RM Classboard TouchWith Bluetooth Connectivity

PolyVision Interactive White BoardWorks with the following computer configurations:

MacPC with Built in BluetoothPC with no built in Bluetooth

Main benefits of the Bluetooth White Board:

No cable required to connect the board to the computer.

Caring for your PolyVision BoardDO NOT UNDER ANY CIRCUMSTANCES

USE DRY ERASE CLEANER ON THE BOARD’S SURFACE.

The board is cleaned by using soap and water mixture.

If you write on the board use only dry erase markers and clean the board that day to insure you board will last.

The board has a five year warranty from RM.

Powering the PolyVision Board

Installing the Bluetooth

Installing the RM Classboard Bluetooth

The RM installers should have connected this during installation.

Bluetooth is held in place by two screws.

Loading the PolyVision SoftwareYou must have administrative rights to load the software.

Use the Polyvision disk that comes in the Polyvision box orUse the Polyvision software from the Web Sitehttp://www.polyvision.com/Support/Downloads/tabid/232/CategoryId/18/DownloadTypeId/106/LangId/158/Default.aspx

Choose Mac or PC

Downloading the Polyvsion Drivers

Downloading the PolyVision DriversOnce drivers have been loaded, turn off the computer completely.

Leave computer shut down for two minutes. Insert the Polyvision Bluetooth into one of your

computer’s USB ports.Turn on computer with Bluetooth inserted in

the USB port.

Stop and Read Below:If you have a PC, please continue to the next slide for directions on whiteboard connectivity. If you have a MAC please continue to the NEXT Stop Sign in this presentation for connecting using your MAC computer.

Required Bluetooth Setting on LaptopsOn the “Start” toolbar bar, chose the Control Panel.

Once in Control Panel, chose Administrative Tools.

Required Bluetooth Setting on Laptops

Choose Services Shortcut.

Required Bluetooth Setting on Laptops

Select Bluetooth Support Services.

Required Bluetooth Setting on Laptops

On the General tab, hit the stop button.

Required Bluetooth Setting on LaptopsMove to the Log On Tab, make sure to chose LOCAL SYSTEM ACCOUNT.

Go back to the General Tab and hit the START button.

Connecting to the POLYVISION Adapter to the Classboard Bluetooth- PC DirectionsNow that you the Classboard drivers dowloaded, you are

ready to connect the board with your computer. Give your computer a chance to recognize the Polyvision bluetooth. You will see this icon pop up in the system tray.

Step 1:

Right click on the Bluetooth icon in the system tray on your desktop.

Step 2: A similar menu will pop up, please select Add Bluetooth Device.

Connecting to the POLYVISION Adapter- PC Directions

Select the device is ready to be setup and hit the NEXT button.

Step 3: This screen will appear, follow directions below:

Connecting to the POLYVISION Adapter- PC Directions

Step 4: Choose the PV device and follow directions below:

Select and hit the next button

Connecting to the POLYVISION Adapter- PC Directions

Step 5: Select the Use Passkey found in documentation and type in the passcode 1,2,3,4 and hit next.

Hit next after entering code.

Passcode is 1, 2, 3,4

Connecting to the POLYVISION Adapter- PC Directions

Step 6: The computer will connect to the RM Classboard Bluetooth.

Connecting to the POLYVISION Adapter- PC DirectionsFinal Step: Your Bluetooth is now configured and ready to be used.

Click on the finish button.

Configuring the POLYVISION Driver- PC Directions

Step 1: Click on the Polyvision board short cut and choose the “Configure Polyvision Driver tab.”

RM Classboard Configuration Preferences- PC Directions

Short-cut to the board drivercan be found on the desktop to access the configuration. Click to launch configuration options.

Choose the “best” selection on the “projection” tab. This will give you the best calibration.

Connecting to the POLYVISION Adapter to the Classboard Bluetooth- PC Directions

Final step is to connect the whiteboard by clicking the “find serial whiteboard button.”

Once the board is connected you will hear the board “chirp.”

Now hit the projector button on the board short cuts and this will take you to the calibration screen.

Connecting the POLYVISION Adapter to the IWB Bluetooth- PC Directions

After you go through the previous steps one time, you

should automatically connect to the board as long as

your Polyvision Bluetooth Adapter is inserted in your

computer…every time you turn on the board, it will

automatically connect with the “chirp.”

Then you hit the projection button and the board is ready

to use.

Calibrating the PolyVision Boards Hit the projection short cut button on the board this green calibration screen will pop up. Hit each target toensure perfect calibration.

Main Short Cut Tools on the RM Classboard

More Tools Continued…