Basswood & Cedar Shutters - Window Treatments€¦ · Basswood & Cedar Shutters can be either fixed...
Transcript of Basswood & Cedar Shutters - Window Treatments€¦ · Basswood & Cedar Shutters can be either fixed...
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
IntroductionBasswood and Cedar Shutters may be used for a variety of reasons: visibility and airflow, controlling the amount of sunlight that enters a room, privacy, security and the ability to enhance the aesthetics of a building or terrace access adding to practicality and mood of any interior. Window Treatment’s traditional European styled Basswood & Cedar shutters are an aesthetically pleasing and versatile window management system. Cedar is recognized for its natural beauty, rich colour, durability, insulating properties and acoustics. Basswood is a hardwood which is durable, lightweight and has a fine straight grain material with an even texture, consistent colour and low resin content. Both Cedar and Basswood have good finishing properties which accept oil based paint and exterior stain for long lasting finishes.
Basswood & Cedar Shutters can be either fixed permanently in place, hinged, bi-fold or sliding depending on your preference and application. Louvres can be adjustable or fixed within the shutter frame. Full height shutters are made with a mid-rail which separates the upper and lower portions of the shutter, with operable louvre shutters this gives greater control as the louvres above the mid-rail can be operated independently from the louvres below the mid-rail. A tilt bar is used for adjusting louvre position and to keep louvres in uniform position. Alternatively a clear view metal tilt rod is placed on the reverse side of the shutter allowing you to adjust all louvres position by tilting one louvre. This also allows for cleaner lines on the front of the shutter and helps to decrease light gap measurements on sliding shutter applications.
Basswood & Cedar Shutters
Quick GlanceType Basswood Cedar
Louvres Louvre Size 47.6mm, 64mm, 89mm, 114mm (Flat Blade or Aerofoil)
68mm (Flat blade), 68mm, 90mm (Aerofoil)
Tilt Bar Tilt Bar PositionClear View
Centre, Left or RightYes
Centre, Left or RightYes
Style HingedBi-foldStraight SlidingFixed Louvres (ventilated)Fixed Louvres (non-ventilated)Special Shape Shutters
YesYesYesYesYesYes
YesYesYesYesYesYes
Stile Options
SquareRabbetD-mould
YesYesYes
YesYesYes
Hard-ware
Tracking SystemsHardware
YesYes
YesYes
Frame Options
StilesMid-railLight StopHang StripsL FramesZ FramesT PostU ChannelCorner Post
YesYesYesYesYesYesYesYesYes
YesYesYesYesYesPainted OnlyYesPainted OnlyPainted Only
Finish StainedOiledLacqueredPainted Powder coated
YesNoNoYes No
NoYesYesYes No
ISSU
E: S
H-0
3-00
3
Sec. : ShuttersDate : Dec 2017Page: 3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Louvre Size and Tensioning ScrewVarious size louvres are available with a choice of two profiles. The first is an areofoil blade which is elliptical in shape (i.e. thicker in the middle and tapered to the front and back). An aerofoil louvre is stronger than the alternative traditional flat blade 68mm louvre.
For Basswood shutters, we have a unique tensioning screw which is used to adjust the tension of the louvres. This comes into its own specifically for full height shutters where adjusting the tensioning screw allows the movement of louvres with ease.
Basswood & Cedar Shutters - Tilt Rod, Louvre Size, Louvre Style,
Cedar Louvre Widths
12mm
12mm
12mm
12mm
11mm
11mm
11mm
11mm
47.6mm
64mm
89mm
114mm 47mm
64mm
89mm
114mm
8
Basswood Louvre Widths
Tilt Rod Control Position: PlantationStandard position for the tilt bar control on Plantation shutters is centred within the frame. Alternatively, the tilt bar can be positioned off-centred left or right. The off-centred option is mainly used for bi-fold panels to allow the panels to fold onto each other without hitting the tilt bar. A tilt rod (in conjunction with a hooked push pole) is also used for high/out of reach and special shaped shutters.
Clear ViewThe Clear View control option for Basswood and Cedar shutters is a metal tilt rod rebated into the side of the louvre blade on the reverse side of the panel. This allows for cleaner lines and a clear view through the shutter once the louvres are opened or closed. The standard Clear View tilt bar position is on the hinged stile side of the louvre blades. The Clear View option is also used for sliding shutter applications as this decreases light gap measurements and allows each shutter panel to sit closer to one another reducing the depth of the shutters when stacked.
Plantation
Clear View
Louvre Style for Special Shape ShuttersFor Basswood and Cedar special shape shutters, Window Treatments supplies 3 louvre style options.
Type Option Available Louvre Size
Basswood Sector 89Full OpenHalf Open
89mm50mm, 64mm, 89mm50mm, 64mm, 89mm
Type Option Available Louvre Size
Cedar Full Open 68mm, 90mm
50, 64, 68, 89, 90mm 50, 64, 89mm
Sec. : ShuttersDate : Dec 2017Page : 4
ISSU
E: S
H-0
3-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
StilesWindow Treatments supplies 3 stile options: Square, Rabbet, and D-mould. For light gaps, Rabbet or D-mould stiles are used to provide a light block where two panels overlap or interlock.
Please Note: If there is only one panel then only square stile is available. When the shutter has 2 panels connected with hinges, all stile options are available.
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
Basswood & Cedar Shutters - Stile options
Square Stiles (Bead)
Square & Rabbet Stiles
Square Stile
Square & D-mould
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
Square stile (Flat)
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points hereSquare Stile (Bead)
51mm 51mm3mm
28m
m
60mm 60mm3mm
28m
m
73mm 47mm3mm
28m
m
60mm 60mm
64mm 38mm3mm
28m
m
51mm 51mm
51mm 51mm4mm
28m
m
25mm
25mm
60mm 60mm4mm
28m
m
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.17Basswood Customer Shutter ProductInfo
A. Square Stiles B. Rabbet Stiles C. D-mould Stiles
There are 2 special points here
ISSU
E: S
H-0
4-00
3
Sec. : ShuttersDate : Dec 2017Page: 5
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Light stop & Mount types, Square frames & Mount types
Shutter Type Type Frame Options Benefit
Basswoodor Cedar
Light Stop A4, A9, Provides a light block where panels are hinged.
Light Stop
Shutter Type Type Frame Options Benefit
BasswoodorCedar
Square Frame B1-1 Standard, B2-1 Beaded
2 Style options are available: Standard and Beaded. Our Standard square frame is best suited to an outside mount application. Our Beaded square frame is best suited to an inside mount application. Using our Standard square frame with a Steadman hinge allows you to protrude the panel past the window opening, giving the ability to hang the shutter panel square in the frame.
Square Frame
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m
8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
varies
varies 19mm
13m
m
varies
varies
30mm30
mm
30mm
30m
m
30mm
30m
m
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm50
mm
20m
m38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m
45mm
19mm
50m
m
20m
m9m
m
45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm
17m
m 38m
m
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
55mm
32mm
30m
m
8mm
55mm
32mm
20m
m
10m
m
8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m
42mm
30m
m
35m
m
55mm
varies
varie
s
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
varies
varies 19mm
13m
m
varies
varies
30mm
30m
m
30mm
30m
m
25.4mm
28.6
mm
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm
50m
m
20m
m
38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m
45mm
19mm
50m
m
20m
m9m
m
45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm
17m
m 38m
m
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
55mm
32mm
30m
m
8mm
55mm
32mm
20m
m
10m
m
8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m
42mm
30m
m
35m
m
55mm
varies
varie
s
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
Sec. : ShuttersDate : Dec 2017Page : 6
ISSU
E: S
H-0
4-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - L Frames & Mount types, T-Posts & Mount types
Shutter Type Type Frame Options Benefit
BasswoodorCedar
L Frame Standard,Beaded, Predrilled
L Frames are used to provide hanging options for single and multiple panels for outside and inside mount applications using a Butt or Steadman hinge. Using Standard and Beaded L Frames with a Steadman hinge allows you to protrude panel past window opening. This gives you the ability to hang the shutter panel square in the frame and closes light gap for flush mounted hinges. Ideal when there is no architrave in the opening.
L Frame
Shutter Type Type Frame Options Benefit
BasswoodorCedar
T Post T1-1 Standard (wide),T2-1 Beaded (wide),Standard (narrow) Beaded (narrow)
T Posts are used to provide hanging options for single and multiple panels for outside and inside mount applications using a Butt hinge. They give you the ability to hang the shutter panel square in the frame. The T Post closes the light gap for flush mounted hinges. Ideal when there is no architrave in the opening.
T Post
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m
8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
13m
m
13mm 19mm
13m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
30mm
30m
m
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm
50m
m
20m
m
38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m
45mm
19mm
50m
m
20m
m9m
m
45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm
17m
m 38m
m
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
55mm
32mm
30m
m
8mm
55mm
32mm
20m
m
10m
m8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m42mm
30m
m
35m
m
55mm
varies
varie
s
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.18Dahao Shutters 01
Inside Mount DirectIN-DI
Inside Mount Hang StripIN-HH
LightStop
HangStrip
Inside Mount IndirectIN-HGH
Steadman HingeButt Hinge
Inside Mount Z-Frame
Z Frame Butt Hinge
HangStrip
Butt Hinge
Inside Mount DirectIN-HGL
Butt Hinge
Inside Mount L-StripIN-L
Butt Hinge
Inside Mount L-Strip with A4 Decorative BeadIN-L
Butt HingeA4 Bead
Outside Mount Hang StripOS-HG
Butt Hinge
Outside Mount on top of Existing TrimOS-HG
Butt Hinge
Outside Mount L-StripOS-L
Butt Hinge
Butt HingeButt Hinge
T-Post
Inside Mount Corner Post
ButtHinge
Existing Trim
Inside MountOutside Mount
Standard Beaded Pre-drilled
T1-1 Standard (wide) T2-1 Beaded (wide) Beaded (narrow) Standard (narrow)
ISSU
E: S
H-0
5-00
3
Sec. : ShuttersDate : Dec 2017Page: 7
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Z Frames, U Channel, Corner Post & Mount types
Shutter Type Type Frame Options Benefit
BasswoodorCedar
Z Frame Standard (short lipped)Standard (plain)Colonial (Basswood only)
Z Frames are used to provide hanging options for single and multiple panels within an opening. Plumbing the window frame closes the light gap for flush mounted hinges. The Z frame wraps around the reveal edge, making it ideal for covering out-of-square windows. 2 style options are available: Standard or Colonial.
Z Frame
Shutter Type Type Frame Options Benefit
BasswoodorCedar
U Channel Top, Bottom
Top and bottom ‘U Channels’ are ideal for incline roof applications or when access to windows is not required. The louvres can open and close and the panel can easily be removed by lifting the shutter up into the top channel and out at the bottom. To refit the reverse applies.
U Channel
Shutter Type Type Frame Options Benefit
BasswoodorCedar
Corner Post CO-PO
Corner Posts are used to provide hanging options for single and multiple panels within a corner application. Closes light gap for flush mounted hinges. Corner Posts are manufactured according to the size required for each installation.
Corner Post
46mm
39m
m
8mm 19mm 19mm
17m
m29
mm
46m
m
36m
m
17m
m29
mm
46m
m
23mm 19mm 19mm
61mm
17m
m29
mm
46m
m
40mm 22mm 19mm33
mm
81mm
Standard (short lipped) Standard (plain) Colonial (Basswood Only)
Shutter Type Type Frame Options Benefit
BasswoodorCedar
Bay Window Post
Bay Window Post
Bay Corner Posts are used to provide hanging options for single and multiple panels within a bay window application. Closes light gap for flush mounted hinges. Bay Window Posts are manufactured according to the size required for each installation.
Bay Window Post
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m
8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
varies
varies 19mm
13m
m
varies
varies
30mm
30m
m
30mm
30m
m
30mm
30m
m
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm
50m
m
20m
m
38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m
45mm
19mm
50m
m
20m
m9m
m
45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm
17m
m 38m
m
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
42mm
30mm
25m
m
10m
m
42mm
30mm
15m
m
10m
m
8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m
42mm
30m
m
35m
m
55mm
varies
varie
s
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
6mm6mm
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m
8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
varies
varies 19mm
13m
m
varies
varies
30mm
30m
m
30mm
30m
m
30mm
30m
m
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm
50m
m
20m
m
38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m
45mm
19mm50
mm
20m
m9m
m45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm
17m
m 38m
m
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm20
mm
50m
m
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
42mm
30mm
25m
m
10m
m
42mm
30mm
15m
m
10m
m
8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m
42mm
30m
m
35m
m
55mm
variesva
ries
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
6mm6mm
Sec. : ShuttersDate : Dec 2017Page : 8
ISSU
E: S
H-0
5-00
3
Can be custom made to suit 41mm35mm
17mm
29mm
19mm 22mm
46mm 41mm
17mm 29mm 22mm
46m
m41
mm
17m
m29
mm
22m
m
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Panel types - Hinged, L Frame & T Post Hinged
Panel TypesPanel Types refers to the variations of each type of shutter: single panel fixed, single panel hinged, bi-folds, L Frame and T Post, straight sliding and bi-fold track variations.
The type of hinge used for a single panel, bi-fold, L Frame and T Post and for Rabbet stiles applications is a Butt hinge. However, if you require your panel to protrude past the window opening, a Steadman hinge is required hinged from a hang strip.
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:5, 1:3,1:100r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :
TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.7Shutter Types 01
41mm
76m
m41
mm
25m
m 33mm
75m
m46
mm
Steadman Hinge Butt Hinge
19mm
50m
m
20m
m
30mm50
mm
30mm38mm
20m
m 45m
m
30mm38mm
15m
m
50m
m
20m
m
30mm38mm
69mm
50mm
20m
m
50m
m
67mm
50mm
20m
m
50m
m
48mm
30mm
10m
m
40m
m
48mm
30mm
10m
m
40m
m
T1-1 T2-1T3-1 T4-1
B8 B9 B10-1B10
Single panelfixed
Single panelhinged at left
Single panelhinged at right
Set of single panelshinged left and right
Single bi-fold shutterpivoted at left
Single bi-fold shutterpivoted at right
Two sets bi-fold shutters
1-A 1-B 2-A 2-B 2-C 2-D
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:5, 1:3,1:100r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :
TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.7Shutter Types 01
41mm
76m
m41
mm
25m
m 33mm
75m
m46
mm
Steadman Hinge Butt Hinge
19mm
50m
m
20m
m
30mm
50m
m
30mm38mm
20m
m 45m
m
30mm38mm
15m
m
50m
m
20m
m
30mm38mm
69mm
50mm
20m
m
50m
m
67mm
50mm
20m
m
50m
m
48mm
30mm
10m
m
40m
m
48mm
30mm
10m
m
40m
m
T1-1 T2-1T3-1 T4-1
B8 B9 B10-1B10
Single panelfixed
Single panelhinged at left
Single panelhinged at right
Set of single panelshinged left and right
Single bi-fold shutterpivoted at left
Single bi-fold shutterpivoted at right
Two sets bi-fold shutters
1-A 1-B 2-A 2-B 2-C 2-D
Hinged
L Frame and T Post HingedWhen tracks are not feasible, L Frame and T Posts are used to provide hanging options for single and multiple panels within an opening or outside the opening window.
Basswood & Cedar (T Post)
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:50r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.24L and T POST
TL T LT
L & T Post Hinged on 6-B
Basswood & Cedar (L Frame)
L Frame & T Post hinge options
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:3r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.10Frame Options
30m
m
40mm
40mm
30m
m
8mm
15m
m
60mm
30m
m
50mm
30m
m
40mm
30m
m
50mm
30m
m
60mm
30m
m
13m
m
13mm 19mm
13m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
30mm30
mm
38mm
30m
m
50mm
30m
m
19mm
30mm
50m
m
20m
m
30mm
38mm
50m
m
20m
m
38mm
30mm
15m
m 45m
m
30mm
38mm
50m
m
20m
m
30mm
38mm
20m
m
50m
m45mm
19mm
50m
m
20m
m9m
m
45mm
48m
m
10mm19mm
17m
m10
mm
50m
m
20m
m13
mm
56mm
10mm30mm
67mm17
mm 38
mm
48m
m
56m
m
41mm
57mm
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
48mm
30mm
10m
m40
mm
48mm
30mm
10m
m40
mm
55mm
32mm
30m
m
8mm
55mm
32mm
20m
m
10m
m
8mm
13m
m
10mm
50mm
65mm
30m
m
35m
m
42mm
30m
m
35m
m
55mm
varies
varie
s
19mm
varie
s
30m
m
8mm
13m
m
60mm 60mm
30m
m
8mm
13m
m
50mm
30m
m
19mm
19m
m
30mm
30m
m
30mm
30m
m
19mm
30mm
20m
m
30mm
38mm
20m
m
69mm
50m
m
50mm
20m
m
69mm
50mm
20m
m50
mm
B3 B4-2B3-2 B20
B22
A7
B8 B9
B12 B13 D2 D3
T1-1 T2-1
B10-1B10 V1
T3-1 T4-1
C1
A4 A9
B1 B1-1 B2-1 B3-1 B4-1
CO-PO
B23
B21
C1-1 C1-3C1-2
B4
C2
C3 C3-1
C4 C4-1
C5 C5-1
Standard Beaded Pre-drilled
T1-1 Standard (wide) T2-1 Beaded (wide) Beaded (narrow) Standard (narrow)
ISSU
E: S
H-0
6-00
3
Sec. : ShuttersDate : Dec 2017Page: 9
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Panel types - Hinged, L Frame & T Post Hinged - Contd.
L Frame and T Post Hinged - cont.
T means Panel is hinged from a T Post or closes onto a T Post
L means Panel is hinged from a L Frame or closes onto a L Frame
means Panel direction to the right
means Panel direction to the left
Key
Sec. : ShuttersDate : Dec 2017Page : 10
ISSU
E: S
H-0
6-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Fixed Shutters
Fixed ShuttersFixed louvres are permanently open (ventilated) or permanently shut (non-ventilated). Permanently open means that there is always ventilation while blocking line of sight. Fixed louvres may be employed for a variety of reasons: to control the amount of sunlight that enters a room, to provide privacy and security, protect against weather, unwanted intrusion or damage and to enhance the aesthetics of a building.
Type A Type C Type D
NormalA-1
ReverseA-2
NormalC-1
ReverseC-2
NormalD-1
ReverseD-2
Stile (Basswood)Stile (Cedar)Louvres (Basswood)Louvres (Cedar)AnglesLouvre FacingProjection (Basswood)Projection (Cedar)Finish (Basswood)Finish (Cedar)
Note: For Flat blade louvres (both Basswood & Cedar) add 2mm to above Projection sizes
50 x 30mm60 x 30mm50, 64, 89, 114mm68, 90mm45°or 60°Normal4, 8, 17, 27mm8, 9, 17mmPainted, StainedPainted, Oiled or Lacquered
50 x 30mm60 x 30mm50, 64, 89, 114mm68, 90mm45°or 60°Reverse0, 2, 9, 17mm0, 3, 9mmPainted, StainedPainted, Oiled orLacquered
50 x 30mm
50mm
45°or 60°Normal
Painted, Stained
50 x30mm
50mm
45°or 60°Reverse
Painted, Stained
50 x 30mm60 x 30mm50, 64, 89, 114mm68, 90mm85°Normal
Painted, StainedPainted, Oiled or Lacquered
50 x 30mm60 x 30mm50, 64, 89, 114mm68, 90mm85°Reverse
Painted, StainedPainted, Oiled or Lacquered
VariationsThe Basswood and Cedar fixed louvre products have many variations such as projections front or back, louvres enclosed within the Stile dimension, louvre angles 45° or 60°, louvre facing up or down, and various louvre sizes: 50mm, 64mm, 68mm, 89mm & 114mm.
fifl fifi fi fi
fi fi fi fifi fi fi fi
Type ANormal
A-1Reverse
A-2
89mm
89m
m
5mm
60m
m
5mm
73m
m
17mm
9mm
30mm
30mm
InteriorView
InteriorView
ExteriorView
ExteriorView
Type DNormal
D-1Reverse
D-2
10m
m
80m
m
10m
m
80m
m
89mm 89
mm
45˚or 60˚
64mm
64m
m
8mm
5mm
42m
m
5mm
51m
m
2mm
114mm
114m
m
5mm
80m
m
5mm
95m
m
27mm
17mm
10m
m
53m
m
10m
m
53m
m
64mm 64
mm
10m
m
100m
m
10m
m
100m
m
114mm
114m
m
30mm 30mmInteriorView
InteriorView
ExteriorView
ExteriorView
89m
m
fifl fifi fi fi
fi fi fi fifi fi fi fi
Type ANormal
A-1Reverse
A-2
89mm
89m
m
5mm
60m
m
5mm
73m
m
17mm
9mm
30mm
30mm
InteriorView
InteriorView
ExteriorView
ExteriorView
Type DNormal
D-1Reverse
D-2
10m
m
80m
m
10m
m
80m
m
89mm 89
mm
45˚or 60˚
64mm
64m
m
8mm
5mm
42m
m
5mm
51m
m
2mm
114mm
114m
m
5mm
80m
m
5mm
95m
m
27mm
17mm
10m
m
53m
m
10m
m
53m
m
64mm 64
mm
10m
m
100m
m
10m
m
100m
m
114mm
114m
m
30mm 30mmInteriorView
InteriorView
ExteriorView
ExteriorView
89m
m
3
ISSU
E: S
H-0
7-00
3
Sec. : ShuttersDate : Dec 2017Page: 11
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood Shutters - Plantation Specifications
Basswood Plantation Specifications
Louvre Size
TypeLouvre - AerofoilLouvre - AerofoilLouvre - AerofoilLouvre - AerofoilLouvre - Flat bladeLouvre - Flat bladeLouvre - Flat bladeLouvre - Flat blade
Size47.6mm x 12mm64mm x 12mm89mm x 12mm114mm x 12mm 47.6mm x 12mm64mm x 12mm89mm x 12mm114mm x 12mm
OptionsHalf Open, Fixed, Ventilated, Fixed Non-Ventilated “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “
Width & Height Hinged
TypeMaximum WidthMaximum WidthMaximum WidthMinimum WidthMinimum HeightMaximum Height
Size900mm (Single Panel hinged)650mm (Bi-fold Panel)1000mm (Sliding or Fixed)250mm (Single Panel)260mm2800mm
Construction
TypeJointsTension Screw & Spring for LouvreLouvre Dowels & SpringEye ScrewPin for Metal Tilt RodClear View Tilt Rod
SizeMortise and Tenon (Top, Middle, Bottom Rail)8g x 70mm Wood Screw Stainless SteelØ4 & Ø 6, 2 Plastic Dowels, Carbon Steel Spring Stainless Steel2g x 20mm, Brass3mm x 14mm, Metal
Finish
TypeStain
Painted
Nature, Oak, Rose, Mahogany, Black walnut, Desert, Ash, Gum-nut, Maple, Coffee bean, Black. or custom colourWhite, Snow, Swiss coffee, Creamy, Butter, Super white, Pearl white, Eggshell, Pearl, Bristle half, Antique white, White on white or custom painted
Recess
Size100mm - 150mm
Please Note: Varies, depending on louvre size. Size of 150mm based on 114mm louvre
Track Systems
TypeMaximum WidthMaximum HeightMaximum Weight
Multi-fold 25650mm per Panel (maximum 8 x Panels on each side)3000mm25kg per Panel
Single Run 60900mm per Panel (maximum 6 x Panels on each track)3000mm60kg per Panel
Stile & Rails
TypeStileTop Rail
Mid Rail
Bottom Rail
Tilt Bar
Size50mm x 30mm Colonial70mm – 160mm x 20mm(varies, depends on height of panel) 50, 64, 90, 114mm x 20mm (varies, depends on Louvre size)Shutters over 1800m 1 mid-rail70mm - 160mm x 20mm(varies, depends on height of panel)19mm x 12mm centred
OptionsSquare, Rabbet, D-mould
Left, Centre, RightClear View
Sec. : ShuttersDate : Dec 2017Page : 12
ISSU
E: S
H-0
7-00
3
12mm
12mm
12mm
12mm
11mm
11mm
11mm
11mm
47.6mm
64mm
89mm
114mm 47.6mm
64mm
89mm
114mm
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood Shutters - Plantation Construction
Basswood Plantation Construction
0
114
0
114
Component List1. Stile2. Top Rail3. Louvre4. Mid Rail5. Bottom Rail6. Tilt Bar 7. Mortise & Tenon
joint8. Tension Screw9. Louvre Dowel10. Eye Screw
2
7
8
ConstructionThe Basswood shutter is constructed using a mortise and tenon joint to join the stiles, middle rail and bottom rail together as one frame. As the shutter height and rail size increase so does the size of the mortise and tenon joint. This strengthens, braces and prevents the frame from twisting, bowing or sagging. The louvres are mounted to the stile using the louvre dowel components, the tilt bar is then mounted to the louvres with the eye screws. The tension screw is then mounted through the stile into the louvre and tensioned. The mid rail must be used when the shutter is over 1800mm in height. This is designed to give greater strength to the shutter frame. The benefit of the mid rail option is that it allows the shutter louvres to have two sections at different angles for privacy, light and airflow. Maximum panel height for Basswood shutters with a mid rail is 2800mm, without a mid rail maximum height is 1800mm.
ISSU
E: S
H-0
8-00
3
Sec. : ShuttersDate : Dec 2017Page: 13
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5, 1:2r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
R E A M E N T S
B.02.4Construction Basswood hidden pull
12
3
4
5
6
10
varies 750mm64mm89mm
LC
Exploded viewof connectingcomponents
Clear view tiltrod
with openingpositions
9
10
7 8
114mm
Basswood Shutters - Plantation Clear View Construction
Component List1. Stile2. Top Rail3. Louvre4. Bottom Rail5. Mortise & Tenon Joint6. Tension Screw7. SS Nail8. SS Nut9. LouvreDowel10. Clear View Aluminium
Basswood Clear View Construction
ConstructionThe Clear View shutter is constructed the same way as the standard Plantation shutter with the exception of the tilt bar which is replaced with the Clear View metal tilt rod option. This tilt bar is rebated into the side of the louvre blade (on the reverse side of the panel) allowing for cleaner lines with unobtrusive view through the shutter when the louvres are open or closed. This option is ideal for sliding shutter applications as this decreases light gap measurements and allows each shutter panel to sit closer to one another.
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5, 1:2r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
R E A M E N T S
B.02.4Construction Basswood hidden pull
12
3
4
5
6
10
varies 750mm64mm89mm
LC
Exploded viewof connectingcomponents
Clear view tiltrod
with openingpositions
9
10
7 8
114mm
Sec. : ShuttersDate : Dec 2017Page : 14
ISSU
E: S
H-0
8-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Cedar Shutters - Cedar Plantation Specifications
Cedar Plantation Specifications
Louvre Size
TypeLouvre - StandardLouvre - AerofoilLouvre - Aerofoil
Size68mm x 10mm68mm x 14mm90mm x 15mm
OptionsHalf Open, Fixed, Ventilated, Fixed Non-Ventilated “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “
Width & Height Hinged
TypeMaximum WidthMaximum WidthMinimum WidthMinimum HeightMaximum Height
Size950mm (Single Panel)500mm (Bi-fold Panel)250mm (Single Panel)260mm3000mm
Construction
TypeJointsPivot Pin for Stile/LouvreBush for Stile/LouvreStaples for Tilt Bar/Louvre
SizeØ10 Dowels (Top, Middle, Bottom Rail)Ø10 x 18mm Pin (Nylon T66)Ø8 x 10mm Bush (Nylon T66)12mm for Tilt Bar (Steel)8mm for Louvre (Steel)
Finish
TypeOiledLacqueredPainted
Clear (polyurethane)Range standard colours or custom colour
Recess
Size92mm - 122mm
Please Note: Varies, depends on Louvre size. Size, 122mm based on 90mm
Track Systems
TypeMaximum WidthMaximum HeightMaximum Weight
Multi-fold 620mm per Panel (maximum 8 x Panels on each side)3000mm25kg per Panel
Single Run 950mm per Panel (maximum 6 x Panels on each track)3000mm60kg per Panel
Stile & Rails
TypeStile
Top RailMid Rail
Bottom Rail
Tilt Bar
Size60mm x 30mm
90mm x 24mm 90mm x 24mm Shutters over 1500mm 1 mid-railShutters over 2950mm 2 mid-rails 90mm - 140mm x 24mm(varies, depends on height of panel)22mm x 12mm centred
OptionsSquareRabbetD-mould
Left, Centre, Rightor Clear View
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:10, 1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.5Specification Cedar
width as specified60mm 60mm
heig
ht a
s sp
ecifi
ed
90m
m90
mm
varie
s
24mm30mm
LC
LC
CLCL
varies92mm - 122mm
varie
s90
mm
- 14
0mm
Section
Elevation
Plan
Section
10m
m
14m
m
15m
m
68mm68mm90mm
ISSU
E: S
H-0
9-00
3
Sec. : ShuttersDate : Dec 2017Page: 15
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Cedar Shutters - Cedar Plantation Construction
Component List1. Stile2. Top Rail3. Mid Rail4. Louvre5. Bottom Rail6. Dowel Joint7. Tilt Bar8. Pivot Bush9. Pivot Pin10. Staples
Cedar Plantation Construction
ConstructionThe Cedar shutter is constructed using hardwood dowelled joints and water based glue that are glued in place to join the stiles, middle rail and bottom rail together as one frame. The dowel size is Ø10mm. All rails have 2 dowels which strengthens, braces and prevents the frame from twisting, bowing or sagging. The louvres are mounted to the stile using the louvre pivot pin and stile bush components. The tilt bar is then mounted to the louvres with staples. A mid-rail must be used when the shutter is over 1500mm in height. This is designed to give greater strength to the shutter frame. Mid rails also allow the shutter louvres to have two sections at different angles for privacy, light and airflow. If the shutter is over 2950mm in height, two mid rails will be necessary.
Sec. : ShuttersDate : Dec 2017Page : 16
ISSU
E: S
H-0
9-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Special Shape Shutters
Special Shape ShuttersShaped panels are designed to cover architecturally or irregular designed windows or openings. Their main attraction is the ability to follow the shape of these openings, keeping the integrity of the design.
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:100,1:75, 1:10r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :
TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.11Special Shape Shutters
Circle SunburstAvailable louvre - 89mm
Quarter SunburstAvailable louvre - 89mm
Circle with Horizontal LouvresAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation only
Eyebrow SunburstAvailable louvre - 89mm
Elongated Eyebrow SunburstAvailable louvre - 89mm
Half Round SunburstAvailable louvre - 89mm
Sunburst at top with T-post and Standard Shutter at bottomAvailable louvres in bottom shutter - 50mm, 64mm, 89mm
Available louvres in Sunburst - 89mmBottom Tilt Rod - Plantation or Clear View
Sunburst with Horizontal LouvresAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation only
ArchAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation or Clear View
Arched Shutters with panel to both sidesAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation or Clear View
RakeAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation or Clear View
TriangleAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation or Clear View
Tapered ShuttersAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation or Clear View
OctagonAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation
Hexagon Straight TopAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation
Hexagon Straight SidesAvailable louvres - 50mm, 64mm, 89mm
Louvre open style - Full open or Half openTilt Rod - Plantation
Sunburst with Horizontal Louvres at top with T-postand Standard Shutter at bottom
Available louvres in bottom shutter - 50mm, 64mm, 89mmAvailable louvres in Sunburst - 89mm
Bottom Tilt Rod - Plantation or Clear View
Elongated Eyebrow Sunburst at top with T-post and Standard Shutter at bottomAvailable louvres in bottom shutter - 50mm, 64mm, 89mm
Available louvres in Sunburst - 89mmBottom Tilt Rod - Plantation or Clear View
L
T
L
L
T
L
L
T
L
ISSU
E: S
H-1
0-00
3
Sec. : ShuttersDate : Dec 2017Page: 17
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Hardware Technical - Tracking systems, Hinges
Hardware Overview
Tracking SystemsWindow Treatments supplies two tracking systems: Multi-fold for bi-fold shutters, and Single Run for straight sliding shutters. For special applications Window Treatments can supply various track options to suit your requirements.
White logo
White logo
Multifold 25for top hung interior folding partitions. Max 25kg each leaf.
APPliCAtioN • Suitableforresidentialandlightcommercialfoldingpartitions • Leavescanbeeitherendfoldingorcentrefolding • Leavescanfoldtooneorbothsidesoftheopening • Pivothardwareenablesanendfoldinginternalpartitiontobedesignedusingstandard widthdoorleaveswithnoneedtoreducethewidthoftheleafadjacenttothejamb DOORSPECIFICATIONTrack System: Multifold 25 ForIndividualLeaves: MaxLeafHeight 2400mm Max leaf Weight 25kg MaxLeafWidth 620mm MinLeafThickness 20mmThefoldingunitisnothingedtoajamb, but pivoted in the track and on the adjustable jambbracket.Endfoldingunitsoftwo,four,sixoreightleavescanbepivotedtoeachsideoftheopening.Centrefoldingunitsofone,three,fiveorsevenfullwidthleavesandone“half”widthleafcanbepivotedtoeachsideoftheopening.Aguidesystemacrossthefloormustbeusedonendfoldingunitsoffourleavesormoreinexcessof450mmwideor15kgperleaf.Instructionsonleafwidthcalculationisshownoverleaf.Doorleavesshouldbeconstructedtoprovidesecurefittingforthepivots,hangers,hingesandguidesandcanbeeitherflush,panelledoroflouvreconstruction. STANDARDSETSANDPACKS Set No. Contents AMf2 2 door pack AMf4 4 door pack AMf6 6 door pack HARDWARESPECIFICATIONTrack – punched for soffit fitting: A60A Material Aluminium Standardlengths 2000mm,3000mm,4000mmand6000mmTop Pivot Assembly: AMF25TP Steel,Zincdichromated,NylonBottom Pivot: AMF25BP Steel,Zincdichromated,NylonHanger: A60SN Thehangerisfittedwithfournylontyredballracewheels.Theadjustmentboltisattachedtothetopplateandsecuredinplacewithalockingclipwhichallowseasyinstallation.Allsteelpartsarezincdichromated.Hinges: A75X47FHSS Stainlesssteelnonmortisehinge Screwsforthehingesarestainlesssteel.Theotherscrewsareinzincdichromatefinish.Spanner: A60SP Steel,inzincdichromatefinishAccessories: Bracket: ADP1/60 Bracketmadefromsteelandsuppliedwithmatchingfasteners.Availableinapackof5or8,reference1/60/5and1/60/8respectively.Channels: A901Aaluminiumchannel,availablein1200,1500,1800, 2400and3600mmGuide: A8G/901 Springloadedguideforusewith901Aor902Achannels.Guideisnylonandstainlesssteel.Threshold: A902A A902Athreshold,aluminium,availablein2100,3000,4000and6000mmFlush Pull – with deep grip: A401Flush Bolt – with flat shoot: A360
ISSUE1 DATASHEETD40
No.A75x47FHSS Hinge
No.ADP1/60Bracket
AMF25BPBottomPivot
AMF25TPTopPivot
Stainless Steel
SNo.A60SNHanger
Stainless Steel
S
No.A8G/901
No.A901AChannel No. A902A Channel
White logo
White logo
Stainless Steel
S
Stainless Steel
S
single run 60For top hung straight sliding doors. Max 60kg each.
APPliCATiOn • Widelyusedinlightercommercialandindustrialapplications• Tocoveranywidthofopening,anynumberofdoorscanbeused• Toaccommodatedifferentbuildingdesigns,doorscanslidetooneorbothsides• Hingeddoorforeasyaccessmaybeincorporatedintoaslidingdoor• Wheredoorsarefittedexternally,acanopyisrecommended DOOr sPeCiFiCATiOnTrack System: Single Run 60 ForIndividualDoors: MaxDoorHeight 2400mm MaxDoorWeight 60kg DoorThickness 19-48mmForeaseofoperationitisrecommendedthatthedoorwidthshouldnotexceed75%ofdoorheight.Timberdoorsforinteriorusecanbeofflushconstructionorglazed.Timberdoorsforindustrialapplicationsshouldbeframed,ledgedandbraced.Metaldoorsshouldbeconstructedofboxsection,channelorangleframing,wellbracedandcladwithflatorcorrugatedsheets. sTAnDArD seTSetcompriseshangers,doorstops,nylonguide,screwsandinstructions.
Pack Set No APD60TheAPD60isapackoffittingsonlywithouttrack. HARDWARESPECIFICATIONTrack: A60A Material Aluminium Standardlengths 2000mm,3000mm,4000mmand6000mmAluminiumtrackavailableinmillorclearanodised.Brackets: Packof5Brackets A1/60/5 Packof8Brackets A1/60/8Bracketmadefromzincplatedsteel.Suppliedwithmatchingfasteners.Hangers (2 per door): interior A60sn exterior A60sss Allhangershavenylontyrewheelsandarefittedwithballracebearings.The60SNHangerhasanylonbodyandchromeprecisionbearings.The60SSShangerhasastainlessbodyandprecisionbearings.Nylontyrewheelhangersshouldnotbeusedoninstallationsinvolvingtemperaturesexceeding80°C.Guides: 1GNSawCutThisnylonGuideisdesignedtoslidethrougha20mmdeepx5mmwidesawcutinthebottomrailofthedoor.TheGuideisfittedonthefloorattheedgeoftheopeningintheoverlaparea.Spanner: A60sPPressedsteelzincplatedAccessories: Channels: A901A A902AGuide: A8G/901SpringloadedSpringloadedGuide,nylonbodyandtipwithstainlesssteelshaftandspring.Designedtoslideinthe901Channeland902thresholdChannel
no. A1gn guide
No.A1/60Bracket
No.A60SNHanger
No.60SNHangerno. A60sP spanner
No.A60SSSHanger stainless steel
No.A8G/901
no. A60Ds stop (supplied in sets
and packs)
ISSUE1 DATASHEETB80
Stainless Steel
S
no. A901A Channel
No.A902AChannel
HingesDepending on the type of shutter installation, Butt Hinge and Steadman Hinge are the standard hinges. For special applications, Window Treatments also supplies various hinge options such as Handle hinges to suit your requirements.
Multi-fold for Bi-fold shutters
Single Run for straight sliding
Type Colours Available Suitable for
Butt Hinge Stainless Steel, Silver, Cream, White, Black, Antique Brass, Bright Brass
Square, Rabbet, T Post, L Frame
Steadman Hinge Stainless Steel, Silver, Cream, White, Black, Antique Brass, Bright Brass
Hang Strip, protruding past window opening
Handle Hinge Stainless Steel Bi-fold, assists panel movement
Barrel Bolt Stainless Steel Bi-fold, Sliding, Panel
Ball Stops Brass, Chrome Securing Fixed Panel
Magnetic Catch Brown, White, Black Securing Bi-fold Panel
Butt Hinge Steadman Hinge Handle Hinge
Barrel Bolt
Ball Stop
Magnetic Catch
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.13Hardware
63mm
76m
m88
mm
65mm 38mm
63m
m
26m
m
12mm 10mm
16mm
60m
m
25mm
16m
m
26mm
36m
m10
0mm
25mm
20mm
25m
m
11mm
16mm
11mm11mm
38m
m
13mm
60m
m
11mm
9mm8mm
48m
m
26m
m
20m
m
28mm
14m
m
45mm
14mm
Large Ball Stops Medium Ball Stops Magnetic Catch
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:5, 1:3,1:100r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :
TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.7Shutter Types 01
41mm
76m
m41
mm
25m
m 33mm
75m
m46
mm
Steadman Hinge Butt Hinge
19mm
50m
m
20m
m
30mm
50m
m
30mm38mm
20m
m 45m
m
30mm38mm
15m
m
50m
m
20m
m
30mm38mm
69mm
50mm
20m
m
50m
m
67mm
50mm
20m
m
50m
m
48mm
30mm
10m
m
40m
m
48mm
30mm
10m
m
40m
m
T1-1 T2-1T3-1 T4-1
B8 B9 B10-1B10
Single panelfixed
Single panelhinged at left
Single panelhinged at right
Set of single panelshinged left and right
Single bi-fold shutterpivoted at left
Single bi-fold shutterpivotedat right
Two sets bi-fold shutters
1-A 1-B 2-A 2-B 2-C 2-D
D A T E : S H T n o ~ :
S C A L E S :
A 4
Sunday, 25 November2012
1:5, 1:3,1:100r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :
TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.7Shutter Types 01
41mm
76m
m41
mm
25m
m 33mm
75m
m46
mm
Steadman Hinge Butt Hinge
19mm
50m
m
20m
m
30mm
50m
m
30mm38mm
20m
m 45m
m
30mm38mm
15m
m
50m
m
20m
m
30mm38mm
69mm
50mm
20m
m
50m
m
67mm
50mm
20m
m
50m
m
48mm
30mm
10m
m
40m
m
48mm
30mm
10m
m
40m
m
T1-1 T2-1T3-1 T4-1
B8 B9 B10-1B10
Single panelfixed
Single panelhinged at left
Single panelhinged at right
Set of single panelshinged left and right
Single bi-fold shutterpivoted at left
Single bi-fold shutterpivotedat right
Two sets bi-fold shutters
1-A 1-B 2-A 2-B 2-C 2-D
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.13Hardware
63mm
76m
m88
mm
65mm 38mm
63m
m
26m
m
12mm 10mm
16mm
60m
m
25mm
16m
m
26mm
36m
m10
0mm
25mm
20mm
25m
m
11mm
16mm
11mm11mm
38m
m
13mm
60m
m
11mm
9mm8mm
48m
m
26m
m
20m
m
28mm
14m
m
45mm
14mm
Large Ball Stops Medium Ball Stops Magnetic Catch
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.13Hardware
63mm
76m
m88
mm
65mm 38mm
63m
m
26m
m
12mm 10mm
16mm
60m
m
25mm
16m
m
26mm
36m
m10
0mm
25mm
20mm
25m
m
11mm
16mm
11mm11mm
38m
m
13mm
60m
m
11mm
9mm8mm
48m
m
26m
m
20m
m
28mm
14m
m
45mm
14mm
Large Ball Stops Medium Ball Stops Magnetic Catch
D A T E : S H T n o ~ :
S C A L E S :
A 4
Friday, 30 November2012
1:5r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED
W I N D O W T R E A M E N T S
B.02.13Hardware
63mm
76m
m88
mm
65mm 38mm
63m
m
26m
m
12mm 10mm
16mm
60m
m
25mm
16m
m
26mm
36m
m10
0mm
25mm
20mm
25m
m
11mm
16mm
11mm11mm
38m
m
13mm
60m
m
11mm
9mm8mm
48m
m
26m
m
20m
m
28mm
14m
m
45mm
14mm
Large Ball Stops Medium Ball Stops Magnetic Catch
13mm
12mm
35mm
8mm
85mm
52mm
145m
m
7mm
17m
m
Magnetic Catch
12mm
15mm
16m
m
Sec. : ShuttersDate : Dec 2017Page : 18
ISSU
E: S
H-1
0-00
3
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Hardware Technical - Sliding Single Run
White logo
White logo
Stainless Steel
S
Stainless Steel
S
single run 60For top hung straight sliding doors. Max 60kg each.
APPliCATiOn • Widelyusedinlightercommercialandindustrialapplications• Tocoveranywidthofopening,anynumberofdoorscanbeused• Toaccommodatedifferentbuildingdesigns,doorscanslidetooneorbothsides• Hingeddoorforeasyaccessmaybeincorporatedintoaslidingdoor• Wheredoorsarefittedexternally,acanopyisrecommended DOOr sPeCiFiCATiOnTrack System: Single Run 60 ForIndividualDoors: MaxDoorHeight 2400mm MaxDoorWeight 60kg DoorThickness 19-48mmForeaseofoperationitisrecommendedthatthedoorwidthshouldnotexceed75%ofdoorheight.Timberdoorsforinteriorusecanbeofflushconstructionorglazed.Timberdoorsforindustrialapplicationsshouldbeframed,ledgedandbraced.Metaldoorsshouldbeconstructedofboxsection,channelorangleframing,wellbracedandcladwithflatorcorrugatedsheets. sTAnDArD seTSetcompriseshangers,doorstops,nylonguide,screwsandinstructions.
Pack Set No APD60TheAPD60isapackoffittingsonlywithouttrack. HARDWARESPECIFICATIONTrack: A60A Material Aluminium Standardlengths 2000mm,3000mm,4000mmand6000mmAluminiumtrackavailableinmillorclearanodised.Brackets: Packof5Brackets A1/60/5 Packof8Brackets A1/60/8Bracketmadefromzincplatedsteel.Suppliedwithmatchingfasteners.Hangers (2 per door): interior A60sn exterior A60sss Allhangershavenylontyrewheelsandarefittedwithballracebearings.The60SNHangerhasanylonbodyandchromeprecisionbearings.The60SSShangerhasastainlessbodyandprecisionbearings.Nylontyrewheelhangersshouldnotbeusedoninstallationsinvolvingtemperaturesexceeding80°C.Guides: 1GNSawCutThisnylonGuideisdesignedtoslidethrougha20mmdeepx5mmwidesawcutinthebottomrailofthedoor.TheGuideisfittedonthefloorattheedgeoftheopeningintheoverlaparea.Spanner: A60sPPressedsteelzincplatedAccessories: Channels: A901A A902AGuide: A8G/901SpringloadedSpringloadedGuide,nylonbodyandtipwithstainlesssteelshaftandspring.Designedtoslideinthe901Channeland902thresholdChannel
no. A1gn guide
No.A1/60Bracket
No.A60SNHanger
No.60SNHangerno. A60sP spanner
No.A60SSSHanger stainless steel
No.A8G/901
no. A60Ds stop (supplied in sets
and packs)
ISSUE1 DATASHEETB80
Stainless Steel
S
no. A901A Channel
No.A902AChannel
Application• Widely used in lighter commercial and industrial applications• To cover any width of opening, any number of panels can be used• To accommodate different building designs, panels can slide to one or both sides• Hinged panel for easy access may be incorporated into a sliding panel• Where panels are fitted externally, a canopy is recommended
Panel SpecificationTrack System: Single Run (individual Panels)Max Panel Height: Basswood 3000mm Cedar 2700mmFor ease of operation it is recommended that the panel width should not exceed 75% of the panel height.Panels for interior use can be of flush construction or glazed. Panels for industrial applications should be framed, ledged and braced.
Hardware SpecificationTrack : 80AMaterial : AluminiumStandard lengths : 2000mm, 3000mm, 4000mm, 6000mmAluminium track available in mill or clear anodised finish.
Door Stop : 20DS (Stainless Steel)
Hangers (2 per door) : Interior : No. 57EN HamgerHangers supplied with fixing plate and nylon tyred precision bearings. Vertical adjustment is simple and positive. Nylon tyre wheel hangers should not be used on installation involving temperatures exceeding 800C.
Guide : No. 801SSpring loaded guide, nylon body and tip with stainless steel shaft and spring.Designed to slide in the No. 92 Threshold
ISSU
E: S
H-1
1-00
3
Sec. : ShuttersDate : Dec 2017Page: 19
SPEC
IFIC
ATIO
NS
.
www.window-treatments.co.nz
Basswood & Cedar Shutters - Hardware Technical - Multi-fold
Application• Suitable for residential and light commercial folding shutters with all panels
of equal width. Panels can fold to one or both sides of the opening• Pivot hardware enables a folding exterior shutter to be designed using
equal width panels with no cutting down of the panel adjacent to the post.• To cover any width opening, any number of folding untits can be used.
Panel SpecificationTrack System: Multi-fold (individual leaves)Max Leaf Height: Basswood 2500mm Cedar 2500mmMax Leaf Width: Basswood 700mm Cedar 750mm
Units of up to six panels can be pivoted to each side of the opening.A guide system across the floor must be used on units of three panels or more. Floating units consist of four to six panels.Shutters should be constructed to provide secure fitting for the pivot sets, hangers, hinges and guides.
White logo
White logo
Multifold 25for top hung interior folding partitions. Max 25kg each leaf.
APPliCAtioN • Suitableforresidentialandlightcommercialfoldingpartitions • Leavescanbeeitherendfoldingorcentrefolding • Leavescanfoldtooneorbothsidesoftheopening • Pivothardwareenablesanendfoldinginternalpartitiontobedesignedusingstandard widthdoorleaveswithnoneedtoreducethewidthoftheleafadjacenttothejamb DOORSPECIFICATIONTrack System: Multifold 25 ForIndividualLeaves: MaxLeafHeight 2400mm Max leaf Weight 25kg MaxLeafWidth 620mm MinLeafThickness 20mmThefoldingunitisnothingedtoajamb, but pivoted in the track and on the adjustable jambbracket.Endfoldingunitsoftwo,four,sixoreightleavescanbepivotedtoeachsideoftheopening.Centrefoldingunitsofone,three,fiveorsevenfullwidthleavesandone“half”widthleafcanbepivotedtoeachsideoftheopening.Aguidesystemacrossthefloormustbeusedonendfoldingunitsoffourleavesormoreinexcessof450mmwideor15kgperleaf.Instructionsonleafwidthcalculationisshownoverleaf.Doorleavesshouldbeconstructedtoprovidesecurefittingforthepivots,hangers,hingesandguidesandcanbeeitherflush,panelledoroflouvreconstruction. STANDARDSETSANDPACKS Set No. Contents AMf2 2 door pack AMf4 4 door pack AMf6 6 door pack HARDWARESPECIFICATIONTrack – punched for soffit fitting: A60A Material Aluminium Standardlengths 2000mm,3000mm,4000mmand6000mmTop Pivot Assembly: AMF25TP Steel,Zincdichromated,NylonBottom Pivot: AMF25BP Steel,Zincdichromated,NylonHanger: A60SN Thehangerisfittedwithfournylontyredballracewheels.Theadjustmentboltisattachedtothetopplateandsecuredinplacewithalockingclipwhichallowseasyinstallation.Allsteelpartsarezincdichromated.Hinges: A75X47FHSS Stainlesssteelnonmortisehinge Screwsforthehingesarestainlesssteel.Theotherscrewsareinzincdichromatefinish.Spanner: A60SP Steel,inzincdichromatefinishAccessories: Bracket: ADP1/60 Bracketmadefromsteelandsuppliedwithmatchingfasteners.Availableinapackof5or8,reference1/60/5and1/60/8respectively.Channels: A901Aaluminiumchannel,availablein1200,1500,1800, 2400and3600mmGuide: A8G/901 Springloadedguideforusewith901Aor902Achannels.Guideisnylonandstainlesssteel.Threshold: A902A A902Athreshold,aluminium,availablein2100,3000,4000and6000mmFlush Pull – with deep grip: A401Flush Bolt – with flat shoot: A360
ISSUE1 DATASHEETD40
No.A75x47FHSS Hinge
No.ADP1/60Bracket
AMF25BPBottomPivot
AMF25TPTopPivot
Stainless Steel
SNo.A60SNHanger
Stainless Steel
S
No.A8G/901
No.A901AChannel No. A902A Channel
White logo
White logo
Multifold 25for top hung interior folding partitions. Max 25kg each leaf.
APPliCAtioN • Suitableforresidentialandlightcommercialfoldingpartitions • Leavescanbeeitherendfoldingorcentrefolding • Leavescanfoldtooneorbothsidesoftheopening • Pivothardwareenablesanendfoldinginternalpartitiontobedesignedusingstandard widthdoorleaveswithnoneedtoreducethewidthoftheleafadjacenttothejamb DOORSPECIFICATIONTrack System: Multifold 25 ForIndividualLeaves: MaxLeafHeight 2400mm Max leaf Weight 25kg MaxLeafWidth 620mm MinLeafThickness 20mmThefoldingunitisnothingedtoajamb, but pivoted in the track and on the adjustable jambbracket.Endfoldingunitsoftwo,four,sixoreightleavescanbepivotedtoeachsideoftheopening.Centrefoldingunitsofone,three,fiveorsevenfullwidthleavesandone“half”widthleafcanbepivotedtoeachsideoftheopening.Aguidesystemacrossthefloormustbeusedonendfoldingunitsoffourleavesormoreinexcessof450mmwideor15kgperleaf.Instructionsonleafwidthcalculationisshownoverleaf.Doorleavesshouldbeconstructedtoprovidesecurefittingforthepivots,hangers,hingesandguidesandcanbeeitherflush,panelledoroflouvreconstruction. STANDARDSETSANDPACKS Set No. Contents AMf2 2 door pack AMf4 4 door pack AMf6 6 door pack HARDWARESPECIFICATIONTrack – punched for soffit fitting: A60A Material Aluminium Standardlengths 2000mm,3000mm,4000mmand6000mmTop Pivot Assembly: AMF25TP Steel,Zincdichromated,NylonBottom Pivot: AMF25BP Steel,Zincdichromated,NylonHanger: A60SN Thehangerisfittedwithfournylontyredballracewheels.Theadjustmentboltisattachedtothetopplateandsecuredinplacewithalockingclipwhichallowseasyinstallation.Allsteelpartsarezincdichromated.Hinges: A75X47FHSS Stainlesssteelnonmortisehinge Screwsforthehingesarestainlesssteel.Theotherscrewsareinzincdichromatefinish.Spanner: A60SP Steel,inzincdichromatefinishAccessories: Bracket: ADP1/60 Bracketmadefromsteelandsuppliedwithmatchingfasteners.Availableinapackof5or8,reference1/60/5and1/60/8respectively.Channels: A901Aaluminiumchannel,availablein1200,1500,1800, 2400and3600mmGuide: A8G/901 Springloadedguideforusewith901Aor902Achannels.Guideisnylonandstainlesssteel.Threshold: A902A A902Athreshold,aluminium,availablein2100,3000,4000and6000mmFlush Pull – with deep grip: A401Flush Bolt – with flat shoot: A360
ISSUE1 DATASHEETD40
No.A75x47FHSS Hinge
No.ADP1/60Bracket
AMF25BPBottomPivot
AMF25TPTopPivot
Stainless Steel
SNo.A60SNHanger
Stainless Steel
S
No.A8G/901
No.A901AChannel No. A902A Channel
Hardware SpecificationTrack - punched for soffit fitting: 80AMaterial : AluminiumStandard lengths : 2000mm, 3000mm, 4000mm, 6000mm
Top Pivot Assembly : 21EPNC Steel, Zinc dichromated, Nylon
Bottom Pivot : 21EPNC Steel, Zinc dichromated, Nylon
Door Stop : 20DS (Stainless Steel)
Hangers : No. 57EN HangerThe hanger is fitted with four nylon tyred ballrace wheels. The adjustment bolt is attached to the top plate and secured in place with a blocking clip which allows easy installation. All steel parts are zinc dichromated.
Guide : No. 801SSpring loaded guide for use with No.92 Threshold. Guide is nylon and stainless steel.
Threshold : No. 92Threshold, aluminium, available in 2100mm, 3000mm, 4000mm, 6000mm
No.21EPNC Top Pivot
Sec. : ShuttersDate : Dec 2017Page : 20
ISSU
E: S
H-1
1-00
3