Catalogue 84pp Sep16 OPjambp.com/upload/section/3/pdf/58ba29983f94e.pdf · JAM-W A4 Wedge Anchor...

13

JAMThe Professional Standard

13


JAM Fixings

14


JAM-W Steel Wedge Anchor

20001 Zinc Plated20003 Hot Dip Galvanized

2000106050 - W M6-5/50 6 x 45 36 8 5 100 1.78 2.54 2000106065 - W M6-10/65 6 x 55 46 8 10 100 2.90 2.54 2000108060 2000308060 W M8-5/60 8 x 55 45 15 5 100 3.13 5.55 2000108075 2000308075 W M8-10/75 8 x 65 55 15 10 100 4.67 5.55 2000108090 2000308090 W M8-25/90 8 x 65 55 15 25 100 4.67 5.55 2000108110 2000308110 W M8-45/110 8 x 65 55 15 45 100 4.67 5.55 2000110070 2000310070 W M10-10/70 10 x 60 48 30 10 100 4.01 7.86 2000110090 2000310090 W M10-20/90 10 x 70 58 30 20 100 5.86 7.86 2000110100 2000310100 W M10-30/100 10 x 70 58 30 30 100 5.86 7.86 2000110110 2000310110 W M10-40/110 10 x 70 58 30 40 100 5.86 7.86 2000110120 2000310120 W M10-50/120 10 x 70 58 30 50 100 5.86 7.86 2000112075 2000312075 W M12-5/75 12 x 65 55 50 5 100 4.68 11.00 2000112090 2000312090 W M12-5/90 12 x 80 70 50 5 120 7.58 11.00 2000112105 2000312105 W M12-10/105 12 x 90 80 50 10 150 9.90 11.00 2000112120 2000312120 W M12-25/120 12 x 90 80 50 25 150 9.90 11.00 2000112170 2000312170 W M12-75/170 12 x 90 80 50 75 150 9.90 11.00 2000116100 2000316100 W M16-5/100 16 x 90 75 100 5 150 9.40 19.00 2000116120 2000316120 W M16-5/120 16 x 110 95 100 5 150 15.11 19.00 2000116140 2000316140 W M16-25/140 16 x 110 95 100 25 180 15.11 19.00 2000116215 2000316215 W M16-100/215 16 x 110 95 100 100 180 15.11 19.00 2000120170 2000320170 W M20-30/170 20 x 130 115 200 30 220 19.50 19.99

Item No. Description Bore x Hole Depth Setting Depth Tightening Torque Fixture Base Material Recommended Load* Item No. d0 x h1 hs (mm) Tinst (Nm) Thickness Thickness Tensile Load Shear Load (Zinc Plated) (Hot Dip Galvanized) (mm) tfix (mm) h (mm) (kN) (kN)

*Factor of Safety=3(Tension); 2.52(Shear)

2000206065 W M6-10/65 A4 6 x 55 46 8 10 100 2.90 2.54 2000208075 W M8-10/75 A4 8 x 65 55 15 10 100 4.67 5.55 2000208090 W M8-25/90 A4 8 x 65 55 15 25 100 4.67 5.55 2000208115 W M8-50/115 A4 8 x 65 55 15 50 100 4.67 5.55 2000210070 W M10-10/70 A4 10 x 60 48 30 10 100 4.01 7.86 2000210090 W M10-20/90 A4 10 x 70 58 30 20 100 5.86 7.86 2000210110 W M10-40/110 A4 10 x 70 58 30 40 100 5.86 7.86 2000212090 W M12-5/90 A4 12 x 80 70 50 5 120 7.58 11.00 2000212105 W M12-10/105 A4 12 x 90 80 50 10 150 9.90 11.00 2000212120 W M12-25/120 A4 12 x 90 80 50 25 150 9.90 11.00 2000216100 W M16-5/100 A4 16 x 90 75 100 5 130 9.40 19.00 2000216120 W M16-25/120 A4 16 x 90 75 100 25 130 9.40 19.00 2000216140 W M16-25/140 A4 16 x 110 95 100 25 170 15.11 19.00

Item No. Description Bore x Hole Depth Setting Depth Tightening Torque Fixture Base Material Recommended Load* d0 x h1 hs Tinst Thickness Thickness Tensile Load Shear Load (mm) (mm) (Nm) tfix (mm) h (mm) (kN) (kN)

*Factor of Safety=3(Tension); 2.52(Shear)

JAM-W A4 Wedge Anchor

20002 Stainless Steel A4 (316)

Installation of JAM-W Steel Wedge Anchor

1

1. Drill to specified diameter and depth.2. Clean the hole with blow-out bulb.3. Drive anchor carefully with hammer into hole until nut and washer are flush with fixture.4. Tighten with the torque wrench to the recommended torque value.

Features• dependable, economical anchor, externally threaded• efficient through fixing, torque controlled expansion

Application• high racking, safety barriers, hand rails, channels, brackets,

cable trays, ducts and suspended ceilings

Material• steel, zinc plated 5µm• steel, hot dip galvanized 45µm• A4/316 Stainless Steel

Base material• concrete (Non-cracked concrete fcc = 30N/mm2)

2 3 4

JAM Anchor Bolts (JAM-W)

15


2011106025 2011206025 D M6 x 25 8 x 28 25 5 100 M6 x 10 1.80 2.00 2011108030 2011208030 D M8 x 30 10 x 33 30 10 100 M8 x 13 3.60 3.00 2011110040 2011210040 D M10 x 40 12 x 44 40 20 100 M10 x 15 4.80 4.60 2011112050 2011212050 D M12 x 50 16 x 54 50 40 150 M12 x 18 7.80 8.00 2011116065 2011216065 D M16 x 65 20 x 71 65 70 200 M16 x 23 11.00 12.50 2011120080 2011220080 D M20 x 80 25 x 86 80 150 200 M20 x 34 12.00 18.00 2011110041 2011210041 D M20 x 80 13 x 44 80 150 200 M20 x 34 12.00 18.00

Item No. Item No. Description Bore x Hole Depth Setting Depth Tightening Torque Base Material Thread Ø x Length Recommended Load d0 x h1 hs (mm) Tinst (Nm) Thickness (mm) Tensile Load Shear Load (Zinc Plated) (Hot Dip Galvanized) (mm) h (mm) (kN) (kN)

2011406025 D M6 x 25 A4 8 x 28 25 5 100 M6 x 10 1.80 2.00 2011408030 D M8 x 30 A4 10 x 33 30 10 100 M8 x 13 3.60 3.00 2011410040 D M10 x 40 A4 12 x 44 40 20 100 M10 x 15 4.80 4.60 2011412050 D M12 x 50 A4 16 x 54 50 40 150 M12 x 18 7.80 8.00 2011416065 D M16 x 65 A4 20 x 71 65 70 200 M16 x 23 11.00 12.50 2011420080 D M20 x 80 A4 25 x 86 80 150 200 M20 x 34 12.00 18.00

Item No. Description Bore x Hole Depth Setting Depth Tightening Torque Base Material Thread Ø x Length Recommended Load d0 x h1 hs (mm) Tinst (Nm) Thickness (mm) Tensile Load Shear Load (mm) h (mm) (kN) (kN)

JAM-D Steel Drop In Anchor


JAM-D A4 Drop In Anchor


Features • safe, fast and easy expansion • movement controlled expansion • short embedment

Application • suspension threaded rod for ceiling, ventilation and sprinkler systems, steel brackets.Material • steel, zinc plated 5µm steel, hot dip galvanized 45µm A4/316 stainless steel

Base material • concrete (Non-cracked concrete fcc = 30N/mm2)

Installation of JAM-D Drop In Anchor

1 2 3 4 5

1. Drill to specified diameter and depth.2. Clean the hole with blow-out bulb.3. Insert anchor into the hole by hammer.4. Install anchor using proper setting tool. Setting tool to be driven into anchor until setting tool's shoulder meets top of anchor.5. Use a torque wrench to apply a required tightening torque.

*Head shape of M6 & M8

**Head shape of M10 to M20

JAM Anchor Bolts (JAM-D)

16

JAMThe Professional Standard JAM Anchor Bolts (JAM-S, JAM-SF/SC/SE/SH)

2010206045 2011606045 SH 8 x 45 8 M6 x 50 38 10 7 100 2.1 3.52010206060 2011606060 SH 8 x 60 8 M6 x 64 44 10 14 100 2.8 3.52010208060 2011608060 SH 10 x 60 10 M8 x 66 48 20 10 100 4.0 4.8 2010208085 2011608085 SH 10 x 85 10 M8 x 91 48 20 35 100 4.0 4.8 2010208110 2011608110 SH 10 x 110 10 M8 x 110 48 20 60 100 4.0 4.8 2010210065 2011610065 SH 12 x 65 12 M10 x 71 54 35 9 120 4.1 7.8 2010210080 2011610080 SH 12 x 80 12 M10 x 86 61 35 24 120 5.9 7.8 2010210110 2011610110 SH 12 x 110 12 M10 x 116 61 35 54 120 5.9 7.82010212095 2011612095 SH 16 x 95 16 M12 x 101 76 50 20 150 8.3 9.52010212110 2011612110 SH 16 x 110 16 M12 x 116 76 50 55 150 8.3 9.5

2011706045 SH 8 x 45 8 M6 x 50 38 10 7 100 2.1 3.5 2011706060 SH 8 x 60 8 M6 x 64 44 10 14 100 2.8 3.5 2011708060 SH 10 x 60 10 M8 x 66 48 20 10 100 4.0 4.8 2011708085 SH 10 x 85 10 M8 x 91 48 20 35 100 4.0 4.8 2011708110 SH 10 x 110 10 M8 x 110 48 20 60 100 4.0 4.8 2011710065 SH 12 x 65 12 M10 x 71 54 35 9 120 4.1 7.8 2011710080 SH 12 x 80 12 M10 x 86 61 35 24 120 5.9 7.8 2011710110 SH 12 x 110 12 M10 x 116 61 35 54 120 5.9 7.8 2011712065 SH 16 x 65 16 M12 x 73 56 50 10 110 5.0 8.5 2011712095 SH 16 x 95 16 M12 x 101 76 50 20 150 8.3 9.5 2011712110 SH 16 x 110 16 M12 x 116 76 50 55 150 8.3 9.5

Item No. Description Hole Thread Size x L Min. Setting Tightening Torque Fixture Base Recommended Load Diameter d0 (mm) Depth hs Tinst (Nm) Thickness Material Tensile Load Shear Load (mm) (mm) tfix (mm) Thickness (mm) (kN) (kN)

2010106040 S 8 x 40 8 M6 x 50 32 8 8 80 1.9 3.0 2010108050 S 10 x 50 10 M8 x 60 40 25 10 100 3.8 4.4 2010110060 S 12 x 60 12 M10 x 69 48 40 12 120 5.5 7.2 2010110075 S 12 x 75 12 M10 x 84 48 40 27 150 5.5 7.2


2010606040 2010706040 S 8 x 40 A2 8 M6 x 50 28 8 12 80 1.9 2.5 2010608050 2010708050 S 10 x 50 A2 10 M8 x 60 32 25 18 100 3.0 5.02010610060 2010700060 S 12 x 60 A2 12 M10 x 69 38 40 22 120 3.4 6.0*A4 stainless steel on request

Item No. Item No. Description Hole Thread Size x L Min. Setting Tightening Torque Fixture Base Recommended Load Diameter d0 (mm) Depth hs Tinst (Nm) Thickness Material Tensile Load Shear Load (mm) (mm) tfix (mm) Thickness (mm) (kN) (kN)

Item No. Item No. Description Hole Thread Size x L Min. Setting Tightening Torque Fixture Base Recommended Load Diameter d0 (mm) Depth hs Tinst (Nm) Thickness Material Tensile Load Shear Load (mm) (mm) tfix (mm) Thickness (mm) (kN) (kN)

JAM-S Steel Sleeve Anchor

20101 Zinc Plated

JAM-S Steel Sleeve Anchor

20106 Stainless Steel A2 (304)20107 Stainless Steel A4 (316)

JAM-SH Steel Sleeve Anchor


JAM-SH Steel Sleeve Anchor


Installation of JAM-S, JAM-SH Sleeve Anchor

1 2 3 4 5

1. Drill to specified diameter and depth.2. Clean the hole with blow-out bulb.3. Push anchor carefully with hand into hole until nut and washer are flush with fixture.4. Tighten with the wrench to the recommended torque value.

Application• installing pipe bracket, trucking, cable tray and suspended ceilings.

Light to medium metalwork, hand rails, signs and gates etc.

Material• steel, zinc plated 5µm;

A2/304 stainless steel; A4/316 stainless steel

Base material• concrete, brick, masonry and hollow brick (Concrete fcc = 30N/mm2)

17

JAMThe Professional StandardJAM Anchor Bolts (JAM-S, JAM-SF/SC/SE/SH)

2001106045 SF 8 x 45 8 M6 x 45 32 8 13 80 1.3 2.3 2001106060 SF 8 x 60 8 M6 x 60 32 8 28 80 1.3 2.3 2001108060 SF 10 x 60 10 M8 x 60 45 25 15 100 2.3 3.1 2001108085 SF 10 x 85 10 M8 x 85 45 25 40 100 2.3 3.1 2001108110 SF 10 x 110 10 M8 x 110 45 25 65 100 2.3 3.1


JAM-SF A2 Countersunk Head Sleeve Anchor


2010406040 SC 8 x 48 8 x 55 M6 x 78 (48) 40 10 0 80 0.20 2010408050 SC 10 x 60 10 x 65 M8 x 100 (60) 50 25 0 100 0.40

Item No. Description Bore x Hole Depth Thread Size x L (L2 ) Setting Depth Tightening Torque Fixture Base Safe Working d0 x h1 (mm) hs (mm) Tinst (Nm) Thickness Material Load (kN) (mm) tfix (mm) Thickness (mm)

2010506040 SE 8 x 48 8 x 55 M6 x 78 (48) 40 10 0 80 1.6 2010506070 SE 8 x 70 8 x 75 M6 x 100(70) 40 10 0 80 1.6 2010508050 SE 10 x 60 10 x 65 M8 x 100 (60) 48 25 0 100 2.0 2010508080 SE 10 x 80 10 x 85 M8 x 117 (80) 48 25 0 100 2.0

Item No. Description Bore x Hole Depth Thread Size x L (L2 ) Setting Depth Tightening Torque Fixture Base Safe Working d0 x h1 (mm) hs (mm) Tinst (Nm) Thickness Material Load (kN) (mm) tfix (mm) Thickness (mm)

20104 Zinc Plated

JAM-SE Steel Sleeve Anchor

20105 Zinc Plated

Installation of JAM-SC, JAM-SE Steel Sleeve Anchor

1 2 3 4 5

1. Drill to specified diameter and depth.

2. Clean the hole with blow-out bulb.

3. Push anchor carefully with hand into hole until the washer are flush with concrete.

4. Tighten with wrench to the recommended torque value.

18


2000004020 4 x 20 4 2.0 - 3.0 100 20,000 25 0.8 0.4 0.4

2000005025 5 x 25 5 2.6 - 4.0 100 10,000 30 2.1 1.8 1.6

2000006030 6 x 30 6 3.5 - 5.0 100 10,000 35 3.3 2.6 2.4

2000007030 7 x 30 7 4.0 - 5.5 100 5,000 35 4.0 3.4 3.2

2000008040 8 x 40 8 4.5 - 6.0 100 5,000 50 4.5 4.2 3.9

2000010050 10 x 50 10 6.0 - 8.0 50 2,500 60 9.4 5.2 4.8

2000012060 12 x 60 12 8.0 - 10.0 25 1,250 70 11.6 5.6

2000014070 14 x 70 14 10.0 - 12.0 20 1,000 85 19.5 7.0

2000016080 16 x 80 16 12.0 - 14.0 10 500 95 24.9

Item No. Dimension Drill Screw Pieces per Min. Drill

Ø x L mm Ø mm Ø mm Box Carton Depth / mm Concrete B25 Bricks MZ20 Sand lime full

brick KSV20

Pull-out results in following building materials kN:

JAM Series - Nylon Wall Plug

2100006040 6 x 40 6 4.0 - 5.0 100 4,000 45 1.0 0.7 0.3

2100008050 8 x 50 8 5.0 - 6.0 100 2,000 60 1.6 1.2 0.6

2100010060 10 x 60 10 6.0 - 7.0 50 1,000 70 1.9 1.3 1.1

Item No. Dimension Drill Screw Pieces per Min. Drill

Ø x L mm Ømm Ø mm Box Carton Depth / mm Concrete B25 Hollow bricks Light concrete G4Pull-out results in following building materials kN:

ALLFA Series Mega Plug with Flange

Example of application

Compact materials Hollow materials Plasterboards

• Wall-plug of high quality nylon with screw guidance and anti-rotating-system. It can be used with several kinds of screws as woodscrews or chipboard screws. The plug works in all building materials with high densities as concrete or bricks

• Light Duty Application• Fixing Electrical conduit

• Wall-plug of high quality nylon with screw guidance and anti-rotating-system. It can be used with several kinds of screws as woodscrews or chipboard screws. The plug works in all building materials with high densities as concrete or bricks

• Light Duty Application• Fixing Electrical conduit

Nylon

JAM Series & ALLFA Series

19


2284910080 10 x 80 10 30 50 500 4.4 3.9 3.9

2284910100 10 x 100 10 50 50 500 4.4 3.9 3.9

2284910120 10 x 120 10 70 50 500 4.4 3.9 3.9

2284910140 10 x 140 10 90 50 500 4.4 3.9 3.9

2284910160 10 x 160 10 110 50 500 4.4 3.9 3.9

2284910180 10 x 180 10 130 50 500 4.4 3.9 3.9

Item No. Dimension Drill Fixture Thickness Pieces per

ø x L mm mm mm Box Carton Concrete B25 Bricks MZ20 Sand lime full

brick KSV20


JAM-JN Series Screw-nail Anchor, Cylindrical Head

JAM-JN Series Screw-nail Anchor, A2 Stainless Steel

Cylindrical Head

JAM Series - 10mm Frame Anchor

2235005050 5 x 50 5 30 200 2000 30 1.2 1.1 1.0

2235005060 5 x 60 5 40 200 2000 30 1.2 1.1 1.0

2235006030 6 x 30 6 5 200 2000 35 1.4 1.3 1.1

2235006040 6 x 40 6 15 200 2000 35 1.4 1.3 1.1

2235006050 6 x 50 6 25 200 2000 35 1.4 1.3 1.1

2235006060 6 x 60 6 35 200 2000 35 1.4 1.3 1.1

2235006080 6 x 80 6 55 200 2000 35 1.4 1.3 1.1

2235006100 6 x 100 6 75 100 1000 35 1.4 1.3 1.1

2235008060 8 x 60 8 20 100 1000 50 2.1 1.9 1.7

2235008080 8 x 80 8 40 100 1000 50 2.1 1.9 1.7

2235008100 8 x 100 8 60 100 1000 50 2.1 1.9 1.7

2235010080 10 x 80 10 30 50 500 60 3.5 3.2 3.2

2235010100 10 x 100 10 40 50 500 60 3.5 3.2 3.2

Item No. Dimension Drill Fixture Thickness Pieces per Min. Drill

ø x L mm ø mm mm Box Carton Depth / mm Concrete B25 Bricks MZ20 Sand lime full

brick KSV20

Item No. Dimension Drill Fixture Thickness Pieces per Min. Drill

ø x L mm ø mm mm Box Carton Depth / mm Concrete B25 Bricks MZ20 Sand lime full

brick KSV20

• Consists of a nylon plug with cylindrial head and a pozidriv nail-screw, yellow zinc plated.

• Suitable for fixings on concrete, bricks and other high-density material.

• Consists of a nylon plug with cylindrical head and a pozidriv nail-screw, stainless steel A2.

• Suitable for outdoor and wet-room fixings on concrete, bricks and other high-density material.

• Material: Nylon (Polyamid 6)• Temperature resistance: from -40º elsius to +80º elsius

2234005050 5 x 50 5 30 200 2000 30 1.2 1.1 1.0

2234005060 5 x 60 5 40 200 2000 30 1.2 1.1 1.0

2234006030 6 x 30 6 5 200 2000 35 1.4 1.3 1.1

2234006040 6 x 40 6 15 200 2000 35 1.4 1.3 1.1

2234006050 6 x 50 6 25 200 2000 35 1.4 1.3 1.1

2234006060 6 x 60 6 35 200 2000 35 1.4 1.3 1.1

2234006080 6 x 80 6 55 200 2000 35 1.4 1.3 1.1

2234008060 8 x 60 8 20 100 1000 50 2.1 1.9 1.7

2234008080 8 x 80 8 40 100 1000 50 2.1 1.9 1.7

2234008100 8 x 100 8 60 100 1000 50 2.1 1.9 1.7

2234010080 10 x 80 10 30 50 500 60 3.5 3.2 3.2

2234010100 10 x 100 10 40 50 500 60 3.5 3.2 3.2

JAM Series Screw-nail Anchor, JAM-JN



• Consists of a nylon plug with countersunk head and a pozidriv screw, yellow zinc plated.

• Suitable for fixings on concrete, bricks and other high-density material.

• Material: Nylon (Polyamid 6)• Temperature resistance: from -40º elsius to +80º elsius

20

JAMThe Professional Standard JAM-SK Hex. Washer Head Concrete Screw Anchor

Material Standard: EN 10263-4

Finishing: A4 Stainless Steel to ISO 3506 : 1997

Zinc Plated to ISO 4042:1999

Ruspert Coating to ISO 9223

JAM-SK Screw Anchor Hex. Washer Head Concrete Screw Anchor

2018108065 SK 8 5/65mm 65 52018108075 SK 8 10/75mm 75 102018110065 SK10 5/65mm 65 52018110075 SK10 5/75mm 75 52018110080 SK10 5/80mm 80 52018110100 SK10 25/100mm 100 252018110120 SK10 45/120mm 120 452018112100 SK12 5/100mm 100 52018112110 SK12 15/110mm 110 152018112130 SK12 35/130mm 130 352018116130 SK 16 20/130mm 130 20

2017008065 SK 8 5/65mm 65 52017008075 SK 8 10/75mm 75 102017010065 SK10 5/65mm 65 52017010080 SK10 5/80mm 80 52017010100 SK10 25/100mm 100 252017012110 SK12 10/110mm 110 152017012130 SK12 30/130mm 130 35

2018010075 SK10 5/75mm 75 52018010120 SK10 45/120mm 120 452018012110 SK12 10/110mm 110 152018016130 SK16 15/100mm 100 15

Item No. Description Anchor Length Fixture thickness(GMS) l (mm) tfix (mm)

Item No. Description Anchor Length Fixture thickness(Zinc Plated) l (mm) tfix (mm)

JAM-SK Mechanical Galvanized (minimum 45µm) JAM-SK A4/316 Stainless (Ruspert Coating for seperation)

JAM-SK Zinc Plated (minimum 5µm)

M8 M10 M12 M16 JAM-SK Screw Anchor

cracked concreteRecommended loads, tension C25/30 Nrec [kN] 1.5 2.8 4.4 4.6 5.8Recommended loads, shear C20/25 Vrec [kN] 4.5 7.1 12.6 21.6 21.6

non-cracked concreteRecommended loads, tension C25/30 Nrec [kN] 3.3 5.9 9.2 10.9 13.6Recommended loads, shear C20/25 Vrec [kN] 4.5 7.1 12.6 21.6 21.6Spacing and Edge distance Effective anchorage depth hef [mm] 51 59 76 - 90Reduced anchorge depth hef,red [mm] - - - 65 -Nominal embedment depth hnom [mm] 65 75 95 85 110Minimum thickness concrete slab hmin [mm] 100 100 130 150 170Minimum Spacing Smin [mm] 50 60 70 100 100Minimum Edge Distance Cmin [mm] 50 60 70 100 100Installation parameters Thread Diameter* D [mm] 9.95 12.5 14.2 18.6 18.6Drill hole diameter do [mm] 8 10 12 16 16Diameter of clearance hole in the fixture df [mm] 12 14 16 20 20Depth of Drill hole h1 [mm] 80 90 115 130 130Thickness of fixture Tfix [mm] 5-10 5-45 5-35 5-15 5-20Installation torque Tinst [Nm] 40 60 80 100 100Max. Torque moment, machine setting Tmax [Nm] 185 350 350 350 350Material Nominal tensile strength fuk [N/mm²] 870 850 850 850 850Yield strength fyk [N/mm²] 750 750 780 780 780Stress Cross-Section As [mm²] 41.3 67.1 97.6 - -Moment of resistance W [mm³] 37.4 77.4 136.1 - -Characteristic bending resistance M0Rk,s [Nm] 39.0 78.9 138.8 - -

Recommended loads for single anchor without influence of spacing and edge distance.With overall global safety factor = 3.0.

Loads and Performance Data

Steel/Stainless Steel

Catalogue 84pp Sep16 OPjambp.com/upload/section/3/pdf/58ba29983f94e.pdf · JAM-W A4 Wedge Anchor...

Documents

Transcript of Catalogue 84pp Sep16 OPjambp.com/upload/section/3/pdf/58ba29983f94e.pdf · JAM-W A4 Wedge Anchor...