CAUTION: Plastic PrimerGlue Flap 5/16" Back Panel Area 4 3/16" Wide Copy Area 3.625" Wide Front...
Transcript of CAUTION: Plastic PrimerGlue Flap 5/16" Back Panel Area 4 3/16" Wide Copy Area 3.625" Wide Front...
Glue Flap 5/16"
Back Panel Area 4 3/16" Wide
Copy Area 3.625" Wide
Front Panel Area 4" Wide
Copy Area 2.750" Wide
Designed, engineered and recommended by Ford Motor Company.
5.90
625
Inch
es T
all
DIRECTIONS FOR APPLICATIONNOTE: Apply only to those parts where Ford Motor Company specifi es product usage.
Surface Preparation: Thoroughly clean the surface to be primed. Remove all dirt, grease, moisture, etc., by wiping in one direction with a silicone and wax remover.
Product Application: PRIOR TO USE, SHAKE THE CONTAINER THOROUGHLY. Hold the can 8 –10 inches from the part, and with a steady back and forth motion, spray a full, wet coat. This is a clear primer; therefore, in order to be sure all areas of the parts surface are covered, check if there is a uniform gloss across the surface of the part while the primer is still wet. Flash dry, then apply a second wet coat. Flash dry for 2–3 minutes. Color coat as soon as possible after fl ash drying (preferably within 10 minutes) using Ford Interior Spray Lacquer or equivalent.
Cleaning: If the sprayhead becomes clogged, twist, and then pull upward. The entire sprayhead will lift out of the container. Use knife blade or similar object to remove any obstruction in the small slot in the intake stem of the sprayhead. Use a pin or fi ne wire to clear nozzle opening. If necessary, soak the sprayhead in lacquer thinner. After cleaning, immediately replace the sprayhead, keeping the nozzle pointed away from you and nearby objects. DO NOT REMOVE THE SPRAYHEAD EXCEPT FOR CLEANING.
CAUTION: Do not take internally. Avoid contact with eyes and skin. Do not inhale vapors or mists. Use only with adequate ventilation. Intentional misuse by deliberately concentrating or inhaling the contents can be harmful or fatal. While using this product, do not eat, drink, or smoke. Wash thoroughly after handling. Do not puncture or incinerate the container. Do not store above 110 °F. Keep away from heat, sparks, or fl ame. Store tightly closed in a cool, well-ventilated area away from sources of ignition.
Contains: Toluene (108-88-3); propane (74-98-6); butane (106-97-8); acetone (67-64-1); xylene (1330-20-7); ethylbenzene (100-41-4).
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
FIRST AID: In case of EYE CONTACT, immediately rinse eyes with plenty of water for at least 15 minutes and seek medical attention or advice. In case of SKIN CONTACT, fl ush with large amounts of water. Remove contaminated clothing and wash before reuse.If irritation persists, seek medical attention. If SWALLOWED immediately get medical attention or advice—DO NOT INDUCE VOMITING. If INHALED, immediately remove affected individual to fresh air. If symptoms develop or persist, seek medical attention.
KEEP OUT OF THE REACH OF CHILDRENFor additional information, see the Material Safety Data Sheet
(MSDS) for this product.
PM-9 � Ford Internal Reference Number 040057
For 24-hour MEDICAL EMERGENCY INFORMATION, CALL: 1-800-959-3673 (FORD)
DISTRIBUTED BY: FORD MOTOR COMPANYATTENTION: MSDS INFORMATION � P.O. BOX 1899, DEARBORN, MI 48121
PRINTED IN USA � ML1136 � © FORD MOTOR COMPANY
DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR. CONTENTS UNDER PRESSURE. HARMFUL OR FATAL IF SWALLOWED. VAPOR HARMFUL—MAY CAUSE IRRITATION, HEADACHE, DIZZINESS, NAUSEA, AND INCOORDINATION. MAY BE IRRITATING TO THE SKIN AND EYES. OVEREXPOSURE MAY CREATE A CANCER RISK. CAREFULLY READ ADDITIONAL INFORMATION ON THE BACK DISPLAY PANEL.
NET CONTENTS: 12 OZ. (340 g)
Plastic PrimerPlastic PrimerAutomotive Refi nishing PaintAutomotive Refi nishing Paint
Label contents have been reviewed and approved by Ford Motor Company. Label should NOT be changed for any reason or under any circumstance. Ford Motor Company recommends using InDesign 1.5 for printing this label. Any questions, call Angela Linehan at Brown Art: 313-565-7020.
DO NOT MODIFY
BROWN ART PRINTING INSTRUCTIONS FOR SERVICE PROVIDER REPORT
FORD MOTOR COMPANY RECOMMENDS USING INDESIGN 1.5 FOR PRINTING THIS DOCUMENT
PUBLICATION NAME: ml1136fn
PACKAGE DATE: 10/29/02 9:49 AMCreation Date: Modifi cation Date: 10/29/02
CONTACT INFORMATION
Company Name: Brown Art CorporationContact: Angela LinehanAddress: 22065 West Outer DriveDearborn, MI 48124
Phone: 313 565-7020Fax: 313 565-7022Email: [email protected]
SPECIAL INSTRUCTIONS AND OTHER NOTES
Trim Size 8.5” wide 5.90625” tall
FONTS7 Fonts Used; 0 Missing, 0 Embedded, 0 Incomplete
- Name: HelveticaNeue-BoldCond; Type: Type 1, Status: OK- Name: HelveticaNeue-BoldExt; Type: Type 1, Status: OK- Name: HelveticaNeue-BoldExtObl; Type: Type 1, Status: OK- Name: HelveticaNeue-Condensed; Type: Type 1, Status: OK- Name: HelveticaNeue-Extended; Type: Type 1, Status: OK- Name: HelveticaNeue-MediumCond; Type: Type 1, Status: OK- Name: ZapfDingbats; Type: Type 1, Status: OK
COLORS AND INKS4 Process Inks; 2 Spot InksCMS is OFF
- Name and Type: Process Cyan; Angle: 75.000; Lines/Inch: 70.000- Name and Type: Process Magenta; Angle: 15.000; Lines/Inch: 70.000- Name and Type: Process Yellow; Angle: 0.000; Lines/Inch: 70.000- Name and Type: Process Black; Angle: 45.000; Lines/Inch: 70.000
- Name and Type: PANTONE 485 CVC; Angle: 45.000; Lines/Inch: 70.000- Name and Type: PANTONE Process Black CVC; Angle: 45.000; Lines/Inch: 70.000
PRINT SETTINGSReader Spreads: NoEven/Odd Pages: BothPages: AllProof: NoTiling: NoneScale: 100%Center in Printable Area: YesPrinter’s Marks: NoneBleed: 18 ptColor: CompositeIn-Rip Trapping: NoSend Image Data: AllOPI/DCS Image Replacement: YesPage Size: LetterPaper Dimensions: 11 in x 8.5 inOrientation: Landscape