Comparative Simulation of the Purification of Wet …...Phosphoric Acid (WPA) with fairly good...
Transcript of Comparative Simulation of the Purification of Wet …...Phosphoric Acid (WPA) with fairly good...
Volume 3 • Issue 2 • 1000134J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
Research Article Open Access
Hamdi and Hannachi, J Chem Eng Process Technol 2012, 3:2 DOI: 10.4172/2157-7048.1000134
Rapid Communication Open Access
Comparative Simulation of the Purification of Wet Phosphoric Acid by Tbp, Mibk and a Mixture (MIBK+TBP)R. Hamdi* and A. Hannachi
Department of Chemical-Process Engineering, National Engineering School of Gabes, Omar Ibn El Khattab St., 6029 Zrig, Gabes, Tunisia
*Corresponding author: Rania Hamdi, Department of Chemical-Process Engineering, National Engineering School of Gabes, Omar Ibnelkhattab St., 6029 Zrig, Gabes, Tunisia, E-mail: [email protected]
Received April 21, 2012; Accepted April 25, 2012; Published April 26, 2012
Citation: Hamdi R, Hannachi A (2012) Comparative Simulation of the Purification of Wet Phosphoric Acid by Tbp, Mibk and a Mixture (MIBK+TBP). J Chem Eng Process Technol 3:134. doi:10.4172/2157-7048.1000134
Copyright: © 2012 Hamdi R, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.
AbstractLiquid-liquid solvent extraction technology is used in several industrial processes such as petrochemical
processing, pharmaceutical production, food and hydrometallurgy. It is successfully applied for the purification of Wet Phosphoric Acid (WPA) with fairly good purification performances. The purification process is basically carried out in three steps: extraction, washing and recovery, each of these steps is a liquid-liquid extraction operation. The aim was to develop a computer code that helps predicting the overall performance of the purification process for a given set of operating conditions. The adopted approach is based on determining the necessary theoretical stages for each step in the purification process using a numerical technique. Some simulation results for the WPA purification process with Tri-Butyl Phosphate (TBP) at 45°C, Methyl Isobutyl Ketone (MIBK) at 25°C and a mixture (MIBK+TBP) at 30°C are presented.
Keywords: Wet process phosphoric acid; Purification; Solventextraction; Simulation; NTS
IntroductionThe most commonly used process for the production of phosphoric
acid is: thermal and wet-process. The thermal process produces a pure acid with huge energy consumption. The wet-process involves reaction of phosphate rock with an acid (mainly sulfuric acid). This process is economic and practiced everywhere in the world [1,2]. Phosphoric acid produced by the latter process contains a variety of impurities, which vary according to the origin of the minerals. These impurities are removed from the acid by several techniques such as precipitation, adsorption, ion exchange and solvent extraction [1-12].
Liquid-liquid extraction is at the heart of many WPA purification processes. Several solvents can be used for the purification of WPA. The majority of solvents are able to extract selectively phosphoric acid (H3PO4), indeed alcohols, the etheroxydes, the ketones like Methyl Isobutyl Ketone (MIBK) and the phosphoric esters as Tributyle phosphates (TBP). The purification process is basically carried out in three steps: extraction, washing and recovery. All of these three steps are liquid-liquid extraction operations. Because of the complexity of such operations, it is very difficult to predict the overall performance of the purification process for a given set of operating conditions, making it very hard to find the optimal conditions for conducting the purification process [8-12].
On the basis of experiment undertaken to a scale laboratory, this study proposes to exploit the equilibriums isotherms to develop a computer code for the simulation of the operation of purification of WPA. The considered solvent is Methyl Isobutyl Ketone (MIBK).
The objective of this work is then to unfold a method for predicting the overall performance of the purification process by solvent extraction. This technique is founded on the simulation of the WPA purification process. The adopted approach is based on the determination of the necessary theoretical stages for each step in the purification process using a numerical technique. Some simulation results of a WPA purification process will be shown.
Modelling of the WPA purification
The modeling of the WPA purification was limited to three
consecutive operations: extraction, washing and stripping, in order to simulate the purification of WPA by solvents with TPB, MIBK and mixtures MIBK+TBP. In this study, each step of the purification process is assumed to be conduct in a cascade of counter current theoretical stages. The phase diagram of the ternary system H3PO4 – water – considered solvents and the portion ratios for some traceimpurities for the three systems have to be approximated. For the threesolvents TBP, MIBK and mixtures MIBK+TBP, a representative H3PO4distribution between the organic and the aqueous phases is shownrespectively in Figure 1, 2 and 3. Also, the partition ratios for sometrace impurities as function of the acid concentration in the organicphase are shown in Figure 4, 5 and 6.
For a given feed quality and an acid extraction rate in the extraction phase, the number of theoretical stages is determined as follows (Figure 7):
Extract
Equilibrium
Raffinate
100%
80%
60%
40%
20%
0%0% 20% 40% 60% 80%
Acid weight fraction (%)
TBP/
cold
wei
ght f
ract
ion
(%)
Figure 1: Equilibrium isotherms (H3PO4-H2O-TBP at 45°C).
Journal of Chemical Engineering & Process TechnologyJournal
of C
hem
ical E
ngineering & Process Technology
ISSN: 2157-7048
Page 2 of 2
Citation: Hamdi R, Hannachi A (2012) Comparative Simulation of the Purification of Wet Phosphoric Acid by Tbp, Mibk and a Mixture (MIBK+TBP). J Chem Eng Process Technol 3:134. doi:10.4172/2157-7048.1000134
Volume 3 • Issue 2 • 1000134J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
i. Assuming the raffinate quality and performing an overall balance yields the acid composition in the extract;
ii. The acid composition in the aqueous phase leaving the first stage is determined from the equilibrium curve;
iii. An overall balance between the second and the last stage yields the acid composition in the extra phase leaving the second stage and from the acid distribution isotherm the acid composition in the raffinate phase exiting the same stage;
iv. This calculation procedure is repeated until the last stage for which inlet extract phase and the outlet raffinate compositions should be consistent with the assumed extraction rate and the solvent composition. If these conditions are not satisfied, the solvent rate has to be modified and the calculation procedure has to be repeated until satisfaction of the convergence criteria.
This calculation procedure gives also the acid contents in all fluxes. A similar iterative numerical technique can be also applied to
obtain impurities’ contents in every flux. These iterative computation techniques have been implemented in a computer code that is capable of finding the number of theoretical stages as well as the composition of all fluxes in each step of the purification process.
Results and DiscussionThe Number of Theoretical Stages’ (NTS) is an important parameter
for the dimensioning of the equipments used in the purification process. A large NTS is equivalent of a difficult operation that needs huge equipments to insure adequate mass transfer between phases. For the three considered solvents, the NTS required for extracting a given amount of the acid in feed at 78% H3PO4 weight fraction for a residual content equal to 45% in H3PO4. For the same solvent rate, the operation of extraction with TPB at 45°C and mixtures MIBK+TBP require the same NTS, however MIBK the operation of extraction requires a NTS more important than foe the other solvent.
For a given amount of acid extracted by the solvent, the computer code gives the acid as well as impurities’ weight fractions in all streams
100%
80%
60%
40%
20%
0%0% 20% 40% 60% 80%
Acid weight fraction (%)
MB
K/c
old
wei
ght f
ract
ion
(%)
Extract
Equilibrium
Raffinate
Figure 2: Equilibrium isotherms (H3PO4-H2O-MIBK at 25°C).
100%
80%
60%
40%
20%
0%
0% 20% 40% 60% 80%
Acid weight fraction (%)
TBP
+ H
IBK
/aci
d w
eigh
t fra
ctio
n (%
)
Extract
Equilibrium
Raffinate
Figure 3: Equilibrium isotherms (H3PO4-H2O- TBP+MIBK at 30°C).
15
10
5
012% 13% 14% 15% 16% 17%
Solvent acid weight fraction, Y (%)
Par
tion
ratio
x 1
03(-
)
SO4
Fe
AlMg
Figure 4: Some impurities’ partition ratios (TBP at 45°C).
Fe
AlMg
SO4
Part
ion
ratio
x 1
03(-)
Solvent acid weight fraction, Y (%)
12 22 32
200
160
120
80
40
0
Figure 5: Some impurities’ partition ratios (MIBK+TBP at 30°C).
10
8
6
4
2
00 2 4
Taux de solvant, τ (-)No
mbr
e dl
etag
es th
eoriq
ues,
NET
TBP (45˚C)
MIBK (25˚C)
MIBK+TBP(30˚C)
X F= 0 .78X R= 0 .45
Figure 6: Number of theoretical stages for extracting H3PO4 from the WPA versus the solvent rate.
1
0,8
0,6
0,4
0,2
00 1 2 3 4 5
Etages theoriques
Con
cen
trat
ion
en H
3P
O4,
x, y
xH3PO4, TBP
xH3PO4, (MIBK+TBP)
yH3PO4, (MIBK+TBP)
yH3PO4, TBP
Figure 7: Raffinate and extract acid contents along the ideal extractors.
Page 3 of 2
Citation: Hamdi R, Hannachi A (2012) Comparative Simulation of the Purification of Wet Phosphoric Acid by Tbp, Mibk and a Mixture (MIBK+TBP). J Chem Eng Process Technol 3:134. doi:10.4172/2157-7048.1000134
Volume 3 • Issue 2 • 1000134J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
flowing in out of all theoretical stages in the extraction operation. As an example, for an operation that requires five stages, Figures 8, 9 and 10 give details of the composition of the acid and impurities in both phases at each stage, for the three solvents, for a WPA at 78% H3PO4 with a fixed H3PO4 extraction rate at 82%. These details provide valuable information on the intensity of solute transfer taking place in each stage. It is clear from these figures that much of the transfer is happening in the stages close to the fresh solvent feed.
For the same operating conditions and for various solvent rates, the computed impurities’ extraction rates for the TPB at 45°C, MIBK at 25°C and mixtures MIBK+TBP at 30°C are given respectively in Figure 11,12 and 13. As expected because of the increase of the required NTS, the extraction rate for the undesired matter intensifies when the solvent rate decreases. Comparison to other solvents, TBP at 45°C presents the best performances as for the reduction of the metallic impurities’ content. The classification by descending order of the extraction rates of the impurities for the TBP is as follows: Mg, Al, Fe and SO4.
The comparison between the experimental results obtained with various solvent rates for the operations of extraction with those provided by the developed code is necessary to valid our approach. Figure 14 and 15 give the extract impurities content obtained by the computer code, according to the experimental results of analysis of the impurities in the extract. It’s noticed that the point are close to the first bisector, with those experimental with a light over-estimate for the TBP. For sulphates and iron, the error is higher because of the equilibrium isotherms Figure 16.
The extract exiting the first step in the H3PO4 purification process is then washed with pure water. This treatment is indented to eliminate the undesired impurities in the extract. The same numerical procedure as for the extraction, the result of the washing operation can also be
200
150
100
50
0
20000
15000
10000
5000
00 1 2 3 4 5 6
Stage number
Extr
act I
mpu
ritie
s co
nten
ts (p
pm)
Raf
finat
e Im
purit
ies
cont
ents
(ppm
)SO4
Al
Fe
Mg
Figure 8: Raffinate and extract impurities’ contents along the ideal extractors for TBP.
2500
2000
1500
1000
500
0
19000
16000
13000
10000
7000
4000
10000 1 2
com
posi
tion
des
impu
rete
s da
ns le
raffi
nat (
ppm
)
Com
posi
tion
des
impu
rete
s da
ns l’
extr
ait (
ppm
)
Etages theoriques
SO4
Fe
Mg
Al
Figure 9: Raffinate and extract impurities’ contents along the ideal extractors for MIBK.
Mg Fe Al
Com
posi
tion
des
impu
rete
s da
ns l’
extra
it (p
pm)
Com
posi
tion
des
impu
rete
s da
ns le
raffi
nat (
ppm
)
19000
16000
13000
10000
7000
4000
1000
Etages theoriques
0 1 2 3 4 5
Figure 10: Raffinate and extract impurities’ contents along the ideal extractors for MIBK+TBP.
30
20
10
01 2 3 4 5
SO4
Fe
Mg
Al
Solvent rates, τ (-)
Impu
ritei
s ex
tract
ion
rate
(%)
Figure 11: Purified acid impurities’ contents versus acid content of the stripped solvent (TBP).
Solvent rates, τ (-)
0 1 2 3 4 5
30
20
10
0
Impu
rite
isex
trac
tio
n r
ate
(%)
Mg
Fe
Al
xF
xR
=0,78=0,4
Figure 12: Purified acid impurities’ contents versus acid content of the stripped solvent (MIBK+TBP).
xFxR
=0,78=0,4
SO4
Mg
FeImpu
ritei
s ex
trac
tion
rate
(%)
Solvent rates, τ (-)0 1 2 3
60
40
20
0
Figure 13: Purified acid impurities’ contents versus acid content of the stripped solvent.
SO4 Mg Fe Al
Concentrations des impuretes dansl’extrait (ppm)
Est
imat
ion
des
conc
entr
atio
ns d
esim
pura
tes
dans
l’ex
trai
t (pp
m)
80
60
40
20
00 20 40 60 80
Figure 14: Comparison between the experimental results and theoretical results.
Page 4 of 2
Citation: Hamdi R, Hannachi A (2012) Comparative Simulation of the Purification of Wet Phosphoric Acid by Tbp, Mibk and a Mixture (MIBK+TBP). J Chem Eng Process Technol 3:134. doi:10.4172/2157-7048.1000134
Volume 3 • Issue 2 • 1000134J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
ConclusionIn this study, a simulation of the purification of Wet Phosphoric
Acid (WPA) was developed. The purification is based on solvent extraction. The computer code is applied for the extraction, washing and stripping the WPA. These operations are carried out in a cascade of counter current theoretical stages with three solvents witch knowing: Tri-Butyl Phosphate (TBP), Methyl Isobutyl Ketone (MIBK) and mixture (MIBK+TBP). The adopted approach is based on determining the necessary theoretical stages and the content of acid and impurities in the two phases for each step in the purification process. This approach could be used as a tool for predicting the WPA purification results in order to look for the optimal operating condition to conduct this operation.
References
1. Cuer JP, Floreancig (1980) ‘Nouvelle source d’acide phosphorique très pur, procédé double solvant’, Proceedings of the 2nd international congress on phosphorous compounds. Boston, USA 529-540.
2. Hignett TP (1980) Production of wet process phosphoric acid. Proceedings of the 2nd international congress on phosphorous compounds. Boston, USA 401-429.
3. Leenaerts R (1984) Purification de l’acide phosphorique de voie humide. Bull séance Acad r Sci Outre-Mer 28: 529-545.
4. Davister A, Peeterbroeck M (1982) The prayon for wet process phosphoric acid purification. CEP, Mars 35-39.
5. Ruiz F, Marcilia A, Ancheta M, Caro JA (1985) Purification of Wet Process Phosphoric Acid by Solvent Extraction with Isoamyl Alcohol. Part II. Study of the Impurities Distribution. Solvent Extraction and Ion Exchange 3: 345-355.
6. Hanna AA, Youssef NS, Ali AF (1995) Purification of wet process phosphoric acid by solvent extraction. Egypt. 38: 311-317.
7. Feki M, Ayedi HF (2000) Modélisation du traitement de purification de l’acide phosphorique de voie humide par la méthylisobutylcétone. Can J Chem Eng 78: 540-546.
8. Hannachi A, Ben Zaied T, Ouederni A, et Chtara C (2002) Simulation de l’opération de purification de l’acide phosphorique industriel par extraction. Proceedings of the 4th J TET, Hammamet, Tunisie 2: 101-106.
9. Hannachi A, Hamdi R, Abbas N, Chtara C, RATEL A (2006) Simulation of the wet process phosphoric acid purification process by solvent extraction. Proceedings of the COVAPHOS II 3: 251-260.
10. Hamdi R, khleifia N, Tlili N, Hannachi A (2009) Prediction of the concentration profiles along a continuous liquid-liquid extraction column for phosphoric acid purification. The First International Chemical and Process Engineering, Tripoli.
11. Khleifia N, Hamdi R, Hannachi A (2010) Etude de l’extraction de l’acide phosphorique industriel dans une colonne. Continue, Proceedings of the 7th J.T.E.T, Tunisia.
12. Hamdi R, Hannachi A, Chtara C, Ratel A (2009) Impact du Prétraitement de l’acide phosphorique industriel sur l’opération d’extraction de H3PO4 par un solvant organique. Proceedings of the COVAPHOS III, Maroc.
predicted. For an extract feeding the washing operation at 31% H3PO4 and a fixed acid weight fraction of the washed extract at 25%, Figure 17 gives the amount of the considered impurities discharged with the washing water and their concentration levels in the cleaned extract. As expected, the impurities extraction rate in decreasing order is for Mg, Al, Fe and SO4. The sulphates removal rates for the washing operation is important because the extract in feed is rich in sulphates. By comparing the numerical result with those experimental in Figure 18 witches shows a good agreement.
The washed extract is then feeding the stripping operation in order to re-extract the acid to obtain the final purified phosphoric acid. The last one will undergo a post treatment process. A similar approach that applied for the extraction and washing can be used for the stripping operation. For a washed extract 25% H3PO4 supplying the stripping operation and for three acid concentration levels of the purified acid, the concentration of some trace impurities for the TPB at 45°C, MIBK at 25°C and mixtures MIBK+TBP at 30°C. For three acid concentrations, the ratio of the impurities’ content in the purified acid, rapporting at 78% H3PO4, with the acid feeding the first step of extraction shows that for the TBP, as an example, Aluminum content in the purified acid are lower than 0.1% of those in the feeding acid. It is clear that one has to find the optimum stripping rate that leads to high acid concentration with minimum impurities contents in the purified acid.
100
80
60
40
20
0
SO4 Mg Fe Al
Impu
ritei
s’ re
mov
al (
%) TBP MIBK MIBK+TBP
Figure 15: Impurities’ removal rates for the washing operation.
SO4 Mg Fe Al
60
40
20
00 20 40 60
Concentrations des impuretes dansl’extrait
Estim
atio
n de
s co
ncen
trat
ions
des
impu
rate
s da
ns l’
extr
ait
Figure 16: Comparison between the experimental results and theoretical results.
xr=0,15xr=0,1xr=0,05
SO4 Mg Fe Al
60
40
20
0
Purif
ied
acid
con
cent
ratio
nle
vels
Figure 17: Purified acid impurities’ contents versus acid content of the stripped solvent.
TBP (45˚C)
(M IBK+TBP)(30˚C)
MIBK (25˚C)
xr= 0,15 xr=0,1 xr=0,05
2
1
0
XX
Al,
recu
pA
l,F(%
)/
Figure 18: Ratio between Purified acid impurities’ contents and feeding acid versus acid content of the stripped solvent.