DAVCO K10 PLUS PH FINAL Documents/Products/DAVCO K10 PLUS P… · DAVCO K10 PLUS PH is a flexible...

2
Store in a cool, dry place. Shelf life is 12 months if properly stored in the original unopened container. Storage and Shelf Life Description DAVCO K10 PLUS PH is a flexible single pack water – based waterproofing and sealing membrane which is capable of curing in approximately 4-8 hours depending on the number of coats and temperature. Advantages Single pack, Easy to use Excellent curing UV resistant Superb elongation Excellent tensile strength Anti – fracture, no blistering No tar, no bitumen, non – toxic Colors Grey, White, and Beige Technical Data Appearance : Thick pasty liquid Solid content : 60 – 70% Adhesion to concrete : 1.0 MPa Hardness (Shore A) : 80 Curing time at 30°C : 4-8 hours Crack Bridging (ASTM C836) : > 2mm Elongation : 300 - 500% at 28 days *Specifications are subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions. Coverage Approximately 0.7kg/m 2 /coat (depending on site condition) Packaging 4L and 16L pail Precautions Temperature range to use: 10°C to 35°C Do not use where negative hydrostatic pressure is evident. Surfaces must not allow water to stagnate or form a pond. Clean brushes, rollers and trays with water before product dries. Do not mix sand and admixtures to DAVCO K10 PLUS PH. Uses Ideal for waterproofing of facades, terraces, balconies and wet areas Ideal for waterproofing of concrete roofs For internal and external use

Transcript of DAVCO K10 PLUS PH FINAL Documents/Products/DAVCO K10 PLUS P… · DAVCO K10 PLUS PH is a flexible...

Page 1: DAVCO K10 PLUS PH FINAL Documents/Products/DAVCO K10 PLUS P… · DAVCO K10 PLUS PH is a flexible single pack water – based waterproofing and sealing membrane which is capable of

�����������������

��������������������������� ������������������������������������������������������������������������� ������������������ ��������������������������������������� ��������������������������������������������������������� ����������������������������������� ���������

���������������������������������������������� � �����­������������­���������� �� ��������������������������

����������������� �����������  �������������������������������������������������������������������������� ��������������������� ����������������������������������� ����­����

������������������������������������������������������������������������������������������� ����������������������� ���������������������������������¡��¡��� �������������������¡��¡���

��������� ����������������������������¡���������������������������������������������������

���

Store in a cool, dry place. Shelf life is 12 months if properly stored in the original unopened container.

Storage and Shelf Life

DescriptionDAVCO K10 PLUS PH is a flexible single pack water – based waterproofing and sealing membrane which is capable of curing in approximately 4-8 hours depending on the number of coats and temperature.

Advantages• Single pack, Easy to use• Excellent curing• UV resistant • Superb elongation• Excellent tensile strength • Anti – fracture, no blistering • No tar, no bitumen, non – toxic

ColorsGrey, White, and Beige

Technical DataAppearance : Thick pasty liquidSolid content : 60 – 70%Adhesion to concrete : 1.0 MPaHardness (Shore A) : 80Curing time at 30°C : 4-8 hoursCrack Bridging (ASTM C836) : > 2mmElongation : 300 - 500% at 28 days

*Specifications are subject to change without notification. Resultsshown are typical but reflect test procedures used. Actual fieldperformance will depend on installation methods and site conditions.

CoverageApproximately 0.7kg/m2/coat (depending on site condition)

Packaging4L and 16L pail

Precautions• Temperature range to use: 10°C to 35°C• Do not use where negative hydrostatic pressure is evident.• Surfaces must not allow water to stagnate or form a pond.• Clean brushes, rollers and trays with water before product dries.• Do not mix sand and admixtures to DAVCO K10 PLUS PH.

������ ������������������������ ���� ������������������������ ������� ������ ��

Uses• Ideal for waterproofing of facades, terraces, balconies and wet areas• Ideal for waterproofing of concrete roofs • For internal and external use

Page 2: DAVCO K10 PLUS PH FINAL Documents/Products/DAVCO K10 PLUS P… · DAVCO K10 PLUS PH is a flexible single pack water – based waterproofing and sealing membrane which is capable of

�����������������

��������������������������� ������������������������������������������������������������������������� ������������������ ��������������������������������������� ��������������������������������������������������������� ����������������������������������� ���������

���������������������������������������������� � �����­������������­���������� �� ��������������������������

����������������� �����������  �������������������������������������������������������������������������� ��������������������� ����������������������������������� ����­����

������������������������������������������������������������������������������������������� ����������������������� ���������������������������������¡��¡��� �������������������¡��¡���

��������� ����������������������������¡���������������������������������������������������

���

������ ������������������������ ���� ������������������������ ������� ������ ��

How To UseSurface Preparation: Concrete• All new concrete slabs must be allowed to cure for at least 6 weeks.• Old concrete must be cleaned with a strong commercial grade detergent or de-greaser. Thoroughly wash off all residue with clean water and allow the surface to dry for at least 24 hours.

Product preparation:• No dilution / mixing with water is required when using DAVCO K10 PLUS PH.• Body Coat/Top Coat: Stir the product well before using.

Priming:• For smooth finished surfaces / substrates, old concrete and G.I roofs, use DAVCO K10 ACRYLIC PRIMER.

Application:• All substrates must be cleaned and sound prior to waterproofing.• The substrate must be visibly dry.• Spread DAVCO K10 PLUS PH onto the substrate using a roller, brush, steel trowel or spray.• Apply in a thin layer over the area to be waterproofed.• Allow 1 to 2 hours in between each coat depending on thickness and atmospheric conditions.• Recommended coverage is 0.7kg/m2 @ 0.7mm thick in minimum 2 coats.• Minimum thickness for roofdecks is 2mm of the applied product.• Tools and excess DAVCO K10 PLUS PH must be cleaned up while still wet.