Catalogo Soportes Tuberia Aislada

1GENERAL INTRODUCTION

ipe Shields Inc. pioneered the first insulated pipe support, in 1971, for use on HVAC and plumbing lines. These supports were designed because fiberglass pipe insulation is not strong enough to carry

the load at the point of support without crushing. The various methods contractors employed to compensate for this weakness were inconsistent, non-uniform and labor intensive, often resulting in damage to the vapor barrier and/or pipe insulation. The insulated pipe support filled the need for an energy efficient, economical and practical support. Pipe Shields Inc. has developed a large and growing family of insulated pipe supports, using its standard concept of incorporating materials strong enough to carry the load while insulating the pipe at the same time. No welding to the pipe is required (except for insulated positive anchors and insulated pipe riser clamps) and no direct metal-to-metal heat path exists. Insulated pipe supports meet an assortment of requirements, including:

Pipe supported on: o Flat Surface o Pipe Roll o Clevis Hanger

Gas Steam Super Heated Steam Chilled Water Styrene Guide Supports Sliding Supports Restrained Supports

Anchors Pipe Hangers Pipe Riser Clamps Thermal Growth Small or Large Maximum Support Spacing Light, Medium or Heavy Loads Ultra-High Temperatures Minimum Overhead Clearance Minimum Horizontal Clearance Minimum Field Labor Minimum Friction Loads Easy Installation

Other products designed, manufactured and supplied not included in this catalog are:

1. Cryogenic supports 2. Seismic pipe restraints 3. Heat-traced pre-insulated pipe supports 4. Pipe supports used in computer chip, styrene plants and oil refineries 5. Pipe supports for solar energy projects to accommodate expansion travels in excess of 5- 0

Our highly sophisticated products are a direct result of years of research, engineering and design to develop cost efficient products for the power, petrochemical, chemical and commercial markets. We work closely with engineering firms and in-house engineering departments of owners to provide working solutions to meet their engineering challenges. We have established proprietary specifications that have now become an industry standard used by owners, engineers and contractors throughout the world markets. If you have a pipe support need not met by any of the items described in this catalog, please contact us at

713-731-0030 or 1-800-787-5914.

P

FRONEK GROUP

CATALOG PS-2004

2TEMPERATURE, DIMENSIONAL AND MATERIAL VARIANCES

Temperature Ranges Pipe Shi elds Inc. str ongly recommen ds the foll owing temper ature range s for our stan dard insulati on material: Material Temperature Calcium Silicate +40oF to + 1200 oF Urethane -275 oF to +275 oF Foamglas -450 oF to +900 oF Material Variances Our standard paint finish is SP150 Red Oxide Primer which meets full EPA and California safety regulations. Other paint finished are available upon request:

Hot dipped galvanized In-organic zinc (CZ11HS) Dupont (Corlar) 25P epoxy SP145 grey oxide Carbothane 134HG Carbozinc 859

Slide plate material and other field welded material are coated with deoxaluminate (silver coating) Model Designation for Alternate Insulation Materials Polyurethane Add U after Catalog Model Number Example: B1000U Urethane/Foamglas - Add UF after Catalog Model Number Example: B1000UF Calcium Silicate/Foamglas - Add CF after Catalog Model Number Example: B1000CF

FRONEK GROUP

CATALOG PS-2004

3INSULATED PIPE SUPPORT SELECTION GUIDEFRONEK GROUP

CATALOG PS-2004

1.A. WaterB. Steam, Gas, or Air

2. APPLICATIONA. Pipe supported from below

a. On flat surfaceb. On pipe roll

B. Pipe supported from abovea. In clevis or 2-bolt hanger

The product data sheets describing each model refer to other models in the catalog with features such as load rating, axial or lateral travel, or restraint, etc. which you may have an interest.

USE OF THE INSULATED PIPE SUPPORT SELECTION GUIDE

XX

OR AIR

TABLE 6 X

TABLE 3

TABLE 1TABLE 2

XX

XTABLE 4TABLE 5

X

XX

X

XX

ONPIPE ROLL

ON FLATSURFACE

APPLICATIONPIPE SUPPORTED

FROM ABOVEFROM BELOW

If you have a pipe support need not met by any of the items described in this catalog, please contact us at 713-731-0030 or 1-800-787-5914.

SERVICE

These Selection Guide Tables are organized by:

The table on the following pages will assist you in making a selection of the proper and most economicinsulated pipe support for your application.

WATER

SERVICE

STEAMGAS IN CLEVIS OR

2-BOLT HANGER


CATALOG PS-2004

WATERPIPE SUPPORTED FROM BELOW ON FLAT SURFACE

B1000 B1100 B1200 B1300B2000 B2100 B2200 B2300B3000 B3100 B3200 B3300B4000 B4100 B4200 B4300

ASME A1000 A3000 A5000 A7000 A7200 A7400 B5000 B5100 B5200 B5300 B7000 B7100 B7200 B7300B31.1 A2000 A4000 A6000 B6000 B6100 B6200 B6300 B8000 B8100 B8200 B8300

PipeSize (Ref)1/2 7 11 123/4 7 12 131 7 13 14

1 1/2 9 15 162 10 15 17

2 1/2 11 12 14 16 213 12 12 13 17 20 35 45 55 32 45 55

3 1/2 13 12 13 16 19 35 45 55 33 45 554 14 13 14 17 19 35 45 55 35 45 555 16 12 14 16 17 35 45 55 33 45 556 17 10 12 13 14 26 34 45 55 30 45 558 19 7 8 11 12 21 29 45 55 26 45 5510 22 6 6 7 10 18 25 24 45 55 21 42 5512 23 8 14 20 31 20 40 55 65 17 36 54 6514 25 8 13 22 31 20 40 55 65 18 35 53 6516 27 12 21 28 19 37 55 65 16 34 50 6518 28 10 19 26 17 34 52 65 15 30 46 6120 30 9 17 23 15 31 46 62 14 27 41 5524 32 14 18 12 24 36 48 10 21 32 4330 33 10 12 11 21 32 43 9 19 29 3936 35 9 18 28 37 8 16 24 3342 36 8 16 24 32 7 14 21 28

Note:

Pipe Diameter: 8" standard weightWater20' - 0Insulated pipe support model number

support spacing. In this case, Model A7200 is selected since it is capable of handling 21'-0 supportspacing. The Index Sheets to Sections "A" & "B" indicate some of the differences between models.Check Product Data Sheet for description before making a final selection. In this example, if thesupport is required to handle +/-4 1/2" of axial travel, Model B2000 would be selected (Section "B"Index & Product Data Sheet B2000).

The maximum hanger spacing s hown in Table 1 are derived from load ratings (see Product Data Sheets) of Pipe Shields Inc. models, assuming weight of standard pipe, water, and 2" insulation. The customer should be guided by the hanger spacings allowed by the applicable code or the project engineers' specifications before making a selection. Refer to the appropriate Product Data Sheets for additional information such as load rating, compensation for temperature, axial or lateral travel, or res traint, etc.

In table 1, for 8" pipe size, find the model(s) rated for handling 20'- 0 or greater

Service:

Determine:Support Spacing:

Method:

Example: Given:

TABLE 1SERVICE:APPLICATION:

MAXIMUM HANGER SUPPORT SPACING - FEETFOR VARIOUS PIPE SH IELDS, INC.INSULATED PIPE SUPPORT MODELS

CommercialLight Industrial

w/ Load Distribution PlateHeavy Industrial

on Slide PadRated for Combined

Lateral and Vertical Loads


CATALOG PS-2004

STEAM, GAS OR AIRPIPE SUPPORTED FROM BELOW ON FLAT SURFACE

B1000 B1100 B1200 B1300B2000 B2100 B2200 B2300B3000 B3100 B3200 B3300B4000 B4100 B4200 B4300

ASME A1000 A3000 A5000 A7000 A7200 A7400 B5000 B5100 B5200 B5300 B7000 B7100 B7200 B7300B31.1 A2000 A4000 A6000 B6000 B6100 B6200 B6300 B8000 B8100 B8200 B8300

PipeSize (Ref)1/2 8 11 123/4 9 12 131 9 14 15

1 1/2 12 17 192 13 18 20

2 1/2 14 15 16 20 253 15 15 17 21 26 40 50 60 40 50 60

3 1/2 16 16 18 21 25 40 50 60 40 50 604 17 17 19 23 26 40 50 60 40 50 605 19 17 20 22 25 40 50 60 40 50 606 21 16 18 20 22 40 40 50 60 40 50 608 24 12 14 17 19 35 40 50 60 40 50 6010 26 10 10 13 17 31 40 40 50 60 36 50 6012 30 9 9 15 26 37 45 36 50 60 70 32 50 60 7014 32 8 9 15 25 40 45 38 50 60 70 34 50 60 7016 35 8 8 14 24 40 45 39 50 60 70 25 50 60 7018 37 14 24 40 45 38 50 60 70 34 50 60 7020 39 14 22 40 45 36 50 60 70 32 50 60 7024 42 11 20 36 45 32 50 60 70 28 50 60 7030 44 10 18 32 39 33 50 60 70 30 50 60 7036 48 9 15 27 33 50 60 70 29 50 60 7042 50 12 23 31 50 60 70 28 50 60 70

Note:

Pipe Diameter: 8" standard weightSteam30' - 0Insulated pipe support model number

The maximum hanger spac ing shown in Table 2 are derived from load ratings (see Product Data Sheets) of Pipe Shields Inc. models, assuming weight of standard pipe, and 2" insulation. The customer should be guided by the hanger spacings allowed by the applicable code or the project engineers' specifications before making a selection. Refer to the appropriate Product Data Sheets for additional information such as load rating, compensation for temperature, axial or lateral travel, or restraint, etc.

w/ Load Distribution PlateHeavy Industrial

on Slide PadRated for Combined

Lateral and Vertical Loads

support spacing. In this case, Model A7200 is selected since it is capable of handling 35'-0 supportspacing. The Index Sheets to Sections "A" & "B" indicate some of the differences between models.Check Product Data Sheet for description before making a final selection. In this example, if thesupport is required to handle +/-4 1/2" of axial travel, Model B2000 would be selected (Section "B"Index & Product Data Sheet B2000).

Example: Given:


MAXIMUM HANGER SUPPORT SPACING - FEETFOR VARIOUS PIPE SH IELDS, INC.INSULATED PIPE SUPPORT MODELS

CommercialLight Industrial

In table 2, for 8" pipe size, find the model(s) rated for handling 30'- 0 or greater

Service:


Method:


CATALOG PS-2004

WATERPIPE SUPPORTED FROM ABOVE IN CLEVIS OR 2-BOLT HANGER

D1000D2000

ASME A1000 A3000 D4000 D3000 D3100 D3200 D3300B31.1 A2000 A4000 A9000 D5000 D6000 D6100 D6200 D6300

PipeSize (Ref)1/2 7 11 12 133/4 7 12 13 151 7 14 15 17 19

1 1/2 9 16 18 19 222 10 17 18 21 29

2 1/2 11 16 18 21 243 12 17 18 20 25

3 1/2 13 16 17 19 224 14 16 18 19 225 16 15 16 19 21 406 17 14 15 16 21 408 19 13 13 15 22 3210 22 12 13 14 24 2812 23 11 12 13 22 2614 25 11 12 13 20 2316 27 10 11 12 21 26 4018 28 9 10 11 18 22 3320 30 9 9 10 16 18 28 3724 32 8 9 15 19 29 3830 33 11 13 19 26

Note:


MAXIMUM HANGER SUPPORT SPACING - FEET

In table 3, for 8" pipe size, find the model(s) rated for handling 20"- 0 or greatersupport spacing. In this case, Model D3000 is selected since it is capable of handling 22'-0 support spacing.The Index Sheets to Sections "A" & "D" indicate some of the differences between models. Check ProductData Sheet for description before making a final selection. In this example, if the clearance is above thesupport limited, Model D6000 might be selected (Section "D" Index & Product Data Sheet D6000).

Service:


Method:

Example: Given:

The maximum hanger spacing shown in Table 3 are derived from load ratings (see Product Data Sheets) ofPipe Shields Inc. models, assuming weight of standard pipe, water, and 2" insulation. The customer should beguided by the hanger spacings allowed by the applicable code or the project engineers' specifications before makingaection. Refer to the appropriate Product Data Sheets for additional information such as load rating,compensation for temperature, axial or lateral travel, or res traint, etc.


Clevis Hanger 2-Bolt Hanger

FOR VARIOUS PIPE SH IELDS, INC.PRE-INSULATED PIPE SUPPORT MODELS


CATALOG PS-2004

STEAM, GAS OR AIRPIPE SUPPORTED FROM ABOVE IN CLEVIS OR 2-BOLT HANGER

D1000D2000

ASME A1000 A3000 D4000 D3000 D3100 D3200 D3300B31.1 A2000 A4000 A9000 D5000 D6000 D6100 D6200 D6300

PipeSize (Ref)1/2 8 11 12 133/4 9 12 13 151 9 15 16 19 21

1 1/2 12 19 20 22 262 13 20 22 25 36

2 1/2 14 20 22 25 293 15 21 24 26 32

3 1/2 16 21 23 25 294 17 23 24 26 315 19 22 24 28 30 556 21 22 23 24 32 558 24 21 22 25 25 5210 26 20 22 24 40 4512 30 20 21 24 40 4514 32 21 23 25 38 55 6016 35 21 22 25 40 55 6018 37 21 22 25 40 49 6020 39 21 22 25 38 44 60 6524 42 20 21 24 40 50 60 6530 44 34 51 60 65

Note:



Clevis Hanger

FOR VARIOUS PIPE SH IELDS, INC.PRE-INSULATED PIPE SUPPORT MODELS

2-Bolt Hanger

MAXIMUM HANGER SUPPORT SPACING - FEET

The maximum hanger spacing shown in Table 4 are derived from load ratings (see Product Data Sheets) oPipe Shields Inc. models, assuming weight of standard pipe, and 2" insulation. The customer should be guided bythe hanger spacings allowed by the applicable code or the project engineers' specifications before making aselection. Refer to the appropriate Product Data Sheets for additional information such as load rating, compensationfor temperature, axial or lateral travel, or restraint, etc.

support spacing. In this case, Model A9000 is selected since it is capable of handling 25'-0 support spacing.The Index Sheets to Sections "A" & "D" indicate some of the differences between models. Check ProductData Sheet for description before making a final selection. In this example, if the clearance is above thesupport limited, Model D6000 might be selected (Section "D" Index & Product Data Sheet D6000).

Service:


Method: In table 4, for 8" pipe size, find the model(s) rated for handling 24'- 0 or greater

Example: Given:


CATALOG PS-2004

WATERPIPE SUPPORTED FROM BELOW ON PIPE ROLL

ASME A5000B31.1 A6000 A8000 A8200 A8400

PipeSize (Ref)1/2 73/4 71 7

1 1/2 92 10

2 1/2 11 15 183 12 15 17

3 1/2 13 12 164 14 15 165 16 14 156 17 12 13 248 19 9 10 1910 22 10 16 2212 23 12 23 3114 25 11 21 2816 27 10 19 2518 28 9 17 2320 30 8 15 2024 32 12 1630 33 9 12

Note:


The maximum hanger spacing shown in Table 5 are derived from load ratings (see Product Data Sheets) ofPipe Shields Inc. models, assuming weight of standard pipe, water, and 2" insulation. The customer should beguided by the hanger spacings allowed by the applicable code or the project engineers' specifications before makinga selection. Refer to the appropriate Product Data Sheets for additional information such as load rating,compensation for temperature, axial or lateral travel, or res traint, etc.

13

15121212

Service:


Method: In table 5, for 8" pipe size, find the model(s) rated for handling 18'- 0 or greatersupport spacing. In this case, Model A8200 is selected since it is capable of handling 19'-0 support spacing.The Index Sheet to Section "A" indicates some of the differences between models. Check Product DataSheet for description before making a final selection. If greater support spacings are desired, see Section "B"(Base Mounted Supports).

Example: Given:


A3000A4000

1315

Commercial1213

Light Insutrial w/Load Distribution Plate

MAXIMUM HANGER SUPPORT SPACING - FEETFOR VARIOUS PIPE SH IELDS, INC.PRE-INSULATED PIPE SUPPORT MODELS


CATALOG PS-2004

STEAM, GAS OR AIRPIPE SUPPORTED FROM BELOW ON PIPE ROLL

ASME A5000B31.1 A6000 A8000 A8200 A8400

PipeSize (Ref)1/2 83/4 91 9

1 1/2 122 13

2 1/2 14 18 223 15 19 21

3 1/2 16 19 214 17 20 235 19 20 226 21 18 20 368 24 15 17 3110 26 11 17 27 3812 30 13 23 40 5014 32 13 22 40 5016 35 13 22 39 5018 37 12 21 38 5020 39 12 20 36 4924 42 11 18 33 4430 44 9 16 29 3936 48 8 13 2442 50 11 20

Note:


Light Industrial w/ Load Distribution Plate

15

Example: Given:

151617

The maximum hanger spacing shown in Table 6 are derived from load ratings (see Product Data Sheets) of Pipe Shields Inc. models, assuming weight of standard pipe, and 2" insulation. The customer should be guided bythe hanger spacings allowed by the applicable code or the project engineers' specifications before making aselection. Refer to the appropriate Product Data Sheets for additional information such as load rating, compensationfor temperature, axial or lateral travel, or restraint, etc.


A3000

MAXIMUM HANGER SUPPORT SPACING - FEETFOR VARIOUS PIPE SH IELDS, INC.PRE-INSULATED PIPE SUPPORT MODELS

A4000

141718

Commercial1213

Service:


Method: In table 6, for 8" pipe size, find the model (s) rated for handling 25'-0 or greatersupport spacing. In this case, Model A8200 is selected since it is capable of handling 25'-0 or 31'-0 supportspacing. The Index Sheet to Section "A" indicates some of the differences between models. Check ProductData Sheet for description before making a final selection. If greater support spacings are desired, seeSection "B" (Base Mounted Supports).

FRONEK GROUP

INTRODUCTION SECTION A

INTRODUCTION

SECTION A

PRE-INSULATED PIPE SUPPORTS APPLICATION Commercial and Light Industrial Most Commercial applications are well served by Models A1000 and A2000, which are recommended for use on common 10-0 hanger space for small bore pipe sizes (see Selection Guide). However, should the need arise, because of increased hanger spacing or the manner in which the insulated support is mounted, heavier duty supports are available. As is readily seen in the Section Index on the following page, some models are meant for installation only in a clevis hanger, on a flat surface, or on a pipe roll. Other models may be installed in any two or all three mounting methods. The load ratings (see Product Data Sheets) reflect consideration for the manner in which each of these models will be mounted. Note that in the A7000 through A7400 Series and the A8000 through A8400 Series, the higher the model number, the higher the load rating. We are committed to providing the most economical and appropriate insulated pipe support to satisfy the requirements of the piping system.

If your requirements are not covered by the Product Data Sheets in this catalog, please contact us at 713-731-0030 or 1-800-787-5914.

Please acquaint yourself with the selection guide at the front of this catalog and the section index on the page following this introduction, for assistance in determining the most

appropriate support for your application.

FRONEK GROUP

CATALOG PS-2004

PIPESIZE FLAT CLEVIS PIPE

MODEL RANGE HOT COLD SURFACE HANGER ROLL DUTY

A1000 1/2 - 24 X X X LIGHTA2000 1/2 - 24 X X X LIGHTA3000 1/2 - 24 X X X MEDIUMA3000 1/2 - 4 X X MEDIUMA4000 1/2 - 24 X X X MEDIUMA4000 1/2 - 4 X X MEDIUM

A5000 2 1/2 - 42 X X X MED/HEAVYA6000 2 1/2 - 42 X X X MED/HEAVYA7000 2 1/2 - 42 X X X HEAVYA7200 6 - 42 X X X HEAVIERA7400 10 - 30 X X X HEAVIESTA8000 2 1/2 - 42 X X X HEAVYA8200 6 - 42 X X X HEAVIERA8400 10 - 30 X X X HEAVIEST

A9000 1/2 - 24 X X X HEAVY

PRE-INSULATED PIPE SUPPORTSCOMMERCIAL AND LIGHT INDUSTRIAL

PRIMARYAPPLICATION

INSTALLED ON

SECTION A INDEX

TO ORDER, specify:1. Quantity 202. Pipe Size & Type 2 IPS3. Insulation Thickness 2-1/24. Model Number A1000

EXAMPLE: (20) 2 x 2-1/2 A1000

FRONEK GROUP

CATALOG PS-2004

MODEL A1000 Insulated Pipe Support Regular Duty

A1

Features:

Compact Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Copper tubing sizes available Other I.D.'s and/or O.D.'s available on request Clamps available (see G-series) Performance Test Results on File: Available upon request.

Material Data:

A1000: Applicable PSI spec. doc.: No. 205.Insulation: Calcium Silicate asbestos-free,

treated with water repellant.Jackets: Galvanized Steel ASTM A-527.Glue: Industrial contact adhesive

Formal Submittal Sheets available

Application:

Model A1000 is designed for use on: Hot Water Vacuum Gas Cold Water Steam Air Dual Temperature Chilled Water

Intended for installation on: Flat Surfaces Band, ring or clevis pipe hanger

Note: Up to 1700F available upon request.Temperature Range: F to +1200F +40

FRONEK GROUP

CATALOG PS-2004

Hardware sold separately

A B A B A B A B A B A B A B A B A B4 24 4 24 4 24 4 24 4 24 4 24 6 24 6 24 6 246 24 6 24 6 24 6 24 6 24 6 24 6 24 6 24 6 246 20 6 20 6 20 6 20 6 20 6 20 9 20 9 20 9 20

6 20 6 20 6 20 6 20 9 20 9 20 9 206 20 6 20 6 20 6 20 9 16 9 16 9 16

9 16 9 16 9 16 9 16 9 16 9 1612 16 12 16 12 16 12 16 12 16 12 1618 16 18 16 18 16 18 16 18 16 18 16

200

TABLE III1200

0.750.500.30

7501000

350450

Mult.

CopperTubing

Size O.D.

250

5501000750

1200

300

Oper.Temp.

oF

To develop maximum load rating, use band, ring or clevis hanger with manufacturer'sload rating equal to or greater than values shown in Table I.

To develop maximum load rating, width of support surface should be at least 1/2 ofdimension "A" in Table II.

The load ratings represent average values obtained in accordance with acceptedmethods and are subject to normal manufacturing variations. Dimensions and ratingsare subject to change without notice.

Factor"F"

500 0.90

MAXIMUM LOAD

Pipe On Flat In Clevis

1 1/2Iron

Contact factory for other dimensions, temperatures, and loads.

Available in all insulation thicknesses.Insulation Thickness

2 2 1/2

To obtain load ratings for operating temperatures of 500 F and higher, multiply loadrating by factor "F" in Table III.

1/2 3/4 1

8 1/8 -10 1/812 1/8

5/8 - 1 5/8

4

2 1/82 5/8 - 4 1/8

550350

6580110140

150180225270

400450

3

8

56

141618

2420

160018002000

3 1/2

TABLE I750

600625675

TABLE II "B" = gauge of sheet metal jacket

PipeSize

1/2 - 1 1/2

6 - 78 - 1012 - 18

52 1/2 - 4

3

2 1/2

2

20 - 24

5 1/86 1/8

2300

10

1400575

500

Note: For higher load ratings, see A3000, A9000.

12

3 1/24

70100125

1 1/41 1/2

2

1

1/24060

Size

3/4

RATING (LBS)

Hanger(b) (c)

40

Surface(a) (c)

3545

A2

MODEL A2000 Insulated Pipe Support Regular Duty w/Extended Insulation

Application:

Model A2000 is designed for use on: Cold Water Chilled Water

Intended for installation on: Flat Surfaces Band, ring or clevis pipe hangers

Temperature Range: F to +1200F +40Note: Up to 1700F available upon request.

Features:

Compact Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Calcium silicate insulation extends 1'' beyond the galvanized sheet metal jacket providing for an easier vapor barrier joint with the pipe insulation Copper tubing sizes available Other I.D.'s and/or O.D.'s available on request Clamps available see (G-series) Performance Test Results on File: Available upon request.

Material Data:

A2000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive


FRONEK GROUP

CATALOG PS-2004



6 20 6 20 6 20 6 20 9 20 9 20 9 206 20 6 20 6 20 6 20 9 16 9 16 9 16

9 16 9 16 9 16 9 16 9 16 9 1612 16 12 16 12 16 12 16 12 16 12 1618 16 18 16 18 16 18 16 18 16 18 16

0.750.50

TABLE III1200 0.30

FactorTemp.


oF "F"

Note: For higher load ratings, see A4000, A9000.

5007501000

0.90

10

3 1/2

1214

4568

To obtain load ratings for operating temperatures of 500F and higher, multiply loadrating by factor "F" in Table III.

182024


To develop maximum load rating, use band, ring or clevis hanger with manufacturer'sload rating equal to or greater than values shown in Table I.

Contact factory for other dimensions, temperatures, and loads.

Available in all insulation thicknesses.

16

2000675

140016001800625

575

1 1/22

2 1/23

1/23/41

1 1/4

12 1/8

750

5/8 - 15/8

CopperTubing

Size O.D.4

2300

6 1/88 1/8 -10 1/8

110140200250

450

7501000

550

70

600

500

150

400450

550

MAXIMUM LOAD

On Flat

1200

Pipe

225270

100125

300350

3 1/2

RATING (LBS)In Clevis

40456580

354060

Oper. Mult.

2 2 1/2Insulation ThicknessIron

Pipe

180

350

TABLE II "B" = gauge of sheet metal jacket

3/4 1 1 1/2

20 - 24

56 - 7

2 1/82 5/8 - 4 1/8

5 1/8

1/2 - 1 1/2

1/2

8 - 10

Size

12 - 18

Size

TABLE I

Hanger(b) (c)

Surface(a) (c)

2 1/2 - 4

3

2

MODEL A3000 Insulated Pipe Support

A3

Extra HeavyBottom Jacket

Features:

Compact Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Double thickness bottom jacket for added structural strength and abrasive wear resistance Copper tubing sizes available Other I.D.'s and/or O.D.'s available on request Clamps available (see G-series) Performance Test Results on File: Available upon request.

Material Data:

A3000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive.


Application:

Model A3000 is designed for use on: Hot Water Steam Cold Water Air Chilled Water Gas Dual Temperature Vacuum

Intended for installation on: Flat Surfaces . Pipe Rolls Band, ring or clevis pipe hanger


FRONEK GROUP

CATALOG PS-2004

PipeSize

1/23/41

1 1/41 1/2

2Hardware sold separately 2 1/2

33 1/2

456810121416182024


6 20 6 20 6 20 6 20 9 20 9 20 9 206 20 6 20 6 20 6 20 9 16 9 16 9 16

9 16 9 16 9 16 9 16 9 16 9 1612 16 12 16 12 16 12 16 12 16 12 1618 16 18 16 18 16 18 16 18 16 18 16

TABLE II "B" = gauge of sheet metal jacket (bottom jacket approx. 2 X ga. of top jacket)

12 - 18 12 1/820 - 24

6 - 7 6 1/88 - 10 8 1/8 -10 1/8

2 1/2 - 4 2 5/8 - 4 1/85 5 1/8

1/2 - 1 1/2 5/8 -1 5/82 2 1/8

3 1/2 4 TubingSize Size O.D.

1 1/2 2 2 1/2 3Pipe

To develop maximum load rating, use band, ring or clevis hanger with manufacturer'sload rating equal to or greater than values shown in Table I. TABLE I

1/2 3/4 1

Contact factory for other dimensions, temperatures, loads.

Available in all insulation thicknesses.To obtain load ratings for operating temperatures of 500oF and higher, multiply loadrating by factor "F" in Table III.

Iron Insulation Thickness Copper

700 2100775 2400

Divide "A" in Table II by 6 to find maximum allowable travel on pipe roll (+/- fromcentered position). 650 1900

600 1500625 A5000 1700

To develop maximum load rating, width of support surface should be at least 1/2 ofdimension "A" in Table II. 575 1300

500 800525 See 1100

300 270 375The load ratings represent average values obtained in accordance with acceptedmethods and are subject to normal manufacturing variations. Dimensions and ratingsare subject to change without notice.

400 475450 575

Note: For higher load ratings, see A5000, A9000.250 225 325200 180

155

TABLE III165 150 2201200 0.30140 125

275

120750 0.7580

1000 0.50110 100

50

500 0.9065 60 70

70 90

(b) (d) (c) (d)

Temp. Factor40 35 45Oper. Mult.

40

(a) (d)

oF "F"45

Surface Roll or ClevisHanger

MAXIMUM LOADRATING (LBS)

On Flat On Pipe In Ring

A4

MODEL A4000 Insulated Pipe Support Extra Heavy BottomJacket w/ext. Insulation

Material Data:

A4000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive.


Features: Compact Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Double thickness bottom jacket for added structural strength and abrasive wear

Minimizes heat-loss and/or condensation Calcium silicate insulation extends 1'' beyond the galvanized sheet metal jacket providing for an easier vapor barrier joint with the pipe Copper tubing sizes available Other I.D.'s and/or O.D.'s available on request Clamps available (see G-series)

Performance Test Results on File: Available upon request.

resistance

Application:


Intended for installation on: Flat Surfaces . Pipe Rolls Band, ring or clevis pipe hanger


FRONEK GROUP

CATALOG PS-2004

PipeSize

1/23/41

1 1/41 1/2

2Hardware sold separately 2 1/2

33 1/2

456810121416

182024


6 20 6 20 6 20 6 20 9 20 9 20 9 206 20 6 20 6 20 6 20 9 16 9 16 9 16

9 16 9 16 9 16 9 16 9 16 9 1612 16 12 16 12 16 12 16 12 16 12 1618 16 18 16 18 16 18 16 18 16 18 16

3540

12 1/8

5/8-1 5/8

2 5/8 - 4 1/8

6 1/88 1/8 -10 1/8

See

270

6070100125

80110140165

Surface

404565

On Pipe In Ring

(c) (d)

or ClevisRoll

Temp.Oper. Mult.

Factor

12 - 18

2 1/2 - 4

TABLE III

2 2 1/2Iron PipeSize

1/2

21/2 - 1 1/2


3/4 1 1 1/2

20 - 24

56 - 78 - 10

220275200

250

150180225 325

1200

0.900.750.500.30

500"F"

7501000

oF 7090120155

MAXIMUM LOAD

On Flat

375475

45

Hanger(b) (d)

RATING (LBS)

(a) (d)

50

575

3 1/2

1700190021002400

4Insulation Thickness

700

300400450

650

500

625

525575600

5 1/8

CopperTubing

Size O.D.

1500

775

2 1/8

TABLE I

3

A6000

Note: For higher load ratings, see A6000, A9000

To obtain load ratings for operating temperatures of 500F and higher, multiply loadrating by factor "F" in Table III.


Available in all insulation thicknesses.



Divide "A" in Table II by 6 to find maximum allowable travel on pipe roll (+/- fromcentered position).

To develop maximum load rating use band, ring or clevis hanger with manufacturer'sload rating equal to or greater than values shown in Table I.

80011001300

A5

MODEL A5000 Insulated Pipe Support With loaddistribution plate

Features:

Compact Easy Installation Eliminates welding to pipe Copper tubing sizes available Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Load distribution plate integral with bottom jacket Other I.D.'s and/or O.D.'s available upon request


Material Data:

A5000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Load distribution Plate: Carbon steel

ASTM A-36 Coating: Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive.


Application:


Intended for installation on: Flat Surfaces Pipe Rolls


FRONEK GROUP

CATALOG PS-2004

A B C

9 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/412 9 3/812 9 3/812 9 1/212 9 1/212 9 1/212 9 3/412 9 3/412 9 3/412 9 3/4

Hardware sold separatelyNote: For higher load ratings, see A7000

The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturingvariations. Dimensions and ratings are subject to change without notice. Contact fac tory for current information.

To develop maximum load rating, width of support surface should be at least 1/2 of dimension "B" in Table I.To obtain load ratings for operating temperatures of 500 oF and higher, multiply maximum load rating by factor "F" in Table II.

Contact factory for other dimensions, temperatures, and loads. Available in all insulation thicknesses.1200 0.30

TABLE II

750 0.751000 0.50

1350 3500 0.90 TABLE I

oF "F" 42 1500

1350 3Temp. Factor 36 1500 1350 3Oper. Mult. 30 1500

24 1400 1250 320 1300 1150 318 1200 1075 316 1100 975 314 1000 900 312 925 825 310 650 575 28 625 550 26 500 450 25 450 400 24 350 315 2

3 1/2 300 270 23 250 225 2

2 1/2 200 180 2

Pipe Roll(a) (b) (b) +/-

Size Surface Roll on Pipe On Flat On Pipe (inches)

MAXIMUM LOAD Max. AxialRATING (LBS) Travel

With load distributionplate w/ext. InsulationMODEL A6000 Insulated Pipe Support

A6

Features:

Compact Easy Installation Eliminates welding to pipe Copper tubing sizes available Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Load distribution plate integral with bottom jacket Calcium silicate insulation extends 1'' beyond the galvanized sheet metal jacket providing for an easier vapor barrier joint with the pipe Other I.D.'s and/or O.D.'s available on request


Material Data:

A6000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant.Jackets: Galvanized Steel ASTM A-527.Load distribution Plate: Carbon steel

ASTM A-36 Coating : Primer coated or hot-dip galvanized.

Other coatings available upon request.Glue: Industrial contact adhesive


Application:


Intended for installation on: Flat Surfaces Pipe Rolls


FRONEK GROUP

CATALOG PS-2004

A B C

9 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/412 9 3/812 9 3/812 9 1/212 9 1/212 9 1/212 9 3/412 9 3/412 9 3/412 9 3/4


MAXIMUM LOAD Max. AxialRATING (LBS) Travel

Pipe On Flat On Pipe (inches)Size Surface Roll on

Pipe Roll(a) (b) (b) +/-

2 1/2 200 180 23 250 225 2

3 1/2 300 270 24 350 315 25 450 400 26 500 450 28 625 550 210 650 575 212 925 825 314 1000 900 316 1100 975 318 1200 1075 3

1250 320 1300 1150 3

30 150024 1400

1350 3Temp. Factor 36 1500 1350 3Oper. Mult.

1350 3500 0.90 TABLE I

oF "F" 42 1500

750 0.751000 0.50 Contact factory for other dimensions, temperatures, and loads . Available

in all insulation thicknesses.1200 0.30TABLE II

Note: For higher load ratings, see A7000

The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturingvariations. Dimensions and ratings are subject to change without notice. Contact factory for current information.

To develop maximum load rating, width of support surface should be at least 1/2 of dimension "B" in Table I.To obtain load ratings for operating temperatures of 500 oF and higher, multiply maximum load rating by factor "F" in Table II.

A7

MODEL A7000 Insulated Pipe Support Heavy Duty withload bearing plate

Features:

Compact Easy Installation Eliminates welding to pipe Copper tubing sizes available Minimizes heat-loss and/or condensation Insulating structural inserts for load transfer Overlapping galvanized sheet metal jacket Other I.D.'s and/or O.D.'s available on request Load distribution plate integral with bottom jacket


Material Data:

A7000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calcium silicate asbestos-free, treated with water

Load Distribution Plate: Carbon steel ASTM A-36 Coating: Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive.


repellant.

Application:


Intended for installation on: Flat Surfaces Pipe rolls, see A8200 Clevis hangers, see A9000


FRONEK GROUP

CATALOG PS-2004

A B C

6 3 1/46 3 1/46 3 1/46 3 1/46 3 1/46 3 1/46 3 1/49 6 3/89 6 3/89 6 3/89 6 1/29 6 1/29 6 1/29 6 3/49 6 3/49 6 3/49 6 3/4

Surface

350

Pipe (LBS)

(a)

3

TABLE I

MAXIMUMLOAD RTG.

2 1/2 250300

1850

8

3 1/2

2500

6

45

2000

400

101214 1650

500

16182024

25002500

3036

On FlatSize

The load ratings represent average values obtained in accordance with accepted test methods and are subject to normalmanufacturing variations. Dimensions and ratings are subject to change without notice. Contact factory for current information.

5507008751600

42

21002300

To develop maximum load rating, width of support sur face should be at least 1/2 of dimension "B" in Table I.

Contact factory for other dimensions, temperatures, and loads. Available in all

insulation thicknesses.


A8


Features:


Performance Test Results on File: Available upon request

Material Data:

A7200: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free,

treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calciumsilicate asbestos-free, treated with water

Load distribution Plate: Carbon steel ASTM A-36 Coating: Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive.


repellant.

Application:

Model A7200 is designed for use on: Hot Water Vacuum Gas Cold Water Steam Air Chilled Water Dual Temperature



FRONEK GROUP

CATALOG PS-2004

A B C

9 6 1/29 6 1/29 6 5/89 6 5/89 6 5/89 6 3/49 6 3/49 6 3/49 6 19 6 19 6 19 6 1

MAXIMUMLOAD RTG.

Pipe (LBS)Size On Flat

Surface(a)

6 10008 125010 155012 225014 278016 330018 360020 380024 410030 4500



TABLE I

36 450042 4500

Note: For higher load ratings, see A7400, B1100



A9


Features:



Material Data:

A7400: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calcium

silicate asbestos-free, treated with water

Load distribution Plate: Carbon steel ASTM A-36 Coating : Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive


repellant.

Application:




FRONEK GROUP

CATALOG PS-2004

A B C

9 6 3/49 6 3/49 6 3/49 6 19 6 19 6 19 6 19 6 1

MAXIMUMLOAD RTG.

Pipe (LBS)Size On Flat

Surface(a)

10 210012 340014 390016 440018 480020 510024 550030 5500

Table I



Note: For higher load ratings, see B1200



A10


Features:



Material Data:

A8000: Applicable PSI spec. doc. No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calcium silicate asbestos-free, treated with water repellant. Load Distribution Plate: Carbon steel ASTM A-36 Coating: Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive.


Application:




FRONEK GROUP

CATALOG PS-2004

A B C

9 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/49 6 1/412 9 3/812 9 3/812 9 3/812 9 1/212 9 1/212 9 1/212 9 3/412 9 3/412 9 3/412 9 3/4


MAXIMUM Max. AxialLOAD RTG. Travel

Pipe (LBS) (Inches)Size On on

Pipe Pipe RollRoll

2 1/2 225 23 250 2

3 1/2 300 24 350 25 450 26 500 28 625 210 875 412 1400 414 1475 416 1650 418 1800 420 1875 424 2050 4

436 2250 430 2250

4TABLE I

42 2250

Contact factory for other dimensions, temperatures , and loads. Available in all insulation thicknesses.



A11


Features:



Material Data:

A8200: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calcium silicate asbestos-free, treated with water repellant. Load distribution Plate: Carbon steel ASTM A-36 Coating: Primer coated or hot-dip galvanized. Other coatings available upon request. Glue: Industrial contact adhesive.


Application:


Intended for installation on: Pipe rolls Flat surface, see A7200 Clevis hangers, see A9000


FRONEK GROUP

CATALOG PS-2004

A B C

12 9 1/212 9 1/212 9 5/812 9 5/812 9 5/812 9 3/412 9 3/412 9 3/412 9 112 9 112 9 112 9 1

Hardware sold separatelyNote: For higher load ratings, see A8400, B1100


TABLE I

Contact factory for other dimensions, temperatures , and loads. Available in all insulation thicknesses.

36 4050 342 4050 3

24 3675 330 4050 3

18 3200 320 3375 3

14 2650 316 2950 3

10 1375 312 2550 3

6 900 38 1125 3

Pipe Pipe RollRoll



A12


Features:

Compact Easy Installation Eliminates welding to pipe Copper tubing sizes available Minimizes heat-loss and/or condensation Insulating structural inserts for load transfer Overlapping galvanized sheet metal jacket Other I.D.'s and/or O.D.'s Available on request Load distribution plate integral with bottom jacket


Material Data:

A8400: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts: High-density calcium silicate asbestos-free, treated with water

Load distribution Plate: Carbon steel ASTM A-36 Coating : Primer coated or hot-dip galvanized. Other coatings Available upon request. Glue: Industrial contact adhesive.


repellant.

Application:


Intended for installation on: Pipe rolls Flat surface, see A7400 Clevis hangers, see A9000

Note: Up to 1700F available upon request. Temperature Range: F to +1200F +40

FRONEK GROUP

CATALOG PS-2004

A B C

12 9 112 9 112 9 112 9 112 9 112 9 112 9 112 9 1




Pipe Pipe RollRoll

10 1875 2 1/412 3400 2 1/414 3500 2 1/416 3950 2 1/418 4300 2 1/420 4550 2 1/424 4950 2 1/430 5450 2 1/4

TABLE I



Note: For higher load ratings, see B1200


A13

MODEL A9000 Insulated Pipe Support Heavy Duty for usewith rod hangers

Features:

Compact Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Minimizes heat-loss and/or condensation Insulating structural inserts for load transfer Copper Tubing available Other I.D.'s and/or O.D.'s available on request


Material Data:

A9000: Applicable PSI spec. doc.: No. 205. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Structural Inserts : High-density calcium silicate asbestos-free, treated with water repellant. Glue: Industrial contact adhesive.


Application:


Intended for installation on: Band, ring or clevis pipe hangers Flat surfaces, see A7000 Pipe rolls, see A8000

Note: Up to 1700F available upon request. Temperature Range: F to +1200F +40

FRONEK GROUP

CATALOG PS-2004



6 20 6 20 6 20 6 20 9 20 9 20 9 206 20 6 20 6 20 6 20 9 16 9 16 9 16

9 16 9 16 9 16 9 16 9 16 9 1612 16 12 16 12 16 12 16 12 16 12 1618 16 18 16 18 16 18 16 18 16 18 1620 - 24


8 - 10 8 1/8 -10 1/812 - 18 12 1/8

5 5 1/86 - 7 6 1/8

5/8-1 5/82 2 1/8

2 1/2 - 4 2 5/8 - 4 1/8

1/2 3/4 1

1/2 - 1 1/2

3 1/2 4 TubingSize Size O.D.

1 1/2 2 2 1/2 3Pipe

TABLE I

Iron Insulation Thickness Copper


Available in all insulation thicknesses.To develop maximum load rating use band, ring or clevis hanger with manufacturer's loadrating equal to or greater than values shown in Table I.

20 240024 2750

Note: For higher load ratings, see D1000, D3000

The load ratings represent average values obtained in accordance with accepted methodsand are subject to normal manufacturing variations. Dimensions and ratings are subject to change without notice.

6 6008 900

1618

12001450

4 4005 550

3 3003 1/2 350

2 1752 1/2 250

1 1/4 1001 1/2 130

1/2 505580

3/41

or ClevisHanger

(a)

Size

MAXIMUM

(LBS)In RingPipe

LOAD RTG.

165019002150

101214

FRONEK GROUP

INTRODUCTION SECTION B

INTRODUCTION

SECTION B

PRE-INSULATED PIPE SUPPORTS - Base Mounted APPLICATION Heavy Industrial and Large HVAC Distribution Systems Features:

Accommodation of thermal movement Provision or lateral guide or restraint Minimization of side friction loads Wide range of maximum load requirements for each pipe size

In each model number series (for example: B1000 through B1300 Series), the higher the model number, the higher the load rating. Models B1000 - B1300 Sliding supports free to travel axially and laterally. Models B2000 - B2300 Same as B1000 - B1300 except can accommodate greater axial travel. Models B3000 - B3300 Sliding supports with lateral guides. Models B4000 - B4300 Same as B3000 - B3300 except can accommodate greater axial travel. Models B5000 - B5300 Same as B1000 - B1300 except can accommodate greater lateral travel. Models B6000 - B6300 Same as B2000 - B2300 except can accommodate greater lateral travel. Models B7000 - B7300 Same as B3000 - B3300 except with reduced vertical load ratings to

allow greater lateral loads. Minimum side friction is assured by the addition of lateral slide pads.

Models B8000 - B8300 Same as B4000 - B4300 except with reduced vertical load ratings to

allow greater lateral loads. Minimum side friction is assured by the addition of lateral slide pads.

To meet special thermal movement requirements, Pipe Shields Inc. has provided supports that have accommodated axial travels in excess of five (5) feet. By modifying our standard pipe support concept with combinations of structural insulation materials, steel base and strap design, and slide plate configuration, we can readily and economically respond to virtually any pipe support requirement.

If your requirements are not covered by the Product Data Sheets in this catalog, please contact us at 713-731-0030 or 1-800-787-5914.

Please acquaint yourself with the selection guide at the front of this catalog and the section index on the page following this introduction, for assistance in determining the most

appropriate support for your application.

FRONEK GROUP

CATALOG PS-2004

PIPESIZE LATERAL

MODEL RANGE AXIAL LATERAL GUIDE DUTY

B1000 1/2 - 42 1.5 1.5 NO MEDIUMB1100 1/2 - 42 1.5 1.5 NO HEAVYB1200 1/2 - 42 1.5 1.5 NO HEAVIERB1300 1/2 - 42 1.5 1.5 NO HEAVIEST

B2000 1/2 - 42 4.5 1.5 NO MEDIUMB2100 1/2 - 42 4.5 1.5 NO HEAVYB2200 1/2 - 42 4.5 1.5 NO HEAVIERB2300 1/2 - 42 4.5 1.5 NO HEAVIEST

B3000 1/2 - 42 1.5 0 YES MEDIUMB3100 1/2 - 42 1.5 0 YES HEAVYB3200 1/2 - 42 1.5 0 YES HEAVIERB3300 1/2 - 42 1.5 0 YES HEAVIEST

B4000 1/2 - 42 4.5 0 YES MEDIUMB4100 1/2 - 42 4.5 0 YES HEAVYB4200 1/2 - 42 4.5 0 YES HEAVIERB4300 1/2 - 42 4.5 0 YES HEAVIEST

PRE-INSULATED PIPE SUPPORTSHEAVY INDUSTRIAL - BASE MOUNTED

TRAVEL(INCHES) +/-

SECTION B INDEXFRONEK GROUP

CATALOG PS-2004

PIPESIZE LATERAL

MODEL RANGE AXIAL LATERAL GUIDE DUTY

B5000 1/2 - 42 1.5 1.5 - 4.5 NO MEDIUMB5100 1/2 - 42 1.5 1.5 - 4.5 NO HEAVYB5200 1/2 - 42 1.5 1.5 - 4.5 NO HEAVIERB5300 1/2 - 42 1.5 1.5 - 4.5 NO HEAVIEST

B6000 1/2 - 42 4.5 1.5 - 4.5 NO MEDIUMB6100 1/2 - 42 4.5 1.5 - 4.5 NO HEAVYB6200 1/2 - 42 4.5 1.5 - 4.5 NO HEAVIERB6300 1/2 - 42 4.5 1.5 - 4.5 NO HEAVIEST

B7000 1/2 - 42 1.5 0 W/SLIDE PADS MEDIUMB7100 1/2 - 42 1.5 0 W/SLIDE PADS HEAVYB7200 1/2 - 42 1.5 0 W/SLIDE PADS HEAVIERB7300 1/2 - 42 1.5 0 W/SLIDE PADS HEAVIEST

B8000 1/2 - 42 4.5 0 W/SLIDE PADS MEDIUMB8100 1/2 - 42 4.5 0 W/SLIDE PADS HEAVYB8200 1/2 - 42 4.5 0 W/SLIDE PADS HEAVIERB8300 1/2 - 42 4.5 0 W/SLIDE PADS HEAVIEST

PRE-INSULATED PIPE SUPPORTSHEAVY INDUSTRIAL - BASE MOUNTED

TRAVEL(INCHES) +/-

SECTION B INDEXFRONEK GROUP

CATALOG PS-2004

SECTION B INDEX

TO ORDER, specify:1. Quantity 202. Pipe Size & Type 18 IPS3. Insulation Thickness 24. Model Number B1000

EXAMPLE: (20) 18 x 2 B1000

FRONEK GROUP

CATALOG PS-2004

PIPESIZE 3 1/2 4 1/2 5 1/2 6 1/2

3 6 6 8 83 1/2 6 6 8 8

4 6 6 8 85 6 6 8 86 6 6 8 88 6 8 8 1010 6 8 8 1012 6 8 8 1014 6 8 8 1016 6 8 8 1018 6 8 8 1020 6 8 8 1024 6 8 8 1030 8 8 10 1036 8 8 10 1042 8 8 10 10

The Table above provides Bottom-of-Pipe to Top-of Steel dimensions ("B" dimensions) for3 1/2", 4 1/2", 5 1/2" and 6 1/2 " insulation thicknesses. Check with your salesperson if yourequire a "B" dimension other than those shown in this table.

INSULATION THICKNESS

THE FOLLOWING TABLE ILLUSTRATESBOTTOM-OF-PIPE TO TOP-OF STEEL DIMENSIONS

(DIMENSION "B") FOR "B" MODEL PIPE SUPPORTS AND "C" MODEL PIPE ANCHORSFOR INTERMEDIATE INSULATION THICKNESS

B1

Application:

Model B1000 is designed for use on: Hot Water Vacuum Gas Cold Water Steam Air Dual Temperature Chilled Water

Intended for installation on: Flat Surfaces

Temperature Range: +40F to +1200FNote: Up to 1700 F available upon request.

Features:

All pipe sizes Easy Installation Eliminates welding to pipe Overlapping galvanized sheet metal jacket Insulating structural inserts for load transfer Stainless steel to UHMW polyethylene slide Other I.D.'s and/or O.D.'s available on request Factory mounted polyethylene slide pad on steel mounting plate


Material Data:

B1000: Applicable PSI spec. doc.: No. 209. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive Structural Inserts: High-density calcium silicate asbestos free, treated with water repellant. Steel Straps/Base: Carbon Steel ASTM A-36. Fasteners: ASTM A-307 plated. Slide Pad: UHMW Polythylene (Teflon Optional). Coating: Primer coated or hot dipped galvanized. Other coatings available upon request.

Formal Submittal Sheets available.

Heavy Duty,Base Mounted MODEL B1000 Sliding Insulated Pipe Support FRONEK GROUP

CATALOG PS-2004

The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations.Dimensions and ratings are subject to change without notice.Note: For higher load ratings, see: B1100 - For greater axial travel, see: B2000 - For lateral restraint, see: B3000 - For lateral travel, see: B5000

Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 140 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 175 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.1251 225 4 2 3.875 4 2.5 4.875 4 3 5.937 4 4 7 6 4.5 8 6 6.5 10 8 8 12.25

1 1/2 325 4 2 4.375 4 2.5 5.5 4 4 7 4 4.5 8 6 5.5 9 6 7.5 11.25 8 9 13.252 375 4 2.5 5 4 3 6.0625 4 4 7 4 4.5 8 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 460 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 530 4 3 6.062 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 840 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 1050 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 4 7.5 11.375 6 8 12.375 6 9.5 14.875 8 11 16.8756 1275 4 5.5 9.25 4 6.5 10.25 4 7.5 11.375 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 1700 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 17.875 8 13 20.12510 2000 4 9 13.625 4 9.5 14.875 4 10.5 15.875 6 11 16.875 6 12 18.125 6 13 20.125 8 14.5 22.12512 2200 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 2500 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 2900 4 12.5 19.125 4 13 20.125 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 3200 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 3400 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 3600 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 4700 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 5500 4 26.5 39.625 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 6200 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125

Contact factory for other dimensional, temperature, load, or axial travel, requirements.

Insul. Thk. = 3" Insul. Thk. =4" Insul. Thk. = 5"Insul. Thk. = 1" Insul. Thk. = 1-1/2" Insul. Thk. = 2" Insul. Thk. = 2-1/2"

B2

Heavy Duty,Base Mounted MODEL B1100 Sliding Insulated Pipe Support

Application:




Features:



Material Data:

B1100: Applicable PSI spec. doc.: No. 209. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive Structural Inserts: High-density calcium silicate asbestos free, treated with water repellant. Steel Straps/Base: Carbon Steel ASTM A-36. Fasteners: ASTM A-307 plated. Slide Pad: UHMW Polythylene (Teflon Optional). Coating: Primer coated or hot dipped galvanized. Other coatings available upon request.


FRONEK GROUP

CATALOG PS-2004


Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 280 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 350 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.251 450 4 2 3.875 4 2.5 5 4 3 6.062 4 4 7 6 4.5 8 6 6.5 10 8 8 12.25

1 1/2 650 4 2 4.5 4 2.5 5.5 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.252 750 4 2.5 5 4 3 6.0625 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 920 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 1060 4 3 6.187 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 1680 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 2100 4 4.5 8.5 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 6 8 12.625 6 9.5 14.875 8 11 16.8756 2550 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 3400 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 18.125 8 13 20.12510 4000 4 9 13.875 4 9.5 15.125 4 10.5 16.125 6 11 17.125 6 12 18.125 6 13 20.125 8 14.5 22.12512 4400 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 5000 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 5800 4 12.5 19.375 4 13 20.375 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 6400 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 6800 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 7200 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 9400 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 11000 4 26.5 40.125 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 12400 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125



B3


Application:




Features:



Material Data:

B1200: Applicable PSI spec. doc.: No. 209. Insulation: Calcium Silicate asbestos-free, treated with water repellant. Jackets: Galvanized Steel ASTM A-527. Glue: Industrial contact adhesive Structural Inserts: High-density calcium silicate asbestos free, treated with water repellant. Steel Straps/Base: Carbon Steel ASTM A-36. Fasteners: ASTM A-307 plated. Slide Pad: UHMW Polyethylene (Teflon Optional). Coating: Primer coated or hot dipped galvanized. Other coatings available upon request.


FRONEK GROUP

CATALOG PS-2004



Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 400 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 500 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.251 650 4 2 4 4 2.5 5 4 3 6.062 4 4 7.125 6 4.5 8.125 6 6.5 10.125 8 8 12.25

1 1/2 950 4 2 4.5 4 2.5 5.5 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.252 1100 4 2.5 5 4 3 6.1875 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 1350 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 1600 4 3 6.187 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 2500 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 3100 4 4.5 8.5 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 6 8 12.625 6 9.5 14.875 8 11 16.8756 3800 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 5100 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 18.125 8 13 20.12510 6000 4 9 13.875 4 9.5 15.125 4 10.5 16.125 6 11 17.125 6 12 18.125 6 13 20.125 8 14.5 22.12512 6600 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 7500 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 8700 4 12.5 19.375 4 13 20.375 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 9600 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 10200 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 10800 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 14100 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 16500 4 26.5 40.125 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 18600 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125


B4


Application:




Features:



Material Data:



FRONEK GROUP

CATALOG PS-2004


The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations.Dimensions and ratings are subject to change without notice.Note: For greater axial travel, see: B2300 - For lateral restraint, see: B3300 - For lateral travel, see: B5300

Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 550 4 1.5 3.375 4 2 4.5 4 2.5 5.5 4 4 7.125 6 4.5 8.125 6 6.5 10.125 8 8 12.25 3/4 700 4 1.5 3.375 4 2 4.5 4 2.5 5.5 4 4 7.125 6 4.5 8.125 6 6.5 10.125 8 8 12.251 900 4 2 4 4 2.5 5 4 3 6.062 4 4 7.125 6 4.5 8.125 6 6.5 10.125 8 8 12.25

1 1/2 1300 4 2 4.5 4 2.5 5.5 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.252 1500 4 2.5 5 4 3 6.0625 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 1800 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6253 2100 4 3 6.187 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 3350 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 4200 4 4.5 8.5 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 6 8 12.625 6 9.5 14.875 8 11 16.8756 5100 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 6800 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 18.125 8 13 20.12510 8000 4 9 13.875 4 9.5 15.125 4 10.5 16.125 6 11 17.125 6 12 18.125 6 13 20.125 8 14.5 22.12512 8800 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 10000 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 11600 4 12.5 19.375 4 13 20.375 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 12800 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 13600 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 14400 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 18800 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 22000 4 26.5 40.125 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 24800 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125


B5


Application:




Features:



Material Data:



FRONEK GROUP

CATALOG PS-2004


The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations.Dimensions and ratings are subject to change without notice.Note: For higher load ratings, see: B2100 - For lesser axial travel, see: B1000 - For lateral restraint, see: B4000 - For lateral travel, see: B6000

Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 140 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 175 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.1251 225 4 2 3.875 4 2.5 4.875 4 3 5.937 4 4 7 6 4.5 8 6 6.5 10 8 8 12.25

1 1/2 325 4 2 4.375 4 2.5 5.5 4 4 7 4 4.5 8 6 5.5 9 6 7.5 11.25 8 9 13.252 375 4 2.5 5 4 3 6.0625 4 4 7 4 4.5 8 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 460 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 530 4 3 6.062 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 840 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 1050 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 4 7.5 11.375 6 8 12.375 6 9.5 14.875 8 11 16.8756 1275 4 5.5 9.25 4 6.5 10.25 4 7.5 11.375 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 1700 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 17.875 8 13 20.12510 2000 4 9 13.625 4 9.5 14.875 4 10.5 15.875 6 11 16.875 6 12 18.125 6 13 20.125 8 14.5 22.12512 2200 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 2500 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 2900 4 12.5 19.125 4 13 20.125 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 3200 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 3400 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 3600 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 4700 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 5500 4 26.5 39.625 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 6200 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125


B6


Application:




Features:



Material Data:



FRONEK GROUP

CATALOG PS-2004



Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 280 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 350 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.251 450 4 2 3.875 4 2.5 5 4 3 6.062 4 4 7 6 4.5 8 6 6.5 10 8 8 12.25

1 1/2 650 4 2 4.5 4 2.5 5.5 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.252 750 4 2.5 5 4 3 6.0625 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 920 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 1060 4 3 6.187 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 1680 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 2100 4 4.5 8.5 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 6 8 12.625 6 9.5 14.875 8 11 16.8756 2550 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 3400 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 18.125 8 13 20.12510 4000 4 9 13.875 4 9.5 15.125 4 10.5 16.125 6 11 17.125 6 12 18.125 6 13 20.125 8 14.5 22.12512 4400 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 5000 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 5800 4 12.5 19.375 4 13 20.375 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 6400 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 6800 4 15.5 23.375 4 16 24.375 6 16.5 25.375 6 17.5 26.375 6 18 27.375 8 19.5 29.375 8 21 31.37524 7200 4 18 27.375 4 19 28.375 6 19.5 29.375 6 20.5 30.375 6 21 31.375 8 22.5 33.375 8 24 35.37530 9400 4 22.5 33.625 6 23 34.625 6 24 35.625 6 24.5 36.625 6 25 37.625 8 26.5 39.625 8 28 41.62536 11000 4 26.5 40.125 6 27.5 41.125 6 28 42.125 6 28.5 43.125 6 29.5 44.125 8 31 46.125 8 32.5 48.12542 12400 4 31 46.125 6 31.5 47.125 6 32.5 48.125 6 33 49.125 6 33.5 50.125 8 35 52.125 8 36.5 54.125


B7


Application:




Features:



Material Data:



FRONEK GROUP

CATALOG PS-2004



Pipe Vert.Size Load B C E B C E B C E B C E B C E B C E B C E 1/2 400 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.125 3/4 500 4 1.5 3.25 4 2 4.375 4 2.5 5.375 4 4 7 6 4.5 8 6 6.5 10 8 8 12.251 650 4 2 4 4 2.5 5 4 3 6.062 4 4 7.125 6 4.5 8.125 6 6.5 10.125 8 8 12.25

1 1/2 950 4 2 4.5 4 2.5 5.5 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.252 1100 4 2.5 5 4 3 6.1875 4 4 7.125 4 4.5 8.125 6 5.5 9.125 6 7.5 11.25 8 9 13.25

2 1/2 1350 4 2.5 5.5 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.25 8 9.5 14.53 1600 4 3 6.187 4 4 7.125 4 4.5 8.125 4 5.5 9.125 6 6.5 10.125 6 8 12.375 8 9.5 14.6254 2500 4 4 7.25 4 4.5 8.25 4 5.5 9.25 4 6.5 10.25 6 7.5 11.375 6 9 13.375 8 10.5 15.6255 3100 4 4.5 8.5 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 6 8 12.625 6 9.5 14.875 8 11 16.8756 3800 4 5.5 9.5 4 6.5 10.5 4 7.5 11.625 4 8 12.625 6 9 13.625 6 10.5 15.875 8 12 17.8758 5100 4 7.5 11.625 4 8 12.625 4 9 13.625 6 9.5 14.875 6 10.5 15.875 6 12 18.125 8 13 20.12510 6000 4 9 13.875 4 9.5 15.125 4 10.5 16.125 6 11 17.125 6 12 18.125 6 13 20.125 8 14.5 22.12512 6600 4 10.5 16.125 4 11 17.125 4 12 18.125 6 12.5 19.125 6 13 20.125 6 14.5 22.125 8 16 24.12514 7500 4 11 17.125 4 12 18.125 4 12.5 19.125 6 13 20.125 6 14 21.125 6 15.5 23.125 8 16.5 25.12516 8700 4 12.5 19.375 4 13 20.375 6 14 21.375 6 14.5 22.375 6 15.5 23.375 8 16.5 25.375 8 18 27.37518 9600 4 14 21.375 4 14.5 22.375 6 15.5 23.375 6 16 24.375 6 16.5 25.375 8 18 27.375 8 19.5 29.37520 10200 4 15.

Catalogo Soportes Tuberia Aislada

Documents

Transcript of Catalogo Soportes Tuberia Aislada