Basic electrical math
-
Upload
northeast-texas-community-college -
Category
Education
-
view
15.465 -
download
1
description
Transcript of Basic electrical math
Basic Electrical MathPresented by Jim Wylie
This pre-class is to help you to prepare for the Solar Technician Course.
The goal is to be able to understand the technical lessons of the main course, not become frustrated or fall behind the other students.
Jim Wylie, your instructor, has posted regular office hours to help you to successfully complete the Solar Technician Course. If you need times not posted, contact Jim by email or Blackboard and make other arrangements.
Introduction PV Installers must be able to calculate simple electrical formula problems.
PV Installers must be able to do simple geometric and trigonometric problems
The instructor assumes that students are capable of simple addition, subtraction, multiplication and divisions.
The instructor realizes that students may not remember or have a good foundation in algebra.
Training OutlineLesson 1: Voltage, Amperes and
ResistanceLesson 2: Series Electric CircuitsLesson 3: Parallel Electric CircuitsLesson 4: Electric SourcesLesson 5: Sun angle and Solar
Panel Orientation
OHMS LAW V=IR
Ohms Law is possibly the most important concept to learn in electrical technology. It is used by every electrician and equally used by solar installers. The formula E=IR explains the relationship of current, resistance to the voltage of all electric circuits. In this lesson we will use the Ohms formula to explain the relationship of volts, amps and ohms.
Learn this lesson well before you continue to Lesson Two. If you feel that you are not learning the lesson, contact the instructor during his office hours for some help.
Lesson 1: Apply Ohms LawThe formula V=IR is manipulated to
calculate the I (current) when we know the V (voltage) and R (resistance)
You must learn that V=IR and thatV=Voltage, I=Amps and R=Resistance
Repeat: LEARN THIS FORMULA – Electrical potential equals the current times the resistance or V=IR. The electrical potential is measured in volts. Current is measured in amps and resistance is measured in ohms.
Calculate the CurrentIf V=IR, to get I= ? First divide on both sides of the equal sign by R.V/R=IR/R the answer is V/R=I or reverse the formula I=V/R
Explanation:The current in amps is equal to electrical potential in volts divided by resistance in ohms or the current in amps is inversely proportional to the resistance in ohms and directly proportional to the electrical pressure (potential) in volts.
Lesson 1: ContinueUsing the same process for
calculating (I), calculate (R)Remember that Ohms Law is V=IR (memorized by now)
We calculate the formula for resistance (R) when you know what the voltage potential and current in amps are ?
Go to the next slide and see if you have the correct answer reasoning. If the answer is wrong go back to the first slide in this lesson before continuing.
Answer: Find R, If V=IR
V=IR by dividing both sides of the equal sign by I. V/I=IR/I The results is V/I=R or R=V/I
QUIZ: Describe the process and results in math terms? Stand on your head for the answer
You can say that the resistance in ohms is equal to electrical potential in volts divided by current in amps or you can say that resistance in ohms is inversely proportional to the current in amps and directly proportional to the electrical pressure (potential) in volts.
Calculate the ResistanceIf V=IR, to get R= ? First divide on both sides of the equal sign by I.V/I=IR/I the answer is V/I=R or reverse the formula R=V/I
Explanation:The Resistance in ohms is equal to electrical potential in volts divided by current in amps or the resistance in ohms is inversely proportional to the current in amps and directly proportional to the electrical pressure (potential) in volts.
Instructor’s Tips:About now you may be asking – What in the World are we doing? If so here is a few tips.
1. If you do not understand the lesson slide then reread it until it makes sense or try memorizing it and continue on to the next slide.
2. Repeat this same procedure for each slide until you finish the lesson.
3. The review slide will contain all variations of Ohms Law – memorize the variations if you cannot calculate them.
4. The last slide in the lesson will be using real numbers instead of letters. This might make more sense to you.
5. Lastly, review the complete lesson and if all else fails call the instructor for help.
Lesson 1 Review Memorize the three variations of
Ohms Law: V=IR I=V/R R=V/I
Explain each of the Ohm’s Law variation with mathematical terms –
Using numbers is usually easier than letter in a formula. Go to the self-test next slide and see if you know how to use Ohm’s Law.
Lesson 1 – Practice Problems Resistance – (R) in Ohms
Electrical Potential –(V) in Volts
Current – (I) in Amps
15 120 A
R 500 50
37 24 A
75 V 20
R 240 60
100 V 5
Solve for the unknown in red
Answer to ProblemsResistance – (R) in Ohms
Electrical Potential –(V) in Volts
Current – (I) in Amps
15 120 8
10 500 50
37 24 0.649
75 1500 20
4 240 60
100 500 5
V=IRR=V/II=V/R
Lesson 2: Series Electric CircuitsA series circuit is connected in a
line with the back side of electrical object attached to the front side of the next electrical object.
Lesson 2: How It WorksSERIES
CIRCUITS
A Series Circuit has only one path to ground, so electrons must go through each component to get back to ground. All loads are placed in series.
1. An open in the circuit will disable the entire circuit.
2. The voltage divides (shared) between the loads.
3. The current flow is the same throughout the circuit.
4. The resistance of each load can be different
Lesson 2: Voltage DropVOLTAGE DROP CALCULATION
When current flows in a circuit, the presence of a resistance in that circuit will cause the voltage to fall or drop as it passes through the resistance. The resultant difference in the voltage on each side of the resistance is called a voltage drop. When current (I) flows in the following circuit, voltage drops V1 and V2 across resistances R1 and R2 can be determined as follows from Ohm's law. (The value of current I is the same for both R1 and R2 since they are connected in series.)
Series Voltage Drop Calculation
example:
SERIES CIRCUIT SUMMARYRemember these points and understand how the voltage drop calculations are done
There is only one path to the ground
Current remains the same throughout the circuit
The presence of a resistance in the circuit will cause the voltage to drop
Lesson 3: Parallel Circuits
A parallel circuit is like a ladder with the steps being the resistance between the sides representing the positive and negative wires. Voltage and current flows independently through each resistant step.
Lesson 3: How It Works PARALLEL CIRCUIT
A parallel circuit has more than one path for current flow. The same voltage is applied across each branch. If the load resistance in each branch is the same, the current in each branch will be the same. If the load resistance in each branch is different, the current in each branch will be different. If one branch is broken, current will continue flowing to the other branches.
Lesson 3: calculationsResistance in a parallel circuit is
calculated with the formula:
Current is calculated by the formula:
PARALLEL CIRCUIT SUMMARYRemember these points and understand how the resistance and current calculations are done
A parallel circuit will have more than one path to the ground
The same voltage will appear across each branch
Different current will result from different resistance of the branches
If a branch is opened current will continue through the other branches
Lesson 3: Power Sources
We will use our knowledge of Ohms Law, Series and Parallel electric circuits to understand how power sources like batteries and solar panels work.
Power Source in SeriesVoltage will increase by adding
each individual battery or solar panel to find the total voltage of battery pack or array
Current will remain the same
Power Source in ParallelCurrent will increase by adding
each individual battery or solar panel to find the total current of battery pack or array
Voltage will remain the same
Summary of TrainingList important points from each
lesson.Provide resources for more
information about the subject.◦List resources on this slide.◦Provide handouts with additional
resource material.
Reread lesson three to commit the points to memory
Solar panels are wired through a controller, inverter and electrical panel.
Lesson 4: Sun angle and Solar Panel Orientation
Assessment and EvaluationPrepare a quiz or challenge to
assess how much information participants learned.
Survey participants to see if they found the training beneficial.