CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS 2015-6-9Fundamentals of Photonics 1 Chapter 5 Photons in...
-
Upload
brianne-bradley -
Category
Documents
-
view
224 -
download
4
Transcript of CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS 2015-6-9Fundamentals of Photonics 1 Chapter 5 Photons in...
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 1
Chapter 5Photons in Semiconductors
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 2
Semiconductors
• A semiconductor is a solid material that has electrical conductivity in between a conductor and an insulator.
• Semiconductors can be used as optical detectors, sources (light-emitting diodes and lasers), amplifiers, waveguides, modulators, sensors, and nonlinear optical elements.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 3
A. Energy bands and A. Energy bands and charge carrierscharge carriers
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 4
Energy bands in semiconductors
• The solution of the Schrödinger equation for the electron energy in the periodic potential created by the atoms in a crystal lattice, results in a splitting of the atomic energy levels and the formation of energy bands.
ATOMSOLID
E2’
E1’
Conduction band
Valence band
E21
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 5
Energy bands in semiconductors
• Each band contains a large number of finely separated discrete energy levels that can be approximated as a continuum.
• The valence and conduction bands are separated by a “forbidden” energy gap of width Eg bandgap energy
Conduction band
Valence band
BandgapE
Unfilled bands
Filled bands
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 6
Energy bands in semiconductors
Materials with a large energy gap (>3eV) are insulators, those for which the gap is small or nonexistent are conductors, semiconductors have gaps roughly in the range 0.1 to 3 eV
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 7
ev
1.1ev
Si
Conduction band
Valence band
En
ergy
5
-10
0
-15
-5
ev
1.42ev
GaAs
Conduction band
Valence band
En
ergy
5
-10
0
-15
-5
EgEg
(a) (b)
Figure 15.1-1 Energy bands: (a) in Si, and (b) in GaAs
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 8
Electrons and holes
• In the absence of thermal excitations, the valence band is completely filled and the conduction band is completely empty. Thus, the material cannot conduct electricity.
• As the temperature increases, some electrons will be thermally exited into the empty conduction band, result in the creation of a free electron in the conduction band and a free hole in the valence band.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 9
Bandgap energy Eg
Conduction band
Valence band
Electron Hole
Ele
ctro
n e
ner
gy
E
Figure 15.1-2 Electrons in the conduction band and holes in the valence band at T>0.
Electrons and holes
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 10
Energy-momentum relations
2 2 2
0 02 2
p kE
m m
pk
p is the magnitude of the momentum
k is the magnitude of the wavevector associated with the electron’s wavefunction
m0 is the electron mass
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 11
K
K
[100][111]
[100][111]
E
E
Si
GaAs
Figure 15.1-3 Cross section of the E-K function for Si and GaAs along the crystal directions [111] and [100].
Eg=1.1ev
Eg=1.42ev
The energy of an electron in the conduction band depends not only on the magnitude of its momentum, but also on the direction in which it is traveling in the crystal
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 12
Effective mass
Near the bottom of the conduction band, the E-k relation may be approximated by the parabola
2 2
2cc
kE E
m
2 2
2vv
kE E
m
Ec,Ev: the energy at the bottom of the conduction band and at the top of the valence band
mc,mv: effective mass of the electron in the conduction band and the hole in the valence band
The effective mass depends on the crystal orientation and the particular band under consideration
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 13
Typical ratios of the average effective masses to the mass of the free electron mass
mc/m0 mv/m0
Si 0.33 0.5
GaAs 0.07 0.5
Effective mass
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 14
Direct- and indirect-gap semiconductors
K
K
[100][111]
[100][111]
E
E
Si
GaAs
Figure 15.1-4 Approximating the E-K diagram at the bottom of the conduction band and at the top of the valence band of Si and GaAs by parabols.
Eg=1.1ev
Eg=1.42ev
The direct-gap semiconductors such as GaAs are efficient photon emitters, while the indirect-gap counterparts are not.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 15
B. Semiconducting B. Semiconducting materialsmaterials
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 16
Semiconducting materials
• Si: widely used for making photon detectors but not useful for fabricating photon emitters due to its indirect bandgap.
• GaAs, InP GaN etc.: used for making photon detectors and sources.
• Ternary and quaternary semiconductors: AlxGa1-xAs, InxGa1-xAsyP1-y etc.
tunable bandgap energy with variation of x and y.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 17
Semiconducting materials
AlxGa1-xAs is lattice matched to GaAs, means it can be grown on the GaAs without introducing strains.
Solid and dashed curves represent direct-gap and indirect-gap compositions respectively.
We can see that a material may have direct bandgap for one mixing ratio x and an indirect bandgap for a different x.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 18
Doped semiconductors
• Dopants: alter the concentration of mobile charge carriers by many orders of magnitude.
• n-type: predominance of mobile electrons
• p-type: predominance of holes
n p
p n
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 19
C. Electron and hole C. Electron and hole concentrationsconcentrations
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 20
Density of states
The density of states describes the number of states at each energy level that are available to be occupied.
3/ 21/ 2
2 3
(2 )( ) ( ) ,
2c
c c c
mE E E E E
3/ 21/ 2
2 3
(2 )( ) ( ) ,
2v
v v c
mE E E E E
Density of states near band edges
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 21
K
Ec
Ef
Eg
E
Ec
Ef Ef
Ec
E
Density of states
c(E)
v(E)
(a) (b) (c)
Figure 15.1-7 (a) Cross section of the E-K diagram (e.g., in the direction of the K1 component with K2 and K3 fixed). (b) Allowed energy levels (at all K). (c) Density of states near the edges of the conduction and valence bands. Pc(E)dE is the number of quantum states of energy between E and E+dE, per unit volume, in the conduction band. P(E) has an analogous interpretation for the valence band.
E
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 22
Probability of occupancy
Under the condition of thermal equilibrium, the probability that a given state of energy E is occupied by an electron is determined by the Fermi function.
1( )
exp[( ) / ] 1f B
f EE E k T
Ef: Fermi level, the energy level for which the probability of occupancy is 1/2.
f(E) is not itself a probability distribution, and it does not integrate to unity; rather it is a sequence of occupation probabilities of successive energy levels.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 23
Figure 15.1-8 The Fermi function f(E) is the probability that an energy level E is filled with an electron; 1-f(E) is the probability that it is empty. In the valence band, 1-f(E) is the probability that energy level E is occupied by a hole. At T=0K, f(E)=1 for E<Ef, and f(E)=0 for E>Ef, i.e., there are no elctrons in the conduction band and no holes in the valence band.
Ec
Ef
Ev
Eg
T>0K T=0K
Ec
Ef
Ev
Ec
Ef
Ev
f(E)
f(E)
0 1 10 0.50.5
f(E)
1-f(E)
EE
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 24
Figure 15.1-10 Energy-band diagram, Fermi function f(E), and concentrations of mobile electrons and holes n(E) and p(E) in an n-type semiconductor.
E ED
Ec
Ev
f(E)
Carrier concentration
0 1
EE
Donor level Ef
n(E)
p(E)
The Fermi level is above the middle of the bandgap
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 25
Figure 15.1-11 Energy-band diagram, Fermi function f(E), and concentrations of mobile electrons and holes n(E) and p(E) in an p-type semiconductor
E
EA
Ec
Ev
f(E)
Carrier concentration
0 1
EE
Acceptor levelEf
n(E)
p(E)
The Fermi level is below the middle of the bandgap
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 26
Exponential approximation of the Fermi function
( ) ( ) ( )cn E E f E ( ) ( )[1 ( )]vp E E f E
( )cE
n n E dE
When the Fermi level lies within the bandgap, but away from its edges by an energy of at least several times , the equations above gives:
exp( )c fc
B
E En N
k T
exp( )f v
vB
E Ep N
k T
exp( )g
c vB
Enp N N
k T
2 3/ 22(2 / )c c BN m k T h2 3/ 22(2 / )v v BN m k T h
As Nc and Nv are
( )vE
p p E dE
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 27
Law of mass action
3 3/ 22
2exp( ) 4( ) ( ) exp( )g gB
c v c vB B
E Ek Tnp N N m m
k T h k T
is independent of the location of the Fermi level
Thus in p n for intrinsic semiconductor
We have 1/ 2( ) exp( )gi c v
B
En N N
k T
The law of mass action is useful for determining the concentrations of electrons and holes in doped semiconductors.
Therefore the law of mass action can be written as:
2inp n
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 28
D. Generation, D. Generation, recombination, and injectionrecombination, and injection
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 29
Generation and recombination in thermal equilibrium
Thermal equilibrium requires that the process of generation of electron-hole pairs must be accompanied by a simultaneous reverse process of deexcitation,.
The electron-hole recombination, ooocurs when an electron decays from the conduction band to fill a hole in the valence band.
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 30
Radiative recombination: the energy released take the form of an emitted photon.Nonradiative recombination: transfer of the energy to lattice vibrations or to another free electron.
Recombination may also occur indirectly via traps or defect centers, they can act as a recombination center if it is capable of trapping both the electron and the hole, thereby increasing their probability of recombining.
rate of combination= npε(cm3/s) a parameter that depends on the characteristics of the material
Generation and recombination in thermal equilibrium
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 31
Electron-hole injection
Define G0 as the rate of recombination at a given temperature:
0 0 0=G n p
Now let additional electron-hole pairs be generated at a steady rate R
A new steady state: 0 0,n n n p p p
We get: R=n
With 0 0
1
[( ) ]n p n
τ: the electron-hole recombination lifetime
0 +R=G np As
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 32
Electron-hole injection
For an injection rate such that 0 0n n p
0 0
1
( )n p
In a n-type material, where n0>>p0,the recombination lifetime τ≈1/εno is inversely proportional to the electron concentration.
Similarly, for p-type material, τ≈1/εp0.
This simple formulation is not applicable when traps play an important role in the process.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 33
Internal quantum efficiency
The internal quantum efficiency ηi is defined as the ratio of the radiative electron-hole recombination rate to the total recombination.
It determines the efficiency of light generation in a semiconductor material.
nrr ri
r nr r r nr
For low to moderate injection rates, 0 0
1
( )rr n p
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 34
Internal quantum efficiency
ε r
(cm3/s)τr τnr τ ηi
Si 10-15 10ms 100ns 100ns 10-5
GaAs 10-30 100ns 100ns 50ns 0.5
The radiative lifetime for Si is orders of magnitude larger than its overall lifetime, mainly due to its indirect bandgap, result in a small internal quantum efficiency
On the other hand, direct bandgap material as GaAs, the decay is largely via radiative transitions, consequently larger internal quantum efficiency, useful for fabricating light-emitting devices.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 35
E. JunctionsE. Junctions
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 36
• Homojunctions: junctions between differently doped reguions of a semiconductor material
• Heterojunctions: junctions between different semiconductor materials
The p-n junctionThe p-n junction
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 37
Figure 15.1-15 Energy levels and carrier concentrations of a p-type and n-type semiconductor before contact.
Ef
Ef
Ele
ctro
n
ener
gy
Car
rier
co
nce
ntr
atio
n
P
P
n
n
P-type n-type
position
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 38
Figure 15.1-16 A p-n junction in thermal equilibrium at T>0K. The depletion-layer, energy-band diagram, and concentrations (on a logarithmic scale) of mobile electrons n(x) and holes p(x) are shown as functions of position x. The built-in potrntial difference V0 corresponds to an energy eV0, where e is the magnitude of the electron charge.
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 39
1. The depletion layer contains only the fixed charges, the thickness of the depletion layer in each region is inversely proportional to the concentration of dopants in the region.
2. The fixed charges created a built-in field obstructs the diffusion of further mobile carriers.
3. A net built-in potential difference V0 is established.
4. In thermal equilibrium there is only a single Fermi function for the entire structure so that the Fermi levels in the p- and n- regions must align.
5. No net current flows across the junction.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 40
Energy-band and carrier concentrations in a forward-biased p-n junction.
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 41
The biased junction
Forward biased
A misalignment of the Fermi levels in the p- and n-regions
Net current i=isexp(eV/kBT)-is
Reverse biased
Net current ≈-is as V is negative in exp(eV/kBT) and |V|>>kBT/e
[exp( ) 1]sB
eVi i
k T
Acts as a diode with a current-voltage characteristic
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 42
The p-i-n junction diode
• Made by inserting a layer of intrinsic (or lightly doped) semiconductor material between the p- and n-type region.
• The depletion layer penetrates deeply into the i-region.
• Large depletion layer: small junction capacitance thus fast response
• Favored over p-n diodes as photodiodes with better photodetection efficiency
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 43
The p-i-n junction diode
A p-i-n diode has the depletion layer penetrates deeply into the i-region
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 44
Heterojunctions
Junctions between different semiconductor materials are called heterojunctions.
P nP
Eg1 Eg2 Eg3
Electro
n en
ergy
They can provide substantial improvement in the performance of electronic and optoelectronic devices
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 45E
lectron
en
ergy
Ef
Eg1 Eg2 Eg3
Electro
n
energ
y
A potential energy discontinuity provides a barrier that can be useful in preventing selected charge carriers from entering regions where they are undesired.
This property used in a p-n junction can reduce the proportion of current carried by minority carriers, and thus to increase injection efficiency
Junctions between materials of different bandgap create localized jumps in the energy-band diagram
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 46
• Discontinuities in the energy-band diagram created by two heterojunctions can be useful for confining charge carriers to a desired region of space
• Heterojunctions are useful for creating energy-band discontinuities that accelerate carriers at specific locations
• Semiconductors of different bandgap type can be used in the same device to select regions of the structure where light is emitted and where light is absorbed
• Heterojunctions of materials with different refractive indices create optical waveguides that confine and direct photons.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 47
Quantum Wells and Super-lattices
• When the Heterostructures layer thickness is comparable to, or smaller than, the de Broglie wavelength of thermalized electrons (≈50 nm in GaAs), the energy-momentum relation for a bulk semiconductor material no longer applies.
• A quantum well is a double heterojunction structure consisting of an ultrathin (≤50 nm) layer of semiconductor material whose bandgap is smaller than that of the surrounding material.
• The sandwich forms conduction- and valence band rectangular potential wells within which electrons in the conduction-band well and holes in the valence-band well are confined.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 48
(a) Geometry of the quantum-well structure. (b) Energy-level diagram for electrons and holes in a quantum well. (c) Cross section of the E-k relation in the direction of k2 or k3. The energy subbands are labeled by their quantum number q1 = 1,2,... The E-k relation for bulk semiconductor is indicated by the dashed curves.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 49
The energy levels Eq in one-dimensional infinite rectangular well are determined by Schrodinger equation:
2 2( / ), 1, 2,....
2q
q dE q
m
The energy-momentum relation:
2 2
1 1, 1, 2,3,...,2c q
c
kE E E q
m
where k is the magnitude of a two-dimensional k = (k2, k3) vector in the y-z plane
For the quantum well, k1 takes on well-separated discrete values. As a result, the density of states associated with a quantum-well structure differs from that associated with bulk material.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 50
In a quantum-well structure the density of states is obtained from the magnitude of the two-dimensional wavevector (k2, k3)
121
1
,( )
0
............
................., ..
cc q
c
c q
mE E E
dE
E E E
1 1,2,...,q
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 51
quantum-well structure exhibits a substantial density of quantum-well structure exhibits a substantial density of states at its lowest allowed conduction-band energy level states at its lowest allowed conduction-band energy level and at its highest allowed valence-band energy leveland at its highest allowed valence-band energy level
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 52
Multiquantum Wells and Superlattices
Multiple-layered structures of different semiconductor materials that alternate with each other are called multiquantum-well (MQW) structures
A multiquantum-well structure fabricated from alternating layers of AlGaAs and GaAs
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 53
Quantum Wires and Quantum Dots
The density of states in different confinement configurations: (a) bulk; (b) quantum well; (c) quantum wire; (d) quantum dot. The conduction and valence bands split into overlapping subbands that become successively narrower as the electron motion is restricted in more dimensions.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 54
A semiconductor material that takes the form of a thin wire of rectangular cross section, surrounded by a material of wider
bandgap, is called a quantum-wire structure2 2
1 2 2c q qc
kE E E E
m
2 2 2 21 1 2 2
1 2 1 2
( / ) ( / ), , , 1, 2,...,
2 2q qc c
q d q dE E q q
m m
1/ 21 2
1 21/ 21 2
1 2
.....
..........................
(1/ )
........
( / 2 ),
( ) ( )
0,
, 1,2,...,
.....
.
cc q q
c c q q
d d mE E E E
E E E E E
otherwise
q q
Density of states
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 55
In a quantum-dot structure, the electrons are narrowly confined in all three directions within a box of volume d1d2d3.
1 2 3
2 21 1
1
2 22 2
2
2 23 3
3
1 2 3
( / ),
2
( / ),
2
( / )
2
, , 1, 2,...,
c q q q
qc
qc
qc
E E E E E
q dE
m
q dE
m
q dE
m
q q q
Quantum dots are often called artificial atoms.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 56
INTERACTIONS OF PHOTONS WITH
ELECTRONS AND HOLES
Chapter 15.2
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 57
Mechanisms leading to absorption and emission of photons in a semiconductor:
• Band-to-Band (Inter-band) Transitions.• Impurity-to-Band Transitions.• Free-Carrier (Intraband) Transitions• Phonon Transitions• Excitonic Transitions.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 58
Examples of absorption and emission of photons in a semiconductor. (a) Band-to-band transitions in GaAs can result in the absorption or emission of photons of wavelength . (b) The absorption of a photon of wavelength results in a valence-band to acceptor-level transition in Hg-doped Ge (Ge:Hg). (c) A free-carrier transition within the conduction band.
0 / 0.87g ghc E m
0 / 14A Ahc E m
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 59
Examples of absorption and emission of photons in a semiconductor. (a) Band-to-band transitions in GaAs can result in the absorption or emission of photons of wavelength . (b) The absorption of a photon of wavelength results in a valence-band to acceptor-level transition in Hg-doped Ge (Ge:Hg). (c) A free-carrier transition within the conduction band.
0 / 0.87g ghc E m
0 / 14A Ahc E m
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 60
Absorption coefficient for some semiconductor materials
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 61
Absorption coefficient for some semiconductor materials
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 62
• For photon energies greater than the bandgap energy Eg, the absorption is dominated by band-to-band transitions
• Absorption edge:
The spectral region where the material changes from being relatively transparent to strongly absorbing
• Direct-gap semiconductors have a more abrupt absorption edge than indirect-gap materials
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 63
Band-to-Band Absorption and Emission
Bandgap Wavelength:
1.24( )
( )gg
mE eV
The quantity g is also called the cutoff wavelength.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 64
Absorption and Emission
(a) The absorption of a photon results in the generation of an electron-hole pair. This process is used in the photodetection of light. (b) The recombination of an electron-hole pair results in the spontaneous emission of a photon. Light-emitting diodes (LEDs) operate on this basis. (c) Electron-hole recombination can be stimulated by a photon. The result is the induced emission of an identical photon. This is the underlying process responsible for the operation of semiconductor injection lasers.
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 65
Conditions for Absorption and Emission
• Conservation of Energy
• Conservation of Momentum
2 1E E h
2 1
2 1
....
....
/ /
/. 2
p p hv c h or
k k
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 66
Conditions for Absorption and Emission
• Energies and Momenta of the Electron and Hole with Which a Photon Interacts
2 ( )rc g
c
mE E h E
m
1 2( )rv g
v
mE E h E E h
m
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 67
Optical Joint Density of States
3/ 21/ 2
2
(2 )( ) ( ) ,r
g g
mh E h E
The density of states with which a photon of energy interacts under conditions of energy and momentum conservation in a direct-gap semiconductor is determined by:
( ) hv
The density of states with which a photon of energy interacts increases with in accordance with a square-root law
hvghv E
And illustrated as follow:
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 68
Photon Emission Is Unlikely in an Indirect-Gap Semiconductor !
Photon emission in an indirect-gap semiconductor
The recombination of an electron near the bottom of the conduction band with a hole near the top of the valence band requires the exchange of energy and momentum. The energy may be carried off by a photon, but one or more phonons are required to conserve momentum. This type of multiparticle interaction is unlikely.
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 69
Photon Absorption is Not Unlikely in an Indirect-Gap Semiconductor!
Photon absorption in an indirect-gap semiconductor
The photon generates an excited electron and a hole by a vertical transition; the carriers then undergo fast transitions to the bottom of the conduction band and top of the valence band, respectively, releasing their energy in the form of phonons. Since the process is sequential it is not unlikely.
点击查看 flash动画
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 70
Rates of Absorption and Emission
• Occupancy probabilitiesOccupancy probabilities
• Transition probabilitiesTransition probabilities
• Density of statesDensity of states
the probability densities of a photon of energy h being emitted or absorbed by a semiconductor material in a direct band-to-band transition are mainly determined by three factors:
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 71
Occupancy Probabilities
• Emission condition: A conduction-band state of energy E2 is filled (with an electron) and a valence-band state of energy E1 is empty (i.e., filled with a hole)
• Absorption condition: A conduction-band state of energy E2 is empty and a valence-band state of energy E1 is filled.
The probabilities are determined from the appropriate Fermi functions and associated with the conduction and valence bands of a semiconductor in quasi-equilibrium
( )cf E ( )vf E
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 72
2 1( ) ( )[1 ( )]e e vf f E f E
The probability that the emission condition is satisfied for a photon of energy is:
( )ef hv
The probability that the absorption condition is satisfied is :
( )af
2 1( ) [1 ( )] ( )a c vf f E f E
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 73
Transition Probabilities
• Satisfying the emission/absorption occupancy condition does not assure that the emission/absorption actually takes place.
• These processes are governed by the probabilistic laws of interaction between photons and atomic systems
Transition Cross Section:
2
( ) ( )8 r
g
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 74
Probability density for the spontaneous emission:
1( ) ( )sp
r
P d g d
Probability density for the stimulated emission:
2
( ) ( ) ( )8i v v
r
W d d g d
If the occupancy condition for absorption is satisfied, the probability density for the absorption is also fit this formula
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 75
Overall Emission and Absorption Transition
Rates of Spontaneous Emission 、 Stimulated Emission and Absorption:
1( ) ( ) ( )sp e
r
r f
2
( ) ( ) ( )8st v e
r
r f
2
( ) ( ) ( )8ab v a
r
r f
the occupancy probabilities and is determined by the quasi-Fermi levels Efc and Efv
( )ef v ( )af v
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 76
Spontaneous Emission Spectral Density in Thermal Equilibrium
A semiconductor in thermal equilibrium has only a single Fermi function so
2 1( ) ( )[1 ( )] exp( )eB
hf f E f E
k T
then
1/ 20( ) ( ) exp( ),g
sp g gB
h Er D h E h E
k T
where3/ 2
0 2
(2 )exp( )gr
r B
EmD
k T
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 77
Spectral density of the direct band-to-band spontaneous emission rate (photons per second per hertz per cm3) from a semiconductor in thermal equilibrium as a function of hv. The spectrum has a low-frequency cutoff at
and extends over a width of approximately .
( )spr v
/gv E h 2 /Bk T h
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 78
Gain Coefficient in Quasi-Equilibrium
The net gain coefficient is2
0 ( ) ( ) ( )8 g
r
f
Where the Fermi inversion factor is given by
2 1( ) ( ) ( ) ( ) ( )g e a c vf f f f E f E
The gain coefficient may be cast in the form:1/ 2
0 1( ) ( ) ( ),g g gD h E f h E
with3/ 2 2
1 2
2 r
r
mD
h
The sign and spectral form of the Fermi inversion factor are governed by the quasi-Fermi levels Efc and Efv, which, in turn, depend on the state of excitation of the carriers in the semiconductor.
( )gf v
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 79
Absorption Coefficient in Thermal Equilibrium
A semiconductor in thermal equilibrium has only a single Fermi level, so:
1( ) ( ) ( )
exp[( ) / ] 1c vf B
f E f E f EE E k T
Therefore the absorption coefficient:
1/ 21 1 2( ) ( ) [ ( ) ( )]gD h E f E f E
If Ef lies within the band gap but away from the band edges
2 3/ 21/ 2
2
2 1( ) ( )
( )r
gr
c mh E
h
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 80
The absorption coefficient resulting from direct band-to-band transitions as a function of the photon energy (eV) and wavelength for GaAs
1( )( )v cm
hv 0 ( )m
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 81
Refractive Index
• The ability to control the refractive index of a semi-conductor is important in the design of many photonic devices
• Semiconductor materials are dispersive the refractive index is dependent on the wavelength
• The refractive Index is related to the absorption coe-fficient inasmuch as the real and imaginary parts of the susceptibility must satisfy the Kramers-Kronig relations
• The refractive index also depends on temperature and on doping level
( )v
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 82
Refractive index for high-purity, p-type, and n-type GaAs at 300 K, as a function of photon energy (wavelength).
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
23/4/18Fundamentals of Photonics 83
Refractive Indices of Selected Semiconductor Materials at T = 300 K for Photon Energies Near the Bandgap Energy of the Material ghv E
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
Electron-hole generation 返回
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
Electron-hole Recombination via a trap 返回
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
p-n junction 返回
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
The Biased Junction 返回
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
Photon emission in an indirect-gap semicondutor返回
CHAPTER 5-1---PHOTONS IN SEMICONDUCTORS
Photon absorption in an indirect-gap semicondutor返回