8/9/2019 camara vivotek IP7134(TC5333)

1/8

8/9/2019 camara vivotek IP7134(TC5333)

2/8

EN - 1

English

Power off the Network Camera as

soon as it is found smoking or smelt

unusual.

Contact your distributor when such cases

happen.

Keep the Network Camera away from

the water. If the Network Camera is

wet, power off immediately.

Do not place the Network Cameraaround the heat sources, such as

television or oven.

Refer to your user's manual for theoperating temperature.

Keep the Network Camera away from

direct sunlight.

Do not place the Network Camera in

high humid environments.

Contact your distributor when such cases

happen.

Warning Before Install

8/9/2019 camara vivotek IP7134(TC5333)

3/8

EN - 2

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

when it's lightening.

Do not disassemble the Network

Camera.

Do not drop the Network Camera.

Do not insert any object into the

Network Camera, such as needles.

8/9/2019 camara vivotek IP7134(TC5333)

4/8

EN - 3

English

Camera stand

IP7133 / IP7134

Warranty card

Screws

Quick installation guide

Power adapter

P

Package Contents1

Software CD

8/9/2019 camara vivotek IP7134(TC5333)

5/8

EN - 4

Network Deployment3

Physical Description2

Front panel

Back panel

Status LEDP Privacy button

Lens

Built-in Microphone

ETHERNET

RESET

IO1 2 3 4

General I/O

terminal blockIndented reset button

Power cord socketEthernet 10/100RJ45 socket

POWERCOLLISION

LINK

RECEIVE

PARTITION

12 3 4 5

3. Connect the supplied power cablefrom the camera to a power outlet.

2. Connect the camera to a switchvia Ethernet cable.

Use Catagory 5 Cross Cablewhen Network Camera is directlyconnected to PC.

1. If you have external devices such as sensors and alarms,make connection from general I/O terminal block.

1: Power

2: Digital output3: Digital input

4: Ground

8/9/2019 camara vivotek IP7134(TC5333)

6/8

EN - 5

English

MAC:0002D1533318

Assembled from tested componentsComplete system not testedFCC ID: RRK2005100093

!IP7133

1. Install the "Installation Wizard 2" under the Software Utility directory from software CD.

2. The program will conduct analyses on your network environment. After your network is

analyzed, please click on the "Next" button to continue the program.

3. The program will search the VIVOTEK Network Devices in the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matches theone labeled on the bottom of your device to connect the Internet Explorer to the NetworkCamera.

0002D1533318

Installation

Wizard 2

Assigning IP Address4

5. Retrieve live video through web browsers or recording software.

8/9/2019 camara vivotek IP7134(TC5333)

7/8

EN - 6

For further setup, please refer to user's manual on the software CD.

Configure the Wireless Connection (IP7134 only)5

1. Check the SSID currently set on your wireless access point (AP).

2. Go to IP7134's Configuration > Wireless LAN.

3. Type in the SSID consistent with the setting on your AP.4. Select the Wireless mode as "Infrastructure".

5. Click Save. The Network Camera starts to reboot.

POWERCOLLISION

LINK

RECEIVE

PARTITION

1 2 3 4 5

ADSL/Cable

/Hub

AP

6. Wait for the live image is reloaded to your browser. Then, unplug the power cable and

Ethernet cable from the Network Camera.7. Replug the power cable to the camera. The Network Camera now operates in wireless

mode.

Note:

1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wirelessnetwork. The IP7134's factory SSID setting is set to "default".

2. Select "Ad-Hoc" wireless mode if you want the IP7134 to communicate without using anAP or wireless router.

8/9/2019 camara vivotek IP7134(TC5333)

8/8

P/N:625007400G