Dimensions & Wedge Anchor Performance Data - Allied Bolt
Transcript of Dimensions & Wedge Anchor Performance Data - Allied Bolt
Wedge Anchor
42a
Dimensions &Performance Data
eziSrohcnAetercnocisp000 isp0002
elisne rT aehS
4/3-1x02-4/1
1
8/3 8/7
0051 0092x02-4/1 4/3 8/1-1
4/1-2x02-4/1 8/7 4/1-13x02-4/1 2/1-1 4/3
4/1-3x02-4/1 8/7-1 4/1-24/3-2x81-61/5
4/1-18/1- 41 /3-1
009 01 0723x81-61/ 85 /3- 41 /3-14x81-61/ 85 /3- 12
4/1-2x61-8/3
2/1-1
8/3 2/1-1
0063 0014
4/3-2x61-8/3 8/7 4/3-13x61-8/3 8/1-1 3
4/1-3x61-8/3 8/3-1 22/1-3x61-8/3 8/5-1 8/7-24/3-3x61-8/3 8/7-1 4/3-2
5x61-8/3 8/1-3 4/3-22/1-6x61-8/3 8/5-4 8/1-2
7x61-8/3 4/3-4 4/3-54/3-2x31-2/1
2
4/ 21 /1-1
008 04 046
3x31-2/ 21 / 21 /1-14/1-3x31-2/ 41 / 63 1/31-14/3-3x31-2/ 41 / 41 /1-2
4x31-2/ 21 /1- 21 /1-24/1-4x31-2/ 21 /1- 41 /1-12/1-4x31-2/ 41 /3- 312/1-5x31-2/ 31 4/3-2
6x31-2/ 21 /1- 23 /1-27x31-2/ 21 /1- 84 /3-2
2/1-8x31-2/ 61 2/1-201x31-2/ 21 /1- 27 /1-221x31-2/ 21 /1- 29 /1-2
2/1-3x11-8/5
2/1-2
8/3 8/7-1
0056 0049
4x11-8/5 8/7 2/1-22/1-4x11-8/5 8/3-1 8/7-2
5x11-8/5 8/7-1 8/3-32/1-5x11-8/5 8/3-2 2/1-2
6x11-8/5 8/7-2 8/3-47x11-8/5 8/7-3 8/3-5
2/1-8x11-8/5 8/3-5 8/5-101x11-8/5 8/7-6 2/1-221x11-8/5 8/7-8 4/1-2
ICBO Approved Wedge Anchors FF-S-325 Group IIType 4, Class 1
Minimum Embedment(inches)
Fastens MaterialUp to
Thread LengthW x L Average Ultimate Tensile & Shear Values
etercnoc4
Wedge Anchor
42b
MaterialSpecifications
DescriptionA four-piece assembly consisting of (1) an anchor bolt threaded at one end with a unified pitch, and a shoulder at the opposite end whichretains a free-spinning clip, (2) a clip with three lateral slits and projections designed to exert greater holding power the greater the load
that is applied, (3) a hex nut, and (4) a flat washer.
Applications/Advantages
These are heavy-duty, non-bottom bearing anchors of greater shear strength than other light and medium-duty expansion anchors. Thedesign of the expansion clip assures full contact with the masonry. Wedge anchors withstand temperature fluctuations well. For best
performance, minimum anchor spacing should be 10 hole diameters and minimum edge distance be 5 hole diameters.
Material
Carbon Steel Type 304 StainlessAnchor Body: AISI 1018 - 12L14 or equivalent free-machining
carbon steelExpansion Wedge: AISI C1008 - 1010 or equivalent carbon steel
Nut: ASTM A-563 Grade-A carbon steelWasher: Carbon steel
Anchor Body: Type 304Cu (1/4" thru 3/4" diameters)Type 304 (7/8 thru 1-1/4" diams & all lengths over 7")
Expansion Wedge: Type 304 stainlessNut: 18-8 stainless
Washer: 18-8 stainless
Ultimate ShearStrength
See average test values as listed in above table. Important: The maximum working loads should not exceed 1/4 of the average ultimatevalues for a specific size.
Plating Steel wedge anchors are typically zinc or mechanically galvanizedplated
Stainless wedge anchors are usually supplied without any additionalcoating.
seulaVraehS&elisneTetamitlUegarevA
eziSrohcnAetercnocisp000 e4 tercnocisp0002
elisne rT aehS
4/1-4x01-4/3
3
2/1 2/1-2
0027 008,41
2/1-4x01-4/3 01/7 2/1-24/3-4x01-4/3 1 8/1-22/1-5x01-4/3 4/3-1 4/3-2
6x01-4/3 5/1-2 2/1-24/1-6x01-4/3 2/1-2 3
7x01-4/3 4/1-3 4/1-22/1-8x01-4/3 4/3-4 8/3-2
01x01-4/3 4/1-6 8/3-221x01-4/3 4/1-8 2/1-2
6x9-8/72/1-3
8/5- 21 /1-2008,2 01 05,128x9-8/ 87 /5- 23 /1-2
01x9-8/ 87 /5- 45 /1-26x8-1
41 2/1-2
007,31 003,729x8-1 4 4/1-221x8-1 7 2/1-2
9x7-4/118/5-5
8/1- 42 /1-3023,7 52 30,83
21x7-4/1 81 /1- 45 /1-3
W x L
ICBO Approved Wedge Anchors FF-S-325 Group IIType 4, Class 1
Minimum Embedment(inches)
Fastens MaterialUp to
Thread Length