Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The...
-
Upload
christina-caldwell -
Category
Documents
-
view
216 -
download
0
Transcript of Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The...
![Page 1: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/1.jpg)
Bench Tools + (Metalwork)
![Page 2: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/2.jpg)
The 300mm rule is marked out in both Metric and Imperial sizes
Rule
The Rule is made from Stainless Steel
Metric Scale (mm)
Imperial Scale
(Inches)
![Page 3: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/3.jpg)
Odd Leg Callipers are used to draw a line parallel to an edge
Odd Leg Callipers
![Page 4: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/4.jpg)
A Scriber is used to mark out on metal
Scriber
![Page 5: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/5.jpg)
An Engineers square was used to mark lines at right angles to an edge.
Engineers square
![Page 6: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/6.jpg)
Each work station is equipped 4 files
1 Rough cut Rectangular File
1 Smooth cut Rectangular file
1 Half Round File
1 Round File
One edge of the file has no teeth. This is called the Safe Edge
Remember never use a file with a broken or missing handle.
Files
The part of the file inside the handle is called the Tang
![Page 7: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/7.jpg)
The Centre punch and Ball Pein Hammer are used to mark the centres of holes before drilling
Centre Punch is made from high carbon steel
Ball Pein Hammer
Ball Pein Hammer
Centre Punch
![Page 8: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/8.jpg)
Spring Dividers
Spring dividers are used to mark curves on metal.
To obtain the best results you should always Centre punch the middle of your curve before you try to use the dividers
![Page 9: Bench Tools + (Metalwork). The 300mm rule is marked out in both Metric and Imperial sizes Rule The Rule is made from Stainless Steel Metric Scale (mm)](https://reader030.fdocuments.net/reader030/viewer/2022032803/56649e395503460f94b2b564/html5/thumbnails/9.jpg)
The End