your thumb, and lower thelever to its original position.

wwwww WARNING

6-1

wwwww WARNING


76G-06-001 76G-06-002

59

76G-74E

PEDALS

6-2

Clutch Pedal 11111The clutch pedal is used to disengage thedrive to the wheels when starting theengine, stopping, or shifting the transmissionlever. Depressing the pedal disengages theclutch.

Do not drive with your foot resting onthe clutch pedal. It could result inexcessive clutch wear, clutch damage,or unexpected loss of engine braking.

Brake Pedal 22222Your MARUTI SUZUKI vehicle is equippedwith front disc brakes and rear drum brakes.Depressing the brake pedal applies bothsets of brakes.

You may hear occasional brake squealwhen you apply the brakes. This is anormal condition caused by environmentalfactors such as cold, wet, snow, etc.

If brake squeal is excessive andoccurs each time the brakes areapplied, you should have the brakeschecked by your MARUTI SUZUKIdealer.

wwwww WARNING

CAUTION

wwwww WARNING


Do not “ride” the brakes by applyingthem continuously or resting your footon the pedal. This will result inoverheating of the brakes which couldcause unpredictable braking action,longer stopping distances, orpermanent brake damage.

Accelerator Pedal 33333This pedal controls the speed of theengine. Depressing the accelerator pedalincreases power output and speed.

76G-06-003

60

76G-74E

FUEL FILLER CAP

6-3

The fuel filler cap is located on the left rearside of the vehicle. The fuel filler lid can beunlocked by pulling up the opener lever (ifequipped) located on the outboard side ofthe driver’s seat and locked by simplyclosing the lid.

wwwww WARNING


wwwww WARNING

GEAR LEVER

Your vehicle is equipped with a manualtransmission. The gear change pattern formanual transmission is shown in theillustration. For details on how to use thetransmission, refer to USING THETRANSMISSION in the OPERATING YOURVEHICLE section.

76G-06-004 76G-06-005

MANUAL TRANSMISSIONALTO

76G-06-004A

ALTO K10


Remove the fuel filler cap slowly. Thefuel may be under pressure and mayspray out, causing injury.

Petrol is extremely flammable. Do notsmoke when refuelling, and makesure there are no open flames orsparks in the area.

61

76G-74E

6-4


If you need to replace the fuel cap,use only a cap specified for yourmodel. Using an improper fuel capcan cause a serious malfunction ofthe fuel system. You can get thecorrect replacement cap from yourMARUTI SUZUKI dealer.

The fuel tank filler cap has a "screw-onratcheting type" feature.

• To remove - turn the cap counter clock-wise. Turn the cap slowly to allow anyresidual pressure to escape.

• To install - turn the cap clockwise andtighten it securely until a "ratcheting"(clicking) sound is heard. The"ratcheting" sound indicates that the capis on properly.

CAUTION

76G-06-007 76G-06-008

The fuel filler cap is located on the left rearside of the vehicle. To unlock the fuel fillerlid, turn the key clockwise. To lock turn thekey anticlockwise.

76G-06-006

TYPE-2 (ALTO) EXAMPLE EXAMPLE

62

76G-74E

6-5


The rear seats of your vehicle can be foldedforward to provide additional luggage space.

To fold the rear seats forward, pull up thetwo lock knobs (1 and 2) on top of theseat simultaneously and fold the seatbackforward. To raise the seatback lift it up andpush it back until it locks into place.

When returning a rear seat to thenormal position, make sure thatmovement of the seatback isunobstructed and the seatback issecurely latched.

wwwww WARNING

76G-06-011

EXAMPLE

Luggage or other cargo should bestowed in the luggage compartmentwith the rear seat in an uprightposition, whenever possible. If youneed to carry cargo in the passengercompartment with the rear seat backfolded forward, be sure to secure thecargo or it may be thrown about,causing injury. Never pile cargo higherthan the seatbacks.

wwwww WARNING

SUN VISOR

The sun visor(s) can be pulled down toblock glare coming through the wind screen,or they can be unhooked and turned to theside to block glare coming through the sidewindow.

When unhooking and hooking a sunvisor, be sure to handle it by the hardplastic parts or the sun visor can bedamaged.

CAUTION

76G-06-012

FOLDING REAR SEATS

63

76G-74E

6-6


INTERIOR LIGHT SWITCH

This light switch has three positions whichfunction as described below:1 The light comes on and stays on

regardless of whether the door is openor closed.

2 The light comes on when the door isopened.

3 The light remains off even when thedoor is opened.

NOTE:Only front door(s) are involved in lightingoperation of the interior light(s).

76G-06-013

ASSIST GRIPS

Assist grips are provided for passengerconvenience.

Do not hang items on the assist grips.They could obstruct the driver’s view,resulting in an accident, or could bethrown about in an accident or abruptmanoeuvre, causing injury.

wwwww WARNING

BONNET

To open the bonnet:

1) Pull the bonnet release handle locatedon the outboard side of the driver’s sideof the instrument panel. This willdisengage the bonnet lock halfway.

76G-06-014 76G-06-015

EXAMPLE

64

76G-74E

6-7


2) Push the under-bonnet release leversideways with your finger, as shown inthe illustration. While pushing the lever,lift up the bonnet.

76G-06-016

3) Continue to lift up the bonnet until it ishigh enough to support with the proprod.

Make sure the bonnet is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.

wwwww WARNING

FRAME HOOKS (If equipped)

wwwww WARNING

Hooks are provided in both the front andrear of the vehicle for use in emergencysituations. To tow your vehicle on the roador highway, follow the instruction of"TOWING" in "EMERGENCY SERVICE"section.

The shipping hook is provided on the rearof the vehicle for shipping use. Do not usethe shipping hook for other than shippingpurpose.

76G-06-017 76G-06-018

EXAMPLE EXAMPLE EXAMPLE

Do not use these hooks to tow (or betowed by) another vehicle on the roador highway except in emergencysituations.

65

76G-74E

6-8


76G-06-019

CUP HOLDER (if equipped)

wwwww WARNING

The cup holder is provided in the centerconsole (if equipped).

Do not use the cup holder to holdcups containing hot liquids, or objectsother than cups. Objects in the cupholder may be thrown about during asudden stop or impact, and couldcause personal injury.

TYRE CHANGING TOOLS

The jack is stowed in the luggagecompartment behind the rear seat.

To remove the jack, turn its shaftcounterclockwise and pull the jack out of thestorage bracket. To stow the jack, place itin the storage bracket and turn the shaftclockwise until the jack is securely held inplace.

NOTE:If it is hard to loosen the bolt that securesthe spare tyre, use the jack handle shaft asillustrated.

76G-06-020 76G-06-021

Example

66

76G-74E

6-9


76G-06-022

76G-06-023

The jack should be used only tochange wheels. It is important to readthe jacking instructions in theEMERGENCY SERVICE section of thismanual before attempting to use thejack.

After using the jack crank and wheelwrench, be sure to stow themsecurely or they can cause injury if anaccident occurs.

wwwww WARNING

wwwww WARNING

HIGH MOUNT STOP LAMP

76G-06-024 76G-06-025

ALTO

76G-06-025A

ALTO K10

67

76G-74E

6-10


High mount stop lamp is provided with yourvehicle and is fitted on back door. The stoplamp will glow as when the brake pedal willbe depressed.

To change the bulb of the stop lamp,remove the clips at both sides of the cover,by pressing the inner pin inside so that theclip gets loose and remove the bulb onturning it anticlockwise.

There is one bulb in high mount stop lamp.

68

76G-74E

MEMO

6-11

69

76G-74E OPERATING YOUR VEHICLE

7

OPERATING YOUR VEHICLE

Exhaust Gas Warning ....................................................................................... 7-1

Daily Inspection Checklist ................................................................................ 7-1

Starting the Engine ........................................................................................... 7-2

Using the Transmission.................................................................................... 7-3

Braking ................................................................................................................. 7-4

Running-in ............................................................................................................ 7-5

Catalytic Converter ............................................................................................ 7-5

Improving Fuel Economy ................................................................................. 7-6

Trailer Towing ..................................................................................................... 7-7

70

76G-74E

EXHAUST GAS WARNING

with the engine running, make surethe air intake lever is set to “FRESHAIR” and the fan is at high speed.

• Avoid operating the vehicle with therearend door open. If it is necessaryto operate the vehicle with therearend door open, make sure allthe windows are closed and the fanis at high speed with the air intakelever set to "FRESH AIR".

• To allow proper operation of yourvehicle’s ventilation system, keepthe air inlet grille in front of thewindscreen clear of snow, leaves, orother obstructions at all times.

• Keep the exhaust tailpipe area clearof snow and other material to helpreduce the buildup of exhaust gasesunder the vehicle. This isparticularly important when parkedin blizzard conditions.

• Have the exhaust system inspectedperiodically for damage and leaks.Any damage or leaks should berepaired immediately.

DAILY INSPECTION CHECKLIST

wwwww WARNING

7-1

wwwww WARNING

Before driving:1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.2) Check the tyres.3) Look for fluid and oil leaks.

NOTE:It is normal for water to drip from the airconditioning system after use.

4) Adjust the seat/head restraint.5) Check the brake pedal and the parking

brake lever.6) Adjust the mirrors.7) Make sure that you and passengers

have properly fastened your seat belts.8) Make sure that all warning lights come

on as the key is turned to the “ON” or“START” position.

9) Check all gauges.10) Make sure that the brake fluid level

warning light is off when the parkingbrake is released with the enginerunning.


Avoid breathing exhaust gases.Exhaust gases contain carbonmonoxide, a potentially lethal gas thatis colourless and odourless. Sincecarbon monoxide is difficult to detectby itself, be sure to take the followingprecautions to help prevent carbonmonoxide from entering your vehicle.• Do not leave the engine running in

garages or other confined areas.• Do not park with the engine running

for a long period of time, even in anopen area. If it is necessary to sitfor a short time in a parked vehicle

VV VVV

VVVV V

76G-07-001

76G-07-002

71

76G-74E

Before starting the engine:1) Make sure the parking brake is applied

fully.2) Manual Transmission - Shift into “N”

(neutral) and depress the clutch pedal allthe way to the floor. Hold it while startingthe engine.

Make sure that the parking brake isapplied fully and the transmission isin Neutral before attempting to startthe engine.

• Stop turning the starter immediatelyafter the engine has started or thestarter system can be damaged.

• Do not crank the engine for morethan 15 seconds at a time. If theengine doesn’t start on the first try,wait about 15 seconds before tryingagain.

7-2

STARTING THE ENGINE

wwwww WARNING


Once a week, or each time you fill your fueltank, perform the following under-bonnetchecks:

1) Engine oil level.2) Coolant level.3) Brake fluid level.4) Windscreen washer fluid level.5) Battery solution level.6) Bonnet latch operation.

Pull the bonnet release handle inside thevehicle. Make sure that you can notopen the hood all the way withoutreleasing the secondary latch. Be sureto close the hood securely after checkingfor proper operation. See "All Latches,Hinges & Locks" of "PERIODICMAINTENANCE SCHEDULE" in the"INSPECTION AND MAINTENANCE"section for lubrication schedule.

Make sure the bonnet is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.

wwwww WARNING

Starting a Cold EngineEngine which is started after 6 hours shouldbe treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,crank the engine by turning the ignitionkey to “START”. Release the key whenthe engine starts.

• If the engine does not start after 15seconds of cranking, wait about 15seconds, then press down theaccelerator pedal to 1/3 of its travel andtry cranking the engine again. Releasethe key and accelerator pedal when theengine starts.

• If the engine still does not start, tryholding the accelerator pedal all the wayto the floor while cranking. This shouldclear the engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for “Starting aCold Engine”.

CAUTION

72

76G-74E

7-3


wwwww WARNING

CAUTION

Starting offTo start off, depress and maintain pressureupon the clutch pedal and change into 1stgear. After releasing the parking brake,

GEAR MAXIMUM SPEED

First 37 km/h

Second 66 km/h

Third 98 km/h

Fourth Top Speed

Fifth Top Speed

USING THE TRANSMISSIONMANUAL TRANSMISSION

76G-07-003

76G-07-003A

• To help avoid clutch damage, do notuse the clutch pedal as a footrest whiledriving or use the clutch to keep thevehicle stationary on a hill. Depress theclutch fully when changing gear.

• When changing gears or starting off,do not race the engine. Racing theengine can shorten engine life andprevent smooth operation.

• Reduce your speed and change down toa lower gear before going down a longor steep hill. A lower gear will allow theengine to provide braking. Avoid ridingthe brakes or they may overheat, result-ing in brake failure.

• When driving on slippery roads, be sureto slow down before changing down.Excessive and or sudden changes inengine speed may cause loss of traction,which could cause you to lose control.

• Make sure that the vehicle is completelystationary before you change into re-verse.

gradually release the clutch. When you heara change in the engine’s sound (speed),gently apply pressure to the accelerator tokeep the engine sound (speed) constant whilstcontinuing to gradually release the clutch.

Gear changingAll forward gears are synchronized, whichprovides for quiet, easy changing. Alwaysdepress the clutch pedal fully before changinggears. The following table shows themaximum allowable speed for each gear.

ALTO

ALTO K10

GEAR MAXIMUM SPEED

First 43 km/h

Second 80 km/h

Third 119 km/h

Fourth Top Speed

Fifth Top Speed

ALTO

ALTO K10

73

76G-74E

7-4


BRAKINGwwwww WARNING

The distance needed to bring any vehicleto a halt increases with the speed of thevehicle. The braking distance needed, forexample, at 60 km/h will be approximately4 times greater than the braking distanceneeded at 30 km/h. Start to brake thevehicle when there is plenty of distancebetween your vehicle and the stoppingpoint, and slow down gradually.

If water gets into the brake drums, brakeperformance may become poor andunpredictable. After driving through wateror washing the underside of the vehicle,test the brakes while driving at a slowspeed to see if they have maintained theirnormal effectiveness. If the brakes areless effective than normal, dry them byrepeatedly applying the brakes whiledriving slowly until the brakes haveregained their normal effectiveness.

Servo assisted brakesYour vehicle has servo assisted brakeswhich works with the assistance of enginevacuum.

Do not switch off the engine while vehicleis in motion, for example, while drivingdown a hill as this will cause loss ofvacuum assistance leading to reduction ofbraking efficiency substantially.

If servo assistance is lost due to a stalledengine or other failures, the system is stillfully operational on reserve power and youcan bring the vehicle to a complete stop bypressing the brake pedal once and holdingit down. The reserve power is partly usedup each time you depress the brake pedal.Apply smooth and constant pressure to thepedal. Do not pump the pedal.

wwwww WARNING

76G-07-004

To avoid shock loads on the driveline andconsequent driveline breakage, it is stronglyrecommended not to exceed the followingspeeds when downshifting:-

GEAR MAXIMUM SPEED

2nd to 1st 9 km/h

3rd to 2nd 33 km/h

4th to 3rd 49 km/h

5th to 4th Any Speed OK

ALTO

ALTO K10

GEAR MAXIMUM SPEED

2nd to 1st 10 km/h

3rd to 2nd 37 km/h

4th to 3rd 55 km/h

5th to 4th Any Speed OK

74

76G-74E

7-5


RUNNING-IN

The future performance and reliabilityof the engine depends on the careand restraint exercised during its earlylife. It is especially important toobserve the following precautionsduring the initial 1000 km of vehicleoperation.• After starting, do not race the

engine. Warm it up gradually.• Avoid prolonged vehicle operation at

a constant speed. Moving parts willbed in better if you vary your speed.

• Do not exceed 100 km/h.• Start off from a stop slowly. Avoid

full throttle starts.• If possible, avoid hard braking,

especially during the first 300 kmof driving.

• Do not drive slowly with thetransmission in a high gear.

• Drive the vehicle at moderate enginespeeds.

CAUTIONEven without reserve power in thebrake system, you can still stop thevehicle by pressing the brake pedalharder than normally required.However, the stopping distance maybe longer.

On loose surface where the wheelscan easily loose traction (such asgravel, etc.), the stopping distancerequired for your vehicle may begreater than for a comparable vehiclewith a conventional brake system.Allow for extra stopping distancewhen driving on loose surfaces.

wwwww WARNING

wwwww WARNING

CATALYTIC CONVERTER

The purpose of the catalytic converterinstalled on your vehicle is to convertexhaust pollutants to harmless water vapour,carbon dioxide, and nitrogen. Use of leadedfuel in vehicles equipped with catalyticconverters is prohibited, because leaddeactivates the pollutant-reducing compo-nents of the catalyst system.

It is very important to keep the engineproperly tuned. Engine misfiring, which canresult from an improperly tuned engine, maycause overheating of the catalyst. This mayresult in permanent heat damage to thecatalyst and other vehicle components.

76G-07-005

75

76G-74E

7-6


Be careful where you park and drive;the catalytic converter and otherexhaust components can get very hot.As with any vehicle, do not park oroperate this vehicle in areas wherecombustible materials such as drygrass or leaves can come in contactwith a hot exhaust system.

wwwww WARNING

To minimize the possibility of catalystor other vehicle damage:• Maintain the engine in the proper

operating condition.• In the event of an engine

malfunction, particularly oneinvolving engine misfire or otherapparent loss of performance, havethe vehicle serviced promptly.

• Do not turn off the engine orinterrupt the ignition when thetransmission is in gear and thevehicle is in motion.

• Do not try to start the engine bypushing or towing the vehicle, orcoasting down a hill.

• Do not idle the engine with anyspark plug wires disconnected orremoved, such as during diagnostictesting.

• Do not idle the vehicle forprolonged periods if idling seemsrough or there are othermalfunctions.

• Do not allow the fuel tank to getnear the empty level.

CAUTION

IMPROVING FUEL ECONOMY

The following instructions will help youimprove fuel economy.

Avoid excessive idling:If you are to wait for more than a minutewhile you are parked, stop the engine andstart it again later. When warming up a coldengine, allow the engine to idle for sometime.

Avoid “fast” starts:Fast starts away from lights or stop signswill consume fuel unnecessarily and shortenengine life. Start off slowly.

Avoid unnecessary stops:Avoid unnecessary deceleration andstopping. Try to maintain a slow, steadyspeed whenever possible. Slowing downand then accelerating again uses more fuel.

Keep a steady cruising speed:Keep as constant a speed as road andtraffic conditions will permit.

76G-07-006

76

76G-74E

7-7

TRAILER TOWING

Your MARUTI SUZUKI is designed to carrypeople and a normal amount of cargo, notto tow a trailer. Maruti does not recommendyou use your vehicle to tow a trailer. Towinga trailer can adversely affect handling,durability, and fuel economy.

Keep the air cleaner clean:A dirty air cleaner will cause the fuel systemto supply too much fuel to the engine forthe amount of air being supplied. The resultis waste of fuel due to incompletecombustion.

Keep weight to a minimum:The heavier the load, the more fuel thevehicle consumes. Take out any luggage orcargo when it is not necessary.

Keep tyre pressures correct:Under-inflation of the tyres can waste fueldue to increased running resistance of thetyres. Keep your tyres inflated to the correctpressure shown on the label on the driver’sside door or door lock pillar.


76G-07-007

77

76G-74E DRIVING TIPS AND SAFE DRIVING

8

DRIVING TIPS AND SAFE DRIVING

High Speed Driving ........................................................................................... 8-1

Driving on Hills .................................................................................................. 8-1

Driving on Slippery Roads .............................................................................. 8-1

Driving on Wet Roads ...................................................................................... 8-2

Do’s and Don’ts for Safe Driving .................................................................. 8-3

78

76G-74E

• Wear Your Seat Belts at All Times.The driver and passengers shouldbe properly restrained at all times,using the seatbelts provided. Referto the “SEATBELTS” section forinstructions on proper use of theseat belts.

• Never drive while under theinfluence of alcohol or other drugs.Alcohol and drugs can seriouslyimpair your ability to drive safely,greatly increasing the risk of injuryto yourself and others. You shouldalso avoid driving when you aretired, sick, irritated, or under stress.

HIGH-SPEED DRIVING

• When driving down a hill, the engineshould be used for braking by shifting tonext lower gear.

Try not to hold the brake pedal downtoo long or too often while goingdown a steep or long hill. This couldcause the brakes to overheat,resulting in reduced braking efficiency.Failure to take this precaution couldresult in loss of vehicle control.

When descending a down hill, NEVERturn the ignition key to the “OFF”position. Emission control systemdamage may result.

DRIVING ON SLIPPERY ROADSUnder wet road conditions you should driveat a lower speed than on dry roads due topossible slippage of tyres during braking.When driving on icy, snowcovered, ormuddy roads, reduce your speed and avoidsudden acceleration, abrupt braking, orsharp steering movements.

When driving at a high-speed, pay attentionto the following:• Stopping distance progressively increases

with vehicle speed. Apply the brakes farenough ahead of the stopping point toallow for the extra stopping distance.

• On rainy days, “Aquaplaning” can occur.“Aquaplaning” is the loss of directcontact between the road surface andthe vehicle’s tyres due to a water filmforming between them. Steering orbraking the vehicle while “Aquaplaning”can be very difficult, and loss of controlcan occur. Keep speed down when theroad surface is wet.

• At high speeds, the vehicle may beaffected by side winds. Therefore, reducespeed and be prepared for unexpectedbuffeting, which can occur at the exitsof tunnels, when passing by a cut of ahill, or when being overtaken by largevehicles, etc.

DRIVING ON HILLS• When climbing steep hills, the vehicle

may begin to slow down and show alack of power. If this happens, youshould change to a lower gear so thatthe engine will again be operating in itsnormal power range. Change rapidly toprevent the vehicle from losingmomentum.

wwwww WARNING

wwwww WARNING

CAUTION

8-1


76G-08-001

79

76G-74E

Snow ChainsIf you must use snow chains to increase tyretraction, observe the following precautions:• Use cable type chains.• Choose a safe place away from traffic

to install the chains.• When installing the chains carefully

follow the manufacturer’s instructions.• Install the chains on the front tyres.• With the chains on, drive only at slow

and moderate speeds.• If the chain hits the vehicle body while

driving, stop at a safe place andretighten it as soon as possible.

• If snow and/or ice on the roaddisappear, remove the chains as soonas possible.

• If Your Vehicle Gets StuckIf your vehicle gets stuck in snow, mud,or sand, follow the directions below:

1) Change back and forth between aforward range (or first gear for manualtransmission) and reverse. This willcreate a rocking motion which may giveyou enough momentum to free thevehicle. Press gently on the acceleratorto keep wheel spin to a minimum.Remove your foot from the acceleratorwhile changing gear.Do not race the engine. Excessive wheelspin will cause the tyres to dig deeper,making it more difficult to free thevehicle.

2) If your vehicle remains stuck after a fewminutes of rocking, get another vehicleto pull you out.

Do not allow anyone to stand near thevehicle when you are rocking it, anddo not spin the wheels faster than anindicated 40 km/h on the speedometer.Personal injury and/or vehicle damagemay result from spinning the wheelstoo fast.

Do not continue rocking the vehiclefor more than a few minutes.Prolonged rocking can cause engineoverheating or transmission damage.

• Make sure your tyres are in goodcondition and always maintain thespecified tyre pressure. Refer to“TYRES” in the “INSPECTION ANDMAINTENANCE” section for details.

• Do not use tyres other than thosespecified by MARUTI SUZUKI. Neveruse different sizes or types of tyreson the front and rear wheels. Forinformation regarding the specifiedtyres, refer to the “SPECI-FICATIONS” section.

• Never use oversized tyres or specialshock absorbers and springs toraise (jack up) your vehicle. This willchange the handling characteristics.

• After driving through water, test thebrakes while driving at a slow speedto see if they have maintained theirnormal effectiveness. If the brakesare less effective than normal, drythem by repeatedly applying thebrakes while driving slowly until thebrakes have regained their normaleffectiveness.

wwwww WARNING

CAUTION

8-2

wwwww WARNING


DRIVING ON WET ROADS

• When driving on wet roads, avoiddriving through large amount ofstanding water on the road. Largeamount of water entering the enginecompartment may cause damage tothe engine and or electricalcomponents.

• If stuck in deep water, do not starttill water level drops.

• Water is incompressible substance,water inside engine is harmful to theengine.

CAUTION

80

76G-74E

DO’S AND DON’TS FOR SAFEDRIVINGExercise care in handling your vehicle. Beconscious of not only your own safety butalso the safety of others on the road, andthus enjoy the best and most comfortabledriving experience.

This section contains basic rules for safedriving. Read it carefully for goodunderstanding of the content so that youcan enjoy safe and pleasant driving in yourMaruti Suzuki vehicle.

Starting1. Adjust the driver’s seat for the proper

driving posture.

2. Adjust the rear view mirror so as toobtain the best possible rear view.

3. Before moving off, look forward and backto confirm safety.

4. Don’t start quickly, for it is dangerousand wastes fuel.

General driving1. Be sure to stop before the stop light and

stop sign. When moving into theintersection without any traffic lights orsigns, drive slowly to confirm safety.

8-3


2. Always follow other vehicles at a safedistance in order to prevent a rear-endcollision, should the vehicle ahead makea sudden stop.

3. Turn ON the turn signal at least 30meters before making a turn or changingthe lane so as not to be hit from behind.

4. Before entering a corner, decelerate toa safe speed. Don’t apply brakes duringcornering, or a cornering skid may occur.

5. When overtaking other vehicles, watchout for the oncoming vehicle andcarefully confirm the safety.

6. Don’t attempt zigzag driving which willhinder your control over the vehicle andcause an accident.

76G-08-002 76G-08-003

81

76G-74E

especially dangerous when the tyres areworn, for they allow a larger skid.Use foot brake in three stages(1) Warn the vehicle behind you(2) Gradually apply the brake.(3) Bring the vehicle to a halt.

3. When driving on a downhill, try not toapply the brake but use the enginebrake effectively. Overuse of thefootbrake may result in total brakefailure.

4. Avoid reckless high speed driving and tryto drive at a safe speed suitable for theroad conditions while maintaining aconstant speed.

5. The higher the speed, the narrower thedriver’s visual range becomes. In sucha state, it is difficult to anticipate anyhazard and the driver feels muchfatigued.

6. Never do sharp handling during highspeed driving. You will lose your controlover your vehicle.

7. When overtaking or changing the lanewhile driving at a high speed, keep anample vehicle-to-vehicle distance.

Long distance driving1. Be sure to perform safety checks before

starting a trip.

2. Take rest at certain intervals to preventan accident which may occur when youare sleepy or tired.

Braking1. Use the parking brake when parking

your vehicle and shift the gear shift leverinto the first gear or reverse gearposition for the sake of safety.

2. Don’t use handbraking unlessunavoidable. It causes the vehicle to skidand a rearend collision occur. It is

8-4


76G-08-004

76G-08-005 76G-08-006

82

76G-74E

Night time driving1. Drive more slowly at night than in the

daytime, for the visual range is restrictedat night.

2. Don’t overtake other vehicles at night.Darkness bothers your sense of speedand hinders your judgement on thevehicle-to-vehicle distance.

3. Don’t use the high headlight beamunless its use is inevitable. Its dazzlemay blitz the driver of the oncomingvehicle, thus causing an accident.

4. Always keep the window glasses clean.Don’t operate the windshield wiper whenthe windshield glass is dry or the wiperblade and glass may get damaged.

8-5


MARGIN FOR SAFETY

It is important to allow yourself a margin forsafety during driving so that you can copewith erroneous or unexpected driving ofother drivers. For that, observe thefollowing.

• Drive at a safe speed.• Maintain a sufficient distance between

your vehicle and the vehicle ahead.• Don’t force yourself to overtake other

vehicles.• Don’t make quick start, hard steering or

sudden stops.• Allow an ample time in the driving

schedule.• Observe traffic rules and regulations.

CONCLUSION

A perfect driver does not exist. Theendeavour of every motorist should be tostrive for perfection. Safety consciousnessnot only ensures your safety and the safetyof other road users, it also helps reduce thewear and tear on your vehicle, prolongs itslife, gives more mileage and ensures acomfortable driving experience.

Follow the do’s and don’ts listed, anddriving will never be the same again.

76G-08-007 76G-08-008

76G-08-009

83

76G-74E INSPECTION AND MAINTENANCE

9

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule ......................................................................... 9-1Alto ............................................................................................................. 9-2Alto K-10 .................................................................................................... 9-6

Drive Belt ............................................................................................................ 9-10Engine Oil and Filter .......................................................................................... 9-11Gear Oil ............................................................................................................... 9-14Engine Coolant ................................................................................................... 9-15Windscreen Washer Fluid ................................................................................. 9-18Air Cleaner .......................................................................................................... 9-18Spark Plugs ........................................................................................................ 9-19Fuel Filter Replacement .................................................................................... 9-21Brakes ................................................................................................................. 9-21Parking Brake ..................................................................................................... 9-23Steering ............................................................................................................... 9-23Clutch Pedal ....................................................................................................... 9-24Tyres .................................................................................................................. 9-24Tubeless Tyre (if equipped) .............................................................................. 9-27Battery ................................................................................................................. 9-28Fuses .................................................................................................................. 9-29Bulb Replacement .............................................................................................. 9-32Wiper Blades ...................................................................................................... 9-35

84

76G-74E

You should take extreme care whenworking on your vehicle to preventaccidental injury. Here are a fewprecautions that you should beespecially careful to observe:• Do not leave the engine running in

garages or other confined areas.• When the engine is running, keep

hands, clothing, tools, and otherobjects away from the fan and waterpump belt. Even though the fan maynot be moving, it can automaticallyturn on without warning.

• When it is necessary to do servicework with the engine running, makesure that the parking brake isapplied fully and the transmission isin Neutral.

• Do not touch ignition wires or otherignition system parts when startingthe engine or when the engine isrunning, or you could receive anelectric shock.

• Be careful not to touch a hotengine, exhaust manifold and pipes,muffler, radiator and water hoses.

• Do not allow smoking, sparks, orflames around gasoline or thebattery. Flammable fumes arepresent.

• Do not get under your vehicle if itis supported only with the portablejack provided in your vehicle.

• Be careful not to cause accidentalshort circuits between the positiveand negative battery terminals.

• Keep used oil, coolant, and otherfluids away from children and pets.Dispose of used fluids properly;never pour them on the ground, intosewers, etc.


9-1

wwwww WARNING

wwwww WARNING

VVVV V

VV VVV

PERIODIC MAINTENANCE SCHEDULE

The following table shows when regularmaintenance on your vehicle is required.This table shows in kilometres and monthswhen inspections, adjustments, lubricationand other services should be performed.

MARUTI SUZUKI recommends thatmaintenance on your MARUTI SUZUKIvehicle be performed by MARUTISUZUKI Authorised Dealer/ServiceStation.

Whenever it becomes necessary toreplace parts on your vehicle, it isrecommended that you use MARUTIGENUINE PARTS (MGP).

wwwww WARNING

CAUTION76G-09-001

85


9-2

A....Adjust. I....Inspect and correct or replace if necessary.T....Tighten to specified torque. C....Clean.R....Replace or change. O....RotateL....Lubricate.

Note:This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the sameintervals respectively.

Interval: This interval should be judged FREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COSTby odometer reading or months, km (x 1,000) 1 5 10 20 30 40 50 60 70 80whichever comes first. months 1 6 12 24 36 48 60 72 84 96

ENGINE

1. Water pump drive belt (tension, wear) A I I I I I I R A I

2. Engine coolant (level, leakage) I I I R I R I R I R

3. Engine oil (API GRADE SF, SG, SH) & Oil filter R I R R R R R R R R

4. Cooling system hoses and connections (leakage, damage) I I I I I I I I I I

5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –

6. Engine mounting (loose, damage) – – T – T – T – T –

7. Valve clearance – A – A – A – A – A

8. Camshaft timing belt (damage, wear) – – – I – I – I – I

Replace every 1,00,000 km

9. Exhaust system (noise, leakage or otherwise defective) – I – I – I – I – I

10. Positive crankcase ventilation System (Hoses, connections and valve) – I – I – I – I – I

IGNITION

1. Ignition wiring, (damage, deterioration) – – – I – I – I – I

2. Spark plugs (clean and adjust the gap) – – I R I R I R I R

3. Distributor cap and rotor (wear and deterioration)* – – – I – I – I – I

*For LX only

ALTO

86

76G-74EINSPECTION AND MAINTENANCE

9-3


FUEL

1. Air cleaner Paved-road Clean every 5,000 km. Replace every 40,000 km.

Dusty condition Clean every 2,500 km or as required. Replace every 40,000 km. More frequentreplacement if dust condition is severe.

2. Accelerator cable and Throttle shafts – I&L I&L I&L I&L I&L I&L I&L I&L I&L

3. Fuel tank cap, fuel lines & connections(leakage,damage) – I – – – I – – – I

4. Fuel filter (leakage) I I I I I R I I I R

CLUTCH AND TRANSMISSION

1. Clutch pedal (play) I I I I I I I I I I

2. Clutch slipping (dragging or excessive damage) I I I I I I I I I I

3. Manual Transmission/Transfer and Differential oil (level, leakage) I I I R I R I R I R

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage) – I I I I I I I I I

BRAKE

1. Brake fluid (level, leakage) I I I R I R I R I R

2. Brake pedal (pedal-to-wall clearance) I I I I I I I I I I

3. Parking brake lever and cable (play, damage) I I I I I I I I I I

4. a. Brake discs and pads, (wear) – I I I I I I I I I

b. Brake drums & shoes – – I I I I I I I I

5. Master cylinder and wheel cylinder or calliper (oil leakage, boot kit) I I I I I R I I I R

6. Brake hoses and pipes (leakage, damage) I I I I I I I I I I

87


9-4


WHEEL

1. Tyres (air pressure, abnormal wear, crack, rotation) I I&O I&O I&O I&O I&O I&O I&O I&O I&O

2. Wheels (damage) I I I I I I I I I I

3. Front wheel bearings (loose, damage) – I I I I I I I I I

4. Rear wheel bearings (loose, damage) – I I I I I I I I I

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage) I I I I I I I I I I

2. Suspension arms and knuckle supports (loose,damage) – I I I I I I I I I

3. Rear spring (damage) – I I I I I I I I I

4. Shock absorbers (oil leakage, damage) I I I I I I I I I I

5. All bolts and nuts (loose) – T T T T T T T T T

6. Suspension arms and Tension rods – I I I I I I I I I

STEERING

1. Steering wheel (play, loose) I I I I I I I I I I

2. All rods and arms (loose, damage, wear) I I I I I I I I I I

ELECTRICAL

1. Battery electrolyte (level, leakage) I I I I I I I I I I

2. Wiring harness connection (looseness, damage) – I I I I I I I I I

3. Lighting system (operation, stains, damage) I I I I I I I I I I

4. Horn (operation) I I I I I I I I I I

5. System voltage – I I I I I I I I I

BODY

1. All chassis bolts and nuts (tighten) – I T T T T T T T T

2. All Latches, Hinges & Locks (function) I I&L I&L I&L I&L I&L I&L I&L I&L I&L

88


9-5


ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer I I I I I I I I I I

2. Body and Chassis noise I I I I I I I I I I

AIR CONDITIONER (if equipped)

1. Check belt tension I I I I I I I I I I

2. Tighten compressor mounting bolts – T T T T T T T T T

3. Check all hose joints, tighten if necessary I I I I I I I I I I

4. Check functioning of Recirc flap I I I I I I I I I I

5. Clean condenser with low pressure water – C C C C C C C C C

6. Check belt for frayed edges, change if necessary – I I I I I I I I I

7. Check all mounting bolts – I I I I I I I I I

89

76G-74E

A....Adjust. I....Inspect and correct or replace if necessary.T....Tighten to specified torque. C....Clean.R....Replace or change. O....RotateL....Lubricate.

Note:This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals respectively.


9-6

ALTO K10

90


9-7

91


9-8

92

76G-74E

wwwww WARNINGThe rear shock absorbers are filled withhigh pressure gas. Never attempt todisassemble it or throw it into a fire.Avoid storing it near a heater or heatingdevice. When scrapping the absorber,the gas must be released from theabsorber safely. Ask your dealer forassistance.

• All maintenance should be carried out withthe ignition switch in the “OFF” positionand the car parked securely on the levelground unless otherwise specified.

• If you are in any way unsure of yourability to undertake a task, then do notstart it but contact your MARUTI SUZUKIdealer to perform the work for you.

wwwww WARNING


9-9

93


9-10

DRIVE BELT

When the engine is running, keephands, hair, clothing, tools, etc. awayfrom the fan and drive belt. Eventhough the fan may not be moving, itcan automatically turn on withoutwarning.

Water pump belt (A) 8 - 9 mm

Air conditioner belt (B) 8 - 9 mm

wwwww WARNING

76G-09-002

Make sure the drive belt tension is correct.If the belt is too loose, insufficient batterycharging, engine overheating, or excessivebelt wear can result. When you press thebelt with your thumb midway between thepulleys, the belt deflection should be withinthe specification below.

The belt should also be examined to ensurethat it is not damaged. If the belt needs tobe replaced or adjusted, have it done byyour MARUTI SUZUKI dealer.

DEF: 4.0 – 4.5 mm(0.16 – 0.18 in.)

DEF: 7 – 8 mm(0.28 – 0.31 in.)

: 100 N (10 kg, 22 lbs) pressGE: GeneratorDEF: DeflectionAC: Air conditioner compressor

GE

AC

ALTO K10ALTO

94


9-11

ENGINE OIL AND FILTER

Specified oilBe sure that the engine oil you use comesunder the API classification of SF, SG orSH. The recommended engine oil is SF20W40 (1). Select the appropriate oilviscosity according to the above chart.

Oil Level CheckIt is important to keep the engine oil at thecorrect level for proper lubrication of yourvehicle’s engine. Check the oil level with thevehicle on a level surface. The oil levelindication may be inaccurate if the vehicleis on a slope. The oil level should bechecked either before starting the engine orat least 5 minutes after stopping the engine.

Pull out the oil dipstick, wipe oil off with aclean cloth, insert the dipstick all the wayinto the engine, then remove it again. Theoil on the stick should be between theupper and lower limits shown on the stick.If the oil level indication is near the lowerlimit, add enough oil to raise the level tothe upper limit.

76G-09-003 76G-09-004

(1) Preferred

Be sure that the engine oil you use comesunder the quality classification of SG+, SL& SJ. Select the appropriate oil viscosityaccording to the above chart.

SAE 5W30 (1) is the best choice for goodfuel economy, and good starting in coldweather.

Failure to check the oil level regularlycould lead to serious engine troubledue to insufficient oil.

ALTO K10ALTO EXAMPLE

CAUTION

95


9-12

RefillingRemove the oil filler cap and pour oil slowlythrough the filler hole to bring the oil levelto the upper limit on the dipstick. Be carefulnot to overfill. Too much oil is almost asbad as too little oil. After refilling, start theengine and allow it to idle for about aminute. Stop the engine, wait for fiveminutes and check the oil level again.

Changing Engine Oil and FilterDrain the engine oil while the engine is stillwarm.1) Remove the oil filler cap.2) Place a drain pan under the drain plug.3) Using the correct spanner remove the

drain plug and drain out the engine oil.

The engine oil temperature may be highenough to burn your fingers when thedrain plug is loosened. Wait until thedrain plug is cool enough to touch withyour bare hands.

wwwww WARNING

New and used oil can be hazardous.Children and pets may be harmed byswallowing new or used oil. Keep newand used oil and used oil filters awayfrom children and pets.Continuous contact with used engineoil may cause (skin) cancer.Brief contact with used oil may irritateskin.To minimize your exposure to usedoil, wear a long-sleeve shirt andmoistureproof gloves (such asdishwashing gloves) when changingoil. If oil contacts your skin, washthoroughly with soap and water.Launder any clothing or rags if wetwith oil.Recycle or properly dispose of usedoil and filters.

4. Reinstall the drain plug and new gasket.Tighten the plug with a wrench to thespecified torque.

wwwww WARNING

76G-09-005 76G-09-006

Tightening torque for drain plug (1):35 Nm (3.5 kg-m, 25.5 lb-ft)

ALTO

ALTO K10

Tightening Torque :49± 5 N.m

96


9-13

Replace the oil filter1) Using an oil filter wrench, turn the oil

filter counterclockwise and remove it.2) Using a clean rag, wipe off the mounting

surface on the engine where the newfilter will be seated.

3) Smear a little engine oil around therubber gasket of the new oil filter.

4) Screw on the new filter by hand until thefilter gasket contacts the mountingsurface.

To tighten the oil filter properly, it isimportant to accurately identify theposition at which the filter gasketfirst contacts the mounting surface.

5. Tighten the filter specified turn from thepoint of contact with the mounting sur-face (or to the specified torque) using anoil filter wrench.Tightening torque for oil filter1 turn or14 Nm (1.4 kg-m, 10.5 lb-ft)

CAUTION

Refill with oil and check for leaks.1) Pour oil through the filler hole and install

the filler cap.For the approximate capacity of the oil,refer to the "CAPACITIES" item in the"SPECIFICATIONS" section.

2) Start the engine and look carefully forleaks at the oil filter and drain plug. Runthe engine at various speeds for at least5 minutes.

3) Stop the engine and wait for 5 minutes.Check the oil level again and add oil ifnecessary. Check for leaks again.

When replacing the oil filter, it isrecommended that you use a genuineMARUTI replacement filter.

Oil leaks from around the oil filter ordrain plug indicate incorrect installa-tion or gasket damage. If you find anyleaks or are not sure that the filterhas been properly tightened, have thevehicle inspected by your MARUTISUZUKI dealer.

CAUTION

CAUTION

CAUTION

76G-09-007 76G-09-008

To prevent oil leakage, make surethat the oil filter is tight, but do notovertighten it.

(1) Oil filter(2) 1 Turn

97


9-14

GEAR OIL

Oil filler and level plug 1Tightening torque: 21 Nm (2.1 kg-m, 15.5lb-ft)

Specified Manual Transmission oilWhen adding gear oil, use the appropriateviscosity and grade as shown in the chartbelow. We highly recommend you use APIGL-4 SAE 75W-90 (1) gear oil.

Type of oil Gear oil, API GL-4

Gear oil level checkTo check the gear oil level, use thefollowing procedure:1) Park the vehicle on a level surface with

the parking brake applied. Then, stop theengine.

2) Clean casing around oil filler plug toremove risk of any loose dirt or debrisentering oil filler plug hole. Remove theoil filler plug 1.

3) Feel the inside of the hole with yourfinger. If the oil level comes up to thebottom of the plug hole, the oil level iscorrect. If so, reinstall the plug.

4) If the oil level is low, add gear oilthrough the filler plug hole 1 until theoil level reaches the bottom of the fillerhole, then reinstall the plug.

After driving the vehicle, thetransmission oil temperature may behigh enough to burn you. Wait untilthe oil filler plug is cool enough totouch with your bare hands beforeinspecting transmission oil.

When tightening the plug, applysealing compound to the plug threadsto prevent oil leakage.

Gear oil changeSince special procedures, materials andtools are required, it is recommended thatyou trust this job to your authorizedMARUTI SUZUKI dealer.

wwwww WARNING

CAUTION

76G-09-009 76G-09-010

98


9-15

ENGINE COOLANT

76G-09-011

ALTO

76G-09-012

EXAMPLE

EXAMPLEEXAMPLE ALTO K10

EXAMPLEALTO ALTO K10

Selection of Coolant

To maintain optimum performance anddurability of your engine, use MARUTIGenuine Coolant or equivalent.This type of coolant is best for your coolingsystem as it:• Helps maintain proper engine temperature.• Gives proper protection against freezing

and boiling.• Gives proper protection against corrosion

and rust.Failure to use the proper coolant can dam-age your cooling system. Your MARUTISUZUKI authorized dealer can help youselect the proper coolant.

99


9-16

CAUTIONTo avoid damaging your cooling sys-tem:• Always use a high quality ethylene

glycol base non-silicate type cool-ant diluted with distilled water atthe correct mixture concentration.

• Make sure that the proper mix is 30/70 coolant to distilled water.Concentrations greater than 70/30coolant to distilled water will causeover heating conditions.

• Do not use straight coolant norplain water.

• Do not add extra inhibitors or addi-tives. They may not be compatiblewith your cooling system.

• Do not mix different types of basecoolants. Doing so may result inaccelerated seal wear and/or thepossibility of severe overheatingand extensive engine damage.

Coolant Level Check

Check the coolant level at the reservoirtank, not at the radiator. With the enginecool, the coolant level should be betweenthe “FULL” and “LOW” marks.

Adding Coolant

If the coolant level is below the “LOW”mark, more coolant should be added.Remove the reservoir tank cap and addcoolant until the reservoir tank level reachesthe “FULL” mark. Never fill the reservoirtank above the “FULL” mark.

CAUTION• The mixture you use should con-

tain 50% concentration of anti-freeze.

• If the lowest ambient temperaturein your area is expected to be –35°C (–31°F) or below, use higherconcentrations up to 60% followingthe instructions on the antifreezecontainer.

• When putting the cap on the reser-voir tank, line up the arrow on thecap and the arrow on the tank. Fail-ure to follow this can result in cool-ant leakage.

100

76G-74E

Coolant ReplacementTrust this job to your Maruti SuzukiAuthorised Workshop.

76G-09-013

wwwww WARNING

76G-09-014

It is dangerous to remove the radia-tor cap when the water temperatureis high, because scalding fluid andsteam may be blown out under pres-sure. Wait until the coolant tempera-ture has lowered before removing thecap.

wwwww WARNINGEngine coolant is harmful or fatal ifswallowed or inhaled. Do not drinkantifreeze or coolant solution. If swal-lowed, do not induce vomiting. Imme-diately contact a poison control centeror a physician. Avoid inhaling mist orhot vapors. If inhaled, expose yourselfto fresh air. If coolant gets in eyes,flush eyes with water and seek medi-cal attention. Wash thoroughly afterhandling. Solution can be poisonous toanimals. Keep out of the reach ofchildren and animals.

9-17


101

76G-74E

WINDSCREEN WASHER FLUID

Check that there is washer fluid in the tank.Refill it if necessary. Use a good qualitywindscreen washer fluid, diluted with wateras necessary.

Do not use “antifreeze” solution in thewindscreen washer reservoir. This canseverely impair visibility when sprayedon the windscreen, and can alsodamage your vehicle’s paint.

Damage may result if the washermotor is operated whilst the fluid orfluid nozzles are frozen or with nofluid in the washer tank.

wwwww WARNING

CAUTION

76G-09-016

AIR CLEANER

If the air cleaner is clogged with dust, therewill be greater intake resistance, resultingin decreased power output and increasedfuel consumption.

Take out the air cleaner element afterunhooking the clamps shown in theillustration. Blow off dust on air cleanerelement by compressed air. If the aircleaner element appears to be dirty, replaceit with a new one.

76G-09-017

ALTO K10


9-18

EXAMPLE ALTO EXAMPLE

EXAMPLE

102

76G-74E

The air cleaner element should bereplaced every 40,000 km. Morefrequent replacement is necessarywhen you drive under dustyconditions.

CAUTION

SPARK PLUGS

You should inspect spark plugs periodicallyfor carbon deposits. When carbonaccumulates on a spark plug, a strongspark may not be produced. Removecarbon deposits with a wire or pin andadjust the spark plug gap.

76G-09-018 76G-09-019

ALTO K10


9-19

ALTO

103

76G-74E

76G-09-020

ALTO K10

EXAMPLE To access the spark plugs,

For Alto1. Disconnect the coupler while pushing the

release lever,2. Remove the bolts, and3. Pull the spark plug boots.

For Alto K101. Unclamp and remove the air cleaner case.2. If necessary, disconnect the coupler (1)

while pushing the release lever.3. Remove the ignitor bolts.4. Pull the spark plug boots out.

CAUTION

76G-09-021

Spark Plug gap "a"Alto - 0.85 ± 0.5 mmAlto K10 - 1.0 ± 0.05 mm


9-20

ALTO

EXAMPLE• When disconnecting the spark plug

cables, pull on the boot, not on thecable itself. Pulling on the cable candamage it.

• When installing the spark plugs,screw them in with your fingers toavoid stripping the threads. Tightenwith a torque wrench to :Alto - 13.0–22.0 N-m (1.3–2.2 kg-m,9.4–15.9 lb-ft)Alto K10 - 25 N-m (2.5 kg-m, 18.0lb-ft).Do not allow contaminants to enterthe engine through the spark plugholes when the plugs are removed.

• Never use spark plugs with thewrong thread size or length.

CAUTIONWhen replacing spark plugs, youshould use the brand and typespecified for your vehicle. For thespecified plugs, refer to the“SPECIFICATIONS” section at the endof this book.

NOTE:When installation, make sure the wires,couplers, sealing rubber of top cover andwashers, are correctly returned in place.

104


9-21

NOTE:If you experience some firing problem ofspark plugs, such as, hard engine-starting,misfire etc., the cause may be located notonly on spark plugs but also on deterioratedignition wiring (generally, used for more than80,000 km or five years). If spark plugreplacement does not solve the problem,have the ignition wiring and other ignitionsystem inspected by your MARUTI SUZUKIdealer.

76G-09-022

BRAKES

Brake FluidCheck the brake fluid level by looking at thereservoir in the engine compartment. Checkthat the fluid level is between the “MAX”and “MIN” lines. If the brake fluid level isnear the “MIN” line, fill it up to the “MAX”line with MARUTI GENUINE brake fluid.

Failure to follow the guidelines belowcan result in personal injury orserious damage to the brake system.• If the brake fluid in the reservoir

drops below a certain level, thebrake warning light on theinstrument panel will come on (the

wwwww WARNING

VV VVV

76G-09-023

EXAMPLE EXAMPLE

FUEL FILTER REPLACEMEMT

Trust this replacement job to your MARUTISUZUKI authorised workshop.

105

76G-74E

parking brake must be fullydisengaged with ignition switch in"ON" position). Should the lightcome on, immediately ask yourMARUTI SUZUKI dealer to inspectthe brake system.

• A rapid fluid loss indicates a leak inthe brake system which should beinspected by your MARUTI SUZUKIdealer immediately.

• Brake fluid can harm your eyes anddamage painted surfaces. Usecaution when refilling the reservoir.

wwwww WARNING

VVVV V

76G-09-024


9-22

• Do not use any fluid other thanMARUTI GENUINE brake fluid. Donot use reclaimed fluid or fluid thathas been stored in old or opencontainers. It is essential thatforeign particles and other liquidsare kept out of the brake fluidreservoir.

The brake fluid should be replacedevery two years or 20,000 km.

NOTE:With disc brakes, the fluid level can beexpected to gradually fall as the brake padswear.

wwwww WARNING

CAUTION

76G-09-025

Brake PedalCheck if the brake pedal stops at theregular height without "spongy" feeling whenyou depress it. If not, have the brakesystem inspected by your MARUTI SUZUKIdealer. If you doubt the brake pedal for theregular height, check it as follows:

With the engine running, measure thedistance between the brake pedal and floorsilencer mat when the pedal is depressedwith approximately 30 kg (66 lbs) of force.The minimum distance required is 110 mm(4.3 in). Since your vehicle’s brake systemis self-adjusting, there is no need for pedaladjustment. If the pedal to floor wall distanceas measured above is less than the minimumdistance required, have your vehicle inspectedby your MARUTI SUZUKI dealer.

76G-09-026

106


9-23

NOTE:When measuring the distance between thebrake pedal and floor wall, be sure not toinclude any floor covering other thansilencer mat in the measurement.

If you experience any of the followingproblems with your vehicle’s brakesystem, have the vehicle inspectedimmediately by your MARUTI SUZUKIdealer.• Poor braking performance• Uneven braking (Brakes not working

uniformly on all wheels.)• Excessive pedal travel• Brake dragging• Excessive noise• Pedal pulsation (Pedal pulsates

when depressed.)

wwwww WARNING

Ratchet tooth specification "b"4th- 9thLever pull force (1)

200 N (20kg. 44 lbs)

Check the parking brake for properadjustment by counting the number of clicksmade by the ratchet teeth as you slowly pullup on the parking brake lever to the pointof full engagement. The parking brake levershould stop between the specified ratchetteeth and the rear wheels should besecurely locked. If the parking brake is notproperly adjusted or the brakes drag afterthe lever has been fully released, have theparking brake inspected and/or adjusted byyour MARUTI SUZUKI dealer.

76G-09-027

STEERING

Check the play of the steering wheel bygently turning it from left to right andmeasuring the distance that it moves beforeyou feel slight resistance. The play shouldbe between 0 – 30 mm (0.0 – 1.2 in).

Check that the steering wheel turns easilyand smoothly without rattling by turning itall the way to the right and to the left whiledriving very slowly in an open area. If theamount of free play is outside thespecification or you find anything else to bewrong, an inspection must be performed byyour MARUTI SUZUKI dealer.

76G-09-028

EXAMPLE

PARKING BRAKE

107

76G-74E

9-24


CLUTCH PEDAL

Measure the clutch pedal play by movingthe clutch pedal with your hand andmeasuring the distance it moves until youfeel slight resistance. The play in the clutchpedal should be between 15 – 20 mm (0.6– 0.8 in) If the play is more or less thanthe above, or clutch dragging is felt with thepedal fully depressed, have the clutchinspected by your MARUTI SUZUKI dealer.

76G-09-029

TYRES

The front and rear tyre pressurespecifications for your vehicle are listed onthe Tyre Inflation Pressure Label and in the“SPECIFICATIONS” section at the end ofthis book. Both the front and rear tyresshould have the specified tyre pressure.

Tyre InspectionInspect your vehicle’s tyres periodically byperforming the following checks:

1) Measure the air pressure with a tyregauge. Adjust the pressure if necessary.Remember to check the spare tyre too.

76G-09-030

• Air pressures should be checkedwhen the tyres are cold or you mayget inaccurate readings.

• Check the inflation pressure fromtime to time while inflating the tyregradually, until the specifiedpressure is obtained.

• Never underinflate or overinflate thetyres.Underinflation can cause unusualhandling characteristics or cancause the rim to slip on the tyrebead, resulting in an accident ordamage to the tyre or rim.Overinflation can cause the tyre toburst, resulting in personal injury.Overinflation can also causeunusual handling characteristicswhich may result in an accident.

wwwww WARNING

108


9-25

2) Check that the depth of the tread grooveis more than 1.6 mm (0.06 in). To helpyou check this, the tyres have moulded-in tread wear indicators in the grooves.When the indicators appear on the treadsurface, the remaining depth of the treadis 1.6 mm (0.06 in) or less and the tyreshould be replaced.

3) Check for abnormal wear, cracks anddamage. Any tyres with cracks or otherdamage should be replaced. If any tyresshow abnormal wear, have theminspected by your MARUTI SUZUKIdealer.

76G-09-031

Hitting curbs and running over rockscan damage tyres and affect wheelalignment. Be sure to have tyres andwheel alignment checked periodicallyby your MARUTI SUZUKI dealer.

4) Check for loose wheel nuts.5) Check that there are no nails, stones,

or other objects sticking into the tyres.

Your MARUTI SUZUKI is equippedwith tyres which are all the same typeand size. This is important to ensureproper steering and handling of thevehicle. Never mix tyres of differentsize or type on the four wheels ofyour vehicle. The size and type oftyres used should be only thoseapproved by MARUTI SUZUKI asstandard or optional equipment foryour vehicle.

wwwww WARNING

wwwww WARNING

Replacing the wheels and tyresequipped on your vehicle with certaincombinations of aftermarket wheelsand tyres can significantly change thesteering and handling characteristicsof your vehicle. Therefore, use onlythose wheel and tyre combinationsapproved by MARUTI SUZUKI asstandard or optional equipment foryour vehicle.

Replacing the original tyres with tyresof a different size may result in falsespeedometer or odometer readings.

wwwww WARNING

CAUTION

109


9-26

Tyre RotationTo avoid uneven wear of your tyres and toprolong their life, rotate the tyres asillustrated. Tyres should be rotated asrecommended in the periodic maintenanceschedule. After rotation, adjust front and reartyre pressures to the specification listed onyour vehicle’s Tyre Inflation Pressure Label.

Wheel BalancingIf the vehicle vibrates abnormally on smoothroad, have the wheels balanced at MarutiSuzuki authorized workshop.

Wheel AlignmentIn case of abnormal tyre wear or pullingtowards one side, have the wheel alignedat Maruti Suzuki authorized workshop.

76G-09-032

Changing WheelsTo change a wheel, use the followingprocedure:

1) Remove the jack , tools and spare wheelfrom the vehicle

NOTE:If it is hard to loosen the bolt that securesthe spare tyre, use the jack crank asillustrated.

2) Loosen, but do not remove the wheelnuts.

3) Jack up the vehicle (follow the jackinginstructions in the EMERGENCYSERVICE section in this manual)

76G-09-033

4) Remove the wheel nuts and wheel.

5) Before installing the new wheel, cleanany mud or dirt off from the surface ofthe wheel and hub with a clean cloth.Clean the hub carefully; it may be hotfrom driving.

6) Install the new wheel and replace thewheel nuts with their cone shaped endfacing the wheel. Tighten each nutsnugly by hand until the wheel issecurely seated on the hub.

7) Lower the jack and fully tighten the nuts[to 8.5 kg-m (61.5 lb-ft)] in a crisscrossfashion with a wrench as shown in theillustration.

76G-09-034

110


9-27

76G-09-035

76G-09-036

Use MARUTI Genuine wheel nuts andtighten them to the specified torqueas soon as possible after changingwheels. Incorrect wheel nuts orimproperly tightened wheel nuts maycome loose or fall off, which canresult in an accident. If you do nothave a torque wrench, have the wheelnut torque checked by a MARUTISUZUKI authorized dealer.

wwwww WARNING Tubeless Tyres (If equipped)The vehicle is equipped with TubelessTyres. In tubeless tyre, a thin layer of butylrubber is used for lining the inside of thetubeless tyre. This layer is to prevent airloss and fulfilling the purpose of tube. Theair pressure is maintained by the sealingbetween tyre bead and wheel rim. Tubelesstyres are having advantage of slow air lossand preventing sudden deflation whiledriving.

Care and maintenance tips for tubelesstyres1. Always maintain recommended inflation

pressure. Driving continously at lowinflation pressure can lead to tyre dam-age.

2. In case any leakage is found, check forany nail penetration/valve core damageor rim bent. Damaged wheel must notbe used.

3. In case tyre has run at low pressue, itmust be inspected for any defect.

4. Whenver new tyre is fitted, replace thevalve.

5. If continous high speed driving isrequired, increase tyres pressure by 5psi over recommended inflation pressure.

111


9-28

6. Never run the tyre beyond TWI (Treadwear indicator). The tyre is recommen-ded to be replaced when the remainingtread has worn to this point. The indica-tors are spaced across the tread aroundthe tyre marked by a triagular symbol(TWI).

7. Always prefer tubeless tyre mountingmachine. In case of manual mounting-tyre/wheel rim damage may occur.

8. In case of any problem, please get intouch with MARUTI SUZUKI authoriseddealer.

76G-09-037

76G-09-038

Batteries produce flammable hydrogengas. Keep flames and sparks awayfrom the battery or an explosion mayoccur. Never smoke when working inthe vicinity of the battery.

When checking or servicing thebattery, disconnect the negative cable.Be careful not to cause a short circuitby allowing metal objects to contactthe battery posts and the vehicle atthe same time.

wwwww WARNING

wwwww WARNING

EXAMPLE-1

EXAMPLE-2

BATTERY

112


9-29

To avoid harm to yourself or damageto your vehicle or battery, follow thejump starting instructions in theEMERGENCY SERVICE section of thismanual if it is necessary to jump startyour vehicle.

The level of the battery solution must bekept between the “MAX” and the “MIN” levellines at all times. If the level is found to bebelow the “MIN” level line, add distilledwater to the “MAX” level line. You shouldperiodically check the battery, batteryterminals, and battery hold-down bracket forcorrosion. Remove corrosion using a stiffbrush and ammonia mixed with water, orbaking soda mixed with water. Afterremoving corrosion, rinse with clean water.

If your vehicle is not going to be driven fora month or longer, disconnect the cable fromthe negative terminal of the battery to helpprevent discharge.

wwwww WARNING

FUSES

1. Main fuse2. Primary fuse (IG)3. Primary fuse (Not under ignition switch)4. Empty5. Empty6. Headlight (R)7. Headlight (L)8. Empty9. Radiator fan motor fuse0. Fuel injection system fusec. Air conditioner (If equipped)

76G-09-039

1. Main fuse2. Primary fuse (IG)3. Primary fuse (Not under ignition switch)4. Empty5. Empty6. Headlight (R)7. Headlight (L)8. Blower9. Radiator fan motor fuse0. Fuel injection system fusec. Air conditioner (If equipped)

76G-09-039

ALTO ALTO K10

113


9-30

This vehicle has three types of fuses, asdescribed below :

Main Fuse - The main fuse takes currentdirectly from the battery.

Primary Fuses - These fuses are betweenthe main fuse and individual fuses, and arefor electrical load groups.

Individual Fuses - These fuses are in thefuse box and for individual electrical circuits.

76G-09-040

EXAMPLE

1. HEATER 10A2. WIPER/WASHER 15A3. BLANK4. STOP 10A5. TAIL 10A6. RADIO/DOME 15A7. HORN HAZARD 15A8. BLOWER 25A9. IG 15A0. TURN/BACK 10Ac. STEERING 30Ad. CIGAR 15Ae. STARTER FUSE 30Af. FUSE PULLER

Main Fuse and Primary FusesThe main fuse and primary fuses arelocated in the engine compartment. If themain fuse blows, no electrical componentwill function. If a primary fuse blows, noelectrical component in the correspondingload group will function. When replacing themain fuse or a primary fuse, use a MARUTIgenuine replacement.

If the main fuse or a primary fuseblows, be sure to have your vehicleinspected by an authorized MARUTISUZUKI dealer. Always use a MARUTIgenuine replacement. Never use asubstitute such as a wire even for atemporary repair, or extensiveelectrical damage and a fire can result.

wwwww WARNING

MAIN FUSE / PRIMARY FUSES

80A All Electric Load

60A CIGAR, TURN/BACK, I.G./METER,

(IG) HEATER, REAR DEFG, WIPER/WASHER, POWER WINDOW

60A DOOR LOCK, TAIL, STOP, RADIO/DOME, HORN/HAZARD

76G-09-041

ALTO

114

76G-74E

9-31


1. HEATER 10A2. WIPER/WASHER 15A3. DOOR LOCK 20A4. STOP 10A5. TAIL 10A6. RADIO/DOME 15A7. HORN HAZARD 15A8. POWER STEERING 30A9. IG 15A0. TURN/BACK 10Ac. METER 10Ad. ACC 15Ae. CIGAR 15Af. STARTER FUSE 30Ag. FUSE PULLERh. POWER WINDOW 30A

76G-09-041A

ALTO K10

Fuse BoxThe fuse boxes are located in the enginecompartment and under the driver’s side ofthe dashboard.

To remove the fuse box cover under thedashboard pull off the cover.

NOTE:AltoTo remove the fuse from the fuse box usethe fuse puller given in the fuse box (underdashboard) as shown in the illustration.

76G-09-042

ALTO Fuse Box (under dashboard)

76G-09-042A

ALTO K10 Fuse Box (under dashboard)

NOTE:Alto K10Replace the fuse as described on the fusebox cover. Use the fuse puller given in thefuse box and keeping cover rib (1) indownward direction as shown.

115


9-32

Always be sure to replace a blownfuse with a fuse of the correctamperage. Never use a substitutesuch as aluminium foil or wire toreplace a blown fuse. If you replacea fuse and the new one blows in ashort period of time, you may have amajor electrical problem. Have yourvehicle inspected immediately by yourMARUTI SUZUKI dealer.

NOTE:Make sure that the fuse box always carriesspare fuses.

wwwww WARNING

76G-09-043

BULB REPLACEMENT

• Light bulbs can be hot enough toburn your finger right after beingturned off. This is true especially forhalogen headlight bulbs. Replace thebulbs after they become coolenough.

• The headlight bulbs are filled withpressurized halogen gas. They canburst and injure you if they are hitor dropped. Handle them carefully.

The oils from your skin may cause ahalogen bulb to overheat and burstwhen the lights are on. Grasp a newbulb with a clean cloth.

Frequent replacement of a bulbindicates the need for an inspection ofthe electrical system. This should becarried out by your MARUTI SUZUKIdealer.

CAUTION

CAUTION

wwwww WARNING

76G-09-044

76G-09-045

116


9-33

Front Interior LightPress the front part of the lens toward youand pull down the lens. To install it, simplypush it back in.

The bulb can be removed by simply pullingit out. When replacing the bulb, make surethat the contact springs are holding the bulbsecurely.

76G-09-046

Front Clearance/Turn Signal Light, SideTurn Signal Light, rear CombinationLight, Registration Plate Light.To remove a bulb holder from a lighthousing, turn the holder counterclockwiseand pull it out. To install the holder, pushthe holder in and turn it clockwise.

Two types (small oval and round) of bulbare used for these lights. To remove andinstall a small oval bulb, simply pull out orpush in the bulb.

76G-09-048

HeadlightsOpen the bonnet. Disconnect the coupler.Remove the sealing rubber.Push the retaining spring forward andunhook it. Then remove the bulb. Install anew bulb in the reverse order of removal.Note:Your vehicle is provided with two sparehead l igh t bu lbs fo r rep lacement inemegency.

76G-09-047

117


9-34

To remove a round bulb from a bulb holder,push in the bulb and turn itcounterclockwise. To install a new bulb,push it in and turn it clockwise. You canaccess the individual bulb holders asdescribed below:

76G-09-049

Side turn signal lightRemove the lens by using a plain screwdriver covered with a soft cloth.

76G-09-051

Front clearance light / Turn LightTrust this replacement job to your MARUTISUZUKI authorised workshop.

76G-09-050

118


9-35

Rear combination light (tail, stop, turnsignal, etc.)Undo the screws that secure the housingand remove the housing by sliding in thedirection of the white arrow in theillustration.

76G-09-052

WIPER BLADES

If the wiper blades become brittle ordamaged, or make streaks when wiping,replace the wiper blades.

To install new wiper blades, follow theprocedure below.

To avoid scratching or breaking thewindow, do not let the wiper armstrike the windshield while replacingthe wiper blade.

CAUTION

76G-09-054

Registration plate lightTurn the lens counterclockwise and pull itoff

76G-09-053

119


9-36

wwwww WARNING

NOTE:Some wiper blades may be different from theones described here depending on vehiclespecifications. If so consult your MARUTISUZUKI dealer for proper replacement method.

The left and the right wiper armassemblies are different from eachother. In case you have to remove thewiper arm assemblies for any reason,remember not to interchange the twowhile fitting them back. Wrong fitmentmay lead to windshield breakage. 2. Squeeze lock lever (A) towards wiper

arms (B) and remove the wiper framefrom the arm as shown.

76G-09-056

For windshield wipers:1. Hold the wiper arm away from the

window.

76G-09-055

120

76G-74E

MEMO

121

76G-74E EMERGENCY SERVICE

10

EMERGENCY SERVICE

Jacking Instructions ........................................................................................10-1

Jump Starting Instructions ............................................................................ 10-2

Towing ................................................................................................................10-4

Towing Hook (if equipped) ............................................................................10-4

Emergency Remedies ......................................................................................10-4

Warning Triangle ..............................................................................................10-5

122

76G-74E

JACKING INSTRUCTIONS

1) Park the vehicle securely on hard levelground.

2) Apply the parking brake firmly andchange into "R" (Reverse) gear. Chokethe front and rear wheel diagonallyopposite the wheel to be changed.

3) Switch on the hazard warning flasher ifyour vehicle is in or near traffic.

4) Slacken but do not remove wheel nutson the wheel to be changed.

5) Position the jack vertically and raise thejack by turning the jack handle clockwiseuntil the jack head recess fits the frameboss.

EMERGENCY SERVICE

10-1

NOTE:Use the wheel nut wrench in combinationwith jack crank to raise or lower the jackas shown in the illustration.

76G-10-001 76G-10-002 76G-10-004

76G-10-003 76G-10-005

6) Continue to raise the jack slowly andsmoothly until the tyre clears the ground.Do not raise the vehicle more thannecessary.

123

76G-74E

never allow passengers to remain inthe vehicle.

JUMP STARTING INSTRUCTIONS

• Never attempt to jump start yourvehicle if the battery appears to befrozen. Batteries in this conditionmay explode or rupture if jumpstarting is attempted.

• When making jump leadconnections, be certain that yourhands and the jump leads remainclear from pulleys, belts, or fans.

• Batteries produce flammablehydrogen gas. Keep flames andsparks away from the battery or anexplosion may occur. Never smokewhen working in the vicinity of thebattery.

• If the booster battery you use forjump starting is installed in anothervehicle, make sure the two vehiclesare not touching each other.

• If your battery dischargesrepeatedly, for no apparent reason,have your vehicle inspected by anauthorized MARUTI SUZUKI dealer.

• To avoid harm to yourself ordamage to your vehicle or battery,follow the jump starting instructionsbelow precisely and in order. If youare in doubt, call MARUTI SUZUKIauthorized workshop.

wwwww WARNING

wwwww WARNING

EMERGENCY SERVICE

10-2

VVVV V

• Use the jack only to change wheels.• Never jack up the vehicle on an

inclined surface.• Never raise the vehicle with the jack in

a location other than under the frameboss near the wheel to be changed.

• Make sure that the jack is raised at least2 inches (51 mm) before it contacts thevehicle. Use of the jack when it is within2 inches of being fully collapsed mayresult in failure of the jack.

• Never get under the vehicle when itis supported by the jack.

• Never run the engine when thevehicle is supported by the jack and

wwwww WARNING

VV VVV

76G-10-006 76G-10-007

76G-10-008

124

76G-74E

• Vehicle equipped with electronic fuelinjection system will not start bypushing or towing as the fuel pumpwill not work in this condition. Thisstarting method could also result inpermanent damage to the catalyticconverter. Use jump leads to start avehicle with a weak or flat battery.

When jump starting your vehicle, use thefollowing procedure:1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12Vbattery close to your vehicle so that thejump leads will reach both batteries.When using a battery installed onanother vehicle, DO NOT LET THEVEHICLES TOUCH. Apply the parkingbrakes fully on both vehicles.

2) Turn off all vehicle accessories, exceptthose necessary for safety reasons (forexample, headlights or hazard lights).

3) Make jump lead connections as follows:

a) Connect one end of the first jumplead to the positive (+) terminal of theflat battery.

b) Connect the other end to the positive(+) terminal of the booster battery.

c) Connect one end of the second jumplead to the negative (-) terminal ofthe booster battery.

d) Make the final connection to anunpainted, heavy metal part of theengine of the vehicle with the flatbattery.

Never connect the jump lead directlyto the negative (-) terminal of thedischarged battery, or an explosionmay occur.

4) If the booster battery you are using isfitted to another vehicle, start the engineof the vehicle with the booster battery.Run the engine at moderate speed.

5) Start the engine of the vehicle with theflat battery.

6) Remove the jump leads in the exactreverse order in which you connectedthem.

EMERGENCY SERVICE

10-3

wwwww WARNING CAUTION

76G-10-009 76G-10-010

125

76G-74E

TOWING

If you need to have your vehicle towed,contact a professional service. Your dealercan provide you with detailed towinginstructions

To help avoid damage to your vehicleduring towing, proper equipment andtowing procedures must be used.

EMERGENCY REMEDIES

EMERGENCY SERVICE

10-4

CAUTION

Manual TransmissionWhenever possible, your vehicle should betowed from the front with the front wheelslifted. If the steering and drivetrain are ingood condition, your vehicle may be towedfrom the rear with the rear wheels lifted andthe front wheels on the ground. Beforetowing, make sure the steering is unlockedand the transmission is in neutral.

If the Starter Does Not Operate:1) Try turning the ignition switch to the

“START” position with the headlightsturned on to determine the batterycondition. If the headlights goexcessively dim or go off, it usuallymeans that either the battery is flat orthe battery terminal contact is poor.Recharge the battery or correct batteryterminal contact as necessary.

2) If the headlights remain bright, check thefuses. If the reason for failure of thestarter is not obvious, there may be amajor electrical problem. Have thevehicle inspected by your authorizedMARUTI SUZUKI dealer.

If the Engine is FloodedIf the engine is flooded with petrol, it maybe hard to start. If this happens, press theaccelerator pedal all the way to the floorand hold it there while cranking the engine.(Do not operate the starter motor for morethan 15 seconds). Release the acceleratoras soon as the engine has started.

If the Engine OverheatsThe engine could overheat temporarily undersevere driving conditions. If the enginecoolant temperature warning light comes on,it indicates overheating during driving:

TOWING HOOK (If equipped)

76G-10-011

126

76G-74E

engine until these problems have beencorrected.

3) If you do not find a leak, carefully addcoolant to the reservoir and then theradiator, if necessary. (Refer to “ENGINECOOLANT” in the “INSPECTION ANDMAINTENANCE” section.)

It is dangerous to remove the radiatorcap when the water temperature ishigh, because scalding fluid andsteam may be blown out underpressure. The cap should only betaken off when the coolanttemperature has lowered.

To help prevent personal injury, keephands, tools and clothing away fromthe engine cooling fan and air-conditioner fan (if equipped). Theseelectric fans can automatically turn onwithout warning.

EMERGENCY SERVICE

10-5

wwwww WARNING

wwwww WARNING

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place andpark.

3) Let the engine run at normal idle speedfor a few minutes until engine coolanttemperature warning light goes off.

If you see or hear escaping steam,stop the vehicle in a safe place andimmediately turn off the engine to letit cool. Do not open the bonnet whensteam is present. When the steam canno longer be seen or heard, open thehood to see if the coolant is stillboiling. If it is, you must wait until itstops boiling before you proceed.

If the engine coolant temperature warninglight does not goes off:1) Turn off the engine and check that the

water pump belt and pulleys are notdamaged or slipping. If any abnormalityis found, correct it.

2) Check the coolant level in the reservoir.If it is found to be lower than the “LOW”line, look for leaks at the radiator, waterpump, and radiator and heater hoses. Ifyou locate any leaks that may havecaused the overheating, do not run the

wwwww WARNING

WARNING TRIANGLE

In case of vehicle break-down or duringemergency stopping, where, your vehiclecould become a potential traffic hazard,keep the warning triangle, provided withyour vehicle, on the road free from anyobstacles behind your vehicle so as to warnthe approaching traffic, at an approximatedistance of 50-100 m. The reflecting sideof the triangle should face the on comingtraffic. Please activate the hazard warninglamps before alighting the vehicle to keepthe warning triangle.

1

76G-10-012

EXAMPLE

127

76G-74E

• Remove the warning triangle carefullyfrom the cover as shown by arrow 1.

• Open both the reflector arms as shownby arrow and lock the arms with eachother with the clip provided in the rightarm. Open the bottom stand in counterclock-wise direction as shown by arrow 3.Position the warning triangle behind thevehicle on a plain surface.

• Reverse the removal procedure forkeeping inside the cover.

EMERGENCY SERVICE

10-6

76G-10-013 76G-10-014

128

76G-74E

MEMO

129

76G-74E BODY WORK CARE

11

BODY WORK CARE

Corrosion Prevention ....................................................................................... 11-1

Vehicle Cleaning ............................................................................................... 11-2

130

76G-74E

CORROSION PREVENTION

the vehicle which are not well ventilatedto permit quick drying.

This information illustrates the necessity ofkeeping your vehicle (particularly theunderbody) as clean and dry as possible.It is equally important to repair any damageto the paint or protective coatings as soonas possible.

How to Help Prevent Corrosion

Wash your vehicle frequentlyThe best way to preserve the finish on yourvehicle and to help avoid corrosion is tokeep it clean with frequent washing.Wash your vehicle regularly during thewinter and immediately after the winter.Keep your vehicle, particularly theunderside, as clean and dry as possible.If you frequently drive on salted roads, yourvehicle should be washed at least once amonth during the winter. If you live near theocean, your vehicle should be washed atleast once a month throughout the year.For washing instructions, refer to the“VEHICLE CLEANING” section.

Remove foreign material depositsForeign material such as salts, chemicals,road oil or tar, tree sap, bird droppings andindustrial fall-out may damage the finish ofyour vehicle if it is left on painted surfaces.Remove these types of deposits as quickly

as possible. If these deposits are difficult towash off, an additional cleaner may berequired. Be sure that any cleaner you useis not harmful to painted surfaces and isspecifically intended for your purposes.Follow the manufacturer’s directions whenusing these special cleaners.

Repair finish damageCarefully examine your vehicle for damageto the painted surfaces. Should you find anychips or scratches in the paint, touch themup immediately to prevent corrosion fromstarting. If the chips or scratches have gonethrough to the bare metal, have a qualifiedbody shop make the repair.

Keep Passenger and luggagecompartments clean.Moisture, dirt or mud can accumulate underthe floor mats and may cause corrosion.Occasionally, check under these mats toensure that this area is clean and dry. Morefrequent checks are necessary if the vehicleis used off road or in wet weather.

Certain cargos such as chemicals, fertilizers,cleaners, salts, etc., are extremely corrosiveby nature. These products should betransported in sealed containers. If a spillor leak does occur, clean and dry the areaimmediately.

It is important to take good care of yourvehicle to protect it from corrosion.Listed below are instructions for how tomaintain your vehicle to prevent corrosion.Please read and follow these instructionscarefully.

Important Information About Corrosion

Common causes of corrosion1) Accumulation of road salt, dirt, moisture,

or chemicals in hard to reach areas ofthe vehicle underbody or frame.

2) Chipping, scratches and any damage totreated or painted metal surfacesresulting from minor accidents orabrasion by stones and gravel.

Environmental conditions whichaccelerate corrosion1) Road salt, dust control chemicals, sea

air or industrial pollution will allaccelerate the corrosion of metal.

2) High humidity will increase the rate ofcorrosion particularly when thetemperature range is just above thefreezing point.

3) Moisture in certain areas of a vehicle foran extended period of time may promotecorrosion even though other bodysections may be completely dry.

4) High temperatures will cause anaccelerated rate of corrosion to parts of

BODY WORK CARE

11-1

131

76G-74E

Store your vehicle in a dry, well-ventilated area.Do not park your vehicle in a damp, poorlyventilated area. If you often wash yourvehicle in the garage or if you frequentlydrive it in when wet, your garage may bedamp. The high humidity in the garage maycause or accelerate corrosion. A wet vehiclemay corrode even in a heated garage if theventilation is poor.

Do not apply additional undercoatingor rust preventive coating on oraround exhaust system componentssuch as the exhaust pipes, etc. A firecould be started if the undercoatingsubstance becomes overheated.

Cover your vehicleIf you cannot regularly park your vehicle ina garage, we recommend you use a vehiclecover.

VEHICLE CLEANING

cleaner for tougher stains. If you use afabric cleaner, carefully follow themanufacturer’s instructions and precautions.

Seat BeltsClean seat belts with a mild soap andwater. Do not use bleach or dye on thebelts. They may weaken the fabric in thebelts.

Vinyl floor matsOrdinary dirt can be removed from vinyl withwater or mild soap. Use a brush to helploosen dirt. After the dirt is loosened, rinsethe mat thoroughly with water and dry it inthe shade.

CarpetsRemove dirt and soil as much as possiblewith a vacuum cleaner. Using a mild soapsolution, rub stained areas with a cleandamp cloth. To remove soap, rub the areasagain with a cloth dampened with water.Repeat this until the stain is removed, oruse a commercial carpet cleaner for tougherstains. If you use a carpet cleaner, carefullyfollow the manufacturer’s instructions andprecautions.

wwwww WARNING

When cleaning the interior or exteriorof the vehicle, NEVER USE flammablesolvents such as lacquer thinners,petrol, benzene or cleaning materialssuch as bleach or strong householddetergents. The materials could causepersonal injury or damage to thevehicle.

Cleaning the Interior

Vinyl upholsteryPrepare a solution of soap or mild detergentmixed with warm water. Apply the solutionto the vinyl with a sponge or soft cloth andlet it soak for a few minutes to loosen dirt.Rub the surface with a clean, damp clothto remove dirt and the soap solution. Ifsome dirt still remains on the surface,repeat this procedure.

Fabric upholsteryRemove loose dirt with a vacuum cleaner.Using a mild soap solution, rub stainedareas with a clean damp cloth. To removesoap, rub the areas again with a clothdampened with water. Repeat this until thestain is removed, or use a commercial fabric

wwwww WARNING

BODY WORK CARE

11-2

132

76G-74E

Cleaning the Exterior

It is important that your vehicle bekept clean and free from dirt. Failureto keep your vehicle clean may resultin fading of the paint or corrosion tovarious parts of the vehicle body.

Washing

• Never attempt to wash and wax yourvehicle with the engine running.

• When cleaning the underside of thebody and fender, where there maybe sharp-edged parts, you shouldwear gloves and a longsleeved shirtto protect your hands and armsfrom being cut.

• After washing your vehicle, carefullytest the brakes before driving tomake sure they have maintainedtheir normal effectiveness.

When washing the vehicle, follow theinstructions below:

1) Flush the underside of body and wheelhousings with pressurized water toremove mud and debris. Use plenty ofwater.

When washing the vehicle, avoiddirecting steam or hot water of morethan 800C (1760F) on plastic parts.

2) Remove dirt and mud from the bodyexterior with running water. You may usea soft sponge or brush. Do not use hardmaterials which can scratch the paint.

3) Wash the entire exterior with a milddetergent or car wash soap using asponge or soft cloth. The sponge orcloth should be frequently soaked in thesoap solution.

When using a commercial car washproduct, observe the cautionsspecified by the manufacturer. Neveruse strong household detergents orsoaps.

BODY WORK CARE

11-3

wwwww WARNING

CAUTION

4) Once the dirt has been completelyremoved, rinse off the detergent withrunning water.

5) After rinsing, wipe off the vehicle bodywith a wet chamois or cloth and allowit to dry in the shade.

6) Check carefully for damage to paintedsurfaces. If there is any damage,“Touchup” the damage following theprocedure below:

a) Clean all damaged spots and allowthem to dry.

b) Stir the paint and “touchup” thedamaged spots lightly using a smallbrush.

c) Allow the paint to dry completely.

WaxingAfter washing the vehicle, waxing andpolishing are recommended to furtherprotect and beautify the paint.• Only use waxes and polishes of good

quality.• When using waxes and polishes,

observe the precautions specified by themanufacturers.

CAUTION

CAUTION

133

76G-74E GENERAL INFORMATION

12

GENERAL INFORMATION

Vehicle Identification ....................................................................................... 12-1

134

76G-74EGENERAL INFORMATION

12-1

76G-12-001 76G-12-002

Chassis Serial NumberThe chassis and/or engine serial numbersare used to register the vehicle. They arealso used to assist your dealer whenordering or referring to special serviceinformation. Whenever you have occasion toconsult your MARUTI SUZUKI dealer,remember to identify your vehicle with thisnumber. Should you find the number difficultto read, you will also find it on theidentification plate in the enginecompartment.

VEHICLE IDENTIFICATION

Engine Serial NumberThe engine serial number is stamped on thecylinder block as shown in the illustrationand also on the identification plate.

135

76G-74E SPECIFICATIONS

13

SPECIFICATIONSNOTE:Specifications are subject to change without notice.

ITEM: DIMENSIONS UNIT:mmALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Overall length 3495 3620

Overall width 1475 1495/1475 (without side moulding)

Overall height 1460 1460

Wheelbase 2360 2360

Tread front 1295 1295

rear 1290 1290

Ground clearance 160 160

ITEM: MASS (WEIGHT) UNIT:KgALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Kerb mass (weight) 690-705 750-765

Gross vehicle mass (weight) rating 1140 1185

Seating Capacity 5 persons 5 persons

ITEM: ENGINEALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Type F8D K10B

Number of cylinders 3 3

Bore 68.5 73

Stroke 72.0 79.5

Piston displacement 796 cc 998 cc

Compression ratio 9.2 ± 0.2 : 1 10.0 ± 0.4 : 113-1

136

76G-74E

ITEM: ELECTRICALALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Standard spark plug NGK-DCPR7E, BOSCH-YR7DC NGK KR6A-10Battery 34B20L (27AH/5HR) 38B20L (28AH/5HR)Fuses See “INSPECTION AND MAINTENANCE” sectionHeadlight 12V 55/60WTurn signal light 12V 21WSide turn signal light 12V 5WClearance light 12V 5WTail/brake light 12V 21/5WRegistration plate light 12V 5WReversing light 12V 21WHigh Mount Stop Lamp 12V W16W

ITEM: WHEEL AND SUSPENSIONALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Tyre size, front and rear 145/80R12 155/65R13Tyre pressures front/rear 2.1 kg/cm2 2.2 kg/cm2

Suspension type front Mac Pherson Strutrear 3-link-rigid axle suspension

ITEM: STEERING

Toe-in front 0 ± 1 mm

ITEM: CAPACITIESALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi)

Coolant (Including reservoir tank) 3.5 Ltrs 4.3 LtrsFuel tank 35.0 Ltrs 35.0 LtrsEngine oil (with oil filter) 2.7 Ltrs 2.9 LtrsTransmission oil 2.2 Ltrs 2.2 Ltrs

SPECIFICATIONS

13-2

137

76G-74E

MEMO

138

76G-74E

MEMO

139

76G-74E

MEMO

140

76G-74E

MEMO

Download Owners Manual Indian Cars Pdf Format Maruti ......Maruti Suzuki offers the Emission...

Documents

Transcript of Download Owners Manual Indian Cars Pdf Format Maruti ......Maruti Suzuki offers the Emission...