BC-2028 Manual

7/27/2019 BC-2028 Manual

1/50

BC-2028User Guide

Replication without approval from Our Company is forbidden.

Any operation for all products depends on actual operating status.Due to continuous product updates, we don't promise the actualproduct is the same as one presented in the document, neither bearwe any dispute arising from any inconsistence between actualoperation and those procedures described in the document.

7/27/2019 BC-2028 Manual

2/50

Contents

INTRODUCTION...................................................................................II1NECESSARY TO KNOW ..............................................................VII2BASIC CONCEPTS.............................................................................8

2.1.BASIC CONCEPTS...............................................................................8

2.1.1.User Enrollment........................................................................8

2.1.2.User Verification.......................................................................8

2.1.3.Match Threshold Levels............................................................8

2.1.4.User ID Numbers......................................................................92.1.5.Authority (status) Levels...........................................................9

2.1.6.Start-up window......................................................................10

2.2.HOWTOPLACETHEFINGER............................................................10

3ENROLLMENT AND VERIFICATION PROCEDURES.............113.1.ENROLLING USERS..........................................................................12

3.1.1.Fingerprint Enrollment...........................................................13

3.1.2.Password Enrollment..............................................................14

3.1.3.Fingerprint & Password.........................................................153.2.TESTINGAN ENROLLMENT..............................................................18

3.3.ENROLLINGA USERWITHTHE DISPLAY FINGEROPTION ON.........18

3.4.VERIFYING YOURIDENTITY............................................................18

3.4.1.Fingerprint Verification..........................................................18

3.4.2.Password Verification.............................................................19

3.4.3.Password & Fingerprint.........................................................19

3.4.4.EM card enrollment ..............................................................20

3.4.5.EM card & Fingerprint...........................................................203.5.HINTSFORSUCCESSFUL ENROLLMENTS.........................................20

4SYSTEM SETUP................................................................................234.1.SYSTEM SETUP................................................................................24

4.1.1.Date Time................................................................................24

4.1.2.Language.................................................................................24

4.1.3.Format.....................................................................................25

4.1.4.Advanced Options...................................................................25

4.2.COMMUNICATION OPTIONS.............................................................274.3.LOG SETUP......................................................................................28

I

7/27/2019 BC-2028 Manual

3/50

User Guide

4.4.LOCKSET........................................................................................29

5SYSTEM INFORMATION...............................................................316TROUBLE SHOOTING....................................................................327USER ACC OPTS GUIDE................................................................33

7.1.PRODUCT FEATURES........................................................................33

7.2.BASIC CONCEPTS.............................................................................33

7.3.ACCESS OPTIONS.............................................................................34

7.3.1.Brief Introduction to Access Options .....................................35

7.3.2.Verification Flow of Access Options ......................................36

7.4.FUNCTION DESCRIPTION.................................................................387.4.1.Definition of Time zone...........................................................38

7.4.2.Definition of Grouping Function.............................................40

7.4.3.User Acc Opts .........................................................................42

7.4.4.Access Comb...........................................................................45

TECHNICALSPECIFICATIONS..................................................................49

IntroductionIn this chapter, details of the common terms and the finger

print press manner are presented.BC-2028 Fingerprint Access Control System

II

7/27/2019 BC-2028 Manual

4/50

OK Confirm key: confirm your current present operation;M Enter the management interface in the initial status;C Cancel your present operation

Scrolling up key: Scrolling up the menu Scrolling up key: Scrolling down the menu

Door bell;

Control the power on and off. Or digital 0

Number keys: Input number 0-9

BC-2028 is a simplified-designed terminal unit fingerprintAccess controller, and use easy,. It can be assembled on thesensitive area need authority to access; Be comminuted with thehigh-safe fingerprint identification system and advance AccessControl management creatively, so that come true high-safemanagement of in-out control.

Port description

III

7/27/2019 BC-2028 Manual

5/50

User Guide

J9lead foot Color function declaration

RS485- blue RS485communication -

IV

7/27/2019 BC-2028 Manual

6/50

RS485+ orange RS485communication +

GND black RS485communication GND

RS232T yellow RS232 TXD(NC)

RS232R purple RS232 RXD(NC)

GND black RS232communication GND

DS-IN brown Door Contact+

OPEN gray Open key+

J10lead foot Color function declarationCOM orange electric relaycommon terminalNC purple electric relayNC

NO blue electric relayNOVG-OUT1 green VG out export D0

VG-OUT2 white VG out export D1

GND black VG communication GND

BELL1 red BELL 1

BELL2 brown BELL 2

ALARM1 yellow Warning 1

ALARM2 gray warning2

V

7/27/2019 BC-2028 Manual

7/50

User Guide

VI

7/27/2019 BC-2028 Manual

8/50

.Installation drawing

1

Necessary to knowPlease do not place the product in the place with strong light,because the strong light may significantly affect the finger printscanning, and thus cause the print verification fail.

Try to avoid using outdoor, the working temperature range ofthe attendance machine is 0-400C. Usage outdoor of long period, inaddition to the internal heat of the machine, will cause problem tothe operation, including the decrease of the reaction and thepassing rate. If outdoor usage can not be avoided, it is suggested touse sun umbrella and cooling facility.

VII

7/27/2019 BC-2028 Manual

9/50

User Guide

2 Basic Concepts2.1. Basic Concepts

This section contains definitions and descriptions ofFingerprint T&A Concepts including: User Enrollment

.User Verification

Match Threshold Levels

User ID Numbers

Authority (Status) Levels

The two most important Fingerprint T&A Functions areuser enrollment and user verification.

2.1.1. User EnrollmentEnrollment is the process of create an ID number and

scanning a users finger to create a template three times. Thistemplate is associated with a user ID number and stored.

During user verification, the stored template is compared tothe current fingerprint scan to confirm the users identity.

Enrollment is performed at designated units. The user can

verify on the time recorder that enroll his fingerprint. Theenrollment process takes approximately 1 second.

Up to 3 fingers can be enrolled for the same ID number, sothe user may have more verifications way.

Ideally, it is better to enroll more than one finger for backup sothat if the user injures the enrolled finger have an alternate fingertemplate is available. While recording the finger type is optional, it isrecommended such as left or right index, so that at verification the

user is prompted as to which finger to use.

2.1.2. User VerificationVerification ways: You can use F/P/C, P, C, F+P, F+CF

Finger, P: Password C: EM card . You can use this waysverification your enrollment message is successful or fail.

2.1.3. Match Threshold Levels

The Mach Threshold is a number that represents thedegree to which verification is examined to ensure that the

8

7/27/2019 BC-2028 Manual

10/50

person is the person claimed.The Match Threshold Levels establishes a balance

between False Acceptance Rate (FAR) and False RejectionRate (FRR). FAR measures how often a non-authorized user isfalsely recognized and granted access to the system. FRRmeasures how often an enrolled and authorized user, whoshould be granted access to the system, is denied on the basisthat the system did not recognize him.

You can set match threshold levels on a per-use basis. Forthe fingerprint verification is difficult, you can adopt ID &Fingerprint verification (match one to one).

Raising the threshold increases security, while lowering itincreases throughout. The correct balance is essential.

For users with worn or damaged fingers, match thresholdlevels can (and should) be reduced.

Different sites have different requirements.

Table 11 Suggested Match Threshold Settings

FRR FAR

Match Threshold Settings

1N 11High Low 4 40-50

Middle Middle 3 20-40Low High 1-2 0-20

2.1.4. User ID NumbersBefore beginning fingerprint enrollment, a user is assigned

User ID Number. This ID number is used to call up thefingerprint template each time that verification is requested.

ID numbers are normally called up via the keypad, but theycan be called up through other means such as RF Card.

2.1.5. Authority (status) LevelsFingerprint T&A has four authority or status levels:

Users are people whose identity must be verified,such to gain access to a facility or to have theirattendance recorded.

Enrollers are Users who are authorized to enroll new

9

7/27/2019 BC-2028 Manual

11/50

User Guide

users or delete on to the system.

Managers can do other operations, except set

advanced option and enroll managers authority. Supervisors are Users who access to all functionsand change all setup in the system.

Note: Without Manager and Supervisor status in the system, theEnroller will enroll them. And if there isnt a Supervisor in the system, theManager will enroll him.

2.1.6. Start-up windowWhen the machine is connected to the power source and

before the Power on button is pressed, the screen will display aso-called initial interface, as following:

2.2. How to place the finger

The correct way is:

Place a finger flatware on the sensor surface

Place it to the center of the sensor surface

The wrong way is:

10

Welcome 09:08:20

08-04-30 WED

7/27/2019 BC-2028 Manual

12/50

Note:Please adopt the correct way to place the finger;Our Company isnot responsible for the malfunctioning results arising from improper pressingmanners. Our company reserve ultimate the interpreting and modifying right

for this.

3 Enrollment and Verification ProceduresThis chapter describes how to enroll and verify users on

the Fingerprint T&A verification system.The following topics are included:

Enrolling User

Testing an Enrollment Enrolling a User with the Display Finger Option On

Verifying Your Identity

Hints for Successful Enrollments

Note: You must have Enroller, Manager, or Supervisorstatus to enroll users. For information on status levels, seeAuthority (Status) Levels on 1.1.5.

11

7/27/2019 BC-2028 Manual

13/50

User Guide

3.1. Enrolling UsersIf this is the first enrollment in a new or empty system,

everyone will become an enroller.If there is a manager in the system, you will have Manager

Status to enroll a new user.There are five ways of enrollment, fingerprint enrollment;

password enrollment, fingerprint & password, EM card,fingerprint & EM card. Fingerprint enrollment suited the mostpeople who have better quality fingerprints; Fingerprint &Password, EM card, fingerprint & EM card suite people whohavent the good fingerprint.

To start the enrollment process, identify yourself firstlypress [Menu], enter your ID number or fingerprint, and then verifyyour identity.

Note: If this is the first enrollment in a new or empty system, youwill not be prompted for verification.

The following message appears on the display:

Press Up or Down key, select what you need options:

Select Enrollment, Press OKthe following message display:

12

Menu

Enrollment

Menu

Setup

Menu

System Info

Enrollment

Manager

7/27/2019 BC-2028 Manual

14/50

Press Up or Down key select what you need options:

Select user, Press [OK], the following message display:

Press Up or Down key select what you need options:

3.1.1. Fingerprint Enrollment(1) Access the Finger Data to press [OK], the following display:

(2) Press [OK], the following appears:

13

Enrollment

UserEnrollment

Delete

User

Finger Data

User

Password

User

Fp + Pass

User

Card

User

Fp + Card

New Enroll

No-ESC Yes-OK

New Enroll

ID 0000008

7/27/2019 BC-2028 Manual

15/50

User Guide

(3) Input the enrolling number (the range is 1 to 9999999),press [OK], the following appears:

(4) If the test is successful three times in a row, the followingappears:

Note: 0000008-0The last number 0 meansthe first fingerprint.

Press [OK], the previous message continues to be displayedwhile the template is created.

If your identity cannot be verified, you are prompted to tryagain. And you must restart the verification procedure (step 3).

3.1.2. Password Enrollment(1) Access the password enrollment, press [OK], the following

appears:


(3) Input the enroll number (the range is 1 to 999999999),press [OK], the following appears:

14

Press Finger #1

0000008-0

Enroll OK

New Enroll

No-ESC Yes-OK

New Enroll

ID 0000002

New Enroll

PWDIn *******

7/27/2019 BC-2028 Manual

16/50

Note: The password range is 1 to 7.

(4) Input the password, press [OK], the following appears:

(5) Input the password again, presses [OK], the followingappears:

The previous message continues to be displayed whilethe template is created.

3.1.3. Fingerprint & PasswordAccess the Fp+& Pass, press [OK], the following appears:


(3) Input the id (range is 1 to 9999999), press [OK], thefollowing appears:

(4) If the test is successful three times in a row, thefollowing appears:

15

Note: 0000002-P

The last letter P means password.

New Enroll

Confm *******

0000002-P

Enroll OK

New Enroll

No-ESC Yes-OK

New Enroll

ID 0000003

Press Finger #1

7/27/2019 BC-2028 Manual

17/50

User Guide

(5) Input your password, the following appears:

(6) Input the passwords again, press [OK], the followingappears:

The previous message continues to be displayed while the

template is created.

4.1.4 EM card

(1) Access the EM card enrollment, press [OK], the followingappears:



Note: The password range is 1 to 7.

16

PWDIn *******

New Enroll

Confm *******

0000003-P

Enroll OK

New Enroll

No-ESC Yes-OK

New Enroll

ID 0000002

New Enroll

PWDIn *******

7/27/2019 BC-2028 Manual

18/50

(4) Then you can input the card, press [OK], the followingappears:

When you complete it, press [OK]. The previous messagecontinues to be displayed while the template is created.

4.1.4 EM card & Fingerprint(1) Access the EM card & Fingerprint enrollment, press [OK],

the following appears:



Note: The password range is 1 to 7.(4) When you enroll your finger you can input the EM card,

press [OK], the following appears:

The previous message continues to be displayed while the

template is created.

17

Card Inxxxxxxxxxx

New Enroll

No-ESC Yes-OK

New Enroll

ID 0000002

Card In

xxxxxxxxxx

Press Finger #1

7/27/2019 BC-2028 Manual

19/50

User Guide

3.2. Testing an Enrollment

Ask the users to place their finger to perform testverification. If the test was successful, you will adopt Fingerprintenrollment. If the poor quality of fingerprint, you will berecommended to use Fingerprint & Password.

3.3. Enrolling a User with the Display Finger Option OnPress [ESC] to the Display Dinger Option On, the following

appears:

Note: Where system memory permits, it is advisable tohave at least two fingers enrolled for a long-term user.

3.4. Verifying Your IdentityThe workers used Fingerprint T&A to verify their identity.

The system defaults to three ways of verification: Fingerprint

verification, Password verification, ID number & Fingerprint. Thefollowing appears:

3.4.1. Fingerprint VerificationPlace the finger on the sensor surface, the following

appears:

It continues for about 0.5 seconds.

If the test is successful, it will say Thank you, thefollowing appears:

If your identity cannot be verified, you are prompted to try

18

New Enroll

No-ESC Yes-OK

Backup

ID 0000003

Fp Verify

Take off !

ID 0000008

Verify OK !

7/27/2019 BC-2028 Manual

20/50

again, the following appears:

It continues for about 0.5 seconds, return to the start-upwindow.

3.4.2. Password VerificationTo start the enrollment process, enter your ID number, the

following appears:

Press [OK], the following appears:

Input correct password, press [OK], the following appears:

If the password cannot be verified, the following appears:

3.4.3. Password & FingerprintTo start the enrollment process, enter your ID number, the

following appears:

19

Fp VerifyAgain Inputf !

ID 3Esc-ESC Pwd-

Pass Verify

PWDIn *******

ID 0000003

Verify OK !

Pass Verify

Again Inputf !

ID 8Esc-ESC Pwd-

7/27/2019 BC-2028 Manual

21/50

User Guide

Press your finger,

If your identity is verified, the following appears:

3.4.4. EM card enrollmentTo start the enrollment process, touch your EM card, if your ID is

verified, the following appears:

3.4.5. EM card & FingerprintTo start the enrollment process, touch your EM card or enter your

finger, if your identity is verified, the following appears:

3.5. Hints for Successful Enrollments

The fingerprint is of good quality, the verification speed willfast; otherwise, it will verify slowly or occur to FRR.

20

1:1 Fp Verify

Take off

ID 0000008

Verify OK

ID xxxxxx

Verify Ok

Fp Verify

Take off !

ID xxxxxx

Verify Ok

7/27/2019 BC-2028 Manual

22/50

In order to improve the fingerprint verification quality, thefollowing hint appears:

Figure Error: Reference source not found-1Enrolled unsuccessfulor the fingerprint of poor quality:

Dry or dirtyfingerprints

Solve the dry problems that rub thedry finger and palm.

If the fingerprint is dry, you will adoptthe way of wetting up the finger, suchas ah-ah.

Have no enough to

bring pressure

The user should place a finger firmly

and squarely on the sensor surface.

How to select thefinger?

Recommend to left or right index ormiddle finger.

Use fingerprints of good quality,without worn or hurt.

The user usually selects theforefinger, if it was of a poor quality, youwill be recommended to middle finger

or ring finger.If the users finger is less, you will

select the thumb.

How to place thefinger?

Place your finger firmly and touch thesensor surface must be over 2/3.

The fingerprint does not touch uprighton the sensor surface.

Do not touch the finger too fast; Do

not move the finger on the sensorsurface.

The influence of thefingerprints change

For users with worn or damagedfingers, the identification can beinfluenced.

If the finger quality was poor, you willselect password verification.

21

7/27/2019 BC-2028 Manual

23/50

User Guide

Others

However, few peoples fingerprintquality is too poor to verify thefingerprint in gear. Please use ID &fingerprint verification, and the MatchThreshold Levels can be reduced oruse password verification.

22

7/27/2019 BC-2028 Manual

24/50

4 System Setup

Press MENU key in the initial interface, and the systemmay identify the proper right of the user, and then the screenshall display the following information:

Press Up or Down key, select Setup

Choose the setup, enter the next step, then the followinginformation will be displayed:

In the setup options, there are six choices: system setup,communication setup, log setup, door lock function setup. Nowwe introduce these one by one.

MenuSetup

Menu

Enrollment

Setup

Log Setup

Setup

System

Setup

Communication

Setup

Lock set

23

7/27/2019 BC-2028 Manual

25/50

User Guide

4.1. System SetupAccess System , the following appears:

The setup facility covers four areas: Date Time, Language,

and Advanced Options.

4.1.1. Date TimeAccess Date Time, the following appears:

To change the date press Up and Down Key , or input thecorrect date and time valuer, press [OK] to change your selecte,press [ESC] the following appears

4.1.2. Language

Select the wanted language and press OK. The defaultlanguage is simplified Chinese, the screen shall display

System

Time

System

Language ENGLISH

SystemDateFormat Y-M-D

System

SuperSet

2008-04-29

94756 WED

Save?

NO-ESC Yes-OK

24

7/27/2019 BC-2028 Manual

26/50

Chinese.

Press the up and down key to choose the language. Theattendance supports three languages: simplified Chinese, traditionalChinese, and English. On the screen, these may be displayed assimplified, traditional, and ENG respectively.

Choose the wanted language, and press OK. Then press ESCto exit the system setup. The system may indicate you to save the

change. You may press OK to confirm and change the systemlanguage setup.

Traditional Chinese Simplified Chinese

4.1.3. FormatPress UP or Down, select Fmt, Press OK, and modify Fmt,

There are four formats Y-M-

DY/M/DY.M.DD.M.YD/M/YD-M-Y M.D.YM/D/YM-D-Y. It will modify date format on original interface

For example: Y/M/D is left figureY-M-D is right figure:

4.1.4. Advanced Options

Access SuperSet Option, press [OK], the followingappears:

System

Language ENGLISH

System

DateFormat Y-M-D

Welcome 173708/04/30 WED

Welcome 173708-02-18 WED

25

7/27/2019 BC-2028 Manual

27/50

User Guide

Press UP or Down key select option, all display as follows

Press Up and Down Key to scroll up or down the screen toselect the option.

Default:: restore all setup information to defaultAll Log Delete: delete all logs of flash disk.

System

Default

System

All Log Delete

System

All Datele

System

Cancel Manager

System

1:N Level 3

System

Init 1:1 40

System

VoiceOut No

System

Managers 5

26

7/27/2019 BC-2028 Manual

28/50

All Delete: delete all enrolling fingerprints and logs.Cancel Manager: change the managers rights into ordinary

users rights.1:N Levels: For helping in selecting threshold level settings,

see Table 3.1.3.1 to 1Whetherinput the staff ID No.;1:1 Threshold Levels: ID+ Fingerprint identification and

degree of register template matching, Please see Table 3.1.3VoiceOut: Whether use to phonic hint or not.Managers Max managers rights into ordinary users count.

4.2. Communication OptionsEnter the communication menu; the screen shall display

the following information:

CommunicationBaudrate 38400

Communication

Device ID 1

Communication

Parity None

Communication

Port NO 5005

Communication

Password 200409

Communication

Stopbit 1

27

7/27/2019 BC-2028 Manual

29/50

User Guide

Device ID: the number of the machine, ranged from 1-255Baud rate: the communication speed of the

communication with the computer. There are three choices:9600, 38400,115200. High speed communication is fast, andthe RS232 communication is recommended. Low speedcommunication is slow, RS485 communication is

recommended.IP address: By default, the IP is 192.168.1.201. You may

change according to practical requirement.Port No: By default is 5005 . Work with IP Address.Subnet mask: By default is 255.255.255.0.Default gateway: By default is 192.168.0.1.Password: the system default communication password is

200409, which may be defined

Warning: RS485 communication in the outdoorenvironment, the lightening protection device is required.

4.3. Log SetupAccess Log Opt, the following message appears:

Log Setup

M-Log Wrn No

Communication

IP Address

Communication

Subnet mask

Communication

Default gateway

28

7/27/2019 BC-2028 Manual

30/50

Alarm Attendance Log: when the remainder log capacity

reached set numerical value, it will automatically sound awarning that logs were filled.

Recheck Minute: Set within compass (Unit: minute). Someonesenrollment has enrolled, then, the log twice was not displayed in thesystem.

4.4. Lock SetEnter the Lock Set menu; the screen shall display the

following information:

Log SetupW-Log Wrn 1000

Log Setup

Re-Verify No

Lock Set

Define TZ

Lock Set

User Acc Opts

Lock Set

GRP TZ Define

Lock Set

GroupMatch

29

7/27/2019 BC-2028 Manual

31/50

User Guide

Five main functions in Access Options:Time Zone Define: indicate the door unlocked time in

every day of the week

User Access Options is to setup the unlock time andAccess Comb by the user;

GRP TZ Define is GRP TZ, time zone station the group;GroupMatch is to define variant unlock combinations,

every combination consists different groups;Unlock: Fingerprint startups lock time;

In this menu, the user can define the corresponding

functions.For details of the operation, please refer to the

Unlock

OpenTime 5

Lock SetUnlock

Unlock

Time 3

Lock Set

Alrm Release

Lock Set

Warn Time 1

30
http://var/www/apps/conversion/tmp/scratch_6/F4%E9%97%A8%E7%A6%81%E6%93%8D%E4%BD%9C%E6%8C%87%E5%8D%97%E8%8B%B1%E6%96%87.dochttp://var/www/apps/conversion/tmp/scratch_6/F4%E9%97%A8%E7%A6%81%E6%93%8D%E4%BD%9C%E6%8C%87%E5%8D%97%E8%8B%B1%E6%96%87.dochttp://var/www/apps/conversion/tmp/scratch_6/F4%E9%97%A8%E7%A6%81%E6%93%8D%E4%BD%9C%E6%8C%87%E5%8D%97%E8%8B%B1%E6%96%87.dochttp://var/www/apps/conversion/tmp/scratch_6/F4%E9%97%A8%E7%A6%81%E6%93%8D%E4%BD%9C%E6%8C%87%E5%8D%97%E8%8B%B1%E6%96%87.dochttp://var/www/apps/conversion/tmp/scratch_6/F4%E9%97%A8%E7%A6%81%E6%93%8D%E4%BD%9C%E6%8C%87%E5%8D%97%E8%8B%B1%E6%96%87.doc

7/27/2019 BC-2028 Manual

32/50

5 System Information

Access [Menu] to Sys Info, press [OK], the followingappears:

It is plays user numbers, password numbers, fingerprintnumbers, manager and log numbers in the screen.

System Info

User 3000

173

8046System Info

Manager 5

System Info

Work Log 800000

System Info

Mgr Log 0

System Info

Fingerprint 3000

System Info

Password 3000

31

7/27/2019 BC-2028 Manual

33/50

User Guide

6 Trouble shooting

1. CleaningFrom time to time, the optical platen, the keypad anddisplay window require cleaning. Since working environmentsdiffer, it is not possible to define when cleaning should beperformed. Following is guide:

Figure Error: Reference source not found-2 Cleaning Schedule

Item Cleaning Frequency

Keypad anddisplay window

Cleaning when visibly dirty and hardto read. See cleaning the keypad anddisplay below.

Optical platenDo not over clean. The platen is

designed to work under greasy or dirtyconditions.

However, do clean if the platen isobstructed or people are reportingdeteriorating performance. Seecleaning the Optical Platen below.

2. Cleaning the Keypad and DisplayTo clean the keypad and display, use the same cleaningproducts as for the platen, and wipe dry.

3. Cleaning the Optical PlatenClean the optical platen as follows:(1) If dusty or gritty, first blow on the platen to clean off any

loose particles.(2) Spray on a light coating of a window cleaning product or

other similar neutral detergent.Warning: Do not use any other cleaner or the platen may

become damaged.(3) Using a non-abrasive and lintine, pat dry. Be careful not

to scratch the platen. If lint particles adhere to the platensurface, below them off when the platen is dry

32

7/27/2019 BC-2028 Manual

34/50

7 User Acc Opts Guide

7.1. Product Features

Arbitrary time zone and grouping access control function

Manageable access control and attendance recordfunctions

Internal integrated single-door controller, easy to install

Compatible with doorbell

Panel equipped with red and green status indication LED,

water resistance keyboard with white LED light Removal alarm function, voice hint when identification

Adopt standard access control bracket installation

Network management software, easy to manage multi-setof equipments

Compatible with BioID T&A Software management system

Wireless Modem (optional)

Proximity ID card reader (optional)

Wiegand 26 standard output (optional), compatible withother door controllers

Adopt High Speed and large capacity algorithm of BioID

7.2. Basic Concepts

Basic concepts in Access Options function:

Access Options: is the settings of registered usersunlocking time zone and unlocking combination.

Define TZ: is the definition of everyday Time Zone thatcan unlock door in one week.

Grouping (GRP): divides registered users into severalgroups, is easy and convenient to manage.

Effective Time Zone: is the definition of Time Zone inwhich user currently passes verification.

Group Time Zone: is used to set group unlocking

33

7/27/2019 BC-2028 Manual

35/50

User Guide

time.

User Time Zone: is user to set users unlocking time.

Access Comb (Unlocking combination): definesdifferent unlocking combinations, and eachcombination is composed of different groups.

Lock (Time duration of lock drive): fingerprint scannercontrols the time to open electronic lock.

7.3. Access Options

Press MENU key and enter main menu.Press UP and DOWN keys and select Setup. PressOK to enter Setup menu.

Press UP and DOWN keys and select Lock Set. PressOK to enter setting menu of Access Options function, andscreen information displays as follows:

Lock Set

Define TZ

Lock Set

User Acc Opts

Lock Set

GRP TZ Define

Lock SetAccess Comb

Unlock

OpenTime 5

Lock Set

Unlock

Unlock

Time 3

34

7/27/2019 BC-2028 Manual

36/50

Lock Set has 7 main functions:Time Zone is the minimum time definition zone unit in

Access OptionsUser Acc Opts is to process correlative setting according

to users requirement.GRP TZ Define is group Time Zone, and configure group

time zone.Access Combdefines different unlocking combinations, and

each combination is composed of different groups.Unlock fingerprint scanner controls the time to open

electronic lock.

In this menu, user can define and set each function.

7.3.1. Brief Introduction to Access Options

Access Options function setting is the settings of registeredusers unlocking time zone and unlocking combination.

Each users settings are composed of one belonged grouping,use group time zone and user time zone. Grouping is to divide

users into several groups, such as group 1, group2, etc. In grouptime zone, user can select maximum three time zones alreadybeing set. Relationships among these three time zones are OR(i.e. it is only need to satisfy any one of these three time zones). Inuser time zone, user can select maximum three time zones alreadybeing set. Relationships among these three time zones are alsoOR. For details of relationship between use group time zone anduser time zone, please refer to User Access Options .

Simply put, conditions of registered user can unlock doorare:

1: The group that user belongs to should be in unlockingcombination (also this group can be in unlocking combinationwith other groups, but it is required to unlock door together withthem).

2: Current unlocking time should be in any effective time

zone in user time zone.

35

7/27/2019 BC-2028 Manual

37/50

User Guide

System defaults that new registered user belongs to group1, default grouping combination is group 1, and default grouptime zone is 1. Under the condition that group 1 and time zone1 are in factory default status, new registered user defaults inunlocking status (if user changes correlative setting of AccessOptions, system will change according to users modification). Ifthe grouping that user belongs to does not include in groupingcombination setting, then user can only record attendance andcannot unlock door.

7.3.2. Verification Flow of Access Options

36

7/27/2019 BC-2028 Manual

38/50

37

7/27/2019 BC-2028 Manual

39/50

User Guide

7.4. Function Description7.4.1. Definition of Time zone

Time zone is the minimum time zone unit of AccessOptions. Whole system can define maximum 50 time zones. 7time regions (i.e. one week) can be set in each time zone. Eachtime region is effective time zone in 24 hours of a day. Eachuser can set maximum 3 time zones. Relationships amongthese three time zones are OR. It is effective as long as thetime to verify can meet one of these three time zones. Eachtime region format of time zone is HH:MM-HH:MM, i.e. the

format is according to 24-hour mode and accurate to minute.

End-time less than start-time (23:57-23:56) represents all-day forbidden. End-time larger than start-time (00:00- 23:59)represents effective in this region.

Effective time zone for user to unlock: all-day open (00:00-23:59) or end-time larger than start-time in time zone.

Note: System defaults that time zone of serial number 1 is all-dayopen (i.e. new registered user default can unlock door).

1 Enter Define TZ and screen displays as follows:

Press OK to enter setting of time zone 1 and screendisplays as follows:

38

7/27/2019 BC-2028 Manual

40/50

Access Options

Definition of time zone 1 above is all-day open, i.e. factorydefault status.

2 For example:Time zone can be redefined, i.e. definition of time zone 1

is:Saturday and Sunday are break, and not allow to enter.Working time of Monday to Friday allow to enter.Working time: 08:30-18:00

Setting is as follows

39

7/27/2019 BC-2028 Manual

41/50

User Guide

On analogy of this, multi time zones can be defiedaccording to practical requirements. Whole system can define

maximum 50 time zones.

7.4.2. Definition of Grouping Function

Grouping function can divide users into group, and canalso combine different groups into different unlockingcombinations, which are easy and convenient for groupingmanagement of Access Options. And all that, the grouping

function can combine many unlocking combinations. Systemdefines 5 groups: group 1, group 2, group 3, group 4 and group5. New registered user default belongs to group 1, but the usercan be relocate into other group.

Select serial number of Time Zone already being set ingroup Time Zone .New registered user default uses time zone ofgroup 1. But after user resets the belonged group, the user usesdefault time zone of correlative group. So default time zone of

each group should be defined first.For details of use group timezone, please refer to User Access Options.

40

7/27/2019 BC-2028 Manual

42/50

Access Options

Note: time zone of system defaults that group 1 selects serialnumber 1 oftime zone. (i.e. new registered user default can unlock door)

a) Enter GRP 1 TZ Define and screen displays asfollows:

Press OK to enter.

There are 3 time zones in GRP TZ Define. Relationshipsamong these 3 time zones are OR.

Group 1 is effective in time zones of 1, 8 and 40, and canalso select other defined time zones.

b) Enter GRP 2 Dflt TZ and screen displays asfollows:Setting of time zone of group 2:

Press OKto enter.

41

7/27/2019 BC-2028 Manual

43/50

7/27/2019 BC-2028 Manual

44/50

Access Options

of belonged group (group time zone should be set inadvance).

2 If User Time zone is changed, then use group time zone

automatically change to No.

2. Example of setting:

The following example is to set user 00001 and 00002to group 1 and group 2, respectively.

A. Enter setting interface of serial number 00001, and

screen displays as follows:

Press OK to enter setting menu ofuse group time zone.Press UP and DOWN keys and select Yes. Screendisplays as follows:

User of serial number

43

7/27/2019 BC-2028 Manual

45/50

User Guide

00001:Users belonged grouping is 1, it uses time zone of group

1 (serial number of user time zone is serial number of grouptime zone).

User 00001 is effective in time zones of 1, 8 and 48.B. Enter setting interface of serial number 00002, and

screen displays as follows:

Press OK to enter.If serial number of user time zone is 1 or 20, then use

grouptime zone automatically change to No.

User of serial number 00002:Users belonged grouping is 2, it uses user time zone and

does not use group time zone, i.e. it is effective in time zones of1 and 20.

44

7/27/2019 BC-2028 Manual

46/50

Access Options

When user wants to use group time zone, then selectYes. In user time zone, serial number of group time zone willbe automatically assigned the value of serial number of grouptime zone. Contrariwise, if user wants to use user time zone,just directly modify the serial number in user time zone and usegrouptime zone will automatically change to No.

7.4.4. Access Comb

Unlocking combination is the direct representation ofcontrolling unlocking. For example, if user wants that all

registered users cannot unlock, then the user can set all 10unlocking combinations to null.

Unlocking combination definition is to define differentunlocking combinations, and each combination is composed ofdifferent groups. Unlocking combination directly uses groupnumber and does not consider user verification sequencebetween each group. For example 123 represents group 1,group 2, group 3 and at least one user in each group

congregates and passes verification together, then door can beunlocked. 4 represents that after individual user in group 4passes verification, then door can be unlocked. System cansimultaneously define maximum 10 unlocking combinations. Itis required that only one of them passes verification.

Note: Unlocking combination of system initial default setting is 1

(i.e. new registered user default can unlock door).

Press MENU and enter main interface.Select Options and press OK to enter setting menu.Select Access Options and press OK to enter menu.Select Unlocking Combination Definition to enter

Unlocking Combination and screen displays as follows:

45

7/27/2019 BC-2028 Manual

47/50

User Guide

When do not process setting yet (i.e. factory defaultstatus), system defaults that group 1 is unlocking combination 1and others are null.

If do not want to allow all users to unlock door, then set 10unlocking combination all to null.

If only want to allow some groups to unlock door together,

then set these groups in unlocking combination definition.

1) For example:

46

7/27/2019 BC-2028 Manual

48/50

Access Options

From above combination setting, it can be seen that:123 is a combination.4 is a combination.24 is a combination.45 is a combination.15 is a combination.

Combination 1: when personnel of group 1, group 2 andgroup 3 are all on the scene and the time zone is effective in

which at least one user in each group passes verificationtogether, then door can be unlocked.

Combination 2: only one of personnel belonged to group 4is on the scene, then door can be unlocked.

Combination 3: when personnel of group 2 and group 4 areall on the scene and the time zone is effective in which at leastone user in each group passes verification together, then doorcan be unlocked.



47

7/27/2019 BC-2028 Manual

49/50

User Guide

Note: time zones that cannot pass verification User time zone does not select serial number of time zone.

Group time zone does not select serial number of time zone. Time in which user passes verification does not include any time

zone that is set by user.

Time zone is defined as forbidden.

Note: If time zone that user sets is the time zone thatcannot pass verification.

When meet combination 2 above, user who displays prompt ofInvalid Time zone Access cannot unlock door, but can record

attendance. (If there is user in group 4 who can meet unlockingcondition, then combination 2 can unlock door)

When meet combination 1, 3, 4, and 5 above, user who displays

prompt of Invalid Time zone Access cannot unlock door, but canrecord attendance.

2) For example: one bank treasury requires that 3

people are all on the scene to open the door oftreasury. Detailed settings are as follows:

These 3 people belong to group 2, group 4 andgroup 5 respectively, and have the right to unlock doorwithin the same time zone. Select Group 1 andpress OK to enter edit status. Press digit keys toenter 245. Then press ESC to exit and save settinginterface.

Note: When combination 245 is defined, then usercannot define 24, 25, 45 as combination.

48

7/27/2019 BC-2028 Manual

50/50

Access Options

Technical specifications

User capacity 3000Transactioncapacity

80000

Verification mode 1N (recommended) or 11

Access ControlFunction

50 Time Zone5 Grouping10 Access Combsupport multi-fingerprint verification access,Fingerprint or password validating mode,

Electro control Relay output 3A/12VDC

Attendance

FunctionOptional Support BioID attendance software

Else inputA group of door-magnetism input, a group ofbutton of open the door input, a group ofdoorbell input

Communications TCP/IPRS485RS232

Wiiegand output Wiegand26 outputOptional

keyboard andDisplay

4 row 122*32 dots display ,4*4 keypad, whitebacklight

Power12V DC, Stay current50 mA, work current400mA

Validating speed =1 s (full of 3000 fingerprint enrolled)

Sensor Uncoated BioID optical sensor

FRR =0.001%

FAR =0.0001%

OperatingTemperature

0C - 45C

Operating Humidity 20%-80%

Lcd languageEnglish Simplified Chinese TraditionalChineseother languages optional

Voice language English, Chinese, any other languages optional

OEM Supply OEM Made

Size 85L*45W*180Hmm

BC-2028 Manual

Documents

Transcript of BC-2028 Manual