8/9/2019 camara vivotek IP7153

1/12

8/9/2019 camara vivotek IP7153

2/12

EN - 1

English

Contact your distributor in the event of

occurrence.

Keep the Network Camera away fromwater. If the Network Camera becomes

wet, power off immediately.

Refer to your users manual for the

operating temperature.

Power off the Network Camera assoon as smoke or unusual odors

are detected.

Do not place the Network Camera

around heat sources, such as a

television or oven.

Keep the Network Camera away

from direct sunlight.

Do not place the Network Camera in

high humidity environments.

Contact your distributor in the event of

occurrence.

Warning Before Installation

8/9/2019 camara vivotek IP7153

3/12

EN - 2

Do not place the Network Cameraon unsteady surfaces.

Do not touch the Network Cameraduring a lightning storm.

Do not disassemble the Network

Camera.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

8/9/2019 camara vivotek IP7153

4/12

EN - 3

English

Camera Stand Lens

IP7153 / IP7154

Warranty Card

Power Adapter

Quick Installation Guide Software CD

1 Check Package Contents

Antenna (IP7154 only)

ST7501Central ManagementSoftware

8/9/2019 camara vivotek IP7153

5/12

EN - 4

Power Cord SocketEthernet 10/100

RJ45 Socket

Recessed Reset ButtonGeneral I/OTerminal Block

Audio OutMicrophone In

External/InternalMicrophone Switch

Front Panel

Back Panel

Lens

Focus Controller

Zoom Controller

2 Physical Description

Built-in MicrophoneLight Sensor

Status LED

Antenna(IP7154 only)

Antenna(IP7154 only)

8/9/2019 camara vivotek IP7153

6/12

EN - 5

English

For further setup, please refer to the lens' instruction manual inside the

lens package.

1. Mount the lens by turning it clockwise onto the camera mount until it stops. Ifnecessary, turn the lens counterclockwise slowly to achieve the best optimumspacing.

2. Connect the lens cable plug to the camera connector.

3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten thezoom controller.

4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten thefocus controller.

W

N

T

1

2

4

3

3 Mounting the Lens to the Camera

8/9/2019 camara vivotek IP7153

7/12

EN - 6

General Connection (without PoE)1. Connect the camera to a switch via Ethernet cable.

2. Connect the power cable from the Network Camera to a power outlet.

POWERCOLLISION

LINK

RECEIVE

PARTITION1 2 3 4 5

1

2

Ethernet Switch

4 Network Deployment

8/9/2019 camara vivotek IP7153

8/12

EN - 7

English

Power over Ethernet (PoE) (IP7153 only)

POWERCOLLISION

LINK

RECEIVEPARTITION

1 23 4

5

PoE Switch

POWERCOLLISION

LINK

RECEIVEPARTITION

12 3 4 5

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and anon-PoE switch.

Non-PoE Switch

PoE Power Injector

(optional)

When using a PoE-enabled switch

This Network Camera is PoE-compliant, allowing transmission of power and data via

a single Ethernet cable. Follow the below illustration to connect the Network Camera

to a PoE-enabled switch via Ethernet cable.

8/9/2019 camara vivotek IP7153

9/12

EN - 8

This device complies with part 15 of the FCC rules. Operation is subject tothe following two conditions:(1)This device may not cause harmful interference, and(2) this device must accept any interference received, including interferencethat may cause undesired operation.

RoHS

Network Camera

Model No:IP7153

Pat. 6,930,709 Made in Taiwan

MAC:0002D1070417

1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.2. The program will conduct an analysis of your network environment. After your network

is analyzed, please click on the "Next" button to continue the program.

3. The program will search for VIVOTEK Video Receivers, Video Servers, and NetworkCameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matchesthe one labeled on the bottom of your device to connect to the Network Camera viaInternet Explorer.

00-02-D1-07-04-17 192.168.0.219 IP7153

Installation

Wizard 2

5 Assigning an IP Address

0002D1070417

8/9/2019 camara vivotek IP7153

10/12

EN - 9

English

For further setup, please refer to user's manual on the software CD.

6 Ready to Use

1. Access the Network Camera on the LAN.2. Retrieve live video through the web browser or recording software.

8/9/2019 camara vivotek IP7153

11/12

EN - 10

7 Configure the Wireless Connection (IP7154 only)

1. Check the SSID for your wireless access point (AP).2. Go to the IP7154 Configuration page > Advanced mode > Wireless LAN.

Note:

1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wirelessnetwork. The IP7154 factory SSID setting is set to "default".

2. Select "Ad-Hoc" wireless mode if you want the IP7154 to communicate withoutusing an AP or wireless router.

POWER COLLISION

LINK

RECEIVE

PARTITION

12 3 4

5

ADSL/Cable

/Hub

AP

3. Type in the SSID the same asyour AP.

4. Select the Wireless mode as"Infrastructure".

5. Click Save. The NetworkCamera will reboot.

For further setup, please refer to the user's manual on the software CD.

6. Wait for the live image to be reloaded to yourbrowser. Then, unplug the power cable and Ethernetcable from the Network Camera.

7. Replug the power cable to the camera. The NetworkCamera will now operate in wireless mode.

8/9/2019 camara vivotek IP7153

12/12

P/ N: 625009000G Ver.1.01Co pyright 2009 VIVOTEK INC. All right reserved .