CNC Vise PIP - Chick WorkholdingOF REV Product Information Packet One-Lok™ Single Station CNC Vise...
4
REV OF Product Information Packet One-Lok™ Single Station CNC Vise CNC Vise PIP 1/21/2009 1 4 (800) 332-4425 (724) 772-1644 www.ChickWorkholding.com PATENT PENDING Product Information Packet The One-Lok™ Single Station CNC Vise
Transcript of CNC Vise PIP - Chick WorkholdingOF REV Product Information Packet One-Lok™ Single Station CNC Vise...
REVOF
Product Information Packet
One-Lok™ Single Station CNC Vise
CNC Vise PIP1/21/2009
1 4
(800) 332-4425
(724) 772-1644
www.ChickWorkholding.com
PATENT PENDING
Product Information Packet
The One-Lok™
Single Station CNC Vise
REVOF
Product Information Packet
One-Lok™ Single Station CNC Vise
CNC Vise PIP1/21/2009
2 4
(800) 332-4425
(724) 772-1644
www.ChickWorkholding.com
PATENT PENDING
6mm T-Wrench*
12mm Swivel Wrench*
Toe Clamps (set of 4)*(005-0254)
CNC Vise Workstop(CWS1510)
CNC Vise Foundation LocatingStops (CLS0030)
CNC Vise OutBoardHard Jaw Plate Set(CHJ1506)
BoltFast Standard SoftJaw Set (CBFSJ-150-50)
CNC Vise LocatingKeys - 5/8" (CLK0625)
CNC Vise Locating Keys- Blank (CLKBLNK)
Items with an asterisk (*) are included withOne-Lok™ Single Station CNC Vise (COL1520)
One-Lok™*
BoltFast Plain Hard Jaw Set*(CBFHJ-150)
BoltFast Bolt-on Jaw Spacer Set(CBFSP-150)
BoltFast Stepped Hard Jaw Set (CBFST-150-06)
REVOF
Product Information Packet
One-Lok™ Single Station CNC Vise
CNC Vise PIP1/21/2009
3 4
(800) 332-4425
(724) 772-1644
www.ChickWorkholding.com
PATENT PENDING
5.98 in [152 mm]Jaw Width
4.72 in [120 mm]Base Width
0.83 in [21 mm]0.83 in [21 mm]
8 in [203.2 mm]
Holding Capacity
3.58 in [91 mm]3.94 in [100 mm]
3.94 in [100 mm]
17.01 in [432 mm]
0.94 in [23.88 mm]
3.88 in [98.43 mm]
1/2-13 UNC x 1 in [25 mm]
Note: This hole pattern is on the front and rear
of both movable and fixed jaws
Fixed JawMovable Jaw
6mm Hex
12mm Hex
8.51 in [216.2 mm]
1.97 in [50 mm]
REVOF
Product Information Packet
One-Lok™ Single Station CNC Vise
CNC Vise PIP1/21/2009
4 4
(800) 332-4425
(724) 772-1644
www.ChickWorkholding.com
PATENT PENDING
3.62 in [92 mm]
15.75 in [400 mm]
3.48 in [88.47 mm]
4.92 in [125 mm]
6x n12.03 mm [0.622 in]
x8.25 mm
Holes labeled "X" are
for use with CNC Vise
locating keys
11.81 in [300 mm]
X
X
X
X
X
X
Y
Y
Holes labeled "Y" are for usewhen installing onto Chick
5-1040 system
Bottom view of One-Lok™
3.58 in [91 mm]
BoltFast Standard Soft Jaws
3.39 in [86mm]
1.5 in [38mm]
5.98 in [152mm]
1.91 in [48.5mm]
0.67 in [17mm]
1.46 in [36mm]
non-machinable area representedby gray hatched region
