Documentation TopSolid’Cam - Amazon S3...TopSolid ® is a product name of Missler Software. The...

Documentation

TopSolid’Cam

Tools functions in 7.8

© 2013, Missler Software. 7, Rue du Bois Sauvage F-91055 Evry, FRANCE Web: http://www.topsolid.com E-mail: [email protected] All rights reserved. This information is subject to change without warning. No material may be reproduced or transmitted, regardless of the manner, electronic or mechanical means used or purpose, without formal written consent from Missler Software. TopSolid ® is a registered trademark of Missler Software. TopSolid ® is a product name of Missler Software. The information and the software contained within this document are subject to change without prior warning and should not be construed as a commitment by Missler Software. The software covered by this document is supplied under license, and may only be used and duplicated in compliance with the terms of this license. Rev.01

Contents - SpottingDrill (Spotting Drill) ............................................................................................................................................ 7

- CenterDrill (Center Drill) ................................................................................................................................................. 8

- TwistDrill (Twist Drill) .................................................................................................................................................... 10

- FlatDrill (Flat Drill) ......................................................................................................................................................... 11

- GunDrill (Gun Drill) ........................................................................................................................................................ 12

- FaceMill (Face Mill) ....................................................................................................................................................... 13

- SideMill (Side Mill) ........................................................................................................................................................ 14

- SlotMill (Slot Mill) ......................................................................................................................................................... 15

- TSlotMill (T Slot Mill) ..................................................................................................................................................... 16

- RadiusedMill (Radiused Mill) ........................................................................................................................................ 17

- BallNoseMill (Ball Nose Mill) ......................................................................................................................................... 18

- LollipopMill (Lollipop Mill) ............................................................................................................................................ 19

- ConicNoseMill (Conic Nose Mill) ................................................................................................................................... 20

- ConicNoseBallMill (Conic Nose Ball Mill) ...................................................................................................................... 21

- SpotFaceMill (Spot Face Mill) ....................................................................................................................................... 22

- BackSpotFaceMill (Back Spot Face Mill) ....................................................................................................................... 23

- CounterboringMill (Counterboring Mill) ....................................................................................................................... 24

- CornerRoundingMill (Corner Rounding Mill) ................................................................................................................ 25

- ChamferMill (Chamfer Mill) .......................................................................................................................................... 26

- ReverseChamferMill (Reverse Chamfer Mill) ............................................................................................................... 27

- DoubleChamferMill (Double Chamfer Mill) .................................................................................................................. 28

- DiscMill (Disc Mill) ......................................................................................................................................................... 29

- RadiusedStaggeredTeethMill (Radiused Staggered Teeth Mill) ................................................................................... 30

- SpecialMill (Special Mill) ............................................................................................................................................... 31

- ConstantReamer (Constant Reamer) ............................................................................................................................ 32

- BoringBar (Boring Bar) .................................................................................................................................................. 33

- Tap (Tap) ....................................................................................................................................................................... 34

- ExternalThreadMill (External Thread Mill).................................................................................................................... 35

- InternalThreadMill (Internal Thread Mill) ..................................................................................................................... 36

- ExternalTurn (External Turn) ........................................................................................................................................ 37

- InternalTurn (Internal Turn) .......................................................................................................................................... 39

- ExternalGroove (ExternalGroove) ................................................................................................................................. 41

- InternalGroove (Internal Groove) ................................................................................................................................. 42

- FrontalGroove (Frontal Groove) ................................................................................................................................... 44

- ExternalThread (External Thread) ................................................................................................................................. 45

- InternalThread (Internal Thread) .................................................................................................................................. 46

- BallTouch (Ball Touch) .................................................................................................................................................. 47

- ClampGroove (Clamp Groove) ...................................................................................................................................... 48

- ClampThread (Clamp Thread) ....................................................................................................................................... 49

- ClampInsert (Clamp Insert) ........................................................................................................................................... 50

- ToolingHolder (Tooling Holder) .................................................................................................................................... 51

- ToolingShank (Tooling Shank) ....................................................................................................................................... 52

- ClampingInsert (Clamping Insert) ................................................................................................................................. 55

- CylindricalToolingShank (Cylindrical Tooling Shank) .................................................................................................... 56

- CylindricalToolingHolder (Cylindrical Tooling Holder) .................................................................................................. 57

- SquareToolingShank (Square Tooling Shank) ............................................................................................................... 58

- SquareToolingHolder (Square Tooling Holder) ............................................................................................................. 59

- ToolOffset (Tool Offset) ................................................................................................................................................ 60

- CollisionAnalysisRevolutionShape (Collision Analysis Revolution Shape) .................................................................... 61

- CollisionAnalysisShape (Collision Analysis Shape) ........................................................................................................ 62

- Tag (Tag) ........................................................................................................................................................................ 63

- CuttingShape (Cutting Shape) ....................................................................................................................................... 64

- CuttingRevolutionShape (Cutting Revolution Shape) ................................................................................................... 65

ClampingSystemFrame ................................................................................................................................................... 66

ClampingSystemName .................................................................................................................................................... 67

ClampingSystemSize ....................................................................................................................................................... 68

ClampingSystemType ...................................................................................................................................................... 69

ClearanceAngle ............................................................................................................................................................... 70

CoolantNozzle ................................................................................................................................................................. 71

CornerRadius ................................................................................................................................................................... 72

CornerRadius1 ................................................................................................................................................................. 73

CornerRadius2 ................................................................................................................................................................. 74

CuttingAngle.................................................................................................................................................................... 75

CuttingBottomDiameter ................................................................................................................................................. 76

CuttingDiameter .............................................................................................................................................................. 77

CuttingEdgeDepth ........................................................................................................................................................... 78

CuttingEdgeOrigin ........................................................................................................................................................... 79

CuttingEdgeShape ........................................................................................................................................................... 80

CuttingEdgeSize............................................................................................................................................................... 81

CuttingEdgeWidth ........................................................................................................................................................... 82

CuttingLength .................................................................................................................................................................. 83

CuttingTopDiameter ....................................................................................................................................................... 84

CuttingWidth ................................................................................................................................................................... 85

DepthDrilling ................................................................................................................................................................... 86

DepthReaming ................................................................................................................................................................ 87

- DepthTapping ............................................................................................................................................................... 88

- DepthThreading ............................................................................................................................................................ 89

- EntryDiameter ............................................................................................................................................................... 90

FluteLength ..................................................................................................................................................................... 91

GrooveExternalDiameter ................................................................................................................................................ 92

GrooveInternalDiameter ................................................................................................................................................. 93

HandOfTool ..................................................................................................................................................................... 94

- InitialDistance ............................................................................................................................................................... 95

- InsertThickness ............................................................................................................................................................. 96

LeftHand .......................................................................................................................................................................... 97

- MaximalDistance .......................................................................................................................................................... 98

MaximumRampAngle...................................................................................................................................................... 99

- MinimalDistance ......................................................................................................................................................... 100

- NominalDiameter........................................................................................................................................................ 101

- Norm ........................................................................................................................................................................... 102

- NumberOfThreadTeeth .............................................................................................................................................. 103

- NumberOfToolTeeth ................................................................................................................................................... 104

- Offset2d ...................................................................................................................................................................... 105

- Offset3d ...................................................................................................................................................................... 106

- OffsetDescription ........................................................................................................................................................ 107

- OverLength ................................................................................................................................................................. 108

- Pitch ............................................................................................................................................................................ 109

- PlaneCompensation .................................................................................................................................................... 110

- PlungeDirection .......................................................................................................................................................... 111

- PointCompensation .................................................................................................................................................... 114

- RespectDirection ......................................................................................................................................................... 115

Revolute Section ........................................................................................................................................................... 118

Revolution Section ........................................................................................................................................................ 119

RevolutionProfile .......................................................................................................................................................... 120

ShankDiameter .............................................................................................................................................................. 121

ShankHeight .................................................................................................................................................................. 122

ShankMaximalDiameter ................................................................................................................................................ 123

ShankMinimalDiameter ................................................................................................................................................ 124

ShankWidth ................................................................................................................................................................... 125

Shape ............................................................................................................................................................................. 126

Tag ................................................................................................................................................................................. 127

ThreadProfile ................................................................................................................................................................ 128

TipAngle ........................................................................................................................................................................ 129

ToolingSystemFrame..................................................................................................................................................... 130

ToolingSystemFrameLeft .............................................................................................................................................. 131

ToolingSystemFrameRight ............................................................................................................................................ 132

ToolingSystemName ..................................................................................................................................................... 133

ToolingSystemSize......................................................................................................................................................... 134

ToolingSystemType ....................................................................................................................................................... 135

Cutting Tool Material Category ..................................................................................................................................... 136

Tool example 1 : Multi-Diameter Drill solution 1 ......................................................................................................... 137

Tool example 1 : Multi-Diameter Drill solution 2 ......................................................................................................... 140

Tool example 2 : Multi-Diameter Drill .......................................................................................................................... 143

- SpottingDrill (Spotting Drill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) FluteLength (Flute Length) = [L] TipAngle (Tip Angle) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.8.102.000

For this tool, you need to define 2 Tool Offset Tool offset (1) :

Offset 3D = 0 Offset 2D = 0 Tool offset (2) :

Offset 3D = 0 Offset 2D = [B] / 2

- CenterDrill (Center Drill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) FluteLength (Flute Length) = [U] TipAngle (Tip Angle) = [A] DepthDrilling (Depth Drilling) = [I2] CuttingBottomDiameter (Cutting Bottom Diameter) = [d2]

CuttingTopDiameter (Cutting Top Diameter) = [D]

Version 7.8.102.000



Offset 3D = 0 Offset 2D = [d2] / 2 Tool offset (3) :

Offset 3D = 0 Offset 2D = [d2] / 2 Tool offset (4) :

Offset 3D = 0 Offset 2D = [D] / 2

- TwistDrill (Twist Drill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) FluteLength (Flute Length) = [E] OverLength (Over Length) = [F] TipAngle (Tip Angle) = [D] DepthDrilling (Depth Drilling) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084




- FlatDrill (Flat Drill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) FluteLength (Flute Length) = [E] OverLength (Over Length) = [F] DepthDrilling (Depth Drilling) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084

For this tool, you need to define 1 Tool Offset

Offset 3D = 0 Offset 2D = CuttingDiameter / 2 = [B] / 2

- GunDrill (Gun Drill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) FluteLength (Flute Length) ) = [E] OverLength (Over Length) ) = [F] TipAngle (Tip Angle) = [D] DepthDrilling (Depth Drilling) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.8.102.000




- FaceMill (Face Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CornerRadius (Corner Radius) = [D] CuttingAngle (Cutting Angle) = [E] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.6.301.084 Rules :

- If the tool use a round insert (R) , we have : CuttingAngle (Cutting Angle) = [E] = 0 and CornerRadius (Corner Radius) = [D] = value of the radius

- If the insert is not a round insert , the variable CornerRadius (Corner Radius) = [D] = 0 In this case we don’t use the corner radius for calculation, so set is at 0.


If [D] = 0 , then Offset 3D = 0 If [D] <> 0 , then Offset 3D = [D] Offset 2D = [B] / 2

- SideMill (Side Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084



- SlotMill (Slot Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.6.301.084 For this tool, you need to define 1 Tool Offset


- TSlotMill (T Slot Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingWidth (Cutting Width) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084

For this tool, you need to define 2 Tool Offset : Tool offset (1) :

Offset 3D = 0 Offset 2D = [B] / 2 Tool offset (2) :


- RadiusedMill (Radiused Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CornerRadius (Corner Radius) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.6.301.084


Offset 3D = [D] Offset 2D = [B] / 2 Tool offset (2) :

Offset 3D = [D] Offset 2D = [B] / 2

- BallNoseMill (Ball Nose Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.6.301.084


Offset 3D = [B] / 2 Offset 2D = [B] / 2 Tool offset (2) :

Offset 3D = [B] / 2 Offset 2D = [B] / 2

- LollipopMill (Lollipop Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [L] CuttingDiameter (Cutting Diameter) = [D]

Version 7.8.102.000


Offset 3D = [D] / 2 Offset 2D = [D] / 2 Tool offset (2) :

Offset 3D = [D] / 2 Offset 2D = [D] / 2

- ConicNoseMill (Conic Nose Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] ClearanceAngle (Clearance Angle) = [E] CuttingTopDiameter (Cutting Top Diameter) = [D] CuttingBottomDiameter (Cutting Bottom Diameter) = [B] Version 7.6.301.084




- ConicNoseBallMill (Conic Nose Ball Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] ClearanceAngle (Clearance Angle) = [E] CuttingTopDiameter (Cutting Top Diameter) = [D] CuttingBottomDiameter (Cutting Bottom Diameter) = [B] CornerRadius (Corner Radius) = [F] Version 7.6.301.084


Offset 3D = [F] Offset 2D = [B] / 2 Tool offset (2) :

Offset 3D = [F] Offset 2D = [B] / 2 This point is at Y=[F] Tool offset (3) :


- SpotFaceMill (Spot Face Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) OverLength (Over Length) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084



- BackSpotFaceMill (Back Spot Face Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) OverLength (Over Length) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084




- CounterboringMill (Counterboring Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.8.102.000




- CornerRoundingMill (Corner Rounding Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CornerRadius (Corner Radius) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.6.301.084


Offset 3D = 0 Offset 2D = ([B] / 2) - [D] Tool offset (2) :


- ChamferMill (Chamfer Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingAngle (Cutting Angle) = [E] CuttingTopDiameter (Cutting Top Diameter) = [D] CuttingBottomDiameter (Cutting Bottom Diameter) = [B]

Version 7.6.301.084 For this tool, you need to define 2 Tool Offset : Tool offset (1) :



- ReverseChamferMill (Reverse Chamfer Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingAngle (Cutting Angle) = [E] CuttingTopDiameter (Cutting Top Diameter) = [D] CuttingBottomDiameter (Cutting Bottom Diameter) = [B]

Version 7.6.301.084




- DoubleChamferMill (Double Chamfer Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingLength (Cutting Length) = [C] CuttingAngle (Cutting Angle) = [E] CuttingTopDiameter (Cutting Top Diameter) = [D] CuttingBottomDiameter (Cutting Bottom Diameter) = [B]

Version 7.6.301.084



Offset 3D = 0 Offset 2D = [D] / 2 Tool offset (3) :

Offset 3D = 0 Offset 2D = [D] / 2 Tool offset (4) :


- DiscMill (Disc Mill) CuttingEdgeOrigin (Cutting Edge Origin) ) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CuttingWidth (Cutting Width) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B] Version 7.8.102.000




- RadiusedStaggeredTeethMill (Radiused Staggered Teeth Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) CornerRadiusTop (Corner Radius Top) = [E] CornerRadiusBottom (Corner Radius Bottom) = [F] CuttingWidth (Cutting Width) = [D] CuttingLength (Cutting Length) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.8.102.000




Offset 3D = [E] Offset 2D = [B] / 2 Tool offset (4) :

Offset 3D = [E] Offset 2D = [B] / 2

- SpecialMill (Special Mill) CuttingEdgeOrigin (Cutting Edge Origin) MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) RevolutionProfile (Revolution Profile) Version 7.6.301.084


Offset 3D = yy Offset 2D = xx

- ConstantReamer (Constant Reamer) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) OverLength (Over Length) FluteLength (Flute Length) = [D] DepthReaming (Depth Reaming) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084



- BoringBar (Boring Bar) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] MaximumRampAngle (Maximum Ramp Angle) CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) OverLength (Over Length) FluteLength (Flute Length) ) = [D] DepthReaming (Depth Reaming) = [C] CuttingDiameter (Cutting Diameter) = [B]

Version 7.6.301.084



- Tap (Tap) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) LeftHand (Left-Hand) NominalDiameter (Nominal Diameter) = [B] OverLength (Over Length) FluteLength (Flute Length) = [E] DepthTapping (Depth Tapping) = [C] Norm (Norm) Pitch (Pitch) = [D] Version 7.6.301.084



- ExternalThreadMill (External Thread Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) NumberOfThreadTeeth (Number Of Thread Teeth) DepthThreading (Depth Threading) = [C] CuttingDiameter (Cutting Diameter) = [B] Pitch (Pitch) = [D] ThreadProfile (Thread Profile) Version 7.6.301.084



- InternalThreadMill (Internal Thread Mill) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) NumberOfToolTeeth (Number Of Tool Teeth) LeftHand (Left-Hand) NumberOfThreadTeeth (Number Of Thread Teeth) DepthThreading (Depth Threading) = [C] CuttingDiameter (Cutting Diameter) = [B] Pitch (Pitch) = [D] ThreadProfile (Thread Profile) Version 7.6.301.084



- ExternalTurn (External Turn) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle (Alpha)) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CuttingEdgeSize (Cutting Edge Size) = [B] CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) HandOfTool (Hand Of Tool (R/L/N)) CornerRadius (Corner Radius) = [D]

Version 7.6.301.084

A) If the tool can manage only 1 radius, you need to define 1 Tool Offset

Offset 3D = 0 Offset 2D = [D] For a Left turn tool, Offset Description = Left For a Right turn tool, Offset Description = Right For a Neutral turn tool, Offset Description = Neutral

LEFT

and Neutral RIGHT

B) If the tool can manage 2 radius, you need to define 2 Tool Offset

In this case, the CuttingEdgeOrigin ( frame [A] ) is on the tool offset (1). Tool offset (1) : For a Left turn tool, Offset Description = Left For a Right turn tool, Offset Description = Right Offset 3D = 0 Offset 2D = [D] Tool offset (2) : Offset Description = Top Offset 3D = 0 Offset 2D = [D]

LEFT RIGHT

- InternalTurn (Internal Turn) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle (Alpha)) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CuttingEdgeSize (Cutting Edge Size) = [B] CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) HandOfTool (Hand Of Tool (R/L/N)) CornerRadius (Corner Radius) = [D]

LEFT Right And NEUTRAL

Version 7.6.301.084

A) If the tool can manage only 1 radius, you need to define 1 Tool Offset For a Left turn tool, Offset Description = Left For a Right turn tool, Offset Description = Right For a Neutral turn tool, Offset Description = Neutral Offset 3D = 0 Offset 2D = [D]

C) If the tool can manage 2 radius, you need to define 2 Tool Offset In this case, the CuttingEdgeOrigin ( frame [A] ) is on the tool offset (1).

Tool offset (1) : For a Left turn tool, Offset Description = Left For a Right turn tool, Offset Description = Right Offset 3D = 0

Offset 2D = [D] Tool offset (2) : Offset Description = Top Offset 3D = 0 Offset 2D = [D]

LEFT RIGHT

- ExternalGroove (ExternalGroove) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CuttingEdgeSize (Cutting Edge Size) CuttingEdgeShape (Cutting Edge Shape) HandOfTool (Hand Of Tool (R/L/N)) CuttingEdgeDepth (Cutting Edge Depth) = [D] CuttingEdgeWidth (Cutting Edge Width) = [B] CornerRadius2 (Corner Radius Right) = [H] CornerRadius1 (Corner Radius Left) = [G]

LEFT RIGHT Insert R = NEUTRAL

And NEUTRAL

Version 7.6.301.084 For this tool, you need to define 2 Tool Offset : Tool offset (1) :

Offset 3D = 0 Offset 2D = [G] Tool offset (2) :

Offset 3D = 0 Offset 2D = [H]

- InternalGroove (Internal Groove) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle) ) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CornerRadius2 (Corner Radius Right) = [H] CornerRadius1 (Corner Radius Left) = [G] CuttingEdgeSize (Cutting Edge Size) CuttingEdgeShape (Cutting Edge Shape ) HandOfTool (Hand Of Tool (R/L/N)) CuttingEdgeDepth (Cutting Edge Depth) = [D] CuttingEdgeWidth (Cutting Edge Width) = [B]

LEFT RIGHT

Left Insert R Right Insert R

Version 7.6.301.084


Offset 3D = 0 Offset 2D = [G]

Tool offset (2) :


- FrontalGroove (Frontal Groove) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle) = [E] InsertThickness (Insert Thickness) = [C] GrooveExternalDiameter (Groove External Diameter) GrooveInternalDiameter (Groove Internal Diameter) CuttingEdgeSize (Cutting Edge Size) CuttingEdgeShape (Cutting Edge Shape) HandOfTool (Hand Of Tool (R/L/N)) CuttingEdgeDepth (Cutting Edge Depth) = [D] CuttingEdgeWidth (Cutting Edge Width) = [B] CornerRadius2 (Corner Radius Right) = [H] CornerRadius1 (Corner Radius Left) = [G]

LEFT RIGHT Insert R = NEUTRAL

And NEUTRAL

Version 7.6.301.084


Offset 3D = 0 Offset 2D = [G] Tool offset (2) :


- ExternalThread (External Thread) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle (Alpha)) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CuttingEdgeSize (Cutting Edge Size) CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) HandOfTool (Hand Of Tool (R/L/N)) Pitch (Pitch) ThreadProfile (Thread Profile)

LEFT RIGHT

Version 7.6.301.084

For this tool, you need to define 1 Tool Offset For a Left Thread tool, Offset Description = Left For a Right Thread tool, Offset Description = Right Offset 3D = 0 Offset 2D = 0

- InternalThread (Internal Thread) CuttingEdgeOrigin (Cutting Edge Origin) = frame [A] CoolantNozzle (Coolant Nozzle) ClearanceAngle (Clearance Angle (Alpha)) = [E] InsertThickness (Insert Thickness) = [C] EntryDiameter (Entry Diameter) = [F] CuttingEdgeSize (Cutting Edge Size) CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) HandOfTool (Hand Of Tool (R/L/N)) Pitch (Pitch) ThreadProfile (Thread Profile)

LEFT RIGHT

Version 7.6.301.084

For this tool, you need to define 1 Tool Offset For a Left Thread tool, Offset Description = Left For a Right Thread tool, Offset Description = Right Offset 3D = 0 Offset 2D = 0

- BallTouch (Ball Touch) TouchOrigin (Touch Origin) = frame [A] TouchDiameter (Touch Diameter) = [B] WorkLength (Work Length) = [C]


Offset 3D = 0 Offset 2D = 0

- ClampGroove (Clamp Groove) CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) CuttingEdgeSize (Cutting Edge Size) CuttingEdgeWidth (Cutting Edge Width) CuttingEdgeDepth (Cutting Edge Depth) CornerRadius2 (Corner Radius Right) CornerRadius1 (Corner Radius Left) InsertThickness (Insert Thickness) ClearanceAngle (Clearance Angle (Alpha))

- ClampThread (Clamp Thread) CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) CuttingEdgeSize (Cutting Edge Size) CornerRadius (Corner Radius) InsertThickness (Insert Thickness) ClearanceAngle (Clearance Angle (Alpha)) ThreadProfile (Thread Profile) Pitch (Pitch)

- ClampInsert (Clamp Insert) CuttingEdgeShape (Cutting Edge Shape(A,B,C..X)) CuttingEdgeSize (Cutting Edge Size) CornerRadius (Corner Radius) InsertThickness (Insert Thickness) ClearanceAngle (Clearance Angle (Alpha))

- ToolingHolder (Tooling Holder) ToolingSystemFrame (Tooling System Frame) ToolingSystemName (Tooling System Name) ToolingSystemType (Tooling System Type) ToolingSystemSize (Tooling System Size)

- ToolingShank (Tooling Shank) ToolingSystemFrame (Tooling System Frame) = [A] ToolingSystemName (Tooling System Name) ToolingSystemSize (Tooling System Size)

For Milling :

For Turning, the rule is : Imagine a turning machine with 1 chuck and 1 simple turret. On the turret, in T1, do a translation of the part origin. When you put the tool on this frame [A], we must see the insert of the tool. With this method, you can fix the Z and X of the “Tooling System Frame”.

So exemple : Left Turn tool :

Right Turn tool :

And generally ( except for Flash Tool) , in the Frame [A], the frame of the tool type (ex “External turn” ) must be at Y=0

- ClampingInsert (Clamping Insert) ClampingSystemName (Clamping System Name) ClampingSystemFrame (Clamping System Frame) ClampingSystemSize (Clamping System Size) ClampingSystemType (Clamping System Type) ClampingSystemName (Clamping System Name) ClampingSystemFrame (Clamping System Frame) ClampingSystemSize (Clamping System Size)

- CylindricalToolingShank (Cylindrical Tooling Shank) MaximalDistance (Maximal Distance) MinimalDistance (Minimal Distance) InitialDistance (Initial Distance) ShankDiameter (Shank Diameter) ToolingSystemFrame (Tooling System Frame)

- CylindricalToolingHolder (Cylindrical Tooling Holder) ShankMinimalDiameter (Shank Minimal Diameter) ShankMaximalDiameter (Shank Maximal Diameter) ToolingSystemName (Tooling System Name) ToolingSystemType (Tooling System Type)

- SquareToolingShank (Square Tooling Shank) MaximalDistance (Maximal Distance) MinimalDistance (Minimal Distance) InitialDistance (Initial Distance) ShankWidth (Shank Width) ShankHeight (Shank Height) ToolingSystemFrameLeft (Tooling System Frame Left) ToolingSystemFrameRight (Tooling System Frame Right)

- SquareToolingHolder (Square Tooling Holder) ShankHeight (Shank Heigth) ToolingSystemFrame (Tooling System Frame) ToolingSystemType (Tooling System Type)

- ToolOffset (Tool Offset) PointCompensation (Point Compensation) = Origin of X, Y plane PlaneCompensation (Plane Compensation) = Plane X,Y = [F] Offset2d (Offset 2d) = [C] Offset3d (Offset 3d) = [D] PlungeDirection (Plunge Direction) = [A] RespectDirection (Respect Direction) = [B] OffsetDescription (Offset Description (Tip,Top,Bottom,Left,Rigth,...))

- CollisionAnalysisRevolutionShape (Collision Analysis Revolution Shape) Revolute Section (Revolute Section)

- CollisionAnalysisShape (Collision Analysis Shape) Shape (Shape)

- Tag (Tag) Tag (Tag)

- CuttingShape (Cutting Shape) Shape (Shape)

- CuttingRevolutionShape (Cutting Revolution Shape) Revolution Section (Revolution Section)

ClampingSystemFrame Clamping System Frame.

Type : TopSolid.Kernel.DB.D3.Frames.PublishingFrameEntity

ClampingSystemName Clamping System Name.

Type : TopSolid.Kernel.DB.Parameters.PublishingTextParameterEntity

ClampingSystemSize Clamping System Size.

Type : TopSolid.Kernel.DB.Parameters.PublishingRealParameterEntity (Length)

ClampingSystemType Clamping System Type.


ClearanceAngle Clearance Angle = [E]

Type : TopSolid.Kernel.DB.Parameters.PublishingRealParameterEntity (Angle)

CoolantNozzle Coolant Nozzle.

Type : TopSolid.Kernel.DB.Parameters.PublishingBooleanParameterEntity

CornerRadius Corner Radius = [D]


CornerRadius1 Left Corner Radius of Groove Insert = [G]


CornerRadius2 Right Corner Radius of Groove Insert = [H]


CuttingAngle Cutting Angle = [E]

E = 45° E = 90°


CuttingBottomDiameter Cutting Bottom Diameter = [B]


CuttingDiameter Cutting Diameter = [B]


CuttingEdgeDepth Cutting Edge Depth = [D]


CuttingEdgeOrigin Cutting Edge Origin = Frame [A]


CuttingEdgeShape Cutting Edge Shape(A,B,C..X).


CuttingEdgeSize Cutting Edge Size


CuttingEdgeWidth Cutting Edge Width = [B]


CuttingLength Cutting Length = [C]


CuttingTopDiameter Cutting Top Diameter = [D]


CuttingWidth Cutting Width for T Slot cutters = [D]


DepthDrilling Depth Drilling.


DepthReaming Depth Reaming.


- DepthTapping Depth Tapping.


- DepthThreading Depth Threading.


- EntryDiameter Entry Diameter.


FluteLength Flute Length.


GrooveExternalDiameter Groove External Diameter.


GrooveInternalDiameter Groove Internal Diameter.


HandOfTool Hand Of Tool (R/L/N).


- InitialDistance Initial Distance.


- InsertThickness Insert Thickness.


LeftHand Left-Hand.

Type : TopSolid.Kernel.DB.Parameters.PublishingBooleanParameterEntity

- MaximalDistance Maximal Distance.


MaximumRampAngle Maximum Ramp Angle.


- MinimalDistance Minimal Distance.


- NominalDiameter Nominal Diameter.


- Norm Norm.


- NumberOfThreadTeeth Number Of Thread Teeth.

Type : TopSolid.Kernel.DB.Parameters.PublishingIntegerParameterEntity

- NumberOfToolTeeth Number Of Tool Teeth.

Type : TopSolid.Kernel.DB.Parameters.PublishingIntegerParameterEntity

- Offset2d Offset 2d.


Offset 2D is a radius value.

- Offset3d Offset 3d. Type : TopSolid.Kernel.DB.Parameters.PublishingRealParameterEntity (Length) Offset 3D is a radius value.

- OffsetDescription Offset Description (Tip,Top,Bottom,Left,Rigth,...). Type : TopSolid.Kernel.DB.Parameters.PublishingTextParameterEntity It’s a comment. You can write what you want. But if you want a translation in a another language, you must use this words : Bottom Center Left Right Tip Top Bottom Center Top Center Neutral Undefined

- OverLength Over Length.


- Pitch Pitch.


- PlaneCompensation Plane Compensation.

Type : TopSolid.Kernel.DB.D3.Planes.PublishingPlaneEntity

- PlungeDirection

Plunge Direction. Look the green arrow

Type : TopSolid.Kernel.DB.D3.Axes.PublishingAxisEntity

For milling tool :

For External Turn Tool :

LEFT

and Neutral RIGHT

For Internal Turn Tool :

For External Groove Tool :

LEFT

and Neutral RIGHT

For Internal Groove Tool :

… For External Thread Tool

For Internal Thread Tool

LEFT RIGHT

LEFT RIGHT

- PointCompensation Point Compensation.

Type : TopSolid.Kernel.DB.D3.Points.PublishingPointEntity

- RespectDirection

Respect Direction. Look the Magenta arrow.

Type : TopSolid.Kernel.DB.D3.Axes.PublishingAxisEntity

For milling tool :

For External Turn Tool :

LEFT

and Neutral RIGHT

For Internal Turn Tool :

For External Groove Tool and Frontal Groove Tool:

LEFT

and Neutral RIGHT

For Internal Groove Tool :

.. For External Thread Tool

For Internal Thread Tool

LEFT RIGHT

LEFT RIGHT

Revolute Section Revolute Section.

Stock update and Analysis collision

Type : TopSolid.Kernel.DB.D3.Sections.PublishingSectionEntity

Revolution Section Revolution Section.



RevolutionProfile Revolution Profile.



ShankDiameter Shank Diameter.


ShankHeight Shank Height.


ShankMaximalDiameter Shank Maximal Diameter.


ShankMinimalDiameter Shank Minimal Diameter.


ShankWidth Shank Width.


Shape Shape for stock update or analysis collision.

Type : TopSolid.Kernel.DB.D3.Shapes.PublishingShapeEntity

Tag Tag.


ThreadProfile Thread Profile.


TipAngle Tip Angle.


ToolingSystemFrame Tooling System Frame.


ToolingSystemFrameLeft Tooling System Frame Left.


ToolingSystemFrameRight Tooling System Frame Right.


ToolingSystemName Tooling System Name.


ToolingSystemSize Tooling System Size.


ToolingSystemType Tooling System Type.


Cutting Tool Material Category Inside TopSolid’Cam , we have this list :

Inside xml file, we have : <PublishingEnumerationParameterEntity> <Id>21</Id> <Name>Cutting Tool Material Category</Name> <Value> <Guid>b50e5d21-e504-4a4f-8c60-727fb2a151d0</Guid> <Id>0</Id> //None </Value> <PublishingName>CuttingToolMaterialCategory</PublishingName> </PublishingEnumerationParameterEntity> The <Guid> b50e5d21-e504-4a4f-8c60-727fb2a151d0 : number is fixed. The <Id> value is : 0:None 1:Unclassified 2:HighCarbonSteel 3:HighSpeedSteel 4:CementedCarbide 5:CoatedCarbide 6:Ceramic 7:Diamond

Tool example 1 : Multi-Diameter Drill solution 1 Example :

You need to define 2 functions “Twist Drill” :

You need to define 4 Tool Offset : Tool offset (1) : Offset 3D = 0 Offset 2D = 0 Tool offset (2) : Offset 3D = 0 Offset 2D = [B1] / 2 Tool offset (3) : Offset 3D = 0 Offset 2D = [B1] / 2 Tool offset (4) : Offset 3D = 0 Offset 2D = [B2] / 2 In this case, we can use :

- the 2 functions (TD_1 and TD_2) to do Drilling operation - only TD_1 to do Counter sinking operation

To have a good stock update and to be able to use this tool in Verify, you must define only 1 “Cutting Revolution Shape” , so you must have only 1 sketch , like this :

Tool example 1 : Multi-Diameter Drill solution 2 Example :


You need to define 4 Tool Offset : Tool offset (1) : Offset 3D = 0 Offset 2D = 0 Tool offset (2) : Offset 3D = 0 Offset 2D = [B1] / 2 Tool offset (3) : Offset 3D = 0 Offset 2D = 0 Tool offset (4) : Offset 3D = 0 Offset 2D = [B2] / 2 In this case, we can use the 2 functions (TD_1 and TD_2) to do

- Drilling operation - Counter sinking operation

To have a good stock update and to be able to use this tool in Verify, you must define only 1 “Cutting Revolution Shape” , so you must have only 1 sketch , like this :

Tool example 2 : Multi-Diameter Drill Example :


You need to define 4 Tool Offset : Tool offset (1) : Offset 3D = 0 Offset 2D = 0 Tool offset (2) : Offset 3D = 0 Offset 2D = [B1] / 2 Tool offset (3) : Offset 3D = 0 Offset 2D = [B1] / 2 Tool offset (4) : Offset 3D = 0 Offset 2D = [B2] / 2 To have a good stock update and to be able to use this tool in Verify, you must define only 1 “Cutting Revolution Shape” , so you must have only 1 sketch , like this :

Documentation TopSolid’Cam - Amazon S3...TopSolid ® is a product name of Missler Software. The...

Documents

Transcript of Documentation TopSolid’Cam - Amazon S3...TopSolid ® is a product name of Missler Software. The...