CLEAVER INSTRUCTION MANUAL - Baltic Networks · Cleaver Body Allen Wrench (1.5mm) Instruction...
2
1. Open up the cover and set t he jacket-removed fiber on the cleaving spot. Then, check on t he fiber if it is properly set agai nst the scale mark. 2. Close the holder cover. 3. Close the cover and check on the fiber end if it is placed straight over the clamp. Then, cut the fiber by moving the slider forward. 4. Open up the cover and check on the fiber. 5. Strip the fiber and keep it clean from dust or foreign material. 6. Remove fiber ends with a tweezer for the next step and be careful with fiber and blade from damaging your hands. Standard package/Accessories. Cleaver Body Allen Wrench (1.5mm) Instruction Manual Fiber Holder ( For Single Fiber Only) Chip Collector (CI-02) Storage Pouch/Case • Read this instruction manual carefully before using the cleaver and keep it along with its product. For the safety of user, please be careful with the following; <Safety Instruction> 1. COMPONENTS OF CLEAVER CI-01,CF-01A CI-02 CI-03A CI-03B, CF-03A,CS-03A - Store the cleaver away from moisture. - Keeping the cleaver near damp or dusty areas might cause problems. - Use and store cleavers at room temperature, deformation by heat expected otherwise. - Vibration or external shock applied to the cleaver may cause damage to the cleaver. - When exchanging the holder for the ribbon fiber, make sure the bolts are completely fasten with proper tool. - When cleaving optical fiber, make sure the stripped length is at least longer than 12mm(16mm for CI-08). - Do not use organic solvent like acetone, but alcohol to rubber parts. 2. FLOW OF CUTTING FIBERS CI-01, CF-01A CI-02 CI-03A CI-03B, CF-03A, CS-03A 1. Open up the cover and set the jacket-re moved fiber on the cleaving spot. Then, che ck on the fiber if it is properly set against th e scale mark. 2. Cut the fiber by pressing on the cover. 3. Strip the fiber and keep it clean from dus t or foreign material. 4. Move fiber ends to the waste bin with a t weezer for the next step and be careful wit h fiber and blade from damaging your hand s. 1. Open up the cover and set the jacket-re moved fiber on the cleaving spot. Then, che ck on the fiber if it is properly set against th e scale mark. 2. Cut the fiber by pressing on the cover. 3. Open up the cover and check on the fiber. 4. Remove fiber ends with a tweezer for the next step and be careful with fiber and blade from damaging your hands. 1. Open up the cover and set the jacket- removed fiber on the cleaving spot. Then, check on the fiber if it is properly set against the scale mark. 2. Cut the fiber by pressing on the cover. 3. Open up the cover and check on the fiber. 4. Strip the fiber and keep it clean from dus t or foreign material. Fiber ends are automa tically removed by the chip box ass’y. CLEAVER INSTRUCTION MANUAL
Transcript of CLEAVER INSTRUCTION MANUAL - Baltic Networks · Cleaver Body Allen Wrench (1.5mm) Instruction...
1. Open up the cover and set the jacket-removed fiber on the cleaving spot. Then, check on the fiber if it is properly set against the scale mark.
2. Close the holder cover.
3. Close the cover and check on the fiber end if it is placed straight over the clamp. Then, cut the fiber by moving the slider forward.
4. Open up the cover and check on the fiber.
5. Strip the fiber and keep it clean from dust or foreign material.
6. Remove fiber ends with a tweezer for the next step and be careful with fiber and blade from damaging your hands.
Standard package/Accessories.Cleaver Body Allen Wrench (1.5mm) Instruction Manual
Fiber Holder ( For Single Fiber Only) Chip Collector (CI-02) Storage Pouch/Case
• Read this instruction manual carefully before using the cleaver and keep it along with its product. For the safety of user, please be careful with the following;
<Safety Instruction>
1. COMPONENTS OF CLEAVER
CI-01,CF-01A CI-02 CI-03A CI-03B, CF-03A,CS-03A
- Store the cleaver away from moisture.
- Keeping the cleaver near damp or dusty areas might cause problems.
- Use and store cleavers at room temperature, deformation by heat expected otherwise.
- Vibration or external shock applied to the cleaver may cause damage to the cleaver.
- When exchanging the holder for the ribbon fiber, make sure the bolts are completely fasten with proper tool.
- When cleaving optical fiber, make sure the stripped length is at least longer than 12mm(16mm for CI-08).
- Do not use organic solvent like acetone, but alcohol to rubber parts.
2. FLOW OF CUTTING FIBERS
CI-01, CF-01A CI-02 CI-03A CI-03B, CF-03A, CS-03A
1. Open up the cover and set the jacket-removed fiber on the cleaving spot. Then, check on the fiber if it is properly set against the scale mark.
2. Cut the fiber by pressing on the cover.
3. Strip the fiber and keep it clean from dust or foreign material.
4. Move fiber ends to the waste bin with a tweezer for the next step and be careful with fiber and blade from damaging your hands.
1. Open up the cover and set the jacket-removed fiber on the cleaving spot. Then, check on the fiber if it is properly set against the scale mark.
2. Cut the fiber by pressing on the cover.
3. Open up the cover and check on the fiber.
4. Remove fiber ends with a tweezer for the next step and be careful with fiber and blade from damaging your hands.
1. Open up the cover and set the jacket-removed fiber on the cleaving spot. Then, check on the fiber if it is properly set against the scale mark.
2. Cut the fiber by pressing on the cover.
3. Open up the cover and check on the fiber.
4. Strip the fiber and keep it clean from dust or foreign material. Fiber ends are automatically removed by the chip box ass’y.
CLEAVERINSTRUCTION MANUAL
3. ADJUSTMENT OF BLADES (POSITION CHANGES)
CI-01, CF-01A CI-02 CI-03A CI-03B, CF-03A, CS-03A
1. Open the cover as shown in the figure and hold the slider by hand.
2. Deal with a wrench that belongs to the cleaver on its bottom surface.
3. Loosen the set screw as well as it’s on enough.(approximately 2 rounds)
4. Using a swab, turn the scale counterclockwise to increase the scale number of the blades. Blades are fixed in reverse order.
1. The blade has 16 positions inscribed on the side of the blade.2. When it doesn’t work properly, wipe with a wet cotton swab against the side of the blade and rubber parts.
(Do not ever use organic solvent like acetone, etc. but alcohol to rubber parts)3. There is a continuous problem in terms of cutting means the blade is out. Therefore, either change another channel or replace for new one.
3-1. FLOW OF CHANGING THE CUTTING POSITIONS
1. Following on the picture, hold the body andloosen the setscrew properly (about 2 turns)with A wrench.
2. Loosen the setscrew enough (about 2 turns)with wrench on the bottom surface. And theslider should position pulled back in themeantime.
3. Screw the wrench bolt from the bottom surface into the blade pin to pull it out of the slider with tool like A tweezer.
4. Carefully replace the other blade as shown.Be careful not to damage the blade. Assembly isdone in reverse order of disassembly. Tighten the setscrew firmly.
3-2. FLOW OF REPLACING FOR NEW BLADES
1. Open the cover as shown in the figure and hold the slider by hand.
2. Deal with a wrench that belongs to the cleaver on its bottom surface.
3. Loosen the set screw as well as it’s on enough.(approximately 2 rounds)
4. Using a swab, turn the scale counterclockwise to increase the scale number of the blades. Blades are fixed in reverse order..
1. Open the cover as shown in the figure and hold the slider by hand.
2. Deal with a wrench that belongs to the cleaver on its bottom surface.
3. Loosen the set screw as well as it’s on enough.(approximately 2 rounds)
4. Using a swab, turn the scale counterclockwise to increase the scale number of the blades. Blades are fixed in reverse order..
1. Open the cover as shown in the figure and hold the slider by hand.
2. Deal with a wrench that belongs to the cleaver on its bottom surface.
3. Loosen the set screw as well as it’s on enough.(approximately 2 rounds)
4. Using a swab, turn the scale counterclockwise to increase the scale number of the blades. Blades are fixed in reverse order.
CI-01, CF-01A CI-02 CI-03A CI-03B, CF-03A, CS-03A
This instruction may be changed without notice. Further details can be found in the website or the customer service center.Maintenance : [email protected]
1. Following on the picture, hold the body andloosen the setscrew properly (about 2 turns)with A wrench.
2. Loosen the setscrew enough (about 2 turns)with wrench on the bottom surface. And theslider should position pulled back in themeantime.
3. Screw the wrench bolt from the bottom surface into the blade pin to pull it out of the slider with tool like A tweezer.
4. Carefully replace the other blade as shown.Be careful not to damage the blade. Assembly isdone in reverse order of disassembly. Tighten the setscrew firmly.
1. Following on the picture, hold the body andloosen the setscrew properly (about 2 turns)with A wrench.
2. Loosen the setscrew enough (about 2 turns)with wrench on the bottom surface. And theslider should position pulled back in themeantime.
3. Screw the wrench bolt from the bottom surface into the blade pin to pull it out of the slider with tool like A tweezer.
4. Carefully replace the other blade as shown.Be careful not to damage the blade. Assembly isdone in reverse order of disassembly. Tighten the setscrew firmly.
1. Following on the picture, hold the body andloosen the setscrew properly (about 2 turns)with A wrench.
2. Loosen the setscrew enough (about 2 turns)with wrench on the bottom surface. And theslider should position pulled back in themeantime.
3. Screw the wrench bolt from the bottom surface into the blade pin to pull it out of the slider with tool like A tweezer.
4. Carefully replace the other blade as shown.Be careful not to damage the blade. Assembly isdone in reverse order of disassembly. Tighten the setscrew firmly.
CLEAVER INSTRUCTION MANUALWWW.UCLSWIFT.COM
