MDWFS014LSO

OWNER'S MANUAL

Dish Washer

Inside you will find many helpful hints on how to use and maintainDish Washer cooler properly. Just a little preventive care on your partcan save you a great deal of time and money over the life of your

. You will find many answers to common problems in theFrequently asked questions . If you read this section you may notneed to call for service.

Dish Washer" "

To review the section on troubleshooting Tips

will help you to solve some common problemsby yourself .

Dear Customer,

Please carefully read this manual before using thedishwasher, it will help you to use and maintain thedishwasher properly.

Pass it on to any subsequent owner of the appl iance.

This manual contains sections on safety Instructions,Operating Instructions, Instal lation Instruc tions andTroubleshooting Tips, etc.

The manufacturer, following a pol icy of constantdevelopment and updating of the product, maymake modifications without giving prior notice.

This user manual shall also be got from themanufacturer or responsible vendor.

Keep it to refer to it at a later date.

If you can not solve the problems by yourself ,

please ask for the help of professional technicians.

Dishwasher Features.. .... ......... .... ........ ......... ...6

A Water Softener...... ............. ........ ..... .... ...... 7、

Attention before or after loading the DishwasherBaskets............ .......... ........... ...................... . 12

Filtering System...... .......... ..... .... ..... .......... .....16Caring for the Dishwasher..... ..... .......... ..... .... ..17

B Loading the Salt into the Softener.......... .......8、

C Fill the Rinse Aid Dispenser.........................8、

D Function of Detergent . ......... .......... ..... .... ....9、

Loading the upper Basket.......... ......... ........ ....13Loading the Lower Basket..... ..... .......... ......... ..13

Cutlery Basket........ .......................... ......... .. 13

Wash Cycle Table.... .......... ..... .......... ..... .... .....14Turning on the Appliance....... .........................15Change the program...... ..... ......... .......... .........15

At the end of the Wash Cycle........ ......... ......... .15

Positioning the Appliance...... ...................... ...18

Water Connection.... ......... .......... ...................19

About Power Connection.... ......... .......... .........18

Start of dishwasher........................................20

Before cal ling for se rvice.... .... ........... ... .... .......21Error codes................................... ................22

Technical information.....................................23

Control Panel.... .... ............... ............... .............6

This appliance is intended to be used in householdand similar applications such as:-staff kitchen areas in shops, offices and otherworking environments;-farm houses;-by clients in hotels, motels and other residential typeenvironments;-bed and breakfast type environments.This appliance can be used by children aged from 8years and above and persons with reduced physical,sensory or mental capabilities or lack of experienceand knowledge if they have been given supervisionor instruction concerning use of the appliance in asafe way and understand the hazards involved.Children shall not play with the appliance. Cleaningand user maintenance shall not be made by childrenwithout supervision. For EN60335-1This appliance is not intended for use by persons(including children )with reduced physical, sensoryor mental capabilities, or lack of experience andknowledge ,unless they have been given supervisionor instruction concerning use of the appliance by aperson responsible for their safety. For IEC60335-1This appliance is for indoor use only, for householduse only.To protect against the risk of electrical shock, do notimmerse the unit, cord or plug in water or other liquid.Please unplug before cleaning and maintenance theappliance .Use a soft cloth moisten with mild soap, and then usea dry cloth to wipe it again.

（ ）

（ ）

When using your dishwasher,follow the precautions listed below:

This appliance must be earthed. In the event of amalfunction or breakdown, earthing will reduce the riskof anelectric shock by providing a path of leastresistance of electric current. This appliance is equippedwith a cord having an equipment-earthing conductor

and a grounding plug.The plug must be plugged into an appropriate outlet thatis installed and earthed in accordance with all localcodes and ordinances.Improper connection of the equipment-earthingconductor can result in the risk of an electric shock.Check with a qualified electrician or servicerepresentative if you are in doubt whether the applianceis properly grounded.Do not modify the plug provided with the appliance;If it does not fit the outlet.Have a proper outlet installed by a qualified electrician.Do not abuse, sit on, or stand on the door or dish rack of

the dishwasher.Do not operate your dishwasher unless all enclosurepanels are properly in place.Open the door very carefully if the dishwasher isoperating, there is a risk of water squirting out.Do not place any heavy objects on or stand on the doorwhen it is open. The appliance could tip forward.When loading items to be washed:1) Locate sharp items so that they are not likely todamage the door seal;

2) Warning: Knives and other utensils with sharp pointsmust be loaded in the basket with their points down orplaced in a horizontal position.Check that the detergent powder is empty aftercompletion of the wash cycle.Do not wash plastic items unless they are markeddishwasher safe or the equivalent.For plastic items not so marked, check the manufacturer'srecommendations.Use only detergent and rinse additives designed foran automatic dishwasher.Never use soap, laundry detergent, or hand washingdetergent in your dishwasher.Children should be supervised to ensure that they do notplay with the appliance.The door should not be left open, since this could increasethe risk of tripping.If the supply cord is damaged, it must be replaced by themanufacturer or its service agent or a similarly qualifiedperson in order to avoid a hazard.During installation, the power supply must not beexcessively or dangerously bent or flattened.Do not tamper with controls.The appliance is to be connected to the water mains usingnew hose sets and that old hose-sets should not be reused.The maximum number of place settings to be washedis 14.The maximum permissible inlet water pressure is 1MPa.The minimum permissible inlet water pressure is 0.04MPa.

Dispose of the dishwasher packaging materialcorrectly.All packaging materials can be recycled.Plastic parts are marked with the standardinternational abbreviations:PE for polyethylene, e.g. sheet wrapping materialPS for polystyrene, e.g. padding materialPOM polyoxymethylene, e.g. plastic clipsPP polypropylene, e.g. Salt fillerABS Acrylonitrile Butadiene Styrene, e.g. ControlPanel .

Packaging material could be dangerous for children!For disposing of package and the appliance pleasego to a recycling centre. Therefore cut off the powersupply cable and make the door closing deviceunusable.Cardboard packaging is manufactured from recycledpaper and should be disposed in the waste papercollection for recycling.By ensuring this product is disposed of correctly, youwill help prevent potential negative consequencesfor the environment and human health, which couldotherwise be caused by inappropriate waste handlingof this product.For more detailed information about recycling of thisproduct, please contact your local city office and yourhousehold waste disposal service.DISPOSAL: Do not dispose this product as unsortedmunicipal waste. Collection of such waste separatelyfor special treatment is necessary.

For detailed operating method read the corresponding content on the instruction manual.

With each wash cycle.

Compartment

For programs with pre-wash only.

(Follow the user instructions!)

Electric indicator on control panel (if provided).Check the rinse aid level

(On models with water softener system only.)Electric indicator on control panel (if provided).If there is no salt warning light in the control panel(for some models), you can estimate when to fill the salt intothe softener by the number of cycles the dishwasher has run.

Check the regenerationsalt level

Load the baskets

Select a program

Turn on the water tap and press the Start/Pause button. The machine will start workingafter about 10 seconds.

Running the dishwasher

Switch off the appliance

Turn off the water tap,unload the baskets

Fill the detergent dispenser

Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handlingthe dishes and utensils while they are still hot and more susceptible to break.They will also dry better.Unload the appliance, starting from the lower basket.

Changing the program

Add forgotten dishes in thedishwasher.

Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,then load the baskets. Refer to the dishwasher loading instructions.

Close the door,press the program button until the selected program lights up.( See the section entitled Operation instruction )“ ”

When the working cycle has finished, the buzzer of thedishwasher will sound 8 times, then stop.Turn off the appliance using the Power button.It will shut off automaticly after 30 minutes without any operation

If the appliance is switchedoff during a wash cycle.

Open the door carefully.Hot steam may escapewhen the door is opened!

If the appliance is switched off during a wash cycle, when switchedon again, please re-select the washing cycle and operate the dishwasheraccording to the original Power-on state ).

Switch on the appliance Press the Power switch button to switch on the appliance, Open the door.

1.Press the start/pause button to stop the machine.2.Open the door.3.Add the forgotten dishes.4.Close the door, then press the start/pause button, the dishwasher willstart running again after 10 seconds.

1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergentmay have already been released and the water already drained. If this is the case, the detergentdispenser must be refilled.2. Press the Start/Pause button ,then press the program button more than 3 seconds to cancel therunning program.3. Select a new program.4. Restart the dishwasher.

before using it for the first time.

To get the best performance from your dishwasher, read all operating instructions

1. On/Off Button: to switch On/Off the appliance;2.

4

Child lock function: press Delay button and Half- loadbutton simultaneously to lock the program;

3.Delay Button : Press the button to add the delay time;.Alt Button: Dual zone wash function, press the buttonto select either upper basket or lower basket loaded;

5.Display screen: to show the reminding time and thestate(running state, delay time etc );Rinse Aid indicator:Indicates when the dispenser needs to be refilled;Add salt indicator:Indicates when the dispenser needs to be refilled;

Child lock indicator:Water faucet indicator:Extra drying indicators:Extra cleaning indicators:

Upper spray indicator:Lower spray indicator:

6.Start /Pause button: To start the selected washingprogram or pause the washing program when themachine is working starting up or not;

7.Extra dryingand extra cleaning Button : To select extradrying and exra cleaning function.Extra drying function Only be used with Intensive,Normal, ECO,Glass,90min.),extra cleaning functionOnly be used with Intensive, Normal, ECO,Glass.);

8.Program Button : To Press the button to selectappropriate Program;

11 12

Back View

123

45

7

8

910

Front view

Lower basket

Salt container

Dispenser

Cup shelf

Spray arms

Filter assembly

Inlet pipe connector

Drain pipeUpper basket

Cutlery rack

Top spray arm1 Inner pipe

5

6

7

89

10

1211

32

4

6

The water softener must be set manually, using the water hardness dial.The water softener is des igned to remove minerals and salts from the water, which would havea detrimental or adverse effect on the operation of the appliance.The higher the content of these minerals and salts, the harder your water is.The softener should be adjusted according to the hardness of the water in your area. Your local Water Authoritycan advise you on the hardness of the water in your area.

Adjusting Salt ConsumptionThe dishwasher is designed to allow for adjustment in the amount of sa lt consumed based on the hardness ofthe water used. This is intended to optimise and customise the level o f salt consumption.

WATER SOFTENERThe hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits willform on the dishes and utensils.The appliance is equipped with a special softener that uses a salt container specifically des igned to eliminatelime and minera ls from the water.

Contact your local water board for information on the hardness of your water supply.

If your model does not have any water softener, you may skip this section.

Clark: British degree

fH: French degree

dH: German degree

dH=1.25 Clarke=1.78 fH=0.178mmol/l1

The manufactory setting: H4 (EN 50242)

Before using your dishwasher for the first time:

A. Set the water softener

B. Add 1.5Kg dishwasher salt and then full fi l l the salt container with water

C. Fill the rinse aid dispenser

D. Fill in detergent

dH mmol/l

0~90~5 0~0.94 H1 0

10-206-11 1.0-2.0 H2 9

21-3012-17 2.1-3.0 H3 12

H4 20

fH

0~6

7-14

15-21

Clarke

WATER HARDNESS

Selector PositionSalt consumption(gram/cycle)

18-22 31-40 22-28 3.1-4.0

41-6023-34 4.1-6.0 H5 30

H6 60

29-42

35-55 61-98 43-69 6.1-9.8

1. Switch on the appliance;2. Press the Start/Pause button for more than 5 seconds to start the watersoftener set model within 60seconds after the appliance wasswitched on;3. Press the button to select the proper set according toyour local environment, the sets will change in the followingsequence: H1->H2->H3->H4->H5->H6;4. Press the to end the set up model.

Start/Pause

On/Off button

Please follow the steps below for adjustment in salt consumption.

1. The salt container must only be refil led when the salt warning light in the control panel comes on.Depending on how well the salt dissolves, the salt warning light may still be on even though thesalt container is filled.If there is no salt warning light in the control panel (for some Models),you can estimate when to f illthe salt into the softener by the cycles that the dishwasher has run.

2. If there are spills of the salt , a soak or a rapid program should be run to remove the excessive salt.

Always use the salt intended for use with dishwasher.The salt container is located beneath the lower basket and should be fil led as explainedin the following:

Attention!Only use salt specif ically designed for the use in dishwashers! Every other type ofsalt not speci fically designed for the use in a dishwasher, especially table salt, willdamage the water softener. In case of damages caused by the use of unsuitablesalt the manufacturer does not give any warranty nor is liable for any damages caused.

Only fil l wi th salt just before starting one of the complete washing programs.This wi ll prevent any grains of salt or salty water, which may have been spilled,remaining on the bottom of the machine for any period of time, which may causecorrosion.

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which canleave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher isdesigned to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.To fi l l the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completelyblack. The volume of the rinse aid container is about 110ml.

Rinse Aid Dispenser

Function of Rinse AidRinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spo t and streak free drying.

Attention!Only use branded rinse aid for dishwasher. Never fi ll the rinse aid dispenser with any other substances(e.g. Dishwasher cleaning agent, liquid detergent). Th is would damage the app liance.

Full fil l the salt container with water,It is normal for a small amount of water to come out of thesal t container.

A After the lower basket has been removed, unscrew and remove the cap from the salt container.

B Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.

C

D Af ter fil ling the container , screw the cap t ightly back clockwise.E The sal t warning light wil l stop being after the salt container has been fi lled with sa lt .

F Immediately after f il ling the salt into the salt container, a washing program should be startedprogram Otherwise the filter system, pump or other important parts of the machine may be damagedby salty water. This is out of warranty.

(We suggest to use a short).

To open the dispenser, turn the cap to the "open" (left) arrow and l ift it out.

Pour the rinse aid into the dispenser, being careful not to overfill .

Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

Adjusting Rinse Aid Dispenser

The rinse aid dispenser has six or four settings. Always start with the dispenserset on "4". If spots and poor drying are a problem, increase the amount of r inseaid dispensed by removing the dispenser lid and rotating the dial to "5". If thedishes stil l are not drying properly or are show spots, adjust the dial to the nexthigher lever until your dishes are spot-free. The recommended setting is "4".(Factory value is "4".)

Increase the dose if there are drops of water or lime spots on the dishes after washing.Reduce i t i f there are sticky whitish stains on your dishes or a bluish film on glassware orknife blades.

123

As the rinse aid d iminishes, the size of the black doton the rinse aid level indicator changes, as illustra ted below.

Full3 / 4 full1 / 2 full1 / 4 full - Should refill to eliminate spottingEmpty

When to Refill the Rinse Aid DispenserIf there is no rinse-aid warning light in the control panel, you can est imate the amount from the colourof the optical level indicator C located next to the cap. When the rinse-aid container is full, the wholeindicator wil l be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never letthe rinse aid level fall 1 / 4 full .

during the next wash. Don't forget to replace the cap before you close dishwasher door.

Clean up any rinse aid spil led while during filling with an absorbent cloth to avoid excessive foaming

Detergents with its chemical ingredients are necessary to remove dirt, c rush dirt and transport it out of the dishwasher.Most of the commercial qual ity detergents are suitable for this purpose.

" "

Proper Use of DetergentUse only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.Don't put powdered detergent into the dispenser until you're ready to wash dishes.

Attention!

Amount of Detergent to Use

Based on their chemical composition, detergents can be split in two basic types:

Detergent tablets of different brands disso lve at di fferent speeds. For this reason somedetergent tablets cannot dissolve and develop their full cleaning power during shortprograms. Therefore please use long programs when using detergent tablets, toensure the complete removal of detergent residuals.

The dispenser must be refilled before the start of each wash cycle following the instructionsprovided in the wash cycle table . Your dishwasher uses less detergent and rinse aid thanConventional dishwasher. Generally, only one tablespoon of detergent is needed fora normal wash load. More heavily soiled items need more detergent. Always add thedetergent just before starting the dishwasher, otherwise it could get damp and will notdissolve properly.

Concentrated Detergent

Detergent Tablets

Detergent Dispenser

conventional, alkaline detergents with caustic componentslow alkaline concentrated detergents with natural enzymes

Normally new pulverised detergent is without phosphate. Thus the water softener function ofphosphate is not given. In this case we recommend to fill salt in the salt container even when

the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard wateroften white spots appear on dishes and glasses. In this case please add more detergent to reachbetter results. Detergents without chlorine do only bleach a little. Strong and coloured spots wil l notbe removed completely. In this case please choose a program with a higher temperature.

°

DetergentsThere are 3 sorts of detergents

1.With phosphate and with chlorine2.With phosphate and without chlorine3.Without phosphate and without chlorine

Always add the detergent just before starting each wash cycle.Only use branded detergent aid for dishwasher.

If the lid is closed: press release button. The lid will spring open.

Dishwasher detergent is corrosive!Take care to keep it out of reach of children.

Fill the detergent dispenser with detergent.The marking indicates the dosing levels , asillustrated on the right:

The place of main wash cycle detergent placed.

The place of pre-wash cycle detergent placed.

Please observe the manufacturers dosing and storageRecommendations as stated on the detergent packaging.

Close the lid and press until it locks in place.

If the dishes are heavily soiled, place an additiona ldetergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.

A

B

Fill in Detergent

You find information about the amount of detergent for the single program on the last page.

Please aware, that according to the level soiling and the specific hardness of water d ifferences are possible.

Please observe the manufacturer's recommendations on the detergent packaging.

A B

Cutlery with wooden, horn china ormother-of-pearl handlesPlast ic items that are not heat resistantOlder cut lery with glued parts that are nottemperature resistantBonded cutlery items or dishesPewter or copper itemsCrystal glassSteel items subject to rustingWooden plattersItems made from synthetic fibres

Some types of glasses can becomedull after a large number of washes

Silver and aluminum parts have atendency to discolour during washing

Glazed patterns may fade if machinewashed frequently

Are not suitable Are of limited suitability

Dishes and items of cutlery must not lie inside one another, or cover each other.To avoid damage to glasses, they must not touch.Load large items which are most difficult to clean into the lower basket.The upper basket is designed to ho ld more delicate and lighter dishware such as glasses, coffeeand tea cupsLong bladed knives stored in an upright position are a potential hazard!Long and/or sharp items of cut lery such as carving knives must be positionedhorizontally in the upper basket.Please do not overload your dishwasher. This is important for good results and forreasonable consumption of energy.

Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so thatwater cannot collect in the container or a deep base.

Consider buying utensils which are identified as dishwasher-proof.Use a mild detergent that is described as 'kind to dishes'. If necessary, seek furtherinformation from the detergent manufacturers.For particular items, select a program with as low a temperature as possible.To prevent damage, do not take glass and cutlery out of the dishwasher immediatelyafter the program has ended.

(For best performance of the dishwasher, follow these loading guide lines.Features and appearance of baskets and cutlery baskets may vary from your model.)

Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.It is not necessary to rinse the dishes under running water.Place objects in the dishwasher in following way:1.Items such as cups, glasses, pots /pans, etc. are faced downwards.2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.3.All utensils are stacked securely and can not tip over.4.All utensils are placed in the way that the spray arms can rotate freely during washing.

Very small items should not be washed in the dishwasher as they could easily fall out of the basket.

To prevent water dripping from the upper basket into the lower basket, we recommend that youempty the lower basket first and then the upper basket.

The upper basket is designed to hold more delicateand lighter dishware such as glasses, coffee andtea cups and saucers, as well as plates, small bowlsand shallow pans (as long as they are not too dirty).Position the dishes and cookware so that they willnot get moved by the spray of water.

We suggest that you place large items and the mostdi fficult to clean items are to be placed into the lowerbasket: such as pots, pans, lids, serving dishes andbowls, as shown in the figure below. It is preferable toplace serving dishes and lids on the side of the racksin order to avoid blocking the rotation of the top sprayarm.

Pots, serving bowls, etc, must always be placed top down.

Deep pots should be slanted to allow water to flow out.

Please be reminded that:

The Bottom Basket features fo lding spikes so that larger or more pots and pans can be loaded.

Folding Spikes of Lower BasketFor better stacking of pots and pans,the spikes can be folded down asshow in the picture right.

Adjusting the Upper BasketThe height of the upper basket can be adjusted in order tocreate more space for large utensils both for the upper/lower basket. The height of the upper basket can beadjusted by placing the wheels on different height of therails. Long items, serving cutlery, salad servers and knivesshould be placed on the shelf so that they do not obstructthe rotation of the spray arms..

Folding back the cup shelivesFor better stacking of pots and pans,the spikes can be folded down asshow in the picture right.

Cutlery should be placed in the cutlery rack separatelyfrom each other in the appropriate positions, and domake sure the utensils do not nest together, this maycause bad performance.

Do not let any item extend through the bottom.Always load sharp utensils with the sharppoint down!

*EN 50242 : This program is the test cycle. The information for comparability testin accordance with EN 50242, as follows:

Capacity: settingPosit ion Upper basket: upper wheels on railsRinse aid setting: 6PI:0.49W; P :0.45W.o

14

Left-on mode duration: Power will be cut off automatically after program finished for 30 minutes.

Intensive

Normal

Rapid

35g

20g

Means: need to fill rinse into the Rinse-Aid Dispenser.( )

For normally soiled loads,such as , p lates,glassesand lightly soiled pans.

pots

For heaviest soi led crockery,and normally soiled potspans dishes etc with driedon soil ing.

、、

A shorter wash for light lysoiled loads that do notneed drying.

Prewash 50Wash 62RinseRinseRinse 65Drying

（ ℃）（ ℃）

（ ℃）

Prewash(45 )Wash (55 )RinseRinse (65 )Drying

℃℃

℃

PrewashWash (45 )Rinse(65 )Drying

℃℃

Wash (45 )RinseRinse (45 )

℃

℃

Wash 65RinseRinse (65 )Drying

（ ℃）

℃

(*EN 50242)

This is standard programme, it issuitable to clean normally soiledtableware and it is the most effic ientprogramme in terms of its combinedenergy and water consumption forthat type of tableware.

GlassPre-washwash(40 )RinseRinse(60 )Drying

℃

℃

For lightly soiled crockeryand glass

10~150.9~1.5150

Pre-wash (45 )Autowash(45-55 )RinseRinse (65 )Drying

℃℃

℃

Auto sensing wash, lightly,normally or heavi ly soi ledcrockery, with or with outdried-on food

Auto

185

195

175

40

1.3

0.93

1.6

0.75

17

14

10

11.5

90 12.51.35

115 0.87 14

(Or )3in15/30g

(Or )3in15/30g

(Or )3in15/30g

(Or )3in15/30g

Start ing a cycle wash

Draw out the lower and upper basket, load the dishes and push them back.It is commended to load the lower basket first, then the upper one (see the section ent itledLoading the Dishwasher ).Pour in the detergent (see the section entitled Salt, Detergent and Rinse Aid ).Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the speci ficat ionof the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.Close the door, press the P button, to switch on the machine.Press the program button , the wash program will be changed as follows direction:

If a program is selected, the response l ight will l ight. Then press the Start /Pause button, thedishwasher begins to start.

“ ”“ ”

ower

ECO->Glass->90min->Rapid->Auto->Intensive->Normal;

1

23

45

For normally soiled loadsthat need quick wash.

(Or )3in15/30g

When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn offthe appliance using the Power switch button, shut off the water supply and open the door of the dishwasher.Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while theyare still hot and more suscept ible to breakage. They will also dry better.

Switch Off the DishwasherThe program light is on but is not blinking, only in this case the programme has ended.

Power1.Switch off the dishwasher by pressing the button.2.Turn off the water tap!

Open the door carefully.Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutesbefore removing from the appliance.Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way theywill be cooler and the drying will be improved.

Unloading the dishwasherIt is normal that the dishwasher is wet inside.Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket ontothe dishes in the lower one.

If you open the door , the machine will pause. The program light willstop blinking and the buzzer will mooing every minute unless you close the door . Afteryou close the door ,the machine will keep on working after 10 seconds.

during a wash cycle

Premise:A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, thedetergent may have already been released, and the appliance may have already drained the wash water.

If this is the case, the detergent dispenser must be refil led (see the section ent itled " Loading theDetergent " ).

Press the Start/Pause button , the machine will be in standby state, press the program button more than3s then you can change the program to the desired cycle setting (see the section entitled " Starting a washcycle. . ." ).

1

2

A forgotten dish can be added any time before the detergent cup opens.

Add forgotten dishes.

Close the door

After the spray arms stop working,you can open the doorcompletely.

2

3

Open the door a little to stop the washing.

1 4

5

6

Press the Start/Pause button

Press the button, the dishwasher will runafter 10 seconds.

Start/Pause

When you press the Start/Pause button to pause during washing, the running indicator willstop blinking and the dishwasher will mooing every minute unless you press the

button to start.Start/Pause

If your model has broken remember function, the machine wil l go on to finish the selectedprogram .after the power cut

It is dangerous to open the door when washing,because the hot water may scald you.

The filter prevents larger remnants of food or other objects from getting inside the pump.The residues may block the filter, in this case they must be removed.

The fi lter system consists of a coarse filter,a flat (Main f ilter)

And a microfilter(Fine filter).

Food and soil part icles trapped in this filter are pulverized by a

specia l jet on the lower spray arm and washed down to drain.

Larger items, such as pieces of bones or glass, that could block

the drain are trapped in the coarse filter. To remove the i tems

caught by the filter, gently squeeze the tap on the top of this

fil ter and l ift out.

This filter holds soil and food residues in the sump area andprevents i t from being redeposit on the dishes during wash cycle.

Main filter 1

Coarse filter2

Fine filter 3

2

3

1

Filter assemblyThe filter efficientlyFor best performance and results, the filter must be cleaned regularly. this reason, it is a good idea toremove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter andcup under running water. To remove the fil ter device, pull the cup handle in the upward direct ion.

removes food particles from the wash water, allowing it to be recycled during the cycle.For

The dishwasher must never be used without the fi lters.Improper replacement of the f ilter may reduce the performance level of the applianceand damage dishes and utensils.

1

2

Step 1 Turn the filter in ant i-clockwise direction,：

Step 2 lift the filter assy up：

When following this procedure from step1 to step 2, the filter system will be removed;when following it from Step 2 to Step 1, the filter system will be installed.

The control panel can be cleaned by using a lightly dampened cloth.After cleaning, make sure to dry it thoroughly.

For the exterior, use a good appliance pol ish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Protect Against Freezing

1.Cut off the electrical power to the dishwasher.2.Turn off the water supply and disconnect the water inlet pipe from the water valve.3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)4.Reconnect the water inlet pipe to the water valve.5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.

please take frost protection measures on the dishwasher in winter. Every fter washing cycles,please operate as follows

time a：

Cleaning the Filter

Cleaning the Door

To clean the coarse fi lter and the f ine f ilter, use a c leaning brush. Reassemble the fi lter parts as shown in the figureson the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.

When cleaning the filters, don't knock on them. Otherwise, the filters could becontorted and the performance of the dishwasher could be decreased.

To clean the edge around the door, you should use only a soft warm, damp cloth.To avoid penetration of water into the door lock and electrical components, do notuse a spray cleaner of any kind.

Never use a spray cleaner to clean the door panel as it may damage the door lockand electrical components.

Abrasive agents or some paper towels should not be used because of the risk ofscratching or leaving spots on the stainless steel surface.

Cleaning the Spray Arms

I f your dishwasher cannot work because of the ice,

please contact professional service persons.

I t is necessary to clean the spray arms regularly for hardwater chemicals will clog the spray arm jets and bearings.

- Inspect the filters for blocking after every time the dishwasher has been used.- By unscrewing the coarse fi lter, you can remove the filter system. Remove any food remnants andclean the fi lters under running water.

Remarks:

The entire filter assembly should be cleaned once a week.

To remove the lower spray arm, pull out the spray arm upward.

To remove the upper spray arm, hold the nut, rotate the armclockwise to remove it.

Wash the arms in soapy and warm water and use a soft brush toclean the jets. Replace them after rinsing them thoroughly.

It is recommend that you run a wash cycle with thedishwasher empty and then remove the plug from thesocket, turn off the water supply and leave the door ofthe appliance slightly open. This will help the doorseals to last longer and prevent odours from formingwithin the appliance.

If the appliance must be moved, try to keep it in thevertical position. If absolutely necessary, it can bepositioned on its back.

One of the factors that cause odours to form in thedishwasher is food that remains trapped in the seals.Periodic cleaning with a damp sponge will prevent thisfrom occurring.

Before cleaning or performing maintenance, alwaysremove the plug from the socket.

To clean the exterior and rubber parts of the dishwasher,do not use solvents or abrasive cleaning products.Only use a cloth with warm soapy water.To remove spots or stains from the surface of theinterior, use a cloth dampened with water an a littlevinegar, or a cleaning product made speci fical ly fordishwashers.

Remove the Plug

No Solvents or Abrasive Cleaning

Moving the Appliance

Seals

After every wash, turn off the water supply to theappliance and leave the door slight ly open so thatmoisture and odours are not trapped inside.

After Every Wash When not in Use for a LongTime

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that canbe positioned either to the right or the left s ides to facilitate proper installation.

Once the appl iance is positioned for levelling, the height of the dishwashermay be altered via adjustment of the screwing level of the feet.

Ensure the voltage and frequency of the power being corresponds tothose on the rating plate. Only insert the plug into an electrica l socket which is earthedproperly. If the electrical socket to which the appl iance must be connected is notappropriate for the plug , replace the socket, rather than using a adaptors or the like asthey could cause overheating and burns.

Please look at the rating label to know the rat ing voltage and connect the dishwasher to the appropriate power supply.Use the required fuse 10 amp, time delay fuse or c ircui t breaker recommended and provide separate circuit servingonly this appliance.

For personal safety:Do not use an extension cord or an adapter plugwith this appliance.Do not, under any circumstances, cut or remove theearthingConnection from the power cord.

Connect the cold water supply hose to a threaded 3/4(inch) connector and make surethat it is fastened tight ly in place.I f the water pipes are new or have not been used for an extended period of time, let thewater run to make sure that the water is clear. This precaution is needed to avoid therisk of the water in let to be blocked and damage the appliance.

Please close the hydrant after using.

Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let i t run into the sink, making sure toavoid bending or crimping it. The top of the hose must be less than 1000mm.

A

CounterFront

Drain pipe

NOTEThe top of the hosemust be less than1000mm.

φ 40mm

B

The following things should be checked before starting the dishwasher.

The content of this manual is very helpful to the users.

After installation, please make sure to keep this manual.

1 The dishwasher is level and fixed properly

2 The inlet valve is open

3 Fill hose connections are fully tightened and not leaking

4 The wires are tightly connected

5 The power is switched on

6 The inlet and drain hoses are knotted

7 All packing materials and printings should be taken out from the dishwasher

Extension HoseIf you need a drain hose extension, make sure to use a similar drain hose.It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.

Water OutletConnect the water drain hose. The drain hose must be correct ly fit ted to avoid water leaks.Ensure that the water dra in hose is not kinked or squashed.

If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directlyinto the sink. It will be necessary to drain excess water from hoses into a bowl or sui tablecontainer that is held outside and lower than the sink.

How to Drain Excess Water From Hoses

Syphon ConnectionThe waste connection must be at a he ight less than 1000 mm (maximum) from the bottom of the dish.The water drain hose should be fixed .

Fuse blown, or the

circuit breaker acted

Replace fuse or reset circuit breaker. Remove any other

appliances sharing the same circuit with the dishwasher

Spilled rinse-aid Always wipe up rinse-aid spills immediately.

Hard water minerals

The affected items arenot corrosion resistant.

The lid of the softeris loose

A sp ay arm is

knocking againstan item in a basket

r

Items of crockeryare loose in thewash cabinet

This may be caused

by on-site installationor the cross-section ofthe piping.

A program was notrun after dishwashersalt was added.

Traces of salt havegotten into the wash cycle.

To clean the interior, use a damp sponge withdishwasher detergent and wear rubber gloves.Never use any other cleaner than dishwasher

detergent for the risk of foaming or suds.

Always run the quick wash program .

without any crockery in the dishwasher andwithout selecting the Turbo function (if present),after adding dishwasher salt.

Check the lip .Ensure the fix is fine.

Interrupt the program, and rearrange the items

which are obstructing the sp ay arm.r

Interrupt the program,

and rearrange the items of crockery.

This has no influence on the dishwasher function.if in doubt, contact a suitably qualified plumber.

Detergent with

colourant was used

Make sure that the detergent is the one without

colourant.

Improper detergent

Make sure the dishwasher is turned on and the door isclosed securely.

Check that the water supply is connected properly and

the water is turned on.

Make sure to close the door properly and latch it.

Make sure the power cord is properly plugged into thewall socket.

Power supply is not

turned on

Water pressure is low

Door of dishwashernot properly closed.

Kink in drain hose

Filter clogged

Kitchen sink clogged

Check drain hose.

Check coarse the filter

(see section titled )" Cleaning The Filter "

Check the kitchen sink to make sure it is draining well.If the problem is the kitchen sink not draining ,you may

need a plumber rather than a serviceman for dishwashers.

Use only the special dishwasher detergent to avoid suds.

If this occurs, open the dishwasher and let suds evaporate.Add 1 gallon of cold water to the tub. Close and latch thedishwasher, then select any cycle. Dishwasher will drain

out the water at the first step.Open the door after drainingis stop and check if the suds is disappeared.

Repeat if necessary.

The dishes were not

loaded correctly.

See notes in " Loading the Dishwasher Baskets ".

Select a more intensive program.

See" Wash Cycle Table ."

Use more detergent, or change your detergent.

Rearrange the items so that the sp ay can rotate freely.r

Clean and/or fit the filter combination correctly.

Clean the sp ay arm jets. See "Cleaning the SprayArms".

r

Use less detergent if you have soft water and selecta shortest cycle to wash the glassware and to get

them clean.

Use a mild abrasive cleaner to eliminate those marks.

Re-loading the dishes properly.

Load the dishwasher as suggested in the directions.

Increase the amount of rinse-aid/refill the rinse-aiddispenser.

Do not empty your dishwasher immediately afterwashing. Open the door slightly so that the steam can

escape. Begin unloading the dishwasher only once the dishes are barely warm to the touch. Empty the low

basket first. This prevents water form dropping offdishes in the upper basket.

In short program the washing temperature is lower.

This also lowers cleaning performance. Choosea program with a long washing time.

Water drainage is more difficult with these items.

Cutlery or dishes of this type are not suitable forwashing in the dishwasher.

The program was

not powerful enough.

Not enough detergentwas dispensed.

Items are blockingthe path of sp ay arms.r

The filter combinationin the base of washcabinet is not clean oris not correctly fitted.This may causethe sp ay arm jetsto get blocked.

r

Combination of softwater and too muchdetergent.

Aluminum utensilshave rubbed againstdishes.

Dishes blockdetergent cups.

Improper loading

Too little rinse-aid

Dishes are removedtoo soon

Wrong programhas been selected

Use of cutlery witha low-quality coating

If overflow occurs, turn off the main water supply before calling a service.If there is water in the base pan because of an overfill or small leak,the water should be removed before restarting the dishwasher.

Overflow.

When some malfunctions come on, the appliance will display error codes to warn you:

Longer inlet time.Faucets is not opened, or water intake isrestricted,or water pressure is too low.

Some element of dishwasher leaks .E4

E1

E8 Divider vale failed Divider vale failed

Height : 845mm

Width : 598mm

Depth : 610mm( )with the door closed

Water pressure: 0.04-1.0MPaPower supply: see rating label

Capacity: 14 place settings

Position one: lift the left basket up, both left and rightbaskets are sideling.

Position two: adjust the left basket to lower position, leftbasket is flat and right basket is sideling.

Position three: lift the right basket up, both left and rightbaskets are flat.

Position Four: Move the right basket from right to left, twobasket are overlapping.

Position Five: Remove the right basket from the tray,only has the left basket.

Mode 1

Mode 2

Mode 3

Mode 4

Mode 5

Cutlery basket could be have 5 positions:

E-WASTE MANAGEMENT GUIDELINES

Under the E-Waste (Management & Handling) Rules, 2011 (hereafter referred to as the “E-Waste Rules”), it is

electrical and electronic equipment through authorized recyclers.

E-Waste has been defined as “waste electrical and electronic equipment, whole or in part or rejects from their

manufacturing and repair process, which are intended to be discarded”.

E-Waste contains various hazardous materials like lead, mercury, cadmium, hexavalent chromium, polybrominated

biphenyls and polybrominateddiphenyls ethers. Hence, improper handling and disposal of e-waste releases these

hazardous material in the environment causing pollution, contamination of soil and water and various health hazards.

Though the product purchased by you does not contain any hazardous material above the prescribed limit under the E-

Waste Rules, it is imperative that the product should be handled with utmost caution and as per the guidelines

mentioned in this manual including the following Do's and Don'ts –

We have tied up with government approved e-waste recycler for facilitating the collection of e-waste from our channel

partners and customers for recycling. You are simply required to call our toll free number 1800 30 00 00 11 and register

your request for collection of e-waste. Once your request is received, the representatives of the authorized recycler

would collect the e-waste from your house/premises after paying the value of the same to you. For more details and

information on our E-Waste Recycling Program kindly visit our website www.carriermidea.com.

The following marking/symbol on the product or carton indicates that the product and its accessories/parts (e.g. remote

controller, batteries, spare parts etc.) should not be disposed of with other household waste at the end of their working

life. Please separate these items from other types of waste and recycle them responsibly for conservation of the

environment and collective well-being.

Do's Dont'sHand over the E-Waste to the Company / Authorised

recycler.

Never sell the e-waste to any unauthorized agencies,

scrap dealer/kabadiwalahs.

E-Waste should never be thrown in household bins. Never throw E-Waste in bins as part of

household waste.

Keep the product in isolated area, after it becomes

non-functional/un-repairable so as to prevent its

accidental breakage.

Never keep E-Waste in open and exposed area,

accessible by all.

The product should not be opened by the User himself/

herself, but only by authorised service personnel.

Never open/dismantle any e-waste on your own.

E-WASTE RECYCLING PROGRAM

PROPER HANDLING AND/OR RECYCLING OF THE DISH WASHER

incumbent for all consumers, including the purchaser of this dish washer, to properly recycle and dispose of all

Product Warranty Terms & Conditions (Dishwasher)

CARRIER MIDEA INDIA PRIVATE LIMITED (hereinafter referred to as the "Company"), hereby warrants to the original domestic purchaser (here in after called the "Purchaser") of the product (as detailed within the Warranty Registration Card and here in after referred to as the "said unit") that the said unit is free from defects in materials and workmanship under normal use and service and under specified voltage conditions, and that during a period of twenty four (24) months commencing from the date of invoice, as provided in the Warranty Registration Card, the Company undertakes to repair or to replace as it deems fit in sole discretion, free of charge, any part or parts of the said unit (including accessories) which proves to be defective in materials or workmanship.

CONDITIONS OF WARRANTY

1. The warranty shall be valid and that the Purchaser can have the benefit of this warranty, if and only if the Purchaser has duly intimated the fault to the Company or its authorized dealer and that the unit is in the possession of and is used by the Purchaser.

2. The Warranty will shall be valid only for the said period as specified above, irrespective of whether the said unit has been in use or not for any reason whatsoever, or the unit is moved from one location to another. The warranty period specified above shall include time taken for repairs, replacements, testing of unit, technical breakdowns, transit time etc. This warranty shall automatically expire by efflux of time on completion of the period indicated herein above and no notice of such expiry will be given by the Company.

3. This warranty shall stand automatically terminated in the event of the said unit being serviced, repaired, installed, de-installed, re-installed or otherwise attended to by and person or organization or agency or by the Purchaser himself (by whatever name called), other that the authorized representative / Dealer of the Company.

4. Parts of the units replaced or repaired under the terms of this warranty are warranted only for the remaining period of the original warranty period.

5. For attending any service call under this warranty beyond the Municipal limits of the locality in which the authorized representative/dealer is situated (outstation locations), all to and fro traveling and other incidental expenses as prevailing from time to time incurred in connection with the visit of the service personnel, technicians etc., shall be borne by the Purchaser and shall be payable in advance. Additionally, all expenses incurred by the authorized representative/dealer in collecting the unit or any part thereof from such outstation locations and its return to the original location shall be borne exclusively by the Purchaser.

6. Any damage/fault caused due to sabotage, improper handling or treatment, carelessness, accident, fire, flood, earthquake or any act of God, or any corrosive action on the original fittings, valves etc. for whatever reason, shall not be covered under this warranty.

7. While the Authorized Dealers/Company will make every effort to carry out repairs/replacement of parts under this warranty as soon as the complaint is received, it is expressly made clear that the Authorized Dealer/Company shall not be liable to do so within any specified period of time.

8. It shall be absolute discretion of the Company to (a) effect the repairs or replacement of parts whether at the site of installation or at any service center; and (b) have the job attended to either by the Company's service personnel or of its authorized dealers. (c) This warranty shall be strictly limited to the repairs or replacement of defective parts specified in the warranty. This warranty shall not cover any consequential of resulting liability. (d) This warranty shall not, in any case, extend towards payments of an monetary consideration whatsoever of replacement or return of the product. (e) The company may repair/ supply parts free of cost during the warranty period. This warranty does not cover any Excise Duty, Central or Sales Tax, Octroi and other local taxes or levies on the components/parts. (f) The parts shall be replaced by functionally operating equivalent material only and not necessarily brand new ones and are to be different from the one originally fitted. The parts thus removed shall be taken back by the company. (g) The company reserves the right to retain any part or components replaced at its sole discretion during the warranty period.

9. This warranty is in the nature of and for the purposes as set forth herein above and in particular, the Company shall not in any event be liable for any direct, indirect, incidental or consequential loss or damages to either the said purchaser and/or his property or any other third party in course of attending to any complaint.

10. Limitation of Warranty: Company shall not be responsible for providing any warranty under the following situations:

i. If the appliance is not used in accordance with manufacturer’s instruction given in the “User’s Manual”. ii. Service engineers visits to place of product installation to teach/instruct on how to use the product.

iii. Noise or vibration that is considered normal for product operations like warning beeps, water shower sound, utensil sound etc.

iv. Correcting the installation, for example leveling the product, adjustment of inlet tap/drain hose etc v. Normal maintenance which is recommended by the user’s manual vi. Removal of foreign objects / substances from the machine, including the pump and inlet hose filter for

example grit, food wastage, utensils etc. vii. Replace fuses in or correct house wiring or correct house plumbing viii. If the product is used for commercial purpose, it is not warranted (example : Public places such as

restaurants, lodging house, dormitory etc) ix. Any damage caused by accident, mishandling, tampering with installation, or negligent in following

instructions of the user manual issued by the Company. If the products has been installed/serviced / repaired/ opened or tampered by any unauthorized personnel.

x. Any damage caused by power surges and dips, improper electrical circuit outside the unit or by any defective electrical supply. If defects arise/caused by accidents, alteration, misuse, substitution of original components with spurious/non-genuine components attacked by household pest/ rodent, fire, flood, earthquake, lighting and/or any other act of God/ natural calamities.

xi. At any time, during the currency of the warranty period, if any part of the unit is tampered with, altered, repaired or serviced by any unauthorized person, not being the authorized representative of the Company or its authorized dealers.

xii. If defects arising with optional accessories like trolleys, machine cover, on-line filter, inlet/ exhaust extension hoses, tap adapter, extended power supply cable, adjustment feet cover, etc. thereof

xiii. The serial number on the unit or any part thereof is damaged, defaced, altered, obliterated, or tampered with or removed for any reason whatsoever.

xiv. If sea water or any substandard detergent/salts has been used in the appliance. xv. The product is shifted outside India. xvi. Damage to the product due to operation in an abnormally corrosive alkaline / acidic atmosphere.

Product/Parts is found defective if the product is installed/operated in abnormally corrosive alkaline / acidic atmosphere or near muddy sewages because toxic gases are harmful for the product.

xvii. This warranty does not cover any type of painting, plating including rusting etc., or defects thereof 11. None of the employees and/or Authorized dealers of the Company have the authority whatsoever to vary the

terms and conditions of this warranty. 12. This warranty shall be deemed to have been issued at Gurgaon in the State of Haryana, and Courts at Gurgaon

shall have exclusive jurisdiction on matters covered by or following from this warranty, and the Purchaser alone shall have cause of action arising out of the transaction.

Customer Name:

Product Name:

Address:

Dealer Name & Address:

Date of Purchase:

Model No :

Signature of the dealer with seal:

Sr. No of the unit :

Invoice No. :

Carrier Midea India Pvt. Ltd.

Customer Name:

Product Name:

Address:

Dealer Name & Address:

Date of Purchase:

Model No :

Signature of the dealer with seal:

Sr. No of the unit :

Invoice No. :

Midea Copy

Customer Copy

Carrier Midea India Pvt. Ltd.