Dfu Sr7500 Final Eng
Transcript of Dfu Sr7500 Final Eng
-
8/3/2019 Dfu Sr7500 Final Eng
1/56
Model SR7500/SR8500 User Guide
AV Surround Receiver
-
8/3/2019 Dfu Sr7500 Final Eng
2/56
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle isintended to alert the user to the presence of uninsulated dangerous voltagewithin the products enclosure that may be of sufficient magnitude to constitutea risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the userto the presence of important operating and maintenance (servicing) instructionsin the literature accompanying the product.
WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUGTO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR VITER LES CHOC LECTRIQUES, INTRODUIRE LALAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTEDE LA PRISE ET POUSSER JUSQUAU FOND.
NOTE TO CATV SYSTEM INSTALLER:This reminder is provided to call the CATV (Cable-TV) system installers attention to Section 820-40 of theNEC which provides guidelines for proper grounding and, in particular, specifies that the cable groundshall be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTE:
This equipment has been tested and found tocomply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residentialinstallation. This equipment generates, uses andcan radiate radio frequency energy and, if notinstalled and used in accordance with theinstructions, may cause harmful interference toradio communications. However, there is noguarantee that interference will not occur in aparticular installation. If this equipment does causeharmful interference to radio or te levisionreception, which can be determined by tuning the
equipment off and on, the user is encouraged to tryto correct the interference by one or more of thefollowing measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipmentand receiver.
- Connect the equipment into an outlet on a circuitdifferent from that to which the receiver isconnected.
- Consult the dealer or an experienced radio/TVtechnician for help.
IMPORTANT SAFETYINSTRUCTIONSREAD BEFORE OPERATING EQUIPMENT
This product was designed and manufactured tomeet strict quality and safety standards. There are,however, some installat ion and operat ionprecautions which you should be particularlyaware of.
1. Read Instructions All the safety andoperating instructions should be read beforethe product is operated.
2. Retain Instructions The safety and operatinginstructions should be retained for futurereference.
3. Heed Warnings All warnings on the productand in the operating instructions should beadhered to.
4. Follow Instructions All operating and useinstructions should be followed.
5. Cleaning Unplug this product from the walloutlet before cleaning. Do not use liquidcleaners or aerosol cleaners. Use a dampcloth for cleaning.
6. Attachments Do not use attachments notrecommended by the product manufactureras they may cause hazards.
7. Water and Moisture Do not use this productnear water-for example, near a bath tub, washbowl, kitchen sink, or laundry tub, in a wetbasement, or near a swimming pool, and thelike.
8. Accessories Do not place this product on anunstable cart, stand, tripod, bracket, or table.The product may fall, causing serious injury toa child or adult, and serious damage to theproduct. Use only with a cart, stand, tripod,bracket, or table recommended by themanufacturer, or sold with the product. Anymounting of the product should follow themanufacturers instructions, and should use amounting accessory recommended by themanufacturer.
9. A product and cart combination should bemoved with care. Quick stops, excessiveforce, and uneven surfaces may cause theproduct and cart combination to overturn.
10. Ventilation Slots and openings in the cabinetare provided for ventilation and to ensurereliable operation of the product and to protectit from overheating, and these openings mustnot be blocked or covered. The openingsshould never be blocked by placing theproduct on a bed, sofa, rug, or other s imilarsurface. This product should not be placed ina built-in installation such as a bookcase or
rack unless proper ventilation is provided orthe manufacturers instructions have beenadhered to.
11. Power Sources This product should beoperated only from the type of power sourceindicated on the marking label. If you are notsure of the type of power supply to your home,consult your product dealer or local powercompany. For products intended to operatefrom battery power, or other sources, refer tothe operating instructions.
-
8/3/2019 Dfu Sr7500 Final Eng
3/56
12. Grounding or Polarization This product maybe equipped with a polarized alternating-
current line plug (a plug having one blade
wider than the other). This plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized
plug.
AC POLARIZED PLUG
13. Power-Cord Protection Power-supply cordsshould be routed so that they are not likely to
be walked on or pinched by items placed upon
or against them, paying particular attention to
cords at plugs, convenience receptacles, and
the point where they exit from the product.
14. Protective Attachment Plug The product isequipped with an attachment plug having
overload protection. This is a safety feature.See Instruction Manual for replacement or
resetting of protective device. If replacement
of the plug is required, be sure the service
technician has used a replacement plug
specified by the manufacturer that has the
same overload protection as the original plug.
15. Outdoor Antenna Grounding If an outsideantenna or cable system is connected to the
product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static
charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mastand supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna-
discharge unit, connection to grounding
electrodes, and requirements for the
grounding electrode. See Figure 1.
16. L ightning For added protection for thisproduct during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
17. Power L ines An outside antenna systemshould not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might be
fatal.
18. Overloading Do not overload wall outlets,extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
19. Object and Liquid Entry Never push objectsof any kind into this product through openings
as they may touch dangerous voltage points
or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind onthe product.
20 . Servicing Do not attempt to service thisproduct yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualified service personnel.
21. Damage Requiring Service Unplug thisproduct from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to its normal operation.
e. If the product has been dropped or damaged
in any way, and
f. When the product exhibits a distinct change inperformance this indicates a need forservice.
22. Replacement Parts When replacementparts are required, be sure the service
technician has used replacement parts
specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
23. Safety Check Upon completion of anyservice or repairs to this product, ask the
service technician to perform safety checks to
determine that the product is in proper
operating condition.
24. Wall or Ceiling Mounting The product shouldbe mounted to a wall or ceiling only as
recommended by the manufacturer.
25. Heat The product should be situated awayfrom heatsources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
FIGURE 1
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numrique de la Classe B est conforme la norme NMB-003 du Canada.
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPSPOWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
-
8/3/2019 Dfu Sr7500 Final Eng
4/56
1
ENGLISHTABLE OF CONTENTS INTRODUCTION
Thank you for purchasing the Marantz SR7500Surround receiver.This remarkable component has been engineeredto provide you with many years of home theaterenjoyment. Please take a few minutes to read thismanual thoroughly before you connect andoperate the SR7500.As there are a number of connection andconfiguration options, you are encouraged to
discuss your own particular home theater setupwith your Marantz A/V specialist dealer.
This user guide covers the SR7500 andSR8500, though the SR7500 is given for thetitle. Explanations of features belongingonly to the SR8500 are indicated asSR8500 only.
PRECAUTIONSCAUTIONS ON INSTALLATION
For heat dispersal, leave at least 20 cm/8 inch ofspace between the top, back and sides of this unit
and the wall or other components. Do not obstruct the ventilation holes.
INTRODUCTION.................................. 1
PRECAUTIONS ................................... 1
DESCRIPTION..................................... 2
FEATURES ..........................................4
ACCESSORIES ................................... 4
FRONT PANEL .................................... 5FL DISPLAY AND INDICATER ........................................6
REAR PANEL ......................................7
REMOTE CONTROLLER RC8500SR. 8NAMES AND FUNCTIONS.............................................. 8
LCD INDICATORS...........................................................9
REMOTE CONTROL RANGE ....................................... 10
LOADING BATTERIES.................................................. 10
BATTERY REPLACEMENT INTERVAL ........................ 10
SETTING THE TIME ..................................................... 10
GENERAL INFORMATION OF RC8500SR TO SR7500 ..11
CONNECTIONS................................. 12SPEAKER PLACEMENT............................................... 12
CONNECTING SPEAKERS .......................................... 12
CONNECTING AUDIO COMPONENTS........................ 13
CONNECTING VIDEO COMPONENTS........................ 14ADVANCED CONNECTING.......................................... 15
CONNECTING THE REMOTE CONTROL JACKS .......15
CONNECTING THE ANTENNA TERMINALS ............... 16
CONNECTING FOR THE MULTI ROOM ......................17
SETUP ............................................... 18ON SCREEN DISPLAY MENU SYSTEM ......................18
1 INPUT SETUP
(ASSIGNABLE DIGITAL INPUT) .............................. 19
2 SPEAKER SETUP.....................................................19
3 PREFERENCE ..........................................................22
4 PL II (PRO LOGIC II) MUSIC PARAMETER ............ 22
5 CS II (CIRCLE SURROUND II) PARAMETER ........ 22
6 MULTI ROOM ............................................................ 23
7 7.1 CH INPUT LEVEL................................................23
8 DC TRIGGER SETUP ...............................................23
BASIC OPERATION (PLAY BACK) .. 24SELECTING AN INPUT SOURCE ................................ 24
VIDEO CONVERT ......................................................... 24
SELECTING THE SURROUND MODE ......................... 24
ADJUSTING THE MAIN VOLUME ................................24
ADJUSTING THE TONE (BASS & TREBLE) CONTROL ... 24
TEMPORARILY TURNING OFF THE SOUND.............. 25
USING THE SLEEP TIMER...........................................25
NIGHT MODE ................................................................25
SURROUND MODE........................... 25
OTHER FUNCTION ........................... 29TV AUTO ON/OFF FUNCTION ..................................... 29
ATTENUATION TO ANALOG INPUT SIGNAL ..............29
LISTENING THROUGH HEADPHONES ...................... 29
DOLBY HEADPHONE MODE ....................................... 29
VIDEO ON/OFF .............................................................29
DISPLAY MODE ............................................................29
SELECTING ANALOG AUDIO INPUT ORDIGITAL AUDIO INPUT............................................. 30
RECORDING AN ANALOG SOURCE ........................... 30
SPEAKER A/B ...............................................................30
7.1 CH INPUT ................................................................30
AUX2 INPUT.................................................................. 31
LIP.SYNC.......................................................................31
BASIC OPERATION (TUNER) .......... 32LISTENING TO THE TUNER ........................................32
PRESET MEMORY ....................................................... 33
MULTI ROOM SYSTEM..................... 35MULTI ROOM PLAYBACK USING
THE MULTI ROOM OUT TERMINALS .....................35
MULTI ROOM PLAYBACK USING
THE MULTI SPEAKER TERMINALS ........................ 35OPERATION OF THE MULTI ROOM OUTPUTS WITH THE
REMOTE CONTROL FROM A SECOND ROOM ........35
REMOTE CONTROLLER OPERATION ... 36CONTROLLING MARANTZ COMPONENTS................ 36
BASIC OPERATION ...................................................... 38
PROGRAMMING MACROS ..........................................41
CLONE MODE ...............................................................43
SETUP........................................................................... 44
TROUBLESHOOTING ....................... 45
TECHNICAL SPECIFICATIONS ....... 46
DIMENSIONS .................................... 46
20 cm (8 ins.)
20 cm (8 ins.)
AV S URROUND RE CE I V E RS R5500
ENTER
-
8/3/2019 Dfu Sr7500 Final Eng
5/56
2
EN
GLISH
THX need not be activated for music, movies madeespecially for TV, or shows such as sportsprogramming, talk shows, etc.This is because they were originally mixed for asmall room environment.
THX is a trademark or registered trademark of THXLtd. Surround EX is a jointly developed technologyof THX and Dolby Laboratories, Inc. and is atrademark of Dolby Laboratories, Inc. Used underauthorization. All rights reserved.
THX Surround EXDolby DIgital Surround EX is ajoint development of Dolby Laboratories and THXLtd.
In a movie theater, film soundtracks that have beenencoded wi th Dolby Digi tal Surround EXtechnology are able to reproduce an extra channelwhich has been added during the mixing of theprogram. This channel, called Surround Back,places sounds behind the listener in addition to thecurrently available front left, front center, frontright, surround right, surround left and subwooferchannels. This additional channel provides theopportunity for more detailed imaging behind the
l istener and brings more depth, spaciousambience and sound localization than ever before.Movies that were created using the Dolby DigitalSurround EX technology, when released into thehome consumer market may exhibit wording to thateffect on the packaging. A list of movies createdusing this technology can be found on the Dolbyweb site at www.dolby.com. A list of availableDVD software titles encoded with this technologyan be found at www.thx.com.Only receiver and controller products bearing theTHX Surround EX logo, when in the THX SurroundEX mode, faithfully reproduce this new technologyin the home. This product may also engage theTHX Surround EX mode during the playback of 5.1channel material that is not Dolby Digital SurroundEX eocnded. In such case, the information
delivered to the Surround Back channel will beprogram dependent and may or may not be verypleasing depending on the particular soundtrackand the tastes of the individual listener.
SURROUND EX is a trademark of DolbyLaboratories. Used under authorization.
DTS was introduced in 1994 to provide 5.1channels of discrete digital audio into home theatersystems.DTS brings you premium qual i ty discretemultichannel digital sound to both movies andmusic.DTS is a multichannel sound system designed tocreate full range digital sound reproduction.The no compromise DTS digital process sets thestandard of quality for cinema sound by deliveringan exact copy of the studio master recordings toneighborhood and home theaters.Now, every moviegoer can hear the sound exactlyas the moviemaker intended.DTS can be enjoyed in the home for either moviesor music on of DVDs, LDs, and CDs.
DTS and DTS Digital Surround are registeredtrademarks of Digital Theater Systems, Inc.
The advantages of discrete multichannel systems
over matrix are well known.But even in homes equipped for discretemultichannel, there remains a need for high-qualitymatrix decoding. This is because of the largelibrary of matrix surround motion pictures availableon disc and on VHS tape; and analog televisionbroadcasts.The typical matrix decoder of today derives acenter channel and a mono surround channel fromtwo-channel matrix stereo material. It is better thana simple matrix in that it includes steering logic toimprove separation, but because of its mono,band-limited surround it can be disappointing tousers accustomed to discrete multichannel.
Neo:6 offers several important improvements as
follow, Neo:6 provides up to six full-band channels ofmatrix decoding from stereo matrix material.Users with 6.1 and 5.1 systems will derive sixand five separate channels, respectively,corresponding to the standard home-theaterspeaker layouts.
Neo:6 technology al lows various soundelements within a channel or channels to besteered separately, and in a way which followsnaturally from the original presentation.
DESCRIPTION
TH X is an exclusive set of standards andtechnologies established by the world-renownedfilm production company, Lucasfilm Ltd. THXresulted from George Lucas desire to reproducethe movie soundtrack as faithfully as possible both
in the movie theater and in the home theater.THX engineers developed patented technologiesto accurately translate the sound from a movietheater environment into the home, correcting thetonal and spatial errors that occur.When the THX mode of the SR7500 is on, threedistinct THX technologies are automaticallyadded:Re-Equalization-restores the correct tonal balancefor watching a movie in a home environment.These sounds are otherwise mixed to be brighterfor a large movie theater. Re-EQ compensates forthis and prevents the soundtracks from beingoverly bright and harsh when played in a hometheater.Timbre Matching-filters the information going to
the surround speakers so they more closely matchthe tonal characteristics of the sound coming fromthe front speakers.This ensures seamless panning between the frontand surround speakers.Adaptive Decorrelation-slightly changes onesurround channels time and phase relationshipwith respect to the other surround channel.This expands the listening position and createswith only two surround speakers the samespacious surround experience as in a movietheater with multiple surround speakers.The Marantz SR7500 was required to pass arigorous series of quality and performance tests, inaddi t ion to incorporat ing the technologiesexplained above, in order to be THX certified byLucasfilm Ltd.THX requirements cover every aspect ofperformance including pre-amplifier and powerampl i f ier performance and operat ion, andhundreds of other parameters in both the digitaland analog domain.Movies which have been encoded in Dolby Digital,DTS, Dolby Pro Logic, stereo and Mono will allbenefit from the THX mode when being viewed.The THX mode should only be activated whenwatching movies which were originally producedfor a movie theater environment.
Neo:6 offers a music mode to expand stereononmatrix recordings into the five- or six-channel layout, in a way which does not diminishthe subtlety and integrity of the original stereorecording.
DTS-ES Extended Surround is a new multichanneldigital signal format developed by Digital TheaterSystems Inc. While offering high compatibility with
the conventional DTS Digital Surround format,DTS-ES Extended Surround greatly improves the360-degree surround impression and spaceexpression thanks to further expanded surroundsignals. This format has been used professionallyin movie theaters since 1999.In addition to the 5.1 surround channels (FL, FR,C, SL, SR and LFE), DTS-ES Extended Surroundalso offers the SB (Surround Back) channel forsurround playback with a total of 6.1 channels.DTS-ES Extended Surround includes two signalformats with different surround signal recordingmethods, as DTS-ES Discrete 6.1 and DTS-ESMatrix 6.1.
DTS , DTS-ES and Neo:6 are trademarks of
Digital Theater Systems, Inc.
The stereo CD is a 16-bit medium with sampling at44.1 kHz. Professional audio has been 20- or 24-bit for some time, and there is increasing interest inhigher sampling rates both for recording and fordelivery into the home. Greater bit depths provideextended dynamic range. Higher sampling ratesallow wider frequency response and the use ofanti-alias and reconstruction filters with morefavorable aural characteristics.
DTS 96/24 allows for 5.1channel sound tracks to
be encoded at a rate of 96kHz/24bits on DVD-Video titles.When DVD-video appeared, it became possible todeliver 24-bit, 96 kHz audio into the home, but onlyin two channels, and with serious limitations onpicture. This capability has had little use.DVD-audio allows 96/24 in six channels, but a newplayer is needed, and only analog outputs areprovided, necessitating the use of the D/Aconverters and analog electronics provided in theplayer.
-
8/3/2019 Dfu Sr7500 Final Eng
6/56
3
ENGLISH
DTS 96/24 offers the following:1. Sound quality transparent to the original 96/24
master.
2. Full backward compatibility with all existingdecoders. (Existing decoders will output a 48kHz signal)
3. No new player required: DTS 96/24 can becarried on DVD-video, or in the video zone ofDVD-audio, accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality full-motion video, for music programs and motionpicture soundtracks on DVD-video.
DTS and DTS 96/24 are trademarks of DigitalTheater Systems, Inc.
Dolby Digital identifies the use of Dolby Digitalaudio coding for such consumer formats as DVDand DTV. As with film sound, Dolby Digital canprovide up to five full-range channels for left,center, and right screen channels, independent leftand right surround channels, and a sixth (.1)channel for low-frequency effects.
Dolby Surround Pro Logic II is an improved matrixdecoding technology that provides better spatialityand directionality on Dolby Surround programmaterial; provides a convincing three-dimensionalsoundfield on conventional stereo musicrecordings; and is ideally suited to bring thesurround experience to automotive sound. Whileconventional surround programming is fullycompatible with Dolby Surround Pro Logic IIdecoders, soundtracks will be able to be encodedspecifically to take full advantage of Pro Logic IIplayback, including separate left and rightsurround channels. (Such material is alsocompatible with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output
channels from 5.1-channel sources. This is doneusing a matrix decoder that derives three surroundchannels from the two in the original recording.For best results, Dolby Digital EX should be usedwith movies soundtracks recorded with DolbyDigital Surround EX.
About Dolby Pro LogicIIxDolby Pro Logic IIx technology delivers a naturaland immersing 7.1-channel listening experience tothe home theater environment. A product ofDolby's expertise in surround sound and matrixdecoding technologies, Dolby Pro Logic IIx is acomplete surround sound solution that maximizesthe entertainment experience from stereo as wellas 5.1-channel encoded sources.
Dolby Pro Logic IIx is fully compatible with DolbySurround Pro Logic technology and can optimallydecode the thousands of commercially available
Dolby Surround encoded video cassettes andtelevision programs with enhanced depth andspatiality. It can also process any high-qualitystereo or Advanced Resolution 5.1-channel musiccontent into a seamless 6.1- or 7.1-channellistening experience.
The Dolby Headphone technology provides asurround sound listening experience over headphones.When listening to multichannel content such asDVD movies over headphones, the l istening
experience is fundamentally different thanlistening to speakers. Since the headphonespeaker drivers are covering the pinna of the ear,the l istening experience differs greatly fromtraditional speaker playback. Dolby uti l izespatented headphone perspective curves to solvethis problem and provides a non-fatiguing,immersive, home theater listening experience.Dolby Headphone also delivers exceptional 3Daudio from stereo material.
Ma n u fa c tu r e d u n d e r l i c e n s e f r o m D o l b yLaboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
Circle Surround II (CS- II) is a powerful andversati le mult ichannel technology. CS- II isdesigned to enable up to 6.1 multichannel surroundsound playback from mono, stereo, CS encodedsources and other matrix encoded sources. In allcases the decoder extends it into 6 channels ofsurround audio and a LFE/subwoofer signal. TheCS-II decoder creates a listening environment thatplaces the listener inside music performancesand dramatical ly improves both hi- f i audioconventional surround-encoded video material.CS- II provides composite stereo rear channels togreatly improve separation and image positioningadding a heightened sense of realism to both audioand A/V productions.CS-II is packed with other useful feature like dialogclarity (SRS Dialog) for movies and cinema-likebass enrichment (TruBass). CS-II can enable thedialog to become clearer and more discernable inmovies and it enables the bass frequenciescontained in the original programming to moreclosely achieve low frequenciesovercoming thelow frequency limitations of the speakers by fulloctave.
Circle Surround II, Dialog Clarity, TruBass, SRS
and symbol are trademarks of SRS Labs, Inc.Circle Surround II, Dialog Clarity and TruBasstechnology are incorporated under license fromSRS Labs, Inc.
(SR8500 only)
HDCD (High Definition Compatible Digital ) is apatented process for delivering on Compact Discthe full richness and details of the originalmicrophone feed.HDCD encoded CDs sound better because theyare encoded wi th 20-bi ts of real musicalinformation as compared to 16-bits for all other
CDs.HDCD overcomes the limitation of the 16-bit CDformat by using a sophisticated system to encodethe additional four bits onto the CD while remainingcompletely compatible with the CD format.When listening to HDCD recordings, you hearmore dynamic range, a focused 3-D sound stage,and extremely natural vocal and musical timbre.With HDCD, you get the body, depth and emotionof the original performance not a flat, digitalimitation.
HDCD system manufactured under license fromMicrosoft. This product is covered by one or moreof the following: In the United States 5,479,1685,638,074 5,640,161 5,808,574 5,838,2745,854,600 5,864,311 5,872,531 and in Australia669,114 with other patents pending.
-
8/3/2019 Dfu Sr7500 Final Eng
7/56
4
EN
GLISH
ACCESSORIESRemote Controller RC8500SR
2 31
5 64
8
0
97
MEMOCLEAR
DSS
AMPAUX2AUX1TAPE
TUNER CD CD-R MD
VCRDVDTV
SOURCE
OFF ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOLCH
PREV MUTE
MENU EXIT
GUIDE
T E S T C H . SE L
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
1 2
LIGHT
Learning Remote ControllerRC8500SR
Microphone MC-10
AC cable
AAA-size batteries 3
AM Loop Antenna
FEATURESThe SR7500 incorporates the latest generation ofdigital surround sound decoding technology suchas Dolby Digital EX, Dolby Digital, DTS ES(Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema,Music), Dolby Pro-Logic II (Movie, Music andGame), Dolby Pro-Logic IIx (Movie, Music andGame), Circle Surround II (Cinema, Music andMono).In addition, Marantz has focused on the future. Byutilizing pre-out jacks, 7.1 direct inputs and a RS-232Ccommunication port, the SR7500 is tomorrowstechnology, today!
THX Select certified7ch amplifiers have enough power for even themost difficult conditions found in large rooms.Enormous power reserves endow the system withsubstantial dynamic ability at high sound levels.105 watts (SR7500) / 110 watts (SR8500) to eachof the 7 main channels the power amp sectionfeatures an advanced, premium high-storagepower supply capacitors, and fully discrete outputstages housed in cast aluminum heat sinks .
The SR7500 incorporates the most advancedDigital Signal Processing circuitry, along with aCrystal 192 kHz/24 bit D/A converter in each ofthe 7 channels. Independent power supply circuitsare incorporated for the FL display, audio andvideo sections for maximum separation, clarityand dynamic range. Together with hand-selectedcustomized components, all elements work inharmony to recreate the emotion, exactly as theartist had intended.
The SR7500 is designed and engineered withextensive feedback from custom installationexperts, dealers and consumers. It features multi-room/multisource, assignable DC trigger, a RS-232C communication port, Flasher input, heavyduty speaker binding posts and an extensive arrayof both analog and digital inputs / outputs. With 6
assignable digital inputs (7 total), 4 componentinputs, SACD Multi Channel (7.1 channel) directinputs video convert system and a speaker-B andOSD output versatility is taken to a stunning newlevel. Furthermore, the SR7500 can output theOSD information through the Y/C (S-video) andcomposite video outputs.
An easy-to-use programmable, learning remotecontrol allows full access to all of the operatingfunctions and can be used for system operation aswell.
The new generation of Marantz Receivers is stylishand completely symmetrical. On the front panel ofthe SR7500, buttons are kept to a minimum. Sourceselectors and volume controls are intuitively placed.The SR7500 is here to perform in your unrivaledhome entertainment setup.
THX / THX Surround EX Dolby Digital EX, Dolby Digital, DTS ES
(Discrete 6.1, Matrix 6.1, Neo:6) Dolby Pro Logic II (Movie, Music, Game) Dolby Pro Logic IIx (Movie, Music, Game) Circle Surround II (Cinema, Music, Mono)
MRAC (Marantz Room Acoustic Calibration) 7 105 Watts (8 Ohms), Discrete Amplifiers
(SR8500: 7 110 Watts) High Power Current Feedback Circuitry Massive Energy Power Supply, Huge EI
Transformer, Large ELCOs. 192 kHz/24 bit Crystal DAC for all 8 Channels 32 bit Digital Surround Processing Chipsets Video Off Mode Large Heavy Duty Speaker Terminals for all
Channels RS-232C Terminal for Future Upgrade or
System Control Set Up Menu via all Video Output
(Composite, S-Video and Component video) Auto Input Signal Detection
Improved Station Name Input Method, 50Presets Auto Adjust Function for Speaker Distance
Settings (Delay Time) Front Optical AUX Input
(Digital Camera, Portable DVD) Assignable DC Trigger Output Programmable, learning remote control Flasher Input Video convert system (Composite Video
S Video Component Video) Assignable DVI-D INPUT (SR8500 only) HDCD (SR8500 only) Copper Plate Chassis (SR8500 only) Troidal Core Transformer (SR8500 only)
FM Antenna
Front AUX Jack Cover
PUSHPUSH
User Guide
-
8/3/2019 Dfu Sr7500 Final Eng
8/56
5
ENGLISH
Notes: When using headphones, the surround mode will
change to STEREO and Dolby Headphone byMENU and Cursor button.
The surround mode returns to the previous settingas soon as the headphone plug is removed fr omthe jack.
r SURROUND MODE buttonYou can select the surround mode by pressing thisbutton.
t AUTO (Auto surround) buttonPress this button to select the AUTO mode fromthe surround modes. When this mode is selected,the receiver determines the surround modecorrespond ing to a d ig i ta l i npu t s igna lautomatically.
y MULTI (Multi Room) buttonPress this button to activate the Multiroom system.MULTI indicator will be illuminated in the display.
q POWER switch and STANDBY indicatorWhen this switch is pressed once, the unit turns ONand the display illuminates. When pressed again,the unit turns OFF and t he STANDBY indicator willbe illuminated.
w INPUT SELECTOR knob (AUDIO/ VIDEO)This knob is used to select the input sources.The video function selectors, such as TV, DVD,VCR1, DSS and AUX1 select video and audiosimultaneously.Audio function sources such as CD, TAPE, CD-R/MD, TUNER and AUX2 may be selected inconjunction with a Video source.This feature (Sound Injection) combines a soundfrom one source with a picture from another.Choose the video source first, and then choose adifferent audio source to activate this function.
e HEADPHONE jack for stereo headphonesThis jack may be used to listen to the SR7500 soutput through a pair of headphones. Be certainthat the headphones have a standard 1/4 stereophono plug. Note that the main room speakers willautomatically be turned off when the headphone
jack is in use.
u MULTI SPEAKER buttonPress this button to activate the Multiroom Speakersystem. MULTI indicator will be illuminated in thedisplay. (See page 35)
i BAND buttonPress this button to switch between FM and AM inthe TUNER mode.
o T-MODE buttonPress this button to select the auto stereo mode or
mono mode when the FM band is selected.The AUTO indicator lights in the auto stereomode. (See page 32)
!0 MEMORY buttonPress this button to enter the tuner preset memorynumbers or station names. (See page 33)
!1 CLEAR buttonPress this button to cancel the station-memorysetting mode or preset scan tuning. (See page 33)
!2 INFRARED receiving sensor windowThis window receives infrared signals for the
remote control.
!3 VOLUME control knobAdjusts the overall sound level. Turning the controlclockwise increases the sound level.
!4 AUX1 INPUT jacksThese auxiliary video/audio input jacks accept theconnections of a camcorder, portable DVD, gameetc. When not using these jacks, protect with theincluded jack covers.
How to Attach the Front AUX Jack Cover
AUX1INPUT
AUDIO
S-VIDEO
DIGITAL
VIDEO
L
R
UP
PUSHPUSH
!5 PURE DIRECT buttonWhen this button is pressed, the tone controlcircuitry is bypassed as well as Bass Management.PURE DIRECT indicator will be illuminated in thedisplay.
Notes:
The surround mode is automatically switched toAUTO when the pure direct function is turned on.
Additionally, Speaker Configurations are fixedautomatically as follows.Front SPKR = Large, Center SPKR = Large,Surround SPKR = Large, Sub woofer = On
!6 THX buttonPress this button to select THX processing forinput source.
!7 7.1CH INPUT buttonPress this button to select the output of an externalmultichannel player.
!8 MENU buttonThis button is used to enter the SETUP MAINMENU.
!9 Cursor ( , , , ) / ENTER buttonUse these buttons when operating the SETUPMAIN MENU and TUNER function.
@0 EXIT buttonThis button is used to exit from the SETUP MAINMENU.
@1 DISPLAY buttonWhen this button is pressed, the FL display modeis changed as Surround Mode Auto-display Off Display Off Input Function and the display offindicator (DISP) lights up in condition of DISPLAYOFF.
@2 MRAC button / MIC jackPress to au tomat i ca l l y measure speakercharacteristics using the included microphone(MC-10). (See page 21)
FRONT PANEL
AV SURROUND RECEIVER SR7500
P OW ER O N/ ST AN DB Y P HO NE S
STANDBY
L C R
SL S S R
LFE
DIGITAL
SURROUNDDISP M U LT I A UT O T UN E D S T S P K R A B V - OF F
NIGHT
P EA K A NA LO G
DIGITAL
ATT
S LE EP S UR R D IR EC TAUTO DISC 6.1 MTX 6.1
PCMAAC
AUX1INPUT
AUDIOS-VIDEODIGITAL VIDEO L R
DOWN UP
VOLUME
ENTER
INPUT SELECTOR
!8 @0 @2!9
q t yu i o !0 !1r !2 !3 !4ew
!5 !6 !7 @1 @3
Front AUX Jack Cover
-
8/3/2019 Dfu Sr7500 Final Eng
9/56
-
8/3/2019 Dfu Sr7500 Final Eng
10/56
7
ENGLISH
y RS-232CThe RS-232C port is to be used in conjunction withan external controller to control the operation ofthe SR7500 by using an external device.The RS-232C port may also be used in the futureto update the operating software of the SR7500 sothat it will be able to support new digital audioformats and the like as they are introduced.
u Preamp Outputs(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surroundback left) and SBR (surround back right).Use these jacks for connection to external poweramplifiers.
i AC INLETPlug the supplied power cord into this AC INLETand then into the power outlet on the wall.SR7500 can be powered by 120V AC only.
o AC OUTLETSConnect the AC power cables of components such asa DVD and CD player to these outlets. SWITCHEDand UNSWITCHED outlets are provided.The one marked SWITCHED provides power onlywhen the SR7500 is turned on and is useful forcomponents which you use every time you playyour system.The one marked UNSWITCHED is always live aslong as the SR7500 is plugged into a live outlet.A component connected here may be left onpermanently, or may be switched off with via itsown power switch.
Caution:
In order to avoid potential turn-off thumps, anythingplugged into these outlets should be powered upbefore the SR7500 is turned on.
The capacity of this AC outlet is 120W. Do notconnect devices that consume electricity more thanthe capacity of these AC outlets. If the total power
consumption of the connected devices exceeds thecapacity, the protection circuit shuts down thepower supply.
!0 Speaker outputs terminalsSeven terminals are provided for the front (A) left,front (A) right, front (B) left, front (B) right, frontcenter, surround left and surround right speakers.
!1 Speaker outputs terminals (SURROUNDBACK / MULTI SPEAKER / SPEAKER C)
Two terminals are provided for the front left, andright speakers for multi room (2 nd zone) orsurround back.The terminals can be used to connect a third set ofspeakers by setting the SPEAKER C selectorswitch to ON. For connection and use, see page17.
!2 Subwoofer OutputConnect this jack to the line level input of a poweredsubwoofer. If an external subwoofer amplifier is
used, connect this jack to the subwoofer amplifierinput. If you are using two subwoofers, eitherpowered or with a 2 channel subwoofer amplifier,connect a Y connector to the subwoofer output jack and run one cable from it to each subwooferamplifier.
!3 7.1 CHANNEL or AUX2 INPUTBy connecting a DVD Audio player, SACDmultichannel player, or other components that hasa multichannel port, you can playback the audiowith 5.1 channel or 7.1 channel outputs.
!4 DC TRIGGER output terminalConnect a device that needs to be triggered by DCunder certain conditions (screen, power strip,etc)Use the system OSD setup menu to determine theconditions by which these jack will be active.
Note:
This output voltage is for (status) control only, Itis not sufficient for drive capability.
!5 Multiroom Outputs (Audio L&R, Video)These are the audio and video output jacks for theMulti zone (Multi room).Connect these jacks to optional audio poweramplifiers or video display devices to listen andview the source selected by the multiroom systemin a remote room.
!6 MULTI ROOM REMOTE IN/OUT terminalsIN: Connect to a multi-room remote control
device, available from your Marantz dealer.OUT: Connect to the Marantz component
equipped with remote control (RC-5)terminals in Multi zone (Multi room).
REAR PANEL
e COMPONENT VIDEO INPUT/OUTPUTIf your DVD player or other device has componentvideo connectors, be sure to connect them to thesecomponent video connectors on the SR7500. TheSR7500 has 4 component video input connectorsto obtain the color information (Y, CB, CR) directlyfrom the recorded DVD signal or other videocomponent and one component video outputconnector to output it directly into the matrixdecoder of the display device.By sending the pure DVD component video signaldi rect ly, the DVD signal forgoes the extraprocessing that normally would degrade theimage. The result is vastly increased imagequality, with incredibly life like colors and crispdetail.
r FLASHER IN (Flasher input terminal)These terminals are to control the unit from eachzone. Connect the control signal from a Keypad,etc.
t MONITOR OUTThese are monitor outputs and each one includesboth composite video and S-video configurations.When connecting two video monitors or televisions,be aware that the OSD interface can be used withboth MONITOR OUT connections.
q VIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2)These are the video inputs and outputs. There are4 video inputs and 2 video outputs and each oneincludes both composite video and S-videoconfigurations. Connect VCRs, DVD players, andother video components to the video inputs.The 2 video output channels can be used to beconnected to video tape recorders for makingrecordings.
w FM antenna terminal (75 ohms)Connect an external FM antenna with a coaxialcable, or a cable network FM source.
AM antenna and ground terminalsConnect the supplied AM loop antenna. Use theterminals marked AM and GND. The suppliedAM loop antenna will provide good AM reception inmost areas. Position the loop antenna until youhear the best reception.
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTIRC
IN OUTDSS/VCR2IN OUT OUT
VCR1
VCR1
L
SBR
SBL
OUT
PRE
SLL
SRR
DSS/VCR2DVDTV
R
IN
R SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT IN
L SL
SBR
SBLCD
IN OUT SWOUT
CDR/MDTAPE
OUTIN
IN OUT
VIDEO
MONITOR
OUTMULTI VCR1TV
OUT
(AUX2)
MONITOR
D IG IT AL I N D IG IT AL OU T
4
1
OPT.
2
5
3
6
COAX.
R L RR
FRONT A
L L
FM (75)
ANTENNA
G ND A M
COMPONENTVIDEO
CB/PBCR/PR
CR/PRCR/PR
CB/PBCB/PB
TV
Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
OUT
FLASHER IN
DC OUT1 2
1 2
R L
F RO NT B C EN TE R
SURROUND BACK/MULTISPEAKER/
SPEAKER C
ON
OFF
SPEAKER C
OUTPUTINPUT-2INPUT-1 DVI-D
120V 60HZ
AC OUTLETS
UNSWITCHED1A 120W MAX
SWITCHED1A 120W MAX
SPEAKER SYSTEMSFRONTA OR B, CENTER,SURR,SURR BACK
:MINI MUM 6 OHMSFRONTA AND B:MINIMUM 8 OHMS
AC IN
tq w e i o
!9 !8
y ur
!0!1!2!4!7 !6
@0
!5
!5
!3
-
8/3/2019 Dfu Sr7500 Final Eng
11/56
8
EN
GLISH
REMOTE CONTROLLER
RC8500SR
NAMES AND FUNCTIONS
z Infrared Transmitter and LearningSensor
This transmitter emits infrared light. Press thebuttons while pointing the transmitter towards theinfrared receiver window of the SR7500 or otherAV equipment. Be sure to also point towards otherremote controls when using the learning function.
x POWER ON and OFF buttons
(When AMP mode is selected)These buttons are used to turn the SR7500 on oroff.
c SOURCE ON/OFF buttonThis button is used to turn a specific source (suchas a DVD player) on or off independently from therest of the system.
v M (Mode) buttonThis button is used to program Macros. Pressingthis button switches between Normal mode andMacro mode.The > button is used to move to the next page. Upto 20 programs (4 pages) can be made. Holdingdown the M button for three seconds or moreswitches to the Setup mode, where the Setup
menu is shown on the LCD. The Setup menu hasfour pages, and the > button is used to move to thenext page. Pressing the > button from page 4returns you to page 1.
b D1 to D5 (Direct) buttonsFive types of direct operations can be performedfor each of the 12 source buttons such as the DVD,television, amplifier, and other AV equipment. Thepages can be switched, so 4 pages 5 types = 20operations can be performed for a single source.The text display can also be changed.
n > (Page) buttonThis button is used to switch pages for the Direct
button. The current page is shown on the LCD.
m VOL (Volume) buttonThis button is used to adjust the volume for theamplifier and television.
Note:
Set the AMP mode to use this button with theSR7500.
2 31
5 64
8
0
97
MEMOCLEAR
DSS
AMPAUX2AUX1TAPE
TUNER CD CD-R MD
VCRDVDTV
SOURCE
OFFON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOLCH
PREV MUTE
MENU EXIT
GUIDE
T ES T C H. SEL
LIPSYNC
THX
SURR
7.1CH ATT SPK-AB
DISP OSD SLEEP
1 2
LIGHT
Learning Remote Controller
RC8500SR
z
cv
b
n
x
m
,
.
1
26
7
8
9
0
1
3
4
5
0
!7 REMOTE CONT. IN/OUT terminalsConnect to a Marantz component equipped withremote control (RC-5) terminals.
!8 AUDIO IN/OUT (CD, TAPE, CD-R, TV,DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs.There are 7 audio inputs (4 of which are linked tovideo inputs) and 4 audio outputs (2 of which arelinked to video outputs). The audio jacks arenominally labeled for cassette tape decks,compact disc players, DVD players and etc.... The
audio inputs and outputs require RCA-typeconnectors.
!9 DIGITAL INPUT (Dig.1 - 6) / OUTPUT(coaxial, optical)
These are the digital audio inputs and outputs.There are 3 digital inputs with coaxial jacks, 3 withoptical jacks.The inputs accept digital audio signals from acompact disc, LD, DVD, or other digital sourcecomponent.For digital output, there is 1 coaxial output and 1optical output.The digital outputs can be connected to MDrecorders, CD recorders, DAT decks, or other
similar components.
@0 DVI-D INPUT / OUTPUT (SR8500 only)This unit has two DVI-D inputs and one DVI-Doutput. The input function can be selected from theSETUP MAIN MENU.
, MUTE buttonThis button is used to mute the audio for theSR7500 and television.
Note:
Set the AMP mode to use this button with theSR7500.
. GUIDE buttonThis button is used to display the menus for theDVD player, DSS (satellite broadcasting tuner), orother AV equipment.
(when AMP mode is selected)This button is used to select the LIP.SYNC mode.
0 EXIT button
(when AMP mode is selected)This button is used to cancel settings in the setupmenu.
1 Numeric buttonsThese buttons are used to switch between 0 to 9 ofthe source components. If the source is set to theamplifier, these buttons are used to performoperations.
(when AMP mode is selected)
(1) TEST buttonUsed to enter the test tone menu.
(2) CH SEL. (channel select) buttonUsed to call up SETUP MAIN MENU and adjustspeaker levels or 7.1 ch input level.
(3) SURR (surround) buttonUsed to select the surround mode.
(4) 7.1CH buttonPress this button to select the output of an externalmulti channel decoder.
(5) ATT buttonWhen the input signal is too high and the voicedistorts even by throttling the SR7500 VOLUMEcontrol, turn on this function. ATT is indicatedwhen this function is activated.
The input level is reduced. Attenuator is invalid foruse with the output signal of REC OUT.
Note:
This function is unavailable during the digitalinput is selected.
(6) SPK-AB buttonSpeaker mode is switched in the followingsequence.
A B A+B off
-
8/3/2019 Dfu Sr7500 Final Eng
12/56
9
ENGLISHLCD INDICATORS
Information about currently selected source anddirect code names are displayed on the LCD.
A Source Name indicatorThis displays the name of the selected source,such as DVD, television, or other AV equipment(up to five characters).
B Direct Button Name indicator
This displays up to 20 types of button names foreach source. (up to six characters)
C Page indicatorThis displays the current page position.
D Transmission indicatorThis lights up when the remote control is sending asignal.
E USE indicatorThis is displayed under normal operation.
F Battery Level indicatorThis is displayed when the battery level is low.
G TIMER indicatorThis is displayed when the macro timer is set.
H MACRO indicatorThis is displayed when the remote control is inmacro programming mode.
LEARN
NAME
MACRO
USE PAGE 1 2 3 4
A
B
C
D
EF
G
HI
J
(7) DISP. buttonSelects the display mode for the front display of theSR7500.
(8) OSD buttonWhen this button is pressed, the current setting aredisplayed on the TV monitor.
(9) SLEEP (sleep timer) buttonThis button is used for setting the sleep timer. Itcan be operated the same way as the button inunit.
(0) THX buttonUse this button to select the THX mode.
2 MEMO buttonThis button is used to store settings to memory orprogram a source.
3 CONTROL buttonThses buttons are used when operating the PLAY,STOP, PAUSE, and other commands of a source.
Note:
This button is unavailable for the SR7500.
4 SOURCE buttonThses buttons are used to switch the source of
your A/V Receiver / amplifer. Each time a sourcebutton is pressed, the remote control changes tothe source which was pressed.This remote control can control 12 types ofequipment. To change the A/V Receiver / amplifiersource, press this button twice within two seconds.The signal is sent when it is pressed the secondtime.
Note:
Select the AMP as the source to use this remotecontroll with the SR7500.
5 LIGHT 1 and 2 buttonsPressing these buttons will light up the LCD and itsbuttons. This lighting time can be set. If the lighting
time is set to 0 seconds, the backlight turns on onlywhile this button is pressed. The operations forLIGHT 1 and 2 are identical.
6 CLEAR buttonThis button is used to erase the memory orprogram of a source.
7 MENU button
(when AMP mode is selected)This button is used to call up the SETUP MAINMENU of the SR7500.
8 PREV (Previous) buttonThis button is used to return to the previouschannel on the television or other device.
Note:
This button is unavailable for SR7500.
9 CH (Channel) buttonThis is used to change channels.
0 CURSOR buttonsThese buttons are used when controlling thecursor of the SR7500, DVD, or other AVequipment.
1 LCDInformation about the sources and modes areshown on the LCD.
I NAME indicatorThis is displayed when the remote control is inrenaming mode.
J LEARN indicatorThis is displayed when the remote control is inlearning mode.
-
8/3/2019 Dfu Sr7500 Final Eng
13/56
10
EN
GLISH
REMOTE CONTROL RANGE
The distance between the transmitter of theremote control and the IR SENSOR of the SR7500should be less than 5 meters. If the remote controlis pointed in a direction other than the IR SENSORor if there is an obstacle between them, use of theremote control may not be possible.
Remote-controllable range
LOADING BATTERIESThe life of the batteries used with the remote controlis about 4 months with normal use. Also be sure toreplace batteries earlier when you notice that theyare getting weak.
1. Remove the back cover.
2. Insert the new batteries (AAA type) withcorrect and polarity.
3. Close the cover until it clicks.
CAUTIONS ON BATTERIES
Use AAA type batteries in this remote controlunit.
If the remote control unit does not operate fromclose to the main unit, replace the batteries withnew ones, even if less then a year has passed.
The included battery is only for verifyingoperation. Replace it with a new battery as soonas possible.
When inserting the batteries, be careful to do soin the proper direction, following the + and -marks in the remote control unit s batterycompartment.
To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat ordispose of batteries in flames.
Remove the batteries when not planning to usethe remote control unit for a long period of time.
If the batteries should leak, carefully wipe off thefluid from the inside of the battery compartment,then insert new batteries.
When disposing of used batteries, pleasecomply with governmental regulations orenvironmental public instructions rules thatapply in your country or area.
Remote control unit (RC8500SR)
SR7500
BATTERY REPLACEMENT INTERVAL
Under normal usage, alkaline batteries lastapproximately four months. When the batterieswear out, a battery mark is displayed on the LCD.Although the remote control can still be used whenthe battery mark is displayed, the batteries shouldbe replaced as soon as possible. The LCDeventually starts to flash when buttons arepressed, the remote control will be unable totransmit signals or learn codes.
This remote control uses non-volatile memory
so that the learned codes and macro programsare retained even if the batteries are removed.
Reset the clock after replacing the batteries.
Safety Precautions for BatteriesBe sure to always observe the fol lowingprecautions to prevent fluid leakage, overheating,fire, breakage, accidental ingestion, and otheraccidents. If the batteries are left unused for a long period
of time, the battery fluid may leak or the batteriesmay corrode.
Do not use the batteries in the remote controlwith the plus and minus polarity reversed.
Do not attempt to recharge, heat, or disassemble
the batteries. Do not put the batteries in a fire. Do not use the remote control with old batteries
or worn-out batteries inserted.
Do not use different types of batteries or mix oldand new batteries in the remote control.
If the remote control is not operating properly,replace the batteries with new ones.
If any of the batteries are leaking, completelywipe up all leaked battery fluid, and then replacethe batteries with new ones.
SETTING THE TIME
Example: Setting to 6:20PM (18:20)
When you bought this remote control and insertthe batteries to the remote control at first, the steps1 to 3 are skipped.Starts from step 4 to set the time.
1. Hold down the M button for three seconds ormore.
The menu is displayed.
2. Press the > button once.This displays second page (SETUP).
3. Press the D4 (CLOCK) direct button.The indicator blinks and the clock indicatordisplays 0:00.
4. Press the 1 and 8 numeric button to set thehour indicator.
The hour indicator displays 18.The minute indicator blinks _.
5. Press the 2 and 0 numeric button to set theminute indicator.
The minute indicator displays 20.
The hour indicator blinks.
6. Press the OK cursor button to start the clock.The clock starts from 0 second at the time that wasset and return to normal (USE) mode.
Whenever the batteries are replaced, the clockshows 00:00. Please reset the clock. (The timesetting is not backed up.)
2 31
5 64
8
0
97
MEMOCLEAR
DSS
AMPAUX2AUX1TAPE
TUNER CD CD-R MD
VCRDVDTV
SOURCE
OFF ON/OFF
POWERON
D4
D5
D2
M
D1
D3
D5
OK
VOLCH
PREV MUTE
MENU EXIT
GUIDE
T ES T C H. SE L
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
1 2
LIGHT
LearningRemote Controller
RC8500SR
2.
6.
4.
5.
3.
3.
21
8
0
OK
D4
M
AVSURR
OUN
DRE
CEI V
ERS
R7500
PHONES
STANDB
Y
LC
RSL
SSR
LFE
DIGITAL
SURR
OUND
DISP
MULT
IAUT
OTU
NED
STSPK
RAB
V-OF
F
NIGH
T
PEA
K
ANALO
GDIGITA
L
ATT
SLE
EP
SURR
DIRECT
AUTO
DISC
6.1
MTX6.1
PCM
AAC
AUX1INPUT
AUDIO
S- VIDEO
DIGITAL
VIDEO
L
R
ENTER
DOW
N
UP
VOLUME
POWER
ON/ OF
F
INPUTSELECTOR
2
3
1
5
6
4
8
09
7
ME MO
C LEAR
D S S
A MP
A U X 2
A U X 1
T A P E
TU N ER
CD
C D - R
MD
VC R
D VD
T V
S OU R C E
O F F
ON / OFF
P OWE R
O N
D4
D5
D2
M
D1
D3
D5
OK
V O L
C H
PR EV
M U T
E
M E N U
EXI T
G UI D
E
TES T
CH.S
EL
SURR
7. 1CH
AT T
S P K - A B
DI S P
OSD
SLE E P
1
2
L I G H T L
e a rn in g
R e mo
te C o n tr
o lle r
R C 1 4
0 0
60
Approx
.5m
USE PAGE 1 USE PAGE 1 2
LEARN LEARN
LEARN
5 6
3 4
1 2
USE PAGE 1 2
-
8/3/2019 Dfu Sr7500 Final Eng
14/56
11
ENGLISH
TUNER MODE
AMP MODE
2 31
5 64
8
0
97
MEMOCLEAR
DSS
AMPAUX2AUX1TAPE
TUNER CD CD-R MD
VCRDVDTV
SOURCE
OFF ON/OFFPOWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOLCH
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL SURR
7.1CH ATT SPK-AB
DISP OSD SLEEP
1 2
LIGHT
Learning Remote ControllerRC8500SR
D1
D5
D4
D2
D3
D5
2 31
5 64
8 97
TEST CH.SEL SURR
7.1CH ATT
LIP.SYNC
SPK-AB
DISP OSD
THX
SLEEP
TUNER
0
CH
GUIDE
MEMOCLEAR
USE PAGE 1
2 31
5 64
8
0
97
MEMOCLEAR
DSS
AMPAUX2AUX1TAPE
TUNER CD CD-R MD
VCRDVDTV
SOURCE
OFF ON/OFFPOWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOLCH
PREV MUTE
MENU EXIT
GUIDE
T ES T C H. SE L S UR R
7.1CH ATT SPK-AB
DISP OSD SLEEP
1 2
LIGHT
Learning Remote ControllerRC8500SR
D1
D5
D4
D2
D3
D5
SOURCE
OFF ON/OFFPOWER
ON
OK
2 31
5 64
8 97
T ES T C H. SE L
LIP.SYNC
THX
SURR
7.1CH ATT SPK-AB
DISP OSD SLEEP
MENU
TAPE
DSS
AUX2AUX1
TUNER CD CD-R MD
VCRDVDTV
AMP
VOL
EXIT
MUTE
USE PAGE 1 2 3 4
CHECKING THE TIME
To check the time, hold down the > button for threeseconds or more. The current time is displayed forfive seconds.
Note:
Although the remote control uses a quartz clock,the time may become out of sync over the courseof operation. Be sure to correct the clock fromtime to time.
GENERAL INFORMATION OFRC8500SR TO SR7500
To control the SR7500 by your RC8500SR, youhave to select the device AMP or TUNER bypressing the function selector button. Please referbelow for the details in AMP and TUNER mode.
SOURCE ON/OFF Turns the SR7500 on and off
POWER ON Turns the SR7500 on
POWER OFF Turns the SR7500 o ff
D1 - D5 / >(Page) (Refer to page vi)
VOL +/- Adjust the over all sound level
MUTE Decreases the sound temporarily
Cursor Move the cursor for setting in On screen display mode
OK Enter the On screen display
Confirms the setting in On screen display mode
MENU Di spl ays the current setting on the monitor
EXIT Exits from SETUP MENU
TEST (1) Enter the test tone menu
CH.SEL (2) Call up SETUP MENU and adjusts speaker levels or 7.1ch
input level
SURR (3) Selects the surround mode
7.1CH ( 4) Selects the 7.1CH IN
ATT (5) Reduces the input level
SPK-AB (6) Selec ts t he speaker sys tem
DISP (7) Changes the front display mode
OSD (8) Selects the On screen display on and off
SLEEP (9) Set s the sleep timer function
THX (0) Selects the THX mode
Function selector Selects a particular source componentGUIDE / LIP.SYNC Selects the LIP.SYNC mode
D1 - D5 / >(Page) (Refer to page vi)
CH +/- Selects a preset station up and down
GUIDE Selects the Frequency direct input
09 Input the numeric
MEMO Enter the tuner preset memory numbers
CLEAR Clears the inputting
TUNER Selects a frequency band
-
8/3/2019 Dfu Sr7500 Final Eng
15/56
12
EN
GLISH
CONNECTIONSSPEAKER PLACEMENT
The ideal surround speaker system for this unit is7-speaker systems, using front left and rightspeakers, a center speaker, surround left and rightspeakers, a surround back left and right speakers,and a subwoofer.For best results we recommend that all frontspeakers be of the same type, with identical orsimilar driver units. This will deliver smooth pans
across the front sound stage as the action movesfrom side to side.Your center channel speaker is very important asover 80 % of the dialog from a typical motionpicture emanates from the center channel.It should possess similar sonic characteristics tothe main speakers. Surround channel speakersneed not be identical to the front channel speakers,but they should be of high quality.The surround center speaker is useful for playbackof Dolby Digital Surround EX or DTS-ES. One ofthe benefits of both Dolby Digital and DTS is thatsurround channels are discrete full range, whilethey were frequency limited in earlier Pro Logictype systems.Bass effects are an important part of home theater.For optimal enjoyment a subwoofer should be used
as it is optimized for low frequency reproduction. Ifyou have full range front speakers, however, theymay be used in place of a subwoofer with propersetting of the switches in the m enu system.
Front left and right speakersWe recommend to set the front L and R speakerswith 45-60 degrees from the listening position.
Center speakerAlign the front line of the center speaker with thefront L/R speakers. Or place the center speaker alittle backward from the line.
Surround left and right speakersWhen the SR7500 is used in surround operation,the preferred location for surround speakers is onthe side walls of the room, at or slightly behind thelistening position.The center of the speaker should face into theroom.
Surround back left and right speakersSurround back speakers are required when a full7.1-channel system is installed.Speakers should be placed on a rear wall, behindthe listening position.The center of the speaker should face into the
room.SubwooferWe recommend using a sub-woofer to have maximumbass effect. Sub-woofer bears only low frequencyrange so you can place it any where in the room.
HEIGHT OF THE SPEAKER UNITS
Front left and right speakers, and a center speakerAlign the tweeters and mid-range drivers on thethree front speakers at the same height, as best aspossible.
Surround left and right speakers, and surroundback speakerPlace the surround left, right and surround backspeakers higher than your ears by about 70cm1m. Also place the speakers at the same height, sabest as possible.
Note:
Use magnetically-shielded speakers for front left,right and the center speakers when the speakersare installed near the TV and the TV is a monitortype.
90110
22
30
135
150
0
CONNECTING SPEAKERS
AC IN
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTIRC
IN OUTDSS/VCR2IN OUT OUT
VCR1
VCR1
L
SBR
SBL
OUT
PRE
SLL
SRR
DSS/VCR2DVDTV
R
IN
R SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT IN
L SL
SBR
SBLCD
IN OUT SWOUT
CDR/MDTAPE
OUTIN
IN OUT
VIDEO
MONITOR
OUTMULTI VCR1TV
OUT
(AUX2)
MONITOR
D IG IT AL I N D IG IT AL O UT
4
1
OPT.
2
5
3
6
COAX.
R L RR
FRONTA
L L
FM (75)
ANTENNA
G ND A M
COMPONENT
VIDEO
CB/PBCR/PR
CR/PRCR/PR
CB/PBCB/PB
TV
Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
OUT
FLASHER IN
DC OUT1 2
1 2
R L
F RO NT B C EN TE R
SURROUND BACK/MULTISPEAKER/
SPEAKER C
ON
OFF
SPEAKER C
OUTPUTINPUT-2INPUT-1 DVI-D
120V 60HZ
AC OUTLETS
UNSWITCHED1A 120W MAX
SWITCHED1A 120W MAX
SPEAKER SYSTEMSFRONTA OR B,CENTER,SURR, SURR BACK
:MINIMUM6 OHMSFRONTA AND B:MINIMUM8 OHMS
RR
FRONTA
L L
SURROUNDCENTER
R L
SURROUND BACK/MULTISPEAKER/
SPEAKER C
ON
OFF
SPEAKER C
OUT
PRE
SW
INVERTOUTPUT
INPUTLEVEL
B TL R EM OT E C ON T.EXT. CONT. IN
VIDEO/+5~13V DC
S Y S T E M OU T O U T
INPUT
MASTERSLAVE
M I N M A XIN
FUSE
SPEAKER SYSTEMMINIMUM 4 OHMS
POWEREDSUBWOOFERPOWER
AMPLIFIERPASSIVE
SUBWOOFER
FRONTRIGHT LEFT
SURROUNDSURROUND
BACK
CENTER
orRIGHT LEFT
CONNECTING SPEAKER WIRE
1. Strip away approx. 3/8 inch (10 mm) of wireinsulation.
2. Twist the bared wire ends tight, to preventshort circuits.
3. Loosen the knob by turning it counterclockwise.4. Insert the bare part of the wire into the hole in
side of each terminal.
5. Tighten the knob by turning it clockwise tosecure the wire.
1. 2.
3. 4. 5.
3/8 inch(10 mm)
Front Right
Front Left
Front Center
Surround LeftSubwoofer
Surround BackLeft
Surround Right
Surround BackRight
RIGHT LEFT
70cm
1m
-
8/3/2019 Dfu Sr7500 Final Eng
16/56
13
ENGLISH
Caution:
Be sure to use speakers with the specified impedanceas shown on the rear panel of this unit.
To prevent damage to circuitry, do not let the barespeaker wires toucheach other and donot let them touchany metal part ofthis unit.
Do not touch thespeaker terminalswhen the power ison. It may cause
you to receive an electric shocks. Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage thisunit.
Note:
Be sure to connect the positive and negative cablesfor the speaker properly. If they are miss-connected,the signal phase will be reversed and the signalquality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connecta powered subwoofer (power amplifier built in ).If your subwoofer is a passive type (power amplifieris not built in), connect a monaural power amplifier
to the PRE OUT SUBWOOFER jack and connectthe subwoofer to the amplifier.
CONNECTING AUDIO COMPONENTS
A C I N
M U L T I
O U T
T V D V D
C
I N O U T
S - V I D E O
D V D
D S S / V C R 2
C
R S - 2 3 2 C
M U L T I R C
I N O U T
D S S / V C R 2
I N O U T O U T
V C R 1
V C R 1
L
S B R
S B L
O U T
P R E
S LL
S RR
D S S / V C R 2 D V DT V
R
IN
R S W
R C - 5
IN
S R
A U D I O
7 . 1 C H
IN
O U T I N
L S L
S B R
S B LC D
I N O U T S W O U T
C D R / M D T A P E
O U TIN
I N O U T
V I D E O
M O N I T O R
O U T
M U L T I
V C R 1
T V
O U T
( A U X 2 )
M O N I T O R
D I G I T A L I N D I G I T A L O U T
4
1
O P T .
2
5
3
6
C O A X .
R L RR
F R O N T A
L L
F M
(
7 5
)
A N T E N N A
G N D A M
C O M P O N E N T
V I D E O
C B
/
P B
C R
/
P R
C R
/
P R
C R
/
P R
C B
/
P B
C B
/
P B
T V
Y Y
M O N I T O R O U T
V C R 1
D V D D S S / V C R 2
Y
S U R R O U N D
1 0 0 W M A X .
A C O U T L E T
S W I T C H E D
2 3 0 V 5 0 / 6 0 H Z
O U T
S P E A K E R S Y S T E M S
F R O N T A O R B , C E N T E R , S U R R , S U R R B A C K
: 6
-
8 O H M S
F R O N T A
+
B : 8 O H M S
F L A S H E R I N
D C O U T
1 2
1 2
R L
F R O N T B C E N T E R
S U R R O U N D B A C K /
M U L T I S P E A K E R /
S P E A K E R C
O N
O F F
S P E A K E R C
O U T P U T I N P U T - 2 I N P U T - 1
D V I - D
A U D I O
IN
C D
I N O U T O U T
C D R / M D T A P E
D I G I T A L I N
1
6
D I G I T A L O U T
O P T .
OUT IN
L
R
L
R
OUT
L
R
L RL R L R
RL RL RL
OUT IN
L
R
L
R
DIGITALINPUT
DIGITALOUTPUT
DIGITALOUTPUT
R L
R L R L
RL
L
R
The output audio signal from the TAPE OUT jackand the CD-R/MD OUT jack is the same signal whichis currently selected.
Caution:
Do not connect this unit and other components tomains power until all connections betweencomponents have been completed.
Notes:
Insert all plugs and connectors securely.Incomplete connections may make noise.
Be sure to connect the left and right channelsproperly.
Red connectors are for the R (right) channel, andwhite connectors are for the L (left) channel.
Be sure to connect input and output properly.
Refer to the instructions for each component thatis connected to this unit.
Do not bind audio/video connection cables withpower cords and speaker cables this will result ingenerating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
There are 6 digital inputs, 3 coaxial jacks and 3optical jacks, on the rear panel. You can usethese jacks to input PCM, Dolby Digital and DTSbitstream signals from a CD, DVD, or otherdigital source components.
There is one digital output coaxial jack and oneoptical output jack on the rear panel. These
jacks can be connected to a CD recorder-, or aMD deck inputs, respectively.
Refer to the instructions for each component. Tosetup the digital audio format of DVD player, orother digital sources connected to digital input
jacks.
Use fiber optical cables (optical) for DIG-1,2,3input jacks. Use 75 ohms coaxial cables (fordigital audio or video) for DIG-4, 5, 6 input jacks.
You can designate the input for each digitalinput/output jacks according to your component.See page 19.
CD RECORDER / MD DECKCD PLAYER TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO(COAXIAL)
DIGITAL AUDIO(OPTICAL)
Notes:
There is no Dolby Digital RF input jack. Pleaseuse an external RF demodulator Dolby Digitaldecoder when connecting the Dolby Digital RFoutput jack of the video disc player to the digitalinput jack.
The digital signal jacks on this unit conform to theEIA standard. If you use a cable that does notconform to this standard, this unit may notfunction properly.
Each type of audio jack works independently.
Signals input through the digital and analog jacksare output through the corresponding digital andanalog jacks, respectively.
-
8/3/2019 Dfu Sr7500 Final Eng
17/56
14
EN
GLISH
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTIRC
IN OUTDSS/VCR2IN OUT OUT
VCR1
VCR1
L
SBR
SBL
OUT
PRE
SLL
SRR
DSS/VCR2DVDTV
R
IN
R SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT IN
L SL
SBR
SBLCD
IN OUT SWOUT
CDR/MDTAPE
OUTIN
IN OUT
VIDEO
MONITOR
OUTMULTI VCR1TV
OUT
(AUX2)
MONITOR
D IG IT AL I N D IG IT AL OU T
4
1
OPT.
2
5
3
6
COAX.
RR
FRONT A
L
FM (75)
ANTENNA
G ND A M
COMPONENTVIDEO
CB/PBCR/PR
CR/PRCR/PR
CB/PBCB/PB
TV
Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
OUT
SPEAKER SYSTEMSFRONTA OR B,CENTER,S
:MINIMUMFRONTA AND B: MINIMUM
FLASHER IN
DC OUT1 2
1 2
R L
F
SURROUND BACK/MULTISPEAKER/
SPEAKER C
SPEAKER C
OUTPUTINPUT-2INPUT-1 DVI-D
DVDIN OUT
VCR1
VIDEO
DVDIN OUT
VCR1
S-VIDEO
OUTMONITOR
COMPONENTVIDEO
CR/PRCB/PBY
MONITOR OUT
5
VCR1DVD
AUDIO
IN OUT
DVD
OUTPUTINPUT-1
L R
AUDIOOUT
DIGITALOUT
VIDEOOUT
S-VIDEOOUT
S-VIDEOIN
DVI-DIN
L R
AUDIOOUT
AUDIOIN
L R
VIDEOOUT IN
S-VIDEOOUT IN
Y CB/PB CR/P R
COMPONENTVIDEO OUT
Y CB/P B CR/PR
COMPONENTVIDEO IN
DVI-DOUT
L R L R
L R
L R L R LR
M U L T I
O U T
T V D V D
C
I N O U T
S - V I D E O
D V D
D S S / V C R 2
C
R S - 2 3 2 C
M U L T I R C
I N O U T
D S S / V C R 2
I N O U T O U T
V C R 1
V C R 1
L
S B R
S B L
O U T
P R E
S LL
S RR
D S S / V C R 2 D V DT V
R
IN
R S W
R C - 5
IN
S R
A U D I O
7 . 1 C H
IN
O U T I N
L S L
S B R
S B LC D
I N O U T S W O U T
C D R / M D T A P E
O U TIN
I N O U T
V I D E O
M O N I T O R
O U T
M U L T I
V C R 1
T V
O U T
( A U X 2 )
M O N I T O R
D I G I T A L I N D IG I T A L O U T
4
1
O P T .
2
5
3
6
C O A X .
F M
(
7 5
)
A N T E N N A
G N D A M
C O M P O N E N T
V I D E O
C B
/
P B
C R
/
P R
C R
/
P R
C R
/
P R
C B
/
P B
C B
/
P B
T V
Y Y
M O N I T O R O U T
V C R 1
D V D D S S / V C R 2
Y
O U T
F L A S H E R I N
D C O U T
1 2
1 2
O U T P U T I N P U T - 2 I N P U T - 1 D V I - D
T V
V I D E O
D S S / V C R 2
I N O U T
M O N I T O R
IN
S - V I D E O
O U T
M O N I T O R
L
D S S / V C R 2
R
A U D I O
IN
D I G I T A L I N
2
T V
D S S / V C R 2
L R
AUDIOOUT
DIGITALOUT
VIDEOOUT
S-VIDEOOUT
AUDIOOUT
L R
VIDEOOUT
S-VIDEOIN
VIDEOIN
LR
L
R
L R
L R
L R
CONNECTING VIDEO COMPONENTS
ANALOG AUDIO
VIDEO
S-VIDEO
DVD PLAYER VIDEO PROJECTOR SATELLITE TUNER
DIGITAL AUDIO(COAXIAL)
VCR TV
VIDEO, S-VIDEO, COMPONENT JACKS
There are 3 types of video jacks on the rear panel.
VIDEO jackThe video signal for the VIDEO jacks is theconventional composite video signal.
S-VIDEO jackThe video signal is separated into luminance (Y)and color (C) signals for the S-VIDEO jack. The S-VIDEO signals enables high-qual i ty colorreproduction. If your video component has an S-VIDEO output, we recommend to use it. Connectthe S-VIDEO output jack on your video component
to the S-VIDEO input jack on this unit.Component jackMake component video connections to a TV ormonitor with component inputs to produce higherquality video images. Use a component video cableor 3 video cords to connect the component videoout jacks on the SR7500 to the monitor.
DVI-D jack (SR8500 only)This unit has two DVI-D inputs and one DVI-D output.It can send digital signals from DVDs and othersources directly to a display. It minimizes signaldegradation caused by analog conversion so thathigh quality images can be enjoyed. Select an inputsource from the SETUP MAIN MENU. (See page 19.)
Notes:
Be sure to connect the left and right audio channelsproperly.
Red connectors are for the R (right) channel, andwhite connectors are the for L (left) channel.
Be sure to connect the inputs and outputs of thevideo signals properly.
If you connect the S-VIDEO or component signal tothe S-VIDEO or component jack on this unit, it is notnecessary to connect the conventional video signal tothe VIDEO (composite) jack. If you use both videoinputs, this unit gives priority to the S-VIDEO signal.
Each type of video jack works independently.Signals input to the VIDEO (composite) and S-VIDEO jacks or component are output to thecorresponding VIDEO (composite) and S-VIDEO
or component jacks, respectively. This unit has the TV-AUTO ON/OFF function to
turn the TV ON or OFF automatically, by sensingthe incoming video signal from the VIDEO jacks.
You may need to setup the digital audio outputformat of your DVD player, or other digital sourcecomponents. Refer to the instructions of the eachcomponent connected to the digital input jacks.
There is no Dolby Digital RF input jack. Pleaseuse an external RF demodulator with a DolbyDigital decoder to connect a video disc playerwhich has a Dolby Digital RF output jack to thedigital input jack on this unit.
DIGITAL AUDIO(OPTICAL)
SR8500only
Note (SR8500 only):
When a device with DVIou tpu t tha t suppor t sHDCP is connected to adevice that does notsupport HDCP, signalsare not output. To viewimages in DVI, i t isnecessary to connect adisplay that supportsHDCP.
There may be no Imageoutput if connected to aTV or display that is notcompatible with the aboveformat.
Refer to the instructionmanual of the TV ordisplay to be connected tothis unit for detailedinformation regarding theDVI-D terminal.
*HDCP: High-bandwidth DigitalContent Protection
-
8/3/2019 Dfu Sr7500 Final Eng
18/56
15
ENGLISH
AC IN
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTIRC
IN OUTDSS/VCR2IN OUT OUT
VCR1
VCR1
L
SBR
SBL
OUT
PRE
SLL
SRR
DSS/VCR2DVDTV
R
IN
R SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT IN
L SL
SBR
SBLCD
IN OUT SWOUT
CDR/MDTAPE
OUTIN
IN OUT
VIDEO
MONITOROUT
MULTI VCR1TVOUT
(AUX2)
MONITOR
D IG IT AL IN D IG IT AL OU T
4
1
OPT.
2
5
3
6
COAX.
R L RR
FRONTA
L L
FM (75)
ANTENNA
G ND A M
COMPONENT
VIDEO
CB/PBCR/PR
CR/PRCR/PR
CB/PBCB/PB
TV
Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
100WMAX.
AC OUTLET
SWITCHED230V 50/60HZ
OUT
SPEAKER SYSTEMSFRONTA OR B,CENTER,SURR,SURR BACK
:6 -8 O H MSFRONTA + B : 8 OHMS
FLASHER IN
DC OUT1 2
1 2
R L
F RO NT B C EN TE R
SURROUND BACK/MULTISPEAKER/
SPEAKER C
ON
OFF
SPEAKER C
OUTPUTINPUT-2INPUT-1
USB IN
DVI-D
C
SRR
7.1CH
IN
L SL
SBR
SBL
SW
C
SBR
SBL
OUT
PRE
SLL
R SWSR
L
R
FRONT SURR. SURR.BACK
SUBWOOFER
CENTER
L
R
FRONT SURR. SURR.BACK
SUBWOOFER
CENTER
RL RL RL
LR
R L
LR LR
R L
R L R LR L
R L
ADVANCED CONNECTING
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audiosource such as a SACD multichannel player, DVDaudio player or external decoder.If you use these jacks, switch on the 7.1CH INPUTand set the 7.1CH INPUT level by using theSETUP MAIN MENU. See page 23.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting externalpower amplifiers.Be sure to connect each speaker to the correspondingexternal power amplifier.
POWERAMPLIFER
DVD AUDIO PLAYERor
SACD MULTI CHANNELPLAYER
CenterFrontLeft
FrontRight
SurroundLeft
SurroundRight
Subwoofer
SurroundBack Left
A C I N
M U L T I
O U T
T V D V D
C
I N O U T
S - V I D E O
D V D
D S S / V C R 2
C
R S - 2 3 2 C
M U L T I R C
I N O U T
D S S / V C R 2
I N O U T O U T
V C R 1
V C R 1
L
S B R
S B L
O U T
P R E
S LL
S RR
D S S / V C R 2 D V DT V
R
IN
R S W
R C - 5
IN
S R
A U D I O
7 . 1 C H
IN
O U T I N
L S L
S B R
S B LC D
I N O U T
S W
O U T
C D R / M D T A P E
O U TIN
I N O U T
V I D E O
M O N I T O R
O U T
M U L T I
V C R 1
T V
O U T
( A U X 2 )
M O N I T O R
D I G I T A L I N D I G I T A L O U T
4
1
O P T .
2
5
3
6
C O A X .
R L RR
F R O N T A
L L
F M
(
7 5
)
A N T E N N A
G N D A M
C O M P O N E N T
V I D E O
C B
/
P B
C R
/
P R
C R
/
P R
C R
/
P R
C B
/
P B
C B
/
P B
T V
Y Y
M O N I T O R O U T
V C R 1
D V D D S S / V C R 2
Y
S U R R O U N D
1 0 0 W M A X .
A C O U T L E T
S W I T C H E D
2 3 0 V 5 0 / 6 0 H Z
O U T
S P E A K E R S Y S T E M S
F R O N T A O R B , C E N T E R , S U R R , S U R R B A C K
: 6
-
8 O H M S
F R O N T A
+
B : 8 O H M S
F L A S H E R I N
D C O U T
1 2
1 2
R L
F R O N T B C E N T E R
S U R R O U N D B A C K /
M U L T I S P E A K E R /
S P E A K E R C
O N
O F F
S P E A K E R C
O U T P U T I N P U T - 2 I N P U T - 1
D V I - D
R C - 5
REMOTECONTROL
REMOTECONTROL
REMOTECONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
1
RC OUT
2
CONNECTING THE REMOTE CONTROL JACKS
MD DECKCD RECORDER
qYou can control other Marantz products throughthis unit with the remote control by connecting theREMOTE CONTROL terminals on each unit.The signal transmitted from the remote control isreceived by the remote sensor on this unit. Thenthe signal is sent to the connected device throughthis terminal. Therefore you need to aim theremote signal only to the unit. Also, if a Marantzpower amplifier (some models excluded) isconnected to one of these terminals, the poweramplifiers, power switch is synchronized with thisunits power switch.
Set the REMOTE CONTROL SWITCH on the units,other than the main unit to EXT.(EXTERNAL) forthis feature.
CD PLAYER
OPTION
wWhenever external infrared sensors or similardevices are connected to RC-5 IN of the SR7500,be sure to always disable operation of the infraredsensor on the main unit by using the followingprocedure.
1. Hold down the MULTI button and the MENUbutton on the front