Copyright © 2010 – Gasparini GASPARINI ACCESSORIESACCESSORIES.

Copyright © 2010 – Gasparini

GASPARINI

ACCESSORIESACCESSORIESACCESSORIESACCESSORIES


1. FRONT SUPPORTS

2. SHEET FOLLOWERS

3. LOWER TOOL CLAMPING

4. UPPER TOOL CLAMPING

5. GPS4 BENDING ANGLE CONTROL

6. FLATTENING BENCH

7. ROBOT INTEGRATION

8. PRESS BRAKE IN TANDEM


1. STANDARD CE

2. FSA-A

3. FSA-B

4. FSA-C

5. FSA-D

1. FRONT SUPPORTS


1. ZERO VERTICAL ADJUSTMENT

2. EASY TO REMOVE OR CHANGE POSITION

FRONT SUPPORTS: STANDARD CE



2. EASY TO REMOVE OR CHANGE POSITION

3. ALUMINUM PROFILE

4. BALLS (MADE OF PLASTIC ON REQUEST)

5. RULER

6. FRONT STOP

7. BRUSHES (ON REQUEST)

FRONT SUPPORTS: FSA-A


1. SLIDING BY LINEAR GUIDE


3. SIDE PARK

4. ALUMINIUM PROFILE


6. RULER

7. FRONT STOP


FRONT SUPPORTS: FSA-B



2. TWO VERTICAL PNEUMATIC POSITIONS


4. SIDE PARK



7. RULER

8. FRONT STOP


FRONT SUPPORTS: FSA-C

ESPECIALLY FOR HEMMING OPERATION


1. VERTICAL AXIS CONTROLLED BY CNC


3. SIDE PARK



6. RULER

7. FRONT STOP


FRONT SUPPORTS: FSA-D


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




ESPECIALLY FOR THIN AND LONG SHEET METAL



3. DEPTH ADJSTUMENT

4. SIDE PARK

5. PLASTIC BALLS AND BRUSHES (ON REQUEST)

6. R AXIS (ON REQUEST)

2. SHEET FOLLOWERS


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




A. MANUAL CLAMPING

B. PNEUMATIC CLAMPING ABC

C. HYDRAULIC CLAMPING


For machines L≤5m & F≤330t


D. CLAMPING FOR WILA DIES


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




A. MANUAL CLAMPING

B. PNEUMATIC CLAMPING

C. HYDRAULIC CLAMPING


For machines F≤330t


D. WILA MANUAL/HYDRAULIC CLAMPING (NSCL II)

E. HYDRAULIC CLAMPING FOR BEYELER TOOLS


F. HYDRAULIC CLAMPING IN THE RAM + PNEUMATIC CLAMPING


PUNCH STYLE


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




GPS4 ON: forks in TDC

GPS4R setting: the forks are pushed up

and aligned to the pre-setting device, this

position is memorized by CNC.

GPS4R during the bending: the forks are in contact with the

sheet metal and by the C measurement the angle bending

is measured

5. GPS4: BENDING ANGLE CONTROL


• H ≥ 60 mm• S ≥ 14 mm• L = 60 mm with V ≤ 80 • L = 100 mm with V >80

GPS4: MAIN DIMENSIONS

WILA DIES APPLICATION


GPS4: ADVANTAGES

1. NO BENDING TEST NEEDED (typical for an only/a few piece/s production)

2. FREE SPACE AROUND THE TOOLS

3. EASY TO PROGRAM (thickness, length, type of material and bending force do not need to be set)

4. MEASURE FROM BOTH SIDE OF THE SHEET METAL

5. NO VIRTUAL CONTACT WITH THE SHEET METAL

6. NOT THEORITICAL MEASUREMENT

7. UP TO FOUR WORKING STATIONS CAN BE USED


WHERE GPS4-R IS NOT APPLICABLE

1. MULTI V-DIES

2. DIES NOT SELF-CENTERING

3. VARIABLE V-DIES

4. SPECIAL DIES, LIKE Z-DIES (Rolleri CEZ), DIES OR SIMILAR

5. DIES WITH FLATTENING OR COINING

6. DIES WITH PLASTIC/RUBBER INSERTS

7. DIES WITH AN OPENING BIGGER OR EQUAL TO V160 (GPS4 is applicable up to V125 included)

8. V/t < 6:1 (OPENING DIE/SHEET THICKNESS, when ratio smaller than 6:1 is requested, please contact Gasparini to check if it feasible)

9. BENDING ANGLE LESS THAN 70° AND MORE 150°

10. DIES WITH ROLLERS

11. DIES WITH AN OPENING LESS THAN 8 mm (GPS4 is applicable from V8 included)


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. HEMMING BENCH




1. HEMMING TOOL ALWAYS INSTALLED

2. NO ADDITIONAL HEMMING TOOL NEEDED

6. HEMMING BENCH


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




1. ROBOT AND OPERATOR USE

2. ROBOT ONLY



ROBOT AND OPERATOR USE: FEATURES

1. HEAT EXCHANGER

2. OIL HEATING ELEMENTS

3. OIL TEMPERATURE DISPLAY ON EL. BOX

4. ADDITIONAL THERMOSTAT

5. OIL LEVEL ELECTROMAGNETIC CONTROL

6. CNC ON MOBILE SUPPORT ON FLOOR

7. SAFETY DEVICE (i.e. Laser Beam)

8. INTERFACE FOR ROBOT

9. SENSOR IN THE B.G. FINGERS


ROBOT ONLY USE: FEATURES

1. HEAT EXCHANGER

2. OIL HEATING ELEMENTS

3. OIL TEMPERATURE DISPLAY ON EL. BOX

4. ADDITIONAL THERMOSTAT

5. OIL LEVEL ELECTROMAGNETIC CONTROL

6. CNC ON MOBILE SUPPORT ON FLOOR

7. NO SAFETY DEVICE AND SIDE GUARDS

8. UP TO 20 mm/s WORK SPEED

9. INTERFACE FOR ROBOT

10. SENSOR IN THE B.G. FINGERS


1. FRONT SUPPORTS

2. SHEET FOLLOWERS




6. FLATTENING BENCH




8. PRESS BRAKES IN TANDEM1. LONGER BENDING LENGTH

2. DOUBLE PRODUCTION WITH SHORTER LENGTH

3. LIGTH BARRIER AS SAFETY DEVICE

Copyright © 2010 – Gasparini GASPARINI ACCESSORIESACCESSORIES.

Documents

Transcript of Copyright © 2010 – Gasparini GASPARINI ACCESSORIESACCESSORIES.