Convair Master Cool Manual
16
® OWNER’S MANUAL Portable Evaporative Cooler (English) (Mi MiC MiV) ILL863-A (MI) MILLENIA ILL863-A (MIV) MEGACOOL ILL1222-A (MIC) MASTERCOOL
-
Upload
mark-smith -
Category
Documents
-
view
48 -
download
2
description
Instruction manual for Convair Mastercool air conditioner
Transcript of Convair Master Cool Manual
®
OWNER’S MANUALPortable Evaporative Cooler
(English) (Mi MiC MiV)
ILL863-A
(MI)MILLENIA
ILL863-A
(MIV)MEGACOOL
ILL1222-A
(MIC)MASTERCOOL
CONTENTS
SAFETY 1
COMPONENT LOCATION 2
ASSEMBLY 3-4
DIRECTIONS FOR USE 4-6
MAINTENANCE 6 7
TROUBLESHOOTING 8
SPARE PARTS LIST & EXPLODED VIEW 9-10
WARRANTY 11
........................................................................General SafetyElectrical Safety
...........................................
..................................................................Caution - Check VoltageTo assemble the cooler
..............................................How to get the best cooling performanceFilling with waterUsing the cooler - Low fan speed
High fan speedFan only (vent)
Conditioning of Aspen cooling padsAir direction controlSafety instructionsCleaning the cooler/rear panel removal
............................................................ -To drain waterWater strainer and Aspen cooling padPump belt replacement / Drain Plug
..................................................
..................
.................................................................
Waste electrical products must not be disposed of with household waste. This productshould be taken to your local recycling centre for safe treatment.
i Millenia series Portable Evaporative Cooler
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electricalpower cord to a power outlet, check thatthe air cooler voltage is the same as yourpower supply (refer to the rating labellocated on the rear of the unit).
Do not pull the unit along by the powercord or place the power cord near asource of heat. Always unroll the powercord completely before use.
Switch off and unplug when not in use.
If the power supply cord is damaged itmust be replaced by the manufacturer, aservice agent or similarly qualifiedpersons in order to avoid a hazard.
Portable evaporative air cooler -important safety instructions
Please read these instructions beforeassembling the cooler and keep for futurereference.
This appliance is not intended for use bypersons (including children) with reducedphysical, sensory or mental capabilities, orlack of experience and knowledge, unlessthey have been given supervision orinstruction concerning use of the appliance bya person responsible for their safety.
Children should be supervised to ensure thatthey do not play with the appliance.
Clean the air inlets and outlets at regularintervals to prevent airflow reduction (referMaintenance section).
Do not store or operate the appliance nearany flammable substances.
During operation, water is present in thebottom tank of the air cooler. Be careful whenmoving the unit to prevent water from spilling.
General Safety
For indoor use only.
Use only in the upright position on a flat levelsurface and at least 50cm from any objects.
Do not place objects on the air cooler, orthrough the ventilating slots or restrict the airinlets & outlets.
Closely supervise any children and pets whenthe air cooler is in use.
Always switch your cooler off and unplug itbefore cleaning or maintenance.
CONTENTS
SAFETY 1
COMPONENT LOCATION 2
ASSEMBLY 3-4
DIRECTIONS FOR USE 4-6
MAINTENANCE 6 7
TROUBLESHOOTING 8
SPARE PARTS LIST & EXPLODED VIEW 9-10
WARRANTY 11
........................................................................General SafetyElectrical Safety
...........................................
..................................................................Caution - Check VoltageTo assemble the cooler
..............................................How to get the best cooling performanceFilling with waterUsing the cooler - Low fan speed
High fan speedFan only (vent)
Conditioning of Aspen cooling padsAir direction controlSafety instructionsCleaning the cooler/rear panel removal
............................................................ -To drain waterWater strainer and Aspen cooling padPump belt replacement / Drain Plug
..................................................
..................
.................................................................
Waste electrical products must not be disposed of with household waste. This productshould be taken to your local recycling centre for safe treatment.
i Millenia series Portable Evaporative Cooler
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electricalpower cord to a power outlet, check thatthe air cooler voltage is the same as yourpower supply (refer to the rating labellocated on the rear of the unit).
Do not pull the unit along by the powercord or place the power cord near asource of heat. Always unroll the powercord completely before use.
Switch off and unplug when not in use.
If the power supply cord is damaged itmust be replaced by the manufacturer, aservice agent or similarly qualifiedpersons in order to avoid a hazard.
Portable evaporative air cooler -important safety instructions
Please read these instructions beforeassembling the cooler and keep for futurereference.
This appliance is not intended for use bypersons (including children) with reducedphysical, sensory or mental capabilities, orlack of experience and knowledge, unlessthey have been given supervision orinstruction concerning use of the appliance bya person responsible for their safety.
Children should be supervised to ensure thatthey do not play with the appliance.
Clean the air inlets and outlets at regularintervals to prevent airflow reduction (referMaintenance section).
Do not store or operate the appliance nearany flammable substances.
During operation, water is present in thebottom tank of the air cooler. Be careful whenmoving the unit to prevent water from spilling.
General Safety
For indoor use only.
Use only in the upright position on a flat levelsurface and at least 50cm from any objects.
Do not place objects on the air cooler, orthrough the ventilating slots or restrict the airinlets & outlets.
Closely supervise any children and pets whenthe air cooler is in use.
Always switch your cooler off and unplug itbefore cleaning or maintenance.
2 Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEYA ControlsB Front grilleC Water filling doorD Water reservoirE CastorsF Water level indicatorG Front pillar (Millenia, Megacool)H BaseI Rear panel retaining screws (2)J Rear panelK Power cord entry pointL Reservoir drain plugM Rating labelN Cord storage hooksO Rear pillar (Millenia, Megacool)
B
D
C
E H
F
G
A
ILL864-A ILL865-B
K
L
J
I
N
M
O
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical powercord to a power outlet, check that thecooler voltage is the same as your powersupply. The cooler voltage will be statedon the rating label at the rear of thecooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locatingholes in the base. Use a rotating motionto assist in the entry of the steel springring (“ ” Fig 7).
*
7
ILL867-B
*Models Millenia and Megacool only
Assemble the front and rear pillars andscrew together. Place this assembly onthe base and slide into position until itlocks (Fig 8).
Models Millenia and Megacool only
Place the reservoir of the cooler onto thefront pillar as shown (Fig 9). Tiltdownwards towards the rear until thereservoir locks onto the rear pillar.
To remove the unit from the pillars, use ascrewdriver in the two recesses in therear of the reservoir to release the clips.Tilt the unit forward to remove.
ILL870-A
9
2 Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEYA ControlsB Front grilleC Water filling doorD Water reservoirE CastorsF Water level indicatorG Front pillar (Millenia, Megacool)H BaseI Rear panel retaining screws (2)J Rear panelK Power cord entry pointL Reservoir drain plugM Rating labelN Cord storage hooksO Rear pillar (Millenia, Megacool)
B
D
C
E H
F
G
A
ILL864-A ILL865-B
K
L
J
I
N
M
O
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical powercord to a power outlet, check that thecooler voltage is the same as your powersupply. The cooler voltage will be statedon the rating label at the rear of thecooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locatingholes in the base. Use a rotating motionto assist in the entry of the steel springring (“ ” Fig 7).
*
7
ILL867-B
*Models Millenia and Megacool only
Assemble the front and rear pillars andscrew together. Place this assembly onthe base and slide into position until itlocks (Fig 8).
Models Millenia and Megacool only
Place the reservoir of the cooler onto thefront pillar as shown (Fig 9). Tiltdownwards towards the rear until thereservoir locks onto the rear pillar.
To remove the unit from the pillars, use ascrewdriver in the two recesses in therear of the reservoir to release the clips.Tilt the unit forward to remove.
ILL870-A
9
4
®
Millenia series Portable Evaporative Cooler
Model Mastercool only
Place the reservoir onto the base andpress down to engage the four clips in thebase (Fig 10).
To remove the cooler from the base, tip itupside down and release the clips in thebase. A screwdriver may be necessary.
How to get the best coolingperformance
Place the cooler with its back near to anopen window or door so it can draw in100% fresh air.
Open another window or door on theopposite side of the room for “flowthrough” ventilation. This cooler will notcool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12Filling with water
Turn the cooler off before filling. Open thewater filling door and pour in clean water(Fig 12).
The water capacity is 14 litres. Theminimum amount of water needed for thepump to operate is 2 litres.
The cooler is full when the water levelindicator is in the “FULL” position(Fig 13).
! The cooler and pump will not bedamaged if operated without water.
Do not overfill, as water willspill out of the cooler!
Note
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.
5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,it should be filled with water and the coolknob turned to the “COOL” position (Fig 14).
(1) is selected for quietestoperation (Fig 14).
(3) is for maximum cooling(Fig 15).
. This cooler may beused as a fan only. Set the cool knob toposition “0” (Fig 15).
Low fan speed
High fan speed
Fan only (ventilation)
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen coolingpad
To get the best performance from your cooler,we recommend that when first used it is runwith water for at least 10 minutes at thesetting in Fig 16.
During this process the water becomesslightly yellow, and there is a natural smell ofdamp wood. This is normal.
Air direction control -Millenia / Mastercool
The cooler is provided with air guide vaneswhich can be adjusted as required to directthe air flow.
Models Millenia and Mastercool are adjustedmanually by sliding the levers on the frontpanel (Fig 17).
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17
4
®
Millenia series Portable Evaporative Cooler
Model Mastercool only
Place the reservoir onto the base andpress down to engage the four clips in thebase (Fig 10).
To remove the cooler from the base, tip itupside down and release the clips in thebase. A screwdriver may be necessary.
How to get the best coolingperformance
Place the cooler with its back near to anopen window or door so it can draw in100% fresh air.
Open another window or door on theopposite side of the room for “flowthrough” ventilation. This cooler will notcool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12Filling with water
Turn the cooler off before filling. Open thewater filling door and pour in clean water(Fig 12).
The water capacity is 14 litres. Theminimum amount of water needed for thepump to operate is 2 litres.
The cooler is full when the water levelindicator is in the “FULL” position(Fig 13).
! The cooler and pump will not bedamaged if operated without water.
Do not overfill, as water willspill out of the cooler!
Note
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.
5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,it should be filled with water and the coolknob turned to the “COOL” position (Fig 14).
(1) is selected for quietestoperation (Fig 14).
(3) is for maximum cooling(Fig 15).
. This cooler may beused as a fan only. Set the cool knob toposition “0” (Fig 15).
Low fan speed
High fan speed
Fan only (ventilation)
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen coolingpad
To get the best performance from your cooler,we recommend that when first used it is runwith water for at least 10 minutes at thesetting in Fig 16.
During this process the water becomesslightly yellow, and there is a natural smell ofdamp wood. This is normal.
Air direction control -Millenia / Mastercool
The cooler is provided with air guide vaneswhich can be adjusted as required to directthe air flow.
Models Millenia and Mastercool are adjustedmanually by sliding the levers on the frontpanel (Fig 17).
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17
6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Model Megacool has motor driven vanesthat are switched on and off by the fancontrol switch on the control panel (Fig18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes(shown). Set to “fan” speed settings forfixed direction.There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off andremove the electrical plug beforecleaning and servicing thecooler.
To clean, wipe the cooler with a dampcloth and a little household detergent.
The rear panel can be removed to gainaccess to inside the cooler by removingthe screws at the top of each side.
Pivot the panel backwards and lift off(Fig 20).
ILL880-B
20
Safety instruction
As this cooler contains water, ensure it ismoved carefully and is not tilted, as watermay spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont. MAINTENANCE cont.
End of Season
At least once a year at the end of summer itis advisable to do some simple maintenanceon your cooler to maintain its high efficiency.This involves cleaning the water system andthe Aspen cooling pad.
To drain water
Drain the water from the cooler by moving thecooler to a drain and removing the drain pluglocated on the bottom of the tank. When thecooler is empty replace the plug in the tank(Fig 21).
ILL879-A
21
AB A
ILL882-B
22Pump belt replacement
If a pump drive belt needs replacing, accesscan be gained by using a tool (screwdriver) toremove the small access door (Fig 22 - “A”).
Each cooler is supplied with a spare drainplug, located in the position shown (Fig 22 -“B”).
Spare drain plug
Water strainer and aspen cooling pad
Clean the water strainer by removing anyforeign matter. Wash the Aspen cooling padwith water while it is still in the rear panel.Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL
6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Model Megacool has motor driven vanesthat are switched on and off by the fancontrol switch on the control panel (Fig18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes(shown). Set to “fan” speed settings forfixed direction.There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off andremove the electrical plug beforecleaning and servicing thecooler.
To clean, wipe the cooler with a dampcloth and a little household detergent.
The rear panel can be removed to gainaccess to inside the cooler by removingthe screws at the top of each side.
Pivot the panel backwards and lift off(Fig 20).
ILL880-B
20
Safety instruction
As this cooler contains water, ensure it ismoved carefully and is not tilted, as watermay spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont. MAINTENANCE cont.
End of Season
At least once a year at the end of summer itis advisable to do some simple maintenanceon your cooler to maintain its high efficiency.This involves cleaning the water system andthe Aspen cooling pad.
To drain water
Drain the water from the cooler by moving thecooler to a drain and removing the drain pluglocated on the bottom of the tank. When thecooler is empty replace the plug in the tank(Fig 21).
ILL879-A
21
AB A
ILL882-B
22Pump belt replacement
If a pump drive belt needs replacing, accesscan be gained by using a tool (screwdriver) toremove the small access door (Fig 22 - “A”).
Each cooler is supplied with a spare drainplug, located in the position shown (Fig 22 -“B”).
Spare drain plug
Water strainer and aspen cooling pad
Clean the water strainer by removing anyforeign matter. Wash the Aspen cooling padwith water while it is still in the rear panel.Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL
8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not runningfast enough on low speed.
3.7 Pump drive belt faultyor broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motorreaches normal operating temperature. Allow the cooler torun for 30-60 minutes and check again. If there is noimprovement have the cooler checked by a service agent.
3.7.1 Replace drive belt as shown on page 7.
4.1 Reservoir or Aspencooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If itstill smells clean the reservoir and replace the Aspen coolingpad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes badsmell.
5.1 Dirt has accumulatedinside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makesscraping or rattlingnoise on new seasonstart up.
6.1 Too much water inreservoir.
6.2 Water level indicatornot working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicatorup to the 'FULL' position then let it drop. If it fails to operatehave it checked by a service agent.
6. Water overflows fromreservoir.
7.1 Electrical fault. 7.1.1 Electrical parts must only be repaired and replaced byAuthorised Service Agents.
7. Cooler will notoperate at all.
8.1.1 If the power supply cord of this appliance is damaged itmust be replaced. Electrical parts must only be repaired andreplaced by Authorised Service Agents.
8. Damaged powersupply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty ornearly empty.
3.3 Weather is too humid.
3.4 Aspen cooling pad and/ or pump inlet screenblocked or dirty.
3.5 Pump is not workingproperly.
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It isconnected to the fan motor and is driven mechanically. Turnthe cooler off and completely drain the reservoir. Refill withwater. Switch fan knob to high speed (3), turn the cool knobto 'COOL',run the cooler for 10-15 minutes non-stop. This willhelp dissolve and flush out the dirt. The Aspen cooling padshould now be wet. If the pad is not visibly wet and there isno cooling, have the cooler checked by a service agent.
1. Cooler will notoperate at first.
2. Cooler stopsoperating after runningfor some time.
1.1 Power outlet or supplyfaulty.
1.2 Wrong voltage.
2.1 Motor overheated(safety cutout).
1.1.1 Switch on power outlet.1.1.2 Check power supply.1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified onthe rating label.
2.1.1 Wait 30-45 minutes for motor to cool down and it willrestart automatically. If condition persists take the cooler to aservice agent.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial numberand colour of your cooler.
SPARE PARTS LIST
Item
Descri
pti
on
1Tank (
inclu
des d
rain
plu
g)
2D
rain
Plu
g
3R
ear
Panel
4F
ilter
Pad
5F
ront G
rille
Assem
bly
6B
adge -
Fro
nt G
rille
7W
indow
8F
iller
Door
9M
id P
anelA
ssem
bly
10
Inner
Grille
/ S
pre
ader
Assem
bly
11
Inner
Grille
Door
12
Scre
ws
13
Fro
nt / R
ear
Pill
ar
(pair)
14
Base
14.1
Base -
com
pact
15
Casto
r &
Pin
tle
Assem
bly
16
Contr
ol P
anel
17
Contr
ol B
ox
18
18.1
Knob M
ushro
om
Knob M
ushro
om
& S
haft
Assem
bly
19
Wate
r V
alv
eA
ssem
bly
20
20.1
Sw
itch (
2006 -
) M
illenia
/ M
aste
rcool
Sw
itch (
2006 -
) M
egacool
22
Lever
Vane
23
Vane L
ink R
H
24
Vane L
ink L
H
25
Vane
26
Vane B
earing
27
Vane L
ink M
oto
r
(Mill
enia
/ M
egacool)
(Mill
enia
/ M
egacool only
)
(Maste
rcool only
)
Item
Descri
pti
on
28
Pad C
lam
p
29
Wate
r Level In
dic
ato
r
30
Flo
atA
ssem
bly
31
Pum
pA
ssem
bly
32
Str
ain
er
33
Vane M
oto
r
34
Vane M
oto
r H
ub
36
Fan P
ulle
y
37
Fan
38
Drive B
elt
39
Spre
ader
Hose
Æ9.5
x 4
50
41
Pum
p H
ose
Æ9.5
x 8
90
42
42.1
Moto
r R
ubbers
White for
Square
Moto
r
Moto
r R
ubbers
Bla
ck for
Round M
oto
r
43.1
43
Ele
ctr
ic M
oto
r 230V
50H
z -
Round
Ele
ctr
ic M
oto
r 230V
50H
z -
Square
44
Capacitor
3.2
uf fo
r M
oto
r
46
Plu
g &
Cord
Austr
alia
47
Cord
Grip -
Fla
t C
ord
4K
-1
(Megacool only
)
(Megacool only
)
8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not runningfast enough on low speed.
3.7 Pump drive belt faultyor broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motorreaches normal operating temperature. Allow the cooler torun for 30-60 minutes and check again. If there is noimprovement have the cooler checked by a service agent.
3.7.1 Replace drive belt as shown on page 7.
4.1 Reservoir or Aspencooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If itstill smells clean the reservoir and replace the Aspen coolingpad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes badsmell.
5.1 Dirt has accumulatedinside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makesscraping or rattlingnoise on new seasonstart up.
6.1 Too much water inreservoir.
6.2 Water level indicatornot working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicatorup to the 'FULL' position then let it drop. If it fails to operatehave it checked by a service agent.
6. Water overflows fromreservoir.
7.1 Electrical fault. 7.1.1 Electrical parts must only be repaired and replaced byAuthorised Service Agents.
7. Cooler will notoperate at all.
8.1.1 If the power supply cord of this appliance is damaged itmust be replaced. Electrical parts must only be repaired andreplaced by Authorised Service Agents.
8. Damaged powersupply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty ornearly empty.
3.3 Weather is too humid.
3.4 Aspen cooling pad and/ or pump inlet screenblocked or dirty.
3.5 Pump is not workingproperly.
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It isconnected to the fan motor and is driven mechanically. Turnthe cooler off and completely drain the reservoir. Refill withwater. Switch fan knob to high speed (3), turn the cool knobto 'COOL',run the cooler for 10-15 minutes non-stop. This willhelp dissolve and flush out the dirt. The Aspen cooling padshould now be wet. If the pad is not visibly wet and there isno cooling, have the cooler checked by a service agent.
1. Cooler will notoperate at first.
2. Cooler stopsoperating after runningfor some time.
1.1 Power outlet or supplyfaulty.
1.2 Wrong voltage.
2.1 Motor overheated(safety cutout).
1.1.1 Switch on power outlet.1.1.2 Check power supply.1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified onthe rating label.
2.1.1 Wait 30-45 minutes for motor to cool down and it willrestart automatically. If condition persists take the cooler to aservice agent.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial numberand colour of your cooler.
SPARE PARTS LIST
Item
Descri
pti
on
1Tank (
inclu
des d
rain
plu
g)
2D
rain
Plu
g
3R
ear
Panel
4F
ilter
Pad
5F
ront G
rille
Assem
bly
6B
adge -
Fro
nt G
rille
7W
indow
8F
iller
Door
9M
id P
anelA
ssem
bly
10
Inner
Grille
/ S
pre
ader
Assem
bly
11
Inner
Grille
Door
12
Scre
ws
13
Fro
nt / R
ear
Pill
ar
(pair)
14
Base
14.1
Base -
com
pact
15
Casto
r &
Pin
tle
Assem
bly
16
Contr
ol P
anel
17
Contr
ol B
ox
18
18.1
Knob M
ushro
om
Knob M
ushro
om
& S
haft
Assem
bly
19
Wate
r V
alv
eA
ssem
bly
20
20.1
Sw
itch (
2006 -
) M
illenia
/ M
aste
rcool
Sw
itch (
2006 -
) M
egacool
22
Lever
Vane
23
Vane L
ink R
H
24
Vane L
ink L
H
25
Vane
26
Vane B
earing
27
Vane L
ink M
oto
r
(Mill
enia
/ M
egacool)
(Mill
enia
/ M
egacool only
)
(Maste
rcool only
)
Item
Descri
pti
on
28
Pad C
lam
p
29
Wate
r Level In
dic
ato
r
30
Flo
atA
ssem
bly
31
Pum
pA
ssem
bly
32
Str
ain
er
33
Vane M
oto
r
34
Vane M
oto
r H
ub
36
Fan P
ulle
y
37
Fan
38
Drive B
elt
39
Spre
ader
Hose
Æ9.5
x 4
50
41
Pum
p H
ose
Æ9.5
x 8
90
42
42.1
Moto
r R
ubbers
White for
Square
Moto
r
Moto
r R
ubbers
Bla
ck for
Round M
oto
r
43.1
43
Ele
ctr
ic M
oto
r 230V
50H
z -
Round
Ele
ctr
ic M
oto
r 230V
50H
z -
Square
44
Capacitor
3.2
uf fo
r M
oto
r
46
Plu
g &
Cord
Austr
alia
47
Cord
Grip -
Fla
t C
ord
4K
-1
(Megacool only
)
(Megacool only
)
10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
72
93
01
2
52
62
52
44
13
91
918
.11
81
62
04
41
74
34
23
64
31
011
38
93
23
13
7
14
13
15
23
27
33
34
46
47
12
28
Mill
en
iaM
eg
aco
ol
Ma
ste
rco
ol
8
22
61
2
ILL1432-A 0609
EXPLODED VIEW
11SEELEY INTERNATIONAL – OWNER’S MANUAL
In this warranty:
or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact detailsare set out at the end of this warranty;
means you, the original end-user purchaser of the Goods;
means the authorised distributor or retailer of the Goods that sold you the Goodsin Australia; and
means the product, unit, appliance or equipment which was accompanied by thiswarranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian ConsumerLaw. You are entitled to a replacement or refund for a major failure and for compensationfor any other reasonably foreseeable loss or damage. You are also entitled to have theGoods repaired or replaced if the Goods fail to be of acceptable quality and the failuredoes not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian ConsumerLaw or any other law, subject to the terms of this warranty, We provide the followingwarranty:
1. If, during the first 24 months from the date of first retail purchase ( ),the Goods upon examination prove defective by reason of improper workmanship ormaterial, We will repair at our nearest service centre or replace (at our option), theproduct or any part thereof without charge. Should we deem in our absolute discretionto replace the Goods, we may substitute any similar good even if it is not on our currentprice/equipment list. Further, Goods presented for repair may be replaced byrefurbished goods of the same type rather than being repaired. Refurbished parts maybe used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause 1 if the Goodshave not been used only for personal, domestic or household purposes or have notbeen operated and maintained in accordance with the instructions in the Owner'sManual. The addition of any third party device or the removal or the alteration of any ofour components will void this warranty. In addition, the warranty granted under clause 1does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to misuse of the cooler,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care andspecial provisions in the instructions.
3. The warranty granted under clause 1 is limited to repair or replacement only. As far asthe law permits, We will not be liable for any consequential loss suffered through, orresulting from, the non operation, or ineffective operation of the Goods. The warrantygranted under clause 1 does not cover damage to the Goods or other loss resultingfrom acts of God.
We
You
Supplier
Goods
Warranty Period
WARRANTY
10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
72
93
01
2
52
62
52
44
13
91
918
.11
81
62
04
41
74
34
23
64
31
011
38
93
23
13
7
14
13
15
23
27
33
34
46
47
12
28
Mill
en
iaM
eg
aco
ol
Ma
ste
rco
ol
8
22
61
2
ILL1432-A 0609
EXPLODED VIEW
11SEELEY INTERNATIONAL – OWNER’S MANUAL
In this warranty:
or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact detailsare set out at the end of this warranty;
means you, the original end-user purchaser of the Goods;
means the authorised distributor or retailer of the Goods that sold you the Goodsin Australia; and
means the product, unit, appliance or equipment which was accompanied by thiswarranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian ConsumerLaw. You are entitled to a replacement or refund for a major failure and for compensationfor any other reasonably foreseeable loss or damage. You are also entitled to have theGoods repaired or replaced if the Goods fail to be of acceptable quality and the failuredoes not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian ConsumerLaw or any other law, subject to the terms of this warranty, We provide the followingwarranty:
1. If, during the first 24 months from the date of first retail purchase ( ),the Goods upon examination prove defective by reason of improper workmanship ormaterial, We will repair at our nearest service centre or replace (at our option), theproduct or any part thereof without charge. Should we deem in our absolute discretionto replace the Goods, we may substitute any similar good even if it is not on our currentprice/equipment list. Further, Goods presented for repair may be replaced byrefurbished goods of the same type rather than being repaired. Refurbished parts maybe used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause 1 if the Goodshave not been used only for personal, domestic or household purposes or have notbeen operated and maintained in accordance with the instructions in the Owner'sManual. The addition of any third party device or the removal or the alteration of any ofour components will void this warranty. In addition, the warranty granted under clause 1does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to misuse of the cooler,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care andspecial provisions in the instructions.
3. The warranty granted under clause 1 is limited to repair or replacement only. As far asthe law permits, We will not be liable for any consequential loss suffered through, orresulting from, the non operation, or ineffective operation of the Goods. The warrantygranted under clause 1 does not cover damage to the Goods or other loss resultingfrom acts of God.
We
You
Supplier
Goods
Warranty Period
WARRANTY
SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY cont.
4. We are not responsible in any way for any failure and/or inadequate performance of theGoods which arises from or is connected to the use in the Goods of non-genuine spareparts. We strongly recommend that only spare parts supplied or approved by us areused in the Goods.
5. No other person, firm or corporation is authorised by us to offer or give on our behalfany other or greater warranty than that given under this warranty. The benefitsconferred by this warranty are in favour of You and any person deriving title to theGoods through or under such person and are intended to be separate from andadditional to all other rights and remedies that they may have in law in respect of theGoods.
6. In order to claim under the warranty granted under clause 1 you must:
(a) either:
(i) contact us within the Warranty Period on: ;
or
(ii) log a claim on our website www.seeleyinternational.com within the WarrantyPeriod; and
(b) return the Goods to your nearest service centre (or to us at the address below) byprepaid freight within the Warranty Period, together with (i) the legible andunmodified proof of purchase, which clearly indicates the name and address of theoriginal retailer, the date and place of purchase, the product name or other productserial number, and (ii) a copy of the completed Warranty Information page below.(If you choose to return the Goods to us, there is an additional requirement - theywill also need to be accompanied by a covering letter which states your name andaddress and daytime telephone number, and the model and serial number of thegoods.)
7. This warranty does not cover the cost of claiming under the warranty, it is yourresponsibility to cover all forwarding and return freight costs incurred in sending theGoods to and from your nearest service centre or us.
8. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to theextent that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired forpersonal, domestic or household use or consumption, your remedies associated with anyfailure or defect of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
and subject to the terms and conditions included in this warranty.
1300 650 644
12
®
Millenia series Portable Evaporative Cooler
WARRANTY cont.
To ensure that service either pursuant to the above warranty or otherwise is readilyavailable, we have established in all States authorised service centres, which are availableto deal with service requirements.
For further information about your nearest service centre and other enquiries please callour Service Centre on:
Complete the following for your records:
:
: ...................................................................
...................................................................
...................................................................
: ....../....../......
1300 650 644
Please retain your receipt as proof of purchase. Every request for warranty must beaccompanied by proof of purchase.
:
Serial Number:
Product
Model
Purchased from
Date purchased
Convair
Mastercool MIC Millenia MIMegacool MIV1 1
1
Service Department
Seeley International Pty Ltd
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com
SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY cont.
4. We are not responsible in any way for any failure and/or inadequate performance of theGoods which arises from or is connected to the use in the Goods of non-genuine spareparts. We strongly recommend that only spare parts supplied or approved by us areused in the Goods.
5. No other person, firm or corporation is authorised by us to offer or give on our behalfany other or greater warranty than that given under this warranty. The benefitsconferred by this warranty are in favour of You and any person deriving title to theGoods through or under such person and are intended to be separate from andadditional to all other rights and remedies that they may have in law in respect of theGoods.
6. In order to claim under the warranty granted under clause 1 you must:
(a) either:
(i) contact us within the Warranty Period on: ;
or
(ii) log a claim on our website www.seeleyinternational.com within the WarrantyPeriod; and
(b) return the Goods to your nearest service centre (or to us at the address below) byprepaid freight within the Warranty Period, together with (i) the legible andunmodified proof of purchase, which clearly indicates the name and address of theoriginal retailer, the date and place of purchase, the product name or other productserial number, and (ii) a copy of the completed Warranty Information page below.(If you choose to return the Goods to us, there is an additional requirement - theywill also need to be accompanied by a covering letter which states your name andaddress and daytime telephone number, and the model and serial number of thegoods.)
7. This warranty does not cover the cost of claiming under the warranty, it is yourresponsibility to cover all forwarding and return freight costs incurred in sending theGoods to and from your nearest service centre or us.
8. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to theextent that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired forpersonal, domestic or household use or consumption, your remedies associated with anyfailure or defect of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
and subject to the terms and conditions included in this warranty.
1300 650 644
12
®
Millenia series Portable Evaporative Cooler
WARRANTY cont.
To ensure that service either pursuant to the above warranty or otherwise is readilyavailable, we have established in all States authorised service centres, which are availableto deal with service requirements.
For further information about your nearest service centre and other enquiries please callour Service Centre on:
Complete the following for your records:
:
: ...................................................................
...................................................................
...................................................................
: ....../....../......
1300 650 644
Please retain your receipt as proof of purchase. Every request for warranty must beaccompanied by proof of purchase.
:
Serial Number:
Product
Model
Purchased from
Date purchased
Convair
Mastercool MIC Millenia MIMegacool MIV1 1
1
Service Department
Seeley International Pty Ltd
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com
829524-D convair.net.au AU 1112
Warranty Service
Australia 1-300-650-644seeleyinternational.com
It is the policy of Seeley International to introduce continualproduct improvement. Accordingly, specifications are
subject to change without notice. Please consult with yourdealer to confirm the specifications of the model selected.
®
